RedMax Edger HEZ2602S Manuel utilisateur

OWNER/OPERATOR MANUAL

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

STICK EDGERS

COUPE-BORDURES

CORTACÉSPEDES

848-A47-93A1 (701)

HEZ2401S

HEZ2602S

HEZ3001S

APPLICABLE SERIAL NUMBERS :

DRIVE UNIT 70200101 and up

ENGINE UNIT 70200101 and up

NUMEROS DE SERIE APPLICABLES :

BOITE DE COMMANDES 70200101 et au-delà

MOTEUR 70200101 et au-delà

NÚMEROS DE SERIE APLICABLES:

UNIDAD DE ACCIONAMIENTO 70200101 y superior

UNIDAD DE MOTOR 70200101 y superior

WARNING

The engine exhaust from

this product contains

chemicals known to the

State of California to cause

cancer, birth defects or

other reproductive harm.

WARNING

ADVERTENCIA

AVERTISSEMENT

ADVERTENCIA

Before using our products,

please read this manual

carefully to understand the

proper use of your unit.

Los gases de escape del

motor de este producto

contienen sustancias

químicas conocidas por el

Estado de California como

causantes de cáncer,

malformaciones en recién

nacidos y otros problemas

de reproducción.

Les échappements du

moteur de ce produit

contiennent des produits

chimiques connus par l’Etat

de Californie comme étant

responsables de cancers,

d’anomalies congénitales et

d’autres atteintes à

l’appareil reproducteur.

Antes de usar nuestros

productos, lea

detenidamente este manual

a fin de familiarizarse con el

uso correcto de este

aparato.

Avant d’utiliser cette

ce

produit

, veuillez lire

attentivement ce manuel

afin de bien comprendre le

bon fonctionnement de cet

appareil.

2

SAFETY FIRST

Instructions contained in warnings within this

manual marked with a symbol concern critical

points which must be taken into consideration to

prevent possible serious bodily injury, and for this

reason you are requested to read all such

instructions carefully and follow them without fail.

■ WARNINGS IN THE MANUAL

This mark indicates instructions which must be

followed in order to prevent accidents which could lead

to serious bodily injury or death.

This mark indicates instructions which must be

followed, or it leads to mechanical failure, breakdown,

or damage.

This mark indicates hints or directions useful in the use

of the product.

NOTE

IMPORTANT

WARNING

1. Parts location………………………………………4

2. Specifications………………………………………4

3. Warning labels on the machine ………………10

4. Symbols on the machine ………………………10

5. For safe operation ………………………………12

6. Set up ……………………………………………22

7. Fuel ………………………………………………24

8. Operation …………………………………………30

9. Maintenance ……………………………………36

10. Storage……………………………………………46

11. Troubleshooting guide …………………………48

12. Parts list …………………………………………49

Contents

English

3

SECURITE

Les instructions contenues dans les mises en

garde de ce mode d’emploi portant le symbole

concernent les points critiques qui doivent être

pris en considération pour éviter les blessures

corporelles graves, c’est pourquoi ces précautions

doivent être rigoureusement suivies.

■ DIFFERENTS TYPES D’AVERTISSEMENT DE CE

MODE D’EMPLOI

Les instructions repérées par ce symbole doivent être

rigoureusement suivies afin d’éviter tout accident

pouvant entraîner des blessures corporelles graves ou

la mort.

Les instructions repérées par ce symbole doivent être

suivies afin d’éviter tout incident mécanique, panne ou

endommagement de la coupe-bordures.

Remarques utilisées dans des instructions ou conseils

supplémentaires pour l’utilisation de cette coupe-

bordures.

REMARQUE

IMPORTANT

AVERTISSEMENT

LA SEGURIDAD PRIMERO

Las instrucciones que aparecen en este manual

bajo las advertencias marcadas con el símbolo

hacen referencia a puntos críticos que deben

tomarse en consideración para evitar posibles

lesiones físicas; por esta razón, le solicitamos que

lea detenidamente todas estas instrucciones y que

las siga estrictamente.

■ ADVERTENCIAS CONTENIDAS EN EL MANUAL

Bajo este símbolo aparecen instrucciones que se

deben seguir a fin de evitar accidentes que pueden

causar serias lesiones físicas o la muerte.

Bajo este símbolo aparecen instrucciones importantes

que se deben seguir; ignorar estas instrucciones

puede ocasionar fallos mecánicos, desperfectos o

daños.

Este símbolo hace referencia a consejos o

indicaciones que son de utilidad para el uso del

producto.

NOTA

IMPORTANTE

ADVERTENCIA

1. Emplacement des composants...........................5

2. Caracteristiques..................................................5

3.

Etiquettes d’avertissement placées sur la machine

..11

4. Symboles utilises sur la machine......................11

5. Consignes de securite ......................................13

6. Assemblage......................................................23

7. Carburant..........................................................25

8. Fonctionnement................................................31

9. Entretien ...........................................................37

10. Rangement .......................................................47

11. Guide de localisation des pannes.....................48

12. Liste des pièces................................................49

1. Posición de las piezas ........................................5

2. Especificaciones.................................................5

3. Etiqueta de advertencias en la máquina...........11

4. Símbolos presentes en la máquina ..................11

5. Instrucciones de seguridad...............................13

6. Montaje.............................................................23

7. Combustible......................................................25

8. Uso ...................................................................31

9. Mantenimiento ..................................................37

10. Almacenamiento...............................................47

11.

Guía de localización y solución de problemas

......

48

12. Lista de piezas..................................................49

Tables des matieres Contenido

Français Español

4

1. Parts location

English

■ HEZ2401S

Overall size(LxWxH) ············································································· 72.6 (1845) x 9.5 (240) x 12.8 (325) in (mm)

Dry weight w/o acc. ······················································································································ 14.9 (6.75) lbs (kg)

Engine Type·················································································································· Air-cooled 2-stroke gasoline

Model·································································································································· Zenoah GZ23N8

Displacement ·················································································································· 1.5cu-in (23.6 cm

3

)

Max. output ························································································ 1.15Hp (0.858kW) at 8000 min

-1

(rpm)

Idle speed····················································································································· 3000±200 min

-1

(rpm)

Fuel ··················································································································· Mixture(Gasoline 50 : Oil 1)

···············································································································(when using ZENOAH genuine oil)

Carburetor ··············································································································· Walbro Diaphragm type

Spark plug ························································································································CHAMPION RZ7C

Fuel tank capacity····························································································································21.3 fl.oz (0.63 )

Transmission ······················································· Centrifugal clutch, Rigid driveshaft, Bevel gears (Angle : 90 deg.)

