Simplicity 61E377-0145-J1 Manuel utilisateur

Marque: Simplicity

Modèle: 61E377-0145-J1

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Models:54E000,540000,61E000,610000,61G200, 61G300

Operator's Manual

Manual del operador

Manuel d'utilisation

Revision A

Not for

Reproduction

2 vanguardpower.com

Not for

Reproduction

Not for

Reproduction

General Information

This manual contains safety information so that you will know the hazards and risks

related to this engine and how to prevent them. It also contains instructions for the

correct use and maintenance of the engine. Because Briggs & Stratton does not know

what equipment this engine will power, it is important that you read, understand, and

obey these instructions. Save these original instructions for future reference.

NOTE:The figures and illustrations in this manual are for reference only and can be

different from your model. If you need help, contact an Authorized Service Dealer.

For replacement parts or technical help, record the date of purchase, engine model,

type, trim, and the engine serial number. These numbers are located on your engine.

Refer to the Features and Controls section.

Date of Purchase

Engine Model - Type - Trim

Engine Serial Number

European Office Contact Information

For questions related to European emissions, contact our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage V (5): Carbon

Dioxide (CO2) Values

Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values

of Briggs & Stratton EU Type-Approval Certificate engines.

Recycling Information

Recycle all cartons, boxes, used oil, and batteries as

specified by government regulations.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information about hazards that could

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to

indicate the likelihood and the potential severity of injury. In addition, a hazard symbol

is used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious

injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or moderate

injury.

NOTICE indicates information considered important but not hazard-related.

Hazard Symbols and Meanings

Safety information about

hazards that can result in

personal injury.

Read and understand the

Operator's Manual before

operating or servicing the

unit.

Fire Hazard Explosion Hazard

Shock Hazard Toxic Fume Hazard

Hot Surface Hazard Noise Hazard - Ear

protection recommended

for extended use.

Thrown Object Hazard -

Wear eye protection.

Explosion Hazard

Frostbite Hazard Kickback Hazard

Amputation Hazard -

Moving Parts

Chemical Hazard

Thermal Heat Hazard Corrosive Hazard

Safety Messages

WARNING

This product can expose you to chemicals including gasoline engine exhaust, which is

known to the State of California to cause cancer, and carbon monoxide, which is known

to the State of California to cause birth defects or other reproductive harm. For more

information go towww.P65Warnings.ca.gov.

WARNING

Briggs & Stratton® Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products, see

www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs

& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result

in serious injury or death.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

When you operate the equipment

• Do not tilt the engine or the equipment at an angle which causes fuel to spill.

• Do not choke the carburetor (if equipped) to stop the engine.

• Do not start or operate the engine with the air cleaner (if equipped) or the air

filter (if equipped) removed.

When you do maintenance

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occurand could result a fire or an explosion.

• During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,

if mounted on the engine, is empty and that the spark plug side is up. If the fuel

tank is not empty, leakage can occurand could result a fire or an explosion.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

4 vanguardpower.com

Not for

Reproduction

• Do not change the governor spring, links or other parts to increase engine

speed.

• Do not hit the flywheel with a hammer or hard object. This could result in failure

of the flywheel during operation.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

When you move the location of equipment

• Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the

CLOSED position.

When fuel or equipment is in storage with fuel in the fuel tank

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that

have pilot lights.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Engine start-up causes spark that could result in a fire or explosion.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and windows

for ventilation. After the operation of this product, carbon monoxide can quickly

collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

WARNING

Rotating parts can entangle hands, feet, hair, clothing, or accessories and result

in traumatic amputation or laceration.

• Operate equipment with the guards correctly installed.

• Keep hands and feet away from rotating parts.

• Remove jewelry and make sure that long hair is away from all rotating parts.

• Do not wear loose clothes or items that could become caught.

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

If you smell gas

• Do not start the engine.

• Do not switch on electrical switches.

• Do not use a phone in the vicinity.

• Evacuate the area.

• Contact the gas supplier or the fire department.

Features and Controls

Engine Controls

Compare the callout letters in Figures 1, 2, 3, and 4 to the engine controls in the list that

follows:

A. Engine Identification Numbers Model - Type - Code

B. Spark Plug

C. Cyclonic Air Cleaner

D. Low Profile Air Cleaner

E. Dipstick

F. Oil Fill

G. Oil Filter

H. Oil Drain Plug

I. Oil Pressure Sensor

J. Finger Guard

K. Electric Starter

L. Starter Solenoid

M. Regulator / Rectifier

N. Carburetor - Carburetor Models

O. Oil Cooler (if equipped)

P. Muffler (if equipped)

Q. Fuel Pump

Starter Switch

Throttle Control

ChokeControl(Carburetor Models

)

U. Fuel Filter

V. Tachometer (if equipped)

Some engines and equipment have remote controls. See the equipment manual for the

location and operation of remote controls.

Engine Control Symbols and Meanings

Engine Speed - FAST Engine Speed - SLOW

Not for

Reproduction

Engine Speed - STOP ON - OFF

Engine Start

Choke CLOSED

Engine Start

Choke OPEN

Fuel Cap

Fuel Shut-off OPEN

Fuel Shut-off CLOSED

Fuel Level - Maximum

Do Not Overfill

Operation

Oil Recommendations

Oil Capacity: See the Specifications section.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

We recommend the use of Briggs & Stratton

Warranty Certified oils for best

performance. Other high-quality detergent oils are permitted if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Use the chart to select the best viscosity for the outdoor temperature range expected.

Engines on most outdoor power equipment operate well with 5W-30 Synthetic oil. For

equipment operated in hot temperatures, Vanguard

15W-50 Synthetic oil gives the best

protection.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil

consumption. Checkthe oil level frequently.

C 5W-30

D Synthetic 5W-30

Vanguard

Synthetic 15W-50

Check and Add Oil

Before you check or add oil

• Make sure the engine is level.

• Clean the oil fill area of debris.

• Refer to the Specifications section for oil capacity.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

1. Remove the dipstick (A, Figure 5) and clean with a cloth.

2. Install and tighten the dipstick (A, Figure 5).

3. Remove the dipstick and check the oil level. Make sure that the oil level is at the

top of the full indicator (B, Figure 5) on the dipstick.

4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 5). Do not add

too much oil. After you add oil, wait one minute and check the oil level again. Make

sure that the oil level is correct.

5. Install and tighten the dipstick (A, Figure 5).

Low Oil Protection System (if equipped)

A low oil sensor is installed on some engines. If the oil is low, the sensor will display a

warning light or stop the engine. Stop the engine and follow these steps before you start

the engine.

• Make sure the engine is level.

• Do an oil check. Refer to the Check Oil Level section.

• If the oil level is low, add the correct amount of oil. Start the engine and make

sure the warning light (if equipped) does not come on.

• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton

Authorized Service Dealer to have the oil problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is permitted.

NOTICE

Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or

change the engine to operate on alternate fuels. Use of unapproved fuels could result in

damage to engine components, which will not be repaired under the warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. Refer

to the Storage section. All fuel is not the same. If start or performance problems occur,

change fuel providers or brands. This engine is certified to operate on gasoline. The

emissions control system for carbureted engines is EM (Engine Modifications). The

emissions control systems for engines with electronic fuel injection are ECM (Engine

Control Module), MPI (Multi Port Injection), and if equipped an O2S (Oxygen Sensor).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is permitted.

For carbureted engines, high altitude adjustment is required to maintain performance.

Operation without this adjustment will cause decreased performance, increased fuel

consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service

Dealer for high altitude adjustment information. Operation of the engine at altitudes

below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.

Add Fuel

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.

2. Fill the fuel tank (A, Figure 6) with fuel. Because fuel will expand, do not fill above

the bottom of the fuel tank neck (B).

3. Install the fuel cap.

6 vanguardpower.com

Not for

Reproduction

Start and Stop Engine

Start Engine

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result

in burns or death.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped)

are correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY.

See a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and

windows for ventilation. After the operation of this product, carbon monoxide

can quickly collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers

or dealers could have added oil to the engine. Before you start the engine for the

first time, make sure that the oil is at the correct level. Add oil as specified by the

instructions in this manual. If you start the engine without oil, damage will occur and the

engine will not be repaired under warranty.

Types of Starting Systems

Before you start the engine, you must know the type of starting system on your engine.

Your engine will have one of these types.

• Electronic Fuel Injection (EFI) System: An EFI system does not have a

choke or a primer.

• Choke System: This type of system has a choke to be used in cool

temperatures. Some models will have a separate choke control while others

will have a combination choke and throttle choke. It does not have a primer.

NOTE:Your equipment could have remote controls. Refer to the equipment manual for

location and operation of remote controls.

Electronic Fuel Injection (EFI) System

1. Check the engine oil. See the Check Oil Level section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.

4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate

the engine in the FAST position.

5. Turn the electric start switch (D, Figure 7) to the ON or START position.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Choke System

1. Check the engine oil. See the Check Oil Level section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Move the fuel shut-off (A, Figure 7), if equipped, to the OPEN position.

4. Move the throttle control (B, Figure 7), if equipped, to the FAST position. Operate

the engine in the FAST position.

5. Move the choke control (C, Figure 7), or the combination choke and throttle (B,C) to

the CLOSED position.

NOTE:To start the engine with a dry fuel system, additional cranking time in the choke

position will be required. This will give the fuel pump time to prime the fuel system.

6. Turn the key switch (D, Figure 7) to the ON or START position.

7. If the engine starts but will not continue to operate, move the choke control (C,

Figure 7) to the OPEN position to start the engine.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

8. As the engine warms, move the choke control (C, Figure 7) to the OPEN position.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Stop the Engine

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Do not choke the carburetor (if equipped) to stop the engine.

1. With the throttle control in the SLOW position, turn the electric start switch (D,

Figure 7) to the OFF position. Remove the key and keep it in a safe place out of the

reach of children.

2. After the engine stops, move the fuel shut-off (A, Figure 7), if equipped, to the

CLOSED position.

Maintenance

Maintenance Information

WARNING

During maintenance if it is necessary to tilt the unit, make sure that the fuel tank, if

mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not

empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted

in a different direction, it will not easily start because of oil or fuel contamination of the air

filter or the spark plug.

We recommend that you see a Briggs & Stratton Authorized Service Dealer for all

maintenance and servicing of the engine and engine parts.

NOTICE

All the components used to build this engine must remain in place for correct operation.

WARNING

Accidental engine spark can cause an electric shock or fire and could result in

entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start.)

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

Emissions Control Service

For maintenance, replacement, or repair of emissions control devices and

systems, contact a qualified off-road engine repair establishment or service

technician. However, for "no charge" emissions control service, the work must be done

by a factory authorized dealer. Refer to the Emissions Control Statements.

Not for

Reproduction

Maintenance Schedule

Intervals of 8 Hours or Daily

• Check the engine oil level.

• Clean the area around the muffler and controls.

Intervals of 100 Hours or Annually

•

Clean or replace the air filter

1 2

• Change the engine oil and filter.

• Replace the oil filter (if equipped).

• Replace the spark plugs.

• Check the muffler and spark arrester.

• Service the exhaust system.

Intervals of 250 Hours or Annually

• Check the valve clearance. Adjust if necessary.

Intervals of 400 Hours or Annually

•

Change the air filter

• Replace the fuel filter.

•

Service the air cooling system

•

Clean the oil cooler fins

Intervals of 600 Hours

• Replace the safety filter, if equipped.

In dusty conditions or when airborne debris is present, clean more frequently.

Every third air filter change, replace the inner safety filter (if equipped.

Electronic Fuel Injection (EFI) System

The EFI System monitors engine temperature, engine speed, and battery voltage for

engine start-up and warm-up. There are no adjustments on the system. If start-up or

operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.

NOTICEMake sure to obey the steps that follow or damage to the EFI system could

occur.

• DO NOT start the engine if the battery cables are loose.

• Turn the key to the OFF position before you disconnect, remove, and / or install

the battery.

• DO NOT use a battery charger to start the engine.

• DO NOT disconnect the battery cables during engine operation.

• When you disconnect the battery cables, first connect the positive (+) cable, and

then connect the negative (-) cable to the battery.

• When you charge the battery, turn the ignition switch to the OFF position,and

disconnect the negative (-) battery cable from the battery.

• DO NOT spray water directly on the Electronic Control Module.

Carburetor and Engine Speed

Do not make adjustments to the carburetor or engine speed. The carburetor was set at

the factory to operate satisfactorily under most conditions. Do not change the governor

spring, linkages, or other parts to adjust the engine speed. If any adjustments are

required contact a Briggs & Stratton Authorized Service Dealer for service.

NOTICE

The equipment manufacturer specifies the maximum speed for the engine as installed

on the equipment. Do not exceed this speed. If you are not sure what the equipment

maximum speed is, or what the engine speed is set to from the factory, contact a Briggs

& Stratton Authorized Service Dealer for assistance. For safe and correct operation

of the equipment, the engine speed should only be adjusted by a qualified service

technician.

Servicing the Spark Plug

Check the spark plug gap (A, Figure 8) with a wire gauge (B). If necessary, set the

spark plug gap. Install and tighten the spark plug to the correct torque. For gap or torque

specifications, refer to the Specifications section.

NOTE:In some areas, it is mandatory by local law that you use a resistor spark plug

to decrease ignition signals.If a resistor spark plug was installed by the equipment

manufacturer, use the same type for replacement.

Servicing theExhaust System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Remove debris from the muffler and cylinder area. Examine the muffler for cracks,

corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and

examine for damage or carbon blockage. If damage is found, install the replacement

parts before you operate the equipment.

WARNING

Replacement parts must be of the same design and installed in the same position as the

original parts. Other parts could result in damage or an injury.

Change Engine Oil

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occur and cause a fire or an explosion.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

Used oil is a hazardous waste product and must be discarded of correctly. Do not

discard with household waste. Contact your local authorities, service center, or dealer

for safe disposal or recycling facilities.

Remove Oil

1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 9), and

keep it away from the spark plug(s)(E).

2. Remove the dipstick (A, Figure 10).

3. Remove the oil drain plug (F, Figure 11). Drain the oil into an approved container.

4. Install and tighten the oil drain plug(F, Figure 11).

Change Oil Filter, if equipped

1. Drain the oil from the engine. Refer to the Remove Oil section.

2. Remove the oil filter (H, Figure 12) anddiscard correctly.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.

4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten

the oil filter 1/2 to 3/4 turns.

5. Add oil. Refer to the Add Oil section.

6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.

7. Stop the engine. Make sure thatoil level is at the top of the full indicator (B, Figure

5) on the dipstick.

Add Oil

• Make sure the engine is level.

• Clean the oil fill area of all debris.

• Refer to the Specifications section for oil capacity.

1. Remove the dipstick (A, Figure 10). Remove oil from the dipstick with a clean cloth.

2. Slowly add oil into the engine oil fill (C, Figure 10). Do not overfill. Wait one

minute and then check the oil level.

3. Install and tighten the dipstick (A, Figure 10).

4. Remove the dipstick and check the oil level. The correct oil level is at the top of the

full indicator (B, Figure 10) on the dipstick.

5. Install and tighten the dipstick (A, Figure 10).

8 vanguardpower.com

Not for

Reproduction

6. Connect the spark plug wire(s) (D, Figure 9) to the spark plug(s) (E).

Servicing the Air Filter

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

• Do notstart and operate the engine with the air cleaner assembly (if equipped)

or the air filter (if equipped) removed.

NOTICE

Do not use pressurized air or solvents to clean the filter. Pressurized air could result in

damage to the filter and solvents will dissolve the filter.

See the Maintenance Schedule for service requirements.

Different models will use a foam or a paper filter. Some models could also have an

optional pre-cleaner that can be washed and used again. Compare the illustrations in

this manual with the type installed on your engine and service as follows.

Cyclonic Air Filter

1. Open the fastener(s) (A, Figure 13) and remove the cover (B).

2. Remove the air filter (C, Figure 13).

3. To loosen debris, lightly tap the air filter on a hard surface. If the air filter is dirty,

replace it with a new air filter.

4. To remove the safety filter (D, Figure 13), if equipped, carefully pull it away from the

air cleaner body (E). Make sure that dirt or debris does not go into the engine.

5. Install the new safety filter (D, Figure 13) in the air cleaner body (E).

6. Install the air filter (C, Figure 13) above the safety filter (D).

7. Install the cover (B, Figure 13) and close the fastener(s) (A).

Low Profile Air Filter

1. Remove the fastener(s) (A, Figure 14).

2. Remove the cover (B, Figure 14).

3. Remove the fastener(s) (C, Figure 14) and retainer (D).

4. Remove the air filter (E, Figure 14).

5. Remove the pre-cleaner (F, Figure 14), if equipped, from the air filter (E).

6. To loosen debris, lightly tap the air filter (E, Figure 14) on a hard surface. If the air

filter is dirty, replace with a new air filter.

7. Clean the pre-cleaner (F, Figure 14), if equipped, in liquid detergent and water.

Make sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.

8. Assemble the dry pre-cleaner (F, Figure 14), if equipped, to the air filter (E).

9. Install the air filter (E, Figure 14) with the retainer (D) and fastener(s) (C).

10. Install the cover (B, Figure 14) with the fastener(s) (A). Make sure the fastener(s) is

tight.

Servicing the Cooling System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible debris, such as leaves, grass, and brush can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

NOTICE

Do not use water to clean the engine. Water could cause contamination of the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can stop the air flow and cause the engine to

become too hot and result in unsatisfactory performance and decreased engine life.

1. Use a brush or dry cloth to remove debris from the air intake area (A, Figure 15).

2. Keep linkage, springs, and controls (B, Figures 15, 16) clean.

3. Keep the area around and behind the muffler (C, Figures 15, 16) free of

combustible debris.

4. Make sure the oil cooler fins (D, Figure 15) are free of dirt and debris.

5. Loosen the fastener(s) (E, Figures 15, 16) and remove the debris access panels

(F). Remove grass and debris that has collected on the cylinders.

6. Install the debris access panels (F, Figures 15, 16) and attach with fastener(s) (E).

After a period of time, debris can collect in the cylinder cooling fins and cause the engine

to overheat. This debris cannot be removed without partial disassembly of the engine.

As recommended in the Maintenance Schedule, have a Briggs & Stratton Authorized

Service Dealer inspect and clean the air cooling system.

Servicing the Fuel System

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• Before you clean or replace the fuel filter, drain the fuel tank or close the fuel

shut-off valve.

• If fuel spills, wait until it dries before you start the engine.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

Fuel Filter, if equipped

1. Before you clean or replace the fuel filter (A, Figure 17), drain the fuel tank or close

the fuel shut-off valve. If the fuel tank is not drained, fuel leakage could occur and

cause a fire or explosion.

2. Use pliers to squeeze tabs (B, Figure 17) on the clamps (C), then move the clamps

away from the fuel filter (A). Twist and pull the fuel lines (D) off of the fuel filter.

3. Check the fuel lines (D, Figure 17) for cracks or leaks. Replace if necessary.

4. Replace the fuel filter (A, Figure 17) with an original equipment replacement filter.

5. Attach the fuel lines (D, Figure 17) with clamps (C).

Storage

Fuel System

Refer to Figure: 18.

Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 18) with

fuel. For fuel expansion, do not fill above the fuel tank neck (B).

Fuel can become stale when kept in a storage container for more than 30 days. Each

time you fill the container with fuel, addSTA-BIL 360°

PROTECTION™to the fuel as

specified by the manufacturer’s instructions. This keeps fuel fresh and decreases fuel-

related problems or contamination in the fuel system.

It is not necessary to drain fuel from the engine whenSTA-BIL

360°

PROTECTION™is added as instructed. Before storage, turn the engine ON for 2

minutes to move the fuel and stabilizer through the fuel system.

If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained

into an approved container. Operate the engine until it stops from lack of fuel. The use of

a fuel stabilizer in the storage container is recommended to keep fuel fresh.

Engine Oil

While the engine is still warm, change the engine oil. Refer to Change the Engine Oil

section.

Troubleshooting

Assistance

For assistance, contact your local dealer or go to vanguardpower.com or call

1-800-999-9333 (in USA).

Specifications

Specifications and Service Parts

Models: 540000 , 54E000

Displacement 54.68 ci (896 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.071 in (78,0 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Not for

Reproduction

Models: 610000, 61E000, 61G200, 61G300

Displacement 60.60 ci (993 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.406 in (86,5 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap .030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Armature Air Gap .005 - .008 in (,13 - ,20 mm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Service Parts - Models: 540000, 54E000,

610000, 61E000, 61G200, 61G300

Service Part Part Number

Cyclonic Air Filter (Figure 13) 841497

Cyclonic Safety Filter (Figure 13) 821136

Air Filter, Low Profile (Figure 14) 692519

Pre-cleaner, Low Profile (Figure 14) 692520

Oil - SAE 30 100028

Oil Filter 842921

Fuel Filter 691035

Resistor Spark Plug 491055

Long Life Platinum Spark Plug 5066

Spark Plug Wrench 19374

Spark Tester 19368

Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily

at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted

operating limits on slopes.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance

with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque

Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM

for all others; horsepower values are derived at 3600 RPM. The gross power curves

can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with

exhaust and air cleaner installed whereas gross power values are collected without

these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine-to-engine

variability. Given the wide array of products on which engines are placed, the gasoline

engine may not develop the rated gross power when used in a given piece of power

equipment. This difference is due to a variety of factors including, but not limited to, the

variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,

Briggs & Stratton may substitute an engine of higher rated power for this engine.

Warranty

Briggs & Stratton Engine Warranty

Effective January 2019

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair

or replace, free of charge, any part that is defective in material or workmanship or

both. Transportation charges on product submitted for repair or replacement under this

warranty must be borne by purchaser. This warranty is effective for and is subject to

the time periods and conditions stated below. For warranty service, find the nearest

Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.

The purchaser must contact the Authorized Service Dealer, and then make the product

available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of

merchantability and fitness for a particular purpose, are limited to the warranty

period listed below, or to the extent permitted by law. Liability for incidental or

consequential damages are excluded to the extent exclusion is permitted by law. Some

states or countries do not allow limitations on how long an implied warranty lasts,

and some states or countries do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation and exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state and country to country

Standard Warranty Terms

1, 2, 3

Vanguard®; Commercial Series

Consumer Use - 36 months

Commercial Use - 36 months

XR Series

Consumer Use - 24 months

Commercial Use - 24 months

All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve

Consumer Use - 24 months

Commercial Use - 12 months

All Other Engines

Consumer Use - 24 months

Commercial Use - 3 months

These are our standard warranty terms, but occasionally there may be additional

warranty coverage that was not determined at time of publication. For a listing

of current warranty terms for your engine, go to BRIGGSandSTRATTON.com or

contact your Briggs & Stratton Authorized Service Dealer.

There is no warranty for engines on equipment used for prime power in place

of a utility; standby generators used for commercial purposes, utility vehicles

exceeding 25 MPH, or engines used in competitive racing or on commercial or

rental tracks.

Vanguard installed on standby generators: 24 months consumer use, no

warranty commercial use. Commercial Series with manufacturing date before July

2017: 24 months consumer use, 24 months commercial use.

In Australia - Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure.

For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by

emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.

The warranty period begins on the original date of purchase by the first retail or

commercial consumer. "Consumer use" means personal residential household use by a

retail consumer. "Commercial use" means all other uses, including use for commercial,

income producing or rental purposes. Once an engine has experienced commercial

use, it shall thereafter be considered as a commercial use engine for purposes of this

warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial

purchase date at the time warranty service is requested, the manufacturing date

of the product will be used to determine the warranty period. Product registration

is not required to obtain warranty service on Briggs & Stratton products.

About Your Warranty

This limited warranty covers engine-related material and/or workmanship issues only,

and not replacement or refund of the equipment to which the engine may be mounted.

Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered

under this warranty. Similarly, warranty is not applicable if the engine has been altered

or modified or if the engine serial number has been defaced or removed. This warranty

does not cover engine damage or performance problems caused by:

1. The use of parts that are not original Briggs & Stratton parts;

2. Operating the engine with insufficient, contaminated, or an incorrect grade of

lubricating oil;

3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater than

10%, or the use of alternative fuels such as liquefied petroleum or natural gas on

engines not originally designed/manufactured by Briggs & Stratton to operate on

such fuels;

4. Dirt which entered the engine because of improper air cleaner maintenance or re-

assembly;

5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly

installed blade adapters, impellers, or other crankshaft coupled devices, or

excessive v-belt tightness;

6. Associated parts or assemblies such as clutches, transmissions, equipment

controls, etc., which are not supplied by Briggs & Stratton;

7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or

clog the cooling fins or flywheel area, or by operating the engine without sufficient

ventilation;

8. Excessive vibration due to over-speeding, loose engine mounting, loose or

unbalanced cutter blades or impellers, or improper coupling of equipment

components to the crankshaft;

10 vanguardpower.com

Not for

Reproduction

9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of

equipment, or improper engine installation.

Warranty service is available only through Briggs & Stratton Authorized Service

Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map

at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).

80004537 (Rev. F)

Briggs & Stratton Emissions Warranty

California, U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty -

Your Warranty Rights and Obligations

For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-

Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)

The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are

pleased to explain the exhaust emissions (“emissions”) control system warranty on

your 2020-2022 engine. In California, new small off-road engines and large spark

ignited engines less than or equal to 1.0 liter must be designed, built, and equipped

to meet the State’s stringent anti-smog standards. B&S must warrant the emissions

control system on your engine for the periods of time listed below provided there has

been no abuse, neglect or improper maintenance of your small off-road engine or

equipment leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your engine is warranted for two years.

If any emissions-related part on your engine is defective, the part will be repaired or

replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your owner’s manual. B&S recommends that you retain

all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or for your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect, or

improper maintenance or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center

or service center as soon as the problem exists. The warranty repairs shall

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of two years from the date of delivery to an ultimate

purchaser, or for the time period listed in the respective engine or product warranty

statement, whichever is greater. B&S warrants to the original purchaser and each

subsequent purchaser that the engine is designed, built, and equipped so as to

conform with all applicable regulations adopted by the Air Resources Board; that

it is free from defects in material and workmanship that could cause the failure

of a warranted part; and that it is identical in allmaterial respects to the engine

described in the manufacturer’s application for certification. The warranty period

begins on the date the engine or equipment is delivered to an ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operators’s Manual supplied, is warranted for the period

of time prior to the first scheduled replacement point for that part. If the

part fails prior to the first scheduled replacement, the part will be repaired

or replaced by B&S at no charge to the owner. Any such part repaired or

replaced under warranty will be warranted for the remainder of the period

prior to the first scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the Air Resources Board

may not be used. The use of any non-exempted add-on or modified parts by

the owner will be grounds for disallowing a warranty claim. The manufacturer

will not be liable to warrant failures of warranted parts caused by the use of a

non-exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Small Off-Road Engine Emissions Label

Engines that are certified to meet the California Air Resources Board (CARB) small off-

road Emissions Standard must display information regarding the Emissions Durability

Period and the Air Index. Briggs & Stratton makes this information available to the

consumer on our emissions labels. The engine emissions label will indicate certification

information.

The Emissions Durability Period describes the number of hours of actual running

time for which the engine is certified to be emissions compliant, assuming proper

maintenance in accordance with the Operator’s Manual. The following categories are

used:

Moderate:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

50 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 125 hours of actual engine running time.

Intermediate:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

125 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 250 hours of actual engine running time.

Extended:

Engines at or less than 80 cc displacement are certified to be emissions compliant for

300 hours of actual engine running time. Engines greater than 80 cc displacement are

certified to be emissions compliant for 500 hours of actual engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.

Therefore, the Emissions Durability Period of an engine with an intermediate rating

would equate to 10 to 12 years.

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions

Compliance Period referred to on the Emissions Compliance label indicates the

Not for

Reproduction

number of operating hours for which the engine has been shown to meet Federal

emissions requirements.

For engines at or less than 80 cc displacement:

Category C = 50 hours, Category B = 125 hours, Category A = 300 hours

For engines greater than 80 cc displacement and less than 225 cc displacement:

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement:

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

80099153(Revision A)

Briggs & Stratton Emissions Warranty

U.S. EPA, and Briggs & Stratton, LLC Emissions Control Warranty Statement -

Your Warranty Rights and Obligations

For Briggs & Stratton Engine Models with "J" Trim Designation (Model-Type-

Trim Representation xxxxxx xxxx Jx)

The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust

emissions control system warranty on your Model Year 2020-2022 engine. In the U.S,

new small off-road engines and large spark ignited engines less than or equal to 1.0

liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S

must warrant the emissions control system on your engine for the periods of time listed

below provided there has been no abuse, neglect, or improper maintenance of your

engine leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your engine is warranted for two years. If

any emissions-related parts on your engine is defective, the part will be repaired of

replaced by B&S.

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your Operator’s Manual. B&S recommends that you

retain all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect,

improper maintenance, or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center,

or service center, as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of two years from the date of delivery to an ultimate

purchaser, or for the period listed in the respective engine or product warranty

statement, whichever is greater. B&S warrants to the original purchaser and each

subsequent purchaser that the engine is designed, built, and equipped so as to

conform with all applicable regulations under Section 213 of the Clean Air Act that

is free from defects in material and workmanshipthat could cause the failure of a

warranted part; and that is identical in all material respects to the engine described

in the manufacturer’s application for certification. The warranty period begins on

the date the engine or equipment is delivered to an ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operator's Manual supplied, is warranted for the period of

time prior to the first scheduled replacement point for that part. If the part fails

prior to the first scheduled replacement, the part will be repaired or replaced

by B&S at no charge to the owner. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first

scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the U.S. EPA may not be

used. The use of any non-exempted add-on or modified parts by the owner

will be grounds for disallowing a warranty claim. The manufacturer will not

be liable to warrant failures of warranted parts caused by the use of a non-

exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

Look For Relevant Emissions Durability Period and Air Index Information On

Your Small Off-Road Engine Emissions Label

Briggs & Stratton engines are certified to meet the United States Environmental

Protection Agency (USEPA) Phase 3 emissions standards. The Emissions Compliance

Period referred to on the Emissions Compliance label indicates the number of

operating hours for which the engine has been shown to meet Federal emissions

requirements.

For engines at or less than 80 cc displacement:

Category C = 50 hours, Category B = 125 hours, Category A = 300 hours

For engines greater than 80 cc displacement and less than 225 cc displacement:

Category C = 125 hours, Category B = 250 hours, Category A = 500 hours

For engines of 225 cc or more displacement:

Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours

80099149 (Revision A)

12 vanguardpower.com

Not for

Reproduction

Información general

Este manual contiene información de seguridad para que conozca los peligros y riesgos

relacionados con este motor y la forma de prevenirlos. También contiene instrucciones

para el uso y cuidado correctos del motor. Ya que Briggs & Stratton no conoce el equipo

donde se usará este motor, es importante que usted lea, entienda y obedezca estas

instrucciones. Guarde estas instrucciones originales para referencia futura.

NOTA:Las figuras e ilustraciones de este manual son solo como referencia y pueden

ser diferentes de las de su modelo. Si necesita ayuda, póngase en contacto con un

distribuidor de servicio autorizado.

Para obtener información de piezas de repuesto o asistencia técnica, registre la fecha

de compra, el modelo de motor, el tipo, características específicas y el número de

serie del motor. Estos números están ubicados en su motor. Consulte la sección

Características y controles.

Fecha de compra

Modelo del motor - Tipo - Reglaje

Número de Serie del motor

Información de contacto de la oficina en

Europa

Si tiene preguntas relacionadas con las emisiones europeas, póngase en contacto con

nuestra oficina en Europa en:

Max-Born-Straße2, 68519 Viernheim, Alemania.

EtapaV (5) de la Unión Europea (UE):

Valores del dióxido de carbono (CO2)

Ingrese CO2 en la ventana de búsqueda en BriggsandStratton.com. para encontrar los

valores de dióxido de carbono de los motores de Briggs & Stratton con certificado de

aprobación tipo UE.

Información de reciclaje

Recicle todos los cartones, cajas, aceite usado y baterías

según lo especifiquen las regulaciones gubernamentales.

Seguridad del operador

Símbolo de alerta de seguridad y palabras de

señalización

El símbolo de alerta de seguridad identifica información de seguridad

sobre peligros que podrían provocar lesiones personales. Se usa una palabra

de señalización (PELIGRO, ADVERTENCIA, o PRECAUCIÓN) para indicar la

probabilidad y la gravedad potencial de las lesiones. Además, se usa un símbolo de

peligro para representar el tipo de riesgo.

PELIGRO indica un riesgo que, si no se evita, ocasionará la muerte o lesiones

graves.

ADVERTENCIA indica un riesgo que, si no se evita, podría ocasionar la muerte o

lesiones graves.

PRECAUCIÓN indica un riesgo que, si no se evita, podría ocasionar lesiones

menores o moderadas.

AVISO indica información que se considera importante pero que no está relacionada

con un peligro.

Símbolos de peligro y significados

Información de seguridad

sobre peligros que pueden

conllevar a lesiones

personales.

Lea y entienda el Manual

del operador antes

de operar y realizar

mantenimientos a la

unidad.

Peligro de incendio Peligro de explosión

Peligro de descarga

eléctrica

Peligro de vapores tóxicos

Peligro de superficie

caliente

Peligro de ruido:

Protección auditiva

recomendada para uso

extendido.

Peligro de elemento

lanzado: utilizar protección

para los ojos.

Peligro de explosión

Peligro de congelación Peligro de retroceso

violento

Peligro de amputación:

piezas móviles

Peligro químico

Peligro de calor térmico Peligro de líquidos

corrosivos

Mensajes de seguridad

ADVERTENCIA

Este producto puede exponerlo a sustancias químicas, entre las que se incluyen

emisiones de escape de motor de gasolina, reconocidas por el estado de California

como causantes de cáncer, y monóxido de carbono, reconocido por el estado de

California como causante de defectos de nacimiento u otros problemas reproductivos.

Para obtener más información, visite www.P65Warnings.ca.gov.

ADVERTENCIA

Los motores Briggs & Stratton® no están diseñados, y no deben utilizarse, para

potenciar carritos motorizados, go karts; vehículos para niños; vehículos recreativos;

vehículos deportivos todo terreno (ATV); motocicletas; aerodeslizadores; equipo

aeronáutico; o vehículos utilizados en eventos de competencia que no estén avalados

por Briggs & Stratton. Para obtener información acerca de productos de carrera

profesionales, consulte www.briggsracing.com. Para usar el motor en ATV utilitarios

y sidebyside, comuníquese con el Centro de aplicacione de potencia de Briggs &

Stratton llamando al 1-866-927-3349. El uso incorrecto del motor podría provocar

lesiones graves o la muerte.

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Cuando agregue combustible

• Detenga el motor. Antes de quitar la tapa del combustible, espere un mínimo de

dos (2) minutos para asegurarse de que el motor esté frío.

• Llene el tanque de combustible al aire libre o en un área con buena circulación

de aire.

• No ponga demasiado combustible en el tanque. Para permitir la expansión del

combustible, no llene el tanque de combustible arriba de la parte inferior del

cuello.

• Mantenga el combustible alejado de chispas, llamas abiertas, llamas piloto,

calor y otras fuentes de ignición.

• Examine frecuentemente las líneas de combustible, el tanque de combustible, la

tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace

las piezas dañadas.

• Si el combustible se derrama, espere a que se seque antes de arrancar el

motor.

Cuando arranque el motor

• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el limpiador

de aire (si tiene) estén correctamente instalados.

• No arranque el motor si retiró la bujía.

• Si el motor está inundado, lleve el estrangulador (si tiene) a la posición

ABIERTO o MARCHA. Mueva el acelerador (si tiene) a la posición RÁPIDO y de

arranque hasta que el motor se encienda.

Not for

Reproduction

• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.

• Puesto que los vapores son inflamables, no utilice fluidos de encendido

presurizados.

Cuando opere el equipo

• No incline el motor o el equipo en un ángulo que cause derramamiento del

combustible.

• No cebe el carburador (si tiene) para detener el motor.

• Nunca arranque u opere el motor sin el limpiador de aire (si tiene) o el filtro de

aire (si tiene).

Cuando lleve a cabo mantenimiento

• Si drena el aceite desde el tubo de llenado de aceite superior, el tanque de

combustible debe estar vacío. Si no está vacío, puede producirse un derrame de

combustible y podría ocasionarse un incendio o una explosión.

• Durante el mantenimiento, si es necesario inclinar la unidad, asegúrese de

que el tanque de combustible, si está montado en el motor, esté vacío y

que el extremo del motor donde está la bujía esté elevado. Si el tanque de

combustible no está vacío, puede producirse un derrame de combustible y

podría ocasionarse un incendio o una explosión.

• Examine frecuentemente las líneas de combustible, el tanque de combustible, la

tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace

las piezas dañadas.

• No cambie el resorte del regulador, las conexiones u otras piezas para

aumentar la velocidad del motor.

• No golpee el volante con un martillo o un objeto duro. Esto podría provocar una

falla en el volante durante la operación.

• Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas

en la misma posición que las piezas originales. Otras piezas podrían provocar

daños o lesiones.

Cuando traslada la ubicación del equipo

• Asegúrese de que el tanque de combustible esté VACÍO o que la válvula de

cierre de combustible esté en la posición CERRADA.

Cuando el combustible o el equipo está almacenado con combustible en el

tanque de combustible

• Puesto que las luces piloto u otras fuentes de ignición pueden causar

explosiones, mantenga el combustible o el equipo lejos de hornos, estufas,

calentadores de agua u otros aparatos que tengan luces piloto.

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

El arranque del motor causa una chispa que podría provocar un incendio o una

explosión.

• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.

• Puesto que los vapores son inflamables, no utilice fluidos de encendido

presurizados.

ADVERTENCIA

PELIGRO DE GAS NOCIVO. Las emisiones del motor contienen monóxido de

carbono, un gas nocivo que podría causar la muerte en minutos. Aunque no huela

los gases del escape, puede estar expuesto al peligroso gas de monóxido de

carbono. Si usted se siente enfermo, adormecido, o débil al utilizar este producto,

diríjase hacia un lugar con aire fresco DE INMEDIATO. Consulte a un médico. Es

probable que se haya intoxicado con monóxido de carbono.

• El gas de monóxido de carbono puede acumularse en los espacios habitados.

Para reducir el riesgo del gas de monóxido de carbono, SOLAMENTE opere

este producto al aire libre, lejos de ventanas, puertas y ventilaciones,.

• Instale alarmas de monóxido de carbono operadas por baterías o alarmas

de monóxido de carbono para enchufar con batería de respaldo según lo

que especifiquen las instrucciones del fabricante. Los detectores de humo no

detectan el gas de monóxido de carbono.

• NO opere este producto en viviendas, garajes, sótanos, espacios reducidos,

cobertizos u otros espacios cerrados, incluso si usa ventiladores o deja las

puertas y ventanas abiertas a manera de ventilación. Después de la operación

de este producto, el monóxido de carbono puede acumularse rápidamente en

estos espacios y permanecer durante horas.

• SIEMPRE ubique este producto a favor del viento y mantenga el escape del

motor alejado de los espacios confinados.

ADVERTENCIA

La retracción rápida del cordón del arrancador (retroceso) tirará de su mano y

brazo hacia el motor más rápido de lo que puede sostenerlo. Podrían presentarse

roturas en los huesos, fracturas, contusiones, o torceduras.

• Para evitar el retroceso al arrancar el motor, hale del cordón del arrancador

lentamente hasta sentir resistencia y luego suéltelo rápidamente.

• Antes de arrancar el motor, desconecte o retire cualquier carga externa del

motor/equipo.

• Asegúrese de que los componentes del equipo acoplados directamente, entre

otros, cuchillas, propulsores, poleas y ruedas dentadas estén firmemente

acoplados.

ADVERTENCIA

Las partes giratorias pueden atrapar las manos, los pies, el cabello, la ropa o los

accesorios y provocar una amputación o laceración traumática.

• Opere el equipo con protectores correctamente instalados.

• Mantenga sus manos y pies alejados de las piezas giratorias.

• Quítese las joyas y asegúrese de que el pelo largo esté apartado de todas las

piezas giratorias.

• No use ropa suelta o artículos que puedan quedar atrapados.

ADVERTENCIA

Durante la operación, el motor y el silenciador se calientan. Si toca un motor

caliente, pueden producirse quemaduras térmicas.

Los materiales combustibles, como hojas, césped y hierbas se pueden inflamar.

• Antes de tocar el motor o el silenciador, detenga el motor y espere dos (2)

minutos. Asegúrese de que el motor y el silenciador se puedan tocar con

seguridad.

• Quite los residuos del silenciador y del motor.

Es una infracción del Código de Recursos Públicos de California (California Public

Resource Code), Sección4442, utilizar u operar el motor en cualquier terreno forestal o

cubierto por árboles o césped, a menos que el sistema de escape esté equipado con un

supresor de chispas, en virtud de la Sección4442, el cual se debe mantener en buenas

condiciones de operación. Es posible que otros estados o jurisdicciones federales

cuenten con leyes similares; consulte la Regulación Federal 36CFR Sección 261.52.

Póngase en contacto con el vendedor, el distribuidor o el fabricante del equipo original

para obtener un extintor de chispas diseñado para el sistema de escape instalado en

este motor.

ADVERTENCIA

La chispa accidental del motor puede ocasionar una descarga eléctrica o un

incendio y podría provocar enredos, amputaciones traumáticas o laceraciones.

Antes de que realice ajustes o reparaciones:

• Desconecte el cable de la bujía y manténgalo lejos de la bujía.

• Desconecte el cable de la batería del terminal negativo de la batería (solo

motores con arranque eléctrico)

• Use solamente las herramientas correctas.

Cuando verifique si hay chispa:

• Use un probador de bujías aprobado.

• No revise si hay chispa con la bujía extraída.

ADVERTENCIA

Los vapores del combustible son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Si siente olor a gas

• No arranque el motor.

• No encienda interruptores eléctricos.

• No use un teléfono en las cercanías.

• Desaloje el área.

• Comuníquese con el proveedor de gas o con los bomberos.

Características y controles

Controles del motor

Compare las letras de las leyendas en las Figuras 1, 2, 3, y 4 con los controles del

motor en la lista a continuación:

A. Números de identificación del motorModelo - Tipo - Código

B. Bujía

C. Filtro de aire ciclónico

14 vanguardpower.com

Not for

Reproduction

D. Limpiador de aire, bajo perfil

E. Tapones de la varilla

F. Llenado de aceite

G. Filtro de aceite

H. Tapón de drenaje de aceite

I. Sensor de presión de aceite

J. Protector para los dedos

K. Arrancador eléctrico

L. Solenoide del arrancador

M. Regulador/Rectificador

N. Carburador - Modelos con carburador

O. Enfriador de aceite (si está equipado)

P. Silenciador (de estar equipado)

Q. Bomba de combustible

Interruptor de arranque

Control del acelerador

Control del estrangulador(Modelos con carburador

)

U. Filtro de combustible

V. Tacómetro (si está equipado)

Algunos motores y equipos cuentan con controles remotos. Consulte el manual del

equipo para conocer la ubicación y la operación de los controles remotos.

Símbolos de control del motor y significados

Velocidad del motor -

RÁPIDA

Velocidad del motor -

LENTA

Velocidad del motor -

DETENER

ENCENDIDO/APAGADO

Arranque del motor

Estrangulador CERRADO

Arranque del motor

Estrangulador ABIERTO

Tapa del combustible

Válvula de cierre de

combustible - ABIERTO

Válvula de cierre de

combustible - CERRADO

Nivel de combustible -

Máximo

No lo llene en exceso

Operación

Recomendaciones sobre el aceite

Capacidad de aceite: Consulte la secciónEspecificaciones.

AVISO

Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o

distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el

motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue

el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor

sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la

garantía.

Recomendamos el uso de aceites Briggs&Stratton

con garantía certificada para

un mejor rendimiento. Se permiten otros aceites detergentes de alta calidad, si están

clasificados para servicio SF, SG, SH, SJ o superior. No use aditivos especiales.

Use el cuadro para seleccionar la mejor viscosidad para el margen de temperatura

exterior que se espera. Los motores en la mayoría de equipo motorizado para

exteriores operan bien con aceite sintético 5W-30. Para equipos que operan a altas

temperaturas, el aceite sintético Vanguard

15W-50 brinda la mejor protección.

A SAE30 - El uso de SAE30 a temperaturas inferiores a 40°F (4°C) provocará

dificultades de arranque.

B 10W-30 - El uso de 10W-30 a temperaturas mayores a 80°F (27°C) puede

provocar un aumento en el consumo de aceite. Verifique el nivel de aceite con

frecuencia.

C 5W-30

D 5W-30 sintético

Vanguard

Sintético 15W-50

Revisión y adición de aceite

Antes de verificar o agregar aceite

• Asegúrese de que el motor esté nivelado.

• Limpie todos los desechos del área de llenado de aceite.

• Consulte la sección Especificacionespara obtener la capacidad de aceite.

AVISO

Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o

distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el

motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue

el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor

sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la

garantía.

1. Retire la varilla indicadora de nivel (A, Figura 5) y séquela con un paño limpio.

2. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 5).

3. Retire la varilla y revise el nivel de aceite. Asegúrese de que el nivel de aceite

esté en la parte superior del indicador de lleno (B, Figura 5) de la varilla indicadora

de nivel de aceite.

4. Si el nivel de aceite es bajo, agregue aceite lentamente en el llenado de aceite

del motor (C, Figura 5). No agregue demasiado aceite. Después de que agregue

aceite, espere un minuto y vuelva a verificar el nivel de aceite. Asegúrese de que

el nivel de aceite sea el correcto.

5. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 5).

Sistema de protección de bajo nivel de aceite (si

tiene)

En algunos motores se ha instalado un sensor de bajo nivel de aceite. Si el nivel

de aceite está bajo, el sensor mostrará una luz de advertencia o detendrá el motor.

Detenga el motor y siga estos pasos antes de arrancar el motor.

• Asegúrese de que el motor esté nivelado.

• Haga una comprobación del nivel de aceite. Consulte la secciónVerificación

del nivel de aceite.

• Si el nivel de aceite es bajo, agregue la cantidad correcta de aceite. Arranque el

motor y asegúrese de que la luz de advertencia (si tiene) no se encienda.

• Si el nivel de aceite es bajo, no arranque el motor. Comuníquese con un

distribuidor de servicio autorizado de Briggs & Stratton para que le corrijan el

problema del aceite.

Recomendaciones acerca del combustible

El combustible debe cumplir con estos requisitos:

• Gasolina limpia, fresca y sin plomo.

• Un mínimo de 87octanos/87AKI (91RON). Para uso en grandes alturas,

consulte a continuación.

• Se permite gasolina con hasta un 10% de etanol (gasohol).

AVISO

No utilice gasolina no aprobada, como la E15 y la E85. No mezcle la gasolina con

aceite ni cambie el motor para usarlo con combustibles alternativos. El uso de

combustibles no aprobados podría provocar daños a los componentes del motor, lo que

no será reparado bajo la garantía.

Not for

Reproduction

Para proteger el sistema de combustible de la formación de goma, mezcle el

combustible con un estabilizador. Consulte la sección Almacenamiento. No todos los

combustibles son iguales. Si ocurren problemas de arranque o de rendimiento, cambie

el proveedor o la marca del combustible. Este motor está certificado para funcionar

con gasolina. El sistema de control de emisiones para motores carburados es EM

(modificaciones del motor). Los sistemas de control de emisiones para motores con

inyección de combustible electrónica son ECM (módulo de control del motor), MPI

(inyección multipuerto) y, si lo tiene, un O2S (sensor de oxígeno).

Gran altura

En alturas de más de 5000pies (1524metros), se permite una gasolina con un mínimo

de 85octanos/85AKI (89 RON).

Para motores carburados, se requiere realizar el ajuste de gran altura para mantener

el rendimiento. El funcionamiento sin este ajuste provocará una disminución en

el rendimiento y un aumento en el consumo de combustible y en las emisiones.

Comuníquese con un Distribuidor de Servicio Autorizado por Briggs & Stratton para

obtener información sobre el ajuste de gran altura. No se recomienda operar la

máquina a alturas menores de 2500pies (762metros) con el ajuste de gran altura.

En el caso de motores con inyección de combustible electrónica (EFI), no se requiere

un ajuste de gran altura.

Agregar combustible

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Cuando agregue combustible

• Detenga el motor. Antes de quitar la tapa del combustible, espere un mínimo de

dos (2) minutos para asegurarse de que el motor esté frío.

• Llene el tanque de combustible al aire libre o en un área con buena circulación

de aire.

• No ponga demasiado combustible en el tanque. Para permitir la expansión del

combustible, no llene el tanque de combustible arriba de la parte inferior del

cuello.

• Mantenga el combustible alejado de chispas, llamas abiertas, llamas piloto,

calor y otras fuentes de ignición.

• Examine frecuentemente las líneas de combustible, el tanque de combustible, la

tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace

las piezas dañadas.

• Si el combustible se derrama, espere a que se seque antes de arrancar el

motor.

1. Limpie la suciedad y los desechos en el área de la tapa de llenado de combustible.

Retire la tapa de llenado de combustible.

2. Llene el tanque de combustible (A, Figura 6) con combustible. Puesto que el

combustible se expandirá, no llene más arriba de la parte inferior del cuello del

tanque de combustible (B).

3. Instale la tapa de llenado de combustible.

Arrancar y detener motor

Arranque del motor

ADVERTENCIA

La retracción rápida del cordón del arrancador (retroceso) tirará de su mano

y brazo hacia el motor más rápido de lo que puede sostenerlo. Podrían

presentarse roturas en los huesos, fracturas, contusiones, o torceduras.

• Para evitar el retroceso al arrancar el motor, hale del cordón del arrancador

lentamente hasta sentir resistencia y luego suéltelo rápidamente.

• Antes de arrancar el motor, desconecte o retire cualquier carga externa del

motor/equipo.

• Asegúrese de que los componentes del equipo acoplados directamente, entre

otros, cuchillas, propulsores, poleas y ruedas dentadas estén firmemente

acoplados.

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Cuando arranque el motor

• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el limpiador

de aire (si tiene) estén correctamente instalados.

• No arranque el motor si retiró la bujía.

• Si el motor está inundado, lleve el estrangulador (si tiene) a la posición

ABIERTO o MARCHA. Mueva el acelerador (si tiene) a la posición RÁPIDO y

de arranque hasta que el motor se encienda.

• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el

motor.

• Puesto que los vapores son inflamables, no utilice fluidos de encendido

presurizados.

ADVERTENCIA

PELIGRO DE GAS NOCIVO. Las emisiones del motor contienen monóxido de

carbono, un gas nocivo que podría causar la muerte en minutos. Aunque no

huela los gases del escape, puede estar expuesto al peligroso gas de monóxido

de carbono. Si usted se siente enfermo, adormecido, o débil al utilizar este

producto, diríjase hacia un lugar con aire fresco DE INMEDIATO. Consulte a un

médico. Es probable que se haya intoxicado con monóxido de carbono.

• El gas de monóxido de carbono puede acumularse en los espacios habitados.

Para reducir el riesgo del gas de monóxido de carbono, SOLAMENTE opere

este producto al aire libre, lejos de ventanas, puertas y ventilaciones,.

• Instale alarmas de monóxido de carbono operadas por baterías o alarmas

de monóxido de carbono para enchufar con batería de respaldo según lo

que especifiquen las instrucciones del fabricante. Los detectores de humo no

detectan el gas de monóxido de carbono.

• NO opere este producto en viviendas, garajes, sótanos, espacios reducidos,

cobertizos u otros espacios cerrados, incluso si usa ventiladores o deja las

puertas y ventanas abiertas a manera de ventilación. Después de la operación

de este producto, el monóxido de carbono puede acumularse rápidamente en

estos espacios y permanecer durante horas.

• SIEMPRE ubique este producto a favor del viento y mantenga el escape del

motor alejado de los espacios confinados.

AVISO

Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o

distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el

motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue

el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor

sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la

garantía.

Tipos de sistemas de encendido

Antes de arrancar el motor, debe conocer el tipo de sistema de encendido de su

motor. Su motor tendrá uno de estos tipos.

• Sistema de inyección de combustible electrónica (EFI): Un sistema EFI no

tiene un estrangulador ni un cebador.

• Sistema del estrangulador: Este tipo de sistema tiene un estrangulador que

se debe utilizar en temperaturas frías. Algunos modelos tendrán un control de

estrangulamiento separado mientras que otros tendrán una combinación de

control de estrangulador y acelerador. No tiene cebador.

NOTA:Su equipo podría tener controles remotos. Consulte el manual del equipo para

conocer la ubicación y el funcionamiento de los controles remotos.

Sistema de inyección de combustible electrónica (EFI)

1. Revise el aceite del motor. Consulte la secciónVerificación del nivel de aceite.

2. Asegúrese de que los controles de transmisión del equipo, de estar equipados,

estén desactivados.

3. Mueva la válvula de cierre de combustible (A, Figura 7), si tiene, a la posición

ABIERTO.

4. Mueva el control del acelerador (B, Figura 7), si está equipado, a la posición

RÁPIDO. Opere el motor en la posición RÁPIDO.

5. Gire el interruptor de arranque eléctrico (D, Figura7) a la posición ENCENDIDO o a

la posición ARRANQUE.

AVISOPara prolongar la vida útil del arrancador, haga ciclos cortos de arranque (cinco

segundos como máximo). Espere un minuto entre los ciclos de arranque.

Si el motor no arranca después de 3 o 4 intentos, póngase en contacto con su

distribuidor local o vaya a vanguardpower.com o llame 1-800-999-9333.

Sistema del estrangulador

1. Revise el aceite del motor. Consulte la secciónVerificación del nivel de aceite.

16 vanguardpower.com

Not for

Reproduction

2. Asegúrese de que los controles de transmisión del equipo, de estar equipados,

estén desactivados.

3. Mueva la válvula de cierre de combustible (A, Figura 7), si tiene, a la posición

ABIERTO.

4. Mueva el control del acelerador (B, Figura 7), si está equipado, a la posición

RÁPIDO. Opere el motor en la posición RÁPIDO.

5. Mueva el control del estrangulador (C, Figura 7), o la combinación de control de

estrangulador y acelerador (B, C) a la posición CERRADO.

NOTA:Para arrancar el motor con un sistema de combustible seco, será necesario un

tiempo adicional de arranque en la posición estrangulador. Esto dará tiempo a la bomba

de combustible para cebar el sistema de combustible.

6. Gire el interruptor de llave (D, Figura7) a la posición ENCENDIDO o a la posición

ARRANQUE.

7. Si el motor arranca pero no sigue operando, mueva el control del estrangulador (C,

Figura 7) a la posición ABIERTO para arrancar el motor.

AVISOPara prolongar la vida útil del arrancador, haga ciclos cortos de arranque (cinco

segundos como máximo). Espere un minuto entre los ciclos de arranque.

8. Cuando se caliente el motor, mueva el control del estrangulador (C, Figura 7) a la

posición ABIERTO.

Si el motor no arranca después de 3 o 4 intentos, póngase en contacto con su

distribuidor local o vaya a vanguardpower.com o llame 1-800-999-9333.

Detención del motor

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

• No cebe el carburador (si tiene) para detener el motor.

1. Con el control del acelerador en la posición LENTO, coloque el interruptor de

arranque eléctrico (D, Figura 7) en la posición APAGADO. Retire la llave y

manténgala en un lugar seguro fuera del alcance de los niños.

2. Después de que se haya detenido el motor, mueva la válvula de cierre de

combustible (A, Figura 7), si tiene, a la posición CERRADO.

Mantenimiento

Información de mantenimiento

ADVERTENCIA

Durante el mantenimiento, si es necesario inclinar la unidad, asegúrese de que el

tanque de combustible, si está montado en el motor, esté vacío y que el extremo del

motor donde está la bujía esté elevado. Si el tanque de combustible no está vacío,

puede producirse un derrame de combustible y podría ocasionarse un incendio o una

explosión. Si el motor está inclinado en una dirección diferente, no arrancará fácilmente

debido a la contaminación del filtro de aire o de la bujía por aceite o combustible.

Le recomendamos que consulte a un distribuidor de servicio autorizado de Briggs &

Stratton para cualquier mantenimiento y servicio del motor y de las piezas del motor.

AVISO

Todos los componentes usados para armar este motor deben permanecer en su lugar

para un funcionamiento apropiado.

ADVERTENCIA

La chispa accidental del motor puede ocasionar una descarga eléctrica o un

incendio y podría provocar enredos, amputaciones traumáticas o laceraciones.

Antes de que realice ajustes o reparaciones:

• Desconecte el cable de la bujía y manténgalo lejos de la bujía.

• Desconecte el cable de la batería del terminal negativo de la batería (solo

motores con arranque eléctrico)

• Use solamente las herramientas correctas.

Cuando verifique si hay chispa:

• Use un probador de bujías aprobado.

• No revise si hay chispa con la bujía extraída.

Mantenimiento del control de emisiones

Para el mantenimiento, la sustitución o la reparación de los dispositivos y

sistemas de control de emisiones, póngase en contacto con un establecimiento

de reparación de motores todo terreno calificado o con un técnico de servicio. Sin

embargo, para obtener un servicio de control de emisiones “sin costo”, el trabajo debe

ser realizado por un distribuidor autorizado de la fábrica. Consulte las Declaraciones de

Control de Emisiones.

Programa de mantenimiento

Intervalos de 8 horas o diariamente

• Revise el nivel de aceite del motor.

• Limpie el área alrededor del silenciador y los controles.

Intervalos de 100 horas o anualmente

•

Limpie o cambie el filtro de aire

1 2

• Cambie el aceite del motor y el filtro.

• Cambie el filtro de aceite (si está equipado).

• Reemplace las bujías.

• Verifique el silenciador y el supresor de chispas.

• Realice el mantenimiento del sistema de escape.

Intervalos de 250 horas o anualmente

• Verifique el espacio libre de la válvula. Ajústelo si es necesario.

Intervalos de 400 horas o anualmente

•

Cambie el filtro de aire

• Reemplace el filtro de combustible.

•

Mantenimiento del sistema de refrigeración por aire

•

Limpie las aberturas del refrigerador de aceite

Intervalos de 600 horas

• Cambie el filtro de seguridad (si está equipado).

Limpie más frecuentemente en condiciones polvorientas o cuando haya residuos

transportados por aire.

Cada tres cambios de filtro de aire, sustituya el filtro de seguridad interno (si está

equipado).

Sistema de inyección de combustible electrónica

(EFI)

El sistema EFI controla la temperatura del motor, la velocidad del motor y el voltaje de

la batería para el arranque y el calentamiento del motor. El sistema no tiene ajustes. Si

hay problemas de arranque u operación, póngase en contacto con un distribuidor de

servicio autorizado de Briggs & Stratton.

AVISOAsegúrese de obedecer los pasos que figuran a continuación pues de lo

contrario podría presentarse daño en el sistema EFI.

• NO arranque el motor si los cables de la batería están flojos.

• Gire la llave a la posición APAGADO antes de desconectar, retirar y/o instalar la

batería.

• NO use un cargador de baterías para arrancar el motor.

• NO desconecte los cables de la batería durante la operación del motor.

• Cuando desconecte los cables de la batería, conecte el cable positivo (+)

primero y, luego conecte el cable negativo (-) a la batería.

• Cuando se cargue la batería, gire el interruptor de encendido a la posición

APAGADO y desconecte el cable negativo (-) de la batería.

• NO rocíe con agua el módulo de control electrónico.

Carburador y velocidad del motor

No haga ajustes en el carburador o en la velocidad del motor. El carburador fue

ajustado en la fábrica para operar satisfactoriamente en la mayoría de las condiciones.

No cambie el resorte del gobernador, los enlaces u otras partes para ajustar la

velocidad del motor. Si se requiere algún ajuste, comuníquese con un distribuidor de

servicio autorizado de Briggs & Stratton para solicitar el servicio.

AVISO

El fabricante del equipo especifica la velocidad máxima del motor tal y como está

instalado en el equipo. No exceda esta velocidad. Si no está seguro de la velocidad

máxima del equipo o de la velocidad del motor predeterminada de fábrica, póngase en

contacto con un distribuidor de servicio autorizado de Briggs & Stratton para obtener

ayuda. Para una operación segura y correcta del equipo, la velocidad del motor solo

debe ajustarse por un técnico de servicio calificado.

Mantenimiento de las bujías

Verifique la separación entre bujías (A, Figura8) con un calibrador de bujías (B). Si

es necesario, ajuste la separación entre bujías. Instale y apriete la bujía con el par

de torsión correcto. Para obtener información acerca de las especificaciones de la

separación o del par de torsión, consulte la sección Especificaciones.

Not for

Reproduction

NOTA:En algunas áreas, la legislación local obliga a que se utilice una bujía con

resistor para disminuir las señales de ignición. Si el fabricante del equipo instaló una

bujía con resistor, utilice el mismo tipo para su reemplazo.

Mantenimiento del sistema de escape