Simplicity 076461-01 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Installation and Operation Manual
35kW 48kW 60kW
Single Phase and Three Phase
Liquid Cooled Standby Generator System
This generator is rated in accordance with UL (Underwriters Laboratories) 2200 (stationary engine generator
assemblies) and CSA (Canadian Standards Association) standard C22.2 No. 100-4 (motors and generators).
Copyright © Briggs & Stratton Power Products Group, LLC
Milwaukee, WI, USA. All rights reserved.
80022440USCN
Revision A
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Milbank® generator. We are pleased that you’ve placed your confidence in the
Milbank brand. When operated and maintained according to the instructions in this manual, your generator will provide many
years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with standby generators and
how to avoid them.
Save these instructions for future reference.
This generator system requires professional installation before use. The installer should follow the installation instructions
completely.
Where to Find Us
You never have to look far to find support and service for your generator. Consult your Yellow Pages. There are many
authorized service dealers worldwide that provide quality service. You can also contact Technical Service by phone at
800-732-2989 between 8:00 AM and 5:00 PM central time or click on Dealer Locator at www.briggsandstratton.com, which
provides a list of authorized dealers.
For Future Reference
Please fill out the information below and keep with your receipt. Have this information at hand if it becomes necessary to
contact your installer or authorized dealer regarding service or repair of the unit.
DATE OF PURCHASE
GENERATOR
Model Number
Serial Number
Model Number
Model Revision
Serial Number
ENGINE
3
Table Of Contents
Important Safety Instructions .....................4
General Information..............................7
Installer Responsibilities ................................... 7
Owner Responsibilities .................................... 7
Battery Warmer Kit ....................................... 7
Installation Factors to Consider ............................. 8
Delivery Inspection ....................................... 8
Generator Location Considerations .......................... 8
Installation .....................................9
TO REDUCE THE RISK OF CARBON MONOXIDE POISONING 9
TO REDUCE THE RISK OF FIRE .......................... 11
Other Location Requirements.............................. 12
Electrical and Fuel Inlet Locations .......................... 12
Concrete Slab .......................................... 12
Lifting the Generator ..................................... 13
Planning the Gaseous Fuel Installation ............14
Fuel Pipe Sizing......................................... 14
Type of Fuel to Use ...................................... 15
Fuel Conversion......................................... 15
Fuel Pressure........................................... 15
Power Loss ............................................ 15
Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power Connections .............................17
Briggs & Stratton Controller Connections .................... 18
InteliNano Controller Connections .......................... 19
InteliLite Controller Connections ........................... 20
Battery ................................................ 21
Final Installation Considerations ........................... 21
Initial Start-up (No Load).................................. 22
Features and Controls...........................23
Access Panels .......................................... 23
Component Locations .................................... 24
Maintenance ...................................25
Cleaning the Generator................................... 25
Engine Air Cleaner....................................... 25
Electrical System Maintenance ............................ 26
Exhaust System Maintenance ............................. 26
Troubleshooting................................27
Generator Specifications ........................28
Wiring Diagrams................................29
1-Phase Briggs & Stratton ................................ 30
3-Phase InteliNano ...................................... 32
1-Phase InteliLite ........................................ 36
3-Phase InteliLite ........................................ 38
575-Volt InteliLite........................................ 42
4.3L Engine ............................................ 44
5.7L Engine ............................................ 46
4 BRIGGSandSTRATTON.COM
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation and maintenance of the generator and batteries.
Safety Symbols and Meanings
The safety alert symbol indicates a potential personal
injury hazard. A signal word (DANGER, WARNING, or
CAUTION) is used with the alert symbol to designate a
degree or level of hazard seriousness. A safety symbol
may be used to represent the type of hazard. The signal
word NOTICE is used to address practices not related to
personal injury.
DANGER
indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING
indicates a hazard which, if not avoided, could
result in death or serious injury.
CAUTION
indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE
indicates an action that could result in damage to
the product.
The manufacturer cannot anticipate every circumstance that
might involve a hazard. The warnings in this manual, and the
tags and decals affixed to the unit are, therefore, not all-
inclusive. If you use a procedure, work method or operating
technique that the manufacturer does not specifically
recommend, you must satisfy yourself that it is safe for you
and others. You must also make sure that the procedure,
work method or operating technique that you choose does
not render the generator system unsafe.
WARNING
The engine exhaust from this product
contains chemicals known to the State of California to
cause cancer, birth defects, or other reproductive harm.
WARNING
Certain components in this product and
related accessories contain chemicals known to the
State of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling.
WARNING
Running engine gives off carbon monoxide,
an odorless, colorless, poison gas.
Breathing carbon monoxide could result in death,
serious injury, headache, fatigue, dizziness,
vomiting, confusion, seizures, nausea or fainting.
Operate this product ONLY outdoors in an area that
will not accumulate deadly exhaust gas.
Keep exhaust gas away from any windows, doors,
ventilation intakes, soffit vents, crawl spaces, open
garage doors or other openings that can allow exhaust
gas to enter inside or be drawn into a potentially
occupied building or structure.
Carbon monoxide detector(s) MUST be installed and
maintained indoors according to the manufacturer’s
instructions/recommendations. Smoke alarms cannot
detect carbon monoxide gas.
WARNING
Storage batteries give off explosive
hydrogen gas during recharging.
Slightest spark will ignite hydrogen and cause
explosion, resulting in death or serious injury.
Battery electrolyte fluid contains acid and is
extremely caustic.
Contact with battery contents could cause severe
chemical burns.
A battery presents a risk of electrical shock and
high short circuit current.
DO NOT dispose of battery in a fire. Recycle battery.
DO NOT allow any open flame, spark, heat, or lit
cigarette during and for several minutes after charging a
battery.
DO NOT open or mutilate the battery.
Wear protective goggles, rubber apron, rubber boots and
rubber gloves.
Remove watches, rings, or other metal objects.
Use tools having insulated handles.
Explosion
Fire
Electrical Shock
Rotating Parts
Hot Surface
Toxic Fumes
Chemical BurnExplosive PressureAuto Start
Lift Hazard
Read Manual
5
WARNING
Generator produces hazardous voltage.
Failure to properly ground generator could result
in electrocution.
Failure to isolate generator from utility power could result
in death or serious injury to electric utility workers due to
backfeed of electrical energy.
DO NOT touch bare wires or bare receptacles.
DO NOT use generator with electrical cords which are
worn, frayed, bare or otherwise damaged.
DO NOT handle generator or electrical cords while
standing in water, while barefoot, or while hands or
feet are wet.
If you must work around a unit while it is operating,
stand on an insulated dry surface to reduce the risk of
a shock hazard.
DO NOT allow unqualified persons or children to
operate or service generator.
In case of an accident caused by electrical shock,
immediately shut down the source of electrical
power and contact the local authorities. Avoid direct
contact with the victim.
Despite the safe design of the generator, operating
this equipment imprudently, neglecting its
maintenance or being careless could cause possible
injury or death.
Remain alert at all times while working on this
equipment. Never work on the equipment when you
are physically or mentally fatigued.
Before performing any maintenance on the generator,
disconnect the battery cable indicated by a
NEGATIVE, NEG or (-) first. When finished, reconnect
that cable last.
After your system is installed, the generator may
crank and start without warning any time there is a
power failure. To prevent possible injury, always set the
generator’s system switch to OFF, remove the service
disconnect from the disconnect box AND remove the
15 Amp fuse BEFORE working on the equipment.
WARNING
Propane and Natural Gas are extremely
flammable and explosive, which could cause
burns, fire or explosion resulting in death or
serious injury.
Install the fuel supply system according to NFPA 37
and other applicable fuel-gas codes.
Before placing the generator into service, the fuel
system lines must be properly purged and leak tested.
After the generator is installed, you should inspect the
fuel system periodically.
NO leakage is permitted.
DO NOT operate engine if smell of fuel is present or
other explosive conditions exist.
DO NOT smoke around the generator. Wipe up any
oil spills immediately. Ensure that no combustible
materials are left in the generator compartment. Keep
the area near the generator clean and free of debris.
WARNING
Exhaust heat/gases could ignite
combustibles or structures resulting in death
or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
DO NOT touch hot parts and AVOID hot exhaust
gases.
Allow equipment to cool before touching.
Exhaust outlet side of weatherproof enclosure must
have at least 5 ft. (1.5m) minimum clearance from any
structure, shrubs, trees or any kind of vegetation.
Standby generator weatherproof enclosure must be
at least 5 ft. (1.5m) from windows, doors, any wall
opening, shrubs or vegetation over 12 inches (30.5
cm) in height.
Standby generator weatherproof enclosure must have
a minimum of 5 ft. (1.5 m) overhead clearance from
any structure, overhang, or trees.
DO NOT place weatherproof enclosure under a deck
or other type of structure that may confine airflow.
Use only flexible fuel line provided. Connect provided
fuel line to generator. DO NOT use with or substitute
any other flexible fuel line.
Smoke detector(s) MUST be installed and maintained
indoors according to the manufacturer’s instructions/
recommendations. Carbon monoxide alarms cannot
detect smoke.