Reduction ratio ······································································································································ 2.538 (33.13)

Cutting head rotating direction··················································································· Clockwise (Vew against blade)

Durability period············································································································································· 300 hrs.

Blade length ···································································································································7.87 (200) in (mm)

Use for ·················································································································································· Lawn edging

Standard Accessories

Goggle··················································································································································· 1 pc.

Tool Kit ·················································································································································· 1 pc.

Specifications are subject to change without notice.

1. Loop handle

2. Ignition switch

3. Throttle cable

4. Throttle lever

5. Throttle set button

6. Blade guard

7. Blade

8. Wheel

9. Spark arrester

10. Starter knob

11. Fuel tank

12. Primer pump

13. Choke lever

14. Air cleaner cover

2. Specifications

5

1. Emplacement des pieces 1. Situación de las piezas

Français Español

1. Poignée

2. Bouton d’allumage

3. Câble d’accélérateur

4. Levier d’accélération

5. Manette des gaz

6. Garde-lame

7. Lame

8. Roues

9. Pare-étincelles du silencieux

10. Poignée de démarrage

11. Réservoir de carburant

12. Pompe d’amorçage

13. Levier de starter

14. Capot du filtre à air

1. Mango

2. Interruptor de encendido

3. Cable del acelerador

4. Palanca del acelerador

5. Botón de acelerador

6. Protector de la cuchilla

7. Cuchilla

8. Rueda

9. Parachispas

10. Arrancador

11. Tanque de combustible

12. Cebador

13. Palanca del estrangulador

14. Cubierta del filtro de aire

Français

2. Fiche technique

■ HEZ2401S

Dimensions totales (L x L x H) ································································································· 1845 x 240 x 325 mm

Poids à sec sans acc. ······································································································································6,75 kg

Moteur Type········································································································· 2 temps à essence refroidi par air

Modèle································································································································ Zenoah GZ23N8

Cylindrée ··········································································································································23,6 cm

3

Puissance maximale··················································································· 1,15 CV (0,858kW) à 8000 t/mn

Vitesse de ralenti··················································································································· 3000±200 t/mn

Carburant ····································································································· Mélange (essence 50 : huile 1)

(Lors de l’utilisation de la véritable huile ZENOAH)

Carburateur················································································································· Walbro à diaphragme

Bougie d’allumage··········································································································· CHAMPION RZ7C

Contenance du réservoir de carburant ············································································································· 0,63

Transmission················· Embrayage centrifuge, arbre de transmission rigide, engrenage conique (angle : 90 deg.)

Rapport de réduction····························································································································· 2,538 (33,13)

Sens de rotation de la tête de coupe············································ Sens des aiguilles d’une montre (Vue de la lame)

Période de durabilité································································································································· 300 heures

Longueur de lame···········································································································································200 mm

Utiliser pour ··············································································································Couper les bordures de pelouse

Standard Accessories

Lunettes de sécurité ······························································································································ 1 pc.

Trousse à outils ····································································································································· 1 pc.

Ces spécifications peuvent être modifiées sans préavis.

Español

2. Especificaciohes

■ HEZ2401S

Tamaño global (Long x Anch x Alt) ·························································································· 1845 x 240 x 325 mm

Peso en seco sin acc. ····································································································································· 6,75 kg

Motor Tipo ························································································· Refrigerado por aire / gasolina de 2 tiempos

Modelo ······························································································································· Zenoah GZ23N8

Desplazamiento······························································································································· 23,6 cm

3

Potencia máxima ························································································ 1,15 Hp (0,858kW) a 8000 rpm

Velocidad de marcha en vacío ······························································································ 3000±200 rpm

Combustible ······························································································· Mezcla (Gasolina 50: Aceite 1)

(al utilizar el aceite auténtico de ZENOAH)

Carburador ··············································································································· Walbro tipo Diafragma

Bujía ······································································································································· NGK CMR7H

Capacidad del depósito de combustible··········································································································· 0,63

Transmisión ······································ Embrague centrífugo, eje propulsor rígido, cambios bisel (Ángulo:90 grados)

Relación de reducción··························································································································· 2,538 (33,13)

Dirección de rotación de cabeza cortador··········· Sentido de las agujas del reloj (Vista mirando hacia las cuchillas)

Período de duración ···········································································································································300 h

Largo del cuchilla············································································································································200 mm

Utilizar para ···································································································································Recorte de césped

Standard Accessories

Gafas protectoras·································································································································· 1 pc.

Caja de herramientas ···························································································································· 1 pc.

Especificaciones sujetas a cambios sin previo aviso.

6

English

■ HEZ2602S

Overall size(LxWxH) ············································································· 73.0 (1855) x 9.3 (235) x 13.0 (330) in (mm)

Dry weight w/o acc. ······················································································································ 15.0 (6.82) lbs (kg)

Engine Type·················································································································· Air-cooled 2-stroke gasoline

Model································································································································ Zenoah GZ25N25

Displacement ·················································································································· 1.6cu-in (25.4 cm

3

)

Max. output ······························································································ 1.2Hp (0.9kW) at 7500 min

-1

(rpm)

Idle speed····················································································································· 3000±200 min

-1

(rpm)

Fuel ··················································································································· Mixture(Gasoline 50 : Oil 1)

···············································································································(when using ZENOAH genuine oil)

Carburetor ··············································································································· Walbro Diaphragm type

Spark plug ································································································································NGK CMR7H

Fuel tank capacity····························································································································22.0 fl.oz (0.65 )

Transmission ······················································· Centrifugal clutch, Rigid driveshaft, Bevel gears (Angle : 90 deg.)

Reduction ratio ······································································································································ 2.538 (33.13)

Cutting head rotating direction··················································································· Clockwise (Vew against blade)

Durability period············································································································································· 300 hrs.

Blade length ···································································································································7.87 (200) in (mm)

Use for ·················································································································································· Lawn edging

Standard Accessories

Goggle··················································································································································· 1 pc.

Tool Kit ·················································································································································· 1 pc.

Specifications are subject to change without notice.

2. Specifications

7

Français

2. Fiche technique

■ HEZ2602S

Dimensions totales (L x L x H) ································································································· 1855 x 235 x 330 mm

Poids à sec sans acc. ······································································································································6,82 kg

Moteur Type········································································································· 2 temps à essence refroidi par air

Modèle······························································································································ Zenoah GZ25N25

Cylindrée ··········································································································································25.4 cm

3

Puissance maximale························································································· 1,2 CV (0,9kW) à 7500 t/mn

Vitesse de ralenti··················································································································· 3000±200 t/mn

Carburant ····································································································· Mélange (essence 50 : huile 1)

(Lors de l’utilisation de la véritable huile ZENOAH)

Carburateur················································································································· Walbro à diaphragme

Bougie d’allumage ··················································································································· NGK CMR7H

Contenance du réservoir de carburant ············································································································· 0,65

Transmission················· Embrayage centrifuge, arbre de transmission rigide, engrenage conique (angle : 90 deg.)

