Allen-Bradley 2755-HUG-9 Manuel utilisateur

User

Manual

Hand-Held

Undecoded Bar

Code Scanner

Cat. No. 2755-HUG-4,

2755-HUG-9

Allen-Bradley

Publication 2755-6.1

Important User Information

Because of the variety of uses for the products described in this publication,

those responsible for the application and use of this control equipment must

satisfy themselves that all necessary steps have been taken to assure that each

application and use meets all performance and safety requirements, including

any applicable laws, regulations, codes and standards.

The illustrations, charts, sample programs and layout examples shown in this

guide are intended solely for purposes of example. Since there are many

variables and requirements associated with any particular installation,

Allen-Bradley does not assume responsibility or liability (to include intellectual

property liability) for actual use based upon the examples shown in this

publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,

Installation, and Maintenance of Solid-State Control (available from your local

Allen-Bradley office), describes some important differences between solid-state

equipment and electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part,

without written permission of Allen-Bradley Company, Inc., is prohibited.

Throughout this manual we use notes to make you aware of safety

considerations:

!

ATTENTION: Identifies information about practices or

circumstances that can lead to personal injury or death,

property damage or economic loss.

Attention statements help you to:

• identify a hazard

• avoid the hazard

• recognize the consequences

Important: Identifies information that is critical for successful application and

understanding of the product.

Table of Contents

Publication 2755-6.1

Preface

Intended Audience P–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents of this Manual P–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Related Publications P–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Laser Warning Symbol P–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 1 Scanner Features

Scanner Features 1–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LED Indicators 1–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety Labels 1–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scanning Ranges 1–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Standard Range Scanner (Catalog No. 2755-HUG-4) 1–6. . . . . . . .

Extended Range Scanner (Catalog No. 2755-HUG-9) 1–7. . . . . . .

Accessories 1–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2 Connecting and Operating Scanner

Compatible Decoders 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scanner Cable 2–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting the Scanner to a Decoder 2–3. . . . . . . . . . . . . . . . . . . . .

Operating the Scanner 2–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Spotter Beam 2–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Automatic Shutoff 2–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Audible Response 2–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Tips 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

toc–ii

Publication 2755-6.1

Chapter 3 Troubleshooting and Maintenance

Troubleshooting the Scanner 3–2. . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning the Scan Window 3–4. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

Appendix A

Connector Pinouts

Appendix B

European Union Directive Compliance

Appendix C

Glossary

Preface

Publication 2755-6.1

Using this Manual

Read this preface to familiarize yourself with the rest of the manual.

This preface covers the following topics:

• intended audience

• chapter contents

• laser warning symbol

• related publications

Intended Audience

No special knowledge is required to understand this document or to use

the scanner. Undecoded scanners require a decoder. We assume that you

are familiar with the operation and cable inputs to your decoder.

P–2

Publication 2755-6.1

Contents of this Manual

The following table briefly describes the contents of each section.

Chapter Title Contents

Preface Using this Manual

Describes the purpose, background, and scope

of this manual. Also provides a list of related

publications.

1 Scanner Features

Overview of the scanner. Includes read range

charts and description of accessory items.

2

Connecting and Operating

the Scanner

Describes how to connect the scanner to a

decoder. Operating tips are also provided.

3

Troubleshooting and

Maintenance

Provides solutions to the most common

operating problems. Also includes instructions

on cleaning the scan window.

Appendix A Specifications

Provides physical, electrical and environmental

specifications.

Appendix B

Scanner Connector

Pinouts

Provides scanner pinout signal names and a

brief description of each.

Appendix C

European Union

Compliance Directives

Lists requirements for use of scanner within the

European Union.

Glossary

Provides definitions for commonly used

terminology.

Inside Back

Cover

Bar Code Test Symbols

Sample symbols useful for testing the operation

of your bar code system.

P–3

Publication 2755-6.1

Related Publications

Below is a list of related publications you may need to refer to when

using the scanners.

Publication No. Title

2755-921

Bar Code Basics

Describes bar code symbologies, equipment, and typical applications.

2755-833

User Manual for

DS/DD Series B Enhanced Decoders

2755-ND010

User Manual for

Single-Head Enhanced Decoder (Catalog No. 2755-DS1A)

2755-ND011

User Manual for

Dual-Head Enhanced Decoder (Catalog No. 2755-DD1A)

2755-2.37

Product Data Sheet for

Bulletin 2755 Gun Adapter (Catalog No. 2755-NC16)

Laser Warning Symbol

Be aware of the following laser caution symbols.

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

680nm LASER

1.0 MILLIWATT MAX OUTPUT

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEAU

APPAREIL A LASER DE CLASSE 2

LASER–STRAHLUNG

NICHT IN DEN STRAHL BLICKEN !

LASER KLASSE 2

Chapter 1

Publication 2755-6.1

Scanner Features

This chapter describes the features of the standard and extended range,

undecoded scanners. Included are descriptions of:

• major features

• LEDs

• scanning ranges

• safety labels

• accessories

1–2

Publication 2755-6.1

Scanner Features

The scanners use a low power visible (red) laser diode for scanning. The

trigger turns on the laser which scans a label at approximately 36 scans

per second.

Trigger

Cable Connector

LEDs

The laser beam:

-exits through the scan window

-reflects off the label back through the window

-is detected by a sensor in the scanner

When a label is read, the laser beam is automatically turned off until the

trigger is pressed again. If no label is read, the laser beam automatically

turns off after approximately 3 seconds and remains off until the trigger

is released and pressed again.

Note: The Extended Range Scanner (Catalog No. 2755-HUG-9) has a

two position trigger. The first detent provides a spotter beam and the

second position provides a scan line.

1–3

Publication 2755-6.1

LED Indicators

On the back of the scanner there is a clear window through which two

LEDs are visible.

Green

Red

Green LED = Good Read, indicating that a bar code symbol has been

scanned and decoded. LED remains on until the next scan

(trigger pressed).

Red LED = Scanning, indicating that the laser light is on.

1–4

Publication 2755-6.1

Safety Labels

The scanners use a low power visible laser diode. As with any bright

light source, you should avoid staring directly into the beam.

Momentary exposure to a CDRH Class II laser is not known to be

harmful.

The following figure shows the location of all safety labels as they

appear on the scanner.

AVOID EXPOSURE

LASER LIGHT IS

EMITTED FROM

THIS APERATURE.

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

680nm LASER

1.0 MILLIWATT MAX OUTPUT

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEAU

APPAREIL A LASER DE CLASSE 2

LASER–STRAHLUNG

NICHT IN DEN STRAHL BLICKEN !

LASER KLASSE 2

COMPLIES WITH

IEC 825–1:1993/EN 60825

CAUTION – LASER LIGHT WHEN OPEN –

DO NOT STARE INTO BEAM.

ATTENTION – RAYONNEMENT LASER EN

CAS DOUVERTURE. NE PAS REGARDER

DANS LE FAISCEAU

VORSICHT!

LASERSTRAHL, WENN ABDECKUNG GEOEFFNET

Appears on both sides.

1–5

Publication 2755-6.1

Scanning Ranges

The scanners can read bar code symbols at various distances depending

upon the bar code symbol density (width of narrow bars or spaces). The

following table lists the read ranges for both the standard and extended

range scanners.

Minimum

Symbol

Density

Standard Range

(Catalog No. 2755-HUG4)

Inches / Centimeters

Extended Range

(Catalog No. 2755-HUG9)

Inches / Meters

5.0 mil

(.13 mm)

1.25 in to 2.7 in

(3.2 cm to 6.9 cm)

Not Applicable

7.5 mil

(.19 mm)

1.0 in to 7.0 in

(2.5 cm to 17.8 cm)

5.0 in to 11 in

(0.13 m to 0.28 m)

10.0 mil

(.25 mm)

Data Not Available

4.0 to 13 in

(0.10 m to 0.33 m)

15.0 mil

(.38 mm)

Data Not Available

4.0 to 60 in

( 0.10 m to 1.52 m)

20.0 mil

(.51 mm)

1.0 in to 27 in

(2.5 cm to 69 cm)

5.0 to 65 in

(0.13 m to 1.65 m)

40.0 mil

(1.02 mm)

4.5 in to 37 in

(11.4 cm to 94 cm)

14 in to 120 in

(0.36 m to 3.05 m)

55.0 mil

(1.40 mm)

7 in to 50 in

(17.8 cm to 127 cm)

24 in to 156 in

(0.61 m cm to 3.96 m)

70.0 mil

(1.78 mm)

Reflective

Not Applicable

96 in to 276 in

2.43 m to 7.01 m

100 mil

(1.02 mm)

Reflective

Not Applicable

96 in to 420 in

(2.44 m to 10.67 m)

1–6

Publication 2755-6.1

0

30 35

0

5 (12.7 cm)

10 (25.4 cm)

40 mil

5 mil

Distance From Front of Scanner

76 89

inches

centimeters

252015

105

7.5 mil

(0.19 mm)

(1.02 mm)

(0.13 mm)

12.7 25 38 51 64

Standard Range Scanner

Catalog No. 2755-HUG4

Scanner

5 (12.7 cm)

10 (25.4 cm)

40

102

55 mil

(1.40 mm)

Scan Width

20 mil

(0.51 mm)

Scanner

50

127

1–7

Publication 2755-6.1

0

300 350

0

25 in (63.5 cm)

50 in (127 cm)

55.0 mil

15.0 mil

Distance From Front of Scanner

762 889

inches

centimeters

250200150

10050

20.0 mil

(0.51mm)

(1.40 mm)

(0.38 mm)

127 254 381 508 635

Extended Range Scanner

Catalog No. 2755-HUG9

Scanner

25 in (63.5 cm)

50 in (127 cm)

420

1067

70.0 mil Reflective

(1.78 mm)

100 mil Reflective

(2.54 mm)

Scan Width

See Inset

Inset

40 mil

(1.02 mm)

Scanner

Scan Width

inches

centimeters

1196

3

7.6 15.2 22.9 27.9

13

33.0

0

1.5 in (3.8 mm)

3 in (7.8cm)

1.5 in (3.8 mm)

7.5 mil

(.19 mm)

10 mil

(0.25 mm)

1–8

Publication 2755-6.1

Accessories

The following accessories are available.

Scanner Cables – Connect scanner to A-B

decoder. See page 2–2 for connections.

• 8 ft. / 2.44 meter

(Catalog No. 2755-HUC-GA1-08)

• 15 ft. / 4.57 meter

(Catalog No. 2755-HUC-GA1-15)

• 20 ft. / 6.1 meter

(Catalog No. 2755-HUC-GA1-20)

Adjustable Stands – Holds scanner at adjustable

angles and heights for hand-free scanner

operation.

• 5 to 18 inch (127 to 457 mm) height

(Catalog No. 2755-HFN-K1)

• 9 to 16 inch (229 to 406 mm) height

(Catalog No. 2755-HFN-K2)

Multi-mount Stand – Rubber-coated, fixed

mount holder for counter or wall mounting.

• (Catalog No. 2755-HFN-K3)

Protective Boot – Heavy canvas boot provides

additional protection for the scanner.

• (Catalog No. 2755-HFN-H1)

Chapter 2

Publication 2755-6.1

Connecting and

Operating Scanner

This chapter describes how to connect and test the operation of the

scanner. Sections include:

• compatible decoding devices

• installing / removing the interface cable

• connecting to a decoder

• operating scanner

Safety

!

ATTENTION: Caution - use of controls or

adjustments or performance of procedures other than

those specified herein may result in hazardous laser

light exposure.

Compatible Decoders

The undecoded scanners are compatible with the following

Allen-Bradley decoders:

• Bulletin 2708-DH5 Attended Workstations

• Multi-Purpose Bar Code WorkStation

(Catalog No. 2755-DH1)

• Single or Dual-Head Enhanced Bar Code Decoder

(Catalog No. 2755-DD1x, -DS1x)

2–2

Publication 2755-6.1

Scanner Cable

The scanner cables connect to the bottom of the scanner handle.

See page 1–8 for lengths available.

Connector

Slot for Locking Collar

Cable Connector

Locking Collar

To attach the scanner cable to the scanner.

1. Pull back the locking collar from the connector.

2. Insert the cable connector into the scanner.

3. Align the tabs on the locking collar with the slots on the handle.

4. Push in and turn the locking collar counterclockwise to lock.

Connector is locked when flat edge of locking collar aligns with the

flat edge of the scanner handle.

Remove a scanner cable by rotating the locking collar clockwise until the

cable can be pulled out of the scanner.

2–3

Publication 2755-6.1

Connecting the Scanner to a Decoder

The scanner interface cable connects to the input port of the decoder.

The following table summarizes the cable and connectors required for

each decoder.

Note: A Gun Adapter (Catalog No. 2755-NC16)

may be required to connect the scanner to some

Series B decoders.

Decoder Type

2755-NC16

Series B

Gun Adapter

Bulletin 2708-DH5

Attended WorkStations

No

Multi-Purpose

Bar Code WorkStation

(Catalog No. 2755-DH1)

No

Single or Dual-Head

Enhanced Bar Code Decoder

(Catalog No. 2755-DS1A, -DD1A)

Required

!

ATTENTION: Do not install or remove the scanner

cables or connectors until the power to the scanner and

decoder is turned off. Failure to follow this caution may

result in damage to the scanner or decoder.

!

ATTENTION: Make sure you use the Series B Gun

Adapter (Catalog No. 2755-NC16, Series B). If you are

ugrading from an earlier version Allen-Bradley hand-held

scanner (such as the 2755-G2 or -G3) which used the

Series A gun adapter, you will need to purchase the series

B gun adapter.

2–4

Publication 2755-6.1

The 2755-NC16 Gun Adapter connects to the decoder input port as

shown below for the Enhanced Decoder, the High Speed Decoder is

similar.

Gun Adapter

2–5

Publication 2755-6.1

Operating the Scanner

1. Check your connections.

• Is the scanner cable securely attached?

• If connecting to a High Speed or Enhanced

decoder, is the Gun Adapter present?

• Is power applied to the decoder?

2. Test the scanner

Aim the scanner at the work

surface and press the trigger.

You should see the red beam

on the work surface, and the

red LED on the back of the

scanner should be on.

3. Scan a label.

Scan a bar code. Adjust the

scanner position so that the scan

beam is centered on the bar

code and overlaps both sides.

When the scanner has read a

symbol:

• You will hear a beep from the

decoder (if enabled).

• The green LED will turn on

and remain on until the next

scan.

La page charge ...

Allen-Bradley 2755-HUG-9 Manuel utilisateur

Ce manuel convient également à

Allen-Bradley 2755-HUG-9 Manuel utilisateur

dans d''autres langues

Autres documents