JVC KS-DR1004D Manuel utilisateur

Marque: JVC

Modèle: KS-DR1004D

Catégorie: Amplificateurs audio de voiture

Taper: Manuel utilisateur

KS-DR1004D

COMPACT 4 CHANNEL AMPLIFIER

INSTRUCTION MANUAL

AMPLIFICATEUR COMPACT 4 CANAUX

MODE D’EMPLOI

AMPLIFICADOR COMPACTO DE CUATRO CANALES

MANUAL DE INSTRUCCIONES

Accessories / Accessoires / Accesorios

1.5 m (5 ft)

DC cable

Câble CC

Cable CC 1

350 mm (13-3/4”)

Wire band

Serre-câble

Atadura de cables 2

1 m (3.3 ft)

RCA cable

Câble RCA

Cable RCA 2

100 mm (3-15/16”)

Wire band

Serre-câble

Atadura de cables 2

Ø4×16 mm

Self-tapping screws

Vis taraudeuses

Tornillo autorroscantes 4Protective cover

Couvercle de protection

Cubierta protectora 2

COMPACT 4-CHANNEL AMPLIFIER

KS-DR1004D

MAX POWER

157 mm (6-3/16”)

169 mm (5-5/8”)

45 mm (1-3/4”)

145 mm (5-11/16”)

99 mm (3-7/8”)

76 mm (3”)

Dimensions / Dimensions / Dimensiones

Specifications

Speci cations subject to change without notice.

Audio section

Max power output .............................................................................400 W

Rated power output (+B = 14.4 V)

Stereo (2 Ω) .....................................45 W × 4 (1 kHz, ≤ 1.0% THD)

Bridged (4 Ω) ..................................90 W × 2 (1 kHz, ≤ 1.0% THD)

Speaker impedance .............................4 Ω (2 Ω to 8 Ω allowable)

(Bridged connection: 4 Ω to 8 Ω allowable)

Frequency response (+0, −1 dB) ..............................20 Hz–20 kHz

Input sensitivity (RCA)............................................................0.2 V–5.0 V

Signal to noise ratio............................................................................98 dB

Input impedance ................................................................................ 10 kΩ

Low pass  lter frequency (−12 dB / oct.)

....................................................................50 Hz–200 Hz (variable)

High pass  lter frequency (−12 dB / oct.)

....................................................................50 Hz–200 Hz (variable)

General

Operating voltage ................................................12 V DC car battery

Current consumption ......................................................................... 15 A

Dimensions (W × H × D) ........................................145 × 45 × 99 mm

5-11/16 × 1-3/4 × 3-7/8 inch

Weight .....................................................................................0.7 kg (1.5 lbs)

45 Watts RMS × 4 at 4 Ohms and ≤ 1%

THD+N

82 dBA (Reference: 1 Watt into 4 Ohms)

Safety precautions

WARNING

To prevent injury or  re, take the following precau-

tions:

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and

wiring work to professionals.

• To prevent a short circuit, never put or leave any metal-

lic objects (such as coins or metal tools) inside the unit.

• If the unit starts to emit smoke or strange smells, turn

o the power immediately and consult your JVC dealer.

• Do not touch the unit during use because the sur-

face of the unit becomes hot and may cause burns if

touched.

CAUTION

To prevent damage to the machine, take the follow-

ing precautions:

• Be sure the unit is connected to a 12 V DC power sup-

ply with a negative ground connection.

• Do not open the top or bottom covers of the unit.

• Do not install the unit in a spot exposed to direct

sunlight or excessive heat or humidity. Also avoid

places with too much dust or the possibility of water

splashing.

• When replacing a fuse, only use a new one with the

prescribed rating. Using a fuse with the wrong rating

may cause your unit to malfunction.

• To prevent a short circuit when replacing a fuse,  rst

disconnect the wiring harness.

NOTE

• If you experience problems during installation, consult

your JVC dealer.

• If the unit does not seem to be working right, consult

your JVC dealer.

Cleaning the unit

If the front panel gets dirty, turn o the power and wipe

the panel with a dry silicon cloth or soft cloth.

CAUTION

Do not wipe the panel with a hard cloth or a cloth damp-

ened by volatile solvents such as paint thinner and alco-

hol. They can scratch the surface of the panel and / or

cause the indicator letters to peel o .

To prevent battery rise

When the unit is used in the ACC ON position without

turning the engine ON, it depletes the battery. Use it after

starting the engine.

Protection function

The protection function is activated in the following

situations:

This unit is equipped with a protection function for

protecting this unit and your speakers from various acci-

dents or problems that can occur.

When the protection function is triggered, the ampli er

stops operating.

• When a speaker wire may be short-circuited.

• When a speaker output contacts ground.

• When the unit malfunctions and a DC signal is sent to

the speaker output.

• When the internal temperature is high and unit won’t

operate.

• When detects a low impedance at the speaker

connections.

Wiring

• If a buzzing noise is heard from the speakers when the

engine is running, connect a line noise  lter (optional)

to each of the battery wire.

• Do not allow the wire to directly contact the edge of

the iron plate by using Grommets.

• Connect the ground wire to a metal part of the car

chassis that acts as an electrical ground passing elec-

tricity to the battery‘s negative terminal. Do not turn

the power on if the ground wire is not connected.

• Be sure to install a protective fuse in the power cord

near the battery. The protective fuse should be the

same capacity as the unit’s fuse capacity or somewhat

larger.

• When more than one power ampli er are going to be

used, use a power supply wiring wire and protective

fuse of greater current-handling capacity than the total

maximum current drawn by each ampli er.

Speaker selection

• Using speakers with smaller input ratings than the

ampli er’s output power would result in smoke gener-

ation or equipment failure.

• The impedance of the speakers that are going to be

connected should be 2 Ω or greater (for stereo con-

nections), or 4 Ω or greater (for bridged connections).

When more than one set of speakers are going to be

used, calculate the combined impedance of the speak-

ers and then connect suitable speakers to the ampli er.

Combined

impedance

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.

Before calling service,  rst check the following table for possible problems.

PROBLEM POSSIBLE CAUSE SOLUTION

No sound.

(No sound from one

side.)

(Blown fuse.)

• Input (or output) cables are disconnected.

• Protection circuit may be activated.

• Volume is too high.

• The speaker cord is shorted.

• Connect the input (or output) cables.

• Check connections by referring to “Protection

function”.

• Replace the fuse and use lower volume.

• After check the speaker cord and  xing the

cause of the short, replace the fuse.

The output level is too

small (or too large). • The input sensitivity adjusting control is not

set to the correct position.

• Adjust the control correctly referring to “Con-

trols”.

The sound quality is

bad.

(The sound is

distorted.)

• The speakers wire are connected with

wrong / polarity.

• A speaker wire is pinched by a screw in the

car body.

• The switches may be set improperly.

• Connect them properly checking the /

of the terminals and wires well.

• Connect the speaker wire again so that it is

not pinched by anything.

• Set switches properly by referring to “Con-

trols”.

Guide de dépannage

Ce qui peut apparaître comme un mauvais fonctionnement de votre appareil n’est peut-être que le résultat

d’une mauvaise opération ou d’une mauvaise connexion. Avant d’appeler un centre de service, véri ez d’abord

dans le tableau suivant les problèmes possibles.

PROBLEME CAUSE POSSIBLE SOLUTION

Absence de sons.

(Pas de son d’un côté)

(Fusible grillé)

• Les câbles d’entrée (ou de sortie) sont

débranchés.

• Le circuit de protection peut être

actionné.

• Le volume est trop fort.

• Les  ls de raccordement d’enceinte sont

en court-circuit.

• Brancher les câbles d’entrée (ou de sortie).

• Véri er les raccordements en se reportant au

paragraphe «Fonction de protection».

• Remplacez le fusible et utilisez un niveau de

volume plus faible.

• Après avoir véri é le câble d’enceinte et réparé

la cause du court-circuit, remplacez le fusible.

Niveau de sortie trop

faible (ou trop fort). •

La commande de réglage de la sensibilité d’en-

trée n’est pas amenée sur la bonne position.

• Faire le réglage correctement en se reportant

aux indications données en «Contrôles».

La qualité sonore est

mauvaise.

(Le son est distordu.)

• Les câbles de haut-parleur ont été raccor-

dés en inversant la polarité / .

• Un câble de haut-parleur est pincé par

une vis dans le châssis de la voiture.

• Les commutateurs ne sont peut-être pas

positionnés comme il convient.

• Raccorder correctement en respectant les indi-

cations et des bornes et des câbles.

• Rebrancher le câble de haut-parleur en évitant

tout pincement

• Positionner les commutateurs en tenant

compte des indications fournies aux para-

graphes «Contrôles».

Guía sobre localización de averías

Lo que podría parecer una falla de funcionamiento de su unidad podría ser simplemente el resultado de un

pequeño error de operación o de un defecto de conexión. Antes de acudir al servicio, veri que primero el

siguiente cuadro sobre los problemas que se podrían presentar.

PROBLEMA CAUSA POSIBLE SOLUCION

No hay sonido.

(No hay sonido de un

lado.)

(Fusible fundido)

• Los cables de entrada (o salida) están des-

conectados.

• El circuito de protección puede estar acti-

vado.

• El volumen está demasiado alto.

• El cable del altavoz está cortocircuitado.

• Conecte los cables de entrada (o salida).

• Compruebe las conexiones consultando “Fun-

ción de protección”.

• Reemplace el fusible y utilice volumen bajo.

• Después de revisar el cable del altavoz y arreglar

la causa del cortocircuito, reemplace el fusible.

El nivel de salida está

muy bajo (o muy alto) • El control de ajuste de sensibilidad de

entrada no está en la posición correcta.

• Ajuste bien el control consultando en “Contro-

les”.

La calidad del sonido

es mala.

(El sonido está

distorsionado.)

• Los cables de los altavoces están conecta-

dos con las polaridades / invertidas.

• Un cable de altavoz está pellizcado por

un tornillo de la carrocería del automóvil.

• Los conmutadores pueden estar mal ajus-

tados.

• Conéctelos correctamente asegurándose bien

de cuáles son los terminales y .

• Vuelva a conectar los cables de los altavoces de

forma que no queden pellizcados.

• Ponga bien los conmutadores consultando

“Controles”.

For U.S.A.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modi cations to this equipment may cause

harmful interference unless the modi cations are expressly approved in the instruction manual. The user could lose the

authority to operate this equipment if an unauthorized change or modi cation is made.

FCC NOTE

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment may cause harmful

interference to radio communications, if it is not installed

and used in accordance with the instructions. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harm-

ful interference to radio or television reception, which can

be determined by turning the equipment o and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician

for help.

Supplier’s Declaration of Conformity

Trade Name: JVC

Products: COMPACT 4 CHANNEL AMPLIFIER

Model Name: KS-DR1004D

Responsible Party: JVCKENWOOD USA CORPORATION

2201 East Dominguez Street,

Long Beach, CA 90810, U.S.A.

PHONE: 310 639-9000

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC

RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

For Argentina

Información acerca de la eliminación de

equipos eléctricos y electrónicos al final

de la vida útil (aplicable a los países que

hayan adoptado sistemas independientes

de recogida de residuos)

Los productos con el símbolo de un contenedor con rue-

das tachado no podrán ser desechados como residuos

domésticos.

Los equipos eléctricos y electrónicos al  nal de la vida útil,

deberán ser reciclados en instalaciones que puedan dar el

tratamiento adecuado a estos productos y a sus subpro-

ductos residuales correspondientes. Póngase en contacto

con su administración local para obtener información sobre

el punto de recogida más cercano. Un tratamiento correcto

del reciclaje y la eliminación de residuos ayuda a conservar

los recursos y evita al mismo tiempo efectos perjudiciales

en la salud y el medio ambiente.

CAUTION

• Do not install in the below locations;

(Unstable location, In a location that interferes with driving, In a location

that gets wet, In a dusty location, In a place that gets hot, In a place that

gets direct sunlight, In a location that gets hit by hot air)

• Do not install the unit under the carpet. Otherwise heat build-up occurs

and the unit may be damaged.

• Install this unit in a location which allows heat to easily dissipate. Once

installed, do not place any object on top of the unit.

• The surface temperature of the ampli er will become hot during use.

Install the ampli er in a place where people, resins, and other substances

that are sensitive to heat will not come into contact with it.

• When making a hole under a seat, inside the trunk, or somewhere else in

the vehicle, check that there is nothing hazardous on the opposite side

such as a gasoline tank, brake pipe, or wiring harness, and be careful not

to cause scratches or other damage.

• Do not install near the dashboard, rear tray, or air bag safety parts.

• The installation to the vehicle should securely fasten the unit to a place in

which it will not obstruct driving. If the unit comes o due to a shock and

hits a person or safety part, it may cause injury or an accident.

• After installing the unit, check to make sure that electrical equipment

such as the brake lamps, turn signal lamps and windshield wipers oper-

ate normally.

Installation procedure

Read the instruction manual well to select the proper connection and

setting.

1. Remove the ignition key and disconnect the negative terminal of

the battery to prevent short circuits.

2. There are two options:

* Refer to “Connection” as below.

Type A: RCA INPUT connection

A-1 Connect the battery wire.

A-2 Connect the ground wire to chassis ground of vehicle.

A-3 Connect the power control wire.

A-4 Connect the speakers.

A-5 Connect the DC cable into the connector at KS-DR1004D.

A-6 Connect the RCA cable.

Type B: SPEAKER INPUT connection

B-1 Connect the battery wire.

B-2 Connect the ground wire to chassis ground of vehicle.

B-3 Connect the speakers.

B-4 Connect the DC cable into the connector at KS-DR1004D.

B-5 Cut off the RCA cable, then connect the correct corresponding

speaker output from the FACTORY INSTALLED HEAD UNIT directly.

3. Attach the unit.

4. Connect the negative terminal of the battery.

Installation / Installation / Instalación

Installation board, etc. (thickness: 15 mm or more)

Tableau d’installation, etc. (épaisseur: 15 mm ou plus)

Tablero de instalación, etc. (grosor: 15 mm o más)

Example A: using the screws

Exemple A: utilisation des vis

Ejemplo A: utilizando los tornillos

Example B: using the wire bands

Exemple B: utilisation des serre-câbles

Ejemplo B: utilizando los atadura de cables

Parts included

Pièces comprises

Partes incluidas

Parts included

Pièces comprises

Partes incluidas

(350 mm (13-3/4”))

Protective cover / Couvercle de protection / Cubierta protectora

Spare

De rechange

Repuesto

MOISTURE

HUMIDITÉ

HUMEDAD

DUST

POUSSIÈRE

POLVO

After setting up the unit, put the protective

cover on the control panel.

Après avoir con guré l’unité, placez le couvercle

de protection sur le panneau de commande.

Después de con gurar la unidad, coloque la

cubierta protectora sobre el panel de control.

HEAD UNIT

[Purple/Black] [Violet/Noir] [Purpúreo/Negro]

[Gray/Black] [Gris/Noir] [Gris/Negro]

[White] [Blanc] [Blanco]

[White/Black] [Blanc/Noir] [Blanco/Negro]

[Gray] [Gris] [Gris]

[Gray/Black] [Gris/Noir] [Gris/Negro]

[Green] [Vert] [Verde]

[Green/Black] [Vert/Noir] [Verde/Negro]

[Purple] [Violet] [Purpúreo]

[Purple/Black] [Violet/Noir] [Purpúreo/Negro]

[White] [Blanc] [Blanco]

[White/Black] [Blanc/Noir] [Blanco/Negro]

[Green/Black] [Vert/Noir] [Verde/Negro]

[Green] [Vert] [Verde]

[Gray] [Gris] [Gris]

[Purple] [Violet] [Purpúreo]

[Purple/Black] [Violet/Noir] [Purpúreo/Negro]

[White] [Blanc] [Blanco]

[White/Black] [Blanc/Noir] [Blanco/Negro]

[Gray] [Gris] [Gris]

[Gray/Black] [Gris/Noir] [Gris/Negro]

[Green] [Vert] [Verde]

[Green/Black] [Vert/Noir] [Verde/Negro]

[Purple] [Violet] [Purpúreo]

Prevent a short circuit!

Éviter les court-circuits !

¡ Evitar cortocircuitos !

Prevent a short circuit!

Éviter les court-circuits !

¡ Evitar cortocircuitos !

A.ch

B.ch

A.ch

B.ch

A.ch

B.ch

A.ch

System examples / Exemple de configuration / Ejemplos del sistema

4-channel system / Système 4 voies / Sistema de 4 canales

High-power 2-channel system / Système 2 voies, puissance élevée / Sistema de 2 canales de alta potencia

2-channel + Subwoofer system / Système 2 voies + enceinte d’extrêmes graves /

Sistema de 2 canales + Altavoz de subgraves

Front left speaker

Haut-parleur avant gauche

Altavoz delantero izquierdo

Front right speaker

Haut-parleur avant droit

Altavoz delantero derecho

Rear left speaker

Haut-parleur arrière gauche

Altavoz trasero izquierdo

Rear right speaker

Haut-parleur arrière droit

Altavoz trasero derecho

Left speaker (Bridged)

Haut-parleur gauche (Pont)

Altavoz izquierdo (Puenteada)

Right speaker (Bridged)

Haut-parleur droit (Pont)

Altavoz derecho (Puenteada)

Left speaker (high pass)

Haut-parleur gauche ( ltre passe-haut)

Altavoz izquierdo (paso alto)

Right speaker (High pass)

Haut-parleur droit ( ltre passe-haut)

Altavoz derecho (paso alto)

Subwoofer (Bridged)

Haut-parleur d’extrêmes graves (Pont)

Altavoz de subgraves (Puentead)

[RCA Y cable] [Y Câble RCA]

[Y Cable RCA]

COMPACT 4-CHANNEL AMPLIFIER

KS-DR1004D

MAX POWER

FRONT

REAR

Type A: RCA INPUT connection

Type A: Raccordement RCA INPUT

Tipo A: Conexión RCA INPUT

Type B: SPEAKER INPUT connection

Type B: Raccordement SPEAKER INPUT

Tipo B: Conexión SPEAKER INPUT

White

Blanc

Blanco

White/Black

Blanc/Noir

Blanco/Negro

Gray

Gris

Gray/Black

Gris/Noir

Gris/Negro

Green

Vert

Verde

Green/Black

Vert/Noir

Verde/Negro

Purple

Violet

Purpúreo

Purple/Black

Violet/Noir

Purpúreo/Negro

Car fuse box

Boîte de fusible

Caja de fusibles

del automóvil Battery

Batterie

Batería

FACTORY INSTALLED

HEAD UNIT

SPEAKER OUTPUT

R-FRONT-LR-REAR-L

AFTER MARKET

HEAD UNIT

FRONT

REAR

Battery wire (Yellow) / Câble de la batterie (Jaune) / Cable de la batería (Amarillo)

BATT

ACC

Power control wire (Blue); for “RCA INPUT connection”

Câble de commande de l’alimentation (Bleu); pour «Raccordement RCA INPUT»

Cable de control de alimentación (Azul); para “Conexión RCA INPUT”

* 1

Ground wire (Black)

Câble de masse (Noir)

Cable de masa (Negro)

* 1

The output from the FACTORY INSTALLED HEAD

UNIT up to 50 W can be input. The power is turned

on and o as the unit detects input signal (SIGNAL

SENSING TURN-ON). Therefore it is not necessary to

connect the power control wire.

La puissance de sortie maximum de la FACTORY

INSTALLED HEAD UNIT ne doit pas dépasser 50 W.

L’alimentation est activée et désactivée lorsque l’ap-

pareil détecte le signal d’entrée (SIGNAL SENSING

TURN-ON). C’est pourquoi il n’est pas nécessaire de

connecter le câble de commande de l’alimentation.

El FACTORY INSTALLED HEAD UNIT deberá tener

una potencia de salida máxima no superior a 50

W. La alimentación se enciende y apaga conforme

la unidad detecte una señal de entrada (SIGNAL

SENSING TURN-ON). Por lo tanto no es necesario

conectar el cable de control de alimentación.

Connection / Raccordements / Conexiones

WARNING Remove the ignition key and disconnect the negative terminal of the battery to prevent short circuits.

AVERTISSEMENT Retirer la clé de contact et débrancher la borne négative de la batterie pour éviter les court-circuits.

ADVERTENCIA

Retire la llave de encendido y desconecte el terminal negativo de la batería para evitar cortocircuitos.

In a computer-equipped vehicle, when you remove the terminal of the battery, the memory may disappear, or a defect may occur in the electrical system of the vehicle. Consult your dealer for further details.

Dans un véhicule équipé d’un ordinateur, lorsque vous retirez la borne de la batterie, la mémoire peut disparaître ou un défaut peut se produire dans le système électrique du véhicule. Consultez votre revendeur pour de plus amples détails.

En un vehículo equipado con ordenador, cuando extrae el terminal de la batería, la memoria puede desaparecer o puede producirse un defecto en el sistema eléctrico del vehículo. Consulte a su proveedor para obtener más detalles.

Fuse (15 A)

NOTE

If you can’t  nd the speci ed capacity

fuse at your store etc., consult your JVC

dealer.

Fusible (15 A)

REMARQUE

Si vous ne trouvez pas de fusible de

calibre adéquat dans le commerce,

etc., contacter votre agent JVC.

Fusible (15 A)

NOTA

Si no puede encontrar el fusible de la

capacidad especi cada en su almacén

etc., consulte su distribuidor JVC.

Prevent a short circuit !

Éviter les court-circuits !

¡ Evitar cortocircuitos !

A-1

A-3

A-6

B-5

B-1

A-2

A-4

B-2

B-3

A-5 B-4

Parts included

Pièces comprises

Partes incluidas

Parts included

Pièces comprises

Partes incluidas

Parts included

Pièces comprises

Partes incluidas

(100 mm (3-15/16”))

WARNING

Particular attention must be given

to making good electrical contact

at the amplifier-output and speaker

terminals.

Poor or loose connections can cause

sparking or burning at the terminals

because of the very high power that

the ampli er can deliver.

CAUTION

• If sound is not output normally,

immediately turn power off and

check connections.

• Be sure to turn the power o before

changing the setting of any switch.

• If the fuse blows, check wires for

shorts, then replace the fuse with one

of the same rating.

• Check that no unconnected wires

or connectors are touching the car

body. Do not remove caps from

unconnected wires or connectors to

prevent short circuits.

• Connect the speaker wires to appro-

priate speaker connectors separately.

Sharing the negative wire of the

speaker or grounding speaker wires

to the metal body of the car can

cause this unit to fail.

• After installation, check that the brake

lamps, turn signal lamps and wind-

shield wipers work properly.

AVERTISSEMENT

Veillez à ce que le contact électrique à

la sortie de l’ampli cateur et aux prises

des enceintes soit bien établi.

Un mauvais branchement ou un bran-

chement lâche peut causer des étin-

celles ou un réchau ement des prises

du fait de la très grande puissance de

l’ampli cateur.

ATTENTION

• En cas d’anomalie, mettre immé-

diatement l’appareil hors tension et

véri er tous les raccordements.

• Veiller à mettre l’appareil hors ten-

sion avant de changer la position

des commutateurs.

• Si le fusible saute, vérifier si les

câbles ne sont pas court-circuités,

et remplacer le fusible par un autre

fusible de même capacité nominale.

•

Vérifier qu’aucun câble ou connec-

teur non raccordé ne touche la car-

rosserie de la voiture. Ne pas retirer

les capuchons des câbles ou connec-

teurs non raccordés a n d’éviter tout

courtcircuit.

• Raccorder séparément les câbles

de haut-parleur aux connecteurs de

haut-parleur appropriés. La mise en

commun du câble négatif d’un haut-

parleur ou des  ls de masse des haut-

parleurs à la carrosserie métallique de

la voiture pourrait rendre l’appareil

inopérant.

• Après l’installation, vérifier que les

voyants de frein, les clignotants

et les essuie-glace fonctionnent

correctement.

ADVERTENCIA

Debe ponerse especial atención para

que se haga un buen contacto eléc-

trico en la salida del ampli cador y en

los terminales de los altavoces.

Las conexiones mal hechas o las cone-

xiones  ojas pueden causar chispas o

quemaduras en los terminales debido

a la potencia muy alta que puede

suministrar el ampli cador.

PRECAUCIÓN

• Si el sonido no sale normalmente,

desconecte inmediatamente la

alimentación y compruebe las

conexiones.

• No se olvide de desconectar la ali-

mentación antes de cambiar el ajuste

de cualquier conmutador.

• Si el fusible se quema, compruebe

que no haya un cortocircuito en los

cables, luego cambie el fusible por

uno que tenga el mismo amperaje.

•

Veri que que ninguno de los cables

o conectores que están sin conectar

se encuentren tocando la carrocería

del automóvil. No retire las tapas de

los cables o conectores que están sin

conectar para evitar de que se pro-

duzcan cortocircuitos.

• Conecte los cables del altavoz a los

conectores adecuados del altavoz

separadamente. La puesta en con-

tacto de terminales de altavoces dis-

tintos, o la conexión como toma de

tierra de los terminales del altavoz al

coche del automóvil, pueden causar

daños a la unidad.

•

Después de la instalación, compruebe

que las lámparas del freno, luces de

destello y limpiaparabrisas funcionar

correctamente.

Controls / Contrôles / Controles

This is a 4 channel amplifier in-

cluding 2 stereo amplifiers in a

body. One ampli er is referred to

as ampli er A and the other is am-

plifier B. This unit is compatible

with a large variety of systems by

combining the switches and func-

tions described in the following.

FILTER FREQUENCY control

(A.ch / B.ch)

Sets the cutoff frequency when the

“FILTER” switch is set to “HPF” or “LPF”.

FILTER switch (A.ch / B.ch)

This switch allows to apply high-pass

or low-pass filtering to the speaker

outputs.

• HPF (High-Pass Filter) position:

The  lter outputs the band of higher

frequencies than the frequency set

with the “FILTER FREQUENCY” control.

• OFF position:

The entire bandwidth is output with-

out  ltering.

• LPF (Low-Pass Filter) position:

The  lter outputs the band of lower

frequencies than the frequency set

with the “FILTER FREQUENCY” control.

LINE IN terminal (A.ch / B.ch)

INPUT SENSITIVITY control

(A.ch / B.ch)

Set this control according to the

pre-output level of the HEAD UNIT

connected with this unit.

NOTE

For the pre-output level, refer to the

“Specifications” in the instruction

manual of the HEAD UNIT.

Ceci est un amplificateur à 4

canaux avec deux amplificateurs

stéréophoniques en un élément;

l’un appelé Amplificateur A,

l’autre Ampli cateur B. Cet appa-

reil est compatible avec diverses

con gurations de chaîne, simple-

ment en sélectionnant les posi-

tions des commutateurs et les

fonctions comme indiqué ci-après.

Commande FILTER FREQUENCY

(A.ch / B.ch)

Cette commande permet de préci-

ser la fréquence de coupure quand

le commutateur «FILTER» est sur la

position «HPF» ou «LPF».

Commutateur FILTER

(A.ch / B.ch)

Ce commutateur permet d’effectuer

un  ltrage des graves, ou des aigus,

appliqués vers les haut-parleurs.

• Position HPF (Filtre passe-haut):

Le filtre laisse passer les fréquences

supérieures à la fréquence précisée

au moyen de la commande «FILTER

FREQUENCY».

• Position OFF:

Le  ltre n’agit pas, autrement dit tout

le spectre des fréquences est présent

en sortie.

• Position LPF (Filtre passe-bas):

Le filtre laisse passer les fréquences

inférieures à la fréquence précisée

au moyen de la commande «FILTER

FREQUENCY».

Borne LINE IN (entrée de ligne)

(A.ch / B.ch)

Commande INPUT SENSITIVITY

(sensibilité d’entrée) (A.ch / B.ch)

Régler cette commande selon le

niveau de pré-sortie de la HEAD UNIT

branché à cet ampli cateur.

REMARQUE

Se référer à la section «Spéci cations»

du manuel des instructions de la

HEAD UNIT à propos du niveau de

pré-sortie.

Este es un ampli cador de 4 cana-

les con dos amplificadores esté-

reo en un mismo cuerpo. Uno de

los ampli cadores recibe el nom-

bre ampli cador A y el otro el de

amplificador B. Combinando los

conmutadores y las funciones des-

critas a continuación, esta unidad

amplificadora es compatible con

una amplia gama de sistemas.

Control FILTER FREQUENCY

(A.ch / B.ch)

Ajusta la frecuencia de corte cuando

el conmutador “FILTER” está en “HPF”

o “LPF”.

Conmutador FILTER (A.ch / B.ch)

Este conmutador permite aplicar la

 ltración de paso alto o paso bajo a

las salidas de los altavoces.

• Posición HPF ( ltro de paso alto):

El filtro da salida a la banda de fre-

cuencias más altas que la frecuen-

cia ajustada con el control “FILTER

FREQUENCY”.

• Posición OFF:

Todo el ancho de banda sale sin

 ltración.

• Posición LPF ( ltro de paso bajo):

El filtro da salida a la banda de fre-

cuencias más bajas que la frecuen-

cia ajustada con el control “FILTER

FREQUENCY”.

Terminal LINE IN (entrada de

linea) (A.ch / B.ch)

Control INPUT SENSITIVITY

(sensibilidad de entrada)

(A.ch / B.ch)

Ajustar este control de acuerdo con

el nível de presalida de la HEAD UNIT

conectada a este ampli cador.

NOTA

Referir a “Especi caciones” del manual

de instrucciones de la HEAD UNIT con

respecto al nível de presalida.

U.S.A.

JVCKENWOOD

USA

Cor

oration

TO OUR VALUED CUSTOMER

THANK YOU FOR PURCHASING THIS JVC PRODUCT.

WE WANT

HELP YOU ACHIEVE A PERFECT EXPERIENCE.

NEED HELP ON

HOW

HOOK

UP?

NEED ASSISTANCE ON

HOW

OPERATE?

NEED

LOCATE A

JVC

SERVICE CENTER?

PURCHASE ACCESSORIES?

JVC IS HERE TO HELP!

TOLL FREE: 1 (800)252-5722

http://www.us.jvckenwood.com

Remember to retain your Bill of Sale for Warranty Service.

Do not attempt to service the product yourself

Caution

prevent electrical shock, do not open the cabinet.

There are

user serviceable parts inside.

Please refer to qualified service personnel for repairs.

PRODUCT REGISTRATION

We suggest that you register your product since it will enable us to contact you

directly if it is ever necessary to correct a safety related condition in your product.

You

can register at http://www.us.jvckenwood.com

Please note that failure to register does not diminish any of your rights during the

warranty period.

BT-50004-1

(15/11)

JVC

LIMITED

WARRANTY

ONLY

FOR

PRODUCT

PURCHASED

U.S

.A.

JVCKENWOOD

USA

Corporation

warrants

this

product

and

all

parts

thereof

except

set

forth

below

ONLY

THE

ORIGINAL

RETAIL

PURCHASER

FREE

FROM

DEFECTIVE

MATERIALS

AND

WORKMANSHIP

from

the

date

original

purchase

for

the

period

shown

below

("The

Warranty

Period")

PARTS

YRS

LABOR

YRS

Car

audio

ARSENAL

series

PARTS

1 YR/

LABOR

All

other

car

audio

products

THIS

LIMITED

WARRANTY

VALID

ONLY

THE

FIFTY

(50)

UNITED

STATES,

THE

DISTRICT

COLUMBIA

AND

THE

COMMONWEALTH

PUERTO

RICO.

WHAT

WILL

DO:

this

product

found

defective

within

the

warranty

per

iod,

JVC

will

repair

replace

defective

parts

with

new

rebuilt

equivalents

charge

the

original

owner.

Such

repair

and

replacement

services

shall

rendered

JVC

during

normal

business

hours

JVC

authorized

service

centers.

Parts

used

for

replacement

are

warranted

only

for

the

remainder

the

Warranty

Period.

All

products

may

brought

JVC

authorized

service

center

carry-in

basis.

WHAT

YOU

MUST

FOR

WARRANTY

SERVICE:

Please

not

return

your

product

the

retailer.

Instead

return

your

product

the

JVC

authorized

service

center

nearest

you.

shipping

the

product

the

service

center,

please

sure

package

carefully,

preferably

the

original

packaging,

and

include

brief

description

the

problem(s)

and

copy

the

proof

purchase

verify

purchase

date.

Please

call

-800-252-5722

locate

the

nearest

JVC

authorized

service

center.

Service

locations

can

also

obtained

from

our

website

http://www.us.jvckenwood.com.

you

have

any

questions

concerning

your

JVC

Product,

please

contact

our

Customer

Care

Center

800-252-5722

WHAT

NOT

COVERED

This

limited

warranty

provided

JVC

does

not

cover:

Products

which

have

been

subject

abuse,

accident,

alteration,

modification,

tampering,

negligence,

misuse,

faulty

installation,

lack

reasonable

care,

repaired

serviced

anyone

other

than

service

facility

authorized

JVC

render

such

service,

affixed

any

attachment

not

provided

with

the

products,

the

model

serial

number

has

been

altered,

tampered

with,

defaced

removed

Initial

installation,

installation

and

removal

from

cabinets

mounting

systems.

Operational

adjustments

covered

the

Owner's

Manual

normal

maintenance,

video

and

audio

head

cleaning:

Damage

that

occurs

shipment,

due

act

God,

and

cosmetic

damage;

Signal

reception

problems

and

failures

due

line

power

surge;

User

Removal

Memory

Devices/Video

Pick-up

Tubes/CCD

Image

Sensors

are

covered

for

days

from

the

date

purchase;

Accessories;

Batteries

(except

that

Rechargeable

Batteries

are

covered

for

days

from

the

date

purchase);

Products

used

for

commercial

purposes,

including,

but

not

limited

rental.

Loss

data

resultant

from

malfunction

hard

drive

other

data

storage

device;

There

are

express

warranties

except

listed

above.

THE

DURATION

ANY

IMPLIED

WARRANTIES,

CLUDING

THE

IMPLIED

WARRANTY

MERCHANTABILITY,

LIMITED

THE

DURATION

THE

EXPRESS

WARRANTY

HEREIN

JVC

SHALL

NOT

LIABLE

FOR

ANY

LOSS

USE

THE

PRODUCT,

INCONVENIENCE,

ANY

OTHER

DAMAGES

WHETHER

DIRECT,

INCIDENTAL

CONSEQUENTIAL

(INCLUDING,

WITHOUT

LIMITATION,

DAMAGE

TAPES

RECORDS

DISCS)

RESULTING

FROM

THE

USE

THIS

PRODUCT

ARISING

OUT

ANY

BREACH

THIS

WARRANTY.

ALL

EXPRESS

AND

IMPLIED

WARRANTIES,

INCLUDING

THE

WARRANTIES

MERCHANTABILITY

AND

FITNESS

FOR

PARTICULAR

PURPOSE,

ARE

LIMITED

THE

WARRANTY

PERIOD

SET

FORTH

ABOVE.

Some

states

not

allow

the

exclusion

incidental

consequential

damages

limitations

how

long

implied

warranty

lasts,

these

limitations

exclusions

may

not

apply

you.

This

warranty

gives

you

specific

legal

rights

and

you

may

also

have

other

rights

which

vary

from

state

state.

JVCKENWOOD

USA

Corporation

Box

22745,

2201

East

Dominguez

Street,

Long

Beach

CA90801-5745

http

://ww

w.us.jvckenwood

.com

REFURBISHED

PRODUCTS

CARRY

SEPARATE

WARRANTY,

THIS

WARRANTY

DOES

NOT

APPLY.

FOR

DETAIL

REFURBISHED

PRODUCT

WARRANTY,

PLEASE

REFER

THE

REFURBISHED

PRODUCT

WARRANTY

INFORMATION

PACKAGED

WITH

EACH

REFURBISHED

PRODUCT.

For

customer

use:

Enter

below

the

Model

No.

and

Serial

which

located

either

the

rear,

bottom

side

the

cabinet.

Retain

this

information

for

future

reference

Model

No.:

Serial

Pur

ase

date:

Name

dealer:

CANADA

JVCKENWOOD

CANADA

INC

Jvc

WARRANTY

Warranty

applies

only

PRODUCT

distributed

Canada

JVCKENWOOD

CANADA

INC.

JVCKENWOOD

CANADA

NC.

(hereafter

called

"JVC")

gives

the

owing

express

warranty

for

each

new

JVC

product

distribu

ted

Canada

JVC

and

sold

authorized

JVC

ealer.

JVC

warrants

that

this

JVC

product

free,

under

normal

use

and

maintenance,

from

any

defects

materia

l and

workmanship

subject

the

following

and

conditions:

Obtain

Warranty

Service:

Standards:

(a)

JVC

product

requiring

service

must

presented

together

any

defects

should

found

JVC

product

within

the

with

proof

purchase.

applicable

terms,

necessary

repairs

shall

made

cost

(b)

The

JVC

product

must

brought

for

service

the

purchaser

for

parts

labour

when

JVC

acknowledges

that

authorized

JVC

Service

Centre.

such

defects

are

due

faulty

material

workmanship.

Limitation:

This

Warranty

shall

not

apply

to:

(a)

Repair

replacement

any

cabinets,

batteries,

plates,

connection

cords,

antennas,

dust

covers,

knobs,

speaker

grills,

speaker

cones,

projection

screens,

projection

screen

savers,

and

all

accessories.

(b)

Any

defects

caused

repairs

required

result

misuse,

abusive

operation,

negligence,

improper

use

and/or

insufficient

care.

(c)

Any

defect

caused

repairs

required

result

not

following

the

instructions

the

operation

manual.

(d)

Any

JVC

product

tampered

with,

adjusted

repaired

any

party

other

than

JVC

authorized

JVC

Service

Centre

personnel.

(e)

Any

JVC

products

which

the

serial

number

has

been

defaced,

modified

removed.

(f)

Maintenance,

cleaning

periodic

check-up

(g)

Conversion

foreign

domestic

voltage

frequency.

(h)

Any

JVC

product

without

the

Canadian

Electrical

Safety

Regulations

ID.

(i)

Any

JVC

products

used

for

commercial

institutional,

rental,

display

purposes.

Parts

......

year

(except

video

head

days)

Labour

...

days

(j)

Any

JVC

product

which

has

been

resold

and

longer

owned

the

original

purchaser.

(k)

Product

purchased

from

·outside

Canada',

"bankruptcy"

'liquidator·.

(I)

Any

defects

caused

fire,

flood,

lightning,

power

surge,

other

events

beyond

the

control

JVC.

(m)

FOR

AUTO

PRODUCTS

Warranty

does

not

cover

elimination

car

static

electrical

interferences,

cleaning

head,

adjustments,

labour

cost

for

the

removal

reinstallation

the

unit

for

repair.

Exc

usion

of A

Express

Warranties:

This

warranty

constitutes

the

entire

express

warranty

given

JVC

for

JVC

products

and

dealer

service

centre

personnel

his,

its

their

agent

employee

is,

are

authorized

extend

enlarge

this

warranty

behalf

JVC.

Disc

aimer

sequential

Damage:

the

extent

the

law

permits

JVC

disclaims

any

responsibility

for

loss

time

use

its

product,

transportation

costs,

any

other

indirect,

incidental

consequential

damage

inconvenience.

WARRANTY

TERM

(VALID

FROM

THE

DATE

PURCHASE)

Product

Parts

Labour

(Years)

Projection

n-Home

Service

Colour

In-Home

(25"

and

above)

1 1

D-ILA

Rear

Projection

In-Home

Service

LCD

In-Home

Service

(25"

and

above)

In-Home

service

provided

where

available.

Where

not

available,

the

purchaser

must

assume

the

responsibility

and

expense

for

the

proper

packing,

shipment

and

all

costs

associated

with

the

delivery

the

equipment

and

from

the

closest

JVC

Authorized

Service

Centre.

Receivers

and

Home

Speakers

purchased

separately.

Front

Projection

and

Car

2 2

Audio

"ARSENAL"

Series

Adapters,

Remote

controls,

Headphones,

Microphones

and

Projector

days

lamps

Wood

Cone

Speakers

5 5

All

her

JVC KS-DR1004D Manuel utilisateur

Marque: JVC

Modèle: KS-DR1004D

Catégorie: Amplificateurs audio de voiture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: JVC KS-DR1004D User manual
español: JVC KS-DR1004D Manual de usuario

JVC KS-DR1004D Manuel utilisateur

JVC KS-DR1004D Manuel utilisateur

dans d''autres langues

Autres documents