Rapport de réduction····························································································································· 2,538 (33,13)

Sens de rotation de la tête de coupe············································ Sens des aiguilles d’une montre (Vue de la lame)

Période de durabilité································································································································· 300 heures

Longueur de lame···········································································································································200 mm

Utiliser pour ··············································································································Couper les bordures de pelouse

Standard Accessories

Lunettes de sécurité ······························································································································ 1 pc.

Trousse à outils ····································································································································· 1 pc.

Ces spécifications peuvent être modifiées sans préavis.

Español

2. Especificaciohes

■ HEZ2602S

Tamaño global (Long x Anch x Alt) ·························································································· 1855 x 235 x 330 mm

Peso en seco sin acc. ····································································································································· 6,82 kg

Motor Tipo ························································································· Refrigerado por aire / gasolina de 2 tiempos

Modelo ····························································································································· Zenoah GZ25N25

Desplazamiento······························································································································· 25,4 cm

3

Potencia máxima ······························································································ 1,2 Hp (0,9kW) a 7500 rpm

Velocidad de marcha en vacío ······························································································ 3000±200 rpm

Combustible ······························································································· Mezcla (Gasolina 50: Aceite 1)

(al utilizar el aceite auténtico de ZENOAH)

Carburador ··············································································································· Walbro tipo Diafragma

Bujía ······································································································································· NGK CMR7H

Capacidad del depósito de combustible··········································································································· 0,65

Transmisión ······································ Embrague centrífugo, eje propulsor rígido, cambios bisel (Ángulo:90 grados)

Relación de reducción··························································································································· 2,538 (33,13)

Dirección de rotación de cabeza cortador··········· Sentido de las agujas del reloj (Vista mirando hacia las cuchillas)

Período de duración ···········································································································································300 h

Largo del cuchilla············································································································································200 mm

Utilizar para ···································································································································Recorte de césped

Standard Accessories

Gafas protectoras·································································································································· 1 pc.

Caja de herramientas ···························································································································· 1 pc.

Especificaciones sujetas a cambios sin previo aviso.

8

English

■ HEZ3001S

Overall size(LxWxH) ············································································· 73.0 (1855) x 9.5 (240) x 13.2 (335) in (mm)

Dry weight w/o acc. ······················································································································ 14.9 (6.74) lbs (kg)

Engine Type·················································································································· Air-cooled 2-stroke gasoline

Model·································································································································· Zenoah GZ30N1

Displacement ·················································································································· 1.8cu-in (29.5 cm

3

)

Max. output ······························································································ 1.4Hp (1.0kW) at 8500 min

-1

(rpm)

Idle speed····················································································································· 3000±200 min

-1

(rpm)

Fuel ··················································································································· Mixture(Gasoline 50 : Oil 1)

···············································································································(when using ZENOAH genuine oil)

Carburetor ··············································································································· Walbro Diaphragm type

Spark plug ································································································································NGK CMR7H

Fuel tank capacity····························································································································24.3 fl.oz (0.72 )

Transmission ······················································· Centrifugal clutch, Rigid driveshaft, Bevel gears (Angle : 90 deg.)

Reduction ratio ······································································································································ 2.538 (33.13)

Cutting head rotating direction··················································································· Clockwise (Vew against blade)

Durability period············································································································································· 300 hrs.

Blade length ···································································································································7.87 (200) in (mm)

Use for ·················································································································································· Lawn edging

Standard Accessories

Goggle··················································································································································· 1 pc.

Tool Kit ·················································································································································· 1 pc.

Specifications are subject to change without notice.

2. Specifications

9

Français

2. Fiche technique

■ HEZ3001S

Dimensions totales (L x L x H) ································································································· 1855 x 240 x 335 mm

Poids à sec sans acc. ······································································································································6,74 kg

Moteur Type········································································································· 2 temps à essence refroidi par air

Modèle································································································································ Zenoah GZ30N1

Cylindrée ··········································································································································29,5 cm

3

Puissance maximale························································································· 1,4 CV (1,0kW) à 8500 t/mn

Vitesse de ralenti··················································································································· 3000±200 t/mn

Carburant ····································································································· Mélange (essence 50 : huile 1)

(Lors de l’utilisation de la véritable huile ZENOAH)

Carburateur················································································································· Walbro à diaphragme

Bougie d’allumage ··················································································································· NGK CMR7H

Contenance du réservoir de carburant ············································································································· 0,72

Transmission················· Embrayage centrifuge, arbre de transmission rigide, engrenage conique (angle : 90 deg.)

Rapport de réduction····························································································································· 2,538 (33,13)

Sens de rotation de la tête de coupe············································ Sens des aiguilles d’une montre (Vue de la lame)

Période de durabilité································································································································· 300 heures

Longueur de lame···········································································································································200 mm

Utiliser pour ··············································································································Couper les bordures de pelouse

Standard Accessories

Lunettes de sécurité ······························································································································ 1 pc.

Trousse à outils ····································································································································· 1 pc.

Ces spécifications peuvent être modifiées sans préavis.

Español

2. Especificaciohes

■ HEZ3001S

Tamaño global (Long x Anch x Alt) ·························································································· 1855 x 240 x 335 mm

Peso en seco sin acc. ····································································································································· 6,74 kg

Motor Tipo ························································································· Refrigerado por aire / gasolina de 2 tiempos

Modelo ······························································································································· Zenoah GZ30N1

Desplazamiento······························································································································· 29,5 cm

3

Potencia máxima ······························································································ 1,4 Hp (1.0kW) a 8500 rpm

Velocidad de marcha en vacío ······························································································ 3000±200 rpm

Combustible ······························································································· Mezcla (Gasolina 50: Aceite 1)

(al utilizar el aceite auténtico de ZENOAH)

Carburador ··············································································································· Walbro tipo Diafragma

Bujía ······································································································································· NGK CMR7H

Capacidad del depósito de combustible··········································································································· 0,72

Transmisión ······································ Embrague centrífugo, eje propulsor rígido, cambios bisel (Ángulo:90 grados)

Relación de reducción··························································································································· 2,538 (33,13)

Dirección de rotación de cabeza cortador··········· Sentido de las agujas del reloj (Vista mirando hacia las cuchillas)

Período de duración ···········································································································································300 h

Largo del cuchilla············································································································································200 mm

Utilizar para ···································································································································Recorte de césped

Standard Accessories

Gafas protectoras·································································································································· 1 pc.

Caja de herramientas ···························································································································· 1 pc.

Especificaciones sujetas a cambios sin previo aviso.

3. Warning labels on the machine

10

English

(1) Read owner's manual before operating this

machine.

(2) Wear head, eye and ear protection.

(3) Warning/Attention

(4) Keep all children, bystanders and helpers 15

meters away from the stick edgers.

If warning label peel off or become soiled and

impossible to read, you should contact the dealer from

which you purchased the product to order new labels

and affix them in the required location(s).

Never modify your stick edgers.

We won't warrant the machine, if you use the

remodeled stick edgers or you don't observe the

proper usage written in the manual.

WARNING

IMPORTANT

For safe operation and maintenance, symbols are

carved in relief on the machine. According to these

indications, please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

(c) The direction to open the choke

Position:

AIR CLEANER COVER

IMPORTANT ENGINE INFORMATION

ENGINE FAMILY : 6KZXS.0254BG ; EM

ENGINE DISPLACEMENT : 25cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED :

THIS ENGINE MEETS U.S. EPA PH2

AND 2006 CALIFORNIA EMISSION

REGULATIONS FOR SI SORE’s.

COMPLIANCE PERIOD : CATEGORY A

■ EMISSION CONTROL

An emission control label is located on the engine.

4. Symbols on the machine

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 AND 2006

CALIFORNIA EMISSION REGULATIONS FOR SI

SORE’s. COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS.0244XY ; EM

ENGINE DISPLACEMENT : 24cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

MADE IN JAPAN

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 AND 2006

CALIFORNIA EMISSION REGULATIONS FOR SI

SORE’s. COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS.0294NO ; EM

ENGINE DISPLACEMENT : 29.5cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

MADE IN JAPAN

[HEZ2401S]

[HEZ3001S]

[HEZ2602S]

3. Etiqueta de advertencia en la máquina

3. Etiquettes d’avertissement sur la machine

11

Français Español

(1) Lire le mode d’emploi avant d’utiliser cette

machine.

(2) Porter un casque de sécurité, des lunettes de

sécurité et un casque antibruit.

(3) Avertissement/Attention

(4) Interdire aux enfants ou à toute personne de

s’approcher dans un rayon de 15 mètres de la

coupe-bordures.

Si les étiquettes d’avertissement se décollent,

deviennent sales ou impossible à lire, commander de

nouvelles étiquettes auprès du revendeur pour les

remplacer.

Ne pas modifier la coupe-bordures.

La garantie sera annulée si la coupe-bordures a été

modifiée ou utilisée de manière non conforme aux

instructions de ce mode d’emploi.

AVERTISSEMENT

IMPORTANT

(1) Lea el manual de instrucciones antes de usar

esta máquina.

(2) Use protección para la cabeza, ojos y oídos.

(3) Advertencia/Atención

(4) Mantenga a niños, espectadores y ayudantes a

una distancia de 15 metros del cortacéspedes.

Si las etiquetas de advertencia se desprenden o se

manchan y se vuelven ilegibles, contacte al distribuidor

donde adquirió el producto y solicite nuevas etiquetas.

Fije las nuevas etiquetas en las posiciones

correspondientes.

Nunca haga ningún tipo de modificación al

cortacéspedes.

No podemos garantizar la máquina si usted utiliza

el cortacéspedes remodelado o si no sigue las

instrucciones de uso contenidas en este manual.

ADVERTENCIA

IMPORTANTE

TYPE DE MOTEUR : 6KZXS.0254BG ; EM

CYLINDREE DU MOTEUR : 25 cc

SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES

SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.

FABRIQUE PAR :

INFORMATION IMPORTANTE

CONCERNANT LE MOTEUR

CE MOTEUR EST CONFORME AUX

REGLEMENTS SUR LES EMISIONS DE GAZ U.S.

EPA PH2 ET 2006 DE LA CALIFORNIE POUR UNE

PERIODE DE CONFORMITE SI SORE : CATEGORIE A

■ MESURES DE LUTTE CONTRE LES EMISSIONS

Une étiquette de mesures de lutte contre les émissions

se trouve sur le moteur.

■ CONTROL DE EMISIONES

El motor lleva una etiqueta de control de emisiones.

Des symboles en relief ont été placés sur la machine

pour assurer la sécurité à l’usage et faciliter l’entretien.

Prendre soin d’observer les indications suivantes afin

d’éviter les erreurs.

(a) Emplacement de remplissage du “MELANGE”

Emplacement:

BOUCHON DU RESERVOIR DE CARBURANT

(b) Position fermée du starter

Emplacement:

CAPOT DU FILTRE A AIR

(c) Position ouverte du starter

Emplacement:

CAPOT DU FILTRE A AIR

Para el uso y mantenimiento seguro del producto, los

símbolos han sido estampados en relieve en la

máquina. Siga siempre estas indicaciones, y tenga

cuidado de no cometer un error.

(a) Orificio de llenado de “MEZCLA DE GASOLINA”

Posición:

TAPÓN DEL TANQUE DE COMBUSTIBLE

(b) Dirección de cierre del estrangulador

Posición:

CUBIERTA DEL FILTRO DE AIRE

(c) Dirección de apertura del estrangulador

Posición:

CUBIERTA DEL FILTRO DE AIRE

INFORMACIÓN IMPORTANTE

ACERCA DEL MOTOR

TIPO DE MOTOR : 6KZXS.0254BG ; EM

CILINDRADA DEL MOTOR : 25cc

CONSULTE EL MANUAL DEL PROPIETARIO PARA LAS

ESPECIFICACIONES Y AJUSTES DE MANTENIMIENTO.

FABRICADO POR :

ESTE MOTOR CUMPLE CON LAS

NORMAS SOBRE EMISIONES U.S. EPA PH2

Y 2006 DE CALIFORNIA PARA EL PERÍODO

DE CONFORMIDAD “SI SORE”: CATEGORÍA A

4. Symboles utilises sur la machine 4. Símbolos presentes en la máquina

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

CE MOTEUR EST CONFORME AUX REGLEMENTS SUR LES

EMISIONS DE GAZ U.S. EPA PH2 ET 2006 DE LA CALIFORNIE

POUR UNE PERIODE DE CONFORMITE SI SORE: CATEGORIE A

TYPE DE MOTEUR : 6KZXS.0244XY ; EM

CYLINDREE DU MOTEUR : 24 cc

SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES

SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.

FABRIQUE PAR :

MADE IN JAPAN

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 AND 2006

CALIFORNIA EMISSION REGULATIONS FOR SI

SORE’s. COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS.0294NO ; EM

ENGINE DISPLACEMENT : 29.5cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

MADE IN JAPAN

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

CE MOTEUR EST CONFORME AUX REGLEMENTS SUR LES

EMISIONS DE GAZ U.S. EPA PH2 ET 2006 DE LA CALIFORNIE

POUR UNE PERIODE DE CONFORMITE SI SORE: CATEGORIE A

TYPE DE MOTEUR : 6KZXS.0244XY ; EM

CYLINDREE DU MOTEUR : 24 cc

SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES

SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.

FABRIQUE PAR :

MADE IN JAPAN

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 AND 2006

CALIFORNIA EMISSION REGULATIONS FOR SI

SORE’s. COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS.0294NO ; EM

ENGINE DISPLACEMENT : 29.5cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

MADE IN JAPAN

[HEZ2401S]

[HEZ3001S]

[HEZ2602S]

[HEZ2401S]

[HEZ3001S]

[HEZ2602S]

12

1. Read this manual carefully until you completely

understand and follow all safety and operating

instructions.

2. Keep this manual handy so that you may refer to

it later whenever any questions arise. Also note, if

you have any questions which cannot be

answered herein, contact the dealer from whom

you purchased the product.

3. Always be sure to include this manual when

selling, lending, or otherwise transferring the

ownership of this product.

4. Never allow children or anyone unable to fully

understand the directions given in the manual to

use the machine.

■ WORKING CONDITION

1. When using the product, you should wear proper

clothing and protective equipment.

(1) Helmet

(2) Ear protectors

(3) Protection goggles or face protector

(4) Thick work gloves

(5) Non-slip-sole work boots

2. And you should carry with you.

(1) Attached tools and files

(2) Properly reserved fuel

(3) Spare blade or nylon string

(4) Things to notify your working area (rope, warning

signs)

(5) Whistle (for collaboration or emergency)

(6) Hatchet or saw (for removal of obstacles)

3. Do not wear loose clothing, jewelry, short trousers,

sandals, or go barefoot. Do not wear anything which

might be caught by a moving part of the unit. Secure

hair so it is above shoulder length.

■ WORKING CIRCUMSTANCE

1. Never start the engine inside a closed room or

building. Exhaust gases contain dangerous carbon

monoxide.

2. Never use the product,

a. when the ground is slippery or when you can’t

maintain a steady posture.

b. At night, at times of heavy fog, or at any other

times when your field of vision might be limited

and it would be difficult to gain a clear view of the

working area.

c. During rain storms, during lightning storms, at

times of strong or gale-force winds, or at any

5. For safe operation

English

13

1. Lea detenidamente este manual hasta

comprender cabalmente todas las instrucciones

de seguridad y uso.

2. Mantenga este manual a mano para que pueda

consultarlo cuando tenga alguna duda. Si tiene

cualquier duda que no esté cubierta en este

manual, consulte en la tienda donde adquirió el

producto.

3. Asegúrese de incluir siempre este manual al

vender, prestar o transferir la propiedad de este

producto.

4. Nunca permita que niños u otras personas que

no sean capaces de comprender cabalmente las

instrucciones que se dan en el manual utilicen la

máquina.

■ CONDICIONES DE TRABAJO

1.Al utilizar el producto, asegúrese de usar la

vestimenta y el equipo de protección adecuados.

(1) Casco

(2) Protectores para los oídos

(3) Gafas protectoras o protector facial

(4) Guantes de trabajo gruesos

(5) Botas de trabajo con suela antideslizante

2 Asegúrese de llevar con usted los siguientes

elementos:

(1) Herramientas y limas incluidas

(2) Combustible de reserva

(3) Hoja de repuesto

(4) Elementos para marcar su área de trabajo

(cuerdas, letreros de advertencia)

(5) Silbato (para colaboración o situaciones de

emergencia)

(6) Hacha pequeña o sierra (para quitar obstáculos)

3. No use ropa suelta, joyas, pantalones cortos ni

sandalias, y no trabaje descalzo. No use nada que

pueda ser atrapado por las piezas móviles de la

unidad. Recójase el pelo, asegurándose de que

quede por encima de sus hombros.

■ PRECAUCIONES

1. Nunca arranque el motor dentro de una habitación

cerrada o edificio. Los gases de escape contienen

monóxido de carbono peligroso.

2. Nunca use el producto en los siguientes casos:

a. Cuando el suelo sea resbaloso o cuando usted

no pueda mantener una posición estable.

b. Durante la noche, cuando haya niebla densa, o

en cualquier otra situación en que su campo de

visión esté limitado y sea difícil lograr una

adecuada visión del área de trabajo.

c. Durante tormentas de lluvia, tormentas

eléctricas, tormentas de viento, o en cualquier

1. Lire ce manuel attentivement jusqu’à une

compréhension totale et suivre toutes les

instructions de sécurité et d’utilisation.

2. Conserver ce mode d’emploi à portée de la main

pour le consulter au moindre doute. Si une

question reste sans réponse, contacter le

revendeur.

3. Ne pas oublier de donner le manuel avec la

machine en cas de revente ou de prêt.

4. Ne pas laisser des enfants ou toute personne

incapable de comprendre les instructions, utiliser

cette machine.

■ CONDITIONS DE TRAVAIL

1. Lors de l’utilisation de cette machine, il est

nécessaire de porter des vêtements appropriés et

des équipements de sécurité.

(1) Casque

(2) Casque antibruit

(3) Lunettes ou masque de protection

(4) Gants de travail épais

(5)

Chaussures de sécurité à semelle antidérapante

2. Les objets suivants doivent être emportés sur le lieu

de travail :

(1) Les outils fournis avec la machine et des limes

(2) Une réserve de carburant

(3) Une lame de rechange

(4) Matériel pour délimiter la zone de travail

(5) Un sifflet (pour collaborateur ou en cas

d’urgence)

(6) Une hache ou une scie (pour enlever les

obstacles)

3. Ne pas porter des vêtements lâches, de short, de

bijou, de sandales ou travailler pieds nus. Ne pas

porter quoi que ce soit pouvant être happé par les

pièces en mouvement de la machine. Porter les

cheveux longs noués au-dessus des épaules.

■ CONDITIONS DE TRAVAIL

1. Ne jamais mettre la machine en marche à l’intérieur

d’une pièce ou d’un bâtiment. Les gaz

d’échappement contiennent du monoxide de

carbone dangereux.

2. Ne jamais utiliser la machine dans les conditions

suivantes:

a. Lorsque le sol est glissant ou lorsqu’il est

impossible de se maintenir dans une position

correcte.

b. La nuit, par temps de brouillard ou lorsque la

visibilité ou le champ de vision empêche de voir

clairement la zone de travail.

