Maytag MEDX500BW Mode d'emploi

Maytag
Marque
Maytag
Modèle
MEDX500BW
Catégorie
Sèche-linge
Taper
Mode d'emploi

Ce manuel convient également à

W10594781A
W10594782A - SP
ELECTRIC or GAS DRYER
USE AND CARE GUIDE
Table of Contents Table des matières
DRYER SAFETY ............................................................2
CHECK YOUR VENT SYSTEM
FOR GOOD AIR FLOW .................................................4
USE SENSOR DRY CYCLES FOR BETTER
FABRIC CARE AND ENERGY SAVINGS ......................4
CONTROL PANEL & FEATURES .................................. 5
CYCLE GUIDE ............................................................... 6
USING YOUR DRYER ...................................................7
DRYER CARE ................................................................9
TROUBLESHOOTING .................................................11
WARRANTY ................................................................. 13
ASSISTANCE OR SERVICE .................... BACK COVER
SÉCURITÉ DE LA SÉCHEUSE ...................................14
VÉRIFICATION D’UNE CIRCULATION
D’AIR ADÉQUATE POUR LE SYSTÈME
D’ÉVACUATION ..........................................................16
UTILISATION DES PROGRAMMES DE SÉCHAGE
PAR DÉTECTION POUR UN MEILLEUR SOIN
DU TISSU ET DAVANTAGE D’ÉCONOMIES
D’ÉNERGIE .................................................................. 16
TABLEAU DE COMMANDE
ET CARACTÉRISTIQUES ...........................................17
GUIDE DE PROGRAMMES ........................................18
UTILISATION DE LA SÉCHEUSE ...............................19
ENTRETIEN DE LA SÉCHEUSE ................................. 21
DÉPANNAGE. ..............................................................24
GARANTIE. ..................................................................26
ASSISTANCE
OU SERVICE. ........................COUVERTURE ARRIÈRE
SÉCHEUSE
ÉLECTRIQUE ou À GAZ
GUIDE D’UTILISATION
ET D’ENTRETIEN
Para una versión de estas instrucciones en español, visite www.maytag.com
2
DRYER SAFETY
3
4
CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW
Good air ow
Along with heat, dryers require good air ow to efciently
dry laundry. Proper venting will reduce your drying times
and improve your energy savings. See “Installation Instruc-
tions.”
The venting system attached to the dryer plays a big role in
good air ow.
Service calls caused by improper venting are not covered
by the warranty and will be paid by the customer, regardless
of who installed the dryer.
Maintain good air ow by:
Good Better
USE SENSOR DRY CYCLES FOR BETTER FABRIC CARE
AND ENERGY SAVINGS
Use the SENSOR DRY cycles to provide the most energy savings and enhanced fabric care from the dryer. During SENSOR DRY
cycles, drying air temperature or moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the
dryer shuts off when the load reaches the selected dryness. The Energy Preferred cycle will provide optimal energy savings.
With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.
n
Cleaning your lint screen before each load.
n
Replace plastic or foil vent material with 4" (102 mm)
diameter heavy, rigid vent material.
n
Use the shortest length of vent possible.
n
Use no more than four 90° elbows in a vent system;
each bend and curve reduces air ow.
n
Remove lint and debris from the exhaust hood.
n
Remove lint from the entire length of the vent system at
least every 2 years. When cleaning is complete, be sure
to follow the “Installation Instructions” supplied with your
dryer for nal product check.
n
Clear away items from the front of the dryer.
5
CONTROL PANEL & FEATURES
TEMPERATURE
Select a drying temperature based on the fabrics in your
load. If you are unsure of the temperature to select for a
load, select the lower setting rather than the higher setting.
SIGNAL
The Signal produces an audible sound when the drying cycle
is nished. Promptly removing clothes at the end of the cycle
reduces wrinkling.
Turn the SIGNAL knob to select the desired setting (Off,
Low, or High).
CYCLE KNOB
Use Cycle Knob to select available cycles on your dryer.
Turn the knob to select a cycle for your laundry load. See
“Cycle Guide” for detailed descriptions of cycles.
