Generac XG8000E 0058462 Manuel utilisateur

Marque: Generac

Modèle: XG8000E 0058462

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

www.generac.com or 1-888-436-3722

Owner's Manual

XG 6500-8000 Watt Series Portable Generators



DEADLY EXHAUST FUMES! ONLY use OUTSIDE

far away from windows, doors and vents!



NOT INTENDED FOR USE IN CRITICAL LIFE

SUPPORT APPLICATIONS.



SAVE this Manual. Provide this manual to any

operator of the generator.

Introduction ............................................................. 1

Read this Manual Thoroughly ................................. 1

Safety Rules ...........................................................1

Standards Index .............................................................3

General Information ................................................ 4

1.1 Unpacking ......................................................................4

1.2 Assembly .......................................................................4

1.3 Emissions Information....................................................5

1.4 Product Specifications....................................................5

Operation ................................................................ 5

2.1 Know the Generator .......................................................5

2.2 Hourmeter - No Reset ....................................................7

2.3 Hourmeter - With Reset ..................................................7

2.4 Cord Sets and Connection Plugs ....................................8

2.5 How to Use the Generator ..............................................8

2.6 Don’t Overload the Generator ..........................................9

2.7 Wattage Reference Guide .............................................10

2.8 Before Starting the Generator .......................................10

2.9 To Start the Engine .......................................................11

2.10 Stopping the Engine .....................................................12

2.11 Low Oil Pressure Shutdown System .............................12

2.12 Charging the Battery .....................................................12

Maintenance ......................................................... 13

3.1 Maintenance Schedule .................................................13

3.2 General Recommendations ...........................................13

3.3 Service Air Filter ...........................................................14

3.4 Clean Spark Arrestor Screen.........................................14

3.5 Adjusting Valve Clearance ............................................15

3.6 General ........................................................................15

3.7 Long Term Storage .......................................................15

3.8 Other Storage Tips .......................................................16

Battery Service ..................................................... 16

4.1 Battery Replacement ....................................................16

Troubleshooting .................................................... 17

5.1 Troubleshooting Guide ..................................................17

MANUAL DEL PROPIETARIO ............................. 19

MANUEL DU PROPRIÉTAIRE ............................. 39

Table of Contents

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Authorized Dealer for starting, operating and servicing

procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using the

equipment. We also strongly recommend instructing other users to

properly start and operate the unit. This prepares them if they need

to operate the equipment in an emergency.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

• Become familiar with and strictly adhere to all local, state and

national codes and regulations.

• Study all safety warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.





This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

GENERAL HAZARDS

• NEVER operate in an enclosed area, in a vehicle, or indoors

EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends that the

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

• Operate generator only on level surfaces and where it will not be

exposed to excessive moisture, dirt, dust or corrosive vapors.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving parts. Never remove any fan guard or shield

while the unit is operating.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

• Do NOT operate generator in the rain.

• Do not alter the construction of the generator or change

controls which might create an unsafe operating condition.

• Never start or stop the unit with electrical loads connected

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

• Do not insert objects through unit’s cooling slots.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

Introduction

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

• On electric start models, disconnect the POSITIVE (+) battery

cable from the engine starter OR the NEGATIVE (-) battery

cable from the battery terminal, whichever is easier, before

transporting the generator.

NOTE:

This generator (CARB model) equipped with a spark arrestor

muffler. The spark arrestor must be maintained in effective

working order by the owner/ operator. In the State of

California, a spark arrestor is required by law (Section 4442

of the California Public Resources Code). Other states may

have similar laws. Federal laws apply on federal lands.

EXHAUST & LOCATION HAZARDS

• Never operate in an enclosed area or indoors! NEVER use

in the home, in a vehicle, or in partly enclosed areas such

as garages, even if doors and windows are open! ONLY use

outdoors and far from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide, which

you cannot see or smell. This poisonous gas, if breathed in

sufficient concentrations, can cause unconsciousness or even

death.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

• This exhaust system must be properly maintained. Do nothing

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

• Always use a battery operated carbon monoxide alarm indoors,

installed according to the manufacturers instructions.

• If you start to feel sick, dizzy, or weak after the generator has

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

• Never handle any kind of electrical cord or device while

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or highly

conductive area (such as metal decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged electrical

cord sets with the generator.

• Before performing any maintenance on the generator, disconnect

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

• Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.

Do not permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

• Never add fuel while unit is running or hot. Allow engine to cool

completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws regulating

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

Safety Rules

• Do not insert objects through unit’s cooling slots.

• Do not operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

• Keep a fire extinguisher near the generator at all times.

STANDARDS INDEX

In the absence of pertinent standards, codes, regulations and

laws, the published information listed below may be used as a

guideline for operation of this equipment. Always reference the

latest revision available for the standards listed.

1. NFPA No. 70, NFPA HANDBOOK OF NATIONAL ELECTRIC

CODE.

2. Article X, NATIONAL BUILDING CODE, available from the

American Insurance Association, 85 John Street, New York,

N.Y. 10038.

3. AGRICULTURAL WIRING HANDBOOK, available from the Food

and Energy Council, 909 University Avenue, Columbia, MO

65201.

4. ASAE EP-3634, INSTALLATION AND MAINTENANCE OF

FARM STANDBY ELECTRICAL SYSTEMS, available from the

American Society of Agricultural Engineers, 2950 Niles Road,

St. Joseph, MI 49085.

MODEL NO:

SERIAL NO:

Generator Identification

Safety Rules

1.1 UNPACKING

• Remove all packaging material.

• Remove separate accessory box.

• Remove carton off the generator.

1.1.1 ACCESSORY BOX

Check all contents (Figure 1). If any parts are missing or damaged

locate an authorized dealer at 1-888-436-3722.

Contents include:

• 2 – Axle Pins • Oil Filter

• 2 – Wheel Spacers • Air Filter

• 2 – Hair Pins • Spark Plug

• 2 – Wheels • Spark Plug Wrench

• 1 – Frame Foot • Shop Towel

• 2 – Frame Bolts • 2 – Frame Washers

• 2 – Vibration Mounts • Oil Funnel

• 4 – Flange Nuts 12 Volt Adaptor Plug Charger

• 2 – 1 Quart SAE 30 Oil Bottles

Figure 1 – Accessory Boxes

1.2 ASSEMBLY

Read entire Owner's Manual before attempting to assemble or

operate the generator. The generator requires some assembly

prior to using it. If problems arise when assembling the generator,

please call the Generator Helpline at 1-888-436-3722.

1.2.1 ASSEMBLING THE WHEEL KIT AND FRAME FOOT

The wheel kit is designed to greatly improve the portability of the

generator. You will need the following tools to install the wheel

kit: Pliers, 1/2" (13mm) wrench and a socket wrench with a 1/2"

(13mm) socket.

NOTE:

The wheel kit is not intended for over-the-road use.

• Refer to Figure 2 and install the wheel kit and frame foot as

follows:

• Slide the Axle Pin through the Wheel, Wheel Spacer (Washer)

and the Frame.

• Install the Hair Pin to the Axle Pin to secure the wheel. Repeat

for the opposite side.

• Secure the Vibration Mounts to the Frame Foot with the included

locking nuts.

• To install the Frame Foot, install the Frame Bolts though the

Frame Washers, Frame and Frame foot. Secure with the flange

nuts.

Figure 2 – Wheel and Foot Assembly

ASSEMBLE

FRAME

FOOT

SECURE WHEEL

AND AXLE WITH

HAIR PIN

SLIDE AXLE

THROUGH WHEEL

AND WHEEL

SPACER

WHEEL SPACER

(WASHER)

FRAME

BOLT

FRAME

WASHER

FLANGE

NUT

General Information

1.3 EMISSIONS INFORMATION

The Environmental Protection Agency (EPA) requires that

this generator comply with exhaust and evaporative emission

standards. This generator is certified to meet the applicable EPA

emission levels on gasoline. The emission control system on this

generator consists of the following:

• Fuel System • Air Induction System

~ Carburetor ~ Intake Pipe/manifold

~ Fuel Tank/cap ~ Air Filter

~ Fuel Lines

• Ignition System

~ Evaporative Vent Lines ~ Spark plug

• Exhaust System ~ Ignition module

~ Exhaust Manifold

• Exhaust System

~ Muffler ~ Exhaust Manifold

It is important to perform the service specified in the Maintenance

Schedule to ensure that the generator complies with the applicable

emission standards for the duration of its useful life. Additionally,

emissions critical maintenance must be performed as scheduled

in order for the Emissions Warranty to be valid. Emissions critical

maintenance consists of servicing the air filter and spark plugs in

accordance with the Maintenance Schedule. Service and repairs

may be performed by any capable person or repair shop.

1.4 PRODUCT SPECIFICATIONS

1.4.1 GENERATOR SPECIFICATIONS

Assembled Dimensions: (Length X Width X Height) :

800mm [31.5"] X 648mm [25.5"] X 711mm [28"]

Extended Length: 1232mm [48.5"]

Model # ......................................................................005846, 005847

Rated Max. Power ...................................................................8.0 kW**

Surge Power ................................................................................10 kW

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V .............................................................33.3 Amps**

Current @ 120V .............................................................66.7 Amps**

Rated Frequency .................................................... 60 Hz @ 3600 RPM

Phase ................................................................................Single Phase

Rated DC Voltage ...................................................................... 12 Volts

Battery Type .................................................................... 10 AH, 12VDC

Unit Weight ................................................................ 100 Kg [219 lbs.]

Model # ......................................................................005845, 005798

Rated Max. Power ...................................................................7.0 kW**

Surge Power .............................................................................8.75 kW

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V .............................................................29.2 Amps**

Current @ 120V .............................................................58.3 Amps**

Rated Frequency .................................................... 60 Hz @ 3600 RPM

Phase ................................................................................Single Phase

Rated DC Voltage ...................................................................... 12 Volts

Battery Type .................................................................... 10 AH, 12VDC

Unit Weight ................................................................ 100 Kg [219 lbs.]

Model # ....................................................................................005796

Rated Max. Power ...................................................................6.5 kW**

Surge Power .............................................................................8.13 kW

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V .............................................................27.1 Amps**

Current @ 120V .............................................................54.2 Amps**

Rated Frequency .................................................... 60 Hz @ 3600 RPM

Phase ................................................................................Single Phase

Rated DC Voltage ...................................................................... 12 Volts

Unit Weight ................................................................ 102 Kg [225 lbs.]

** Maximum wattage and current are subject to, and limited by, such factors

as fuel Btu content, ambient temperature, altitude, engine condition, etc..

Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each 6° C (10° F) above 16° C (60° F)

ambient temperature.

1.4.2 ENGINE SPECIFICATIONS

Displacement ...............................................................................407cc

Spark Plug Type ...................................Champion RC14YC or Equivalent

Spark Plug Part No. ...................................................................0E7585

Spark Plug Gap ............................................... 0.030 inch or (0.76 mm)

Gasoline Capacity ............................................................ 9 U.S. gallons

Oil Type....................................See Chart in "Adding Engine Oil" Section

Oil Capacity ................................................ w/ Filter Change = 1.5 Qts.

w/o Filter Change = 1.2 Qts.

Oil Filter Part No. . ....................................................................070185B

Run Time/Fuel Consumption-1/2 Load .. 10 Hours / .73 gallons per hour

2.1 KNOW THE GENERATOR

Read the entire Owner’s Manual and Safety Rules before

operating this generator.

Compare the generator to Figures 3 through 6 to become

familiarized with the locations of various controls and adjustments.

Save this manual for future reference.

1. Choke Knob – Used when starting a cold engine (Pull/Push).

2. Engine Switch – Controls the operation of the generator. On

electric start models the switch is Start/Run/Stop. On recoil

start models the switch is On/Off.

3. Fuel Shut Off – Valve between fuel tank and carburetor. Turn

off and run carburetor out of fuel for extended storage.

4. Panel LED's – Provide illumination of the control panel while

the generator is operating.

5. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 and/or 240 Volt AC,

30 Amp, single-phase, 60 Hz, electrical lighting, appliance,

tool and motor loads.

6. 120 Volt AC, 20 Amp, GFCI Duplex Receptacle – Supplies

electrical power for the operation of 120 Volt AC, 20 Amp,

single-phase, 60 Hz electrical lighting, appliance, tool and

motor loads. It also provides protection with an Integral

Ground Fault Circuit Interrupter, complete with a press to

"Test" and "Reset" button.

7. Circuit Breakers (AC) – Each 20 Amp receptacle is provided

with a push-to-reset circuit breaker to protect the generator

against electrical overload.

Operation

8. Circuit Breakers (AC) – The 30 Amp receptacle is protected

with a pair of push-to-reset or a 2 pole toggle circuit breaker(s)

to protect the generator against electrical overload.

9. PowerBar – Indicates the amount of power being used from

the generator; each section is approximately 25%

10. Hourmeter – Provides operating hours for Service Intervals.

11. Battery Charger Input (Electric Start Models) – This

receptacle allows the capability to recharge the 12 VDC engine

starting battery with the 12 Volt Adaptor Plug Charger. The

battery is protected by a 1.50 Amp in-line fuse which is inside

the control panel.

12. Fuel Tank – Tank holds 9 U.S. gallons of fuel.

13. Fuel Gauge – Shows fuel level in tank.

14. Handles – Pivot and retract for storage. Press the spring-

loaded button to move handles.

15. Oil Fill – Check oil level and add oil here.

16. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

17. Muffler – Includes the spark arrestor and quiets the engine.

18. Spark Plug Location – The spark plug ignites the Air/Fuel

Mixture (Side panel must be removed).

19. Engine Oil Filter – Filters engine oil; see Section 3.1 for the

proper service intervals.

20. Air Filter – Filters intake air as it is drawn into the engine.

21. Oil Drain – Drain valve to remove used oil from the engine

crankcase.

22. Recoil Starter – Use to start engine manually.

23. Roll Over Valve - Passes fuel vapors to the engine.

24. Recovery Hose - Install between roll over valve and the

engine.

25. Carbon Canister - Absorbs fuel tank vapors (CARB).

Figure 3 – Generator Locations

Operation

2.1.1 BATTERY CONNECTION

NOTE:

The battery shipped with the generator has been fully charged.

A battery may lose some of its charge when not in use for

prolonged periods of time. If the battery is unable to crank

the engine, plug in the 12V charger included in the accessory

box (see the Charging the Battery section). RUNNING THE

GENERATOR DOES NOT CHARGE THE BATTERY.

The positive battery wire was deliberately left detached for

shipping. To operate the unit, attach this wire to the terminal on

the starter motor as shown. Do not overtighten. Slide the attached

rubber boot over the starter terminal. See Figure 4.

Figure 4 – Battery Connection

ENGINE

STARTER

POSITIVE (+)

BATTERY CABLE

2.2 HOURMETER - NO RESET

The Hourmeter tracks hours of operation for scheduled

maintenance:

There will be a one time break in "CHG OIL" message that flashes

with the elapsed time in hours and tenths after the first 30 hours

of operation.

This message will actually begin flashing at 29 hours and disable

itself at 31 hours providing a two hour window to perform the

service.

There will be a subsequent "CHG OIL" message every 100 hours.

The message will flash one hour before and one hour after each

100 hour interval, again providing a two hour window to perform

service.

Every 200 hours the "SVC" icon on the lower left hand corner of

the display will flash. The message will flash one hour before and

one hour after each 200 hour interval providing a two hour window

to perform service.

When the hour meter is in the Flash Alert mode, the maintenance

message will always alternate with elapsed time in hours and

tenths. The hours will flash four times, then alternate with the

maintenance message four times until the meter resets itself.

• 100 hours - CHG OIL — Oil Change Interval (Every 100 hrs)

• 200 hours - SVC — Air Filter Interval (Every 200 hrs)

2.3 HOURMETER - WITH RESET

The Hourmeter tracks hours of operation for scheduled maintenance

(see chart) (Figure 5).

Operation: Push and release the reset button to toggle between

screens. The hours count backwards from the set interval as

shown in the chart.

When the meter reaches 5 hours,the text "CHG OIL" (or "SVC AIR

FILTER" or "CHG PLUG") will flash continually for two minutes.

After this time, the meter will go back to displaying the total hours

of the unit (for 2 minutes). This cyle will repeat for the entire 5

hours.

When the service interval reaches zero hours, the text "NOW"

replaces the hours remaining.

For a new generator for instance, the message will say "CHG OIL"

then flash "in 30". This means that in 30 hours, the oil will need to

be changed. Pressing the button a few more times will bring the

meter back to the screen that shows the total hours run.

Reset: Toggle to the alert that you wish to reset then hold the

button down for 9 seconds. The maintenance hours are reset when

the display shows "0000.0".

Note:

The hour glass graphic will flash on and off when the engine

is running. This signifies that the meter is tracking hours of

operation.

Figure 5 – Hourmeter

HOUR GLASS

GRAPHIC

RESET BUTTON

(IF EQUIPPED)

0000.0

Operation

2.4 CORD SETS AND CONNECTION PLUGS

2.4.1 120 VAC, 20 AMP, GFCI DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 20 Amp

push-to-reset circuit breaker (Figure 6). Use each socket to power

120 Volt AC, single phase, 60 Hz electrical loads requiring up to a

combined 2400 watts (2.4 kW) or 20 Amps of current. Use only

high quality, well-insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

Keep extension cords as short as possible, preferably less than

15 feet long, to prevent voltage drop and possible overheating of

wires.

2.4.2 120/240 VAC, 30 AMP RECEPTACLE

Use a NEMA L14-30 plug with this receptacle (rotate to lock/

unlock). Connect a suitable 4-wire grounded cord set to the plug

and to the desired load. The cord set should be rated for 250 Volts

AC at 30 Amps (or greater) (Figure 6).

Use this receptacle to operate 120 Volt AC, 60 Hz, single phase

loads requiring up to 3600 watts (3.6 kW) of power at 30 Amps

or 240 Volt AC, 60 Hz, single phase loads requiring 6,500 to 8000

watts of power, depending on the model. The outlet is protected by

a 30 Amp circuit breaker.

Figure 6 – Generator Receptacles

120 VAC 20A

GFCI RECEPTACLE

120/240 VAC 30A

RECEPTACLE

2.5 HOW TO USE THE GENERATOR

See the "To Start the Engine" section for how to safely start and

stop the generator and how to connect and disconnect loads. If

there are any problems operating the generator, please call the

generator helpline at 1-888-436-3722.



Never operate in an enclosed area or indoors!

NEVER use in the home, in a vehicle, or in

partly enclosed areas such as garages, EVEN

IF doors and windows are open! ONLY use

outdoors and far from open windows, doors,

vents, and in an area that will not accumulate

deadly exhaust.



The engine exhaust fumes contain carbon

monoxide, which can you cannot see or smell.

This poisonous gas, if breathed in sufficient

concentrations, can cause unconsciousness or

even death.



Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or permit

even partial blockage of ventilation provisions,

as this can seriously affect safe operation

of the generator. The generator MUST be

operated outdoors.



This exhaust system must be properly

maintained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.



Always use a battery operated carbon

monoxide alarm indoors, installed according to

the manufacturers instructions.

2.5.1 GROUNDING THE GENERATOR WHEN USED AS A

PORTABLE

This generator has an equipment ground that connects the

generator frame components to the ground terminals on the AC

output receptacles (see NEC 250.34 (A) for explanation). This

allows the generator to be used as a portable without grounding

the frame of the generator as specified in NEC 250.34.

Special Requirements

There may be Federal or State Occupational Safety and Health

Administration (OSHA) regulations, local codes, or ordinances that

apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or the

local agency having jurisdiction:

• In some areas, generators are required to be registered with

local utility companies.

• If the generator is used at a construction site, there may be

additional regulations which must be observed.

Operation

2.5.2 CONNECTING THE GENERATOR TO A BUILDING’S

ELECTRICAL SYSTEM

When connecting directly to a building's electrical system, it is

recommended that a manual transfer switch is used. Connections

for a portable generator to a building's electrical system must be

made by a qualified electrician and in strict compliance with all

national and local electrical codes and laws.

Figure 7 – Generator Ground Location

GROUND LOCATION

2.5.3 NEUTRAL TO FRAME GROUNDING

If service work is performed on the alternator, DO NOT discard

the white jumper wires from the terminal block to the alternator

ground, located on the rear bearing carrier. Always make sure

the wires are properly connected before using the generator after

alternator service work is done (Figure 8).

Figure 8 – Neutral to Frame Ground

NEUTRAL TO FRAME GROUND

DO NOT DISCARD

THESE WIRES!



Failure to reconnect these wires may create a

potential shock hazard when the generator is

running!

2.5.4 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles.

DO NOT connect 3 phase loads to the generator.

DO NOT connect 50 Hz loads to the generator.

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 or 240 Volt AC, single

phase, 60 Hz electrical loads.

• Add up the rated watts (or amps) of all loads to be connected

at one time. This total should no be greater than (a) the rated

wattage/amperage capacity of the generator or (b) circuit

breaker rating of the receptacle supplying the power. See “Don’t

Overload the Generator

2.6 DON’T OVERLOAD THE GENERATOR

Overloading a generator in excess of its rated wattage capacity

can result in damage to the generator and to connected electrical

devices. Observe the following to prevent overloading the unit:

• Add up the total wattage of all electrical devices to be connected

at one time. This total should NOT be greater than the

generator's wattage capacity.

• The rated wattage of lights can be taken from light bulbs. The

rated wattage of tools, appliances and motors can usually be

found on a data label or decal affixed to the device.

• If the appliance, tool or motor does not give wattage, multiply

volts times ampere rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction types, require about

three times more watts of power for starting than for running.

This surge of power lasts only a few seconds when starting

such motors. Make sure to allow for high starting wattage when

selecting electrical devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other connected

loads.

The Wattage Reference Guide is provided to assist in determining

how many items the generator can operate at one time.

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with push-to-reset-type circuit breakers. Read “Don’t

Overload the Generator” carefully.

NOTE:

All figures are approximate. See data label on appliance for

wattage requirements.

Operation

2.7 WATTAGE REFERENCE GUIDE

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9"). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

Electric Skillet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

*Freezer . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875

*Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 to 750

Hair Dryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 to 1100

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Lawn Mower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Microwave Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700 to 1000

*Milk Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . 400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . 600

Paint Sprayer, Airless (handheld). . . . . . . . . . . . . . . . . . . . . . . . . 150

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 to 200

*Refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

Slow Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . 2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Submersible Pump (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1750 to 2000

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 to 500

Toaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 to 1650

Weed Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

* Allow 3 times the listed watts for starting these devices.

2.8 BEFORE STARTING THE GENERATOR

Prior to operating the generator, engine oil and gasoline will need

to be added, as follows:

2.8.1 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Use no special additives. Select

the oil's viscosity grade according to the expected operating

temperature (also see chart).

• Above 40° F, use SAE 30

• Below 40° F and down to 10° F, use 10W-30

• Synthetic 5W-30, for all temperature ranges



Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil may

result in an engine failure.

• Place generator on a level surface (not to exceed 15° in any

direction).

• Clean area around oil fill and remove oil fill cap.

• Slowly fill engine with oil through the oil fill opening until it

reaches the full mark. Stop filling occasionally to check oil level.

(Engine oil is full when level is up to the threads of the oil fill

plug, see Figure 9.)

• Install oil fill cap and finger tighten securely.

• Check engine oil level before starting each time thereafter.

Operation

Figure 9 – Oil Level

2.8.2 ADDING GASOLINE





DO NOT light a cigarette or smoke when filling the fuel

tank.



Never fill fuel tank indoors. Never fill fuel tank when

engine is running or hot. Avoid spilling gasoline on a hot

engine. Allow engine to cool entirely before filling fuel

tank.





Do not overfill the fuel tank. Always leave room for fuel

expansion. If the fuel tank is overfilled, fuel can overflow

onto a hot engine and cause FIRE or EXPLOSION. Wipe

up any spilled fuel immediately.

• Use regular UNLEADED gasoline with the generator engine. Do

not mix oil with gasoline.

• Do not use gasoline with more than 10% alcohol such as E85

or Methanol.

• Clean area around fuel fill cap, remove cap.

• Slowly add unleaded regular gasoline to fuel tank. Be careful

not to overfill (Figure 10).

• Install fuel cap and wipe up any spilled gasoline.

Figure 10 – Fuel Fill Level

DO NOT FILL

ABOVE LIP!

IMPORTANT: It is important to prevent gum deposits from forming

in fuel system parts such as the carburetor, fuel hose or tank

during storage. Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or

longer. See the "Storage" section. Never use engine or carburetor

cleaner products in the fuel tank as permanent damage may occur.

2.9 TO START THE ENGINE

Never start or stop engine with electrical devices plugged into

the receptacles AND devices turned on.

• Unplug all electrical loads from the unit's receptacles before

starting the engine.

• Make sure the unit is in a level position (not to exceed 15° in

any direction).

• Open the fuel shut-off valve (Figure 11).

• Pull engine CHOKE knob outward to “Full Choke” position

(Figure 12).

Figure 11 – Fuel Shut-off Valve

Figure 12 – Choke Operation

Operation

2.9.1 MANUAL (RECOIL) STARTING

• To start the generator, put the on/off switch in the ON position.

• Firmly grasp the recoil handle and pull slowly until increased

resistance is felt. Pull rapidly up and away to start engine.

• When the engine starts, push choke knob to “1/2 Choke”

position until the engine runs smoothly and then fully in to the

“Run” position. If engine falters, pull choke knob back out to

“1/2 Choke” position until the engine runs smoothly and then

to “Run” position.

NOTE:

If engine fires, but does not continue to run, pull choke knob

to “Full Choke” and repeat starting instructions.

2.9.2 ELECTRIC STARTING

• To start the engine, press and hold the Start/Run/Stop switch in

the “Start” position. The engine will crank and attempt to start.

When the engine starts, release the switch to the run position.

• When the engine starts, push choke knob to “1/2 Choke”

position until the engine runs smoothly and then fully in to the

“Run” position. If engine falters, pull choke knob back out to

“1/2 Choke” position until the engine runs smoothly and then

to “Run” position.

• This generator is also equipped with a manual recoil starter

which may be used if the battery is discharged.

NOTE:

The switch must be in the RUN position. Use one of the

generator’s receptacle outlets along with the included battery

charger to charge the battery while the generator is running.

2.10 STOPPING THE ENGINE

• Shut off all loads, then unplug the electrical loads from generator

panel receptacles. Never start or stop the engine with electrical

devices plugged in and turned on.

• Let engine run at no-load for several minutes to stabilize the

internal temperatures of engine and generator.

• Move Start/Run/Stop or On/Off switch to the “Off” position.

• Close fuel valve.

2.11 LOW OIL PRESSURE SHUTDOWN SYSTEM

The engine is equipped with a low oil pressure sensor that shuts

down the engine automatically when the oil pressure drops below

5 psi. A delay built into the low oil shutdown system allows oil

pressure to build during starting. The delay allows the engine to

run for about 10 seconds before sensing oil pressure. If the engine

shuts down by itself and the fuel tank has enough gasoline, check

engine oil level.

2.11.1 RESTARTING

If trying to restart the engine within 10 seconds after it shuts down,

the engine may NOT start. The system needs 5 to 10 seconds to

reset.

If the engine is restarted after such a shutdown and the low oil

pressure has not been corrected, the engine will run for about 10

seconds as described above and then stop.

2.12 CHARGING THE BATTERY



Do not permit smoking, open flame, sparks or

any other source of heat around a battery. Wear

protective goggles, rubber apron and rubber

gloves when working around a battery. Battery

electrolyte fluid is an extremely corrosive

sulfuric acid solution that can cause severe

burns. If spill occurs flush area with clear water

immediately.





Storage batteries give off explosive hydrogen

gas while recharging. An explosive mixture will

remain around the battery for a long time after

it has been charged. The slightest spark can

ignite the hydrogen and cause an explosion.

Such an explosion can shatter the battery and

cause blindness or other serious injury.

Use battery charger plug to keep the battery charged and ready

for use. Battery charging should be done in a dry location.

1. Plug charger into “Battery Charger Input” jack, located on the

control panel. Plug wall receptacle end of the battery charger

into a 120 Volt AC wall outlet.

2. Unplug battery charger from wall outlet and control panel jack

when generator is going to be in use.

NOTE:

Do not use the battery charger for more than 48 hours at one

charge.

Operation

3.1 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required

when operating in adverse conditions noted below.

Check Oil Level At Each Use

Change Oil and Oil Filter‡ *Every Season/Every 100 Hours

Clean Spark Arrestor Screen **Every Season/Every 100 Hours

Service Air Filter **Every Season/Every 200 Hours

Replace Spark Plug Every Season

‡ Change oil after first 30 hours of operation then every season.

* Change oil and oil filter every month when operating under heavy load or in

high temperatures.

** Clean more often under dirty or dusty operating conditions. Replace air filter

parts if very dirty.

3.2 GENERAL RECOMMENDATIONS

The warranty of the generator does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly

maintain the generator.

All adjustments in the Maintenance section of this manual should

be made at least once each season. Follow the requirements in the

"Maintenance Schedule".

NOTE:

Once a year replace the spark plug and replace the air filter.

A new spark plug and clean air filter assure proper fuel-air

mixture and help the engine run better and last longer.

3.2.1 GENERATOR MAINTENANCE

Generator maintenance consists of keeping the unit clean and dry.

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors. Cooling air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.



Never insert any object or tool through the air cooling

slots, even if the engine is not running.

NOTE:

DO NOT use a garden hose to clean generator. Water can

enter the engine fuel system and cause problems. In addition,

if water enters the generator through cooling air slots, some

water will be retained in voids and crevices of the rotor

and stator winding insulation. Water and dirt buildup on the

generator internal windings will eventually decrease the

insulation resistance of these windings.

3.2.2 TO CLEAN THE GENERATOR

• Use a damp cloth to wipe exterior surfaces clean.

• A soft, bristle brush may be used to loosen caked on dirt, oil, etc.

• A vacuum cleaner may be used to pick up loose dirt and debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and openings on the

generator. These openings must be kept clean and unobstructed.

3.2.3 ENGINE MAINTENANCE



When working on the generator, always disconnect

negative cable from battery. Also disconnect spark plug

wire from spark plug and keep wire away from spark

plug.

3.2.4 CHECKING OIL LEVEL

See the “BEFORE STARTING THE GENERATOR” section for

information on checking the oil level. The oil level should be

checked before each use, or at least every eight hours of operation.

Keep the oil level maintained.

3.2.5 CHANGING THE OIL AND OIL FILTER

Change the oil and filter after the first 30 hours of operation.

Change the oil every 100 hours or every season thereafter. If

running this unit under dirty or dusty conditions, or in extremely

hot weather, change the oil more often.



Hot oil may cause burns. Allow engine to cool before

draining oil. Avoid prolonged or repeated skin exposure

with used oil. Thoroughly wash exposed areas with soap.

Use the following instructions to change the oil:

• Clean area around oil drain cap.

• Remove oil drain cap from the drain hose and oil fill plug to drain

oil completely into a suitable container.

• When oil has completely drained, install oil drain cap and tighten

securely.

• Place a suitable container beneath the oil filter and turn

filter counterclockwise to remove. Discard according to local

regulations.

Maintenance

• Coat gasket of new filter with clean engine oil. Turn filter

clockwise until gasket contacts lightly with filter adapter. Then

tighten an additional 3/4 turn.

• Fill oil sump with recommended oil and replace the oil fill plug.

(See “Before Starting the Generator” for oil recommendations).

• Wipe up any spilled oil.

• Dispose of used oil at a proper collection center.

3.2.6 REPLACING THE SPARK PLUG

Use Champion RC14YC spark plug or equivalent. Replace the

plug once each year. This will help the engine start easier and

run better.

1. Stop the engine and pull the spark plug wire off of the spark

plug.

2. To gain access, remove the four (4) socket head screws and

take off the side panel.

3. Clean the area around the spark plug and remove it from the

cylinder head.

4. Set the spark plug's gap to .76 mm (0.030 in.). Install the

correctly gapped spark plug into the cylinder head (Figure 13).

5. Push the boot firmly on the spark plug and install side panel.

Figure 13 – Spark Plug Gap

3.3 SERVICE AIR FILTER

The engine will not run properly and may be damaged if using a

dirty air filter. Clean or replace the air filter paper filter every 200

hours or once a year (Figure 14). Clean or replace more often if

operating under dusty conditions. To clean or replace paper air

filter:

• Remove air filter cover and remove paper filter (Figure 14).

• Clean paper filter by tapping it gently on a solid surface. If the

filter is too dirty, replace it with a new one. Dispose of the old

filter properly.

• Clean air filter cover. Next insert new paper filter into the base

of the air filter. Re-install air filter cover.

NOTE:

To order a new air filter, please contact the nearest authorized

service center at 1-888-GENERAC. The air filter part number

is 073111.

Figure 14 – Air Filter

AIR FILTER

COVER

3.4 CLEAN SPARK ARRESTOR SCREEN

The engine exhaust muffler has a spark arrestor screen. (CARB

only) Inspect and clean the screen at least once each year (Figure

15). If unit is used regularly, inspect and clean more often.



If using the generator on any forest-covered,

brush-covered or grass-covered unimproved

land, it must equipped with a spark arrestor.

The spark arrestor must be maintained in good

condition by the owner/operator.

Clean and inspect the spark arrestor when the engine is at ambient

temperature as follows:

• Loosen the clamp and remove the spark arrestor screen from

the muffler.

• Inspect screen and replace if torn, perforated or otherwise

damaged. DO NOT USE a defective screen. If screen is not

damaged, clean it with commercial solvent.

• Replace the spark arrestor and secure with the clamp.

Figure 15 – Spark Arrestor Screen

CONE

SCREEN

CLAMP

MUFFLER

Maintenance

3.5 ADJUSTING VALVE CLEARANCE

After the first 50 hours of operation, check the valve clearance

in the engine and adjust if necessary.

Important: If feeling uncomfortable about doing this procedure or

the proper tools are not available, please take the generator to the

nearest service center to have the valve clearance adjusted. This is

a very important step to insure longest life for the engine.

To check valve clearance:

1. Make sure the engine is at room temperature (60° - 80° F).

2. Make sure that the spark plug wire(s) is removed from the

spark plug and out of the way. Remove spark plug(s).

3. Remove the four screws attaching the valve cover(s).

4. Make sure the piston is at Top Dead Center (TDC) of its

compression stroke (both valves closed). To get the piston

at TDC, remove the intake screen at the front of the engine to

gain access to the flywheel nut. Use a large socket and socket

wrench to rotate the nut and hence the engine in a clockwise

direction while watching the piston through the spark plug

hole. The piston should move up and down. The piston is at

TDC when it is up as high as it can go.

5. Insert a 0.002 - 0.004 inch (0.05 - 0.1mm) feeler gauge

between the rocker arm and valve stem. Correct clearance

is when a slight drag is felt when sliding the gauge back and

forth. If the clearance is either excessively loose or tight the

rocker arms will need adjusting.

To adjust valve clearance:

1. Loosen the rocker jam nut (Figure 27). Use an 8mm allen

wrench for the 3.6kW/10kW and 10mm allen wrench for

the 6.5kW/8kW to turn the pivot ball stud, while checking

clearance between the rocker arm and the valve stem with a

feeler gauge. Correct clearance is 0.002-0.004 inch (0.05-0.1

mm).

NOTE:

The rocker arm jam nut must be held in place as the pivot ball

stud is turned.

When valve clearance is correct, hold the pivot ball stud in

place with the allen wrench (10mm for 3.6kW/10kW, 13mm for

6.5kW/8kW) and tighten the rocker arm jam nut. Tighten the jam

nut to 174 in/lbs. torque. After tightening the jam nut, recheck

valve clearance to make sure it did not change.

2. Install new valve cover gasket.

3. Re-attach the valve cover.

NOTE:

Start all four screws before tightening or it will not be possible

to get all the screws in place. Make sure the valve cover

gasket is in place. Replace spark plug(s).

4. Re-attach the spark plug wire(s) to the spark plug(s).

5. Repeat steps for cylinder #2 on 10kW units.

Figure 27 - Valve Clearance Adjustment

3.6 GENERAL

The generator should be started at least once every 30 days and

be allowed to run at least 30 minutes. If this cannot be done and

the unit must be stored for more than 30 days, use the following

information as a guide to prepare it for storage.





NEVER store engine with fuel in tank indoors

or in enclosed, poorly ventilated areas where

fumes may reach an open flame, spark or pilot

light as on a furnace, water heater, clothes

dryer or other gas appliance.



Allow unit to cool entirely before storage.

3.7 LONG TERM STORAGE

It is important to prevent gum deposits from forming in essential

fuel system parts such as the carburetor, fuel hose or tank during

storage. To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer, as follows:

• Remove all gasoline from the fuel tank.



Drain fuel into approved container outdoors, away from

open flame. Be sure engine is cool. Do not smoke in the

vicinity or light a cigarette.

• Start and run engine until engine stops from lack of fuel.

• Allow the engine to cool, then drain oil from crankcase. Refill

with recommended grade.

• Remove spark plug and pour about 1/2 ounce (15 ml) of engine

oil into the cylinder. Cover spark plug hole with rag. Pull the

recoil starter a couple times to lubricate the piston rings and

cylinder bore.

Maintenance



Avoid spray from spark plug hole when

cranking engine.

• Install and tighten spark plug. Do not connect the spark plug

wire.

• Clean the generator outer surfaces. Check that cooling air slots

and openings on generator are open and unobstructed.

• Store the unit in a clean, dry place.

3.8 OTHER STORAGE TIPS

• Do not store gasoline from one season to another.

• Replace any gasoline can that starts to rust. Rust and/or dirt in

the gasoline will cause problems with the carburetor and fuel

system.

• If possible, store the unit indoors and cover it to give protection

from dust and dirt. Cover the unit with a suitable protective

cover that does not retain moisture.

• BE SURE TO EMPTY THE FUEL TANK. If it is not practical

to empty the fuel tank and the unit is to be stored for some

time, use a commercially available fuel stabilizer added to the

gasoline to increase the life of the gasoline.



NEVER cover the generator while engine and

exhaust area are warm.

4.1 BATTERY REPLACEMENT

NOTE:

The battery shipped with the generator has been fully charged.

A battery may lose some of its charge when not in use for

prolonged periods of time. If the battery is unable to crank

the engine, plug in the 12V charger included in the accessory

box (see the Charging a Battery section). RUNNING THE

GENERATOR DOES NOT CHARGE THE BATTERY.

The battery shipped with the generator has been provided fully

charged. To replace the battery (See Figure 16):

• Remove the side panel as shown. Remove the four bolts

securing the fuel tank.

• Turn the fuel valve on the control panel to the "OFF" position. Pull

the fuel tank back slightly and remove the fuel hose that runs

from the engine to the fuel valve.



Drain fuel into approved container outdoors, away from

open flame. Be sure engine is cool. Do not smoke in the

vicinity or light a cigarette.

• Disconnect the recovery hose from the rollover valve. Push the

hose through the grommet in the corner of the fuel tank. This

will allow for removal of the fuel tank.

• Push the fuel valve from the control panel and remove the fuel

tank.

• Remove the battery wire connections (black wire first) and the

battery hold-down bracket.

• Replace the battery, connecting the RED wire to the POSITIVE

(+) terminal and the BLACK wire to the NEGATIVE (-) terminal

NOTE:

Start all four screws on the side panel before tightening or it

may not be possible to get all the screws in place.

Figure 16 – Battery Removal

FUEL TANK

ASSEMBLY

ENGINE

STARTING

BATTERY

BRACKET

SIDE

PANEL

Battery Service

PROBLEM CAUSE CORRECTION

Engine is running, but no AC output

is available.

1. Circuit breaker is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Fault in generator.

5. GFCI trips the 20 Amp outlet.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in good condition.

4. Contact Authorized Service Facility.

5. Repair the "short" and reset the GFCI.

Engine runs good but bogs down

when loads are connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See “Don’t Overload the Generator” .

3. Contact Authorized Service Facility.

4. Contact Authorized Service Facility.

Engine will not crank. 1. Battery weak or dead. 1. Recharge or replace battery (see "No Battery

Charger DC output" at bottom of guide).

2. Start engine manually using recoil starter.

Engine will not start; or starts and

runs rough.

1. Fuel shut-off is OFF.

2. Dirty air filter.

3. Out of gasoline.

4. Stale gasoline.

5. Spark plug wire not connected to spark plug.

6. Bad spark plug.

7. Water in gasoline.

8. Over-choking.

9. Low oil level.

10. Excessive rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Turn Fuel shut-off ON.

2. Clean or replace air filter.

3. Fill fuel tank.

4. Drain fuel tank and fill with fresh fuel.

5. Connect wire to spark plug.

6. Replace spark plug.

7. Drain fuel tank; fill with fresh fuel.

8. Put choke knob to No Choke position.

9. Fill crankcase to proper level.

10. Contact Authorized Service Facility.

11. Contact Authorized Service Facility.

12. Contact Authorized Service Facility.

Engine shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

3. Fault in engine.

1. Fill fuel tank.

2. Fill crankcase to proper level.

3. Contact Authorized Service Facility.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

1. See “Don’t Overload the Generator”.

2. Replace air filter.

3. Contact Authorized Service Facility.

Engine “hunts” or falters. 1. Choke is opened too soon.

2. Carburetor is running too rich or too lean.

1. Move choke to halfway position until engine runs

smoothly.

2. Contact Authorized Service Facility.

No Battery Charger DC output. 1. Battery posts are corroded.

2. Battery cable is bad.

3. Battery is defective.

4. Receptacle is bad.

5. Battery Charger in-line fuse (1.5A) melted open.

1. Clean battery posts.

2. Replace cable.

3. Check battery condition; replace if defective.

4. Contact Authorized Service Facility.

5. Replace fuse with identical 1.5A replacement fuse

only (located inside control panel).

5.1 TROUBLESHOOTING GUIDE

Troubleshooting

Manual Part No. 0K2577 Revision A (05/06/13) Printed in U.S.A.

La page est en cours de chargement...

Generac XG8000E 0058462 Manuel utilisateur

Marque: Generac

Modèle: XG8000E 0058462

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac XG8000E 0058462 User manual
español: Generac XG8000E 0058462 Manual de usuario