Axis Communications 209 FD-R M12 Manuel utilisateur

ENGLISH

FRANCAIS

DEUTSCH

ESPAÑOL

ITALIANO

AXIS 209FD/FD-R/FD-R M12

AXIS 209MFD/MFD-R/MFD-R M12

Installation Guide

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 3

ENGLISH

AXIS 209FD/FD-R/FD-R M12/MFD/

MFD-R/MFD-R M12

Installation Guide

This installation guide provides instructions for installing the AXIS 209FD, AXIS 209FD-R,

AXIS 209FD-R M12, AXIS 209MFD, AXIS 209MFD-R and the AXIS 209MFD-R M12 on

your network. For all other aspects of using the product, please see the User’s Manual,

available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Install the hardware. See page 5.

4. Set an IP address. See page 7.

5. Set the password. See page 10.

6. Adjust the lens. See page 12.

7. Complete the installation. See page 13.

Package contents

Item Models/variants/notes

Fixed Dome Network camera AXIS 209FD

AXIS 209FD-R

AXIS 209FD-R M12

AXIS 209MFD

AXIS 209MFD-R

AXIS 209MFD-R M12

PoE Midspan Power over Ethernet midspan (1 port), including mains cable

(AXIS 209FD/AXIS 209FD-R/AXIS 209MFD/AXIS 209MFD-R)

(midspan not included in bulk pack)

Mounting kit Allen key (hex key) for tamper-proof cover screws

Silica gel sachet (AXIS 209FD-R/AXIS 209FD-R M12/AXIS 209MFD-R/AXIS

209MFD-R M12 only)

CD AXIS Network Video Product CD, including product documentation,

installation tools and other software

Printed Materials AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide (this

document)

Axis Warranty Document

Important!

This product must be used in

compliance with local laws

and regulations.

Page 4 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

Hardware overview

Dimensions

Diameter 1 = 102mm (4.02”), Diameter 2 = 100mm (3.94”)

Height = 39mm (1.54”)

Weight = 0.18 kg (0.40lb)

Front view

Rear view

Side view

Position of rear cable

exit (optional)

Base plate

Network cable with

model-specific

connector

Screw holes

∅102mm

∅100mm

39mm

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 5

ENGLISH

Install the hardware

Mount the camera

The AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 can be mounted with the cable

routed through the ceiling or from the side.

The AXIS 209FD/AXIS 209MFD is

supplied with a standard RJ-45 female

network connector, on a 2 meter cable.

The AXIS 209FD-R/AXIS 209MFD-R is

supplied with a 29mm female RJ-45

network connector on a 0.5 meter cable.

To protect the cabling against moisture

this connecter must be connected to a

suitable 29mm male connector.

The AXIS 209FD-R M12/AXIS 209MFD-

R M12 is supplied with a 21mm male

M12 D-code network connector on a 0.5

meter cable. To protect the cabling

against moisture this connecter must be

connected to a suitable 21mm female

connector.

1. Using the supplied allen/hex key,

loosen the 4 screws holding the

cover and remove it.

2. Use the base plate to mark out the

positions for the mounting screws.

3. To route the cable through a ceiling,

cut or drill the hole for the cable and connector.

For the AXIS 209FD/AXIS 209MFD - cut a 17mm hole.

For the AXIS 209FD-R/AXIS 209MFD-R - cut a 30mm hole.

For the AXIS 209FD-R M12/AXIS 209MFD-R M12 - cut a 22mm hole.

-or-

For a surface mounted cable, cut out the cable exit hole at the rear of the cover

!

IMPORTANT! - The casing of the AXIS 209FD/AXIS 209MFD is not approved

for outdoor use and may only be installed in indoor environments.

The AXIS 209FD-R/AXIS 209FD-R M12/AXIS 209MFD-R/AXIS 209MFD-R

M12 is rugged and can be used in humid environments such as mass transit

vehicles.

Page 6 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

4. Connect the network cable. If

PoE is not supported by the

network switch, use the

supplied PoE midspan/power

injector to connect power to

the AXIS 209FD, AXIS 209FD-

R, AXIS 209MFD, AXIS

209MFD-R.

5. Check that the indicator LED:s

indicate the correct conditions.

See the table on page 15 for

further details.

6. Fasten the base plate to a flat

ceiling, using appropriate

screws/plugs.

Check that the base plate

completely covers the cable

hole, so that it is not visible

when the camera is in place.

Before replacing the cover, you should now make the final adjustment to the position of the

lens. This requires access to live images from the camera in your browser, so you should now

proceed as follows:

a) Assign an IP address - see step 4 on page 7.

b) Set the password - see step 5 on page 10.

c) Adjust the lens - see step 6 on page 12.

d) Complete the installation - see step 7 on page 13.

Network

cable with

connector

Indicator LEDs

Screw hole

Product ID & Serial

number (S/N) label

Screw hole

Control button

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 7

ENGLISH

Assign an IP address

To make it accessible on the network, the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-

R M12 must be assigned an IP address.

Depending on the number of cameras you wish to install, the recommended method for

assigning IP addresses in Windows is either AXIS IP Utility or AXIS Camera Management.

Use the method that best suits your purpose.

Both of these free applications are available on the Axis Network Video Product CD supplied

with this product, or they can be downloaded from www.axis.com/techsup

Notes:

• If there is a DHCP server on your network the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12

will automatically receive a dynamic IP address, but this will not prevent manual setting of an

alternative address.

• The AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 has the default IP address 192.168.0.90

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address, e.g. in other operating systems, see

page 14.

Method Recommended for Operating system

AXIS IP Utility

See page 8

Single camera

Small installations

Windows

AXIS Camera Management

See page 9

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows Vista

Page 8 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

AXIS IP Utility - single camera/small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. The

application can also be used to manually assign a static IP address.

Note that the computer running AXIS IP Utility must be on the same network segment

(physical subnet) as the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12.

Automatic discovery

1. Check that the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 is connected to

the network and that power has been applied.

2. Start AXIS IP Utility.

3. When the camera appears in the window, double-click it to open its home page.

4. See page 10 for instructions on how to assign the password.

Assign the IP address manually (optional)

1. Acquire an unused IP address on the same network segment as your computer.

2. Select the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 in the list.

3. Click the button Assign new IP address to selected device and enter the IP address.

4. Click the Assign button and follow the instructions.

5. Click the Home Page button to access the camera’s web pages.

6. See page 10 for instructions on how to set the password.

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 9

ENGLISH

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically find and set IP addresses, show connection

status, and manage firmware upgrades for multiple Axis video products.

Set the IP address for a single device

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/

MFD-R M12 appears in the window, double-click it to open the camera’s home page.

3. See page 10 for instructions on how to set the password.

Set the IP address in multiple devices

AXIS Camera Management speeds up the process of assigning IP addresses to multiple

devices, by suggesting IP addresses from a specified range.

1. Select the devices you wish to configure (different models can be selected) and click the

Assign IP button.

2. Select Obtain IP addresses automatically (DHCP), click the Update button and the

program will search in the specified range and suggest an IP address for each device.

-or-

Enter the range of IP addresses, the subnet mask and default router that devices can use

and click the Update button.

Page 10 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

Set the password

When accessing the AXIS 209FD/FD-R/FD-R

M12/MFD/MFD-R/MFD-R M12 for the first

time, the ‘Configure Root Password’ dialog

will be displayed.

1. Enter a password and then re-enter it, to

confirm the spelling. Click OK.

2. Enter the user name root in the dialog as

requested.

Note: The default administrator user name root cannot be deleted.

3. Enter the password as set above, and click OK. If the password is lost, the

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 must be reset to the factory

default settings. See page 15.

4. If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the

video stream in Internet Explorer. You will need administrator rights on the computer to

do this.

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 11

ENGLISH

The Live View page of the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 is

displayed, with links to the Setup tools, which allow you to customize the camera.

Setup - Provides all the tools for configuring

the camera to requirements.

Help - Displays

online help on all

aspects of using

the camera.

Page 12 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

Lens adjustments

Position

To adjust the position of the lens, follow these steps:

1. Open the Live View page in your

web browser.

2. Using the supplied allen key, loosen

the 2 locking screws, as shown here.

3. Insert the allen key into the small

hole in the lens casing.

4. While checking the image in the

Live View page, move the lens to

the desired position.

5. When the camera shows the

required view, gently retighten the

locking screws (torque < 0.4 Nm).

Focus

The focus of the AXIS 209FD/FD-R/FD-

R M12/MFD/MFD-R/MFD-R M12 is set

at the factory from 0.5m to infinity. It

does not normally need adjustment.

To focus on objects closer than 0.5m, or

if for some reason the lens has lost

focus, this can be adjusted in the

following way.

1. Loosen the focus lock screw.

2. Manually rotate the lens to adjust

the focus until the image on the

Live View page is satisfactory.

3. Gently retighten the focus lock

screw.

Locking screw

Insert Allen

key here

Focus lock

screw

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 13

ENGLISH

Complete the installation

1. Clean the dome with a dry soft cloth to remove dust and fingerprints and use a blower to

remove any dust from the lens.

2. To absorb any moisture in the

AXIS 209FD-R/AXIS 209FD-R

M12/AXIS 209MFD-R/AXIS

209MFD-R M12, remove the

supplied silica gel sachet (dry

bag) from the plastic bag and

affix inside the cover, behind

the dome.

3. Replace the cover and gently

tighten the tamper-proof screws

by hand (torque < 0.4 Nm),

using the supplied allen key. In

the AXIS 209FD-R/AXIS

209FD-R M12/AXIS 209MFD-R/

AXIS 209MFD-R M12, take care not to pinch the gasket.

The installation is now complete.

Accessing the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/

MFD-R M12 from the Internet

Once installed, your AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 is accessible on

your local network (LAN). To access the camera from the Internet, network routers must be

configured to allow incoming traffic, which is usually done on a specific port. Please refer to

the documentation for your router for further instructions. For more information on this and

other topics, visit the Axis Support Web at www.axis.com/techsup

Affix dry bag here.

Page 14 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address.

All methods are enabled by default, and all can be disabled.

Set the IP address with ARP/Ping

1. Acquire an IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R

M12 label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the camera and then start/restart the

camera, by disconnecting and reconnecting power.

5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter

on your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Use in operating

system

Notes

UPnP™

Windows When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour

MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping

All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00

temp

ping -s 408 192.168.0.125

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide Page 15

ENGLISH

LED indicators

Unit connectors

(AXIS 209FD/AXIS 209MFD) Network connector - Female RJ-45 Ethernet connector for

10BaseT/100BaseTX. Supports Power over Ethernet. Using shielded cables is recommended.

(AXIS 209FD-R/AXIS 209MFD-R) Network connector - Rugged female RJ-45 connector.

Supports Power over Ethernet. Using shielded cables is recommended

(AXIS 209FD-R M12/AXIS 209MFD-R M12) Network connector - Rugged male M12

Ethernet connector. Supports Power over Ethernet. Using shielded cables is recommended.

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Note: The Status LED can be configured to be unlit during normal operation, or to

flash only when the camera is accessed. To configure, go to Setup > System

Options > LED settings. See the online help files for more information.

Amber Steady during startup, during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

Page 16 AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Installation Guide

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the Factory Default settings:

1. Disconnect the network cable from the camera.

2. Using the supplied allen/hex key, loosen the 4 screws holding the cover and remove it.

3. Press and hold the Control button and reconnect the network cable.

4. Keep the Control button pressed until the Status indicator displays amber (this may take

up to 15 seconds).

5. Release the Control button. When the Status indicator displays green (which can take up

to 1 minute) the process is complete and the camera has been reset.

6. Re-assign the IP address, using one of the methods described in this document.

It is also possible to reset parameters to the original factory default settings via the web

interface. For more information, please see the online help or the user’s manual.

Further information

The user’s manual is available from the Axis Web site at www.axis.com or from the Axis

Network Video Product CD supplied with this product.

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your

AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12. To see the currently

installed firmware version, see the Basic Configuration web page in the product’s

Setup tools.

Guide d'installation de l'AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Page 17

FRANÇAIS

FRANCAIS

Guide d'installation de l'AXIS

209FD/FD-R/FD-R M12/MFD/MFD-

R/MFD-R M12

Ce Guide d'installation vous explique comment installer les appareils AXIS 209FD, AXIS

209FD-R, AXIS 209FD-R M12, AXIS 209MFD, AXIS 209MFD-R et AXIS 209MFD-R M12

Fixed Dome Network Camera sur votre réseau. Pour d'autres informations sur l'utilisation de

ce produit, consultez le Manuel de l'utilisateur, disponible sur le CD fourni ou sur

www.axis.com/techsup.

Étapes de l'installation

1. Vérifiez le contenu de la livraison à l'aide de la liste ci-dessous.

2. Présentation du matériel. Reportez-vous à la page 18.

3. Installation du matériel. Reportez-vous à la page 19.

4. Paramétrez une adresse IP. Reportez-vous à

page 21.

5. Définissez le mot de passe. Reportez-vous à

page 24.

6. Réglez l'objectif. Reportez-vous à la page 26.

7. Terminez l'installation. Reportez-vous à la page 27.

Contenu de l'emballage

Article Modèles/variantes/remarques

Caméra réseau à dôme fixe AXIS 209FD, AXIS 209FD-R, AXIS 209FD-R M12

AXIS 209MFD, AXIS 209MFD-R, AXIS 209MFD-R M12

Midspan PoE Midspan Power over Ethernet (1 port), câble de secteur fourni

(AXIS 209FD/AXIS 209FD-R/AXIS 209MFD/AXIS 209MFD-R)

(midspan non inclus dans le lot)

Kit de montage Clé hexagonale pour vis inviolables

Sachet de gel de silice (AXIS 209FD-R/AXIS 209FD-R M12/AXIS 209MFD-R/

AXIS 209MFD-R M12 uniquement)

CD CD AXIS Network Video Product avec la documentation du produit, les outils

d'installation et d'autres logiciels

Documentation imprimée Guide d'installation de l'AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R

M12 (le présent document)

Document de garantie d'Axis

Important !

Ce produit doit être utilisé

conformément aux lois et

dispositions locales en

vigueur.

Page 18 Guide d'installation de l'AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12

Présentation du matériel

Dimensions

Diamètre 1 = 102 mm, diamètre 2 = 100 mm

Hauteur = 39 mm

Poids = 0,18 kg

Vue avant

Vue arrière

Vue latérale

Position de la sortie

arrière du câble

(facultatif)

Plaque de base

Câble réseau avec

connecteur propre à

chaque modèle

Trous de vis

∅102mm

∅100 mm

39 mm

Guide d'installation de l'AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 Page 19

FRANÇAIS

FRANCAIS

Installation du matériel

Montage de la caméra

L'AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12 peut être montée avec le câble

acheminé dans le plafond ou par le côté.

L'AXIS 209FD/AXIS 209MFD est

équipée d'un connecteur de réseau

femelle RJ-45 standard, sur un câble de

2 mètres.

L'AXIS 209FD-R/AXIS 209MFD-R est

équipée d'un connecteur de réseau RJ-

45 femelle de 29 mm sur un câble de 0,5

mètre. Afin de protéger le câblage de

l'humidité, il est nécessaire de relier ce

connecteur à un connecteur mâle de 29

mm.

L'AXIS 209FD-R M12/AXIS 209MFD-R

M12 est équipée d'un connecteur de

réseau M12 D-code mâle de 21 mm sur

un câble de 0,5 mètre. Afin de protéger

le câblage de l'humidité, il est nécessaire

de relier ce connecteur à un connecteur

femelle de 29 mm.

1. Á l'aide de la clé hexagonale four-

nie, desserrez les 4 vis du couvercle

et retirez ce dernier.

2. Utilisez la plaque de base pour marquer la position des vis de montage.

3. Pour acheminer le câble dans un plafond, découpez ou percez le trou destiné au câble et

au connecteur.

Pour l'AXIS 209FD/AXIS 209MFD, découpez un trou de 17 mm.

Pour l'AXIS 209FD-R/AXIS 209MFD-R, découpez un trou de 30 mm.

Pour l'AXIS 209FD-R M12/AXIS 209MFD-R M12, découpez un trou de 22 mm.

-ou-

Pour un câble en saillie, découpez l'orifice de sortie du câble à l'arrière du couvercle.

!

IMPORTANT ! - Le boîtier de l'AXIS 209FD/AXIS 209MFD n'est pas conçu

pour une utilisation en extérieur et ne doit être installé qu'à l'intérieur.

L'AXIS 209FD-R/AXIS 209FD-R M12/AXIS 209MFD-R/AXIS 209MFD-R M12

est consolidée et peut être utilisée dans des environnements humides.

Page 20 Guide d'installation de l'AXIS 209FD/FD-R/FD-R M12/MFD/MFD-R/MFD-R M12

4. Connectez le câble réseau. Si

l'alimentation PoE n'est pas

prise en charge par le

commutateur réseau, utilisez le

midspan PoE fourni pour

brancher l'AXIS 209FD/FD-R/

FD-R M12/MFD/MFD-R/MFD-

R M12.

5. Vérifiez que les témoins DEL

indiquent les conditions

correctes. Pour plus

d'informations, consultez le

tableau à la page 29.

6. Fixez la plaque de base au

plafond à l'aide des vis/

chevilles appropriées.

Vérifiez que la plaque de base

recouvre entièrement le trou

du câble afin qu'il ne soit pas

visible une fois la caméra en place.

Avant de replacer le couvercle, procédez au réglage final de la position de l'objectif. Vous

devez pour cela accéder en direct aux images prises par la caméra dans votre navigateur

Web ; procédez de la manière suivante :

a) Attribuez-lui une adresse IP (étape 4 page 21).

b) Définissez le mot de passe (étape 5 page 24).

c) Réglez l'objectif (étape 6 page 26).

d) Terminez l'installation (étape 7 page 27).

Câble de

réseau avec

connecteur

Témoins DEL

Trou de vis

Étiquette ID du

produit et numéro de

série (S/N)

Trou de vis

Bouton de commande

La page charge ...

Axis Communications 209 FD-R M12 Manuel utilisateur

Ce manuel convient également à

Axis Communications 209 FD-R M12 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents