McQuay A Series Guide d'installation

CEILING CASSETTE

SPLIT TYPE AIR CONDITIONER

(A Series)

INSTALLATION MANUAL

Group: CEILING CASSETTE

Part Number: A08019025503

Date: MAY 2001

IM-CKA-0501-McQuay

OUTLINE AND DIMENSIONS

MODEL A B C D E F G H I J K

20A / 20AR

25A / 25AR

30A / 30AR

820 820 363 335 28 930 930 642 622 555 555

40A / 40AR

(32,2) (32,2) (14,3) (13,2) (1,1) (36,6) (36,6) (25,2) (24,5) (21,9) (21,9)

50A / 50AR

Indoor Unit (CKA Series)

• (With Wireless Remote Control & With Wired Remote Control)

All dimensions are in mm / (in)

i

A

B

C

DE

F

H

M

J

I

G

Outdoor Unit (SL - B Series)

All dimensions are in mm / (in)

Dimension A B C D E F G H J K L M N P Q R

20B / 20BR

840 646 330 297 309 626 41 85 75 177 106 408 378 124 592 78,5

25B / 25BR

(33,1) (25,4) (13,0) (11,7) (12,2) (24,6) (1,6) (3,3) (3,0) (7,0) (4,2) (16,1) (14,9) (4,9) (23,3) (3,1)

30B / 30BR

15 (0,6)

39 (1,5)

840 (33,1)

124 (4,9)

840 (33,1)

297 (11,7)

15 (0,6)

39 (1,5)

5 (0,2)

20 (0,8)

2,5 (0,1)

5 (0,2)

160 (6,3)

141

(5,6)

(2,6)

65

20 (0,8)

78,5 (3,1)

124 (4,9)592 (23,3)

378 (14,9)

408 (16,1)

330 (13,0)

85

(3,3)

41

(1,6)

(3,0)

75

177 (7,0)

106

(4,2)

626 (24,6)

646 (25,4)

309 (12,2)

ii

Dimension A B C D E F G H I J K L M N O

20C/CR 855 628 328 508 181 44 93 149 101 113 603 126 164 17 49

(33,7) (24,7) (12,9) (20,0) (7,1) (1,7) (3,7) (5,9) (4,0) (4,4) (23,7) (5,0) (6,4) (0,7) (1,9)

25C/CR 855 730 328 513 182 44 93 149 101 113 603 126 164 17 47

28C/CR (33,7) (28,7) (12,9) (20,2) (7,2) (1,7) (3,7) (5,9) (4,0) (4,4) (23,7) (5,0) (6,4) (0,7) (1,9)

Dimension P Q R S T

20C/CR 32 3 23 73 75

(1,3) (0,1) (0,9) (2,9) (3,0)

25C/CR 32 3 23 73 75

28C/CR (1,3) (0,1) (0,9) (2,9) (3,0)

All dimensions are in mm / (in)

Outdoor Unit : SL20C / 25C / 28C & CR

iii

Outdoor Unit : SL30C / 40C / 50C & CR

B

A

Q

R

ST

DO

KLL

CN

P

M

N

FE

C

GH

IJ

FOR SL25C/CR

ONLY

141,5

(5,6)

746,5

(29,4)

1030,0 (40,6)

20,0

(0,8)

448,0

(17,6)

850,0 (33,5)

25,0 (1,0)

50,0

(2,0)

85,0

(3,3)

400,0 (15,7)

320,0 (12,6)

40,0

(1,6)

40,0

(1,6)

141,5

(5,6)

20,0

(0,8)

All dimensions are in mm / (in)

iv

! Caution

Sharp edges and coil surfaces are potential locations which may cause

injury hazards. Avoid from being in contact with these places.

! Avertissement

Les bords coupants et les surfaces du refroidisseur tuulaire présentent

un risque de blessure. Mieux vaut éviter le contact avec ces endroits.

! Vorsicht

Scharfe Kanten und Wärmetauscherflächen stellen eine Gefahrenquelle dar.

Jeglicher Kontakt mit diesen Stellen ist zu vermeiden.

! Cautela

Per preservarsi da eventuali ferite, evitare di toccare gli spigoli afilati e la

superficie dei serpentini.

! Cuidado

Los Bordes afilados y la superficie del serpentín pueden producir lesiones.

Evite tocarlos.

! Осторожно

Острые края и поверхности змеевиков являются

потенциальными местами нанесения травм. Остерегайтесь

контакта с этими местами.

This product is subjected to Waste of Electrical and Electronic Equipment Regulations (WEE

E

Regulations). The waste product shall be separately collected by specific collection and treatment centre

.

P

lease refer to local authorithy for these centres. This is only applicable to European Union countries

.

Ce produit est soumis

à

la r

à

é

r

é

chets

d

es

é

lectriques e

t

é

lectroniques (r

é

r

é

chet doi

t

ê

tre collect

é

t

s

é

par

é

r

m

ent par un centre de collect

e

et de traitement s

p

é

cifique. Veuillez vous r

é

r

f

é

f

é

s locales pour conna

î

a

tre ces centres. Ceci

îî

é

enne

.

Questo prodotto

è

soggetto alle disposizioni RAEE (Rifiuti di apparecchiature elettriche ed elettroniche)

.

à

ritirato da un centro incaricato del ritiro e smaltimento. Per conoscere il

à

n

ome del centro pertinente, contattare le autori

t

à

locali. Questa disposizione

à

è

valida solamente i paes

i

d

el

l

’

U.

E

.

é

ctrico y Elect

r

ó

n

ico en materia d

e

ñ

ado se

r

á

í

fico

í

de colecc

i

ó

í

ó

n

Europea

.

Dieses Produkt unterliegt den Bestimmungen zur Entsorgung von elektrischen und elektronische

n

G

er

ä

tes

ä

getrennt vom Hausm

ü

m

ll bei Ihrer

ö

r

tlichen

M

ü

ö

ä

ndiges Abfall-Amt. Dieser

ää

Hinweis gilt nur f

ü

f

rL

ä

nder der Europ

ää

ä

ischen Union

.

д

анног

о

п

о

и

.

,

.

Э

т

и

п

р

авил

а

Ев

р

опейског

о

.

NOTICE

1-1

English

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

INSTALLATION MANUAL

CEILING CASSETTE SPLIT TYPE AIR CONDITIONER

MODEL

COOLING ONLY HEAT PUMP

Part No.:A08019025503

IM-CKA-0501(2)-McQuay

CK20AR / MCK020AR

SL20CR / MLC020CR

4SL20BR / M4LC020BR

5CK20AR / M5CK020AR

5SL20CR / M5LC020CR

CK25AR / MCK025AR

SL25CR / MLC025CR

4SL25BR / M4LC025BR

5CK25AR / M5CK025AR

5SL25CR / M5LC025CR

CK30AR / MCK030AR

SL28CR / MLC028CR

SL30CR / MLC030CR

4SL30CR / M4LC040CR

5CK30AR / M5CK030AR

5SL28CR / M5LC028CR

5SL30CR / M5LC035CR

CK40AR / MCK040AR

SL40CR / MLC040CR

4SL40CR / M4LC040CR

5CK40AR / M5CK040AR

5SL35CR / M5LC035CR

5SL40CR / M5LC050CR

CK50AR / MCK050AR

SL50CR / MLC050CR

4SL50CR / M4LC050CR

5CK50AR / M5CK050AR

5SL50CR / M5LC050AR

CK20A / MCK020A

SL20C / MLC020C

4SL20B / M4LC020B

5CK20A / M5CK020A

5SL20C / M5LC020C

CK25A / MCK025A

SL25C / MLC025C

4SL25B / M4LC025B

5CK25A / M5CK025A

5SL25C / M5LC025C

CK30A / MCK030A

SL28C / MLC028C

SL30C / MLC030C

4SL30C / M4LC040C

5CK30A / M5CK030A

5SL28C / M5LC028C

5SL30C / M5LC035C

CK40A / MCK040A

SL40C / MLC040C

4SL40C / M4LC040C

5CK40A / M5CK040A

5SL35C / M5LC035C

5SL40C / M5LC040C

CK50A / MCK050A

SL50C / MLC050C

4SL50C / M4LC050C

5CK50A / M5CK050A

5SL50C / M5LC050C

1-2

CONTENTS

- Outline And Dimensions page i – iv

- Safety Precautions page 2

- Installation Diagram page 3

- Installation Of The Indoor Unit page 4

- Installation Of The Outdoor Unit page 6

- Refrigerant Piping Work page 7

- Electrical Wiring Connection page 8

-

Special Precautions When Dealing With R410A Unit

page 11

-

Special Precautions When Dealing With R407C Unit

page 11

- Vacuuming And Charging page 11

SAFETY PRECAUTIONS

Before installing the air conditioner unit, please read the following safety precautions carefully.

! Warning

• Installation and maintenance should be performed by qualified persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with the national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard due to insulation failure.

• All electrical wiring must not touch the refrigerant piping or any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before installing or servicing the unit.

- Special Precautions When Charging Unit With

Copeland Scroll Compressors page 12

- Accessory Parts page 13

- Indicator Lights page 13

- Overall Checking page 14

- Standard Operation Conditions page 15

- Auto Random Re-start Function page 15

- Service And Maintenance page 15

- Troubleshooting page 16

- Phase Sequencer (Optional) page 16

! Caution

Please take note of the following important points when installing.

• Do not install the unit where leakage of flammable gas may occur.

If gas leaks and accumulates around the unit, it may cause fire ignition.

• Ensure that the drainage piping is connected properly.

If the drainage piping is not connected properly, it may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged. Overcharge will cause over-current or damage to the compressor.

• Ensure that the units panel is closed after service or installation.

Unsecured panels will cause the unit to operate noisily.

1-3

English

Indoor unit

Outdoor unit

Drain Hose

Front Panel

Air Filter

(behind the grille)

Air Discharge Louver

IR Receiver

LED Light

Air Intake Grille

Refrigerant Piping

Air Intake

Air Discharge

Wireless Remote Control

Air Discharge Louver

Remote Control

INSTALLATION DIAGRAM

Outdoor unit

Drain Hose

Front Panel

Air Filter

(behind the grille)

Air Discharge Louver

Air Intake Grille

Air Discharge Louver

Refrigerant Piping

Air Intake

Air Discharge

Remote Control

Wired Remote Control

Air Intake

Indoor unit

1-4

INSTALLATION OF THE INDOOR UNIT

Preliminary Site Survey

• Electrical supply and installation is to conform to local authority's (e.g. National Electrical Board) codes and regulations.

• Voltage supply fluctuation must not exceed

+

10% of rated voltage. Electricity supply lines must be independent of welding

transformers which can cause high supply fluctuation.

• Ensure that the location is convenient for wiring, piping and drainage.

• The indoor unit must be installed in such that is free from any obstacles in path of cool air discharge and warm air return,

and must allow spreading of air throughout the room (near the center of the room).

• Must be provide clearance for the indoor unit from the wall and obstacles as shown in the figure.

• The installation place must be strong enough to support a load 4 times the indoor unit weight to avoid amplifying noise and

vibration.

• The installation place (hanging ceiling surface) must be assuring levelness and the height in the ceiling is 350mm or more.

• The indoor unit must be away from heat and steam sources (avoid installing it near an entrance).

Unit Installation

• Measure and mark the position for the hanging rod. Drill

the hole for the angle nut on the ceiling and fix the hanging

rod.

• The installation template is extended according to

temperature and humidity. Check on dimensions in use.

• The dimensions of the installation template are the same

as those of the ceiling opening dimensions.

• Before ceiling laminating work is completed, be sure to

fit the installation template to the indoor unit.

NOTE

Be sure to discuss the ceiling drilling work with the

installers concerned.

• Confirm the pitch of the hanging rod is 790mm × 620.5mm

sharp.

• Hold the unit and hang it on the hanging rod with the nut

and washer.

• Adjust the unit height to 35.0 mm between the indoor unit

bottom surface and the ceiling surface.

• Confirm with a level gauge that the unit is installed

horizontally and tighten the nut and bolt to prevent unit

falling and vibration.

• Open the ceiling board along the outer edge of the paper

installation template.

Unit Hanging

Min. 0.5 m Min. 0.5 m Min. 0.5 m

Max. 0.3 m

Max. 3.0 m

Min. 1.0 m

Floor

Obstacle

Beam

35.0 mm

Ceiling

Board

Indoor Unit

890.0 mm (Ceiling board opening)

790.0 mm (Hanging rod)

Unit size 820.0 mm

890.0 mm (Ceiling board opening)

620.5 mm (Hanging rod)

Unit size 820.0mm

Unit

Piping Direction

1-5

English

Main Drain Pipe

Feed Water

Flexible Drain Hose

Drain Test

NOTE

This Indoor Unit uses a drain pump for condensed water drainage. Install the unit horizontally to prevent water

leakage or condensation around the air outlet.

Indoor Unit

Pipe Clamp

Good

Bad

Drain Piping Work

• Drain pipe must be in downward gradient for smooth

drainage.

• Avoid installing the drain pipe in up and down slope to

prevent reversed water flow.

• During the drain pipe connection, be careful not to exert

extra force on the drain connector at indoor unit.

• The outside diameter of the drain connection at the

flexible drain hose is 20mm.

• Be sure to execute heat insulation (polyethylene foam

with thickness more than 8.0mm) on the drain piping to

avoid the condensed water dripping inside the room.

• Connect the main drain pipe to the flexible drain hose.

• Feed water from flexible drain hose to check the piping

for leakage.

• When the test is completed, connect the flexible drain

hose to the drain connector on the indoor unit.

• The front panel can only be fitted in one direction, follow the piping direction. (Follow piping arrow sticker on front

panel)

• Be sure to remove the installation template before installing the front panel.

Panel Installation

Open

Screw

• Open the air intake grille by pulling back the catchers and removing it together with filter from panel.

• Install the front frame panel onto the indoor unit by 4 screws and tighten it completely to prevent cool air leakage.

• Connect the LED wire and air swing wire to the indoor unit.

• The air swing connector must put inside the control box after connected.

From

Front

Panel

LED Wire

Air Swing Wire

Control Box

1-6

Indoor Unit

Cool

Air

Ceiling Board

Panel

Air Leak

Good Installation

Bad Installation

NOTE

Install the front frame panel firmly to prevent cool air leakage which will cause condensation and water dripping.

Cool

Air

Air Leak

Ceiling Board

Panel

Air intake grille installation

• Before installing the air intake grille, be sure to fix the ionizer

filter to the air filter.

• Install the air intake grille together with the air filter to the

front panel.

• The grille can be fit in any direction, when selecting direction,

the ceiling design and grille operability should be considered.

• If the unit comes with ionizer filter (optional item), make

sure to fix the ionizer filter to the air filter before installing

the air intake grille.

• Fix the ionizer filter to the air filter with the black side on top

and white side at bottom.

• Carefully clip on the ionizer filter frame.

Frame

(Optional Item)

Ionizer Filter

(Optional Item)

Filter

(Standard)

INSTALLATION OF THE OUTDOOR UNIT

Preliminary site survey

• A place protected from rain, direct sunlight and well-ventilated wherever practicable.

• A place capable of bearing the weight of the outdoor unit and isolating noise and vibration.

• A place where there are no obstruction of air flow into or out the unit.

• Do not put any object which may become obstacle for the air flow into or out the outdoor unit.

• The location must not be susceptible to high concentration dust, oil, salt or sulfide gas.

SL series A B C D

Min. distance (mm) 300 1000 300 500

Outdoor unit installation

• Install the outdoor unit firmly and horizontally. Maintain a space clearance from the obstruction as shown in below for

servicing and air ventilation.

AB

C

D

1-7

English

REFRIGERANT PIPING WORK

Refrigerant piping is important in particular. Refrigeration cycle of the split air conditioner is realized

by the perfect piping work.

Piping length and elevation

If the piping is too long, both the capacity and reliability of unit will drop. As the number of bends increase, resistance to

flow of refrigerant system increases, thus lowering cooling capacity and as a result the compressor may become defective.

Always choose the shortest path and follow the recommendation as tabulated below.

Piping Connection

• Do not use contaminated or damaged copper tubing. If any piping, evaporator or condenser had been exposed or had been

opened for 15 seconds or more, then vacuum and purge with field supplied refrigerant. Generally, do not remove plastic,

rubber plugs and brass nuts from the valves, fittings, tubing and coils until it is ready to connect suction or liquid line into

valves or fittings.

• If any brazing work is required, ensure that nitrogen gas is passed through coil and joints while the brazing work is being

done. This will eliminate soot formation on the inside wall of copper tubings.

• Cut the pipe stages by stages, advancing the blade of pipe cutter slowly. Extra force and a deep cut will cause more

distortion of pipe and therefore extra burr.

• Remove burrs from cut edges of pipes with a remover. This will avoid unevenness on the flare face which will cause gas

leak.

• Align the center of the piping and sufficiently tighten the flare nut with fingers. Finally, tighten the flare nut with torque

wrench until the wrench clicks.

• Be sure to execute heat insulation. (polyurethane form with thickness more than 15 mm)

• Except the outdoor unit which is pre-charge with refrigerant R22, the indoor unit and the refrigerant connection pipes must

be purged because the air that contain moisture remaining in the refrigerant cycle may cause malfunction to the compressor.

Model 5SL20C/CR 5SL25C/CR 5SL28C/CR 5SL35/40/50C/CR

Max. length (m) 15 15 15 35

Max. elevation (m) 88810

Max. no. of bends 10 10 10 10

Liquid pipe size 1/4” 1/4” 3/8” 3/8”

Gas pipe size 1/2” 5/8” 5/8” 5/8”

Model 4SL20B/BR SL20C/CR 4SL25B/BR SL25C/CR SL30C/CR SL40C/50C/CR

Max. length (m) 15 15 35 35

Max. elevation (m) 8 8 10 10

Max. no. of bends 10 10 10 10

Liquid pipe size 1/4” 3/8” 3/8” 3/8”

Gas pipe size 5/8” 5/8” 5/8” 3/4”

1-8

ELECTRICAL WIRING CONNECTION

CK20A / CK25A & CK30A

Model Indoor CK20A CK25A CK30A

Outdoor SL20B/20C SL25B/25C SL28C/30C

Voltage range** 220-240V/1Ph/50Hz +

!

or 208-230V/1Ph/60Hz+

!

Recommended fuse* (A) 16 20 25

Power supply cable size* (mm

2

) 2.5 2.5 4.0

Number of conductors 333

Interconnection cable size* (mm

2

) 2.5 2.5 2.5

Number of conductors 334

COMP

L

N

COMP

N

Interconnection Cable

Indoor Unit

Terminal

Block

Outdoor Unit

Terminal

Block

There must be a double pole switch with

minimum 3mm contact gap and fuse/circuit

breaker as recommended in the fixed

installation circuit.

CK20A / 25A <> SL20B / 25B / 20C / 25C

CK30A <> SL28C

Power

Supply

Cable

!

COMP

L

N

L

N

L

N

CK30A <> SL30C

Interconnection Cable

Indoor Unit

Terminal

Block

Outdoor Unit

Terminal

Block

There must be a double pole switch with minimum

3mm contact gap and fuse/circuit breaker as

recommended in the fixed installation circuit.

Power Supply Cable

!

Cooling Only

IMPORTANT: *These values are for information only. They should be checked and selected to comply with local and/or

national codes and regulations. They are also subject to the type of installation and size of conductors.

** The appropriate voltage range should be checked with label data on the unit. ETL listed is only applica-

ble to 60Hz power supply only.

Additional Charge (In gram)

The refrigerant is pre-charge in the outdoor unit, but additional charge of refrigerant after vacuuming is necessary. Follow

the recommendation as tabulated below.

Cooling Only (R22)

10m 15m 20m 25m 30m 35m

CK20A 40 110 - - - -

CK25A 90 270 - - - -

CK30A/40A/50A 120 380 640 900 1150 1410

Cooling Only (R407C)

10m 15m 20m 25m 30m 35m

CK20A 40 110 - - - -

CK25A 80 260 - - - -

CK30A/40A/50A 120 360 600 840 1090 1330

Cooling & Heatpump (R410A)

10m 15m 20m 25m 30m 35m

5CK20/25A/AR 30 100 - - - -

5CK30/40/50A/AR 80 230 390 550 710 870

Heatpump (R22)

10m 15m 20m 25m 30m 35m

CK20AR 40 110 - - - -

CK25AR 90 270 - - - -

CK30AR/40AR/50AR

90 280 460 650 830 1020

Heatpump (R407C)

10m 15m 20m 25m 30m 35m

CK20AR 40 110 - - - -

CK25AR 80 260 - - - -

CK30AR/40AR/50AR

80 260 430 610 780 960

1-9

English

CK40A & CK50A

Model Indoor 5CK30/40A CK40A CK50A

Outdoor 5SL35C SL40C SL50C

Voltage range** 380-420V/3Ph /50Hz+ N+

!

or 208-230V/3Ph/60Hz+N+

!

Recommended fuse* (A) 10/20 16/25

Power supply cable size* (mm

2

) (50/60Hz) 1.5/2.5 2.5/4.0

Number of conductors 55

Interconnection cable size* (mm

2

) (50/60Hz) 1.5/1.5 1.5/1.5

Number of conductors 44

COMP

L

N

COMP

L

N

S

R

T

N

There must be a double pole switch with minimum

3mm contact gap and fuse/circuit breaker as

recommended in the fixed installation circuit.

CK40A / CK50A <> SL40C / SL50C

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

Power Supply Cable

!

CK20AR / CK25AR / CK30AR

Model Indoor CK20AR CK25AR CK30AR

Outdoor SL20BR/20CR SL25BR/25CR SL28CR/30CR

Voltage range** 220-240V/1Ph/50Hz+

!

or 208-230V/1Ph/60Hz+

!

Recommended fuse* (A) 16 20 25

Power supply cable size* (mm

2

) 2.5 2.5 4.0

Number of conductors 333

Interconnection cable size* (mm

2

) 2.5 2.5 2.5

Number of conductors 556

There must be a double pole switch with minimum

3mm contact gap and fuse/circuit breaker as

recommended in the fixed installation circuit.

4WV

OF

N1

L

N2

COMP

4V

OF

N

COMP

CK20AR / 25AR <>

SL20BR / 25BR

SL20CR / 25CR

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

Power

Supply

Cable

!

Outdoor Coil Sensor

Heat Pump

IMPORTANT : * These values are for information only. They should be checked and selected to comply with local and/or

national codes and regulations. They are also subject to the type of installation and size of conductors.

** The appropriate voltage range should be checked with label data on the unit.

1-10

N

L

OF

A

4WV

COMP

N

OF

4WV

COMP

N

L

E

CK40AR & CK50AR

Model Indoor 5CK30/40AR CK40AR CK50AR

Outdoor 5SL35CR SL40CR SL50CR

Voltage range** 380-420V/3Ph/50Hz +N+

!

or 208-230V/3Ph/60Hz+N+

!

Recommended fuse* (A) 10/20 16/25

Power supply cable size* (mm

2

) 1.5/2.5 2.5/4.0

Number of conductors 55

Interconnection cable size* (mm

2

) 1.5/1.5 1.5/1.5

Number of conductors 77

A

4WV

OF

N

L

COMP

A

R

S

T

4WV

OF

N

L

COMP

CK40AR / CK50AR <> SL40CR / SL50CR

Outdoor Coil Sensor

Indoor Unit

Terminal

Block

Interconnection

Cable

Outdoor

Unit

Terminal

Power Supply

Cable

!

There must be a double pole switch with minimum

3mm contact gap and fuse/circuit breaker as

recommended in the fixed installation circuit.

CK30AR <> SL28CR

There must be a double pole switch with

minimum 3mm contact gap and fuse/circuit

breaker as recommended in the fixed

installation circuit.

Outdoor Coil Sensor

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

Power Supply Cable

!

CK30AR <> SL30CR

N

L

E

N

L

OF

A

4WV

COMP

N

L

N

L

OF

A

4WV

COMP

Interconnection Cable

Outdoor Coil Sensor

Indoor Unit

Terminal

Block

Outdoor Unit

Terminal

Block

There must be a double pole switch with minimum

3mm contact gap and fuse/circuit breaker as

recommended in the fixed installation circuit.

!

1-11

English

SPECIAL PRECAUTIONS WHEN DEALING WITH R410A UNIT

R410A is a new HFC refrigerant which does not damage the

ozone layer. The working pressure of this new refrigerant is

1.6 times higher than conventional refrigerant (R22), thus

proper installation / servicing is essential.

• Never use refrigerant other than R410A in an air condi-

tioner which designed to operate with R410A.

• POE oil is used as lubricant for R410A compressor, which

is different from the mineral oil used for R22 compressor.

During installation or servicing, extra precaution must be

taken not to expose the R410A system too long to moist

air. Residual POE oil in the piping and components can

absorb moisture from the air.

• To prevent mischarging, the diameter of the service port

on the flare valve is different from that of R22.

SPECIAL PRECAUTIONS WHEN DEALING WITH R407C UNIT

• R407C is a zeotropic refrigerant mixture which has zero

ozone depletion potential and thus conformed to the

Montreal Protocol regulation. It requires Polyol ester oil

(POE) oil for its compressor's lubricant. Its refrigerant

capacity and performance are about the same as the re-

frigerant R22.

• POE oil is used as lubricant for R407C compressor, which

is different from the mineral oil used for R22 compressor.

During installation or servicing, extra precaution must be

taken not to expose the R407C system too long to moist

air. Residual POE oil in the piping and components can

absorb moisture from the air.

• Refrigerant R407C is more easily affected by dust of mois-

ture compared with R22, make sure to temporarily cover

the ends of the tubing prior to installation.

• Use tools and materials exclusively for refrigerant R410A.

Tools exclusively for R410A are manifold valve, charging

hose, pressure gauge, gas leak detector, flare tools, torque

wrench, vacuum pump and refrigerant cylinder.

• As an R410A air conditioner incurs higher pressure than

R22 units, it is essential to choose the copper pipes cor-

rectly. Never use copper pipes thinner than 0.8mm even

though they are available in the market.

• If the refrigerant gas leakage occurs during installation /

servicing, be sure to ventilate fully. If the refrigerant gas

comes into contact with fire, a poisonous gas may occur.

• When installing or removing an air conditioner, do not

allow air or moisture to remain in the refrigerant cycle.

• No additional charge of compressor oil is permitted.

• No other refrigerant other than R407C.

• Tools specifically for R407C only (must not be used for

R22 or other refrigerant).

i) Manifold gauge and charging hose

ii) Gas leak detector

iii) Refrigerant cylinder/charging cylinder

iv) Vacuum pump c/w adapter

v) Flare tools

vi) Refrigerant recovery machine

• Filter-dryer must be installed along the liquid line for all

R407C air conditioners. This is to minimise the contamina-

tion of moisture and dirt in the refrigerant system. Filter-

dryer must be of molecular sieve type. For a heat-pump sys-

tem, install a two-way flow filter dryer along the liquid line.

VACUUMING AND CHARGING

Vacuuming is necessary to eliminate all moisture and air from the system. The series II Outdoor Unit is provided with flare

valve fittings.

Vacuuming

Before vacuuming, perform leak check for refrigeration

circuit. After the system piping are properly connected,

connect the flexible hoses to the correct charging nipples as

shown in the diagram. Ensure that flexible hose from charging

nipples are connected to the vacuum pump via standard

servicing valves and pressure gauges (gauge manifold).

Vacuum the air conditioner system to at least 500 microns

Hg. Do not start the unit when the system is engaged in

vacuuming.

Charging

Before charging, the vacuum must be held at 500 microns

Hg for at least 15 minutes, then break vacuum by charging

R-22 refrigerant. Operate the unit for 15 minutes and ensure

the refrigerant charges is of correct by monitoring running

current, gas and liquid line pressures. Suction and discharge

pipe pressure should be in the region of 75 psig and 275 psig

generally.

After ensuring the system is correctly charged, remove

flexible hose from charging nipples and replace caps.

1-12

A

SPECIAL PRECAUTIONS WHEN CHARGING UNIT WITH

COPELAND SCROLL COMPRESSORS

These precautions are intended for use with Copeland Scroll compressors only with R22, R407C, R134A, R404A, R507 and

R410A refrigerants but are not applied to Copeland reciprocating compressors or competitive Scroll compressors.

Scroll compressors have a very high volumetric efficiency and quickly pump a deep vacuum if there is insufficient refrigerant

in the system or if refrigerant is added too slowly. Operation with low suction pressure will quickly lead to very high discharge

temperatures. While this process is happening, the scrolls are not being well lubricated – scrolls depend on the oil mist in the

refrigerant for lubrication. A lack of lubrication leads to high friction between the scroll flanks and tips and generates additional

heat. The combination of heat of compression and heat from increased friction is concentrated in a small localized discharge

area where temperatures can quickly rise to more than 300˚C. These extreme temperatures damage the Scroll spirals and the

orbiting Scroll bearing. This damage can occur in less than one minute especially on larger compressors. Failure may occur in

the first few hours or the damage done during field charging may show up some time later.

Other typical field charging problems include undercharging, overcharging, moisture or air in the system etc. In time each one

of these problems can cause compressor failure.

Minimal equipment is required for field charging. The minimum equipment required to do a satisfactory job is:-

Set of service gauges Vacuum gauge

Hoses Scales

Vacuum pump Thermometer

The proper refrigerant charge should follow the volume as recommended by manufacturer and recommendation should be

followed by the installer.

1. Charging procedures – Single phase compressors

Evacuate the system to 500 microns Hg. (67Pa). To reduce evacuation time, use short, large diameter hoses and connect to

unrestricted service ports on the system. Quality of vacuum cannot be determined by time – a reliable vacuum gauge must

be used. (etc. electronic vacuum gauge)

Turn the refrigerant cylinder upside down, purge the charging hose and charge liquid through the liquid line charging port

until refrigerant no longer flows or until the correct charge has been weighed in. If additional charge is required start the

system and slowly bleed liquid into the suction side until the system is full.

Copeland recommends charging liquid in a CONTROLLED manner into the suction side until the system is full.

This recommendation does not hold true for reciprocating compressors where liquid charging into the suction side could

cause severe damage.

Carefully monitor the suction and discharge pressures – ensure that the suction pressure does not fall below 25 psig (1.7

bar) at any time during the charging process.

• Manifold Gauge will show cylinder pressure rather than suction pressure if the cylinder valve and Manifold

valve “A” are both open.

! Caution

There are many ways of charging liquid in a “controlled manner” into the suction

side:-

1. Use valve A on the manifold gauge set

2. Use the valve on the refrigerant cylinder

3. Charge through a Shredder valve

4. Use a hose with a Shredder valve depressor

5. Charge into the suction side at some distance from the compressor

6. All of the above

2. Charging procedures – Three phase compressors

The fundamental procedure is the same as for single phase models but the compressor can run in the wrong direction on

starting. If this happens reverse any two phases and start again. Short term reverse rotation will not damage the compressor.

All Specter compressors (Model: ZR90 to ZR19M) have internal discharge temperature protectors which are very effective

in preventing dangerously high discharge temperatures during charging. The protection module will trip and lock the

compressor out for 30 minutes. It is not normally necessary to wait 30 minutes for the module to reset. When the compressor

has cooled down the module can be reset by breaking the power supply to the control circuit. Very often the serviceman

does not understand why the module tripped and uses a jumper wire to bypass it. He continues to charge the system and

removes the jumper when charging is complete. The compressor may or may not run with the protector back in the circuit

but it is certain that the compressor has been damaged and premature failure is inevitable.

1-13

English

Short Duct Specification

• The indoor unit is provided with air discharge and air intake “knock-out” hole for duct connection. However the connec-

tion of the short duct for air discharge is possible on only one side.

• The use of short duct for air discharge will improve airflow distribution if there is an obstruction (such as a lighting fixture)

or in a long, narrow room or an L-shaped room. It also use for air conditioning of two rooms simultaneously.

ACCESSORY PARTS

Possible Opening Dimension For Duct Connection

Air Discharge Knock Out Hole

Air Intake

Knock Out Hole

Possible Direction For Air Discharge And Air Intake

Air Intake

Air DischargeAir Discharge

Air Discharge Air Discharge

NOTE

• Avoid using the short duct on which the air discharge grille can be completely closed, to prevent evaporator freezing.

• In order to prevent condensation forming, be sure that there is sufficient thermal insulation and no leakage of cool

air when installing the short duct.

• Keep the introduction of fresh air intake within 20% of total air flow. Also provide a chamber and use a booster fan.

Sealing Material

• It is possible to seal one of the four air discharge outlet. (sealing two or more air discharge outlet could cause a malfunction)

• Remove the front panel and insert the sealing material into the air discharge outlet on the indoor unit to seal the air outlet.

• The sealing material is the same length as the longer air discharge outlet. If it is desired to seal the shorter air discharge

outlet, cut the sealing material to shorten it.

• Push the sealing material in about 10 mm beyond the bottom surface of the indoor unit so that it does not touch the air

louver. Be sure not to push the sealing material in any farther than about 10 mm.

10

50 50 50 50 50 10

207020109

119 90

Ø100

PCD Ø140

115 20 115

INDICATOR LIGHTS

Remote Control

When there is infrared remote control operating signal, the signal receiver on indoor unit will made a <beep> for signal

acceptance confirmation.

1-14

OVERALL CHECKING

• Ensure that :-

1) The unit has been mounted solidly and rigid in position.

2) Piping and connections are leak proof after charging.

3) Proper wiring has been installed.

• Drainage check – pour some water into the main drain pipe from the flexible drain hose.

• Test run

1) Conduct a test run after water drainage test and gas leakage test.

2) Check the following items :-

a. Is the electric plug firmly inserted into the socket ?

b. Is there any abnormal sound from the unit ?

c. Is there any abnormal vibration on the unit itself or piping ?

d. Is the drainage of water smooth ?

• Confirm that :

1) Condenser fan is running, with warm air blowing off the condensing unit.

2) Evaporator blower is running and discharge cool air.

3) The remote control incorporate a 3 minute delay in the circuit. Thus, it requires about 3 minutes before the outdoor

condensing unit can start up.

LED

Faulty Indication Action

POWER TIMER SLEEP/HEAT Other LEDs

Blink 1 time - - Blink Fan Room Sensor Open or Short

Blink 2 times - - Blink Dry & Fan Indoor Coil Sensor Open

Blink 3 times - - Blink Dry Outdoor Coil Sensor Open

Compressor Overload /

- Blink 1 time - Blink Cool Indoor Coil Sensor Short / Call Your Dealer

Outdoor Coil Sensor Short

- Blink 3 times - Blink Cool & Dry Gas Leak

- Blink 2 times - Blink Cool & Fan Water Pump Fault

1-15

English

AUTO RANDOM RE-START FUNCTION

If there is a power cut when the unit is operating, it will automatically resume the same operating mode when the power is

restored. (Applicable only to units with this feature)

! Caution

Before turning off the power supply, set the remote controller's ON/OFF switch to the “OFF”

position to prevent the nuisance tripping of the unit.

If this is not done, the unit's fans will start turning automatically when power resumes,

posing a hazard to service personnel or the user.

SERVICE AND MAINTENANCE

Service parts

Indoor air filter

Indoor unit

! Caution

Do not operate any heating apparatus too close to the air conditioner unit. This may cause

the plastic panel to melt or deform as a result of the excessive heat.

Maintenance procedures

1. Remove any dust adhered on the filter by using a vacuum cleaner or

wash in lukewarm water (below 40ºC) with neutral cleaning detergent.

2. Rinse well and dry the filter before placing it back onto the unit.

3. Do not use gasoline, volatile substances or chemical to clean the filter.

1. Clean any dirt or dust on the grille or panel by wiping it using soft cloth

soaked in lukewarm water (below 40ºC) with neutral detergent solution.

2. Do not use gasoline, volatile substances or chemical to clean the indoor

unit.

Period

At least once every

2 weeks. More

frequently if

necessary.

At least once every

2 weeks. More

frequently if

necessary.

STANDARD OPERATION CONDITIONS

• Disconnect from the main power supply before servicing the air conditioner unit.

• DO NOT pull out the power cord when the power is ON. This may cause serious

electrical shocks which may result in fire hazards.

! Warning

Heat Pump Unit

Cooling unit

Temperature Ts °C / °F Th °C / °F

Minimum indoor

19.4 / 66.9 13.9 / 57.0

temperature

Maximum indoor

26.7 / 80.1 19.4 / 66.9

temperature

Minimum outdoor

19.4 / 66.9 13.9 / 57.0

temperature

Maximum outdoor

46 / 114.8 24 / 75.2

temperature

Ts: Dry bulb temperature. Th: Wet bulb temperature.

Temperature Ts °C / °F Th °C / °F

Minimum indoor

10 / 50 –

temperature

Maximum indoor

26.7 / 80.1 –

temperature

Minimum outdoor

-8 / 17.6 -9 / 15.8

temperature

Maximum outdoor

24 / 75.2 18 / 64.4

temperature

La page charge ...

McQuay A Series Guide d'installation

McQuay A Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents