dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
WS-77424/WS-77436
774-LED Wall Sconce
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov.2023
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by t he base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Allen Screw
Qty: 12+2 Extra (WS-77424)
20+2 Extra (WS-77436)
Wire Connector
Qty: 4pcs
Mounting Screw
Qty: 1 Extra
A
BD
Allen Wrench
Qty: 1pc
E
C
Assembly screw
Qty: 1pc
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
WS-77424/WS-77436
774-LED Wall Sconce
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov.2023
Fig.4 Switch
Mounting Backplate
Fig.3 WiringFig.1
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1&Fig. 2)
3. Remove the mounting screw (B) from the xture.
4. The lamp can switch between four color temperatures (2700K-3000K-3500K-4000k), which can be adjusted to your preference with the switch in the
canopy (Fig.4).
Note: the switch comes with a detachable cover, Remove the cover prior to adjusting the color temperature, Fasten the cover after adjustment
is made.
5. Loosen the assembly screw(C) and remove the canopy.(Untie the male and female end connector,canopy can be removed completely.)
6. Secure the glasses to the lamp body using Allen screws(E) with Allen wrench(D).
7. Connect the male and female end connector and Secure the canopy using assembly screws(C).
8. Secure the mounting plate to the junction box using the screws provided with the junction box.
Note: (i)Using any other non-original-manufacturer provided junction box screw may result in safety issue.
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
9. Properly secure the safety cord to the bracket on the mounting back plate to temporarily hang the xture in place and aid installation.
10. Connect the input wires to junction box wires as shown (Fig. 3). Make sure that all wire connectors (A) are secure. If your outlet
box has a GND or bare copper ground wire, connect the ground wire to it. Otherwise, connect the xture’s ground wire directly
to the backplate using the GND screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
11. Secure the xture to the mounting back plate using the mounting screw (B).
Black or
Smooth
White or
Ribbed
Bare wire
(Ground)
Black
(Hot)
White
(Neutral)
Green or Bare Copper
(Ground)
Fig.2
Junction
Box
Junction Box
Screw
Wire Connector
A
Ground Wire
Mounting screw
B
Lamp body
Mounting
Backplate Safety
Cord
4CCT Switch
4CCT Switch
Cover
Driver
Male end connector
Female end connector
Glass
(RPL-GLA-77424)
Allen
Wrench
D
Allen
Screw
E
5 3/4"
4 1/8"
1 3/4" 1 3/8"
Canopy
Assembly screw
C
-
1
-
2
WAC Lighting WS-77424 Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
WAC Lighting PD-69432 Mode d'emploi
-
-
-
-
-
-
-
-
-