Troy-Bilt Trimmer TB26CO Manuel utilisateur

Marque: Troy-Bilt

Modèle: Trimmer TB26CO

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

TB26CO

Operator’s Manual

4-Cycle Gasoline Trimmer

TB26CO

SAVE THESE INSTRUCTIONS

For service call 1-800-520-5520 to obtain a list of authorized

service dealers near you. For more details about your unit, visit

our website at www.troybilt.com.

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY

SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty period

should be performed only by an authorized and approved

service dealer.

All information, illustrations, and specifications in this manual

are based on the latest product information available at the

time of printing. We reserve the right to make changes at any

time without notice.

WARNING: When using the unit, you must follow

the safety rules. Please read these instructions

before operating the unit in order to ensure the

safety of the operator and any bystanders. Please

keep these instructions for later use.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest

Land and the state of California (Public Resources Codes 4442

and 4443), Oregon and Washington require, by law that certain

internal combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention of

fire. Check with your state or local authorities for regulations

pertaining to these requirements. Failure to follow these

requirements could subject you to liability or a fine. This unit is

factory equipped with a spark arrestor. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #791-180890 Spark Arrestor Kit.

CALIFORNIA PROPOSITION 65 WARNING

P/N 769-02062 (11/05)

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . .2

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Starting/Stopping Instructions . . . . . . . . . . . . . . . . . . . . . .5

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Maintenance and Repair Instructions . . . . . . . . . . . . . . . .6

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E17

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls

and proper use of the unit.

• Do not operate this unit when tired, ill, or under the influence

of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use the

unit, except for teens guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check

for fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

• Carefully inspect the area before starting the unit. Remove

all debris and hard or sharp objects such as glass, wire, etc.

• Be aware of the risk of injury to the head, hands and feet.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets outside a

50 feet (15 m.) radius; there still may be a risk to bystanders

from thrown objects. Bystanders should be encouraged to

wear eye protection. If you are approached, stop the unit

immediately.

• Use only 0.080 inch, 2.03 mm diameter original equipment

manufacturer replace-ment line. Never use metal-reinforced

line, wire or rope. These can break off and become

dangerous projectiles.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling the

fuel tank. Never remove the fuel tank cap or add fuel when

the engine is hot. Never operate the unit without the fuel cap

securely in place. Loosen the fuel tank cap slowly to relieve

any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where there

are no sparks or flames. Remove the fuel cap slowly, and

only after the engine stops. Do not smoke while fueling.

Wipe up any spilled fuel from the unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling source

and site before starting the engine. Do not smoke. Keep

sparks and open flames away from the area while adding

fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can be fatal. Operate this unit only

in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or dust

mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long sleeve

shirt. Do not wear loose clothing, jewelry, short pants,

sandals or go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place while

operating the unit as a trimmer. Do not operate unit without

both trimming lines extended, and the proper line installed. Do

not extend the trimming line beyond the length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have the

unit adjusted by an authorized service technician.

• Adjust the handle to your size in order to provide the best grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable

position while starting. Refer to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended purpose.

• Do not overreach. Always keep proper footing and balance.

• Always hold the unit with both hands when operating. Keep

a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all moving

parts. Do not touch or try to stop the cutting attachment

when it rotates.

• Do not touch the engine, gear housing or muffler. These

parts get extremely hot from operation, even after the unit is

turned off.

• Do not operate the engine faster than the speed needed to

cut, trim or edge. Do not run the engine at high speed when

not cutting.

• Always stop the engine when cutting is delayed or when

walking from one cutting location to another.

• If you strike or become entangled with a foreign object, stop

the engine immediately and check for damage. Do not

operate before repairing damage. Do not operate the unit

with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect the

spark plug for maintenance or repair.

• Use only original equipment manufacturer replacement parts

and accessories for this unit. These are available from your

authorized service dealer. Use of any unauthorized parts or

accessories could lead to serious injury to the user, or

damage to the unit, and void your warranty.

• Keep unit clean of vegetation and other materials. They may

become lodged between the cutting attachment and shield.

• To reduce fire hazard, replace a faulty muffler and spark

arrestor. Keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing or transporting. Be

sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to prevent

unauthorized use or damage, out of the reach of children.

• Never douse or squirt the unit with water or any other liquid.

Keep handles dry, clean and free from debris. Clean after

each use, see Cleaning and Storage instructions.

• Keep these instructions. Refer to them often and use them

to instruct other users. If you loan someone this unit, also

loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING: Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following

precautions:

RULES FOR SAFE OPERATION

SYMBOL MEANING

• ON/OFF STOP CONTROL

ON / START / RUN

• WARNING - READ OPERATOR'S MANUAL

Read the operator’s manual(s) and follow all warnings

and safety instructions. Failure to do so can result in

serious injury to the operator and/or bystanders.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the

operator's manual for complete safety, assembly, operating and maintenance and repair information.

• ON/OFF STOP CONTROL

OFF or STOP

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used

in conjunction with other symbols or pictographs.

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye

protection meeting ANSI Z87.1 standards and ear

protection when operating this unit. Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially

children and pets, at least 50 feet (15 m) from the

operating area.

• THROWN OBJECTS AND ROTATING CUTTER

CAN CAUSE SEVERE INJURY

WARNING: Do not operate without the cutting

attachment shield in place. Keep away from the

rotating cutting attachment.

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder.

You may get burned. These parts get extremely hot

from operation. They remain hot for a short time after

the unit is turned off.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel

• OIL

Refer to operator’s manual for the proper type of

oil.

• SHARP BLADE

WARNING: Sharp blade on cutting attachment

shield. To prevent serious injury, do not touch the

line cutting blade.

OIL AND FUEL INFORMATION

RECOMMENDED OIL TYPE

Using the proper type and weight of oil in the crankcase is

extremely important. Check the oil before each use and

change the oil regularly. Failure to use the correct oil, or using

dirty oil, can cause premature engine wear and failure.

Use a high-quality SAE 30 weight oil of API (American

Petroleum Institute) service class SF, SG, SH.

ADDING OIL TO CRANKCASE: INITIAL USE

NOTE: This unit is shipped without oil. In order to avoid

damage to the unit, put oil in the crankcase before you

attempt to start the unit.

Your unit is supplied with one 3.04

fluid oz. (90 ml.) bottle of SAE 30

SF, SG, SH oil (Fig. 1).

NOTE: Save the bottle of oil. It

can be used to measure the

correct amount during future

oil changes. See Changing

the Oil.

1. Unscrew the top of the bottle of oil and remove the paper

WARNING: OVERFILLING OIL CRANKCASE MAY

CAUSE SERIOUS PERSONAL INJURY. Check and

maintain the proper oil level in the crank case; it is

important and cannot be overemphasized. Check the

oil before each use and change it as needed. See

Changing the Oil.

Fig. 1

Funnel

Spout

seal covering the

opening. Replace the

top. Next, cut the tip off

the funnel spout (Fig. 1).

2. Place the unit on a flat

level surface (Fig. 2).

3. Remove the dipstick

from the crankcase (Fig.

3).

4. Pour the entire bottle

of oil into the oil fill

hole (Fig. 3).

NOTE: Never add oil to

the fuel or fuel tank.

5. Wipe up any oil that

may have spilled and

reinstall the oil fill plug/

dipstick.

Check oil before each use and change as needed. Refer to

Checking the Oil Level.

RECOMMENDED FUEL TYPE

Old fuel is the primary reason for improper unit performance.

Be sure to use fresh, clean, unleaded gasoline.

NOTE: This is a four cycle engine. In order to avoid damage to

the unit, do not mix oil with gasoline.

Fig. 2

Oil Fill

Oil Fill Plug/

Dipstick

Oil Fill Hole

Fig. 3

O-Ring

• PRIMER BULB

Push primer bulb, fully and slowly, 10 times.

Cutting Attachment

Shield

Fuel

Cap

Throttle

Control

D-Handle

Cutting

Attachment

Shaft Grip

Primer

Bulb

Oil Fill Plug / Dipstick

Spark

Plug

Shaft

Starter Rope Grip

Line

Cutting

Blade

Spark

Plug

Muffler

Muffler Guard

Spark Arrestor

On/Off Stop

Control

KNOW YOUR UNIT

Air Filter

Cover

OIL AND FUEL INFORMATION

ASSEMBLY INSTRUCTIONS

INSTALL AND ADJUST THE D-HANDLE

1. Push the D-handle down onto the shaft housing so that the

handle slants towards the shaft grip (Fig. 5). The squared

bolt hole in the handle is to the right.

2. Insert the shoulder bolt into the squared hole in the handle

and push through.

On the left side of

the handle, place

the washer on the

bolt, then screw the

wing nut onto the

bolt. Do not tighten

until you make the

handle adjustment.

3. Rotate the D-handle

to place the grip

above the top of the

shaft housing. Place it a minimum of 6 inches (15.24 cm)

from the end of the shaft grip.

4. While holding the unit in the operating position (Fig. 10),

position the D-handle to the location that provides you the

best grip.

5. Tighten the wing nut until the D-handle is secure.

Fig. 5

Bolt

Washer

Wing

Nut

Tighten

Shaft

Grip

D-Handle

Minimum

6 inches

(15.24 cm)

Shaft

Housing

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates

such as ethanol, methanol or MTBE (ether). Alcohol-blended

fuel absorbs water. As little as 1% water in the fuel can make

fuel and oil separate or form acids when stored. Use fresh fuel

(less than 60 days old), when using alcohol-blended fuel.

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable,

follow recommended precautions:

• Always use fresh unleaded gasoline

• Use the fuel additive STA-BIL

or an equivalent

• Drain tank and run the engine dry before storing unit

Using Fuel Additives

The use of fuel additives, such as STA-BIL

Gas Stabilizer or

an equivalent, will inhibit corrosion and minimize the formation

of gum deposits. Using a fuel additive can keep fuel from

forming harmful deposits in the carburetor for up to six (6)

months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel

according to the instructions on the container. NEVER add fuel

additives directly to the unit's gas tank.

FUELING THE UNIT

1. Remove the fuel cap (Fig. 4).

2. Place the gas container’s spout into the fill hole on the fuel

tank (Fig. 4) and fill the tank.

NOTE: Do not overfill the tank.

3. Wipe up any gasoline that may have spilled.

4. Reinstall the fuel cap.

5. Move the unit at least 30 ft. (9.1 m) from the fueling source

and site before starting the engine.

NOTE: Dispose of the old gasoline in accordance to Federal,

State and Local regulations.

WARNING: Add fuel in a clean, well ventilated

outdoor area. Wipe up any spilled fuel immediately.

Avoid creating a source of ignition for spilt fuel. Do

not start the engine until fuel vapors dissipate.

WARNING: Gasoline is extremely flammable.

Ignited vapors may explode. Always stop the engine

and allow it to cool before filling the fuel tank. Do not

smoke while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap slowly to avoid injury

from fuel spray. Never operate the unit without the

fuel cap securely in place

Fig. 4

Fuel Cap

Fuel Tank

Gas Can Spout

Unleaded

Gasoline

STARTING/STOPPING INSTRUCTIONS

STARTING INSTRUCTIONS

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control. Allow the

engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position.

WARNING: Avoid accidental starting. Make sure

you are in the starting position when pulling the

starter rope (Fig. 9).

To avoid serious injury, the

operator and unit must be in a stable position while

starting.

To avoid serious personal injury, ensure any Add-

On being used is installed correctly and secure

before starting the unit.

WARNING:

Operate this unit only in a well-

ventilated outdoor area. Carbon monoxide exhaust

fumes can be lethal in a confined area.

Starter Rope

Throttle Control

Fig. 9

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

Fig. 8

Fig. 6

Start / Stop

Control

Primer

Bulb

Cold Weather

Start Lever

(Fig. 7)

Cold

Weather

Start Lever

Run/ Open

Close/ Start

Fig. 7

1. Check the oil level in the crankcase. Refer to Checking

the Oil Level.

2. Fill the fuel tank with fresh, clean unleaded gasoline.

Refer to Fueling the Unit.

3. Make sure the On/Off Stop Control in the ON ( I )

position (Fig. 6).

IF COLD...

For cold weather conditions (below 40°F),

flip the Cold Weather Start Lever (Fig. 7) down to the

start/closed position and continue to step 4. DO NOT

flip this lever down if the temperature is above 40°F.

4. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in the

primer bulb and fuel lines (Fig. 8). If you can’t see fuel

in the bulb, press and release the bulb as many times

as it takes before you can see fuel in it.

5. With the unit in the starting position, do not squeeze

the throttle control (Fig. 9). Pull the starter rope out a

short distance, until you feel some resistance. This is

usually around 2-4 inches. Then pull the rope smoothly

and briskly. Repeat this 5 times. The engine should start.

IF ENGINE

STARTS

AND WEATHER IS COLD...

(below 40°F), flip the Cold Weather Start Lever back

up to the run/open position.

6. If engine starts, squeeze the throttle control to warm

up the engine for 15 to 30 seconds. In cold weather, let

the engine warm up for 30 to 60 seconds.

IF...

the engine does not start, go back to step 3.

IF... the engine stops while you are squeezing the throttle,

go back to step 4.

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should also be

a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require special

tools or skills. If you are unsure about these procedures

take your unit to any non-road engine repair

establishment, individual or authorized service dealer.

NOTE: Maintenance, replacement, or repair of the emission

control devices and system may be performed by any non-

road engine repair establishment, individual or authorized

service dealer.

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit running.

Always service and repair a cool unit. Disconnect the

spark plug wire to ensure that the unit cannot start.

FREQUENCY MAINTENANCE REQUIRED SEE

Before starting engine

Fill fuel tank with fresh fuel

Check oil

p. 4

p. 8

Every 10 hours Clean and re-oil air filter p. 9

change at 10 hours

change at 25 hours

Every 25 hours after

Change oil

Clean spark arrestor

p. 9

p. 12

10 hours on new

engine

Every 25 hours

Check rocker arm to valve

clearance and adjust

Check rocker arm to valve

clearance and adjust

Check spark plug

condition and gap

p. 10

p. 11

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position (Fig.

10). Check for the following:

• The operator is wearing eye

protection and proper clothing

• With a slightly-bent right arm, the

operator’s right hand is holding the

shaft grip

• The operator’s left arm is straight,

the left hand holding the assist

handle

• The unit is at waist level

• The cutting attachment is parallel to

the ground and easily contacts the

grass without the need to bend over

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to release

trimming line without stopping the engine. To release more line,

lightly tap the cutting attachment on the ground (Fig. 11) while

operating the trimmer at high speed.

NOTE: Always keep the

trimming line fully

extended. Line release

becomes more

difficult as the cutting

line becomes shorter.

Each time the head is

bumped, about 1 inch

(25.4 mm) of trimming

line is released. A blade

in the cutting attachment shield will cut the line to the proper

length if excess line is released.

For best results, tap the Bump Head™ on bare ground or hard

soil. If line release is attempted in tall grass, the engine may

stall. Always keep the trimming line fully extended. Line release

becomes more difficult as the cutting line becomes shorter.

NOTE: Do not rest the Bump Head™ on the ground while the

unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence posts

TIPS FOR BEST TRIMMING RESULTS

• For best trimming results, operate unit at full throttle.

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of the line to do

the cutting, especially along walls. Cutting with more than the tip

will reduce cutting efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from top to bottom

in small increments to avoid premature line wear or engine drag.

• Cutting from right to left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting area at the

desired height. Move either in a forward-backward or side-to-

side motion. Cutting shorter lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon proper

adherence of explained trimming techniques, what

vegetation is cut, and where vegetation is cut.

For example, the line will wear faster when trimming against a

foundation wall as opposed to trimming around a tree.

DECORATIVE TRIMMING

Decorative trimming is

accomplished by removing all

vegetation around trees, posts,

fences and more.

Rotate the whole unit so that the

cutting attachment is at a 30°

angle to the ground (Fig. 12).

OPERATING INSTRUCTIONS

WARNING: Do not remove or alter the line cutting

blade assembly. Excessive line length will make the

clutch overheat. This may lead to serious personal

injury or damage to the unit.

WARNING: Always wear eye, hearing, foot and

body protection to reduce the risk of injury when

operating this unit.

Fig. 10

Fig. 12

Fig. 11

MAINTENANCE AND REPAIR INSTRUCTIONS

NOTE: SplitLine™ can only be used with the inner reel with

the slotted holes. Single line can be used on either type of

inner reel. Use Figure 16 to identify the inner reel you have.

NOTE: Always use the correct line length when installing

trimming line on the unit. The line may not release properly if

the line is too long.

Single Line Installation

Go To Step 8 for SplitLine™ Installation

6. Take approximately 16 feet (5 m) of new trimming line, loop it

into two equal lengths. Insert each end of the line through one

of the two holes in the inner reel (Fig. 17). Pull the line through

the inner reel so that the loop is as small as possible.

7. Wind the lines in tight even layers, onto the reel (Fig. 18).

Wind the line in the direction indicated on the inner reel.

Place your index finger between the two lines to stop the

lines from overlapping. Do not overlap the ends of the line.

Proceed to step 11.

SplitLine™ Installation

8. Take approximately 8 feet (2.5 m) of new trimming line. Insert

one end of the line through one of the two holes in the inner

reel (Fig. 19). Pull the line through the inner reel until only

about 4 inches is left out.

9. Insert the end of the line into the open hole in the inner reel

and pull the line tight to make the loop as small as possible

(Fig. 19).

LINE INSTALLATION

This section covers both SplitLine™ and standard single line

installation.

Always use original equipment manufacturer replacement line.

Use 0.080 in. (2.03 mm) line. Line other than the specified may

make the engine overheat or fail.

There are two methods to replace the trimming line:

• Wind the inner reel with new line

• Install a prewound inner reel

Winding the Existing Inner Reel

1. Hold the outer spool with one hand and unscrew the Bump

Knob counterclockwise (Fig. 13). Inspect the bolt inside the

bump knob to make sure it moves freely. Replace the bump

knob if damaged.

2. Remove the inner reel from outer spool (Fig. 13).

3. Remove spring from the

inner reel (Fig. 13).

4. Use a clean cloth to clean the

the inner reel, spring, shaft

and inner surface of the outer

spool (Fig. 14).

5. Check the indexing teeth on

the inner reel and outer spool

for wear (Fig. 15). If necessary,

remove burrs or replace the

reel and spool.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: Never use metal-reinforced line, wire,

chain or rope. These can break off and become

dangerous projectiles.

Bump

Knob™

Bolt

Inner

Reel

Spring

Outer Spool

Fig. 13

Indexing Teeth

Fig. 15

Fig. 14

Loop

Fig. 17

Fig. 18

Fig. 16

Slotted

Holes

For Use with SplitLine™

or Single Line

For Use with Single

Line ONLY

MAINTENANCE AND REPAIR INSTRUCTIONS

10. Before winding, split the line back about 6 inches.

11. Wind the line in tight even layers in the direction indicated

on the inner reel.

NOTE: Failure to wind the line in the direction indicated will cause

the cutting attachment to operate incorrectly.

12. Insert the ends of the line into the two holding slots (Fig. 20).

13. Insert the ends of the line through the eyelets in the outer

spool and place inner reel with spring inside the outer spool

(Fig. 21). Push the inner reel and outer spool together.

While holding the inner reel and outer spool, grasp the

ends and pull firmly to release the line from the holding

slots in the reel.

NOTE: The spring must be assembled on the inner reel before

reassembling the cutting attachment.

14. Hold the inner reel in place and install the bump knob by

turning clockwise. Tighten securely.

Installing a Prewound Wheel

1. Hold the outer spool with one hand and unscrew the bump

knob counterclockwise. Inspect the bolt inside the bump

knob to make sure it moves freely. Replace the bump knob if

damaged (Fig. 13).

2. Remove the old inner reel from the outer spool (Fig. 13).

3. Remove the spring from the old inner reel (Fig. 13).

4. Place the spring in the new inner reel.

Loop

Fig. 19

Holding Slots

Fig. 20

Spring

Eyelet

Fig. 21

NOTE: The spring must be assembled on the inner reel before

reassembling the cutting attachment.

5. Insert the ends of the line through the eyelets in the outer

spool (Fig. 21).

6. Place the new inner reel inside the outer spool. Push the inner

reel and outer spool together. While holding the inner reel and

outer spool, grasp the ends and pull firmly to release the line

from the holding slots in the spool.

7. Hold the inner reel in place and install the bump knob by

turning clockwise. Tighten securely.

CHECKING THE OIL LEVEL

The importance of checking and maintaining the proper oil level

in the crankcase cannot be overemphasized. Check oil before

each use:

1. Stop the engine and allow oil to drain into the crankcase.

2. Place the unit on a flat, level surface to get a proper oil level

reading (Fig. 2).

3. Keep dirt, grass clippings and other debris out of the engine.

Clean the area around the dipstick before removing it.

4. Remove the oil fill

plug/dipstick and

wipe off oil. Reinsert it

all the way back in.

5. Remove the oil fill

plug/ dipstick and

check the oil level. Oil

should be up to the

top of the dipstick (Fig.

22).

6. If the level is low, add

a small amount of oil

to the oil fill hole and

recheck (Fig. 23).

Repeat this procedure

until the oil level

reaches the top of the

dipstick.

NOTE: Do not overfill the

unit.

NOTE: Make sure the O-

ring is in place on the

oil fill plug/dipstick

when checking and

changing the oil (Fig. 23).

CAUTION: To prevent extensive engine wear and

damage to the unit, always maintain the proper oil

level in the crankcase. Never operate the unit with

the oil level below the bottom of the dipstick.

Top of Dipstick

O-Ring

Oil Fill Plug/Dipstick

Fig. 22

Full

Add 1.4-

1.5 Oz.

(41-44 ml)

Fig. 23

Oil Fill Plug/

Dipstick

Oil Fill Hole

O-Ring

MAINTENANCE AND REPAIR INSTRUCTIONS

CHANGING THE OIL

For a new engine, change the oil after the first 10 hours of

operation. Change the oil while the engine is still warm. The oil will

flow freely and carry away more impurities.

1. Unplug spark plug boot to prevent accidental starting.

2. Remove the oil fill plug/dipstick.

3. Pour the oil out of the

oil fill hole and into a

container by tipping the

unit to a vertical

position (Fig. 24). Allow

ample time for

complete drainage.

4. Wipe up any oil residue

on the unit and clean

up any oil that may

have spilled. Dispose of

the oil according to

Federal, State and local

regulations.

5. Refill the crankcase

with 3.04 fluid ounce

(90 ml) of SAE 30 SF, SG, SH oil.

NOTE: Use the bottle and spout saved from initial use to

measure the correct amount of oil. The top of the label on

the bottle measures approximately 3.04 ounces (90 ml) (Fig.

25). Check the level with the dipstick. If the level is low, add

a small amount of oil and recheck. Do not overfill (Fig. 25).

6. Replace the oil fill plug/dipstick.

7. Reconnect the spark plug boot.

AIR FILTER MAINTENANCE

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation. It is

an important item to maintain. Failure to maintain your air filter

properly can result in poor performance or can cause

permanent damage to your engine.

1. Open the air filter cover. Push the tab on the right side of

the cover inward. Then pull the air filter cover out and to

the left (Fig. 26).

WARNING: Wear gloves to prevent injury when

handling unit.

Fig. 24

Fill Level

Fig. 25

NOTE: It may be necessary to

remove the fuel cap to

completely remove the air filter

cover.

2. Remove the air filter (Fig. 26).

3. Wash the filter in detergent and

water (Fig. 27). Rinse the filter

thoroughly and allow it to dry.

4. Apply enough clean SAE 30

motor oil to lightly coat the filter

(Fig. 28).

5. Squeeze the filter to spread

and remove excess oil (Fig. 29).

6. Replace the filter

(Fig. 30).

NOTE: If the unit is

operated without

the air filter, you

will VOID the

warranty.

7. Reinstall the air

filter cover.

Position the

hooks on the left

side of the air

filter cover into

the slots at the left side of the back plate (Fig. 30).

NOTE: It may be necessary to remove the fuel cap to reinstall

the air filter cover.

8. Swing the cover to the right until the tab on the air filter

cover snaps into place in the slot on the back plate (Fig. 31).

9. Replace the fuel cap if it was removed.

WARNING: To avoid serious personal injury,

always turn the unit off and allow it to cool before

you clean or service it.

Fig. 27

Air Filter

Air Filter Cover

Tab

Fig. 26

Fig. 28

Fig. 29

Fig. 30

Back Plate Slot

Slots

Back Plate

Checking the fuel, cleaning the air filter, and adjusting the idle

speed should solve most engine problems. If not and all of the

following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

ROCKER ARM CLEARANCE

This requires disassembly of the engine. If you feel unsure or

unqualified to perform this, take the unit to an authorized

service center.

NOTE: Inspect the valve to rocker arm clearance with a feeler

gauge after the first 10 hours of operation and then every

25 hours of operation thereafter.

• The engine must be cold when checking or adjusting the

valve clearance.

• This task should be performed inside, in a clean, dust free

area.

1. Remove the muffler cover by pressing down on it,

separating it from the engine cover. Using a flat blade

screwdriver, disengage the middle and front tabs and slots

first. The cover will hinge off from the rear tab (Fig. 33).

2. Remove the two (2) screws on top of the engine cover with a

Flat-head or T-25 Torx screwdriver (Fig. 34).

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable. An idle adjustment

screw is reached though a hole in the top of the engine cover

(Fig. 32).

NOTE: Careless

adjustments can

seriously damage your

unit. An authorized

service dealer should

make carburetor

adjustments.

Check Fuel

Old fuel is usually the

reason for improper unit

performance. Drain and

refill the tank with fresh fuel

prior to making any adjustments. Refer to Oil and Fuel

Information.

Clean Air Filter

The condition of the air filter is important to the operation of the

unit. A dirty air filter will restrict air flow. This is often mistaken

for an out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to Air

Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel and cleaning the air filter, the engine

still will not idle, adjust the idle speed screw as follows:

1. Start the engine and let it run at a high idle for a minute to

warm up. Refer to Starting/Stopping Instructions.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips into the hole in the air

filter/muffler cover (Fig. 32). Turn the idle speed screw in,

clockwise, 1/8 of a turn at a time (as needed) until the engine

idles smoothly.

NOTE: The cutting attachment should not rotate when the

engine idles.

3. If the cutting attachment rotates when the engine idles, turn

the idle speed screw counterclockwise 1/8 of a turn at a

time (as needed), to reduce idle speed.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: The cutting attachment may spin during

idle speed adjustments. Wear protective clothing and

observe all safety instructions to prevent serious

personal injury.

WARNING: To prevent serious personal injury,

make sure the cutting attachment has stopped

rotating before you turn it off and set it down.

Idle Adjustment Screw

Fig. 32

Fig. 33

Engine Cover

Front Slot

Front Tab

Middle Tab

Middle Slot

Rear Slot

and Tab

Remove

Screws

Engine Cover

Fig. 34

Muffler

Top View Of The Engine

Air Filter

Cover

Tab

Fig. 31

3. Remove the screw behind

the engine cover (Fig. 35).

4. Disconnect the spark plug

wire.

5. Clean dirt from around the

spark plug. Remove the

spark plug from the cylinder

head by turning a 5/8 in.

socket counterclockwise.

6. Remove the engine cover.

7. Clean dirt from around the

rocker arm cover. Remove

the screw holding the rocker

arm cover with a large flat

blade screwdriver or Torx T-

25 bit (Fig. 36). Remove the

rocker arm cover and gasket.

8. Pull the starter rope slowly to

bring the piston to the top of its

travel, (known as top dead

center). Check that:

• The piston is at the top of its

travel while looking in the

spark plug hole (Fig. 36)

• Both rocker arms move

freely, and both valves are

closed

If these statements are not true, repeat this step.

9. Slide the feeler gauge between the rocker arm and the

valve return spring. Measure the clearance between the

valve stem and rocker arm (Fig. 37). Measure both the

intake and exhaust valves.

The recommended clearance for both intake and exhaust is

.003 – .006 in. (.076 – 0.152 mm). Use a standard automotive

.005 in. (0.127 mm) feeler gauge. The feeler gauge should slide

between the rocker arm and valve stem with a slight amount of

resistance, without binding. See Figures 37 and 38.

10. If the clearance is not within specification:

a. Turn the adjusting nut using a 5/16 inch (8 mm) wrench or

nut driver (Fig. 38).

• To increase clearance, turn the adjusting nut

counterclockwise.

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 38

• To decrease clearance, turn the adjusting nut

clockwise.

b. Recheck both clearances, and adjust as necessary.

11. Reinstall the rocker arm cover using a new gasket. Torque

the screw to 20–30 in•lb (2.2–3.4 N•m).

12. Reinstall the engine cover. Check alignment of the cover

before tightening the screws. Tighten screws.

13. Reinstall the muffler cover. Slip the rear tab on the muffler

cover into the engine cover rear slot. Then slide the

remaining slots into the tabs until they snap into place

(Fig. 33).

14. Check the spark plug and reinstall. See Replacing the

Spark Plug.

15. Replace the spark plug wire.

REPLACING THE SPARK PLUG

Use a replacement part number 791-180852B spark plug. The

correct air gap is 0.025 in. (0.655 mm.). Remove the plug after

every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug wire

firmly and pull the cap from the spark plug.

2. Clean dirt from around the spark plug. Remove the spark

plug from the cylinder head by turning a 5/8 in. socket

counterclockwise.

3. Replace cracked, fouled or

dirty spark plug. Set the air

gap at 0.025 in. (0.655 mm.)

using a feeler gauge (Fig. 39).

4. Install a correctly-gapped

spark plug in the cylinder

head. Turn the 5/8 in.

socket clockwise until snug.

If using a torque wrench torque

to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

Feeler Gauge

Adjusting Nut

Rocker Arm

.003–.006 in.

(.076–.152 mm)

Valve Stem

Screw

Fig. 35

Rocker

Arm

Cover

Fig. 36

Spark

Plug

Hole

Adjusting Nuts

Feeler Gauge

Rocker Arms

Fig. 37

INTAKE

EXHAUST

0.025 in.

(0.655 mm.)

Fig. 39

WARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the

cylinder.

SPARK ARRESTOR MAINTENANCE

1. Remove the muffler cover. See Rocker Arm Clearance.

2. With a flat blade screwdriver or Torx T-20 bit, remove the

screw attaching the spark arrestor cover to the muffler

(Fig. 40).

3. Pull the tab on the spark arrestor cover out of the muffler.

Remove the spark arrestor cover.

4. Remove the spark arrestor screen from the spark arrestor

cover.

5. Clean the spark arrestor screen with a wire brush or

replace it.

6. Reinstall the spark arrestor screen, spark arrestor cover

and screw.

CLEANING

Use a small brush to clean off the outside of the unit. Do not

use strong detergents. Household cleaners that contain

aromatic oils such as pine and lemon, and solvents such as

kerosene, can damage plastic housing or handle. Wipe off any

moisture with a soft cloth.

STORAGE

• Never store the unit with fuel in the tank where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing.

• Lock up the unit to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

1. Drain all gasoline from the gas tank into a container. Do

not use gas that has been stored for more than 60 days.

Dispose of the old gasoline in accordance to Federal,

State, and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all gasoline has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and put 1

oz. (30 ml) of high quality motor oil into the cylinder. Pull

the starter rope slowly to distribute the oil. Reinstall the

spark plug.

NOTE: Remove the spark plug and drain all of the oil from the

cylinder before attempting to start the trimmer after

storage.

4. Change the oil, referring to Changing the Oil. Dispose of

the old oil in accordance to Federal, State and Local

regulations.

5. Thoroughly clean the unit and inspect for any loose or

damaged parts. Repair or replace damaged parts and

tighten loose screws, nuts or bolts. The unit is ready for

storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Secure the unit while transporting.

• Drain the gas tank before transporting.

• Tighten gas cap before transporting.

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: To avoid serious personal injury,

always turn your unit off and allow it to cool before

you clean or service it.

Fig. 40

Muffler

Spark Arrestor Screen

Spark Arrestor Cover

Screw

Tab

Slot

TROUBLESHOOTING

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm)

of line is outside of the cutting attachment

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take to an authorized service dealer for adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

On/Off control in the STOP position

Turn On/Off control to ON

Empty fuel tank Fill fuel tank with new fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Old fuel Drain gas tank and add fresh fuel

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Adjust carburetor

CAUSE ACTION

Old fuel Drain gas tank and add fresh fuel

Improper carburetor adjustment Take to an authorized service dealer for adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

CUTTING LINE ADVANCES UNCONTROLLABLY

SPECIFICATIONS

ENGINE*

DRIVE SHAFT AND CUTTING ATTACHMENT*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes

at any time without notice.

Engine Type.................................................................................................................................................................. Air-Cooled, 4-Cycle

Displacement................................................................................................................................................................. 1.6 cu. in. (26.2 cc)

Operating RPM ........................................................................................................................................................................... 7,200+ rpm

Idle Speed RPM .............................................................................................................................................................. 2,800 - 3,600 rpm

Ignition Type.................................................................................................................................................................................. Electronic

Ignition Switch ....................................................................................................................................................................... Rocker Switch

Valve clearance...................................................................................................................................... 0.003–0.006 in. (0.076–0.152 mm)

Spark Plug Gap ........................................................................................................................................................ 0.025 inch (0.655 mm)

Lubrication ................................................................................................................................................................................... SAE 30 Oil

Crankcase Oil Capacity ........................................................................................................................................................ 3.04 oz (90 ml)

Fuel ............................................................................................................................................................................................... Unleaded

Carburetor ............................................................................................................................................................... Diaphragm, All-Position

Starter ....................................................................................................................................................................................... Auto Rewind

Muffler ............................................................................................................................................................................. Baffled with Guard

Throttle ....................................................................................................................................................................... Manual Spring Return

Fuel Tank Capacity ................................................................................................................................................................. 12 oz (355 ml)

Drive Shaft Housing ..................................................................................................................................................................... Steel Tube

Throttle Control ................................................................................................................................................................ Finger-Tip Trigger

Approximate Unit Weight (No fuel, with handle, cutting attachment and shield) ...................................................... 12-13.5 lbs (5.4-6 kg)

Cutting Mechanism............................................................................................................................................... Dual String Cutting Head

Line Spool..................................................................................................................................................................... Bump Line Releaser

Line Spool Diameter ...................................................................................................................................................... 3 inches (76.2 mm)

Trimming Line Diameter.......................................................................................................................................... 0.080 inches (2.03 mm)

Cutting Path Diameter ................................................................................................................................................ 17 inches (43.18 cm)

California / EPA Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board, the Environmental Protection Agency and Troy-Bilt LLC (Troy-Bilt) are pleased to explain the

emission control system warranty on your 2005 and later small off-road engine. New small off-road engines must be designed, built

and equipped to meet stringent anti-smog standards. Troy-Bilt must warrant the emission control system on your small off-road

engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road

engine.

Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and catalytic

converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Troy-Bilt will repair your small off-road engine at no cost to you including diagnosis, parts and

labor.

The 2005 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the

part will be repaired or replaced my Troy-Bilt.

Owners Warranty Responsibilities

• As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator’s

manual. Troy-Bilt recommends that you retain all receipts covering maintenance on your small off-road engine, but Troy-Bilt cannot

deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

• As the small off-road engine owner, you however should be aware that Troy-Bilt may deny you warranty coverage if your small off-

road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

• You are responsible for presenting your small off-road engine to a Troy-Bilt Authorized Service Center as soon as a problem exists.

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-520-5520.

Manufacturer’s Warranty Coverage

• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and

workmanship which cause the failure of a warranted part for a period of two years.

• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Troy-Bilt Service Center. For

the nearest location please contact Troy-Bilt at: 1-800-520-5520.

• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only for regular

inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any warranted part which is

scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement

point for that part.

• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the

diagnostic work is performed at an Authorized Troy-Bilt Service Center.

• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures

of warranted parts caused by the use of add-on or modified parts.

• In order to file a claim, go to your nearest Authorized Troy-Bilt Service Center. Warranty services or repairs will be provided at all

Authorized Troy-Bilt Service Centers.

• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission

related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability

may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer

• The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel

pick up/ fuel filter, ignition module, spark plug and muffler.

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose, applies

after the applicable period of express written warranty

above as to the parts as identified. No other express

warranty or guaranty, whether written or oral, except as

mentioned above, given by any person or entity, including

a dealer or retailer, with respect to any product shall bind

Troy-Bilt. During the period of the Warranty, the exclusive

remedy is repair or replacement of the product as set forth

above. (Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply

to you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales. Troy-Bilt

shall not be liable for incidental or consequential loss or

damages including, without limitation, expenses incurred

for substitute or replacement lawn care services, for

transportation or for related expenses, or for rental

expenses to temporarily replace a warranted product.

(Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration of

the safety features of the product shall void this Warranty. You

assume the risk and liability for loss, damage, or injury to you

and your property and/or to others and their property arising

out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser, original lessee or the person for whom it

was purchased as a gift.

How State Law Relates to this Warranty: This warranty gives

you specific legal rights, and you may also have other rights

which vary from state to state.

To locate your nearest service dealer dial 1-800-520-5520.

Troy-Bilt LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Troy-Bilt LLC

(“Troy-Bilt”) with respect with new merchandise purchased and

used in the United States, its possessions and territories.

Troy-Bilt warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and will, at its option, repair or

replace, free of charge, any part found to be defective in

material or workmanship. This limited warranty shall only apply

if this product has been operated and maintained in

accordance with the Operator’s Manual furnished with the

product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water or damage because of

other peril or natural disaster. Damage resulting from the

installation or use of any accessory or attachment not

approved by Troy-Bilt for use with the product(s) covered by

this manual will void your warranty as to any resulting damage.

This warranty is limited to ninety (90) days from the date of

original retail purchase for any Troy-Bilt product that is used

for rental or commercial purposes, or any other income-

producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE THROUGH YOUR LOCAL

AUTHORIZED SERVICE DEALER. To locate the dealer in your

area, please check for a listing in the Yellow Pages or contact

the Customer Service Department of Troy-Bilt by calling 1-

800-520-5520 or writing to P.O. Box 361131, Cleveland OH

44136-0019. No product returned directly to the factory will be

accepted unless prior written permission has been extended

by the Customer Service Department of Troy-Bilt.

This limited warranty does not provide coverage in the

following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools,Cutting Line,

Inner Reels, Starter Pulley,Starter Ropes, Drive Belts

C. Troy-Bilt does not extend any warranty for products sold

or exported outside of the United States of America, its

possessions and territories, except those sold through

Troy-Bilt’s authorized channels of export distribution.

Troy-Bilt reserves the right to change or improve the design of

any Troy-Bilt product without assuming any obligation to

modify any product previously manufactured.

Manuel de L’utilisateur

Désherbeuse à gaz à 4-temps

TB26CO

CONSERVEZ CES INSTRUCTIONS

Obtenez la liste des concessionnaires agréés appelez le 1-800-

520-5520. Pour de plus amples informations à propos de votre

appareil, visitez www.troybilt.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT CHEZ QUI

VOUS L'AVEZ ACHETÉ. TOUT SERVICE SOUS GARANTIE

NÉCESSITE UNE PREUVE D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS

BREVETS AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

Toutes les informations, illustrations et spécifications contenues

dans ce manuel tiennent compte des dernières informations

techniques disponibles au moment de mettre sous presse. Nous

nous réservons le droit d'y apporter des modifications à tout

moment, sans préavis.

réservés.

AVERTISSEMENT: Lorsque vous utilisez la machine,

vous devez suivre les consignes de sécurité. Veuillez lire

ces instructions avant d’opérer la machine pour vous

assurer de la sécurité de l’opérateur et de tout spectateur.

Veuillez conserver ces instructions pour un usage ultérieur.

PARE-ÉTINCELLES

REMARQUE : à l'intention des utilisateurs opérant dans les

terres forestières des États-Unis et dans les états de

Californie, du Maine, de l'Orégon et de Washington. Toutes

les terres forestières des États-Unis et de l'état de Californie

(Codes sur les ressources publiques 4442 et 4443), de l'Orégon

et de Washington exigent de par la loi que certains moteurs à

combustion interne utilisés dans des zones couvertes de taillis

ou d'herbe soient équipés d'un pare-étincelles en parfait état de

fonctionnement, ou qu'ils soient conçus, équipés et entretenus

pour la prévention des incendies. Renseignez-vous auprès des

autorités de votre province ou de votre municipalité concernant

la réglementation en vigueur. Vous pourriez être passible d'une

amende ou être tenu responsable si vous ne respectez pas cette

réglementation. Cet appareil est équipé d'un pare-étincelles en

usine. Si l'écran pare-étincelles, réf. 791-180890, doit être

remplacé, communiquez avec le service technique.

AVERTISSEMENT DE LA PROPOSITION 65 DE CALIFORNIE

P/N 769-02062 (11/05)

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . .F2

Informations sur l'huile et le carburant . . . . . . . . . . . . . .F3

Instructions de montage . . . . . . . . . . . . . . . . . . . . . . . . .F4

Familiarisez-vous avec votre appareil . . . . . . . . . . . . . . .F4

Instructions de démarrage et d'arrêt . . . . . . . . . . . . . . . .F5

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F6

Entretien et réparations . . . . . . . . . . . . . . . . . . . . . . . . . .F6

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . .F12

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . . . . .F13

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F14

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F15-F16

Liste des pièces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E17

AVERTISSEMENT

LES GAZ D'ÉCHAPPEMENT DU MOTEUR DE CET APPAREIL

CONTIENNENT DES PRODUITS CHIMIQUES CONSIDÉRÉS PAR

L'ÉTAT DE CALIFORNIE COMME POUVANT CAUSER LE

CANCER, DES MALFORMATIONS CONGÉNITALES OU D'AUTRES

EFFETS NOCIFS SUR L'APPAREIL DE REPRODUCTION.

• IMPORTANTES CONSIGNES DE SÉCURITÉ •

LIRE TOUTES LES INSTRUCTIONS

AVANT UTILISATION

• Veuillez lire les instructions avec soin. Familiarisez-vous avec les

commandes et l'utilisation correcte de cet appareil.

• N'utilisez pas l'appareil si vous êtes fatigué, malade ou sous l'effet

de l'alcool, de drogues ou de médicaments.

• Les enfants et adolescents de moins de 15 ans ne doivent pas utiliser

l'appareil exceptés les adolescents assistés d'un adulte.

• Inspectez l'appareil avant utilisation. Remplacez les pièces endommagées.

Regardez s'il y a des fuites de carburant. Assurez-vous que les fixations

sont solidement en place. Remplacez les pièces de l'accessoire de coupe

qui sont fendillées, ébréchées ou endommagées. Assurez-vous que

l'accessoire de coupe est correctement installé et solidement fixé. Assurez-

vous que le protecteur d'accessoire de coupe est correctement fixé et

positionné comme recommandé. Vous risquez sinon de causer des

blessures à l'opérateur et aux spectateurs, et d'endommager l'appareil.

• N'utilisez que du fil de remplacement d’origine du fabricant de 2,03

mm, 0,080 po de diamètre. N'utilisez jamais de fil, de chaîne ou de

cordon à renfort métallique car ils peuvent se briser et se

transformer en projectile dangereux.

• Soyez conscient des risques de blessure à la tête, aux mains et aux

pieds.

• Dégagez la zone de coupe avant chaque usage. Enlevez tous les

objets pouvant être projetés ou happés par l'accessoire de coupe :

cailloux, verre brisé, clous, fil ou ficelle. Éloignez enfants, spectateurs

et animaux de la zone de coupe. Tenez-les à au moins 15 m (50 pi) de

là mais sachez que les spectateurs risquent quand même d'être

atteints par des objets projetés. Les spectateurs doivent porter des

protections oculaires. Arrêtez immédiatement le moteur et

l'accessoire de coupe si quelqu'un s'approche de vous.

• Appuyez sur la manette des gaz et assurez-vous qu'elle revient

automatiquement en position de ralenti. Procédez à tous les

réglages ou réparations avant d'utiliser l'appareil.

AVERTISSEMENTS DE SÉCURITÉ CONCERNANT LES

DÉSHERBEUSES À GAZ

• Ne stockez le carburant que dans des contenants spécialement

conçus et homologués pour le stockage de ce type de matières.

• Arrêtez toujours le moteur et laissez-le refroidir avant de remplir le

réservoir de carburant. N'enlevez jamais le bouchon du réservoir et

n'ajoutez jamais de carburant pendant que le moteur est chaud. Ne

faites jamais fonctionner l'appareil sans que le bouchon de carburant

soit bien mis. Desserrez lentement le bouchon afin de réduire la

pression du réservoir.

• Évitez de créer une source d'allumage pour le carburant déversé. Ne

démarrez pas le moteur avant que les vapeurs de carburant ne se

soient dissipées.

• Ajoutez le carburant dans un endroit bien aéré et propre en plein air

à l'abri des étincelles ou des flammes. N'enlevez lentement le

bouchon du réservoir d'essence qu'après avoir arrêté le moteur. Ne

fumez pas pendant le remplissage de carburant. Essuyez

immédiatement tout déversement de carburant de l'appareil.

• Éloignez l'appareil d'au moins 9.1 m (30 pi) de la source de ravitaillement

en carburant avant de démarrer le moteur. Ne fumez pas et éloignez toute

source d'étincelles ou de flammes vives du lieu de ravitaillement ou de

fonctionnement de l'appareil.

PENDANT L'UTILISATION DE L'APPAREIL

• Évitez de démarrer ou de faire marcher l'appareil à l'intérieur d'une

pièce ou d'un bâtiment fermé. La respiration de fumées

d'échappement peut tuer. Ne faites fonctionner cet appareil qu'à

l'extérieur dans un endroit bien aéré.

• Portez des lunettes de sécurité conformes aux normes ANSI Z87.1

ainsi que des protège-oreilles durant l'utilisation de l'appareil. Portez

un masque facial ou antipoussières si vous travaillez dans un lieu

poussiéreux.

• Portez des pantalons épais et longs, des bottes, des gants et une

chemise à manches longues. Ne marchez pas pieds nus et évitez

les vêtements lâches, bijoux, pantalons courts et sandales. Relevez

les cheveux au-dessus des épaules.

• Le protecteur d'accessoire de coupe doit toujours être en place lors

de l'utilisation de l'appareil. Ne faites pas marcher l'appareil sans

que les deux fils soient bien déployés, en supposant qu'un fil

approprié a été installé. Assurez-vous que le fil ne dépasse pas le

protecteur de sécurité.

• Cet appareil est muni d'un embrayage. L'accessoire de coupe reste

stationnaire lorsque le moteur est au ralenti. Si ce n'est pas le cas,

faites régler l'appareil par un technicien agréé.

• Ajustez la poignée selon votre taille pour mieux l'agripper.

• N'utilisez l'appareil qu'en plein jour ou avec un bon éclairage artificiel.

• Évitez tout démarrage accidentel. Mettez-vous en position de

démarrage chaque fois que vous tirez sur la corde de démarrage.

L'opérateur et l'appareil doivent tous deux être en position stable à

ce moment-là. Voir les Instructions de démarrage et d'arrêt.

• Ne vous étirez pas. Tenez-vous toujours bien sur vos pieds en

position d'équilibre.

• Tenez toujours l'appareil des deux mains lorsque vous le faites

marcher. Agrippez fermement les poignées avant et arrière.

• Gardez les mains, le visage et les pieds éloignés des pièces

mobiles. Ne touchez pas et n'essayez pas d'arrêter l'accessoire de

coupe en rotation.

• Ne touchez pas le moteur, le boîtier d'engrenages ni le silencieux.

Ces pièces deviennent très chaudes à l'utilisation. Elles restent

chaudes brièvement après l'arrêt.

• Servez-vous des outils appropriés. N'utilisez cet outil que pour son

usage prévu.

• Ne faites pas fonctionner le moteur à un régime plus élevé que

nécessaire pour couper, tailler ou faire les bordures. Ne faites pas

tourner le moteur à haut régime si vous ne vous faites pas de coupe.

• Arrêtez toujours le moteur lorsque vous suspendez la coupe ou lorsque

vous vous déplacez d'un lieu de travail vers un autre.

• Si vous heurtez un corps étranger ou que celui-ci est happé, arrêtez le

moteur immédiatement et vérifiez que rien n'a été endommagé. Ne

faites pas fonctionner avant réparation des dommages. Ne faites pas

marcher l'appareil si les pièces sont desserrées ou endommagées.

• Arrêtez et éteignez le moteur dans les cas suivants:

entretien, réparation ou changement d'accessoires ou autres.

• N'utilisez que des pièces de équipement original rechange et

accessoires d’origine du fabricant pour cet appareil. Elles sont

disponibles auprès de votre concessionnaire agréé. L'utilisation de

pièces ou accessoires autres que ceux de éqiupement original peut

causer des blessures graves, endommager l’appareil et annuler sa

garantie.

• Gardez l'appareil exempt d'accumulation de végétation ou autres

matières. Celles-ci peuvent rester logées entre l'accessoire de

coupe et le protecteur.

• Afin de diminuer les risques d'incendie, remplacez tout

silencieux ou pare-étincelles défectueux et conservez le moteur et le

silencieux exempts d'herbe, de feuilles et d'accumulation excessive

de graisse ou de carbone.

AUTRES AVERTISSEMENTS DE SÉCURITÉ

• N'entreposez jamais l'appareil rempli de carburant dans un édifice

où les vapeurs peuvent atteindre une source de flammes vives ou

d'étincelles.

• Laissez le moteur se refroidir avant de l'entreposer ou de le

transporter. Attachez bien l'appareil pendant le transport.

• Rangez l'appareil dans un endroit verrouillé et sec, ou élevé et sec,

hors de portée des enfants, pour éviter une utilisation indésirable ou

un accident.

• Ne trempez et n'arrosez jamais l'appareil avec de l'eau ou tout autre

liquide. Gardez les poignées sèches, propres et exemptes de débris.

Nettoyez après chaque usage. Voir les sections Nettoyage et

Entreposage.

• Conservez ces instructions. Consultez-les souvent et

servez-vous en pour instruire d'autres usagers. Si vous prêtez

l'appareil à quelqu'un, prêtez-lui également ces instructions.

CONSERVER CES INSTRUCTIONS

CONSIGNES DE SÉCURITÉ

AVERTISSEMENT: l'essence est extrêmement

inflammable et ses vapeurs peuvent exploser si on y

met le feu. Veuillez prendre les précautions suivantes.

CONSIGNES DE SÉCURITÉ

SYMBOLES DE SÉCURITÉ ET INTERNATIONAUX

Ce manuel de l'utilisateur décrit les symboles et pictogrammes de sécurité et internationaux pouvant apparaître sur ce produit. Consultez

le manuel de l'utilisateur pour les informations concernant la sécurité, le montage, le fonctionnement, l'entretien et les réparations.

SYMBOLE SIGNIFICATION

• COMMANDE MARCHE/ARRÊT

ALLUMAGE / DÉMARRAGE / MARCHE

• LISEZ LE MANUEL DE L'UTILISATEUR

AVERTISSEMENT - Lisez le manuel de l'utilisateur

et suivez tous les avertissements et consignes de

sécurité. Vous pourriez à défaut entraîner des

blessures graves pour vous ou d'autres personnes.

• COMMANDE MARCHE/ARRÊT

ARRÊT ou STOP

SYMBOLE SIGNIFICATION

• SYMBOLE ALERTE DE SÉCURITÉ

Indique un danger, un avertissement ou une mise

en garde. Ce symbole peut être combiné à d'autres

symboles ou pictogrammes.

• PORTEZ DES PROTECTIONS (YEUX ET OREILLES)

AVERTISSEMENT: les objets projetés et les bruits

forts peuvent endommager la vue et l’ouïe. Portez

une visière de norme ANSI Z87.1-1989 et des

protège-oreilles pendant l'utilisation.

• ÉLOIGNEZ LES SPECTATEURS

AVERTISSEMENT: éloignez tout spectateur, les

enfants et les animaux domestiques en particulier,

d'au moins 15 m (50 pi) de la zone de coupe.

• LES OBJETS PROJETÉS ET LA

TÊTE ROTATIVE

PEUVENT CAUSER DES BLESSURES GRAVES

AVERTISSEMENT: ne faites pas fonctionner sans

protecteur de sécurité en plastique. Tenez-vous à

l'écart de l'accessoire de coupe rotatif.

• AVERTISSEMENT SURFACE CHAUDE

Ne touchez pas un silencieux ou un cylindre

chaud. Vous pourriez vous brûler. Ces pièces

deviennent très chaudes à l'utilisation. Elles restes

chaudes brièvement après l'arrêt.

• CARBURANT SANS PLOMB

Utilisez toujours du carburant sans plomb frais et

propre.

• NIVEAU D'HUILE

Voir le manuel de l'utilisateur pour le type d'huile

approprié.

• LAME AIGUISÉE

AVERTISSEMENT: le protecteur d'accessoire de

coupe comporte une lame aiguisée. Ne touchez

pas la lame pour éviter des blessures graves.

• CONTRÔLE DE L'ÉTRANGLEUR

A. Position d’ÉTRANGLEMENT MAXIMUM

Position d’ÉTRANGLEMENT PARTIEL

C. Position MARCHE.

TYPE D'HUILE RECOMMANDÉ

Il est extrêmement important d'utiliser les bons type et indice d'huile

dans le carter-moteur. Vérifiez l'huile avant chaque utilisation et

changez-la périodiquement. Le fait de ne pas utiliser la bonne huile ou

d'utiliser une huile sale peut entraîner une usure et une défaillance

prématurées du moteur. Utilisez une huile de haute qualité à indice

SAE 30 API (American Petroleum Institute) de type SG, SF, SH.

AJOUT D'HUILE AU CARTER: MISE EN SERVICE

REMARQUE: cet appareil est livré sans huile. Pour éviter

d’endommager l’appareil, mettez de l’huile dans le carter

moteur avant le démarrage.

Votre appareil est livré avec une

bouteille d'huile SAE 30 SF, SG,

SH de 90 ml (3,04 oz) (Fig. 1).

REMARQUE : conservez la

bouteille pour mesurer

correctement la quantité

nécessaire d’huile plus tard.

Voir Changement d'huile.

INFORMATIONS SUR L’HUILE ET LE CARBURANT

AVERTISSEMENT: LE REMPLISSAGE EXCESSIF

DU CARTER-MOTEUR PEUT ANTRAÎNER DES

BLESSURES GRAVES. Nous ne saurions trop insister

sur l'importance de la vérification du niveau d'huile du

carter-moteur et de son maintien. Vérifiez l'huile avant

chaque utilisation et changez-la au besoin tel

qu'indiqué dans la section Changment d'Huile.

1. Dévisser le bouchon de la bouteille d’huile et retirez le

papier couvrant l’ouverture. Replacez le bouchon. Coupez

la pointe de la buse de l’entonnoir (Fig. 1).

2. Placez l'appareil sur une surface horizontale plane.

3. Retirez le bouchon / la jauge d'huile du carter-moteur.

Versez tout le contenu de la bouteille d'huile dans le carter-

moteur (Fig. 2).

4. Versez tout le contenu de la bouteille d'huile dans le carter-

moteur (Fig. 3).

REMARQUE: n’ajoutez jamais

d'huile au carburant ni au

réservoir de carburant.

5. Essuyez toute trace

d'huile déversée et

replacez le bouchon de

remplissage / la jauge.

Nous ne saurions trop insister

sur l'importance de la

vérification du niveau d'huile

du carter-moteur et de son

maintien. Vérifiez l'huile

avant chaque utilisation et

changez-la au besoin tel

qu'indiqué dans la section

Changment d'Huile.

Fig. 1

Buse

d'entonnoir

Fig. 2

Orifice de

remplissage

d’huile

Bouchon de

remplissage /

jauge d'huile

Orifice de

remplissage

d’huile

Fig. 3

Joint

torique

TYPE DE CARBURANT RECOMMANDÉ

En général, si l'appareil ne fonctionne pas correctement, c'est

que le carburant est vieux ou mal mélangé. Prenez soin

d'utiliser du carburant sans plomb frais et propre.

REMARQUE : ceci est un moteur à quatre temps. Pour

éviter d’endommager l’appareil, ne mélangez pas l’huile

avec l’essence.

Définition des carburants mélangés

Les carburants d'aujourd'hui sont souvent un mélange d'essence

et d'oxygénés comme l'éthanol, le méthanol ou l'éther MTBE. Un

carburant mélangé à l'alcool absorbe l'eau. Il suffit de 1% d'eau

pour séparer le carburant et l'huile, ce qui forme de l'acide

pendant l'entreposage. Si vous devez utiliser ce type de

carburant, servez-vous de carburant frais (moins de 60 jours).

Usage de carburants mélangés

Si vous choisissez d'utiliser ou ne pouvez éviter d'utiliser un

carburant mélangé, suivez les conseils suivants :

• Utilisez toujours un mélange de carburant frais selon le

manuel de l'utilisateur.

• Utilisez l'additif STA-BIL

ou un produit équivalent.

• Videz le réservoir et faites marcher le moteur jusqu'à ce qu'il

soit à sec avant d'entreposer l'appareil.

Utilisation d’additifs de carburant

L'utilisation d'additifs de carburant tel que le stabilisant d’essence

STA-BIL

ou un produit équivalent permet d'empêcher la

corrosion et de minimiser la formation de résidus de gomme.

L'usage d'additifs peut empêcher le carburant de former des

dépôts nocifs dans le carburateur pendant six (6) mois maximum.

Ajoutez 23 ml (0,8 oz) d'additif par 4 litres (1 gallon) de carburant

selon les instructions du récipient. N'ajoutez JAMAIS d'additifs

directement dans le réservoir de l'appareil.

AJOUT DE CARBURANT

1. Déposez le bouchon à essence (Fig. 4).

2. Placez le bec du récipient d’essence dans l’orifice du

réservoir (Fig. 19) et remplissez celui-ci.

REMARQUE : Ne

remplissez pas trop le

réservoir.

3. Essuyez tout

déversement d’essence.

4. Remettez le bouchon

du réservoir.

5. Éloignez l'appareil d'au

moins 9,1 m (30 pi) de

la source et du site de

ravitaillement en

carburant avant de

démarrer le moteur.

REMARQUE : Éliminez le vieux carburant conformément aux

règlements fédéral, provincial et municipal en vigueur.

INFORMATIONS SUR L’HUILE ET LE CARBURANT

AVERTISSEMENT: Ajoutez du carburant dans

un lieu propre et bien aéré en plein air. Essuyez

immédiatement tout déversement de carburant.

Évitez de mettre le feu au carburant déversé. Ne

démarrez pas le moteur avant dissipation des

vapeurs de carburant.

AVERTISSEMENT: L'essence est extrêmement

inflammable et les vapeurs qui s'en dégagent

peuvent exploser si on y met le feu. Arrêtez toujours

le moteur et laissez-le refroidir avant de remplir le

réservoir. Ne fumez pas en remplissant le réservoir.

Éloignez toute source d'étincelles ou de flammes

vives de la zone.

AVERTISSEMENT: Enlevez le bouchon du

réservoir lentement pour ne pas être blessé par

les jets d'essence. Ne faites pas marcher

l'appareil sans que le bouchon soit bien mis.

Protecteur

d'accessoire

de coupe

Bouchon

carburant

Manette

des gaz

Poignée en D

Accessoire

de coupe

Prise de l'arbre

Poire

d'amorçage

Bouchon de remplissage

/ jauge d'huile

Levier

d'étrangleur

Bougie

Boîtier

d'engrenages

Poignée de la corde de démarrage

Lame

coupante

Bougie

Silencieux

Protection du silencieux

Pare-Étincelles

Commande

Marche/Arrêt

FAMILIARISEZ-VOUS AVEC L’APPAREIL

Couvercle

du filtre à

air

INSTALLATION ET RÉGLAGE DE LA POIGNÉE EN D

1. Enfoncez la poignée en D sur le corps de l'arbre afin de

l’incliner vers la prise de l'arbre (Fig. 5). Le trou de boulon

carré de la poignée se trouve à droite.

2. Insérez le boulon à épaulement dans le trou carré de la

poignée et enfoncez-le complètement. Sur le côté gauche

de la poignée, placez la rondelle sur ce boulon, puis vissez

l'écrou papillon sur le boulon. Ne serrez pas avant de régler

le guidon.

3. Tournez la poignée

en D afin que la

prise soit sur le

dessus du corps de

l'arbre. Placez-la à

au moins 15,24 cm

(6 po) de l’extrémité

de la prise de

l'arbre.

4. Tenez l'appareil en

position d’utilisation,

puis positionnez la poignée en D de manière à assurer une

prise idéale.

5. Serrez l'écrou papillon jusqu'à bien fixer la poignée en D.

INSTRUCTIONS DE MONTAGE

Fig. 4

Bouchon du

carburant

Réservoir

Bec du récipient

d'essence

Carburant

sans plomb

Fig. 5

Boulon

Rondelle

Écrou

papillon

Serrez

Poignée de

l'arbre

Poignée en D

15,24 cm

(6 po)

minimum

Corps de

l'arbre

La page charge ...

Troy-Bilt Trimmer TB26CO Manuel utilisateur

Marque: Troy-Bilt

Modèle: Trimmer TB26CO

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

TB26CO

Télécharger le PDF

rapport

dans d''autres langues

English: Troy-Bilt Trimmer TB26CO User manual
español: Troy-Bilt Trimmer TB26CO Manual de usuario

Autres documents

Comunello 87PSQ Manuel utilisateur