EGO CS1800-FC 18 Inch Brushless Cordless Chainsaw Manuel utilisateur

OPERATOR'S MANUAL

56V LITHIUM-ION

CORDLESS 18" CHAIN SAW

MODEL NUMBER CS1800/CS1800-FC

BRUSHLESS

WARNING: To reduce the risk of injury, the user must read and understand the

Operator’s Manual before using this product. Save these instructions for future reference.

272652

Español p. 101

Français p. 49

FILL OIL TANK WITH BAR AND

CHAIN OIL BEFORE FIRST USE

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC2

TABLE OF CONTENTS

Safety Symbols ..........................................4

Safety Instructions .....................................5-16

Glossary of terms ....................................16-17

Introduction ............................................17

Specications ..........................................18

Packing List ............................................18

Description .........................................19-21

Assembly ..............................................22

Operation ...........................................23-35

Maintenance ........................................36-44

Troubleshooting ......................................45-46

Warranty ...........................................47-48

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 3

READ ALL INSTRUCTIONS!

WARNING: Some dust created by power sanding, sawing, grinding, drilling

and other construction activities contains chemicals known to the state of California

to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

◾Lead from lead - based paints

◾Crystalline silica from bricks and cement and other masonry products, and

◾Arsenic and chromium from chemically - treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemical: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to lter out microscopic particles.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC4

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The

safety symbols and the explanations with them deserve your careful attention and

understanding. The symbol warnings do not, by themselves, eliminate any danger. The

instructions and warnings they give are no substitutes for proper accident prevention

measures.

WARNING: Be sure to read and understand all safety instructions in this

Operator’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,”

and “CAUTION” before using this tool. Failure to follow all instructions listed below may

result in electric shock, re, and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION. May

be used in conjunction with other symbols or pictographs.

WARNING! The operation of any power tools can result in

foreign objects being thrown into your eyes, which can result in severe

eye damage. Before beginning power tool operation, always wear

safety goggles or safety glasses with side shields and a full face shield

when needed. We recommend a Wide Vision Safety Mask for use over

eyeglasses or standard safety glasses with side shields. Always use eye

protection which is marked to comply with ANSI Z87.1.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 5

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may appear on this product. Read,

understand, and follow all instructions on the machine before attempting to assemble

and operate it.

Safety Alert Indicates a potential personal injury hazard.

Read &

Understand

Operator's

Manual

To reduce the risk of injury, user must read

and understand the operator’s manual before

using this product.

Wear Eye

Protection

Always wear safety goggles or safety glasses

with side shields and a full face shield when

operating this product.

Wear Ear

Protection

Chain saw noise may damage your hearing.

Always wear sound barriers (ear plugs or ear

mufers) to protect your hearing.

Wear Head

Protection

Wear an approved safety hard hat to protect

your head.

Wear Protective

Gloves

Protect your hands with gloves when

handling saw and saw chain. Heavy-duty,

nonslip gloves improve your grip and protect

your hands.

Be aware of

kickback

Contact of the guide bar tip with any object

should be avoided.

Guide bar tip

kickback

Tip contact can cause the guide bar to move

suddenly upward and backward, which can

cause serious injury.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC6

Two handed hold Always use two hands when operating the

chain saw.

Recycle Symbols

This product uses lithium-ion (Li-ion)

batteries. Local, state, or federal laws may

prohibit disposal of batteries in ordinary

trash. Consult your local waste authority for

information regarding available recycling and/

or disposal options.

IPX4 Ingress Protection

Degree Protection from splashing water

Direct Current Type or a characteristic of current

V Volt Voltage

mm Millimeter Length or size

in. Inch Length or size

kg Kilogram Weight

lb Pound Weight

ml Milliliter Volume

.oz Fluid Ounce Volume

°C Celsius

Temperature Temperature

°F Fahrenheit

Temperature Temperature

GENERAL BATTERY-OPERATED POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings, instructions, illustrations and

specications provided with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 7

WORK AREA SAFETY

◾Keep work area clean and well lit. Cluttered or dark areas invite accidents.

◾Do not operate power tools in explosive atmospheres, such as in the

presence of ammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

◾Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

PERSONAL SAFETY

◾Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the inuence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury.

◾Always use personal protective equipment. Personal protective equipment

such as eye protection, dust mask, non-skid safety shoes, hard hat and/or

hearing protection used for appropriate conditions will reduce personal injuries.

◾Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to the battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energizing power tools that

have the switch on invites accidents.

◾Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a moving part of the power tool may result in

personal injury.

◾Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

◾Dress properly. Do not wear loose clothing or jewelry. Keep your hair and

clothing away from moving parts. Loose clothes, jewelry or long hair can be

caught in moving parts.

◾If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used. Use

of dust collection can reduce dust-related hazards.

◾Do not let familiarity gained from frequent use of tools allow you to

become complacent and ignore tool safety principles. A careless action

can cause severe injury within a fraction of a second.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC8

POWER TOOL USE AND CARE

◾Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the rate for

which it was designed.

◾Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and must be

repaired.

◾Remove the battery pack, if detachable, from the power tool and/or

activate any battery disabling device before clearing jammed material,

making any adjustments, changing accessories, cleaning, or storing

power tools. Such preventive safety measures reduce the risk of starting the

power tool accidentally.

◾Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate

the power tool. Power tools are dangerous in the hands of untrained users.

◾Maintain power tools and accessories. Check for misalignment or

binding of moving parts, breakage of parts and any other condition that

may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power

tools and accessories.

◾Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

◾Use the power tool, accessories, tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to

be performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

◾Keep handles and grasping surfaces dry, clean and free from oil and

grease. Slippery handles and grasping surfaces may lead to unsafe handling

and/or loss of control of the tool.

BATTERY TOOL USE AND CARE

◾Recharge only with the charger specied by the manufacturer. A charger

that is suitable for one type of battery pack may create a risk of re when used

with another battery pack.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 9

◾Use power tools only with specically designated battery packs. Use of

any other battery packs may create a risk of injury and re.

◾When battery pack is not in use, keep it away from other metal objects,

like paper clips, coins, keys, nails, screws or other small metal objects,

that can make a connection from one terminal to another. Shorting the

battery terminals together may cause burns or a re.

◾Under abusive conditions, liquid may be ejected from the battery; avoid

contact. If contact accidentally occurs, ush with water. If liquid contact

eyes, additionally seek medical help. Liquid ejected from the battery may

cause irritation or burns.

◾Do not use a battery pack or tool that is damaged or modied. Damaged

or modied batteries may exhibit unpredictable behavior resulting in re,

explosion or risk of injury.

◾Do not expose a battery pack or tool to re or excessive temperature.

Exposure to re or temperature above 265 °F (130°C) may cause explosion.

◾Follow all charging instructions and do not charge the battery pack or

tool outside the temperature range specied in the instructions. Charging

improperly or at temperatures outside the specied range may damage the

battery and increase the risk of re.

SERVICE

◾Have your power tool serviced by a qualied repair person using only

identical replacement parts. This will ensure that the safety of the power tool

is maintained.

◾Never service damaged battery packs. Service of battery packs should only

be performed by the manufacturer or authorized service providers.

SAFETY INSTRUCTIONS FOR CHAIN SAW

◾Keep all parts of the body away from the saw chain when the chain saw

is operating. Before you start the chain saw, make sure that the saw

chain is not contacting anything. A moment of inattention while operating

chain saws may cause entanglement of your clothing or body with the chain.

◾Always hold the chain saw with your right hand on the rear handle and

your left hand on the front handle. Holding the chain saw with a reversed hand

conguration increases the risk of personal injury and should never be done.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC10

◾Hold the chain saw by insulated gripping surfaces only, because the saw

chain may contact hidden wiring. Saw chains contacting a “live” wire may

make exposed metal parts of the chain saw“live” and could give the operator an

electric shock.

◾Wear eye protection. Further protective equipment for hearing, head,

hands, legs and feet is recommended. Adequate protective equipment will

reduce personal injury from ying debris or accidental contact with the saw

chain.

◾Do not operate a chain saw in a tree, on a ladder, from a rooftop, or

any unstable support. Operation of a chain saw in this manner could result in

serious personal injury.

◾Always keep proper footing and operate the chain saw only when

standing on xed, secure and level surface. Slippery or unstable surfaces

may cause a loss of balance or control of the chain saw.

◾When cutting a limb that is under tension be alert for spring back. When

the tension in the wood bers is released the spring loaded limb may strike the

operator and/or throw the chain saw out of control.

◾Use extreme caution when cutting brush and saplings. The slender

material may catch the saw chain and be whipped toward you or pull you off

balance.

◾Carry the chain saw by the front handle with the chain saw switched off

and away from your body. When transporting or storing the chain saw,

always t the guide bar cover. Proper handling of the chain saw will reduce

the likelihood of accidental contact with the moving saw chain.

◾Follow instructions for lubricating, chain tensioning and changing the

bar and chain. Improperly tensioned or lubricated chain may either break or

increase the chance for kickback.

◾Cut wood only. Do not use chain saw for purposes not intended. For

example: do not use chain saw for cutting metal, plastic, masonry or

non-wood building materials. Use of the chain saw for operations different

than intended could result in a hazardous situation.

◾Do not attempt to fell a tree until you have an understanding of the

risks and how to avoid them. Serious injury could occur to the operator or

bystanders while felling a tree.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 11

CAUSES AND OPERATOR PREVENTION OF KICKBACK

Kickback may occur when the nose or tip of the guide bar touches an object,

or when the wood closes in and pinches the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse reaction, kicking the

guide bar up and back towards the operator.

Pinching the saw chain along the top of the guide bar may push the guide bar

rapidly back towards the operator.

Either of these reactions may cause you to lose control of the saw, which

could result in serious personal injury. Do not rely exclusively upon the safety

devices built into your saw. As a chain saw user, you should take several

steps to keep your cutting jobs free from accident or injury.

Kickback is the result of chain saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper precautions as

given below:

◾Maintain a rm grip, with thumbs and ngers encircling the chain saw

handles, with both hands on the saw and position your body and arm to

allow you to resist kickback forces. Kickback forces can be controlled by the

operator, if proper precautions are taken. Do not let go of the chain saw.

◾Do not overreach and do not cut above shoulder height. This helps prevent

unintended tip contact and enables better control of the chain saw in unexpected

situations.

◾Only use replacement guide bars and saw chains specied by the

manufacturer. Incorrect replacement guide bars and saw chains may cause

chain breakage and/or kickback.

◾Follow the manufacturer’s sharpening and maintenance instructions

for the saw chain. Decreasing the depth gauge height can lead to increased

kickback.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC12

KICKBACK SAFETY DEVICES ON THIS CHAIN SAW

Chain Brake

The chain saw comes equipped with a chain brake, which stops both the motor and

the motion of the chain when kickback occurs. The chain brake can be activated by

the forward motion of the chain-kickback brake handle as the saw rotates backward

during kickback; it can also be activated by the inertial forces generated during rapid

pushback.

WARNING: Never modify or attempt to disable the chain brake.

Make sure that the chain brake is working properly before using the chain saw. The

chain-kickback brake handle should move back and forth easily.

To test the operation of the chain brake,

perform the following steps (Fig. 1):

◾Place the chain saw on a at bare

surface and make sure no objects

or obstructions that could come in

contact with the bar and chain are in

the immediate vicinity.

◾Disengage the chain brake by

pulling the chain-kickback brake

handle towards the front handle.

◾Start the chain saw.

◾Push the chain-kickback brake handle towards the front of the saw. A properly

functioning hand brake will stop the movement of the chain immediately. If the

chain brake is not working properly, do not use the chain saw until it has been

repaired by a qualied service technician.

WARNING: Conrm that the chain brake works properly before each use.

WARNING: If the chain brake is clogged with wood chips, the function of the

chain brake may deteriorate. Always keep the device clean.

1Chain kickback brake

handle in operationg position

Chain kickback brake

handle in brake position

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 13

Low Kickback Saw Chain

The ramp-shaped depth gauges ahead of each cutter can minimize the force of a

kickback reaction by preventing the cutters from digging in too deeply at the kickback

zone. Only use a replacement chain that is equivalent to the original chain or has been

certied as a low kickback chain per ANSI B175.1. A low kickback tooth saw chain is a

chain that has met the kickback performance requirements of ANSI B175.1 (American

National Standard for Power Tools-Gasoline-Powered Chain Saws-Safety Requirements)

when tested on the representative sample of chain saws below 3.8 c.i.d. specied in

ANSI B175.1.

The bumper drive link (Fig. 2) also helps

deliver low-kickback performance.

CAUTION: As saw chains are

sharpened during their useful life, they

lose some of the low kickback qualities

and extra caution should be used.

GUIDE BAR

This saw comes equipped with a guide

bar that has a small radius nose. Small radius noses generally have less potential for

kickback. When replacing the guide bar, be sure to order the bar listed in this manual.

2

Bumper drive link Cutter type

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC14

ADDITIONAL WARNINGS

◾With a basic understanding of

kickback (Fig. 3-5), you can

reduce or eliminate the element

of surprise. Sudden surprise

contributes to accidents.

◾Make sure that the area in

which you are cutting is free

from obstructions. Do not let

the nose of the guide bar contact

a log, branch, fence, or any other

obstruction that could be hit while

you are operating the saw.

◾Inspect the work piece for nails,

wire, or other foreign objects

prior to cutting.

◾Plan the work, ensuring an

obstacle-free work area and, in

the case of felling, at least one

escape path from the falling

tree.

◾When felling, keep bystanders

at least two tree lengths away.

◾Keep proper footing and balance

at all times.

BRUSHLESS

3Rotational

kickback

4Kickback

danger zone

5Linear kickback

Kickback

Pinch

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 15

◾A chain saw is intended for two

handed use. Serious injury to the

operator, helpers, and/or bystanders

can result from one-handed

operation (Fig. 6).

◾Always cut with the unit running

at full speed. Fully squeeze the

switch trigger and maintain cutting

speed.

◾Push and Pull – The reaction force

is always opposite to the direction

the chain is moving where wood

contact is made. Thus, the operator

must be ready to control the PULL

when cutting on the bottom edge of

the bar, and the PUSH when cutting

along the top edge (Fig. 7).

◾Avoid unintentional contact

with the stationary saw chain or

guide bar rails. These can be very

sharp. Always wear gloves and long

pants or chaps when handling the

chain saw, saw chain, or guide bar.

◾Never operate a chain saw

that is damaged or improperly

adjusted or that is not

completely and securely

assembled. Be sure that the saw

chain stops moving when the trigger

switch is released.

◾When bucking, secure the work piece prior to cutting. When felling or

pruning, identify and secure hazardous branches.

◾Aggressive or abusive cutting or misuse of the chain saw can cause

premature bar, chain, and/or sprocket wear, as well as a broken chain or

bar, leading to kickback, chain throw or the ejection of material.

BRUSHLESS

6

7

Pull

Push

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC16

◾Never use the guide bar as a lever. A bent guide bar can cause premature bar,

chain, and/or sprocket wear, as well as a broken chain or bar, leading to kickback,

chain throw or the ejection of material.

◾Cut only one work piece at a time.

◾Use only with the battery packs and chargers listed below:

BATTERY PACK CHARGER

BA1400, BA1400-FC, BA2800, BA2800-FC,

BA4200, BA4200-FC, BA1400T, BA1400T-FC,

BA2240T, BA2240T-FC, BA2242T, BA2242T-FC,

BA2800T, BA2800T-FC, BA4200T, BA4200T-FC,

BA5600T, BA5600T-FC, BA6720T, BA6720T-FC

CH2100, CH2100-FC,

CH3200, CH3200-FC,

CH5500, CH5500-FC,

CH2800D, CH2800D-FC,

CH7000,CH7000-FC

◾Do not charge the battery pack in rain or in wet locations.

◾If situations occur which are not covered in this manual, use care and

good judgment. Contact EGO Customer Service for assistance.

SAVE THESE INSTRUCTIONS!

GLOSSARY OF TERMS

Automatic Oiler: A system that automatically lubricates the guide bar and saw chain.

Bucking: The process of cross-cutting a felled tree or log into lengths.

Bucking Spikes: The pointed tooth or teeth for use when felling or bucking to pivot

the saw and maintain position while sawing.

Chain Brake: A device used to stop the saw chain immediately.

Chain Saw Power Head: A chain saw without the saw chain or guide bar.

Drive Sprocket: The toothed part that drives the saw chain.

Felling: The process of cutting down a tree.

Felling Back Cut: The nal cut in a tree felling operation made on the opposite side of

the tree from the notching undercut.

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 17

Kickback: The backward or upward motion, or both, of the guide bar, which occurs

when the saw chain near the nose of the top area of the guide bar contacts any object,

such as a log or branch, or when the wood closes in and pinches the saw chain in the

cut.

Low-Kickback Chain: A chain that complies with the kickback performance

requirements of ANSIB175.1 when tested on a representative sample of chain saws.

Normal Cutting Position: Those positions assumed in performing bucking and felling

cuts.

Notching Undercut: A notch cut in a tree that directs the tree’s fall.

Reduced Kickback Guide Bar: A guide bar that has been demonstrated to reduce

kickback signicantly.

INTRODUCTION

Congratulations on your selection of the new generation of 56V Lithium-ion powered

chain saw. It has been designed, engineered and manufactured to give you the best

possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact EGO

customer service center 1-855-EGO-5656.

This manual contains important information on to the safe assembly, operation, and

maintenance of your product. Read it carefully before using the product. Keep this

manual handy so you can refer to it at any time.

SERIAL NUMBER _____________________ DATE OF PURCHASE _________________

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE

PLACE FOR FUTURE REFERENCE

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC18

SPECIFICATIONS

Voltage 56V

Guide Bar Length 18" (450mm)

Chain Pitch 3/8" (9.5mm)

Chain Gauge 0.050" (1.3mm)

Number of drive links 62

Chain Type AC1800

Guide Bar Type AG1800

Chain Oil Tank capacity 7 .oz (200ml)

Operating Temperature 5°F-104°F (-15°C-40°C)

Storage Temperature -4°F-158° F (-20°C-70°C)

Net Weight (Without battery pack, chain

sheath) 9.7 lbs. (4.4 kg)

Recommended Bar and Chain for this Chain Saw

PART NAME MODEL NUMBER

Guide Bar

AG1800(Recommend)

AG1600(Compatible)

AG1400(Compatible)

Saw Chain

AC1800(Recommend)

AC1600(Compatible)

AC1400(Compatible)

PACKING LIST

PART NAME QUANTITY

Chain Saw 1

Chain Sheath 1

Operator's Manual 1

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC 19

DESCRIPTION

KNOW YOUR CHAIN SAW (Fig. 8)

The safe use of this product requires an understanding of the information on the tool

and in this operator’s manual, as well as knowledge of the project you are attempting.

Before using this product, familiarize yourself with all operating features and safety

rules.

8

Chain Kickback Brake Handle

Lock-off Button

Variable-Speed

Trigger Switch

Battery-

Release Button

Saw Chain

Oil-Tank Cap

Oil-Inspection Window Electric Contacts

Bucking Spikes

LED Headlights

LED Button

Ejection Mechanism

Rear Handle

Front Handle

Side Cover

Chain Sheath

Quick Chain-tension Adjust Knob

Guide Bar

Lubricating Hole

56V LITHIUM-ION CORDLESS CHAIN SAW — CS1800/CS1800-FC20

Chain-Kickback Brake Handle

Serves as the lever for chain brake activation. It also provides protection against

projecting branches and helps prevent the left hand from touching the saw chain if it

slips off the front handle.

Variable-Speed Trigger Switch

Turns the chain saw On and Off and adjusts the chain speed.

Lock-off Button

Helps to prevent accidental or unauthorized activating of the trigger switch. It must be

depressed before the trigger switch can be activated.

Oil-Tank Cap

Seals the oil tank.

Oil-Inspection Window

Provides a view of the oil level in the oil tank.

Saw Chain

A loop of chain having cutting teeth that cut the wood when it is driven by the chain

saw power head and supported by the guide bar.

Chain Sheath

The chain sheath keeps the operator from coming in contact with the sharp chain

blades when the tool is not in use. It also helps keep the chain blades from being

nicked or damaged when the tool is in transportation and storage.

Guide Bar

Supports and guides the saw chain.

Front Handle

The support handle for the left hand at the front of the chain saw.

La page charge ...

EGO CS1800-FC 18 Inch Brushless Cordless Chainsaw Manuel utilisateur

Ce manuel convient également à

EGO CS1800-FC 18 Inch Brushless Cordless Chainsaw Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents