GE Profile PSS26NSWSS Manuel utilisateur

ge.com
Refrigerators
Profile Side by Side
200D8074P017 49-60494-2   07-08 JR
La section française commence à la page 46
La sección en español empieza en la página 88
Safety Instructions . . . . . . . . . . . .2–4
Operating Instructions
Automatic Icemaker  . . . . . . . . . . . .14
Care and Cleaning  . . . . . . . . . .16, 17
ClimateKeeper2
™
 . . . . . . . . . . . . . . .6
Crispers and Pans  . . . . . . . . . . . . . .13
CustomCool
™
 . . . . . . . . . . . . . . . .7, 8
Ice and Water Dispenser  . . . . .15–16
QuickFreeze
™
 . . . . . . . . . . . . . . . . . .9
Quick Ice  . . . . . . . . . . . . . . . . . . . . .15
Refrigerator Doors  . . . . . . . . . . . . .12
Replacing the Light Bulbs  . . . . . . .18
Shelves and Bins  . . . . . . . . . . . .10, 11
Temperature Controls  . . . . . . . . . . .5
TurboCool
™
 . . . . . . . . . . . . . . . . . . . .6
Water Filter  . . . . . . . . . . . . . . . . . . . .9
Installation Instructions
Installing the Refrigerator  . . . .28–31
Moving the Refrigerator . . . . . .24–27
Preparing to Install 
the Refrigerator  . . . . . . . . . . . . . . .23
Trim Kits and Panels . . . . . . . . .19–22
Water Line Installation . . . . . . .32–34
Troubleshooting Tips  . . . . . . .36–38
Normal Operating Sounds . . . . . . .35
Consumer Support
Consumer Support  . . . . .Back Cover
Performance Data Sheet  . . . . . . . .41
Product Registration . . . . . . . . .43, 44
Warranty (Canadian)  . . . . . . . . . . .39
Warranty (U.S.) . . . . . . . . . . . . . . . .40
Réfrigérateurs
Profile Côte à Côte
Refrigeradores
Profile Lado a Lado
Models 23, 25 and 26
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label inside 
the refrigerator compartment at the 
top on the right side.
Owner’s Manual 
and Installation
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet. Skin

may stick to these extremely cold surfaces.

■

■Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

located on the bottom of the icemaker. Do not

place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

Non-LCD models:

Setting either or both controls to

0 (off)

does not remove power to the light circuit.

■

LCD models:

Turning the cooling system off does

not remove power to the light circuit.

■

■Do not refreeze frozen foods which have

thawed completely.

■

■Always clean the

CustomCool

™

Tray after thawing

food.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

ge.com

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous…even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

■Take off the doors.

■Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the

company handling the disposal about what

to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use

of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

3

4

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

If the outlet is a standard 2-prong outlet, it is your

personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall

outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull straight

out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

About the temperature controls. ge.com

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not

removed during installation, remove it now.

The temperature controls are preset in the factory at 37°F (3°C) for the

refrigerator compartment and 0°F (-18°C) for the freezer compartment.

Allow 24 hours for the temperature to stabilize to the preset

recommended settings.

Refrigerator temperatures can be adjusted between 34°F and 44°F

(1°C to 7°C), and the freezer temperatures can be adjusted between

–6°F and +6°F (–21°C to –14°C).

To change the Refrigerator temperature:

LCD Models:

Access By:

Home > Refrigerator

Activate By:

Using the arrows to select the desired

temperature. You must press

ENTER

to set the new

temperature.

To change the Freezer temperature:

Access By:

Home > Freezer

Activate By:

Using the arrows to select the desired

temperature. You must press

ENTER

to set the new

temperature.

Once the desired temperature has been set, the display will

return to the

HOME

screen and show the set temperatures

underneath the actual temperature display for several

seconds. Several adjustments may be required. Each time

you adjust the controls, allow 24 hours for the refrigerator

to reach the temperature you have set.

Non-LCD Models:

To change the temperature, press and release the

WARMER

or

COLDER

pad. The

SET

light will come on and the display

will show the set temperature. To change the temperature,

tap either the

WARMER

or

COLDER

pad until the desired

temperature is displayed.

Once the desired temperature has been set, the

temperature display will return to the actual refrigerator

and freezer temperatures after 5 seconds. Several

adjustments may be required. Each time you adjust the

controls, allow 24 hours for the refrigerator to reach the

temperature you have set.

The temperature controls can display both the SET temperature as well

as the actual temperature in the refrigerator and freezer. The actual

temperature may vary slightly from the SET temperature based on

usage and operating environment.

Turning the cooling system off:

LCD models: Turning the cooling system OFF stops cooling in both the

freezer and refrigerator compartments, but does not shut off electrical

power to the refrigerator.

Non-LCD models: Setting either or both controls to OFF stops cooling in

both the freezer and refrigerator compartments, but does not shut off

electrical power to the refrigerator.

LCD Models:

Access By:

Home > Options > Information and Settings >

Cooling System Off

To turn the cooling system back on, press the touch screen

and press the

ON

button.

Activate By:

Pressing

ENTER.

Non-LCD Models:

Tap the

WARMER

pad for either the refrigerator or the

freezer until the display shows

OFF

.

To turn the unit back on,

press the

COLDER

pad for either the refrigerator or freezer.

The

SET

light will illuminate on the side you selected. Then

press the

COLDER

pad again (on the side where the

SET

light is illuminated) and it will go to the preset points of 0°F

(–18°C) for the freezer and 37°F (3°C) for the refrigerator.

When the unit is turned back on, it will take up to 24 hours

to stabilize.

The Performance Air-Flow System is designed to maximize

temperature control in the refrigerator and freezer

compartments. This unique special feature consists of the

Air Tower along the back wall of the refrigerator and the

Air Tunnel on the bottom portion of the freezer rear wall.

Placing food in front of the louvers on these components

will not affect performance. Although the Air Tower and

the Air Tunnel can be removed, doing so will affect

temperature performance. (For removal instructions,

on-line, 24 hours a day, contact us at ge.com or call

800.GE.CARES. In Canada, contact us at geappliances.ca

or call 1.800.361.3400.)

Performance Air Flow System

5

LCD models

Non-LCD models

On LCD

models

Not all features are on all models. Your controls will look like one of the following:

6

About TurboCool.

™

How it Works

TurboCool

™

rapidly cools the refrigerator

compartment in order to more quickly

cool foods. Use

TurboCool

when adding a

large amount of food to the refrigerator

compartment, putting away foods after they

have been sitting out at room temperature

or when putting away warm leftovers. It can

also be used if the refrigerator has been

without power for an extended period.

Once activated, the compressor will turn on

immediately and the fans will cycle on and

off at high speed as needed for eight hours.

The compressor will continue to run until

the refrigerator compartment cools to

approximately 34°F (1°C), then it will cycle

on and off to maintain this setting. After

8 hours, or if

TurboCool

is pressed again,

the refrigerator compartment will return

to the original setting.

How to Use

LCD Models:

Access By:

Home > Options > Refrigerator

Options > TurboCool

Activate By:

Pressing

ON

.

Deactivate By:

Pressing

OFF

.

Non-LCD Models:

Press

TurboCool

. The refrigerator

temperature display will show

TC

.

After

TurboCool

is complete, the refrigerator

compartment will return to the original

setting.

NOTES:

The refrigerator temperature cannot be changed

during TurboCool.

The freezer temperature is not affected during

TurboCool.

When opening the refrigerator door during

TurboCool, the fans will continue to run if they have

cycled on.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

About ClimateKeeper2.

™

How it Works

The

ClimateKeeper2

™

is the industry’s most

advanced refrigeration system, delivering

optimum temperature and humidity

performance to keep food garden fresh

longer and reduce freezer burn, while

maintaining E star-level efficiency.

The

ClimateKeeper2

system features

two evaporators—one for the refrigerator

and one for the freezer.

This provides two separate cooling systems,

and separates the airflow between the fresh

food and freezer compartments during

normal cooling operations.*

This ensures that the humidity levels in the

fresh food compartment are significantly

higher than in a conventional system,**

allowing fresh produce and other unsealed

foods to retain their moisture content and

freshness longer. Moisture sensitive foods

such as fresh fruit, salads, rice, etc., can now

be stored on open shelves without excessive

moisture loss. Due to the higher humidity

in the refrigerator, you may on occasion

experience fog or small amounts of

moisture in the refrigerator compartment.

This is normal and may come and go as

different food loads and environmental

conditions change. Wipe dry with a paper

towel if desired.

The separate airflow system minimizes

the mixing of air between the two

compartments, which reduces fresh food

odor transfer to improve the taste of ice.

The

ClimateKeeper2

system also reduces

the number of defrosting cycles in the

freezer evaporator, thereby reducing

freezer burn.

*Freezer air is used in the CustomCool feature.

**Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2

refrigerators versus conventional units.

7

Empty the pan. Place the Chill/Thaw

tray in the pan. Place the items on the

tray and close the pan completely.

LCD Models:

Access by:

Home > Options >

Refrigerator Options >

CustomCool

Pan

Non-LCD Models:

Select the

ExpressThaw

™

,

ExpressChill

™

or

SelectTemp

™

pad. The display and

SET

light will come on. Tap the pad

until the light appears next to the

desired setting.

Use the following chart to determine

the best setting to use.

■ On some models,

ExpressChill

has

only one 45 minute setting.

■ To stop a feature before it is finished:

For LCD Models:

Go into that feature’s menu and press

the

OFF

button.

For Non-LCD Models:

Tap that feature’s pad until no

options are selected and the display

is off.

■ During

ExpressThaw

and

ExpressChill

, the display on the

controls will count down the time

in the cycle (on some models).

■ After the

ExpressThaw

cycle is

complete, the pan will reset to the

MEAT

setting (32°F [0°C]) to help

preserve thawed items until they are

used.

■ The displayed actual temperature of

the

CustomCool

pan may vary slightly

from the

SET

temperature based on

usage and operating environment.

NOTE: For food safety reasons, it is recommended

that foods be wrapped in plastic wrap when using

ExpressThaw. This will help contain meat juices

and improve thawing performance.

About CustomCool

™

. (on some models) ge.com

The

CustomCool

™

feature is used to quickly

chill items, thaw items or hold the pan at a

specific temperature. This feature is a

system of dampers, a fan, a temperature

thermistor and a heater.

The pan is tightly sealed to prevent

temperature fluctuations in the rest of the

refrigerator. The controls for this pan are

located at the top of the refrigerator with

the temperature controls, or on the

dispenser with the temperature controls.

How to Use

How it Works

ExpressThaw

™

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are in the

unlock position.

Place the sides of the drawer into the

drawer supports, making sure the swing

locks fit on the drawer slots.

Lock all four swing locks by rotating

them to the lock position.

How to Remove and Replace the Drawer

ExpressChill

™

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

On LCD

models

8

About CustomCool

™

. (on some models)

CustomCool

™

Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

0.5 Lb. (4 hours)

■ Hamburger Patties (0.5 lb)

■ Individually Wrapped

Filet Mignon (0.5 lb)

1.0 Lb. (6 hours)

■ Chicken Breasts (1.0 lb)

■ Ground Beef (1.0 lb)

■ Steak (1.0 lb)

2.0 Lbs. (10 hours)

■ Chicken Breasts (2.0 lbs)

■ Ground Beef (2.0 lbs)

■ Steak (2.0 lbs)

3.0 Lbs. (12 hours)

■ Chicken Breasts (3.0 lbs)

■ Ground Beef (3.0 lbs)

■ Steak (3.0 lbs)

15 Minutes

■ 1 Beverage Can (12 oz)

■ 2 Small Juice Boxes (6–8 oz each)

30 Minutes

■ 2 to 6 Beverage Cans (12 oz each)

■ 2 Plastic 20 oz Bottles of Beverage

■ 4 to 6 Small Juice Boxes

(6–8 oz each)

■ 3 Foil Juice Packets

■ Wine (750 ml bottle)

45 Minutes

■ 2 Liter of Beverage

■ 1/2 Gallon of Juice

■ Gelatin–1 package

Citrus Setting (43°F [6°C])

■ Oranges, Lemons, Limes,

Pineapple, Cantaloupe

■ Beans, Cucumbers, Tomatoes,

Peppers, Eggplant, Squash

Produce Setting (35

°F [2°C])

■ Strawberries, Raspberries, Kiwifruit,

Pears, Cherries, Blackberries,

Grapes, Plums, Nectarines, Apples

■ Asparagus, Broccoli, Corn,

Mushrooms, Spinach, Cauliflower,

Kale, Green Onion, Beets, Onions

Meat Setting (32°F [0°C])

■ Raw Meat, Fish and Poultry

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Some

CustomCool

models feature a beverage

center. It is designed to store beverages at

colder temperatures. Select this feature if

you like to keep extra-chilled refreshments

on hand.

LCD Models:

Access by:

Home > Options > Refrigerator

Options > Beverage Center

Activate by:

Pressing

ON

.

Deactivate by:

Pressing

OFF

.

Non-LCD Models:

Select the

Beverage Center

pad. The set

light will come on and the feature will

operate as required.

To turn off the feature, press

Beverage

Center

pad and set light will turn off.

NOTE: Unless turned off as above, feature will

remain active for six months. Press the Beverage

Center pad to restart.

How to Use the Beverage Center

To remove:

Remove dairy bin first. Holding the

bottom of the dairy bin, lift the front

straight up, then lift up and out.

Holding left and right side of beverage

center, lift straight up and out.

Leave adapter in place.

To replace:

Engage backside of beverage center in

molded supports on adapter. Then

push down on the sides of the beverage

center. The beverage center will lock

into place.

Replace dairy bin.

How to Remove and Replace the Beverage Center

Dairy Bin

Adapter

Beverage

Center

About QuickFreeze.

™

(on some models) ge.com

The

QuickFreeze

plate is only to be

used with the

QuickFreeze

feature.

Use

QuickFreeze

to freeze items faster

to enhance food preservation.

How to Use

Place food (wrapped in plastic wrap) on

QuickFreeze

plate. Turn the feature on via

the LCD controls.

LCD Models:

Access By:

Home > Options > Freezer

Options > QuickFreeze

Activate By:

Using the arrows to select the

time and pressing

Enter

.

Deactivate By:

Pressing

OFF

.

NOTE:

While the

QuickFreeze

feature is

enabled, the actual freezer temperature may

drop as low as –3°F (–19°C). This is normal.

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

About the water filter.

Water Filter Cartridge

The water filter cartridge is located in the

back upper right corner of the refrigerator

compartment.

When to Replace the Filter

LCD Models:

A pop-up screen will appear on the LCD screen

to remind you to replace the water filter. You can

check the status of the water filter manually.

Access By:

Home > Options > Dispenser Options

> Reset Water Filter

Non-LCD Models:

There is a replacement indicator light for the

water filter cartridge on the dispenser. This light

will turn orange to tell you that you need to

replace the filter soon.

The filter cartridge should be replaced when the

replacement indicator light turns red or if the

flow of water to the dispenser or icemaker

decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove

the old one by slowly turning it to the left.

Do not

pull down on the cartridge. A small amount of

water may drip down.

Installing the Filter Cartridge

There is an adapter attached to the top of

the new filter cartridge.

The adapter must be removed before

installing the cartridge. To remove the

adapter, turn it to the left about 1/4 turn.

Fill the replacement cartridge with water

from the tap to allow for better flow from

the dispenser immediately after installation.

Line up the arrow on the cartridge and the

cartridge holder. Place the top of the new

cartridge up inside the holder.

Do not

push

it up into the holder.

Slowly turn it to the right until the filter

cartridge stops.

DO NOT OVERTIGHTEN.

As

you turn the cartridge, it will automatically

raise itself into position. The cartridge will

rotate about 1/2 turn.

Run water from the dispenser for 5 minutes

to clear the system and prevent sputtering.

LCD Models:

Press

FILTER REPLACED

button

to confirm replacement.

Non-LCD Models:

Press and hold the

RESET FILTER

pad

(on some models) on the dispenser for

3 seconds.

NOTE: A newly installed water filter cartridge may cause

water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a

replacement filter cartridge is not available.

The dispenser and the icemaker will not operate

without the filter or filter bypass plug.

Replacement Filters:

To order additional filter cartridges in the United

States, visit our Website, ge.com, or call GE Parts

and Accessories, 800.626.2002.

MSWF

Suggested Retail $36.95–$41.95 USD

Customers in Canada should consult

the yellow pages for the nearest Mabe Service

Center.

Place the top of the cartridge up

inside the cartridge holder and

slowly turn it to the right.

QuickFreeze

Plate

Filter

Bypass

Plug

SmartWater

Cartridge

Holder

9

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

10

About the shelves and bins.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Bins

The larger refrigerator door bins and

freezer tilt-out door bins are adjustable.

To remove:

Lift the front of the bin straight

up, then lift up and out.

To replace or relocate:

Engage the back side

of the bin in the molded supports on the

door. Then push down on the front of the

bin. Bin will lock in place.

The snugger

helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Place a finger on either side of the

snugger near the rear and move it back

and forth to fit your needs.

Top Freezer Bins

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

QuickSpace

™

Shelf

This shelf splits in half and slides under

itself for storage of tall items on the shelf

below.

This shelf can be removed and replaced

or relocated just like Slide-Out Spillproof

Shelves.

On some models, this shelf cannot be used

in the lowest position.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the

shelf straight out.

To replace or relocate:

Line the shelf up with the supports and

slide it into place. The shelf can be

repositioned when the door is at 90° or

more. To reposition the shelf, slide the shelf

past the stops and angle downward. Slide

shelf down to the desired position, line up

with the supports and slide into place.

Make sure you push the shelves all the way back

in before you close the door.

Press tab and pull shelf forward

to remove

Top freezer bin

Do not block

CAUTION:

Be careful when

placing items in the

top bin. Make sure

that items do not

block or fall into

the ice chute.

Top freezer bin (on some models)

Do not block

CAUTION:

Part must be in

place as shown

for proper ice

dispensing. Food

cannot be stored

in this location.

ge.com

Not all features are on all models.

Slide-Out Freezer Shelves

To remove,

slide out to the

stop

position,

lift the front past the stop position and

slide out.

Make sure you push the shelves all the way back

in before you close the door.

Freezer Baskets

To remove,

push the basket all the way to the

back of the freezer. Lift up until the back

pins are disengaged. Lift the entire basket

up and pull out.

Make sure you push the baskets all the way back

in before you close the door.

Fixed Freezer Shelves

There are two types of fixed

freezer shelves.

To remove this type of shelf:

Lift the shelf up at the left side.

Bring the shelf out.

To remove this type of shelf:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up

and out of the shelf supports.

NOTE FOR DISPENSER MODELS: In order to take

full advantage of the tilt-out ice bin, only store items

on the shelf below the ice bin that are no taller than

the lowest point on the bin.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Door Wine/Beverage Rack (on some models)

This rack holds up to 5 cans or one bottle

of wine.

The rack hangs from the sides of the

dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin,

lift the front straight up, then lift up

and out.

To detach the rack from the dairy bin,

pull the rack’s side wires out of the

holes on each side of the dairy bin.

To replace:

Reattach the rack to the sides

of the bin.

Engage the back side of the bin in

the molded supports on the door.

Then push down on the front of the

bin. The bin will lock into place.

11

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

12

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different

than the ones you are used to. The special

door opening/closing feature makes sure

the doors close all the way and are securely

sealed.

When opening and closing the door you

will notice a

stop

position. If the door is

opened past this

stop

point, the door will

remain open to allow you to load and

unload food more easily. When the door

is only partially open, it will automatically

close.

The resistance you feel at the

stop

position will be reduced as the door

is loaded with food.

When the door is only partially open,

it will automatically close.

Beyond this stop the door will stay open.

Door Alignment

If doors are uneven, adjust the refrigerator

door.

Using a 7/16″ wrench, turn the door

adjusting screw to the right to raise the

door, to the left to lower it. (A nylon

plug, imbedded in the threads of the

pin, prevents the pin from turning

unless a wrench is used.)

After one or two turns of the wrench,

open and close the refrigerator door

and check the alignment at the top of

the doors.

7/16″ Wrench

Raise

Support Leg

Before moving the refrigerator, you will

need to screw up the support leg. Once the

unit is relocated, you will need to screw

down the support leg again.

Screw down the support

leg until it touches the

floor. This will prevent

door misalignment.

About the crispers and pans. ge.com

13

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling

the drawer straight out and lifting the

drawer up and over the

stop

location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers should be wiped dry.

On some models,

the bottom drawer has

full extension slides that allow full access

to the drawer.

Adjustable Humidity Crispers

Slide the control all the way to the

HI

setting

to provide high humidity recommended for

most vegetables.

Slide the control all the way to the

LO

setting to provide lower humidity levels

recommended for most fruits.

HI LO

Convertible Deli Pan

The convertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or fresh food

compartment to flow to the pan.

The variable temperature control

regulates

the air flow from the Climate Keeper.

Set the control to the

coldest

setting to

store fresh meats.

Set the control to

cold

to convert the pan

to normal refrigerator temperature and

provide extra vegetable storage space. The

cold air duct is turned off. Variable settings

between these extremes can be selected.

C

O

L

D

C

O

L

D

E

S

T

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

About the automatic icemaker.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

14

Automatic Icemaker

The icemaker will produce seven cubes

per cycle—approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room

temperature, number of door openings

and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch in the

O (off)

position.

When the refrigerator has been connected

to the water supply, set the power switch to

the

l (on)

position.

The icemaker will fill with water when it

cools to 15°F (–10°C). A newly installed

refrigerator may take 12 to 24 hours to begin

making ice cubes.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing

ice. It is normal for several cubes to be

joined together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

Special note about dispenser models:

■ Dispenser models have a tilt-out ice bin.

The bin can be tilted out as shown in the

illustrations, and it will hold itself up

while you take ice out or turn the

icemaker power switch on and off. Be

sure to put the bin back in place before

closing the door.

■ To restore your ice level from an empty

bucket stage, the following steps are

recommended:

12 hours after the first batch of ice

has fallen into the bin, dispense

3 to 4 cubes.

After an additional 6 hours, dispense

3 to 4 cubes again.

These steps will restore your ice level

in the shortest amount of time.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Lift the bin, then pull it

forward until the bin stops.

Removing Ice Bin (dispenser models)

CAUTION: The ice bin is heavy when full.

Set the power switch to the

O (off)

position

before removing the bin.

When replacing the bin,

be sure to press it

firmly into place. If it does not go all the

way back, remove it and rotate the drive

mechanism 1/4 turn. Then push the bin

back again.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Lower the bin to access ice

or reach the power switch.

NOTE: In order to take full advantage

of the tilt-out ice bin, only store items

on the shelf below the ice bin that

are no taller than the lowest point

on the bin.

On dispenser models,

to access ice or reach

the power switch:

Lift the bin, then pull it

forward until the bin stops.

Lift and pull forward again

to remove the bin.

Rotate

Drive

Mechanism

Dispenser Models only

About the ice and water dispenser. (on some models) ge.com

To Use the Dispenser

Select

CUBED, CRUSHED

or

WATER.

Press the glass gently against the top of the

dispenser cradle.

The spill shelf is not self-draining. To reduce

water spotting, the shelf and its grille should be

cleaned regularly.

If no water is dispensed when the refrigerator is first

installed, there may be air in the water line system. Press

the dispenser arm for at least two minutes to remove

trapped air from the water line and to fill the water

system. To flush out impurities in the water line, throw

away the first six glassfuls of water.

CAUTION: Never put fingers or any other objects into

the ice crusher discharge opening.

Locking the Dispenser

Press the

LOCK

pad for 3 seconds to lock the

dispenser and control panel. To unlock, press

and hold the pad again for 3 seconds.

Dispenser Light

The

LIGHT

pad turns the

night light

in the

dispenser on and off. The light also comes on

when the dispenser cradle is pressed. On some

models, if this light burns out, it should be

replaced with a 6 watt 12V maximum bulb.

Door Alarm

Use

Door Alarm

to sound if either door is open

for more than 3 minutes. The alarm will stop

once the door is closed. For LCD models, a

popup screen will appear. The alarm can be

silenced by touching the LCD screen.

LCD Models:

Access By:

Home > Options > Information and

Settings > Settings > Door Alarm

Access By:

Pressing

ON

.

Deactivate By:

Pressing

OFF

.

Non-LCD Models:

Press the

DOOR ALARM

pad until the indicator

light comes on.

Spill Shelf

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Precise Fill (on some models)

Quick Ice

This water dispenser is equipped with a feature

called “precise fill.” This feature allows you to

choose a precise amount of water (cups or

ounces) that you would like dispensed. Pints

and Liters are also available for LCD models.

LCD Models

Access By:

Home > Options > Dispenser

Options > Precise Fill > Set Amount

Activate By:

Using the arrow buttons to select

the desired amount. Press

MORE UNITS

to select

between CUPS, OUNCES, PINTS or LITERS.

Non-LCD Models

Press the

WATER

pad.

Press the

CUPS

or

OUNCES

pad.

Select the precise amount of water you

would like dispensed.

If you selected OUNCES,

press the arrow

pads on either side of the display to

select the number of ounces you

would like to have dispensed between

1–99 ounces.

If you selected CUPS,

press the arrow

pads on the left of the display to select

the whole cups (1–16 cups) and/or

the arrow pads on the right side of the

display to select fractions of a cup

(1/4–3/4 cups).

Press the cup against the cradle and water

will begin dispensing. It will automatically

stop when the amount set has been

dispensed. The display will show there

is no water left to dispense, then reset.

NOTE: Do not leave the dispenser unattended when

water is being dispensed.

If you would like to stop dispensing water

before the specified amount has been

dispensed, just remove the cup from the

cradle. The display will show the amount

left to dispense.

When you need to speed up ice production, use

the

Quick Ice

feature. While this feature is turned

on, the freezer fan runs continuously for 48 hours,

or until the feature is turned OFF. During this

period, ice production will increase up to 40%.

Models with the integrated ice feature system

require at FIRST USE at least half an 8 oz. glass

of ice to be dispensed every 6 to 12 hours. This

will help the icemaker fill the bucket properly

so that dispensing is better.

How to Use

LCD Models:

Access by:

Home > Options > Freezer Options >

Quick Ice

Activate by:

Pressing

ON

.

Deactivate by:

Pressing

OFF

.

Non-LCD Models:

Press the

QUICK ICE

pad to turn the feature ON.

Press the pad again to turn the feature OFF.

15

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

16

Cleaning the Outside

The dispenser drip area,

beneath the grille,

should be wiped dry. Water left in this area

may leave deposits. Remove the deposits by

adding undiluted vinegar to the well. Soak

until the deposits disappear or become

loose enough to rinse away.

The dispenser cradle

. Before cleaning, lock

the dispenser by pressing and holding the

LOCK

pad for 3 seconds. Clean with warm

water and baking soda solution—about a

tablespoon (15 ml) of baking soda to a

quart (1 liter) of water. Rinse thoroughly

and wipe dry.

The door handles and trim.

Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with

a commercially available stainless steel

cleaner. A spray-on stainless steel cleaner

works best.

Do not use appliance wax or polish

on the stainless steel.

Keep the outside clean.

Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish detergent.

Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish

cloth or wet towel. These may leave a residue

that can erode the paint. Do not use scouring

pads, powdered cleaners, bleach or cleaners

containing bleach because these products can

scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors,

leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning.

If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and

wipe dry.

Use of any cleaning solution other than that

which is recommended, especially those that

contain petroleum distillates, can crack or

damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water

because the extreme temperature difference

may cause them to break. Handle glass shelves

carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts

in the dishwasher.

The chill/thaw tray is dishwasher safe.

Dispenser drip area.

Care and cleaning of the refrigerator.

About the ice and water dispenser. (on some models)

Important Facts About Your Dispenser

■Do not add ice from trays or bags to

the storage drawer. It may not crush or

dispense well.

■Avoid overfilling glass with ice and use

of narrow glasses. Backed-up ice can

jam the chute or cause the door in the

chute to freeze shut. If ice is blocking

the chute, poke it through with a

wooden spoon.

■Beverages and foods should not be

quick-chilled in the ice storage drawer.

Cans, bottles or food packages in the

storage drawer may cause the icemaker

or auger to jam.

■To keep dispensed ice from missing

the glass, put the glass close to, but not

touching, the dispenser opening.

■Some crushed ice may be dispensed

even though you selected

CUBED

.

This happens occasionally when a few

cubes accidentally get directed to

the crusher.

■After crushed ice is dispensed, some

water may drip from the chute.

■Sometimes a small mound of snow

will form on the door in the ice chute.

This condition is normal and usually

occurs when you have dispensed

crushed ice repeatedly. The snow

will eventually evaporate.

17

For long vacations or absences, remove

food and unplug the refrigerator. Clean the

interior with a baking soda solution of one

tablespoon (15 ml) of baking soda to one

quart (1 liter) of water. Leave the doors

open.

Set the icemaker power switch to the

O (off)

position and shut off the water supply to

the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system to prevent serious property

damage due to flooding.

ge.com

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure

you don’t roll over the power cord or icemaker

supply line.

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and

drawers by taping them securely in place

to prevent damage.

When using a hand truck to move the

refrigerator, do not rest the front or back

of the refrigerator against the hand truck.

This could damage the refrigerator. Handle

only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright

position during moving.

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

18

Replacing the light bulbs.

Setting the controls to OFF does not remove power to the light circuit.

Not all features are on all models.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.

The bulbs are located at the top of the

compartment, inside the light shield.

On some models, a screw at the front of

the light shield will have to be removed.

On other models, the screw is located

in the pocket located at the back of the

light shield.

To remove the light shield, on some

models, press in on the tabs on the

sides of the shield and slide forward

and out. On other models, just slide

the shield forward and out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the light shield and

screws (on some models). When

replacing the light shield, make sure

that the tabs at the back of the shield

fit into the slots at the back of the light

shield housing.

Plug the refrigerator back in.

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.

Remove the convertible meat drawer

control knob by pulling straight out.

Lift the light shield up and pull it out.

After replacing the bulb with an

appliance bulb of the same or lower

wattage, replace the shield and

the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light

shield. (The shelf will be easier to

remove if it is emptied first.) On some

models, a screw at the top of the light

shield will need to be removed.

To remove the light shield, press in

on the sides, and lift up and out.

Replace the bulb with an appliance

bulb of the same or lower wattage,

and reinstall the light shield. When

reinstalling the light shield, make

sure the top tabs snap securely

into place. Replace the screw

(on some models).

Reinstall the shelf and plug the

refrigerator back in.

C

O

L

D

C

O

L

D

E

S

T

Dispenser (on some models)

Unplug the refrigerator.

The bulb is located on the dispenser

under the control panel.

Remove the light bulb by turning

it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage.

Plug the refrigerator back in.

Tabs

Pocket

OR

Your light shield will look like

one of the following:

19

Trim kits and decorator panels.

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels. You can order

pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,

800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4

″

(6 mm) thick

When installing wood panels less than 1/4″ (6 mm) thick, you need to create a filler panel, such as 1/8″

cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut

decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator

or wood panel and the filler panel should be 1/4″ (6 mm).

For CustomStyle

™

models

3/4

″

(19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4″ (6 mm) thick backing, or a 3/4″ (19 mm) routed board

can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2″ (5.1 cm)

from the handle side for fingertip clearance.

Panels thicker than 1/4″ (6 mm), up to 3/4″ (19 mm) max, will require that the outer 5/16″ (8 mm) of

panel perimeter be no thicker than 1/4″ (6 mm).

Weight limitations for custom panels:

Fresh Food 38 lbs. (17 kg) max.

Freezer Door 28 lbs. (13 kg) max.

2″(5.1 cm)

Clearance

Handle Side

Appearance

Panel

Refrigerator

Door

1/4″(6 mm)

Thick Backing

3/4″

(19 mm)

Panels 1/4″thick or less

Panels thicker than 1/4″(6 mm)

1/4″max

1/4″(6 mm) max

3/4″(19 mm)

5/16″ (8 mm)

Consumer SupportTroubleshooting Tips

Operating InstructionsSafety Instructions

Installation Instructions

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

20

Trim kits and decorator panels.

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser Fresh Food Panel

Cutout

5/16″

(8 mm)

14

15

⁄32″

(36.8 cm)

67

9

⁄32″

(170.9 cm)

1/8″ (3 mm)

FRONT

17

7

⁄8″

(45.4 cm)

14

15

⁄32″

(36.8 cm)

33

5

⁄8″

(85.4 cm)

FRONT

67

9

⁄32″

(170.9 cm)

19

15

⁄32″

(49.5 cm)

FRONT

23‘ Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

25‘

CustomStyle

™

Dimensions for Custom Wood Panels

The areas at the top of the panels need to be cut out of the panels.

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

5/16″

(8 mm)

Freezer Panel

Without Dispenser

Freezer Panel

With Dispenser Fresh Food Panel

Cutout

5/16″

(8 mm)

14

15

⁄32″

(36.8 cm)

69″

(175.3 cm)

1/8″ (3 mm)

FRONT

17″

(43.2 cm)

14

15

⁄32″

(36.8 cm)

36

1

⁄4″

(92.0 cm)

FRONT

69″

(175.3 cm)

19

15

⁄32″

(49.5 cm)

FRONT

Cutout

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

5/16″

(8 mm)

Cutout

5/16″

(8 mm)

1/8″ (3 mm)

Cutout

5/16″

(8 mm)

1/8″ (3 mm)

Cutout

5/16″

(8 mm)

1/8″ (3 mm)

Cutout

1/8″ (3 mm)

5/16″

(8 mm)

Cutout

1/8″ (3 mm)

Cutout

5/16″

(8 mm)

1/8″ (3 mm)

5/16″

(8 mm)

La page est en cours de chargement...

GE Profile PSS26NSWSS Manuel utilisateur

GE Profile PSS26NSWSS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents