United States Stove AC2000 Le manuel du propriétaire
- Catégorie
- Poêle à bois
- Taper
- Le manuel du propriétaire
SAVE THESE INSTRUCTIONS
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU
TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
MODEL: AC2000
Owner’s Operation and Instruction Manual
United States Stove Company
227 Industrial Park Road
P.O. Box 151
South Pittsburg, TN 37380
SAFETY NOTICE:
If this heater is not properly installed, a house re
may result. For your safety, follow the installation
instructions. Never use make-shift compromises
during the installation of this heater. Contact local
building or re ofcials about permits, restrictions
and installation requirements in your area.
CAUTION!
Please read this entire manual before you
install or use your new room heater. Failure
to follow instructions may result in property
damage, bodily injury, or even death.
Improper Installation Could Void
Your Warranty!
Certied to: UL 1482 and Certied to: ULC-S627-00
Mobile home approved (U.S. ONLY)
U.S. Environmental Protection Agency
Certied to comply with 2015 particulate
emissions standards.
852087H-1605H
-2-
OPTIONAL ACCESSORIES
DESCRIPTION PART #
Outside Air Intake Kit 50FAK
CONGRATULATIONS!
You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.
By heating with wood you’re helping to CONSERVE ENERGY!
Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least
one tree each year. Future generations will thank you.
The instructions pertaining to the installation of your wood stove comply with UL-1482 and ULC-S627 standards.
This manual describes the installation and operation of the Ashley, AC2000 wood heater. This heater meets the
2015 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2015.
Under specic test conditions this heater has been shown to deliver heat at rates ranging from 11,817 to 31,713
Btu/hr.
Note: The BTU ratings mentioned above are based on the EPA test protocol burning dimensional Douglas Fir
lumber. Our advertised BTU’s are based on the rst hour of operation at high burn rate burning cordwood.
CAUTIONS:
• Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.
• Do not use chemicals or uids to ignite the re.
• Do not leave the stove unattended when the door is slightly opened.
• Do not burn garbage, ammable uid such as gasoline, naphtha or motor oil.
• Do not connect to any air distribution duct or system.
• Always close the door after the ignition.
Combustible : Wood
Colors : Metallic Black
Flue Pipe Diameter : 6” (152.5mm)
Flue Pipe Type: (Standard Single Wall or
Double Wall):
Black or Blued Steel 2100°F (650°C)
Minimum Chimney Hieght : 12’ (3.7m)
Maximum Log Length : 21” (533.5mm)
Dimensions
Overall :
Depth x Width x Height :
22” x 30” x 31.25” (559mm x 762mm x 794mm)
Combustion Chamber :
Width x Depth :
22 3/4” x 12” (578mm x 305mm)
Volume :
Cubic Feet:
1.86 ft³ (.0527m³)
Door Opening : Width x Height: 16” x 8” (406.5mm x 203mm)
Pyroceramic Glass Door : (Viewing) Width x
Height:
13 13/16” x 8 3/8” (351mm x 213mm)
Note: Register your product on line at www.usstove.com. See “Limited Warranty” section for specic warranty
information for your new purchase. Save your receipt with your records for any claims.
-3-
TOOLS AND MATERIALS NEEDED FOR INSTALLATION
You will need a drill with a 1/8” bit to install sheet metal screws
into connector pipe. A 5/16” socket/wrench or screw driver to
install pedestal trim, room air deector, and blower assembly
described below. A 1/2” socket/wrench to install ue collar. A
non-combustible oor protector as specied in this manual. All
chimney and chimney connector components required for your
particular chimney installation. For mobile homes, see page 13.
Assembly
Flue Collar Assembly:
1. Mount the ue collar to the top of the unit as shown using
the (3) 5/16-18 x 1-1/2 bolts, (3) washers, and (3) weld tabs
provided in the parts box.
Room Air Deector Assembly:
1. Locate the Room Air Deector. Using the three(3) 1/2 Tek
Screws provided, mount the deector to the unit as shown in
the diagram.
Firebrick Conguration:
1. Replace the Firebrick as shown in the illustration below.
Brick Conguration
Side view of ue collar
mount to heater top
HEATER
TOP
WELD
TAB
5/16-18 x 1-1/2
BOLT
SECTION A-A
SCALE .1
1
1
2
2
3
3
4
4
A A
B B
TOLERANCES
EXCEPT
AS
NOTED
HOLES
.005"
DECIMAL
.XX = 0.03 XXX = 0.010
ANGULAR
2
DESCRIPTION
FINISH
REFERENCE
SCALE
DWN BY
DATE
SIZE
REV
TITLE NUMBER
UNITED STATES STOVE COMPANY
ESTABLISHED 1869
ASHLEY CAST HEATER AC2000
AB
AC2000
TOP ASSEMBLY
WHO
6/18/2013
1
OF 3
SHEET
© 2010 United States Stove Company
ALL RIGHTS RESERVED
THE DATA CONTAINED HEREIN IS PROPRIETARY TO U. S.
STOVE COMPANY. THIS DATA SHALL NOT BE DUPLICATED,
TRANSFERRED, MADE AVAILABLE, OR USED BY ANY THIRD
PARTY FOR ANY PURPOSE EXCEPT SPECIFICALLY
AUTHORIZED IN WRITING BY U. S. STOVE COMPANY.
GENERAL NOTES:
ALL FORMED DIMENSIONS ARE TO
THE OUTSIDE OF THE PART,
UNLESS SPECIFIED OTHERWISE.
A A
REVISION HISTORY
REV DESCRIPTION DATE BY
A INITIAL RELEASE
Date
Who?
ASSEMBLY INSTRUCTIONS
Blower Assembly
THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE
SOURCE OF ELECTRICAL SUPPLY BEFORE ATTEMPTING THE
INSTALLATION.
THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE
THAT IS MARKED TO INDICATE SUCH USE.
DO NOT ROUTE THE SUPPLY CORD NEAR OR ACROSS HOT
SURFACES!
Step 1.
Fix the assembly to the back of the stove with the four screws
provided.
ASH PAN ASSEMBLY
Remove ash pan from rebox. Under the rebox, there are two
brackets; Slide the ash pan into these brackets.
NOMENCLATURES DES PIÈCES
QTÉ
TITRE
No DE PIÈCE
ARTICLE
1GOUPILLE CYLINDRIQUE 3/8 x 1-1/4 835061
4
10-24 X 3/8 po PH PN HD MS 832022
4
RONDELLE PLATE 7/32 po DI x 1/2 po DE x 3/64
832783
5 pi
JOINT D'ÉTANCHÉITÉ DE CORDON 5/8 po
880664
1VERRE DE PORTE (40564) 891813
5
4 pi
JOINT D'ÉTANCHÉITÉ, FENÊTRE, 125 x 1 L/PSA
880876
2SUPPORT, VERRE DU BAS25465
7
1
PORTE, RECTANGULAIRE, GRANDE
405698
AR
SCELLANT, SILICONE, NOIR
892849
1
POIGNÉE DE PORTE PEINTE
2569210
10
LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE
DOIVENT SE RENCONTRER AU BAS ET AU CENTRE DU VERRE.
C LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE DOIVENT
SE RENCONTRER ENTRE LES PATTES D'ARTICULATION.
1
8
4 9
6
5
3
2
7
NOMENCLATURES DES PIÈCES
QTÉ
TITRE
No DE PIÈCE
ARTICLE
1GOUPILLE CYLINDRIQUE 3/8 x 1-1/4 835061
4
10-24 X 3/8 po PH PN HD MS 832022
4
RONDELLE PLATE 7/32 po DI x 1/2 po DE x 3/64
832783
5 pi
JOINT D'ÉTANCHÉITÉ DE CORDON 5/8 po
880664
1VERRE DE PORTE (40564) 891813
5
4 pi
JOINT D'ÉTANCHÉITÉ, FENÊTRE, 125 x 1 L/PSA
880876
2SUPPORT, VERRE DU BAS25465
7
1
PORTE, RECTANGULAIRE, GRANDE
405698
AR
SCELLANT, SILICONE, NOIR
892849
1
POIGNÉE DE PORTE PEINTE
2569210
10
LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE
DOIVENT SE RENCONTRER AU BAS ET AU CENTRE DU VERRE.
C LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE DOIVENT
SE RENCONTRER ENTRE LES PATTES D'ARTICULATION.
1
8
4 9
6
5
3
2
7
-4-
Installation
SAFETY NOTICE
• If this stove is not properly installed, a house re may result. To reduce the risk of re, follow the installation
instructions.
• Consult your municipal building department or re ofcials about permits, restrictions and installations
requirements in your area.
• Use smoke detectors in the room where your stove is installed.
• Keep furniture and drapes well away from the stove.
• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid, or similar liquids to start or
“freshen up” a re in this heater. Keep all such liquids well away from the heater while it is in use.
• In the event of a chimney re, push the air control full closed to deprive the re of oxygen. Call the re
department.
• Do not connect to any air distribution duct or system.
• A source of fresh air into the room or space heated shall be provided when required.
POSITIONING THE STOVE
It is very important to position the wood stove as close as possible to the chimney, and in an area that will favor
the most efcient heat distribution possible throughout the house. The stove must therefore be installed in the
room where the most time is spent, and in the most spacious room possible. Recall that wood stoves produce
radiating heat, the heat we feel when we are close to a wood stove. A wood stove also functions by convection,
that is through the displacement of hot air accelerated upwards and its replacement with cooler air. If necessary,
the hot air distribution from the stove may be facilitated by the installation of a blower.
The wood stove must not be hooked up to a hot air distribution system since an excessive accumulation of heat
may occur. A wood stove must never be installed in a hallway or near a staircase, since it may block the way in
case of re or fail to respect required clearances.
FLOOR PROTECTOR
Your wood stove should be placed on a 1 inch, non-combustible surface with a k factor of 0.84. For multiple
layers, add R-values of each layer to determine the overall R-value. The R value for the required board is 1.03. If
there is a horizontal section of chimney connector, the oor protector should go under it and 2 inches beyond
each side To calculate R-Values for alternative methods, see “Alternate Floor Protector Calculations” section in
this manual.
The oor protector should exceed the stove as follows:
Dimension Inch mm
H ** Front 16 635
J** Left 6 153
K** Right 6 153
L** Back 1 25
M Total Width 46 1169
N Total Length 53.5 1359
* Canadian installations require 18” (457mm)
** Canadian installations require 8” (203mm)
-5-
CLEARANCES TO COMBUSTIBLES
It is of utmost importance that the clearances to combustible materials be strictly adhered to during installation
of the stove. Refer to the tables below:
• Floor to ceiling height must be at least 7’ (2.13m) in all cases.
• Do not place any combustible material within 4’ (1.2m) of the front of the unit.
• The clearance between the ue pipe and a wall are valid only for vertical walls and for vertical ue pipe.
• The chimney connector must not pass through an attic or roof space, closet or similar concealed space, a
oor, or a ceiling.
• For Canadian installations, where passage through a wall, or partition of combustible construction is desired,
the installation must conform to CAN/CSA-B365.
• A ue pipe crossing a combustible wall must have a minimum clearance of 18” (457.2mm).
• To reduce ue clearances from combustible materials, contact your local safety department.
Dimension Inch mm
A Backwall to Stove 16 406
B Sidewall to Stove 18 457
C
Wall to corner (Angled
Installation)
12 305
D Backwall to Flue 21.5 546
E Sidewall to Flue 30 762
F
Wall to Flue (Angled
Installation)
24 610
-6-
CHIMNEY CONNECTOR (STOVE PIPE)
Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the
case, we recommend you contact your dealer in order to insure there will be no problem with the draft.
The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021” or 0.53 mm. It is
strictly forbidden to use galvanized steel.
Your smoke pipe should be assembled in such a way that the male section (crimped end) of the pipe faces
down. Attach each of the sections to one another with three equidistant metal screws.
The pipe must be short and straight. All sections installed horizontally must slope at least 1/4 inch per foot, with
the upper end of the section toward the chimney. Any installation with a horizontal run of chimney pipe must
conform to NFPA 211. You may contact NFPA (National Fire Protection Association) and request the latest edition
of the NFPA Standard 211.
To insure a good draft, the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m to 3.04 m).
(Except for cases of vertical installation, cathedral-roof style where the smoke exhaust system can be much
longer and connected without problem to the chimney at the ceiling of the room).
There should never be more than two 90 degrees elbows in the smoke exhaust system.
Installation of a “barometric draft stabilizer” (replace register) on a smoke exhaust system is prohibited.
Furthermore, installation of a draft damper is not recommended. Indeed, with a controlled combustion wood
stove, the draft is regulated upon intake of the combustion air in the stove and not at the exhaust.
-7-
CHIMNEY
Your wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a factory built
chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT (2100°F). It is extremely
important that it be installed according to the manufacturer’s specications. Take into account the chimney’s
location to insure it is not too close to neighbors or in a valley which may cause unhealthy or nuisance conditions.
If you are using a masonry chimney, it is important that it be built in compliance with the specications of the
National Building Code. It must be lined with re clay bricks, metal or clay tiles sealed together with re cement.
(Round ues are the most efcient).
The interior diameter of the chimney ue must be identical to the stove smoke exhaust. A ue which is too
small may cause draft problems, while a large ue favours rapid cooling of the gas, and hence the build-up of
creosote and the risk of chimney res. Note that it is the chimney and not the stove which creates the draft effect;
your stove’s performance is directly dependent on an adequate draft from your chimney.
The following recommendations may be useful for the installation of your chimney:
1. Do not connect this unit to a chimney ue serving another appliance.
2. It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.
3. The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m) distance by a
height of 2’ (0.6m).
4. Installation of an interior chimney is always preferable to an exterior chimney. Indeed, the interior chimney
will, by denition, be hotter than an exterior chimney, being heated up by the ambient air in the house.
Therefore the gas which circulates will cool more slowly, thus reducing the build-up of creosote and the risk
of chimney res.
5. The draft caused by the tendency for hot air to rise will be increased with an interior chimney.
6. Using a re screen at the extremity of the chimney requires regular inspection in order to insure that it is not
obstructed thus blocking the draft, and it should be cleaned when used regularly.
-8-
FACTORY BUILT CHIMNEY
When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You
must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through
and “T” section package, restops (where needed), insulation shield, roof ashing, chimney cap, etc. Maintain
proper clearance to the structure as recommended by the manufacturer. The chimney must be the required
height above the roof or other obstructions for safety and proper draft operation.
-9-
MASONRY CHIMNEY
Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA)
by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration
and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the
stove through a combustible wall to a masonry chimney, special methods are needed.
-10-
Method A. 12” (304.8 mm) Clearance to Combustible Wall
Member: Using a minimum thickness 3.5” (89 mm) brick and a
5/8” (15.9 mm) minimum wall thickness clay liner, construct a
wall pass-through. The clay liner must conform to ASTM C315
(Standard Specication for Clay Fire Linings) or its equivalent.
Keep a minimum of 12” (304.8 mm) of brick masonry between
the clay liner and wall combustibles. The clay liner shall run
from the brick masonry outer surface to the inner surface of the
chimney ue liner but not past the inner surface. Firmly grout or
cement the clay liner in place to the chimney ue liner.
Method B. 9” (228.6 mm) Clearance to Combustible Wall
Member: Using a 6” (152.4 mm) inside diameter, listed, factory-
built Solid-Pak chimney section with insulation of 1” (25.4 mm)
or more, build a wall pass-through with a minimum 9” (228.6
mm) air space between the outer wall of the chimney length
and wall combustibles. Use sheet metal supports fastened
securely to wall surfaces on all sides, to maintain the 9” (228.6
mm) air space. When fastening supports to chimney length,
do not penetrate the chimney liner (the inside wall of the Solid-
Pak chimney). The inner end of the Solid-Pak chimney section
shall be ush with the inside of the masonry chimney ue, and
sealed with a non-water soluble refractory cement. Use this
cement to also seal to the brick masonry penetration.
Method C. 6” (152.4 mm) Clearance to Combustible Wall
Member: Starting with a minimum 24 gage (.024” [.61 mm])
6” (152.4 mm) metal chimney connector, and a minimum 24
gage ventilated wall thimble which has two air channels of 1”
(25.4 mm) each, construct a wall pass-through. There shall be a
minimum 6” (152.4) mm separation area containing berglass
insulation, from the outer surface of the wall thimble to wall
combustibles. Support the wall thimble, and cover its opening
with a 24-gage minimum sheet metal support. Maintain the 6”
(152.4 mm) space. There should also be a support sized to t
and hold the metal chimney connector. See that the supports
are fastened securely to wall surfaces on all sides. Make sure
fasteners used to secure the metal chimney connector do not
penetrate chimney ue liner.
Method D. 2” (50.8 mm) Clearance to Combustible Wall
Member: Start with a solid-pak listed factory built chimney
section at least 12” (304 mm) long, with insulation of 1” (25.4
mm) or more, and an inside diameter of 8” (2 inches [51 mm]
larger than the 6” [152.4 mm] chimney connector). Use this as a
pass-through for a minimum 24-gauge single wall steel chimney
connector. Keep solid-pak section concentric with and spaced
1” (25.4 mm) off the chimney connector by way of sheet
metal support plates at both ends of chimney section. Cover
opening with and support chimney section on both sides with
24 gage minimum sheet metal supports. See that the supports
are fastened securely to wall surfaces on all sides. Make sure
fasteners used to secure chimney ue line do not penetrate
the inner liner.
COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS
NOTES:
1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the
wall pass-through system and the chimney wall, to but not past the inner ue liner face.
2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a
oor, or ceiling.
-11-
OUTSIDE COMBUSTION AIR
Your wood stove is approved to be installed with an outside air intake which is necessary for a mobile home.
This type of installation is also required in air tight houses and houses with negative pressure problems. You can
purchase this option through your heater dealer. Make sure to specify the part number mentioned in this booklet.
Installation instructions are supplied with the air intake kit.
Outside combustion air may be required if:
1. Mobile Home Installations
2. Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-drafts occur whether or
not there is combustion present.
3. Existing fuel-red equipment in the house, such as replaces or other heating appliances, smell, do not
operate properly, suffer smoke roll-out when opened, or back-drafts occur whether or not there is combustion
present.
4. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.
5. The house is equipped with a well-sealed vapor barrier and tight tting windows and/or has any powered
devices that exhaust house air.
6. There is excessive condensation on windows in the winter.
7. A ventilation system is installed in the house.
For use in MOBILE HOMES (U. S. installations ONLY):
• Warning! Do not install in sleeping room.
• Caution! The structural integrity of the mobile home oor,
wall, and ceiling/roof must be maintained.
• Install in accordance with 24 CFR, part 3280 (HUD).
• Use a factory built chimney that complies with UL 103
standards; therefore it must be a type ht (2100°f).
• Use a spark arrester.
• The stove must be attached to the structure of the mobile
home. Use the mobile home leg fasteners to secure the
unit to the oor.
Illustration: Securing heater to the Floor.
WOODSTOVE UTILIZATION
This heater is designed to burn natural wood only. Higher efciencies and lower emissions generally result when
burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.
DO NOT BURN:
1. Garbage;
2. Lawn clippings or yard waste;
3. Materials containing rubber, including tires;
4. Materials containing plastic;
5. Waste petroleum products, paints or paint thinners,
or asphalt products;
6. Materials containing asbestos;
7. Construction or demolition debris;
8. Railroad ties or pressure-treated wood;
9. Manure or animal remains;
10. Salt water driftwood or other previously salt water
saturated materials;
11. Unseasoned wood; or
12. Paper products, cardboard, plywood, or
particleboard. The prohibition against burning
these materials does not prohibit the use of re
starters made from paper, cardboard, saw dust,
wax and similar substances for the purpose of
starting a re in an affected wood heater.
Burning these materials may result in release of toxic fumes or render the heater ineffective
and cause smoke. Do not burn manufactured logs made of wax impregnated sawdust
or logs with any chemical additives. Manufactured logs made of 100% compressed
sawdust can be burned, but be careful burning too much of these logs at the same
time. Start with one manufactured log and see how the stove reacts. You can increase
the number of logs burned at a time to making sure the temperature never rises higher
than 475 °F (246 °C) on a magnetic thermometer for installation on single wall stove
pipes or 900 °F (482 °C) on a probe thermometer for installation on double wall stove
pipe. The thermometer should be placed about 18” (457 mm) above the stove. Higher
temperatures can lead to overheat and damage your stove.
-12-
TYPE
WEIGHT
(LBS. CU. FT.,
DRY)
PER CORD
EFFICIENCY
RANKING
SPLITS
MILLIONS
BTU’s/CORD
Hickory 63 4500 1.0 Well 31.5
White Oak 48 4100 .9 Fair 28.6
Red Oak 46 3900 .8 Fair 27.4
Beech 45 3800 .7 Hard 26.8
Sugar Maple 44 3700 .6 Fair 26.2
Black Oak 43 3700 .6 Fair 25.6
Ash 42 3600 .5 Well 25.0
Yellow Birch 40 3400 .4 Hard 23.8
Red Maple 38 3200 .3 Fair 22.6
Paper Birch 37 3100 .3 Easy 22.1
Elm/Sycamore 34 2900 .2 Very Difcult 20.1
Red Spruce 29 1800 .1 Easy 16.1
It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried for 9
to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very
important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily
dry, if it has been stored in poor conditions. Under extreme conditions it may rot instead of drying. This point
cannot be over stressed; the vast majority of the problems related to the operation of a wood stove is caused by
the fact that the wood used was too damp or had dried in poor conditions. These problems can be:
- ignition problems - creosote build-up causing chimney res
- low energy yield - blackened windows
- incomplete log combustion
Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be
stored directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between
each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be
protected from the elements but not the sides.
TESTING YOUR WOOD
When the stove is thoroughly warmed, place one piece of split wood (about ve inches in diameter) parallel to
the door on the bed of red embers. Keep the air control full open by pulling on it and close the door. If ignition
of the piece is accomplished within 90 seconds from the time if was placed in the stove, your wood is correctly
dried. If ignition takes longer, your wood is damp. If your wood hisses and water or vapor escapes at the ends
of the piece, your wood is soaked or freshly cut. Do not use this wood in your stove. Large amounts of creosote
could be deposited in your chimney, creating potential conditions for a chimney re.
TAMPER WARNING
This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal
regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating
instructions in this manual.
THE FIRST FIRES
The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited,
only burn small res in your stove for the rst four hours of operation. Never open the air control more than
necessary to achieve a medium burn rate.
Make sure that there’s enough air circulation while curing the stove. The odors could be smelled during the 3 or
4 rst res. Never start your stove outside. You will not be able to see if you are over heating.
Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing dead
wood can usually be considered to be about 2/3 seasoned. Splitting and stacking wood before it is stored
accelerates drying time. Storing wood on an elevated surface from the ground and under a cover or covered
area from rain or snow also accelerates drying time. A good indicator if wood is ready to burn is to check the
piece ends. If there are cracks radiating in all directions from the center then the wood should be dry enough
to burn. If your wood sizzles in the re, even though the surface is dry, it may not be fully cured, and should be
seasoned longer. Waste and other ammable materials should not be burned in your stove. Any type of wood
may be used in your stove, but specic varieties have better energy yields than others. Please consult the
following table in order to make the best possible choice.
-13-
IGNITION
After making sure that the stove air intake controls are fully open (completely pull-out towards you), The top
down method of re building is recommended for this appliance. After making sure that the stove air intake
controls are fully open (completely pull-out towards you), Place the largest pieces of wood on the bottom, laid in
parallel and close together. Smaller pieces are placed in a second layer, crossways to the rst. A third layer of still
smaller pieces is laid crossways to the second, this time with some spaces between. Then a fourth layer of loose,
small kindling and twisted newspaper sheets tops off the pile.
Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done
in order to avoid back draft problems often due to negative pressure in the house. If such is the case, open a
window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper
torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up
the chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper
and kindling wood inside the combustion chamber. When you have achieved a good bed of hot embers, we
recommend the following burn procedures:
CAUTION: Never alter the damper slide or the adjustment range to increase ring for any reason. Doing so could result in
heater damage and will void your warranty.
HEATING
Controlled combustion is the most efcient technique for wood heating because it enables you to select the type
of combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is
adjusted to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will
burn quickly if the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. Refer
to the primary air settings table for damper operation setting. Real operating conditions may give very different
results than those obtained during testing according to the species of wood used, its moisture content, the size
and density of the pieces, the length of the chimney, altitude and outside temperature.
EFFICIENCIES
Efciencies can be based on either the lower heating value (LHV) or the higher heating value (HHV) of the fuel.
The lower heating value is when water leaves the combustion process as a vapor, in the case of woodstoves the
moisture in the wood being burned leaves the stove as a vapor. The higher heating value is when water leaves
the combustion process completely condensed. In the case of woodstoves this would assume the exhaust gases
are room temperature when leaving the system, and therefore calculations using this heating value consider
the heat going up the chimney as lost energy. Therefore, efciency calculated using the lower heating value of
wood will be higher than efciency calculated using the higher heating value. In the United States all woodstove
efciencies should be calculated using the higher heating value.
The best way to achieve optimum efciencies is to learn the burn characteristic of you appliance and burn well-
seasoned wood. Higher burn rates are not always the best heating burn rates; after a good re is established a
lower burn rate may be a better option for efcient heating. A lower burn rate slows the ow of usable heat out
of the home through the chimney, and it also consumes less wood.
WARNINGS
• Never overre your stove. If any part of the stove starts to glow red, over ring is happening. Readjust the
air intake control at a lower setting.
• The installation of a log cradle or grates is not recommended in your wood stove. Build re directly on
rebrick.
• Never put wood above the rebrick lining of the rebox.
• Attempts to achieve heat output rates that exceed heater design specications can result in permanent
damage to the heater.
Primary Air Settings
(Slide Damper is located in center of stove under hearth plate)
(Damper Adjustment: Pulling out on damper increases air)
Electric Blower Speed Setting (Variable)
(Blower is on High when turned “ON”,
Rotate clockwise until stop for “LOW”.)
Burn Rate Adjust Damper from fully closed Burn Time Blower Speed
Low 1/4” (6.3mm) @ 30 minutes Low
Medium - Low 3/8” (9.5mm) @ 30 minutes Low
Medium - High 1/2” (12.7mm) @ 30 minutes Low
High approx. 3” (76mm) all minutes High
-14-
The amount of visible smoke being produced can be an effective method of determining how efciently the
combustion process is taking place at the given settings. Visible smoke consist of unburned fuel and moisture
leaving your stove. Learn to adjust the air settings of your specic unit to produce the smallest amount of visible
smoke. Wood that has not been seasoned properly and has a high wood moisture content will produce excess
visible smoke and burn poorly.
OPERATIONAL TIPS
• Get the appliance hot and establish a good coal bed before adjusting to a low burn rate (this may take 30
minutes or more depending on your wood)
• Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature
• Be considerate of the environment and only burn dry wood
• Burn small, intense res instead of large, slow burning res when possible
• Learn your appliance’s operating characteristics to obtain optimum performance
• Burning unseasoned wet wood only hurts your stoves efciency and leads to accelerated creosote buildup in
your chimney
RELOADING
Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air
controls to maximum a few seconds prior to opening the stove’s door. Then proceed by opening the door very
slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and
thus eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers
to the front of the stove and reload the unit. For optimal operation of your wood stove, we recommend you to
operate it with a wood load approximately equivalent to the height of re bricks. It is important to note that wood
combustion consumes ambient oxygen in the room .In the case of negative pressure, it is a good idea to allow
fresh air in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall.
Creosote - Formation and Need for Removal - When wood is burned slowly, it produces tar and other organic
vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively
cool chimney ue of a slow-burning re. As a result, creosote residue accumulates on the ue lining. When
ignited this creosote makes an extremely hot re. The chimney connector and chimney should be inspected
at least once every two months during the heating season to determine if a creosote build-up has occurred. If
creosote has accumulated (3mm or more), it should be removed to reduce the risk of a chimney re. We strongly
recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately 18” above the
stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke exhaust system.
The ideal temperature for these gases is somewhere between 275°F and 500°F. Below these temperatures, the
build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity is lost into the
atmosphere.
TO PREVENT CREOSOTE BUILD UP
• Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore less creosote
deposit.
• Leave the air control full open for about 5 min. every time you reload the stove to bring it back to proper
operating temperatures. The secondary combustion can only take place if the rebox is hot enough.
• Always check for creosote deposit once every two months and have your chimney cleaned at least once a
year.
If a chimney or creosote re occurs, close all dampers immediately. Wait for the re to go out and the heater to
cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to ensure there is
no more creosote deposits remaining in the chimney.
ASH DISPOSAL
Whenever ashes get 3 to 4 inches deep in your rebox or ash pan, and when the re has burned down and
cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the rebox bottom to help
maintain a hot charcoal bed. Ashes should be placed in a metal container with a tight-tting lid. The closed
container of ashes should be placed on a noncombustible oor or on the ground, away from all combustible
materials, pending nal disposal. The ashes should be retained in the closed container until all cinders have
thoroughly cooled.
CAUTIONS:
• Ashes could contain hot embers even after two days without operating the stove.
• The ash pan can become very hot. Wear gloves to prevent injury.
• Never burn the stove with the ash trap open. This would result in over ring the stove. Damage to the stove
and even house re may result.
-15-
SMOKE AND CO MONITORS
Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when
exposed to elevated concentrations for extended periods of time. While the modern combustion systems in
heaters drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or conned
areas can be dangerous. Make sure you stove gaskets and chimney joints are in good working order and sealing
properly to ensure unintended exposure. It is recommended that you use both smoke and CO monitors in areas
having the potential to generate CO.
MAINTENANCE
Your wood stove is a high efciency stove and therefore requires little maintenance. It is important to perform
a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged,
in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe
periodically for creosote buildup or obstructions.
GLASS
• Inspect and clean the glass regularly in order to detect any cracks. If you spot one, turn the stove off immediately.
Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is broken.
• If the glass on your stove breaks, replace only with the glass supplied from your heater dealer. Never substitute
other materials for the glass.
• To replace the glass, remove the screws retaining the glass mouldings inside the door. Remove the mouldings
and replace the damaged piece with a new one. Perform the procedure backwards after replacing. When
replacing the glass, you should change the glass gasket to make sure you keep it sealed.
• Never wash the glass with a product that may scratch. Use a specialized product, available in the stores where
wood stoves are sold. The glass should be washed only when cold.
GASKETING
It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in
order to insure good control over the combustion, maximum efciency and security. To change the door gasket,
simply remove the damaged one. Carefully clean the available gasket groove, apply a high temperature
silicone sold for this purpose, and install the new gasket. You may light up your stove again approximately 24
hours after having completed this operation. This unit’s door uses a 1/2” diameter rope gasket.
AIR TUBES
The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the
highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The
air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to
allow the tube to be removed and replaced.
PAINT
Remember to only clean your stove with a dry soft cloth that will not harm the stoves nish.
Your stove has two types of coatings that are used in the nal nish; porcelain enamel and high temperature
stove paint.
ENAMEL REPAIR
The porcelain enamel nish will maintain its color and luster for the life of the stove. However, because it is glass
it may chip if hit with a hard or sharp object. If you experience a scratch or chip in the porcelain enamel nish,
specially formulated gloss touch up paint can be used. Contact you stove dealer to request a small bottle of this
touch up paint.
1. Ensure the stove is cool.
Note: The paint may be applied to a warm stove, but the temperature of the section to be painted should be
below the boiling temperature (200°F) to achieve a smooth nish.
2. The area should be built up with multiple thin coats.
Note: Better results are obtained if the stove is brought up to operational temperatures between coats.
WARNING: Never operate the stove without a gasket or with a broken one. Damage to the stove or even
house re may result.
-16-
HIGH TEMPERATURE STOVE PAINT REPAIR
If the painted portions of your stove need re coating it is possible to give those pieces a brand new look by
repainting it with a 1200°F heat resistant stove paint.
1. Scrub the surface to be repainted with ne sand paper.
2. Clean it properly.
3. Apply thin coats (2-3) of paint successively.
AIR TUBES
The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the
highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The
air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to
allow the tube to be removed and replaced.
During the curing process there are changes in the paint causing it to give off an odor and some visible
smoke. The fumes are non-toxic, but can be unpleasant. Ventilate and vacate the room to avoid discomfort.
Once the curing is complete there will be no odor or smoke. After re-coating portions of your stove
remember to follow the curing process as discussed in the rst re section of this manual.
CAUTION: This wood heater needs periodic inspection and repair for proper operation. It is against federal
regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual.
ALTERNATE FLOOR PROTECTOR CALCULATIONS
Alternate materials may be rated with C-factor (Thermal Conductance) or k-factor (Thermal Conductivity)
ratings which must be converted to R-value to determine if the alternate material meets the tested requirements.
The following instructions provide the proper information and formulas for conversion to R-value.
To determine if alternate materials are acceptable follow this sequence.
Convert material specications to R-value:
a. R-value given — no conversion necessary
b. k-factor is given with a required thickness (T) in inches: R = 1/k x T
c. C-factor is given: R = 1/C
Determine the R-value of proposed alternate oor protector:
a. Use formulas in step 1 above to calculate R-value of proposed material(s).
b. For multiple layers, add R-values of each layer to determine overall R-value.
If the overall R-value of the oor protector system is equal to or greater than the oor protector specications
given, the alternate is acceptable.
Denitions:
Thermal conductance (C) = =
Thermal conductivity (k) = = =
Thermal resistance (R) = =
Example:
The specs of oor protector material should be 3/4-inch thick material with a k-factor of 0.84. The proposed
alternative material is 4” brick with a C-factor of 1.25 over 1/8-inch mineral board with a k-factor of 0.29.
Step 1: Convert specs to R-value.
R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = Rspecs
Step 2: Calculate R-value of individual components.
4” Brick with C-factor = 1.25. R = 1/C = 1/1.25 = 0.80 = Rbrick
1/8-inch (0.125”) mineral board with k-factor = 0.29. R = 1/0.29 x 0.125 = 0.431 = Rmin.brd.
Step 3: Add R-values of components to get total R-value of system.
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem
Step 4: Compare Rsystem to Rspecs.
Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required specications and therefore
is an acceptable alternative.
BTU
(hr)(ft²)(°F)
(Btu)(inch)
(hr)(ft²)(°F)
(hr)(ft²)(°F)
BTU
(m²)(°K)
W
W
(m²)(°K)
W
(m²)(°K)
BTU
(hr)(ft²)(°F)
-17-
REPAIR PARTS
1
2
3
4
5
6
9
7
8
16
15
14
13
12
11
10
17
Key Part No. Description Qty.
1 610061 Assy., Door Large Rect. 1
2 891331 Spring Handle - Brushed Nickel 1
3 26333 Cover Plate, Damper 1
4 88189 Gasket, Damper 1
5 69738 Weld., Damper Slide 1
6 40590 Hearth 1
7 891137 Handle, Brushed Nickel 1
8 69767 Ash Pan Weldment 1
9 40589 Front 1
10 40588 Side 2
11 40292A 6” Flue Collar 1
12 40587 Top 1
13 26934 Air Deector 1
14 891841 Assembly, AFS Blower 1
15 26335 Heat Shield 1
16 69768 Weldment, Ash Pan Housing 1
17 40566 Leg, Cast Iron 4
In order to maintain warranty, components must be replaced using original manufacturers parts purchased
through your dealer or directly from the appliance manufacturer.
Use of third party components will void the warranty.
-18-
REPAIR PARTS
Key Part No. Description Qty.
1 25465 Retainer, Bottom Glass 2
2 891813 Door Glass (40564) 1
3 88174 Gasket-Flat, Glass Retainer 4ft
4 88066 1/2 Rope Gasket 5ft
5 40639 Door,Rectangular - Large 1
6 892228 7” Handle 1
7 891135 Handle, Spring (Lg-Nickel) 1
2
3
4
5
6
7
1
Key Part No. Description Qty.
1
891414A
Half Firebrick 2
2 89066A Firebrick (4-1/2 x 9) 14
3 891783 Firebrick (3 x 4-1/2) 1
4 40561 Ash Plug 1
5 24103A Firebrick, Half (4-1/2 X 4-1/2) 1
6 86645 Tube (Ø7/32), Secondary Air 2
7 86643 Tube (Ø5/32) , Secondary Air 1
8 88146 Board, Ceramic Fiber 1
4
5
3 2
1
6
8
7
In order to maintain warranty, components must be replaced using original manufacturers parts purchased
through your dealer or directly from the appliance manufacturer.
Use of third party components will void the warranty.
-19-
The operation of this unit in a manner inconsistent with the owner’s manual
will void the warranty and is also against federal regulations. United States
Stove Company warrants this product to be free from defects in material and
workmanship, to the original retail purchaser only, for the time period identified
below, measured from the date of the initial purchase as evidenced on an
invoice, cancelled check, sales receipt, etc., to receipt of a claim by United
States Stove Company (“USSC”) or an authorized dealer, as follows:
WARRANTY CONDITIONS
• This warranty only covers USSC appliances that are purchased through an
USSC authorized retailer, dealer or distributor.
• This warranty is only valid while the USSC appliance remains at the site of
original installation. This warranty does not apply to products purchased for
rental use.
CLAIM PROCEDURE
Contact United States Stove Company for warranty service. You will be asked
to provide detailed descriptions and pertinent data, including proof or purchase
which will be returned upon request. Providing the heater has been installed
and used in accordance with the Owner’s Manual supplied with the heater
and the issue does not fall under a situation of exclusion, United States Stove
Company will either:
• Replace the defective part free of charge. Parts and/or service replacements
made under the terms of this warranty are warranted only for the remaining
period of the original heater warranty.
• Replace the heater free of charge. Should the heater be replaced by United
States Stove Company “free of charge”, all further warranty obligations are
thereby met.
• Where the defect is of a cosmetic (non-functional) nature, United States
Stove Company will bear reasonable expense to repair the heater, including
such items as welding, painting, and incidental labor. A “reasonable expense”
is defined by terms of this warranty as $30.00/hour with full refund for any
purchase of parts.
WARRANTY EXCLUSIONS
This warranty does not cover the following:
• Damage to or changes in surface finishes as a result of normal use. As a heating
appliance, some changes in color or interior and exterior surface finishes may
occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints,
accidents, misuse, scratches, melted items, or other external sources and
residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during
the warranty period. These parts include: paint, pellet, and the discoloration
of glass.
• Minor expansion, contraction, or movement of certain parts causing noise.
These conditions are normal and complaints related to this noise are not
covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance
in accordance with the installation instructions, operating instructions, and
listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes and/or authorities
having jurisdiction; (3) shipping or improper handling; (4) improper operation,
abuse, misuse, continued operation with damaged, corroded or failed
components, accident, alteration, or improperly/incorrectly performed repairs;
(5) environmental conditions, weather, inadequate ventilation, negative
pressure, or drafting caused by tightly sealed constructions, insufficient make-
up air supply, or handling devices such as exhaust fans or forced air furnaces
or other such causes; (6) use of fuels other than those specified in the operating
instructions; (7) installation or use of components not supplied with appliance
or any other components not expressly authorized and approved by USSC; (8)
modification of the appliance not expressly authorized and approved by USSC
in writing; and/or (9) interruptions or fluctuations of electrical power supply
to the appliance.
• Non-USSC venting components, hearth components or other accessories used
in conjunction with the appliance.
• USSC’s obligation under this warranty does not extend to the appliance’s
capability to heat the desired space. Information is provided to assist the
consumer and the dealer in selecting the proper appliance for the application.
Consideration must be given to appliance location and configuration,
environmental conditions, insulation and air tightness of the structure.
• Problems relating to smoking or creosote. Smoking is attributable to inadequate
draft due to the design or installation of the flue system or installation of the
heater itself. Creosote formation is largely attributable to improper operation of
the unit and/or draft as mentioned above.
• Any cost associated with product removal and re-installation, travel,
transportation, or shipping.
• Service calls to diagnose trouble (unless authorized in writing by the
manufacturer, distributor, or dealer).
THIS WARRANTY IS VOID IF
• The appliance has been over-fired or operated in atmospheres contaminated by
chlorine, fluorine, or other damaging chemicals. Over-firing can be identified
by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
• The appliance is subjected to prolonged periods of dampness or condensation.
• There is any damage to the appliance or other components due to water or
weather damage which is the result of, but not limited to, improper chimney or
venting installation.
LIMITATIONS OF LIABILITY
The owner’s exclusive remedy and USSC’s sole obligation under this warranty,
under any other warranty, express or implied, or in contract, tort or otherwise,
shall be limited to replacement, repair, or refund, in USSC’s sole and absolute
discretion. In no event will USSC be liable for any incidental or consequential
damages. THE LIMITED WARRANTY SET FORTH HEREIN IS THE
SOLE WARRANTY PROVIDED TO PURCHASER AND IS IN LIEU OF
ALL OTHER WARRANTIES AND REPRESENTATIONS, EXPRESS OR
IMPLIED. USSC MAKES NO REPRESENTATIONS OR WARRANTIES
WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE
PRODUCT, OTHER THAN (i) THE LIMITED WARRANTY ABOVE, AND
(ii) ANY IMPLIED WARRANTIES IMPOSED BY APPLICABLE LAW
WHICH CANNOT BE WAIVED OR DISCLAIMED UNDER APPLICABLE
LAW. ALL OTHER WARRANTIES OF ANY KIND, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED
AND EXCLUDED TO THE FULLEST EXTENT NOT PROHIBITED BY
APPLICABLE LAW. This Limited Warranty gives the purchaser specific
legal rights; a purchaser may have other rights depending upon where he or
she resides. Some states do not allow the exclusion or limitation of special,
incidental or consequential damages, or state law may affect the duration of
limitations, so the above exclusion and limitations may not be applicable.
WARRANTOR
The warrantor of record is United States Stove Company, PO Box 151, 227
Industrial Park Road, South Pittsburg, Tennessee 37380. Phone number: (800)-
750-2723. Register your product on line at www.usstove.com. Save your proof
of purchase, as documented in a receipt or invoice, with your records for any
claims.
IMPORTANT
We congratulate you on your selection of United States Stove Company and
its products. As the oldest solid fuel manufacturer in the United States (since
1869), the United States Stove Company is very proud of its products, service,
employees, and satisfied customers. We would like to hear from you if you are
not satisfied with the manner in which you have been handled by our distributor,
dealer, representative, customer service department, parts department, or sales
department. Please reach out to us by using any of the contact information
listed above.
Limited Warranty
852942B
TIME PERIOD
Firebox / Heat Exchanger Limited Lifetime
Door One Year
Cabinets and Trim One Year
Gaskets One Year
All Electrical Components (Blower, Auger
/ Agitator Motor, PC Board, Switches)
One Year
Ceramic Glass One Year
Service 01 Date:________________________
Engineer Name:_____________________________________
Company:__________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed.
Service Provider:
Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the
manufacturer’s instructions. Always use the manufacturer's specified spare part when replacement is necessary.
Service 02 Date:________________________
Engineer Name:_____________________________________
License No.:________________________________________ License No.:_______________________________________
Company:_________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
Service 03 Date:________________________
Engineer Name:_____________________________________
Company:__________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
Service 04 Date:________________________
Engineer Name:_____________________________________
Company:________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
Service 05 Date:________________________
Engineer Name:_____________________________________
Company:__________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
Service 06 Date:_______________________
Engineer Name:_____________________________________
Company:_________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
Service 07 Date:________________________
Engineer Name:_____________________________________
Company:__________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
Service 08 Date:_______________________
Engineer Name:_____________________________________
Company:_________________________________________
Telephone No.:______________________________________
Stove Inspected: Chimney Swept:
Items Replaced:____________________________________
License No.:_______________________________________ License No.:_______________________________________
License No.:_______________________________________ License No.:_______________________________________
License No.:_______________________________________ License No.:_______________________________________
Service Record
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
United States Stove AC2000 Le manuel du propriétaire
- Catégorie
- Poêle à bois
- Taper
- Le manuel du propriétaire