5. Consignes de securite 5. Instrucciones de seguridad

Français Español

14

other times when weather conditions might make

it unsafe to use the product.

■ WORKING PLAN

1. You should never use the product when under the

influence of alcohol, when suffering from exhaustion

or lack of sleep, when suffering from drowsiness as

a result of having taken cold medicine or at any

other time when a possibility exists that your

judgment might be impaired or that you might not be

able to operate the product properly and in a safe

manner.

2. When planning your work schedule, allow plenty of

time to rest. Limit the amount of time over which the

product is to be used continuously to somewhere

around 30~40 minutes per session, and take 10~20

minutes of rest between work sessions. Also try to

keep the total amount of work performed in a single

day under 2 hours or less.

1. If you don’t observe the working time, or working

manner (See ■ USING THE PRODUCT),

Repetitive Stress Injury(RSI) could occur.

If you feel discomfort, redness and swelling of

your fingers or any other part of your body, see a

doctor before getting worse.

2. To avoid noise complaints, in general, operate

product between 8a.m. and 5p.m. on weekdays

and 9a.m. to 5p.m. weekends.

Check and follow the local regulations as to sound

level and hours of operations for the product.

■ BEFORE STARTING THE ENGINE

1. The area within a perimeter of 50 feet (15m) of the

person using the product should be considered a

hazardous area into which no one should enter. If

necessary yellow warning rope, warning signs

should be placed around the perimeter of the area.

When work is to be performed simultaneously by two

or more persons, care should also be taken to

constantly look around or otherwise check for the

presence and locations of other people working so

as to maintain a distance between each person

sufficient to ensure safety.

2. Check the condition of working area to avoid any

accident by hitting hidden obstacles such as stumps,

stones, cans, or broken grass.

NOTE

WARNING

5. For safe operation

English

c. Pendant les averses, les orages avec éclairs, par

grands vents ou toute autre condition climatique

rendant l’utilisation de la machine dangereuse.

■ PLAN DE TRAVAIL

1. Ne jamais utiliser la machine sous l’influence de

l’alcool ou en état de faiblesse due à la fatigue, au

manque de sommeil, à la prise de médicament ou à

tout autre moment où l’on n’est pas réellement

capable de l’utiliser correctement et en toute

sécurité.

2. Lors de l’élaboration du plan de travail, prévoir

suffisamment de temps de repos. Limiter la durée

des périodes pendant lesquelles la machine est

utilisée sans interruption entre 30 et 40 minutes. Se

reposer de 10 à 20 minutes entre ces périodes.

Autant que possible, essayer de limiter ce genre de

travail à 2 heures par jour.

1. Si ce plan de travail et cette méthode de travail

ne sont pas respectés, un accident dû au stress

répétitif peut se produire (voir ■ UTILISATION

DE LA MACHINE).

Si l’on ressent un malaise ou si les doigts ou

tout autre membre rougissent et enflent,

consulter un docteur avant que cela ne

s’aggrave.

2. Pour éviter les problèmes de bruit avec le

voisinage, utiliser généralement la machine entre

8 et 17 heures pendant la semaine et de 9 à 17

heures les fins de semaine.

Vérifier et suivre la réglementation locale sur le niveau

de bruit et les horaires d’utilisation de ce type de

machine.

■ AVANT DE METTRE LE MOTEUR EN MARCHE

1. La zone dans un rayon de 15 mètres autour de

l’opérateur est considérée comme dangereuse et

personne ne doit s’y trouver. Si nécessaire, délimiter

le périmètre de la zone de travail avec du ruban de

marquage (rouge fluorescent et blanc par exemple)

et poser des panneaux d’avertissement. Lorsque

deux ou plusieurs personnes travaillent ensemble ou

à proximité, chacune doit constamment faire

attention et garder ses distances par rapport aux

autres pour assurer une sécurité satisfaisante.

2. Vérifier constamment l’état de la zone de travail pour

éviter tout accident dû aux impacts avec des

obstacles tels que les souches, les pierres, les

boîtes de conserves ou débris de verre.

REMARQUE

AVERTISSEMENT

otra circunstancia en que las condiciones

climáticas puedan hacer inseguro el uso del

producto.

■ PLAN DE TRABAJO

1. Nunca utilice el producto cuando se encuentre bajo

la influencia del alcohol, cuando sufra de fatiga o

falta de sueño, cuando sienta somnolencia debido a

que ha tomado una medicina para el resfrío, o en

cualquier otra situación que pueda afectar su juicio y

usted no sea capaz de utilizar el producto

correctamente y de manera segura.

2. Al planificar su trabajo, deje un tiempo suficiente

para descansar. Limite el tiempo de uso continuo del

producto a 30–40 minutos por sesión, y tome

descansos de 10–20 minutos entre las sesiones de

trabajo. Asimismo, trate de que la cantidad total de

trabajo diario sea inferior a 2 horas.

1. Si no sigue las recomendaciones en cuanto a la

duración del trabajo o a la forma de trabajar

(consulte ■ USO DEL PRODUCTO), usted podrá

sufrir una lesión por esfuerzo repetido (RSI).

Si siente algún malestar, si sus dedos o

cualquier otra parte de su cuerpo enrojecen o se

hinchan, consulte oportunamente a un médico.

2. Para evitar problemas de ruido, en general utilice

el producto entre las 8 a.m. y las 5 p.m. los días

laborables, y de 9 a.m. a 5 p.m. durante el fin de

semana.

Compruebe y respete las disposiciones locales

respecto de los niveles de ruido y horas de uso del

producto.

■ ANTES DE ARRANCAR EL MOTOR

1. El área dentro de un perímetro de 15 m de la

persona que está usando el producto debe

considerarse como un área de peligro en la que

nadie debe ingresar. Si fuera necesario, marque el

perímetro del área de trabajo con una cuerda de

color amarillo y letreros de advertencia. Cuando el

trabajo vaya a ser realizado simultáneamente por

dos o más personas, también se deberá tener la

precaución de mirar constantemente alrededor y

verificar la presencia y posición de las demás

personas que están trabajando, a fin de mantener

una distancia prudente entre cada persona que

garantice su seguridad.

2. Compruebe las condiciones del área de trabajo a fin

de evitar accidentes que pueden ocurrir al golpear

obstáculos ocultos tales como tocones, piedras,

latas o vidrios rotos.

NOTA

ADVERTENCIA

5. Consignes de securite 5. Instrucciones de seguridad

Français Español

15

16

Remove any obstacle before beginning work.

3. Inspect the entire unit for loose fasteners and fuel

leakage. Make sure that the cutting attachment is

properly installed and securely fastened.

4. Be sure the debris guard is firmly attached in place.

5. If the cutting head is the metal blade, change the

guard and handle, and attach the shoulder strap

(see p42). Adjust the strap before starting the engine

at the position that your left hand can comfortably

hold the handlebar grip approximately waist high.

■ STARTING THE ENGINE

1. Keep bystanders and animals at least 50feet (15m)

away from the operating point. If you are

approached, immediately stop the engine.

2. The product is equipped with a centrifugal clutch

mechanism, so the cutting attachment could rotate

as soon as the engine is started. When starting the

engine, place the product onto the ground in a flat

clear area and hold it firmly in place so as to ensure

that neither the cutting part nor the throttle come into

contact with any obstacle when the engine starts.

Make sure the throttle is at idle position.

Never place the throttle into the high speed

position or half throttle position (throttle lock

position) when starting the engine.

3. After starting the engine, check to make sure that

the cutting attachment stops rotating when the

throttle is moved fully back to its original position

(idle position). If it continues to rotate even after the

throttle has been moved fully back, turn off the

engine and take the unit to your authorized Red Max

servicing dealer for repair.

■ USING THE PRODUCT

Cut only materials recommended by the

manufacturer. And use only for tasks explained in

the manual.

IMPORTANT

WARNING

IMPORTANT

5. For safe operation

English

17

Retirer tout obstacle avant de commencer le travail.

3. Vérifier que la machine ne comporte aucun élément

desserré ou de fuite de carburant. S’assurer que

l’outil de coupe est monté correctement et bien

serré.

4. S'assurer que le cache de protection anti-débris est

fermement attaché.

5. Si la tête de coupe est la lame en métal, changer le

cache et la poignée et fixer le harnais (voir page 43).

Régler le harnais avant de démarrer le moteur en

l’ajustant de sorte que votre main gauche puisse

tenir confortablement la poignée environ à hauteur

de la taille.

■ DEMARRAGE DU MOTEUR

1. Empêcher toute personne ou animal de s’approcher

à moins de 15 mètres. Si quelqu’un s’approche trop

près, arrêter aussitôt le moteur.

2. La machine est équipée d’un embrayage centrifuge

et l’outil de coupe se met à tourner dès que le

moteur est mis en route en plaçant l’accélérateur en

position de démarrage. Pour mettre le moteur en

route, poser et maintenir fermement la machine à

plat sur le sol dans un endroit dégagé où aucun

obstacle ne peut entrer en contact avec l’outil de

coupe ou la manette d’accélérateur une fois que le

moteur sera en marche.

Veiller à ce que la manette de l’accélérateur est au

ralenti.

Ne jamais mettre la manette de l’accélérateur à

fond ou à moitié enclenchée (Position de

verrouillage de la manette) lors de la mise en

marche.

3. Une fois le moteur en marche, vérifier que l’outil de

coupe s’arrête de tourner lorsque l’accélérateur est

remis à zéro. Si l’outil de coupe continue à tourner,

couper le moteur et rapporter l’appareil chez votre

revendeur Red Max agréé afin de le faire réparer.

■ UTILISATION DE LA MACHINE

Ne couper avec la machine que les matériaux

recommandés par le fabricant.

1. Tenir les poignées de la machine fermement des

IMPORTANT

AVERTISSEMENT

IMPORTANT

Quite todos los obstáculos antes de iniciar el trabajo.

3. Inspeccione la unidad completa para determinar si

tiene sujetadores sueltos o fugas de combustible.

Asegúrese de que el accesorio de corte esté

debidamente instalado y asegurado.

4. Asegúrese de que el protector contra desechos se

encuentra firmemente acoplado en su sitio.

5. Si el cabezal cortador es la hoja metálica, cambie el

protector y el mango y enganche la correa para

hombro (vea la p.43). Ajuste la correa antes de

arrancar el motor en una posición en la que su mano

izquierda pueda sujetar cómodamente la barra del

manillar aproximadamente a la altura de la cintura.

■ ARRANQUE DEL MOTOR

1. Mantenga a espectadores y animales a una

distancia de al menos 15 metros del lugar de uso de

la máquina. Si alguien se aproxima, detenga

inmediatamente el motor.

2. El producto está equipado con un mecanismo de

embrague magnético, por lo que el accesorio de

corte comienza a girar inmediatamente cuando se

arranca el motor poniendo el acelerador en posición

de arranque. Al arrancar el motor, ponga el producto

en el suelo, en un lugar plano y despejado, y

sujételo firmemente para asegurarse de que la pieza

de corte y el acelerador no puedan entrar en

contacto con ningún obstáculo cuando el motor

arranque.

Asegúrese de que el acelerador esté en posición

de ralentí.

Nunca coloque el acelerador en la posición de alta

velocidad o aceleración media (posición de

bloqueo), al arrancar el motor.

3. Tras arrancar el motor, compruebe que el accesorio

de corte para de girar cuando se coloca el

acelerador totalmente en su posición inicial (en

ralentí). Si sigue girando incluso después de que el

acelerador vuelva a su posición inicial, apague el

motor y lleve la unidad a su centro de servicio Red

Max autorizado para que sea reparada.

■ USO DEL PRODUCTO

Corte sólo los materiales indicados por el

fabricante y use la máquina sólo para las tareas

descritas en este manual.

IMPORTANTE

ADVERTENCIA

IMPORTANTE

5. Consignes de securite 5. Instrucciones de seguridad

Français Español

18

1. Grip the handles firmly with both hands using your

whole hand. Place your feet slightly apart (slightly

further apart than the width of your shoulders) so

that your weight is distributed evenly across both

legs, and always be sure to maintain a steady, even

posture while working.

2. Keep cutting attachment below waist level.

3. Maintain the speed of the engine at the level

required to perform cutting work, and never raise the

speed of the engine above the level necessary.

4. If the unit start to shake or vibrate, turn off the

engine and check the whole unit. Do not use it until

the trouble has been properly corrected.

5. Keep all parts of your body away from rotating

cutting attachment and hot surfaces.

6. Never touch the muffler, spark plug, or other metallic

parts of the engine while the engine is in operation

or immediately after shutting down the engine. Doing

so could result in serious burns or electrical shock.

• IF SOMEONE COMES

1. Guard against hazardous situations at all times.

Warn adults to keep pets and children away from the

area. Be careful if you are approached. Injury may

result from flying debris.

2. If someone calls out or otherwise interrupts you

while working, always be sure to turn off the engine

before turning around.

■ MAINTENANCE

1. In order to maintain your product in proper working

order, perform the maintenance and checking

operations described in the manual at regular

intervals.

2. Always be sure to turn off the engine before

performing any maintenance or checking

procedures.

(1) Check ok !

The metallic parts reach high temperatures

immediately after stopping the engine.

3. When replacing the cutting attachment or any other

part, or when replacing the oil or any lubricant,

always be sure to use only RedMax products or

products which have been certified by RedMax

for use with the RedMax product.

4. In the event that any part must be replaced or any

maintenance or repair work not described in this

WARNING

5. For safe operation

English

19

deux mains. Ecarter légèrement les jambes (pour

que les pieds reposent sur une largeur un peu plus

importante que celle des épaules) et avoir une

posture de travail stable et répartir le poids du corps

également sur chaque jambe.

2. Maintenir l’outil de coupe toujours plus bas que le

niveau de la taille.

3. Faire tourner le moteur à la vitesse appropriée à la

coupe sans jamais accélérer inutilement au dessus

du niveau nécessaire.

4. Si la machine se met à vibrer ou à créer des

secousses, arrêter le moteur et procéder à une

vérification totale de la machine.

5. Se tenir à distance de l’outil de coupe ou des parties

chaudes de la machine.

6. Ne jamais toucher le silencieux, la bougie ou toute

autre partie métallique du moteur pendant le

fonctionnement ou aussitôt après son arrêt. Dans

ces circonstances, les risques de brûlures ou

d’électrocution sont importants.

• SI QUELQU’UN S’APPROCHE

1. Il faut se préserver des situations dangereuses à

tout moment. Avertir les adultes de maintenir les

enfants et les animaux à distances car le risque de

recevoir des projections d’objet est important.

2. Si quelqu’un appelle ou interrompt le travail d’une

manière ou d’une autre, arrêter le moteur avant de

se tourner vers la personne.

■ ENTRETIEN

1. De manière à conserver la machine en parfait état

de marche, effectuer à intervalles réguliers les

opérations et les vérifications d’entretien décrites

dans le mode d’emploi.

2. Toujours arrêter le moteur avant d’effectuer les

vérifications ou opérations d’entretien.

(1) Tout est en ordre de marche !

Les pièces métalliques atteignent leur plus haute

température aussitôt après l’arrêt de la machine.

3. Lors du remplacement de l’outil de coupe, de pièce

de rechange, de l’huile ou du graissage, veiller à

n’utiliser que des pièces ou des produits

RedMax.

4. Pour toute pièce devant être remplacée, opération

d’entretien ou de réparation, contacter le centre de

SAV agréé par RedMax le plus proche pour

demander assistance.

AVERTISSEMENT

1. Coja los mangos firmemente con ambas manos.

Separe los pies ligeramente (un poco más que el

ancho de sus hombros) de manera que su peso

quede distribuido uniformemente en ambas piernas,

y asegúrese de mantener siempre una postura firme

mientras trabaja.

2. Mantenga el accesorio de corte por debajo del nivel

de su cintura.

3. Mantenga la velocidad del motor al nivel necesario

para realizar el trabajo de corte, y nunca aumente la

velocidad del motor por encima del nivel requerido.

4. Si la unidad comienza a dar sacudidas o a vibrar,

apague el motor y compruebe la unidad completa.

No use la unidad hasta haber corregido

debidamente el problema.

5. Mantenga todas las partes de su cuerpo alejadas

del accesorio de corte que gira y de las superficies

calientes.

6. Nunca toque el silenciador, la bujía u otras piezas

metálicas del motor mientras éste se encuentra en

funcionamiento o inmediatamente después de

apagarlo. De lo contrario, usted podrá sufrir serias

quemaduras o descargas eléctricas.

• SI ALGUIEN SE APROXIMA

1. Evite las situaciones peligrosas en todo momento.

Advierta a los adultos que mantengan a sus niños y

mascotas lejos del área de trabajo. Tenga cuidado

cuando alguien se le acerque. Los desechos que

salen despedidos pueden causar lesiones.

2. Si alguien le llama o le interrumpe de alguna otra

forma mientras trabaja, asegúrese de apagar

siempre el motor antes de voltear.

■ MANTENIMIENTO

1. A fin de mantener el producto en buenas

condiciones de funcionamiento, realice las

operaciones de mantenimiento y comprobación que

se describen en el manual a intervalos regulares.

2. Asegúrese de apagar siempre el motor antes de

realizar cualquier labor de mantenimiento o

comprobación.

(1) Comprobación correcta!

Las partes metálicas alcanzan altas temperaturas y

se mantienen calientes cuando se apaga el motor.

3. Al reemplazar el accesorio de corte o cualquier otra

pieza, o al cambiar el aceite o cualquier lubricante,

asegúrese de usar solamente productos RedMax

o productos que hayan sido certificados por

RedMax para ser usados con esta máquina.

4.En caso de que sea necesario sustituir alguna pieza

o realizar algún trabajo de mantenimiento o

ADVERTENCIA

5. Consignes de securite 5. Instrucciones de seguridad

Français Español

20

manual must be performed, please contact a

representative from the store nearest RedMax

authorized servicing dealer for assistance.

5. Do not use any accessory or attachment other than

those bearing the RedMax mark and recommended

for the unit.

6. Under no circumstances should you ever take apart

the product or alter it in any way. Doing so might

result in the product becoming damaged during

operation or the product becoming unable to operate

properly.

■ HANDLING FUEL

1. The engine of the RedMax product is designed to

run on a mixed fuel which contains highly flammable

gasoline. Never store cans of fuel or refill the tank of

the unit in any place where there is a boiler, stove,

wood fire, electrical sparks, welding sparks, or any

other source of heat or fire which might ignite the

fuel.

2. Never smoke while operating the unit or refilling its

fuel tank.

3. When refilling the tank, always turn off the engine

and allow it to cool down. Take a careful look around

to make sure that there are no sparks or open

flames anywhere nearby before refueling.

(1) Refill after cooling the engine

4. Wipe spilled fuel completely using a dry rag if any

fuel spillage occurs during refueling.

5. After refueling, screw the fuel cap back tightly onto

the fuel tank and then carry the unit to a spot 10feet

(3m) or more away from where it was refueled

before turning on the engine.

■ TRANSPORTATION

1. When hand-carrying the product, cover over the

cutting part if necessary, lift up the product and carry

it paying attention to the blade.

2. Never transport the product over rough roads over

long distances by vehicle without removing all fuel

from the fuel tank. If doing so, fuel might leak from

the tank during transport.

5. For safe operation

English

La page charge ...

RedMax Edger HEZ2602S Manuel utilisateur

Ce manuel convient également à

RedMax Edger HEZ2602S Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents