Hestan Outdoor Side Burner Le manuel du propriétaire

OUTDOOR COOKING

Outdoor Side Burner

AGB

Use & Care Manual

Installation & Operation

HESTAN OUTDOOR, MOST

POWERFUL, VERSATILE

AND RELIABLE OUTDOOR

COOKING AVAILABLE.

EN

1

Message from Hestan:

Outdoor cooking is a perfectionist’s pursuit, and with your new investment,

you’ve now taken the ultimate step forward. We sincerely welcome you to

the Hestan Family. We’ve engineered and built our products so that your

guests will rave about your meal, but deep down, our customers know it

could’ve been just a little more tender, juicier – a pinch more salt in the rub

or a few seconds less on the flame. Yes, we’ve taken the time to know our

Hestan customer and we’re excited to be on this journey with you. Hestan

Outdoor was born from this same perfectionist passion. Our engineers

experimented, innovated, tweaked and tinkered until they created the most

powerful, versatile and reliable outdoor products available.

We pride ourselves on restless innovation, superior engineering and

purpose-built designs, but also our in-depth understanding of our target

consumer and the interests and needs of the ultimate end-users we serve

and covet. For many consumers, cooking outdoors is much more than an

act of food preparation. It’s a lifestyle activity that encompasses culinary,

leisure and social pursuits among others.

We are thankful and proud that you have chosen Hestan, and we yearn to

have you as a customer for life. We take your decision to choose Hestan

most seriously, and we promise to deliver the very best to you.

Welcome to Hestan Outdoor

EN

2

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Do not try lighting this appliance without reading the LIGHTING

INSTRUCTIONS section of this manual.

For outdoor use ONLY. This cooking appliance is not intended to be

installed in or on recreational vehicles, and/or boats.

Flammable Gas - disconnect all propane or natural gas supplies to this

unit before servicing.

Electrical Parts & Components – disconnect all power supplies and

batteries before servicing.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

DANGER

1. Do not store or use gasoline or

other flammable liquids or vapors

in the vicinity of this or any other

appliance.

2. An LP cylinder not connected

for use shall not be stored in

the vicinity of this or any other

appliance.

READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE USING YOUR

SIDE BURNER TO REDUCE THE RISK OF FIRE, BURN HAZARD, OR OTHER

INJURY. KEEP THIS MANUAL FOR FUTURE REFERENCE.

EN

3

4 MODEL NUMBERS

5 RATING LABELS

5 PRECAUTIONS

8 REGULATORY / CODE REQUIREMENTS

8 PORTABLE LP CYLINDERS

9 LOCATION AND ASSEMBLY

9 INSTALLATION

13 GAS AND ELECTRICAL CONNECTIONS

21 LIGHTING INSTRUCTIONS

23 USING YOUR SIDE BURNER

23 CLEANING AND MAINTENANCE

26 TROUBLESHOOTING

27 WIRING SCHEMATICS

31 PARTS LIST

31 SERVICE

31 WARRANTY

TABLE OF CONTENTS

EN

4

BUILT-IN MODELS

Model No. Description

AGB121-NG / -LP 12” BUILT-IN SINGLE SIDE BURNER

AGB122-NG / -LP 12” BUILT-IN DOUBLE SIDE BURNER

AGB121

AGB122

MODEL NUMBERS

EN

5

RATING LABEL

The rating label contains important information about your Hestan appliance such as the model

and serial number, gas type and manifold pressure, the BTU rating for each burner type, and the

minimum installation clearances.

PRECAUTIONS - BEFORE YOU USE YOUR SIDE BURNER

When properly cared for, your Hestan Side Burner will provide safe, reliable service for many

years. However, extreme care must be used since the Side Burner produces intense heat, which

can cause serious injury or even death if the instructions are not followed carefully. When using

this appliance, basic safety practices must be followed as outlined below.

1. NEVER LEAVE THE SIDE BURNER UNATTENDED WHILE COOKING.

2. Children should not be left alone or unattended in an area where the Side Burner is being

used. Never allow them to sit, stand, or play on or around the Side Burner. Do not store

items of interest to children around or below the Side Burner or in the cart. Never allow

children to crawl inside of the cart.

3. Never operate the Side Burner while under the influence of alcohol or drugs.

4. Never use the Side Burner in windy conditions. If located in a consistently windy area,

oceanfront, mountaintop, etc., a windbreak will be required. Always adhere to the specified

clearances as described in the INSTALLATION section of this manual.

5. The Side Burner shall be used only outdoors and shall not be used in buildings, garages, sheds,

breezeways, or any enclosed areas. Do not operate the Side Burner under unprotected,

combustible construction. Use only in well-ventilated areas. See the INSTALLATION section

of this manual.

6. Do not use the Side Burner unless a leak check has been performed on all gas connections.

See the GAS CONNECTIONS section of this manual.

7. If the Side Burner is installed by a professional installer or technician, be sure that they show

you where your gas supply shut-off is located. All gas lines must have a shut-off that is easily

accessible. If you smell gas, check for leaks immediately. Check only with a soap and water

solution. Never check gas leaks with an open flame. See the GAS CONNECTIONS section

of this manual.

Hestan Outdoor Side Burner rating label is located on the inside rear wall of the

unit, behind the control panel.

EN

6

8. Check the regulator, hoses, burner ports, and venturi / valve section carefully. Always turn

off gas at the source (tank or supply line) prior to inspecting parts.

9. When lighting a burner, always pay close attention to what you are doing. Be certain you

are turning the correct knob labeled for the burner you intend to use. If any burner does not

light, or goes out during operation, turn off all gas control knobs, and wait five (5) minutes

before attempting to re-light. See the LIGHTING INSTRUCTIONS section of this manual.

10. Portable LP cylinders - Always shut off the main valve on the liquid propane (LP) cylinder

after each use. Never use a dented or rusted LP cylinder. Never attach or disconnect an LP

cylinder, or move or alter gas fittings when the Side Burner is in operation or is hot.

11. Inspect LP gas supply hose prior to each use of the Side Burner. The hose must be kept away

from heated areas of the Side Burner. If there is evidence of excessive abrasion or wear, or

the hose is cut, it must be replaced before using the Side Burner. The hose and LP regulator

are supplied as a complete assembly and must be replaced together. Do not attempt to repair

or replace the hose itself. Contact your Hestan dealer for genuine replacement P/N 014309.

12. Keep any electrical supply cord away from the heated areas of the Side Burner. The cord is

provided with a 3-prong grounding plug which should not be removed or altered. Do not

use this appliance with an ungrounded, 2-prong adapter. The cord must be plugged into a

properly grounded GFCI-protected outlet. See INSTALLATION section of this manual.

13. Spiders and insects like to nest in the burners, venturis, valves, and orifices of a Side Burner,

disrupting the gas flow in the burner. This very dangerous condition can cause a fire

behind the control panel, damaging the Side Burner and risking personal injury. If your Side

Burner has been unused for a long time, inspect and clean the burners, venturis, valves, and

orifices. It is recommended you inspect your Side Burner at least twice a year. See BURNER

ADJUSTMENT section of this manual for details.

14. Keep the areas surrounding the Side Burner free from combustible materials, trash, or

combustible fluids and vapors such as gasoline or charcoal lighter fluid. Do not obstruct the

flow of combustion gases and ventilation airways (front).

15. If your Side Burner is mounted on a grill cart, keep the rear area free and clear of debris, extra

LP cylinders, etc. Do not block the ventilation louvers of the cart.

16. If your Side Burner is mounted on a cart and stored indoors, ensure that it is cool before

moving. If propane is used, the LP cylinder must be disconnected and stored OUTSIDE in a

well-ventilated area, out of the reach of children. A grill cover which covers the entire Grill +

Side Burner is recommended, even when stored indoors.

17. Never move the Side Burner when hot. When in use, portions of the Side Burner are hot

enough to cause severe burns.

18. Always have an “ABC” type fire extinguisher accessible – never attempt to extinguish a grease

fire with water or other liquids.

19. Avoid wearing loose-fitting garments or long sleeves while cooking with the Side Burner.

They could ignite. For personal safety, wear proper apparel while cooking. Some synthetic

fabrics are highly flammable and should not be worn while cooking.

20. Never let pot holders, covers, or other flammable materials come in contact with or too close

to any cooking grate, burner, or hot surface until it has cooled down sufficiently. Fabrics

may ignite and result in personal injury. Use only dry potholders. Moist or damp potholders

on hot surfaces may cause burns from steam. Do not use a towel or bulky cloth in place of

potholders. Do not let potholders touch hot portions of the cooking grates.

21. Never touch the cooking grates or immediate surrounding metal surfaces with your bare

hands while cooking with the Side Burner, as these areas become extremely hot and could

cause burns. Use only the handles and knobs provided for operation of the Side Burner.

PRECAUTIONS - BEFORE YOU USE YOUR SIDE BURNER

(continued)

EN

7

22. Protect your hands with an insulated glove or mitt when operating the Side Burner. Always

keep your face away and open lids slowly on pots and pans to allow heat and steam to escape

before fully opening. Never lean over an open hot Side Burner.

23. The Side Burner metal cover must be removed while lighting. Leaving the cover in place

while lighting can result in an explosion and personal injury, or death. Never lean over a

Side Burner or look directly into the burner when attempting to light. See the LIGHTING

INSTRUCTIONS section of this manual.

24. Do not heat unopened food containers (cans) as pressure build-up will cause the container to

explode.

25. Do not use aluminum foil to line the burner bowl or the drip tray. This will alter the airflow

to the burner or trap excessive heat in the control area. This can melt control knobs, wiring,

or igniters, and increase the risk of personal injury. Such damage is specifically excluded from

our warranty.

26. Never use the Side Burner without the drip tray in place and pushed all the way to the back.

Without the drip tray, hot grease or oil from a spill-over can leak downward creating a fire or

explosion hazard.

27. Grease is extremely flammable. Let hot grease cool before attempting to handle or dispose

of it. Avoid letting excessive grease deposits collect by cleaning the drip tray often. Never

clean while the Side Burner is on, or hot from recent use.

28. Cooking excessively fatty meats and oils will cause flare-ups or grease fires. Damage caused

by them or by the Side Burner being left unattended, are not covered under the terms and

conditions of our warranty.

29. Only certain types of glass, heatproof glass-ceramic, earthenware, or other glazed utensils

are suitable for Side Burner use. However, these types of materials may break with sudden

temperature changes. Use only on low or medium heat settings, and according to their

manufacturers’ directions.

30. Do not lean on side shelves or place a load of more than 25 lbs (11.3 kg) on a side shelf.

31. Do not repair or replace any part of the Side Burner unless specifically recommended in this

manual. All other warranty and non-warranty service should be referred to and performed by

a qualified technician.

32. For proper lighting and performance of the burners, keep the ports clean. It is necessary

to clean them periodically for optimum performance. The burners will operate only in one

position and must be mounted correctly for safe operation. See BURNER ADJUSTMENT

section of this manual.

33. Clean the Side Burner with caution. Avoid steam burns - do not use a wet sponge or cloth

to clean the Side Burner while it is hot. Some cleaners produce noxious fumes or can

ignite when applied to a hot surface. Be sure all Side Burner controls are turned off and

the appliance is cool before using any type of aerosol cleaner on or around the appliance.

The chemical that produces the spraying action could, in the presence of heat, ignite or

cause metal parts to corrode. Clean and perform general maintenance on the Side Burner

twice a year. Watch for corrosion, cracks, or insect activity. See the CLEANING AND

MAINTENANCE section of this manual.

PRECAUTIONS - BEFORE YOU USE YOUR SIDE BURNER

(continued)

EN

8

REGULATORY / CODE REQUIREMENTS

Installation of this cooking appliance must be made in accordance with local codes. In the

absence of local codes, this unit should be installed in accordance with the National Fuel Gas

Code

ANSI Z223.1/NFPA 54

, Natural Gas and Propane Installation code

CSA B149.1

, or Propane

Storage and Handling Code

B149.2

.

All Electrical Components must be electrically grounded in accordance with local codes or in the

absence of local codes with the National Electrical Code

ANSI/NFPA 70

, or Canadian Electrical

code

CSA C22.1

.

STATE OF MASSACHUSETTS

Massachusetts requires all gas be installed using a plumber or gas fitter carrying the appropriate

Massachusetts license. All permanently installed natural gas or propane installations require a T

handle type manual gas valve be installed in the gas supply line to this appliance. This does not

apply to portable propane installations using a 20lb. cylinder.

CALIFORNIA PROPOSITION 65 - WARNING

The burning of gas cooking fuel generates toxic by-products, which are on the list of substances

which are known by the State of California to cause cancer or reproductive harm. California law

requires businesses to warn customers of potential exposure to such substances. To minimize

exposure to these substances, always operate this unit according to the use and care manual,

ensuring you provide good ventilation when cooking with gas. This warning is issued pursuant to

California Health & Safety Code Sec. 25249.6.

PORTABLE LP GAS CYLINDERS

Use only a standard 20 lb. (9.1kg) liquid propane (LP) gas cylinder - 12.25” diam. X 18.25” H

(31cm X 47cm) which features an Overfill Protection Device. The cylinder must be installed in

the upright position. Do not use a dented or rusty LP cylinder as it may be hazardous and should

be checked by your LP supplier. Never use a cylinder with a damaged valve. Never move or alter

the gas fittings. Check the expiration date on the cylinder collar as well. Do not refill an expired

cylinder, it must be replaced. If you buy refilled (exchange) LP cylinders, check this date as well.

The LP gas cylinder must be constructed and marked in accordance with the specifications for

LP gas cylinders of the U.S. Department of Transportation (DOT). The cylinder must be provided

with a shut off valve terminating in an LP gas supply cylinder valve outlet specified, as applicable,

for connection type QCC1 in the standard for compressed gas cylinder valve outlet and inlet

connections ANSI/CGA-V-I.

Certain liquid propane dealers may fill LP cylinders for use in the Grill / Side Burner beyond

cylinder filling capacity. This “overfilling” may create a dangerous condition due to a build-up of

excess pressure. As a safety device, there is a pressure relief valve which will vent propane gas

vapor to relieve this excess pressure. This vapor is combustible and therefore can be ignited. To

reduce this danger, you should take the following safety precautions:

1. When you have your cylinder filled, be sure you tell the supplier to fill it to no more than 80%

of its total capacity.

2. If you own or use a spare cylinder, you should NEVER store it near or under the grill/cart unit

or burner box, or near any other ignition or heat source (like a water heater or furnace).

IF THE INFORMATION IN 1 AND 2 ABOVE IS NOT FOLLOWED EXACTLY, A FIRE

CAUSING DEATH OR SERIOUS INJURY MAY OCCUR.

3. The LP cylinder must be disconnected and stored OUTSIDE in a well-ventilated area, out of

the reach of children.

4. Do not store a full cylinder in direct sunlight.

EN

9

LOCATING AND ASSEMBLING THE SIDE BURNER

When determining a suitable location for your Side Burner, take into account concerns such as

exposure to wind, rain, sprinklers, proximity to traffic paths, and keeping any gas supply line runs

as short as possible.

Locate the Side Burner only in a well-ventilated area. Never locate the Side Burner in a building,

garage, breezeway, shed or other such enclosed areas without an approved ventilation system.

Never locate the Side Burner over, under, or next to unprotected combustible construction.

Using the Side Burner in windy areas can disrupt the flame, especially on low or simmer settings.

This may cause nuisance sparking of the igniter. Relocate to a less windy area. If the Side Burner

is mounted in an enclosure (island), you may need to build a wind-break to avoid this issue in the

future.

When installing a Side Burner or other gas appliance into an enclosure (island), the enclosure

must be constructed with ventilation openings to avoid accumulation of gas should there be a

leak. See the INSTALLATION section of this manual for details. Keep the area underneath the

Side Burner free of debris.

Ensure all packaging, straps, etc. have been removed from the Side Burner. Remove any tie-down

wires from the burners.

Keep the area underneath the Side Burner free

of debris. If your Side Burner is mounted on a

cart, engage the brakes on the casters to prevent

movement of the cart.

Ensure that the burner cap is mounted correctly

on the burner ring. Do not operate the Side

Burner without the burner cap in place (see Fig. 1).

Figure 1

INSTALLATION

CLEARANCES - NON-COMBUSTIBLE:

TO NON-COMBUSTIBLE CONSTRUCTION ABOVE THE COOKING SURFACE

A minimum of 4” (10 cm) clearance from the rear of the appliance to non-combustible

construction is required. See diagrams on the following pages.

TO NON-COMBUSTIBLE CONSTRUCTION BELOW THE COOKING SURFACE

The appliance may installed directly on non-combustible construction. See diagrams on the

following pages.

CLEARANCES - COMBUSTIBLE:

TO COMBUSTIBLE CONSTRUCTION ABOVE THE COOKING SURFACE

A minimum of 12” (30 cm) clearance on the sides and the rear of the appliance to combustible

construction is required. Read warning below. See diagrams on the following pages.

TO COMBUSTIBLE CONSTRUCTION BELOW THE COOKING SURFACE

The appliance may installed directly on combustible construction. See diagrams on the following

pages.

The minimum clearances to combustible materials means that ALL combustible materials must be

outside this 12” (30 cm) zone. As an example, if you have an island with a stucco or tiled surface

and wood-frame construction, the wood is considered combustible, even though the Side Burner

is touching the stucco or tile surface, which is non-combustible. In extreme circumstances, the

wood could potentially get hot enough to burn. Examples of other combustible materials are

EN

10

BUILT-IN DIMENSIONS (NON-COMBUSTIBLE):

INSTALLATION

(continued)

compressed wood, plant fibers (bamboo), vinyl/plastic, or other materials capable of being ignited

and burned. Materials that are flame-proofed or treated with flame-retardant are still considered

combustible.

VENTILATION OPENINGS

A minimum of three 10 in² (65 cm²) of ventilation openings must be provided for both left and

right sides of your enclosure (island), as well as the back. These openings are required to safely

dissipate gas vapors if there is a leak in your enclosure. See diagram below.

EN

11

INSTALLATION

(continued)

BUILT-IN INSTALLATION

Your Hestan Side Burner comes ready to install into your enclosure (island). Proceed to the GAS

CONNECTIONS section for further instruction.

INSTALLATION OF SIDE BURNER ONTO

GRILL CART (MODEL AGB122 ONLY -

REQUIRES PANEL KIT AGBPK)

It is possible to mount your Hestan Side Burner

to your grill cart. You will need to order Panel

Kit AGBPK, available from your Hestan dealer.

Instructions are provided with the kit.

BUILT-IN DIMENSIONS (COMBUSTIBLE):

Hestan delivers

the consistent

control

EN

13

GAS AND ELECTRICAL CONNECTIONS

GAS SUPPLY

The local gas authority or supplier should be consulted at the installation planning stage in order

to establish the availability of an adequate supply of gas (NG or LP). If it is a new installation,

have the gas authorities or supplier check the meter size and piping to assure that the unit is

supplied with the necessary amount of gas supply and pressure to operate the unit(s).

Gas connections should be made by a qualified plumber, or your professional outdoor appliance

installer.

All fixed (non-mobile) appliances must be fitted with an accessible upstream gas shutoff valve as

a means of isolating the appliance for emergency shut off and for servicing.

Make certain new piping and connections have been made in a clean manner and have been

purged so that piping compound, chips, etc. will not clog regulators, valves, orifices, or burners.

Use pipe joint compound / thread sealant approved for natural and LP gases.

NEVER CONNECT THE SIDE BURNER TO AN UNREGULATED GAS SUPPLY. Before

proceeding, ensure the appliance is fitted for Natural or Liquid Propane gas. Connecting to an

improper gas type will result in poor performance and increased risk of damage or injury. Gas

type and gas consumption (BTU per hour) for each burner type is shown on the rating label

affixed to the underside of the drip tray.

Installation of this cooking appliance must be made in accordance with local codes. In the

absence of local codes, this unit should be installed in accordance with the National Fuel Gas

Code No.

Z223.1/ NFPA 54

, Natural Gas and Propane Installation code

CSA B149-1,

or Propane

Storage and Handling Code

B149.2.

NOTE: See rating label for manifold pressure for the type of gas of your appliance.

CONVERSION KITS

Gas conversion kits are available from your Hestan dealer should you need to convert an LP unit

to NG, or vice-versa.

HIGH ALTITUDE KITS

If you live in a high altitude area, 2,000 ft. (610 m) or more above sea level, your Side Burner will

require different orifices for proper combustion and performance. High altitude kits are available

through Hestan Customer Service. Please have your model and serial number information ready

when you call.

EN

14

GAS CONNECTION - NATURAL GAS (NG)

NOTE: To ensure proper heating performance of this appliance, verify that the gas line supply

pressure is adequate. Use only the gas pressure regulator supplied with this appliance. This

regulator is set for a supply pressure of 7 inch WC (1.74 kPa) to maintain 4 inch WC (1.00 kPa)

outlet (manifold) pressure. Use a minimum 1/2” ID flex hose to prevent gas starvation. Ensure

that the service pipe supplying the side burner is fitted with a shut-off valve conveniently

positioned and easily accessible as an emergency gas shut-off.

Your Hestan Side Burner for use with Natural Gas is supplied with its own regulator which

MUST be installed. If this regulator needs to be replaced, use only the type specified by Hestan

for this appliance.

To connect the regulator follow the next steps:

1. Locate the regulator mounted underneath your Side Burner.

2. Connect gas supply using a minimum 1/2” diameter flexible (semi–rigid) stainless steel gas

hose, no more than 48” (1.22m) in length. If you plan to inter-connect the Side Burner with

your Hestan Grill, be sure to use the fittings supplied with the mounting kit, and a flexible

hose as short as possible to make the connection. The hose as well as the connectors must

comply with the

Standard for Connectors for Outdoor Gas Appliances and Manufactured

Homes, ANSI Z21.75 • CSA 6.27

, and suitable for outdoor installation. Use the appropriate

thread sealant on all connections.

3. Proceed to LEAK TESTING section.

1/2” ID FLEX HOSE,

ELBOW & NIPPLE

(SUPPLIED BY

CUSTOMER)

NAT GAS

REGULATOR

INCOMING

NAT GAS SUPPLY

SHUTOFF VALVE

(SUPPLIED BY

CUSTOMER)

HESTAN SIDE BURNER

(MODEL AGB122-NG SHOWN)

GAS AND ELECTRICAL CONNECTIONS

(continued)

EN

15

GAS CONNECTION - LP PIPED SYSTEMS

An LP piped system is one with a large central LP tank that feeds an entire household. These

systems are normally equipped with a high pressure regulator by the large LP tank, and low

pressure regulators close to the home. The gas line connectors must comply with the

Standard

for Connectors for Outdoor Gas Appliances and Manufactured Homes, ANSI Z21.75 • CSA 6.27

,

and suitable for outdoor installation. The connection shall be 48” (1.22 m) or less.

NOTE: To ensure proper heating performance of this appliance, verify that the gas line supply

pressure is adequate. The regulator must be set for a supply pressure of 11.0” WC (2.74 kPa) to

maintain 10.0” WC (2.49 kPa) outlet (manifold) pressure. Use a minimum 1/2” ID flex hose to

prevent gas starvation. Ensure that the service pipe supplying the Side Burner is fitted with a

shut-off valve conveniently positioned and easily accessible as an emergency gas shut-off.

1/2” ID FLEX HOSE,

ELBOW & NIPPLE

(SUPPLIED BY

CUSTOMER)

CONVERTIBLE

LP GAS

REGULATOR

INCOMING

LP GAS SUPPLY

SHUTOFF VALVE

(SUPPLIED BY

CUSTOMER)

HESTAN SIDE BURNER

(MODEL AGB122-LP SHOWN)

GAS AND ELECTRICAL CONNECTIONS

(continued)

Your Hestan Side Burner for use with an LP Piped System is supplied with its own convertible

regulator which MUST be installed. If this regulator needs to be replaced, use only the type

specified by Hestan for this appliance.

To connect the regulator follow the next steps:

1. Locate the regulator mounted underneath your Side Burner.

2. Connect gas supply using a minimum 1/2” diameter flexible (semi–rigid) stainless steel gas

hose, no more than 48” (1.22 m) in length. If you plan to inter-connect the Side Burner with

your Hestan Grill, be sure to use the fittings supplied with the mounting kit, and a flexible

hose as short as possible to make the connection. The hose as well as the connectors must

comply with the

Standard for Connectors for Outdoor Gas Appliances and Manufactured

Homes, ANSI Z21.75 • CSA 6.27

, and suitable for outdoor installation. Use the appropriate

thread sealant on all connections.

3. Proceed to LEAK TESTING section.

EN

16

GAS AND ELECTRICAL CONNECTIONS

(continued)

GAS CONNECTION - LIQUID PROPANE (LP) CYLINDER

Should you wish to connect your Hestan Side Burner to a standard 20 lb. LP gas cylinder, you

will need to order kit AGCKLPT. This kit includes a two-stage regulator/hose assembly for

connection to the tank, and a tank retention device. This regulator/hose assembly must be used

WITHOUT alteration. If this assembly needs to be replaced, contact your Hestan dealer for

genuine replacement P/N 014309.

NOTE: To ensure proper heating performance of this appliance, verify that the supply pressure is

adequate. Use only the gas pressure regulator supplied with this appliance. This regulator is set

to maintain 10 inch WC (2.49 kPa) outlet (manifold) pressure.

To connect the regulator / hose assembly follow these steps:

1. Locate the regulator and gas connection point in the rear right side of your Side Burner (in cart-

mounted models, remove the rear panel to gain access).

2. Connect the 3/8” Flare (compression flare fitting) X 1/2” NPT female adapter as shown. Then

connect the regulator/hose assembly to the adapter as shown. Use appropriate thread sealant

on all connections.

3. Connect the regulator/hose assembly to a standard 20 lb. LP cylinder. If you plan to inter-

connect the Double Side Burner with your Hestan Grill, you will need Panel Kit AGBPK (as seen

page 11). Be sure to use the included fittings and a flexible hose as short as possible to make the

connection. The hose as well as the connectors must comply with the

Standard for Connectors

for Outdoor Gas Appliances and Manufactured Homes, ANSI Z21.75 • CSA 6.27

, and suitable for

outdoor installation. Use the appropriate thread sealant on all connections.

4. Proceed to LEAK TESTING section.

2-STAGE LP

REGULATOR /

HOSE ASSEMBLY

20 lb. LP TANK

(SUPPLIED BY CUSTOMER)

ADAPTER, 3/8 FLARE

X 1/2 NPT FEMALE

(SHIPPED LOOSE)

HESTAN SIDE BURNER

(MODEL AGB122-LP SHOWN)

ELBOW & NIPPLE

(SUPPLIED BY CUSTOMER)

RETENTION

DEVICE

(SHIPPED LOOSE)

EN

17

LP TANK RESTRAINT

If you purchased a Hestan Grill with Side Burner on a cart, be sure to restrain the LP cylinder by

securing it with the retention bolt on the slide-out tray as shown below. It is important the tank

does not fall over or stretch the hose which could cause a gas leak.

LEAK TESTING

GENERAL

Although all gas connections on your Hestan Side Burner are leak tested at the factory prior to

shipment, a complete gas tightness check must be performed at the installation site due to possible

movement in shipment, or excessive pressure unknowingly being applied to parts of the unit.

Periodically check the whole system for leaks, or immediately check if the smell of gas is detected.

BEFORE TESTING

• Do not smoke while leak testing.

• Never leak test with an open flame.

• Make a soap solution of one part liquid detergent and one part water for leak testing purposes.

• Apply the solution to the gas fittings by using a spray bottle or a brush.

• For LP units, always check with a full LP cylinder.

2-STAGE

LP REGULATOR /

HOSE ASSY.

TANK

RETENTION

BOLT

SLIDE-OUT

TANK TRAY

20 LB.

LP TANK

(SUPPLIED BY

CUSTOMER)

GAS AND ELECTRICAL CONNECTIONS

(continued)

EN

18

To Test

• Make sure all control valves are in the “OFF” position.

• Apply the soap solution described above to all fittings.

• Turn the gas supply on.

• Check all connections from the supply line, or LP cylinder up to and including the manifold

pipe assembly and all connections to each burner.

• Soap bubbles will appear where a leak is present. If a leak is present, immediately turn off gas

supply, tighten any leaking fittings, turn the gas supply back on, and recheck.

• If you cannot stop a gas leak, turn off the gas supply and call the dealer where you purchased

your Side Burner.

• Do not use the Side Burner until all connections have been checked and do not leak.

IMPORTANT NOTE - ALWAYS CHECK FOR LEAKS AFTER EVERY LP CYLINDER CHANGE.

If a leak is present, or if there is evidence of excessive abrasion or wear, or the hose is cut, it must

be replaced before using the Side Burner. The hose and LP regulator are supplied as a complete

assembly and must be replaced together. Do not attempt to repair or replace the hose itself.

Contact your Hestan dealer for genuine replacement P/N 014309.

Check all gas supply fittings for leaks before each use. It is handy to keep a spray bottle of soapy

water near the shut-off valve of the gas supply line. Spray all the fittings. Bubbles indicate leaks.

ELECTRICAL SUPPLY

Important: This appliance must be electrically grounded in accordance with local codes, or in the

absence of local codes with the National Electrical Code,

ANSI/NFPA 70-1990

.

Appliances equipped with a flexible electrical supply cord are provided with a three-prong

grounding plug. It is imperative that this plug be connected to a properly grounded three-prong

receptacle. If the receptacle is not the proper grounding type, contact an electrician. Do not

remove the grounding prong from this plug.

The Side Burner is designed for 120 volt AC power and must be plugged into a Ground Fault

Circuit Interrupter (GFCI) protected circuit. Do not connect the Side Burner to the electrical

supply until after gas connections have been made and leak checks have been performed.

KEEP ANY ELECTRICAL CORD AND FUEL SUPPLY HOSE AWAY FROM ANY HEATED

SURFACES.

1. To protect against electric shock, do not immerse cord or plugs in water or other liquid.

2. Unplug from the outlet when not in use and before cleaning. Allow to cool before putting

on or taking off parts.

3. Do not operate any outdoor cooking gas appliance with a damaged cord or plug, or after the

appliance malfunctions or has been damaged in any manner. Contact the manufacturer for

repair.

4. Do not let the cord hang over the edge of a table or touch hot surfaces.

5. Do not use an outdoor cooking gas appliance for purposes other than intended.

6. Use only a Ground Fault Circuit Interrupter (GFCI) protected circuit with this outdoor

cooking gas appliance.

GAS AND ELECTRICAL CONNECTIONS

(continued)

La page charge ...

Hestan Outdoor Side Burner Le manuel du propriétaire

Hestan Outdoor Side Burner Le manuel du propriétaire

dans d''autres langues

Documents connexes