TIMED DRY
Will run the dryer for the specied time on the control.
On models with a selectable temperature knob, you
may choose a setting based on the fabrics in your load.
On some models, temperature is included in the cycle
selections. Drying time and temperature will depend on
your dryer model.
SENSOR DRY
Senses moisture in the load or air temperature and shuts
off when the load reaches the selected dryness level.
Gives the best drying in the shortest time. Drying time
will vary based on fabric type, load size, and temperature
setting.
1
2
5
WRINKLE CONTROL Feature
The WRINKLE CONTROL feature will run after your drying
cycle is complete. It periodically starts and stops the dryer,
tumbling the load without heat to help avoid wrinkling.
WRINKLE CONTROL automatically starts at the end of the
cycle. Opening the door will stop this feature.
n
Get up to 120 minutes of heat-free, periodic tumbling at
the end of a cycle. Turn the WRINKLE CONTROL knob
to OFF, 60 min., or 120 min. at any time before the cycle
has ended.
NOTE: A signal will sound periodically when the WRINKLE
CONTROL setting is selected, but only if the Signal is also
selected.
PUSH TO START
Press the PUSH TO START knob to start the dryer.
Not all features and options are available on all models.
Appearance may vary.
52 3 41
3
4
6
SENSOR DRY - Senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.
Choose ENERGY PREFERRED cycle for optimal energy savings.
Not all cycles and settings are available on all models.
Items to dry:
Temperature:
Available
Options:
Cycle Details:
Signal
Wrinkle Control
CYCLE GUIDE — SENSOR DRY CYCLES
CYCLE GUIDE — TIMED DRY CYCLES
TIMED DRY - Will run the dryer for the specied time on the control.
Not all cycles and settings are available on all models.
NOTE: If loads do not seem as dry as you would like, select More Dry next time you dry a similar load. If loads seem drier than you
like, select Less Dry next time you dry a similar load.
Casual, shirts, pants,
lightweight items,
synthetics, delicates,
athletic wear
Signal
Wrinkle Control
Jeans, heavy work
clothes, towels
More Dry
Energy Preferred
Less Dry
More Dry
Energy Preferred
Less Dry
More Dry
Energy Preferred
Less Dry
Signal
Wrinkle Control
Automatic cycles give the best drying
in the shortest time. Drying time varies
based on fabric type, load size, and
dryness setting.
Select a drying temperature based on
the fabrics in your load. If you are unsure
of the temperature to select for a load,
select the lower setting rather than the
higher setting.
Dryness Level:
High
Medium or
Low
Low
Work clothes, medium
weight fabrics, sheets
Items to dry: Temperature:Cycle:
Available
Options:
Cycle Details:
Setting the Drying Temperature
If your dryer has multiple heat settings:
A High temperature setting may be used for drying
heavyweight items such as towels and work clothes.
A Low to Medium temperature setting may be used for drying
medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use the Air Fluff (no heat) setting for foam, rubber, plastic, or
heat-sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions.
Rubber, plastic, heat
sensitive fabrics
Timed Dry
Air Fluff
Signal
No heat drying.
Any load Freshen Up Any Signal Use low to medium temperature to
smooth out wrinkles, such as those
found in clothes packed in a suitcase or
in items wrinkled from being left in the
dryer too long.
Towels, bedding,
children’s clothing
Sanitize Sanitize Signal Extended high-heat drying cycle
intended to help sanitize items such as
bedding, towels, and baby wear. This
cycle is not recommended for all fabrics.
For best results, run cycle to completion,
do not interrupt.
7
USING YOUR DRYER
1. Clean the lint screen
Clean the lint screen before each load. Pull the lint screen out
of its holder. Roll lint off the screen with your ngers. Do not
rinse or wash screen to remove lint. Push the lint screen rmly
back into place.
For additional cleaning information, see “Dryer Care”.
2. Load the dryer
Place laundry in the dryer. Close the door.
Do not tightly pack the dryer; clothes should be able to tumble
freely.
NOTE: Your model may have a different door than the one
shown. Some models have drop down doors.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this dryer.
Before using your dryer, wipe the dryer drum with a damp cloth
to remove dust from storing and shipping.
3. Select the desired cycle
Select the desired cycle for your load. See the Cycle Guide
for more information about each cycle.
SENSOR DRY Cycles
You can select a different dryness level, depending on your
load, by turning the knob to dryness level.
Selecting More Dry, Energy Preferred, or Less Dry
automatically adjusts the dryness level of the fabrics at which
the dryer will shut off.
SENSOR DRY cycles give the best drying in the shortest time.
Drying time varies based on fabric type, load size, and dryness
setting. Choose Energy Preferred for optimal energy savings.
Less Dry removes less moisture and is used for loads you may
want to put on a hanger to complete drying.
More Dry removes more load moisture. Energy Preferred is
used for a starting point for SENSOR DRY cycles.
8
7. Press PUSH TO START to begin
cycle
Push and hold the PUSH TO START knob to begin the cycle.
4. Set temperature
Select temperature by turning the knob to the desired position
or select the Sensor Dry cycle that has the temperature
included in the cycle selections. Turn the TEMPERATURE knob
to change the drying temperature setting. See “Setting the
Drying Temperature”.
NOTE: Not all options and settings are available with all cycles.
5. Select Signal (if desired)
Turn the SIGNAL knob to select the desired setting (Off, Low,
or High). The Signal produces an audible sound when the
drying cycle is nished. Promptly removing clothes at the end
of the cycle reduces wrinkling.
DRYING RACK
To purchase a drying rack for your dryer, please refer to
“Assistance or Service” on the back cover of the manual or
contact the dealer from whom you purchased your dryer.
Part Number Accessory
3406839 Drying rack - ts 29" Super Capacity Plus
6. Select Wrinkle Control (if desired)
Select Wrinkle Control by turning the knob to the desired
position.
Get up to 120 minutes of heat-free, periodic tumbling at the
end of a cycle. Turn the WRINKLE CONTROL knob to OFF,
60 min., or 120 min. at any time before the cycle has ended.
NOTE: Not all options and settings are available with all
cycles.
9
DRYER CARE
Keep dryer area clear and free from items that would
block the air ow for proper dryer operation. This includes
clearing piles of laundry in front of the dryer.
Cleaning the lint screen
Every load cleaning
The lint screen is located in the dryer. A screen blocked by
lint can increase drying time.
To clean:
1. Pull the lint screen out of its holder. Roll lint off the
screen with your ngers. Do not rinse or wash screen to
remove lint. Wet lint is hard to remove.
2. Push the lint screen rmly back into place.
IMPORTANT:
n
Do not run the dryer with the lint screen loose,
damaged, blocked, or missing. Doing so can cause
overheating and damage to both the dryer and fabrics.
n
If lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See
“Venting Requirements.”
As needed cleaning
Laundry detergent and fabric softener residue can build
up on the lint screen. This buildup can cause longer drying
times for your clothes, or cause the dryer to stop before
your load is completely dry. The screen is probably clogged
if lint falls off while the screen is in the dryer.
Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup.
To wash:
1. Roll lint off the screen with your ngers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent.
Scrub lint screen with the brush to remove residue
buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Reinstall
screen in dryer.
Cleaning the dryer interior
To clean dryer drum
1. Apply a liquid, nonammable household cleaner to the
stained area of the drum and rub with a soft cloth until
stain is removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments that contain loose dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and
will not stain future loads of clothes. Dry these items inside
out to avoid drum staining.
Removing accumulated lint
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often,
depending on dryer usage. Cleaning should be done by a
qualied servicer.
From the Exhaust Vent
Lint should be removed every 2 years, or more often,
depending on dryer usage.
Cleaning the dryer location
10
Vacation, storage, and moving care
Non-Use or Storage Care
Operate your dryer only when you are at home. If you will
be on vacation or not using your dryer for an extended
period of time, you should:
1. Unplug dryer or disconnect power.
2. (For gas dryers only): Close shut-off valve to gas supply
line.
3. Clean lint screen. See “Cleaning the Lint Screen.”
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord.
2. Make sure leveling legs are secure in dryer base.
3. Use tape to secure dryer door.
For direct-wired dryers:
1. Turn off power at fuse or breaker box.
2. Disconnect wiring.
3. Make sure leveling legs are secure in dryer base.
4. Use tape to secure dryer door.
For gas dryers:
1. Unplug or disconnect power to dryer.
2. Close shut-off valve in gas supply line.
3. Disconnect gas supply line pipe and remove ttings
attached to dryer pipe.
4. Cap the open fuel supply line.
5. Make sure leveling legs are secure in dryer base.
6. Use tape to secure dryer door.
Reinstalling the Dryer
Follow the “Installation Instructions” to locate, level, and
connect the dryer.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Changing the drum light
(on some models)
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on the
back wall of the dryer. Using a Phillips-head screwdriver,
remove the screw located in the lower right-hand corner
of the cover. Remove the cover.
3. Turn bulb counterclockwise. Replace the bulb with
a 10-watt appliance bulb only. Replace the cover and
secure with the screw.
4. Plug into a grounded outlet or reconnect power.
11
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience
Possible Causes
Solution
TROUBLESHOOTING
Door not closed completely. Make sure the dryer door is closed completely.
Household fuse is blown or circuit
breaker has tripped.
Electric dryers use 2 household fuses or circuit breakers. The
drum may be turning, but you may not have heat. Replace both
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
Dryer will not run
PUSH to START knob not pressed
rmly or held long enough.
Incorrect power supply.
Electric dryers require 240-volt power supply. Check with a
qualied electrician.
Wrong type of fuse.
Use a time-delay fuse.
Unusual sounds
Dryer had a period of non-use.
If the dryer hasn’t been used for awhile, there may be a
thumping sound during the rst few minutes of operation.
Check the front and rear edges of the drum for small objects.
Clean out pockets before laundering.
The four legs are not installed, or the
dryer is not level front to back and
side to side.
The dryer may vibrate if not properly installed.
See “Installation Instructions”.
A coin, button, or paper clip is
caught between the drum and front
or rear of the dryer.
Clothing knotted or balled up.
When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.
Press and hold the PUSH to START knob until you hear the dryer
drum moving.
No heat Household fuse is blown or circuit
breaker has tripped.
The drum may be turning, but you may not have heat. Electric
dryers use 2 household fuses or circuit breakers. Replace both
fuses or reset the circuit breaker. If the problem continues, call
an electrician.
It is a gas dryer.
The gas valve clicking is a normal operating sound.
Supply line valve not open. For gas dryers, make sure the supply line valve is open.
Clothes are not drying
satisfactorily, drying
times are too long
Lint screen clogged with lint.
Lint screen should be cleaned before each load.
The Air Fluff cycle has been
selected.
Select the right cycle for the types of garments being dried.
See “Cycle Guide.”
Load too large and heavy to dry
quickly.
Separate the load to tumble freely.
Exhaust vent or outside exhaust
hood clogged with lint, restricting
air movement.
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel
air movement, clean exhaust system of lint or replace exhaust
vent with heavy metal or exible metal vent. Make sure vent is
not crushed or kinked. See “Installation Instructions”.
Exhaust vent diameter not the
correct size.
Use 4" (102mm) diameter vent material.
Dryer located in a room with
temperature below 45ºF (7ºC).
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
Dryer located in a closet without
adequate opening.
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (25mm) of airspace, and, for most installations, the rear of
the dryer requires 5" (127mm). See “Installation Instructions”.
Exhaust vent not the correct length.
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. Make sure vent is
not crushed or kinked. See “Installation Instructions”.
Fabric softener sheets blocking
the grille.
Use only one fabric softener sheet, and use it only once.
Incorrect power supply.
Electric dryers require 240-volt power supply. Check with a
qualied electrician.
12
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience
Possible Causes
Solution
TROUBLESHOOTING cont.
Cycle time too short
Sensor Dry cycle ending early. The load may not be contacting the sensor strips. Level the
dryer.
Use Timed Dry for very small loads. Change the Dry Level
setting on SENSOR DRY cycles.
Increasing or decreasing the Dry Level setting will change the
amount of drying time in a cycle.
Lint on load
Lint screen clogged.
Lint screen should be cleaned before each load.
Stains on load or drum
Dryer fabric softener not properly
used.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can stain
your garments.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
Loads are wrinkled
Load not removed from dryer at the
end of the cycle.
Use a cycle with Wrinkle Control to tumble the load without
heat to avoid wrinkling.
Dryer tightly packed.
Dry smaller loads that can tumble freely and reduce formation
of wrinkles.
Odors
You have recently been painting,
staining, or varnishing in the area
where your dryer is located.
If so, ventilate the area. When the odors or fumes are gone
from the area, rewash and dry the clothing.
The electric dryer is being used for
the rst time.
The new electric heating element may have an odor. The odor
will be gone after the rst cycle.
Load is too hot
Laundry items were removed from
the dryer before the end of the
cycle.
Allow Cool Down cycle to nish before removing laundry from
dryer. All cycles are cooled slowly to reduce wrinkling and make
it easier to handle. Items removed before Cool Down may feel
very warm.
A high temperature cycle was used
or Temperature control was set to
high.
Select a lower temperature, and use an sensor drying cycle.
These cycles sense the temperature or the moisture level in the
load and shut off when the load reaches the selected dryness.
This reduces overdrying.
13
MAYTAG
®
LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions
attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Maytag”) will
pay for factory specied replacement parts and repair labor to correct defects in materials or workmanship that existed when this
major appliance was purchased.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Service must be provided by a Maytag designated service company. This limited warranty is valid only in the United States or Canada
and applies only when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the
date of original consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when
it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace
or repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air lters, or water lters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, re, ood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Maytag.
5. Cosmetic damage, including scratches, dents, chips or other damage to the nish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by
an authorized Maytag servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Maytag published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered,
or cannot be easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and
provinces do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply
to you. This warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to
province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty
gives
you specic legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
If you think you need repair service, rst see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve
the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by
calling Maytag. In the U.S.A., call 1 -800 -688- 9900. In Canada, call 1 -800- 807 -6777. 10/11
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need
it. You will need to know your complete model number and serial
number. You can nd this information on the model and serial
number label located on the product.
Dealer name _____________________________________________
Address __________________________________________________
Phone number ____________________________________________
Model number ____________________________________________
Serial number ____________________________________________
Purchase date ____________________________________________
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.
14
SÉCURITÉ DE LA SÉCHEUSE
15
16
VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE POUR
LE SYSTÈME D’ÉVACUATION
Maintenir une bonne circulation d’air
en effectuant les opérations suivantes :
n
Nettoyer le ltre à charpie avant chaque charge.
n
Remplacer le matériau de conduits d’évacuation en
plastique ou en aluminium par des conduits d’évacuation
lourds et rigides de 4" (102 mm) de diamètre.
n
Toujours employer les conduits d’évacuation les plus
courts possible.
n
Ne pas utiliser plus de quatre coudes à 90° dans un
circuit d’évacuation car chaque inclinaison et courbe
réduit le ux d’air.
n
Retirer la charpie et les résidus du clapet d’évacuation.
n
Retirer la charpie sur toute la longueur du circuit
d’évacuation au moins tous les 2 ans. Après le
nettoyage, veuillez suivre les instructions d’installation
fournies avec la sécheuse pour une vérication nale
de l’appareil.
n
Dégager tout article qui se trouverait devant la sécheuse.
Circulation d’air adéquate
Une sécheuse a besoin de chaleur et d’une circulation
d’air adéquate pour sécher efcacement le linge. Une
ventilation adéquate réduit les durées de séchage et accroît
les économies d’énergie. Voir les Instructions d’installation.
Le système d’évacuation xé à la sécheuse joue un rôle
important dans la circulation de l’air.
Les interventions de dépannage causées par une ventilation
incorrecte ne sont pas couvertes par la garantie et seront
à la charge du client, quel que soit l’installateur de la
sécheuse.
UTILISATION DES PROGRAMMES DE SÉCHAGE
PAR DÉTECTION POUR UN MEILLEUR SOIN DU
TISSU ET DAVANTAGE D’ÉCONOMIES D’ÉNERGIE
Utiliser les programmes de séchage par détection permet à la sécheuse de réaliser davantage d’économies d’énergie et
d’apporter un soin supérieur aux tissus. Durant les programmes de séchage automatique/de séchage par détection, la
température de séchage de l’air et le niveau d’humidité sont détectés dans la charge. Cette détection se produit tout au long
du programme de séchage et la sécheuse s’éteint lorsque la charge atteint le degré de séchage sélectionné. Le programme
Energy Preferred (éconergique) entraînera des économies d’énergie optimales.
Avec l’option de séchage minuté, la sécheuse fonctionne pendant la durée réglée, ce qui peut parfois entraîner le
rétrécissement ou le froissement du linge, et l’accumulation d’électricité statique due au séchage excessif. Utiliser le séchage
minuté pour une charge encore humide nécessitant un peu de temps supplémentaire ou lorsqu’on utilise la grille de séchage.
Bon
Mieux
17
TABLEAU DE COMMANDE ET CARACTÉRISTIQUES
TEMPERATURE (température)
Choisir une température de séchage en fonction des
tissus de votre charge. Si vous hésitez sur la température
à sélectionner pour une charge donnée, choisir le réglage
plus bas plutôt que le réglage plus élevé.
SIGNAL (signal)
Le signal de n de programme émet un signal sonore qui
indique la n du programme de séchage. Le fait de sortir
rapidement les vêtements à la n du programme permet
de réduire le froissement.
Tourner le bouton SIGNAL (signal) pour sélectionner le
réglage désiré (Off [arrêt], Low [bas] ou High [élevé]).
BOUTON DE PROGRAMME
Utiliser le bouton de programme pour sélectionner les
programmes disponibles sur la sécheuse. Tourner le
bouton de programme pour sélectionner un programme
correspondant à la charge de linge. Voir “Guide de
programmes” pour des descriptions de programmes
détaillées.
TIMED DRY (séchage minuté)
Ceci fait fonctionner la sécheuse pour la durée spéciée
sur le module de commande. Pour les modèles dotés
d’un bouton de sélection de température, vous pouvez
choisir un réglage en fonction des tissus de votre
charge. Sur certains modèles, la température est
incluse dans les sélections de programmes. Le temps
de séchage et la température dépendront du modèle de
votre sécheuse.
SENSOR DRY (séchage par détection)
Détecte l’humidité de la charge et la température de l’air
et s’éteint lorsque la charge a atteint le degré de
séchage sélectionné. Permet d’obtenir le meilleur
rendement de séchage en un minimum de temps. Le
temps de séchage variera en fonction du type de tissu,
du volume de la charge et du réglage de température.
1
4
5
Caractéristique WRINKLE CONTROL
(antifroissement)
La caractéristique antifroissement démarre après la
n du programme de séchage. Elle met la sécheuse
en marche et l’arrête périodiquement tout en faisant
culbuter la charge sans chaleur pour éviter le
froissement.
Caractéristique antifroissement démarre automatiquement
à la n du programme. L’ouverture de la porte arrête cette
caractéristique.
n
Obtenir jusqu’à 120 minutes de culbutage périodique
sans chaleur à la n d’un programme. Tourner le bouton
WRINKLE CONTROL (antifroissement) à OFF (arrêt),
60 min. ou 120 min. à tout moment avant la n d’un
programme.
REMARQUE : Lorsque la caractéristique antifroissement
est sélectionnée, un signal sonore retentit régulièrement,
mais seulement si le signal de n de programme est
également sélectionné.
PUSH TO START
(enfoncer pour mettre en marche)
Appuyer sur le bouton PUSH TO START (enfoncer pour
mettre en marche) pour mettre la sécheuse en marche.
Certains programmes et options ne sont pas disponibles sur certains modèles.
L’apparence des appareils peut varier.
52 3 41
2
3
18
SÉCHAGE PAR DÉTECTION - Détecte l’humidité présente dans la charge ou la température de l’air et s’éteint lorsque la charge
atteint le degré de séchage sélectionné. Sélectionner le programme ENERGY PREFERRED (éconergique) pour des économies
d’énergie optimales.
Certains programmes ne sont pas disponibles sur certains modèles.
Articles à sécher :
Température
tissu :
Options
disponibles :
Détails du programme :
Cycle Signal
(signal de fin de
programme)
Wrinkle Control
(antifroissement)
GUIDE DE PROGRAMMES — PROGRAMMES DE SÉCHAGE
PAR DÉTECTION
GUIDE DE PROGRAMMES — SÉCHAGE MINUTÉ
TIMED DRY (séchage minuté) - Fait fonctionner la sécheuse pour la durée spéciée sur le module de commande.
Certains programmes ne sont pas disponibles sur certains modèles.
REMARQUE : Si les charges ne semblent pas aussi sèches que désiré, sélectionner More Dry (plus sec) la prochaine fois que l’on
sèche une charge semblable. Si les charges semblent plus sèches que désiré, sélectionner Less Dry (moins sec) la prochaine fois que
l’on sèche une charge semblable.
Tout-aller, chemisiers,
pantalons, articles légers,
synthétiques, tissus
délicats, vêtements de
sport
Cycle Signal
(signal de fin de
programme)
Wrinkle Control
(antifroissement)
Jeans, vêtements de travail
lourds, serviettes
More Dry
(plus sec)
Energy Preferred
(éconergique)
Less Dry
(moins sec)
More Dry
(plus sec)
Energy Preferred
(éconergique)
Less Dry
(moins sec)
More Dry
(plus sec)
Energy Preferred
(éconergique)
Less Dry
(moins sec)
Cycle Signal
(signal de fin de
programme)
Wrinkle Control
(antifroissement)
Les programmes automatiques permettent
d’obtenir le meilleur rendement de séchage en
un minimum de temps. Le temps de séchage
variera en fonction du type de tissu, du volume
de la charge et du réglage de séchage.
Choisir une température de séchage en
fonction des tissus de votre charge. Si vous
hésitez sur la température à sélectionner pour
une charge donnée, choisir le réglage le plus
bas plutôt que le réglage le plus élevé.
Niveau de
séchage :
High
(élevée)
Medium
(moyenne)
ou
Low
(basse)
Low
(faible)
Vêtements de travail,
articles moyennement
lourds, draps
Articles à sécher : Température :Programme :
Options disponibles : Détails du programme :
Caoutchouc, plastique,
tissus sensibles à la
chaleur
Timed Dry
(séchage minuté)
Air Fluff
(duvetage à l’air)
Signal
(signal)
Séchage sans chaleur.
N’importe quelle
charge
Freshen Up
(rafraîchissement)
N’importe laquelle Signal
(signal)
Aide à aplanir les faux plis grâce à une
température basse à moyenne, pour des
articles tels que les vêtements qui ont
séjourné dans une valise ou qui sont
restés trop longtemps dans la sécheuse.
Sanitize
(assainissement)
Sanitize
(assainissement)
Signal
(signal)
Serviettes, literie,
vêtements d’enfants
Programme de séchage à chaleur élevée
prolongé conçu pour aider à assainir
les articles tels que literie, serviettes et
vêtements pour bébé. Ce programme n’est
pas recommandé pour tous les tissus. Pour
de meilleurs résultats, faire fonctionner
le programme jusqu’à la n et ne pas
l’interrompre.
19
Réglage de la température de séchage
Si la sécheuse comporte plusieurs réglages de chaleur :
On peut utiliser un réglage High (chaleur élevée) pour sécher
les articles lourds tels que les serviettes et les vêtements de
travail.
Un réglage de chaleur Low Delicate (délicat) à Medium
Casual (tout-aller) peut être utilisé pour sécher les articles
moyennement lourds tels que draps, chemisiers, robes,
sous-vêtements, tissus à pressage permanent et certains
tricots.
Utiliser le réglage Air Fluff (duvetage à l’air [sans chaleur]) pour
la mousse, le caoutchouc, le plastique ou les tissus sensibles à
la chaleur.
Sécher sur une corde à linge les tissus doublés ou
multicouches.
REMARQUE : Pour toute question concernant les
températures de séchage pour diverses charges, consulter les
instructions sur l’étiquette de soin.
UTILISATION DE LA SÉCHEUSE
1. Nettoyer le ltre à charpie
Nettoyer le ltre à charpie avant chaque charge. Tirer le ltre à
charpie de son support. Enlever la charpie du ltre en la roulant
avec les doigts. Ne pas rincer ni laver le ltre pour enlever la
charpie. Remettre le ltre à charpie fermement en place.
Pour plus d’informations sur le nettoyage, voir “Entretien de la
sécheuse”.
2. Charger la sécheuse
Placer le linge dans la sécheuse. Fermer la porte.
Ne pas surcharger la sécheuse; les vêtements doivent pouvoir
culbuter librement.
REMARQUE : La porte de votre modèle peut différer de celle
gurant sur l’illustration. Certains modèles peuvent comporter
des portes à ouverture vers le bas.
AVERTISSEMENT : Pour réduire le risque d’incendie, de choc
électrique ou de blessures à autrui, lire les IMPORTANTES
INSTRUCTIONS DE SÉCURITÉ avant de faire fonctionner cette
sécheuse.
Avant d’utiliser la sécheuse, essuyer le tambour de la sécheuse
avec un linge humide pour enlever la poussière accumulée au
cours de l’entreposage et de l’expédition.
20
4. Régler la température
Sélectionner la température en tournant le bouton à la
position désirée ou sélectionner le programme de séchage par
détection dont la température gure dans les sélections de
programme. Tourner le bouton TEMPERATURE (température)
pour modier le réglage de la température de séchage. Voir
“Réglage de la température de séchage”.
REMARQUE : Tous les réglages et options ne sont pas
disponibles avec tous les programmes.
3. Sélectionner le programme désiré
Sélectionner le programme souhaité pour la charge. Voir le
Guide de programmes pour plus d’informations sur chaque
programme.
PROGRAMMES DE SÉCHAGE PAR DÉTECTION
Selon votre charge, vous pouvez sélectionner un degré de
séchage différent en tournant le bouton sur le degré de
séchage.
Lorsqu’on sélectionne More Dry (plus sec), Energy Preferred
(éconergique) ou Less Dry (moins sec), le degré de séchage
qui commandera l’arrêt de la sécheuse est automatiquement
ajusté.
Les programmes de séchage par détection offrent un séchage
idéal en un minimum de temps. La durée de séchage varie en
fonction du type de tissu, de la taille de la charge et du réglage
de niveau de séchage. Sélectionner le programme Energy
Preferred (éconergique) pour réaliser des économies d’énergie
optimales. Le séchage Less Dry (moins sec) élimine moins
d’humidité et est utilisé pour les charges que l’on souhaite
placer sur un cintre pour qu’elles nissent de sécher.
Le séchage More Dry (plus sec) élimine davantage d’humidité
dans la charge. Energy Preferred (éconergique) est utilisé
comme point de départ dans les programmes DE SÉCHAGE
PAR DÉTECTION.
5. Sélectionner le signal de n
de programme (si désiré)
Tourner le bouton SIGNAL (signal) pour sélectionner le
réglage désiré (Off [arrêt], Low [bas] ou High [élevé]). Le signal
de n de programme est un signal sonore qui retentit lorsque
le programme de séchage est terminé. Sortir rapidement les
vêtements à la n du programme réduit le froissement.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Maytag MEDX500BW Mode d'emploi

Maytag
Marque
Maytag
Modèle
MEDX500BW
Catégorie
Sèche-linge
Taper
Mode d'emploi
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents