OttLite NS2009-SHPR Manuel utilisateur
- Catégorie
- Hauts-parleurs portatifs
- Taper
- Manuel utilisateur
Ce manuel convient également à
Dual Shade LED Lamp with Bluetooth® Speaker
NS2009 NS2009-SHPR HSD9036A
CO N GR AT UL ATI O NS !
You’ve purchased the finest in natural lighting technology with your new
OttLite® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it
today by mail, or register online by going to: OttLite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packing placing lamp body base (A) flat on a
steady surface.
2. Connect the AC Adapter input (H) into connector (N) in the rear-top
of the lamp.
3.
Plug the AC adapter (G) into a standard household 120V AC outlet. Note:
Only use with the supplied AC adapter to avoid damage or fire.
4. This lamp offers both LED dimming and color mode function.
5. Turn the lamp ON & OFF by using power “touch” switch (B) located in
the front-upper side of base (A).
6. To power LED lighting, slightly touch switch (B) to achieve the following:
• to turn lamp “ON”; touch the switch “once”
• to turn lamp “OFF”; touch the switch a “second” time.
7. To power LED dimmer setting, slightly touch switch (B) to turn “ON”
lamp and achieve the following:
• to operate dimmer function; continuously “press” switch until light
reaches its lowest setting or “stop” pressing switch when reaching
desired lower light level.
• after reaching desired lower light level, continuously “press” switch
again until reaching original setting.
NOTE: If dimmer function was employed prior to turning “OFF” lamp,
the lamp will return to lamp setting last employed unless disconnected
from adaptor.
8. To adjust lighting color mode: touch “M” key (C) to switch light color
temperature mode; 5000°K, 4000°K, 2700°K. NOTE: 4000°K is the
default color mode.
9. This lamp features a stereo speaker (M) with Bluetooth pairing
and auxiliary device direct plug-in capability to play music directly
through the speaker. Auxiliary input requires a 3.5mm audio cable
(included) to connect your device to the unit.
10. Bluetooth pairing can be turned ON & OFF by using “play/pause”
touch switch (D) located base surface panel. To engage Bluetooth
pairing operation perform the following:
• Press and hold Bluetooth touch switch (D) to engage speaker (M),
Bluetooth indicator light (F) begins to continually “flash” meaning
it is “ready to pair”;
• Engage desired handheld device (such as mobile phone, tablet,
etc.) by searching for device “OttLite” (Lamp with Bluetooth®
Speaker) on handheld device Bluetooth settings, click the device
name to successfully pair and connect the Bluetooth function.
• The blue light will “slowly” flash showing a successful connection
has been made.
11. Perform the following to play music directly to speaker using auxiliary
device plug-in feature:
• Press and hold Bluetooth touch switch (D) to engage speaker (M)
until Bluetooth indicator light (F) begins to
flash. At this time the
speaker is the default to Bluetooth mode.
• Insert 3.5mm audio cable (included) into AUX connection (P) in
the rear-bottom of the lamp.
12. Press and hold touch switches
“+” and “-” (E) for volume adjustment.
Press and hold touch switch “+” to increase volume or press and hold
touch switch “-” to reduce volume.
13. Quickly press touch switches “+” and “-” (E) to make a song track
change. Touch switch “+” to advance to the next song. Touch switch
“-” to go back to the previous song. NOTE: Skip function for track
change is only applicable to Bluetooth mode.
14.
To reposition the light, hold base (A) steady then grasp and adjust either
lamp arm (J) or shade (K) depending on needed position.
15. Refer to Diagrams 1 and 2 for lamp maximum adjustment range.
NOTE: DO NOT FORCE the shade or lamp body rotation outside
allowable adjustment range as excessive adjustment may cause
damage.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (K) AND ADAPTER (G)
ARE COOL before handling.
2. The LED panel (L) might get hot after several hours of continuous use,
DO NOT place your hands directly on LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted
into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the
consumer.
6. INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction
sheet are not meant to cover all possible conditions and situations that
may occur. It must be understood that common sense, caution, and
care must be used with any electrical product.
CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE
IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS
SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
CAN ICES-003 (B)/NMB-003 (B)
CAUTION: Any change or modification to product not expressly
recognized by OttLite Technologies voids OttLite’s responsibility for
proper function of product.
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.7A
Output: 5V DC, 3A with a Male DC Plug
Output power: 2.75W (lamp) + 2.5W (speaker)
Speaker: 1 inch, 4 ohms
Bluetooth V4.2
3.5mm audio cable is required for direct plug-in connection (included)
THIS LAMP CONTAINS a 5V-2.1A USB output port (O) located on
the base of the lamp. USB port can charge such items as tablets,
cellular phones, etc.
ENGLISH Dual Shade LED Lamp with Bluetooth® Speaker
INS180415 REV090919
A
K
J
M
180° 120°
B
CD
E
E
N
O
P
G
H
L
L
* Lamp cannot be used
in this position
F
Diagram 1 Diagram 2
IC WARNING
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation
of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure
and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20 centimeters between
the radiator and your body.
Cet appareil est conforme aux CNR exempts de licence d’Industrie Canada. Le fonctionnement est
soumis aux deux conditions suivantes:
(1) Cet dispositif ne peut causer des interférences; et
(2) Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l’appareil.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 etla
conformité à l’exposition de RSS-102 rf, utilisateurs peut obtenir l’information canadienne surl’exposition
et la conformité de rf.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne
ouémetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20
centimètres entre le radiateur et votre corps.
INS180415 REV090919
-
1
-
2
OttLite NS2009-SHPR Manuel utilisateur
- Catégorie
- Hauts-parleurs portatifs
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: OttLite NS2009-SHPR User manual
Documents connexes
-
OttLite S83WGW Mode d'emploi
-
-
-
-
-
-
-
-
-