Reese 56015-53 Guide d'installation

Marque: Reese

Modèle: 56015-53

Taper: Guide d'installation

Part Number:

56015

Page 1 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

Description QTY

Description

QTY

Driver Side Frame Bracket 1

1/2"-13x1.75”Carriage Bolt GR8 2

Passenger Side Frame Bracket 1

1”x3” Block 2

½-13 U-Bolt GR5 4

1”x2” Block 2

½-13 Nut GR8 10

1/2” Pull Wire 1

½” Conical Washer 10

1.5”x2” Block 2

3.5”x1.5” Block 2

CAUTION: Under no circumstances do we recommend exceeding the towing vehicle

manufacturers recommended vehicle towing capacity, or the lowest rated component of

your system.

READ ALL INSTRUCTIONS BEFORE STARTING THE INSTALLATION OR USE

VEHICLE FORWARD

FIG. 1

WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS MAY CAUSE PROPERTY

LOSS, SERIOUS INJURY, OR DEATH!

10 BOLT INSTALLATION

Equipment Required:

Fastener Kit: 56015F

Wrenches: 3/4"

Drill Bits: 1/8”, 9/16”

Other Tools: Center Punch, Measuring Tape

Torque Wrench, ¾” Crows Foot

Any hardware shown in Figure 1,

but not described in table below

were supplied with 30153 kit.

568

Part Number:

56015

Page 2 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

1. Place the front mounting rail in the bed of the vehicle. Center the rail on the floor of the truck bed and use your tape

measure to locate the proper distance from the rear of the rail to the to the rear edge of the truck box as illustrated on

page 3.

2. Use a center punch to mark the holes in the bed per the illustration. Move the rail out of the way and drill each

position with a 1/8” drill bit. Note: When drilling holes through the bed be sure what is below the truck bed in

those locations.

3. With holes drilled, Raise the rear of the vehicle and remove both rear tires.

4. Temporarily position the frame brackets on the sides of the frame, Aligning the center hole in the bracket with the

existing slot in the truck frame, and check that the 1/8” drilled holes align with the slots in the frame brackets.

NOTE: To install the brackets they need to be tilted in at a 45°to clear the leading edge of the bed hem seem, then

laid flat against the frame rail. Remove the frame brackets from the vehicle after verifying fitment.

5. If all holes align properly enlarge the 1/8” drilled holes to 9/16”. Paint all bare metal. If hole do not align, restart the

installation at step 1 by adjusting 1/8” holes on truck bed. When holes align be sure to remove brackets before

enlarging to 9/16”.

6. Fasten the frame brackets to the frame using the supplied U-bolts (Item3) and conical washer (Item5) with nut (Item

4) be sure to place the correct ¼”x 3.5’x1.5” block (Item 7) behind the bracket as a spacer with the U-Bolt passing

through the bottom hole as shown in figure 1. Tighten snug to keep the bracket from moving.

7. Place the unassembled 5th wheel support arches/slider/goose into the already installed mounting rail. Position the

rearward mounting rail with the support arches/slider/goose by inserting the tabs into the mounting rail and pushing

the mounting rail tight towards the other mounting rail. Ensure that the mounting rail is centered on the bed of the

vehicle. This will position the rail in the correct location and ensure that the 5th wheel will have a snug fit to the

truck. Note: If more than one hitch product will be used with the mounting rails both types should be used at the

same time to align the mounting rails. This will ensure that one product does not compromise the fit of the other.

8. Repeat steps 2-6 for rear rail.

9. To install the center bolt use the supplied pull wire NOTICE! THE SUPPLIED PULL WIRE WILL NEED TO

BE USED ON BOTH SIDES! Thread the pull wire onto the supplied carriage bolt (Item 8) followed by the 1”x3”

block (Item 9). Pull both components through the center slot on the frame. While doing this be sure to include the

1.5”x2” block between the frame and the frame bracket. Place the conical washer (Item 5) on the bolt and secure

with nut (Item 4).

➢Do not install mounting rails over plastic bed liners. Plastic bed liners must be cut out of the way to

provide metal to metal contact. Mounting rails may be installed on spray in liners.

➢Use only bolts, nuts, and washers supplied to install this kit. All bolts and nuts are Grade 8 unless

otherwise specified.

➢These instructions are guidelines only, actual installation is the responsibility of the installer and the

owner. Always measure truck and trailer before installing hitch to be sure that there is clearance at

the cab and at the bumper to allow for turns.

➢Do not install this product on or attempt to tow with a truck with a 5-1/2’ bed unless a sidewinder

pinbox coupler has been installed on the trailer.

Part Number:

56015

Page 3 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

10. Reposition the mounting rails over the holes in the bed and fasten the mounting rail to the frame brackets using the

hardware supplied with the rail kit. Use the U-shaped blocks between the frame bracket or mounting rails and the

truck bed to ensure metal to metal contact. Install center bolt using the supplied 1”x2” block (Item 10) on the bottom

side of the bed floor and hand tighten.

11. Starting with the hardware that fastens the mounting brackets to the bed rails and torque all the nuts. Torque the 1/2”

GR8 bolts to 110ft-lbs (149N*M), and the 1/2” U-bolts to 75 ft-lbs (101N*M).

12. Re-install both rear wheels.

24-13/16”

46-3/4”

Back Edge of Truck Bed

Bolt Locations

Typical of Both Sides

[5.5’/6.5’ TRUCK BED]

VEHICLE FORWARD

℄AXLE

℄HITCH

¾”

Part Number:

56015

Page 4 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

VEHICLE FORWARD

NOTE: U-Bolt needs to be routed between the frame and

harness as shown above.

NOTE: Fastener to be fished

through frame rail as shown.

Part Number:

56015

Page 5 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

VEHICLE FORWARD

NOTE: U-Bolt needs to be routed between the frame and

harness as shown above. The Harness clip may have to be

temporarily removed from the frame to install U-Bolt and

Bracket.

NOTE: Fastener to be fished

through frame rail as shown.

Part Number:

56015

Page 6 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

NOTE: Be sure to tighten U-Bolts evenly! Deflection in the

bracket below the vehicle frame (shown above) is expected

and is acceptable.

Part Number:

56015

Page 7 of 7

Installation Instructions

REESE®CUSTOM QUICK INSTALL MOUNTING KIT

FOR 30153 REESE®RAILS ONLY

GMC/Chevy 1500 Pickup *See website applicable years & models

LIMITED LIFETIME WARRANTY

Horizon Global Corporation. (“We” or “Us”) warrants to the original consumer purchaser only (“You”) that the product

will be free from material defects in both material and workmanship, ordinary wear and tear expected; provided that

installation and use of the product is in accordance with product instructions. There are no other warranties, express

or implied, including the warranty of merchantability or fitness for a particular purpose. This warranty is not

transferable.

This warranty does not cover: (a) normal wear and tear; (b) damage through abuse, neglect, misuse, or as a result of

any accident or in any other manner; (c) damage from misapplication, overloading, or improper installation; (d)

improper maintenance and repair; and (e) product alteration in any manner by anyone other than Us, with the sole

exception of alterations made pursuant to product instructions and in a workmanlike manner.

To make a Warranty claim, contact Us, at our principal address of 47912 Halyard Dr. Suite 100, Plymouth, MI 48170,

1-800-632-3290, identify the product by model number, and follow the claim instructions that will be provided. Any

returned product that is replaced by Us becomes our property. You will be responsible for return shipping costs.

Please retain your purchase receipt to verify date of purchase and that You are the original consumer purchaser. The

product and the purchase receipt must be provided to Us in order to process Your Warranty claim.

Product replacement is Your sole remedy under this Warranty. We shall not be liable for service or labor charges

incurred in removing or replacing a product or any incidental or consequential damages of any kind.

You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the

product instructions is at Your own risk.

This Warranty gives you specific legal rights, and You may also have other rights which vary from state to state. This

Warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to conflicts of law. The

state courts located in Oakland County, Michigan shall have exclusive jurisdiction for any disputes relating to this

warranty.

Horizon Global

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

For the most up to date product

instructions, installation and use

information please scan the QR

code or call

1-800-632-3290

Printed in XXX

REESE RAIL MOUNTING KIT #30153

PREMIUM-OUTBOARD MOUNTING SYSTEM

SAE J2638 RATED

INSTRUCTIONS

For Installation Assistance or Technical Help, Call 1-888-521-0510

BASERAILS QTY.

1.REESE BASERAIL (2)

2. ½” X 2” GR. 8 CARRIAGE BOLT (10)

3. TRUCK BED SPACER (10)

4. 1/2” CONICAL TOOTHED WASHER (10)

5. 1/2” NUT (10)

Fig. 1

SHEET 1 0F 2

REESE PREMIUM FEATURES

•Kit must be mounted with REESE Series Custom mounting kits (part #

56000 series only) which are mounted outboard, allowing for fast easy

installations

•Meets latest North American testing standards, SAE J2638

•Grade 8 hardware, meets all North American requirements for

commercial & recreational towing

Printed in XXX

The following information is an overview of the installation of a fifth wheel above bed mounting kit, and meant as

supplemental information only. For detailed instructions refer to the instructions given with the corresponding REESE

Series Custom mounting kits (part # 56000 series only). Check parts supplied in kit against parts list (Fig 1) to become

familiar with parts in this kit.

For Installers

For corresponding Custom Quick Install Mounting Kit part number as well as latest revision of installation instructions

please refer to (www.REESEPROD.COM).

1. Do not install mounting rails over plastic bed liners. Plastic bed liners must be cut out of the way. Base rails may be

installed on spray in liner. Note: Consult installer for recommended curing time.

2. Use only CEQUENT PERFORMANCE PRODUCTS, INC. supplied bolts, nuts, and washers to install this kit. All

bolts are Grade 8 hardware.

3. See that owner receives and fills out warranty information page.

Owner Responsibilities

•Refer to rail label and rail markings for correct weight capacity

•Check mounting system bolt tightness once per year

•Save warranty sheet and receipt for any future support

LIMITED LIFETIME WARRANTY

Part No:_______________________________ Date of Original Purchase:____________

Original Owner:_________________________ Original Installer:____________________

1. Limited Lifetime Warranty (“Warranty”). Cequent Performance Products, Inc. ("We" or “Us”) warrants to the original

consumer purchaser only ("You") that the product will be free from material defects in both material and

workmanship, ordinary wear and tear excepted; provided that installation and use of the product is in accordance with

product instructions. There are no other warranties, express or implied, including the warranty of merchantability or

fitness for a particular purpose. This warranty is not transferable.

2. Limitations on the Warranty. This Warranty does not cover: (a) normal wear and tear; (b) damage through abuse,

neglect, misuse, or as a result of any accident or in any other manner; (c) damage from misapplication, overloading,

or improper installation; (d) improper maintenance and repair; and (e) product alteration in any manner by anyone

other than Us, with the sole exception of alterations made pursuant to product instructions and in a workmanlike

manner.

3. Obligations of Purchaser. To make a Warranty claim, contact Us, at our principal address of 47912 Halyard Dr.

Suite 100, Plymouth, MI 48170, 1-888-521-0510, identify the product by model number, and follow the claim

instructions that will be provided. Any returned product that is replaced by Us becomes our property. You will be

responsible for return shipping costs. Please retain your purchase receipt to verify date of purchase and that You are

the original consumer purchaser. The product and the purchase receipt must be provided to Us in order to process

Your Warranty claim.

4. Remedy Limits. Product replacement is Your sole remedy under this Warranty. We shall not be liable for service or

labor charges incurred in removing or replacing a product or any incidental or consequential damages of any kind.

5. Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the

specified use(s) stated in the product instructions is at Your own risk.

6. Governing Law. This Warranty gives You specific legal rights, and You also may have other rights which vary from

state to state. This Warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to

conflicts of law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction for any

disputes relating to this Warranty. Cequent Performance Products, Inc.

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

SHEET 2 0F 2

Printed in XXX

KIT DE MONTAJE DE LARGUEROS REESE # 30153

SISTEMA PREMIUM DE MONTAJE EXTERNO-

SAE J2638 CALIFICADO

INSTRUCCIONES

Para asistencia con la instalación o ayuda técnica, llame al 1-888-521-0510

LARGUEROS BASE CANT.

1.LARGUERO BASE REESE (2)

2. PERNO DE CARRUAJE , ½ "X 2" GR. 8 (10)

3. ESPACIADOR PARA LA BASE DEL VEHÍCULO (10)

4. ARANDELA CÓNICA DENTADA , 1/2” (10)

5. TUERCA, 1/2” (10)

Fig. 1

Hoja 1 de 2

CARACTERÍSTICAS DE REESE PREMIUM

•El Kit debe ser instalado con los kits de montaje a la medida de la serie

REESE (parte # 56000 de la serie únicamente) que se montan desde el

exterior, lo que permite una instalación fácil y rápida

•Cumple con las últimas normas de prueba norteamericanas SAE J2638

•Las piezas Grado 8 cumplen todos los requisitos para América del

Norte para remolque comercial y recreacional

Printed in XXX

La siguiente información es un resumen de la instalación de una quinta rueda por encima del kit de montaje de la base,

cuya finalidad es sólo como información complementaria. Para obtener instrucciones detalladas, consulte las

instrucciones entregadas con los kits para montaje a la medida de la serie Reese correspondientes (parte # 56000 de

la serie únicamente). Revise las partes suministradas contra la lista de partes (Fig. 1) para familiarizarse con las

partes de este kit.

Para los instaladores

Para el número de parte del kit correspondiente de montaje de instalación rápida a la medida así como para la última

revisión de las instrucciones de instalación, consulte (www.REESEPROD.COM).

1. No instale largueros de montaje sobre los forros plásticos de la base. Los forros plásticos de la base se deben

recortar para despejar el camino. Los largueros base se pueden instalar sobre el forro aplicado con rociador.

Nota: Consulte con el instalador para las recomendaciones de tiempo de curado.

2. Use únicamente los pernos, tuercas y arandelas suministrados por CEQUENT PERFORMANCE PRODUCTS, Inc.

para instalar este kit. Todos los tornillos son grado 8.

3. Verifique que el propietario reciba y llene la página de información de la garantía.

Responsabilidades del propietario

•Consulte la etiqueta de los largueros y las marcas en los largueros para la capacidad de peso correcto

•Revise la firmeza de los pernos del sistema de montaje una vez al año

•Guarde la garantía y el recibo para cualquier referencia futura

GARANTÍA LIMITADA DE POR VIDA

Número de parte:_______________________________ Fecha de compra original :____________

Propietario original :_________________________ Instalador original: ____________________

1. GARANTÍA DE POR VIDA LIMITADA (Garantía) Cequent Performance Products, Inc. ("Nosotros” o “Nuestro”) garantiza al

comprador minorista original únicamente ("usted") que el producto estará libre de defectos materiales y de mano de obra, con la

excepción del uso y desgaste habitual, siempre y cuando la instalación y el uso del producto esté de acuerdo con las instrucciones

del producto. No existen otras garantías, expresas o implícitas, incluida la garantía de comerciabilidad o idoneidad para un

propósito en particular. Esta garantía no es transferible.

2. Limitaciones de la garantía. Esta garantía limitada no cubre lo siguiente: (a) desgaste normal y habitual; (b) daño por abuso,

negligencia, mal uso, o como resultado de cualquier accidente o de cualquier otra manera; (c) daño por aplicación o instalación

incorrectas o sobrecarga; (d) mantenimiento y reparación incorrectos; y (e) alteración del producto de cualquier manera por alguien

que no seamos nosotros, con la única excepción de alteraciones realizadas de acuerdo con las instrucciones del producto y de una

manera profesional.

3. Obligaciones del comprador. Para hacer una reclamación de garantía, contáctenos en nuestra dirección principal en 47912

Halyard Dr. Suite 100, Plymouth, MI 48170, 1-888-521-0510, identifique el producto por número de modelo y siga las instrucciones

que se le darán para la reclamación. Cualquier producto devuelto que se reemplace o se reembolse se convierte en propiedad

nuestra. Usted será responsable por los costos de envío del producto. Conserve el recibo de compra para verificar la fecha de

compra y que usted es el comprador original. Nos debe entregar el producto y el recibo de compra para procesar su reclamo de

garantía.

4. Límites de compensación. La sustitución del producto es su único recurso bajo esta garantía. No seremos responsables por el

servicio o cargos de mano de obra en los que se incurra al quitar o reemplazar un producto o cualquier daño de cualquier tipo.

5. Riesgo asumido Usted reconoce y acepta que cualquier uso del producto para cualquier propósito diferente al uso(s)

especificado(s) en las instrucciones del producto es a su propio riesgo.

6. Ley gobernante. Esta garantía le otorga derechos legales. Usted también podría tener otros derechos que varían de estado a

estado. Esta garantía está regida por las leyes del estado de Michigan, sin importar las normas relativas a conflictos de Las cortes

estatales ubicadas en el condado de Oakland, Michigan tendrán la jurisdicción exclusiva para cualquier disputa que surja con

respecto a esta garantía. Cequent Performance Products, Inc.

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

Hoja 2 de 2

Printed in XXX

ENSEMBLE DE TRAVERSES DE MONTAGE REESE No 30153

SYSTÈME DE MONTAGE EXTERNE HAUT DE GAMME HOMOLOGUÉ SAE J2638

INSTRUCTIONS

Pour obtenir de l'assistance pour l'installation ou un autre aspect technique, composer le 1-888-521-0510

TRAVERSES QTÉ

1.TRAVERSE REESE (2)

2. BOULON DE CARROSSERIE ½” x 2” GR. 8 (10)

3. ESPACEUR (PLATEFORME CAMIONNETTE) (10)

4. RONDELLE CONIQUE DENTÉE 1/2” (10)

5. ÉCROU 1/2” (10)

Fig. 1

Feuille 1 de 2

CARACTÉRISTIQUES DE QUALITÉ SUPÉRIEURE REESE

•L'ensemble de traverses doit être assemblé à l'aide des nécessaires de

montage Series Custom REESE (série no 56000 seulement) montés à

l'extérieur, conçus pour faciliter et accélérer les installations.

•Notre système est conforme à la norme d'essai nord-américaine la plus

récente (SAE J2638).

•Boulonnerie de classe 8 qui répond aux normes nord-américaines en ce

qui a trait au remorquage commercial et récréatif.

Printed in XXX

Les renseignements suivants consistent en une vue d'ensemble de l'installation d'un attelage à sellette au-dessus du

système de montage sur plateforme et ne sont fournis qu'à titre d'information complémentaire seulement. Pour des

directives détaillées, se reporter aux instructions fournies avec les nécessaires de montage correspondants de marque

REESE Series Custom (série no 56000 seulement). Comparer les pièces incluses dans le nécessaire à la liste des

pièces (Fig. 1) afin de se familiariser avec les composants du système.

Installateurs

Pour obtenir le numéro de pièce du nécessaire de montage rapide et la dernière version des instructions d'installation,

veuillez vous reporter à (www.REESEPROD.COM).

1. Ne pas installer les traverses sur la doublure de caisse en plastique. La doublure de caisse en plastique doit être

découpée pour libérer l'accès. Les traverses peuvent être installées sur une doublure pulvérisée en place.

Nota : Consulter l'installateur pour connaître le temps de durcissement recommandé.

2. Utiliser seulement les boulons, écrous et rondelles fournis par CEQUENT PERFORMANCE PRODUCTS, Inc. pour

installer ce produit. Tous les boulons et les écrous sont de classe 8 (Grade).

3. S'assurer que le propriétaire a bien reçu et rempli la page de renseignements sur la garantie.

Responsabilités du propriétaire

•Se reporter à l'étiquette et aux inscriptions sur les traverses pour connaître la capacité de charge exacte.

•Vérifier le serrage des boulons du système de montage une fois par année

•Conserver la fiche de la garantie et la preuve d'achat en cas de besoin d'assistance.

GARANTIE À VIE LIMITÉE

No pièce :____________________ Date de l'achat initial :_____ _______

Propriétaire initial :_ Installateur initial :____________ ________

1. Garantie à vie limitée (« Garantie »). Cequent Performance Products, Inc. (« Nous ») garantit à l’acheteur initial seulement

(« Vous ») que le produit sera exempt de vices de matières et de fabrication, exception faite de l’usure normale, dans la mesure

où l’installation et l’utilisation du produit sont conformes aux instructions accompagnant celui-ci. Aucune autre garantie, expresse

ou implicite, ne s’applique, y compris les garanties relatives à la qualité marchande ou à l'adéquation à un usage particulier. Cette

garantie n’est pas transférable.

2. Limites de la garantie. Cette garantie ne couvre pas : (a) l’usure normale; (b) les dommages causés par l’abus, la négligence,

une mauvaise utilisation, ou résultant de tout accident survenu de quelque manière que ce soit; (c) les dommages causés par

une application inappropriée, une charge excessive ou une installation inadéquate; (d) un entretien ou une réparation inadéquate;

(e) un produit modifié de quelque manière que ce soit par quiconque d’autre que Nous, à l’exception des modifications stipulées

dans les instructions accompagnant le produit et réalisées selon les règles de l’art.

3. Obligations de l’acheteur. Pour effectuer une réclamation, communiquez avec nous à notre adresse principale, 47912 Halyard

Dr. Suite 100, Plymouth, MI 48170, 1-888-521-0510, et veuillez identifier le produit d'après le numéro de modèle et suivre les

directives qui vous seront fournies. Tout produit retourné qui est remplacé par Nous devient notre propriété. Vous serez tenu

d’assumer les frais d’expédition de retour. Veuillez conserver votre reçu d’achat afin que nous puissions en vérifier la date et

confirmer que Vous êtes l'acheteur initial. Le produit et le reçu d’achat doivent Nous être fournis afin que nous puissions traiter

Votre réclamation.

4. Limites des recours. Le remplacement du produit est Votre seul recours en vertu de cette Garantie. Nous ne sommes pas

responsables des frais de service ou de main-d’oeuvre encourus pour l’enlèvement ou la réinstallation d’un produit, ni des

dommages accessoires ou indirects, quels qu’ils soient.

5. Acceptation des risques. Vous reconnaissez et acceptez que toute utilisation du produit à des fins autres que celle(s)

stipulée(s) dans les instructions relatives au produit est faite à vos propres risques.

6. Loi applicable. Cette Garantie Vous confère des droits légaux spécifiques, et il se peut que Vous possédiez d’autres droits qui

peuvent varier d’une province à l’autre. Cette Garantie est régie par les lois de l’État du Michigan, abstraction faite des règles

relatives aux conflits de lois. Les cours de l’État situées dans le comté d’Oakland, Michigan, constituent les autorités judiciaires

exclusives relativement à tout litige relevant de cette Garantie. Cequent Performance Products, Inc.

47912 Halyard Dr. Suite 100

Plymouth, MI 48170

Feuille 2 de 2

Reese 56015-53 Guide d'installation

Marque: Reese

Modèle: 56015-53

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Reese 56015-53 Installation guide
español: Reese 56015-53 Guía de instalación

Documents connexes

Autres documents

Draw-Tite 45511 Guide d'installation