Keep at least minimum distances shown in General
Location Guidelines to insure for proper generator
cooling and maintenance clearances.
Replacement parts must be the same and installed in
the same position as the original parts.
WARNING
Hazardous Voltage - Contact with power lines
could cause electric shock or burns, resulting in
death or serious injury.Lifting Hazard / Heavy Object
- Could result in serious injury.
If lifting or hoisting equipment is used, DO NOT
contact any power lines.
DO NOT lift or move generator without assistance.
DO NOT lift unit by roof as damage to generator
will occur.
6 BRIGGSandSTRATTON.COM
CAUTION
Installing the 15A fuse could cause the
engine to start at any time without warning resulting
in minor or moderate injury.
Observe that the 15 Amp fuse has been removed from
the control panel for shipping.
DO NOT install this fuse until all plumbing and wiring
has been completed and inspected.
WARNING
Moving parts could crush and cut.
Starter and other rotating parts could
entangle hands, hair, clothing, or
accessories resulting in serious injury.
NEVER operate generator without protective
housings, covers, or guards in place.
DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
Tie up long hair and remove jewelry.
Before servicing, remove 15 Amp fuse from control
panel and disconnect Negative (NEG or -) battery
cable.
WARNING
Hot pressurized coolant could cause serious
injury.
DO NOT open radiator cap when hot.
Before servicing, allow coolant to cool.
CAUTION
Excessively high operating speeds could
result in minor injury and/or equipment damage.
Excessively low speeds impose a heavy load on generator.
DO NOT tamper with governed speed. Generator
supplies correct rated frequency and voltage when
running at governed speed.
DO NOT modify generator in any way.
NOTICE
Improper treatment of generator could damage it
and shorten its life.
Use generator only for intended uses.
If you have questions about intended use, contact your
authorized dealer.
Operate generator only on level surfaces.
Adequate, unobstructed flow of cooling and ventilating
air is critical to correct generator operation.
The access panels/doors must be installed whenever
the unit is running.
DO NOT expose generator to excessive moisture,
dust, dirt, or corrosive vapors.
Remain alert at all times while working on this
equipment. Never work on the equipment when you
are physically or mentally fatigued.
DO NOT start engine with air cleaner or air cleaner
cover removed.
DO NOT insert any objects through cooling slots.
DO NOT use the generator or any of its parts as a
step. Stepping on the unit could cause stress and
break parts. This may result in dangerous operating
conditions from leaking exhaust gases, fuel leakage,
oil leakage, etc.
If connected devices overheat, turn them off and
disconnect them from generator.
Shut off generator if:
-electrical output is lost;
-equipment sparks, smokes, or emits flames;
-unit vibrates excessively or makes unusual noises.
NOTICE
Exceeding the generator wattage/amperage
capacity could damage the generator and/or electrical
devices connected to it. Start generator and let engine
stabilize before connecting electrical loads.
7
General Information
For most applications, the Installation and Operation Manual
contains all the information required to properly install,
operate, and maintain the generator.
Every effort has been made to ensure that information in this
manual is accurate and current. However, we reserve the
right to change, alter, or otherwise improve the product and
this document at any time without prior notice.
Ensure that this manual is given to the owner after the
installation has been completed.
Equipment Description
This product is intended only for use as an optional
generator system to provide an alternate source of electric
power and to serve loads such as heating, refrigeration
systems, and communication systems that, when stopped
during any power outage, could cause discomfort or
inconvenience.
NOTICE Only models equipped with the MRS19 controller
qualify for either an emergency standby or legally required
standby system as defined by NFPA 70 (NEC). For complete
information on these types of installations, consult NFPA 70
and NFPA 110.
Emergency generator systems are intended to
automatically supply illumination, power, or both, to
designated areas and equipment in the event of failure
of the normal supply. Emergency systems may also
provide power for such functions as ventilation where
essential to maintain life, where current interruption of
the normal supply would produce serious life safety or
health hazards.
Legally required standby generator systems are
intended to automatically supply power to selected
loads in the event of failure of the normal source which
could create hazards or hamper rescue or fire-fighting
operations.
Before Installation
Only current licensed electrical and plumbing professionals
should attempt generator system installations. Installations
must strictly comply with all applicable codes, industry
standards, laws, and regulations.
In some areas you may need electrical permits for installing
the generator, building permits for intalling gas lines, and
permits for noise allowances. The installer should check local
codes and obtain the necessary permits before installing the
system.
The generator warranty is VOID unless the system is
installed by licensed electrical and plumbing professionals.
Installer Responsibilities
Read and observe the safety instructions.
Install only a UL-approved transfer switch that is
compatible with the generator.
Read and follow the instructions in this installation and
operation manual.
Installation must strictly comply with all applicable
codes, industry standards, laws, and regulations.
Allow sufficient room on all sides of the generator for
maintenance and servicing.
Owner Responsibilities
Read and follow the instructions in this installation and
operation manual.
Follow a regular schedule for maintaining and using
the generator, as specified in this manual.
Carbon monoxide detector(s) MUST be installed and
maintained indoors according to the manufacturer’s
instructions and recommendations. Smoke alarms
cannot detect carbon monoxide gas.
Smoke detector(s) MUST be installed and maintained
indoors according to the manufacturer’s instructions
and recommendations. Carbon monoxide alarms
cannot detect smoke.
Battery Warmer Kit
If operating the generator below 30°F (-1°C), it is
recommended to install the optional Battery Warmer Kit.
The battery warmer is available separately through servicing
dealers under part number 6343.
8 BRIGGSandSTRATTON.COM
Installation Factors to Consider
The illustrations shown in this manual are for typical
circumstances. They are meant to familiarize you with the
installation options available for the generator.
Federal and local codes, appearance, noise levels, fuel
types, and distances are installation factors that must be
considered. Remember that, as the distance increases
from the existing electrical service and gaseous fuel supply,
and the number of bends in the fuel supply increases,
compensations must be made for piping and wiring
materials. This is necessary to comply with local codes
and overcome electrical voltage drops and gaseous fuel
pressure drops.
The factors mentioned above will have a direct effect on the
overall price of the generator installation.
Delivery Inspection
Avoid damage from dropping, bumping, or collision with the
shipping carton. Store and unpack the unit with the proper
side up, as noted on the shipping carton.
After removing the carton, carefully inspect the generator for
any damage that may have occurred during shipment.
If loss or damage is found at time of delivery, have the
person(s) making delivery note the loss or damage on the
freight bill and affix his signature under the consignor’s
memo of loss or damage. If the loss or damage is noted after
delivery, separate the damaged materials and contact the
carrier for claim procedures. Missing or damaged parts are
not warranted.
The standby generator system is supplied with:
Fully-serviced coolant system
Fully-serviced oil/lubricating system
Flexible fuel hook-up hose
Installation and Operation Manual
Spare access door keys
Spare 15 Amp ATO-type fuse
Touch up paint
Not Supplied:
Carbon monoxide detector(s)
Smoke detector(s)
Starting battery
Reinforced concrete pad
Connecting wire and conduit
Fuel supply valves/plumbing
60” lengths of 2” Schedule 40 pipe (NOT conduit)
Crane, lifting straps, chains or cables, spreader bar
Torque screwdriver, 5 to 50 inch-pound range
Voltage/frequency meter
Various special tools or equipment
Generator Location Considerations
The installation location of the generator has a direct effect
on:
1. The amount of plumbing required to fuel the generator.
2. The amount of wiring required to control and connect
the generator.
3. The safety of the installation regarding exhaust gas and
carbon monoxide hazards, fire risks, proximity to other
utilities, and exposure to weather elements.
Specific location guidelines are discussed in the next
section. The owner and installer should consult one another
to determine how the site might affect installation costs and
compliance with local codes and standards.
9
C
B
B
Installation
Before deciding on the final placement of the generator, the owner and installer must discuss and understand several
location guidelines. There are two critical safety concerns to be addressed - carbon monoxide poisoning and the risk of fire,
as follows:
WARNING Running engine gives off carbon monoxide, an
odorless, colorless, poison gas.
Breathing carbon monoxide could result in death, serious
injury, headache, fatigue, dizziness, vomiting, confusion,
seizures, nausea or fainting.
Operate this product ONLY outdoors in an area that will not
accumulate deadly exhaust gas.
Keep exhaust gas away from any windows, doors, ventilation
intakes, soffit vents, crawl spaces, open garage doors or other
openings that can allow exhaust gas to enter inside or be
drawn into a potentially occupied building or structure.
Carbon monoxide detector(s) MUST be installed and
maintained indoors according to the manufacturer’s instructions
and recommendations. Smoke alarms cannot detect carbon
monoxide gas.
WARNING
Exhaust heat or gases could ignite
combustibles or structures resulting in death or
serious injury.
Exhaust outlet end of standby enclosure must be at
least 5 ft (1.5 m) from any structure, shrubs, trees or
any kind of vegetation.
Standby enclosure must be at least 5 ft (1.5 m) from
windows, doors, any wall opening, shrubs, or
vegetation over 12 inches (30.5 cm) in height.
Standby enclosure must have at least 5 feet (1.5 m)
overhead clearance from any structure, overhang, or trees.
DO NOT place standby enclosure under a deck or
other type of structure that may confine airflow.
USE ONLY the flexible steel fuel line provided.
Connect provided fuel line to generator. DO NOT use
with or substitute any other flexible fuel line.
Smoke detectors MUST be installed and maintained
indoors according to the manufacturer’s instructions
and recommendations. Carbon monoxide alarms
cannot detect smoke.
TO REDUCE THE RISK OF CARBON MONOXIDE POISONING
Follow the installation requirements listed below. The figure below illustrates potential points of entry for carbon monoxide
gas.
Ensure that generator exhaust gas is kept away from:
Overhead doors (B, shown above)
Entrance doors (C, shown above)
Windows (not shown)
Other openings that could allow exhaust gas to enter
inside or be drawn into a potentially occupied building
or structure.
10 BRIGGSandSTRATTON.COM
All fossil fuel burning products, such as standby
generators, emit carbon monoxide (CO) gas in the
engine exhaust. CO gas is odorless, colorless and
tasteless and is unlikely to be noticed until a person is
overcome. CO gas can kill you. It is required that the
following be included as part of the installation:
Install the generator outdoors in an area that
will not accumulate deadly exhaust gas.
DO NOT install the generator where exhaust
gas could accumulate and enter inside or be
drawn into a potentially occupied building or
structure.
Nearby structures may be exposed to the engine
exhaust from the unit and must be considered
when installing the standby generator.
Wind and air currents should be taken into
consideration when positioning the generator.
Place the generator in an area where winds will
carry the exhaust gas away from any potentially
occupied building or structure.
DO NOT place the standby generator in any area
where leaves or debris normally accumulate.
By law, many states require a fully operating
Carbon Monoxide (CO) detector in homes
and other structures occupied by people.
Carbon monoxide detectors (shown below)
MUST be installed and maintained indoors
according to the manufacturer’s instructions and
recommendations. A carbon monoxide detector
is an electronic device that detects hazardous
levels of CO. When there is a buildup of CO,
the monitor will alert the occupants by flashing
a visual indicator light and sounding an alarm.
Smoke alarms cannot detect CO gas.
Direct the standby generator exhaust (A, shown
below) away from or parallel to the building or
structure. DO NOT direct the generator exhaust
towards a potentially occupied building, structure,
windows, doors, ventilation intakes, soffit vents,
crawl spaces, open garage doors, or other openings
where exhaust gas could accumulate and enter
inside or be drawn into a potentially occupied
building or structure.
The engine exhaust exits the top of the housing (A).
A
11
TO REDUCE THE RISK OF FIRE
Follow the installation requirements listed below. The figures below illustrate the minimum distances from structures and
vegetation to reduce the risk of fire.
The National Fire Protection Association (NFPA) standard NFPA 37 establishes criteria for minimizing the hazard of
fire during the installation and operation of stationary combustion engines. NFPA 37 limits the spacing of an enclosed
generator from openings in walls, structures and combustible materials outside the enclosure. The following generator
placement requirements are based on compliance to NFPA 37 2010 section 4.1.4.
5 ft (1.5 m) min.
Standby
5 ft (1.5 m) min.
Exhaust
B
A
5 ft (1.5 m) min.
Standby
5 ft (1.5 m) min.
Exhaust
A
A
B
5 ft (1.5 m) min.
Standby
5 ft (1.5 m) min.
Exhaust
B
A
A
A Standby enclosure must be at least 5 ft (1.5 m)
from windows, doors, any wall opening, shrubs,
or vegetation over 12 inches (30.5 cm) in height.
B Exhaust outlet end of standby enclosure must
be at least 5 ft (1.5 m) from any structure,
shrubs, trees, or any kind of vegetation.
C Standby enclosure must have at least 5 feet (1.5 m)
overhead clearance from any structure, overhang, or
trees.
DO NOT place standby enclosure under a deck or other
type of covered structure that may confine airflow.
5 ft (1.5 m) min.
5 ft (1.5 m) min.
Standby
5 ft (1.5 m) min.
Exhaust
B
A
A
A
A
B
C
12 BRIGGSandSTRATTON.COM
Other Location Requirements
Place the standby generator in a prepared location
that is flat and has provisions for water drainage.
Install the standby generator in a location where
sump pump discharge, rain gutter down spouts, roof
run-off, landscape irrigation, or water sprinklers will
not flood the unit or spray the enclosure, or enter any
air inlet or outlet openings.
Install the standby generator where it will not affect
or obstruct any utility services (including covered,
concealed, and underground), such as telephone,
electric, fuel (natural gas / LPG vapor), irrigation, air
conditioning, cable, septic, sewer, well, etc.
Install the standby generator where leaves, grass,
snow, etc will not obstruct air inlet and outlet
openings. If prevailing winds will cause blowing or
drifting, a windbreak may be needed to protect the
unit.
Electrical and Fuel Inlet Locations
A through-slab power cable stub-up is recommended.
If a stub-up is not used, (B, below) indicates the
recommended location for punching a hole to attach
power conduit. The 1” (25.4 mm) NPT fuel inlet connector
(A) is shown for reference.
Concrete Slab
The generator must be installed on a reinforced concrete
slab, constructed as follows:
28 day compression strength of 3000 psi (200 MPa)
Minimum 5” (13 cm) thick
Minimum 6” (15 cm) wider than the standby enclosure
on all sides
Strengthen slab with No. 6 reinforcing bars on 12” (30.5
cm) centers or 8 ga. steel wire fabric with 6” (15 cm)
centers
Avoid placing reinforcement in the entrance stub-up
area
The following dimensions will be needed to properly size and
configure the slab. Refer to figure at right:
A - Enclosure dimensions
35kW = 88” (224 cm) long x 37” (94 cm) wide
48kW = 88” (224 cm) long x 37” (94 cm) wide
60kW = 96” (244 cm) long x 37” (94 cm) wide
B - Generator mounting holes
35kW = 85” (216 cm) long x 34.25” (87 cm) wide
48kW = 85” (216 cm) long x 34.25” (87 cm) wide
60kW = 94” (239 cm) long x 34.25” (87 cm) wide
C - Fuel inlet location
35kW = 45.5” (116 cm)
48kW = 45.5” (116 cm)
60kW = 52” (132 cm)
D - Entrance stub-up area
35kW = 10.5” (27 cm) long x 6.75” (17 cm) wide
48kW = 10.5” (27 cm) long x 6.75” (17 cm) wide
60kW = 6.0” (15 cm) long x 5.25” (13 cm) wide
D1 x D2 - Entrance stub-up location
35kW = 8.5” (22 cm) x 7.75” (20 cm)
48kW = 8.5” (22 cm) x 7.75” (20 cm)
60kW = 16.0” (41 cm) x 7.0” (18 cm)
A
B
13
A - Standby generator enclosure
B - Mounting holes in generator base
C - Fuel inlet location
D - Entrance stub-up area
D1 x D2 - Entrance stub-up location
E - Exhaust outlet area reference
F - Concrete slab reference
WARNING
Hazardous Voltage - Contact with power lines
could cause electric shock or burns, resulting
in death or serious injury.
Lifting Hazard / Heavy Object - Could result
in serious injury.
If lifting or hoisting equipment is used, DO NOT
contact any power lines.
DO NOT lift or move generator without assistance.
Use lifting pipes as described below.
DO NOT lift unit by roof as damage to generator
will occur.
Lifting the Generator
Proper tools, equipment, and qualified personnel should be
used in all phases of handling and moving the generator.
The approximate weight of the generator is listed in the
Generator Specifications Section.
Two 60” (1.5 m) lengths of 2” Schedule 40 pipe (C, below),
supplied by the installer, are required to lift the generator
onto the concrete pad. Insert the pipes through the lifting
holes (D) located in the base of the generator. (Hooks may
be used in the lifting holes in place of the pipe in accordance
with OSHA or local lifting regulations.) Use a spreader bar
to ensure that the chains, straps, or cables do not touch the
generator roof. Retouch any chipped paint with supplied
touch-up paint.
Attach the generator to the slab at the four corner locations
(B) with minimum 5/16” diameter (8mm) masonry anchor
bolts (or as required by local code) long enough to secure
the unit.
C
D
B
D
C
F
E
A
B
D2
D
D1
D
C
B
14 BRIGGSandSTRATTON.COM
Planning the Gaseous Fuel
Installation
The information provided below is intended to assist
gaseous fuel system technicians in planning installations.
State and local codes may override some of these
recommendations. Consult with the local fuel supplier or fire
marshall if clarification is needed.
WARNING
Propane
and Natural Gas are extremely
flammable and explosive, which could cause
burns, fire or explosion resulting in death or
serious injury.
LP gas is heavier than air and will settle in low areas.
Natural gas is lighter than air and will collect in
high areas.
The slightest spark could ignite these fuels and cause
an explosion.
DO NOT light a cigarette or smoke.
A minimum of one accessible, approved manual
shutoff valve (F) shall be installed in the fuel supply
line within 6 ft (180 cm) of the generator.
A manual fuel shut-off valve located in the interior of
the building.
Where local conditions include earthquake,
tornado, unstable ground, or flood hazards, special
consideration shall be given to increase strength and
flexibility of piping supports and connections.
Piping must be of the correct size to maintain the
required supply pressures and volume flow under
varying generator load conditions with all gas
appliances connected to the fuel system turned on
and operating.
Use a pipe sealant or joint compound approved for
use with NG/LPG on all threaded fittings to reduce the
possibility of leakage.
Installed piping must be properly purged and
leak tested, in accordance with applicable codes
and standards.
The owner and installer should consult one another to review
any changes to the installation plan that might arise when
applying the following guidelines for gaseous fuel plumbing.
The piping material must conform to federal and local
codes, be rigidly mounted, and be protected against
vibration.
Piping should be protected from physical damage
where it passes through flower beds, shrub beds, and
other cultivated areas where damage could occur.
Install the supplied flexible gaseous hose (B, at right)
between the generator fuel inlet port (A) and the rigid
piping to prevent thermal expansion and contraction
from causing excessive stress on the piping material.
NOTICE
The supplied flexible gaseous pipe is not to be
installed underground or in contact with the ground. The
entire flexible gaseous pipe must be visible for periodic
inspection and must not be concealed within nor contact nor
run through any wall, floor, or partition.
A union (C) or flanged connection shall be provided
downstream to permit removal of controls.
A manometer test port (D) should be installed. The
port permits temporary installation of a manometer
to check whether the engine is receiving the correct
fuel pressure to operate efficiently throughout its
operating range. A digital manometer (P/N 19495) is
available at your service center. When the initial test
runs are completed, the manometer is removed and the
port is plugged.
Where the formation of hydrates or ice is known to
occur, piping should be protected against freezing.
The termination of hard piping should include a
sediment trap (E) where condensate is not likely to
freeze.
A
B
C
D
E
F
A - Generator Fuel Inlet
B - Flexible Fuel Hose
C - Union Fitting
D - Manometer Test Port
E - Sediment Trap
F - Manual Shut-off Valve
Fuel Pipe Sizing
There are numerous on-line or printed references for fuel
pipe sizing. For example, NFPA 54 - National Fuel Gas
Code, 2006 (Item #320-6031-06) is a common resource.
The installer should consider the specific gravity of gas,
compensate for a nominal amount of restriction from
bends and fittings, and refer to federal and local codes for
guidance.
15
Fuel Conversion
The engine was set at the factory to run on natural gas (NG).
To convert the engine to run on liquid propane (LP Vapor), or
to change back to NG later, follow these steps:
1. Open the controller door.
2. Locate fuel selector switch on side of circuit breaker
enclosure.
3. Move the switch (A, below) to LP or NG.
4. Close the controller door.
Type of Fuel to Use
An important consideration affecting the entire
installation is the type of fuel to be supplied. The system
was tested and adjusted at the factory using either
natural gas or liquid propane (LP vapor). For proper
engine function, follow these guidelines:
Use clean, dry fuel, free of moisture or any
particulate material.
For engines running on propane (LP), use
commercial grade HD5 propane with a minimum
fuel energy of 2500 BTU/ft³ with maximum
propylene content of 5% and butane and heavier
gas content of 2.5% and minimum propane
content of 90%.
For engines running on natural gas, power output
ratings will depend on the specific fuel but typical
derates are between 10 to 20% off the LP rating.
Using fuels outside the recommended values may
cause performance problems.
WARNING
Propane and Natural Gas are extremely
flammable and explosive, which could cause burns, fire or
explosion resulting in death or serious injury.
The generator is equipped with an automatic safety
gas “fuel shut-off valve.
DO NOT operate the equipment if the “fuel shut-off
valve is missing or inoperative.
A
Fuel Pressure
Both LP vapor and natural gas fuel supply pressure at
the generator fuel inlet port should be 7 - 11 inch WC
(17 - 28 mBar) at full load and with all gas appliances
turned on and operating. Maximum pressure drop from
static (engine not running) to full load is 0.5 inch WC
(1.3 mbar). Maximum pressure with engine OFF at no
load is 13.85 inch WC (34.5 mbar).
Power Loss
Air density is less at high altitudes, resulting in less
available engine power. Specifically, engine power will
decrease 3% for each 1,000 feet (300 m) above sea
level and 1% for each 10°F (5.6°C) above 77°F (25°C).
Generators using power management technology must
have the transfer switch programmed appropriately for
this power decrease.
Physical Properties LP Vapor Natural
Gas
Normal Atmospheric State Gas Gas
Boiling Point (in °F):
Initial
End
-44
-44
-259
-259
Heating Value:
BTU per gallon (Net LHV *)
BTU per gallon (gross **)
BTU per cubic feet (gas)
83,340
91,547
2,500
63,310
1,000
Density *** 36.39 57.75
Weight † 4.24 2.65
Research Octane Number
Motor Octane Number
110+
97
110+
* LHV (Low Heat Value) is the more realistic rating.
** Gross heat value does not consider heat lost in the
form of water during combustion.
*** Density is given in “Cubic Feet of Gas per Gallon of
Liquid”.
Weight is given in “Pounds per Gallon of Liquid”.
16 BRIGGSandSTRATTON.COM
Fuel Consumption
Shown below are the estimated fuel supply
requirements at full load, 1/2-load, and exercise load for
LP Vapor and NG fuels.
Series 35000 LP Vapor Fuel Consumption
Full Load 1/2 Load Exercise
BTU/hr 399116 257844 136087
ft³/hr 160 103 54
m³/hr 4.5 2.9 1.5
Gal/hr 4.4 2.8 1.5
Series 35000 NG Fuel Consumption
Full Load 1/2 Load Exercise
BTU/hr 393844 253217 144718
ft³/hr 394 253 145
m³/hr 11.2 7.2 4.1
Series 48000 LP Vapor Fuel Consumption
Full Load 1/2 Load Exercise
BTU/hr 505670 312177 135654
ft³/hr 202 125 54
m³/hr 5.7 3.5 1.5
Gal/hr 5.5 3.4 1.5
Series 48000 NG Fuel Consumption
Full Load 1/2 Load Exercise
BTU/hr 470963 298120 151601
ft³/hr 471 298 152
m³/hr 13.3 8.4 4.3
Series 60000 LP Vapor Fuel Consumption
Full Load 1/2 Load Exercise
BTU/hr 800300 581550 247050
ft³/hr 320 233 99
m³/hr 9.1 6.6 2.8
Gal/hr 8.7 6.4 2.7
Series 60000 NG Fuel Consumption
Full Load 1/2 Load Exercise
BTU/hr 681500 512040 240840
ft³/hr 682 512 241
m³/hr 19.3 14.5 6.8
17
Power Connections
Compare this illustration with the generator to familiarize yourself with the location of these connections.
B
C
A
A - Power Connection - Power connection to transfer
switch.
B - Neutral Connection - Connect to transfer switch neutral.
C - Ground Connection - Connect to transfer switch
ground.
Ground the generator per applicable codes, standards, and
regulations. There are two generator GND lug locations.
The location shown by (C, above) should suffice for most
applications. The second generator GND lug is located
on the frame below the generator circuit breaker cover.
This should ONLY be used for a ground rod located at the
generator, if required by local codes.
For system connections such as remote start, e-stops,
and controller inputs and outputs, refer to the connection
diagrams on the following pages.
For power output connection, use 300 volt, 167
-194°F (75-90°C) wire. See chart for proper wire size.
For utility circuit connection, use #14 AWG minimum
300 volt, 167-194°F (75-90°C) wire.
For transfer switch communication, use #18 AWG
twisted pair conductors, no greater than 200 ft (60 m)
in length, 300 volt, 167-194°F (75-90°C) wire.
Series 35000 Voltage Rated Amps Wire Size
1-Phase 120/240 145 2/0
3-Phase Wye 120/208 121 1/0
3-Phase Delta 120/240 105 1 AWG
3-Phase Wye 240/416 61 4 AWG
3-Phase Wye 277/480 53 6 AWG
3-Phase Wye 347/600 42 8 AWG
Series 48000 Voltage Rated Amps Wire Size
1-Phase 120/240 200 4/0
3-Phase Wye 120/208 167 3/0
3-Phase Delta 120/240 144 2/0
3-Phase Wye 240/416 83 3 AWG
3-Phase Wye 277/480 72 4 AWG
3-Phase Wye 347/600 58 4 AWG
Series 60000 Voltage Rated Amps Wire Size
1-Phase 120/240 250 300 kcmil
3-Phase Wye 120/208 215 250 kcmil
3-Phase Delta 120/240 186 4/0
3-Phase Wye 240/416 108 1 AWG
3-Phase Wye 277/480 93 2 AWG
3-Phase Wye 347/600 75 4 AWG
Refer to the Data Tag to determine the series of generator.
A
18 BRIGGSandSTRATTON.COM
19
20 BRIGGSandSTRATTON.COM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108

Simplicity 076461-01 Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur