Blue Wave SA1309 Le manuel du propriétaire

OWNER’S MANUAL

WITH CERAMIC OR CARBON HEATERS

SA2400/SA2406/SA2409/SA1309

Rev. 5/16, Ver. 5

Please Do Not Hesitate to

Contact Our Consumer Hotline

at

800-759-0977

with Any Questions That May

Arise During Assembly or

Use of This Product!

2

ASSEMBLY TIPS & WARNINGS

PARTS IDENTIFIER

ASSEMBLY INSTRUCTIONS

OPERATION INSTRUCTIONS

ENJOYING YOUR SAUNA

HEALTH & SAFETY WARNINGS

CLEANING & MAINTANENCE

TROUBLESHOOTING GUIDE

REPLACEMENT PARTS

WARRANTY INFORMATION

3

4

5-10

11

12

13

14

14-15

16-23

24

TABLE OF CONTENTS

The information contained in this manual is subject to change without notice.

3

• Before you begin, read all assembly instructions and safety warnings carefully.

• This sauna requires at least 2 adults to complete assembly.

• Remove all of the contents from boxes and verify that you have all of the parts shown on the Parts

Note: Some parts may be pre-installed or pre-assembled.

may not look exactly like your product.

• Retain this Owner’s Manual for future reference.

ELECTRICAL REQUIREMENTS

• We recommend consulting a licensed electrician and checking local ordinances before installing

ANY sauna.

• This sauna requires a standard 15 amp receptacle.

• This sauna requires a dedicated circuit - No other appliances should share the same outlet with the

sauna.

CHOOSING A LOCATION

• This sauna should only be placed INDOORS on a dry, level surface.

• There should be a minimum of 5 inches clearance between the sauna and any wall.

• Make sure the main power cord will reach the outlet and remains easy to access.

• The sauna should only be used in a dry location as moisture will damage the wood and electrical

components.

combustible materials.

ASSEMBLY TIPS & WARNINGS

PARTS IDENTIFIER (NOT TO SCALE)

4

2

This manual is used for the assembly of several

sauna models; therefore, some images or drawings

may not look exactly like your product.

ASSEMBLY INSTRUCTIONS

1. Begin assembly by determining an appropriate location for your sauna – see ASSEMBLY

TIPS & WARNINGS for details. Attach the BACK PANEL to the FLOOR by lining up the BACK

PANEL with the groove in the back of the FLOOR.

2. Attach the LEFT PANEL to the FLOOR. Buckle the LEFT PANEL to the BACK PANEL.

3. Attach the RIGHT PANEL to the FLOOR. Buckle the RIGHT PANEL to the BACK PANEL.

5

ASSEMBLY INSTRUCTIONS (CONT.)

4. Carbon Heater Models Only: Attach the FLOOR HEATER to the FLOOR with 1-1/2” SCREWS.

Connect the heater plug.

5. Slide the BENCH HEATER PANEL into place between the LEFT and RIGHT PANELS. Connect

the heater plug. Note: For Carbon Heater Models, make sure the FLOOR HEATER cable is placed

through the groove in the bottom of the BENCH HEATER PANEL.

6. Attach BENCH SEAT with 2” SCREWS.

6

NOTE: When performing Step 5 above, you may need to skew the wall out slightly to accommodate

inserting the BENCH HEATER PANEL.

7. Ceramic Heater Models Only: Attach BACK PANEL HEATER COVER to BACK PANEL with 2”

SCREWS and to BENCH SEAT with 3/4” SCREWS.

8. Attach the FRONT PANEL to the FLOOR. Buckle the FRONT PANEL to the LEFT and RIGHT

PANELS.

9. Lift the ROOF above the sauna, feeding the control panel and heater cables through the

corresponding holes. Feed the cables for the AM/FM CD PLAYER through the hole in the bot-

tom of the ROOF.

Secure the

ROOF to the sauna with 1-1/8” SCREWS. Connect the control panel and heater plugs.

ASSEMBLY INSTRUCTIONS (CONT.)

7

ASSEMBLY INSTRUCTIONS (CONT.)

11. Attach the DOOR HANDLE to the GLASS DOOR.

12. Gently pull the cables for the AM/FM CD PLAYER through the opening in the front of the

STEREO SHELF. Attach the STEREO SHELF with 3/4” SCREWS.

8

10. Feed the main power cable through hole in ROOF and plug securely into receptacle on back

of POWER SUPPLY box . Secure the ROOF COVER with 3/4” SCREWS.

ASSEMBLY INSTRUCTIONS (CONT.)

13. Plug the controller and antenna into the back of the AM/FM CD PLAYER. Slide and lock the

AM/FM CD PLAYER into the STEREO SHELF.

14. Attach the MAGAZINE RACK with 1-1/2” SCREWS. Note: A sticker indicates the optimal posi-

tion for this accessory, but attaching it is optional. Consider the position carefully before driving

any screws into the sauna interior.

15. Attach the CUP HOLDER(S) with 3/4” SCREWS. Note: A sticker indicates the optimal position

for this accessory, but attaching it is optional. Consider the position carefully before driving any

screws into the sauna interior.

16. Two-Person Models Only: Attach the DOUBLE TOWEL HOOK with 3/4” SCREWS. Note: A

sticker indicates the optimal position for this accessory, but attaching it is optional. Consider the

position carefully before driving any screws into the sauna interior.

17. Two-Person Models Only: Attach the COLOR THERAPY CONTROL PANEL into the desig-

nated position with 2” SCREWS.

9

ASSEMBLY INSTRUCTIONS (CONT.)

18. Two-Person Models Only: Remove the back cover of the OXYGEN IONIZER by turning is as

indicated. Unwrap and install the fragrance patch, then reattach the back cover. Attach the

OXYGEN IONIZER in the designated position with 3/4” SCREWS. Plug the power cable into the

OXYGEN IONIZER.

19. Plug the main power cable into a dedicated outlet. Note: No other appliances should share

the same outlet with this sauna.

The assembly of your sauna is now complete.

Please review the Operation Instructions and Health & Safety warnings before using your

sauna.

To ensure years of trouble-free use, follow the Cleaning & Maintenance guidelines carefully.

10

CONGRATULATIONS!

OPERATION INSTRUCTIONS

SAUNA CONTROL PANEL

Note: The sauna controls are the same for both the interior and exterior Control Panels.

1. Press POWER to turn ON the sauna.

2. Set the desired TEMPERATURE with the (+) and (-) buttons.

3. Press and hold both (+) and (-) to switch between °F (Fahrenheit) and °C (Celsius).

4. Set the desired TIME with the (+) and (-) buttons.

6. When the TIME reaches 00, the heaters will turn OFF automatically.

7. After your sauna session, press POWER to turn OFF the sauna.

1. Press POWER to turn ON the Color Therapy Light. The Color Therapy Light will cycle

through all the available colors.

2. Press SELECT to locate your preferred color or pattern, then press SET.

3. Set the desired TIME with the (+) and (-) buttons, then press SET.

4. Press POWER to turn OFF the Color Therapy Light.

1. Press ION to release negatively charged ions to purify the air.

2. Press O3 to disinfect the air with ozone.

11

COLOR THERAPY CONTROL PANEL (Two-Person Models Only)

OXYGEN IONIZER (Two-Person Models Only)

ENJOYING YOUR SAUNA

1. Prior to initial use, wipe down all interior surfaces of the sauna with a damp cloth.

3. Always drink plenty of water before, during and after your sauna session to stay properly

hydrated.

4. A normal sauna session should last 30 minutes or less.

5. Allow approximately 15 to 25 minutes for the sauna to warm up before entering.

6. Perspiration will begin within 15 to 25 minutes after entering the sauna.

7. Limit the use of lotions or oils on your body while using your sauna. These products can

8. For spot treatment of a particular area, position that body part closer to the heater, allow-

ing for deeper heating in that area.

-

spiration and maintain the cleanliness of your sauna.

freely.

11. Open the ceiling vent or the front door to allow fresh air into your sauna.

12. Allow your body to cool down following your sauna session, then rinse the perspiration

12

HEALTH & SAFETY WARNINGS

1. Review all instructions and warnings before operating your sauna. A sauna is not a toy. Seri-

ous injury may result from negligence, intentional misuse and failure to follow safety instruc-

tions.

2. Hyperthermia Danger: Hyperthermia occurs when the body absorbs more heat than it can

emergency and requires immediate treatment to prevent disability or death. It is very impor-

tant not to allow your body’s core temperature to rise above 103° F. Symptoms of hyperthermia

failure to perceive heat, failure to recognize the need to exit the sauna, unawareness of the im-

pending health hazard, physical inability to exit the sauna and unconsciousness.

3. If you are feeling uncomfortable, faint or dizzy, exit the sauna immediately.

4. Do not exceed recommended time and temperature guidelines.

5. Do not touch or interfere with the temperature sensor on the control panel.

6. Do not touch or spray water on the heater elements.

8. Do not sleep inside the sauna.

9. Do not use the sauna immediately following strenuous exercise. Allow your body to cool

down for 30 minutes before entering the sauna.

10. Pets should never be placed in the sauna.

sauna.

12. Children over the age of 6 should always be supervised by an adult.

13. People with health problems including open wounds, fever, sunburn or dehydration should

not use the sauna.

circulatory system problems or diabetes should consult a physician before using the sauna.

15. Consult a physician before using the sauna if you take any prescription medications.

16. Keep towels and combustible materials away from the heater elements.

17. Remove all towels and materials after your sauna session.

18. Never leave your sauna unattended while in use.

19. Always unplug the sauna and allow it to cool down before performing any cleaning or main-

tenance.

13

CLEANING & MAINTENANCE

1. Always unplug the sauna and allow it to cool down before performing any cleaning or

maintenance.

2. Use furniture polish or furniture oil when cleaning the sauna exterior.

3. The sauna interior surfaces should only be wiped down with a damp cloth. Do NOT use

4. As with all natural wood products, variations in the color and the grain as well as irregu-

natural beauty of the wood and should not be considered defective.

14

WARNING!

1. Check that the Main Power Cable is plugged into the wall outlet.

2. Check that the circuit breaker for the outlet has not tripped. If the breaker has tripped, check that the

amperage of the breaker is appropriate for your sauna.

3. Check all connections to the Power Supply Box.

4. Check for damage to the Main Power Cable; replace, if necessary.

5. Replace the Power Supply Box, if necessary.

1. Check that all the connections are tight.

2. Replace the Heater Element.

1. Check that all connections are tight.

2. Replace the Heater Circuit Board, if necessary.

Problem

Solution

Problem

THERE IS NO POWER TO THE SAUNA

ONE HEATER DOES NOT WORK

NONE OF THE HEATERS WORK

TROUBLESHOOTING GUIDE

• Always unplug the sauna and allow it to cool down before performing any maintenance.

• Unauthorized repairs or alterations will void the manufacturer’s warranty.

TROUBLESHOOTING GUIDE (CONT.)

15

1. Check that all the connections are tight.

2. If the numbers are scrambled or the buttons are unresponsive, replace the Control Panel.

3. If the temperature indicator does not work or reads “--” or “EP”, replace the Control Panel.

1. Check that all the connections are tight.

2. If one light does not work, replace the bulb.

during installation.

3. If neither the lights nor the radio are working, replace the Power Supply Box.

1. Check that all the connections are tight.

2. Check the fuse; replace if necessary.

3. Replace the radio.

4. If neither the radio nor the lights are working, replace the Power Supply Box.

1. Check that the volume is not turned all the way down and that the fader control is set correctly.

2. If only one speaker is working, check to see that the sound balance on the stereo is not set all the way

to one side.

3. Check that all the connections are tight.

4. Replace the speaker, if necessary.

1. Check that all the connections are tight.

2. Replace the Color Therapy Light or Color Therapy Control Panel, if necessary.

Problem

THE CONTROL PANEL DOES NOT WORK

THE LIGHTS ARE NOT WORKING

THE RADIO AND/OR CD PLAYER IS NOT WORKING

THE SPEAKERS ARE NOT WORKING

THE COLOR THERAPY LIGHTS ARE NOT WORKING

Solution

REPLACEMENT PARTS

the top of each page to make sure you’re using the correct list for your sauna. In the event that you need replacement

manufacturer. The use of unauthorized substitutes may damage your sauna or cause electrical hazards resulting in

16

R E PL ACE ME NT PAR TS R ev . 5/ 1 6

R E F . # DE S CR I PTI ON PAR T NUMB E R

1 GLASS DOOR SAP24394

1 GLASS CLIP - METAL SAP2537

1 DOOR MAGNET SAP25371

2 FRONT PANEL with GLASS DOOR SAP26164

3 BACK PANEL SAP26193

5 LEFT PANEL SAP2617

6 MAGAZINE RACK SAP2414

7 RIGHT PANEL SAP2618

8 ROOF SAP26205

9 ROOF COVER SAP2601

SAP2503

11 BENCH SEAT SAP2504

12 FLOOR SAP2505

14 AM/FM CD PLAYER with

MP3 INPUT SAP24085

15 DOOR HANDLE SAP2413

16 CONTROL PANEL SAP2406

17 MAIN POWER CABLE SAP2703

18 CUP HOLDER SAP2444

19 DOOR HINGE SAP24154

21 SPEAKER SAP2416

22 THERMOSTAT WIRE SAP25314

24 INTERIOR LIGHT BULB SAP2404

24 LIGHT HOUSING SAP2606

25 POWER SUPPLY BOX SAP24071

25 POWER SUPPLY RECEPTACLE SAP24073

25 HEATER CIRCUIT BOARD SAP2428

25 20 AMP OVERCURRENT PROTECTOR SAP2529

26 STEREO SHELF SAP24024

28 PANEL HEATER COVER SAP3126

29 BACKREST SAP2412

30 350W HEATER ELEMENT – BACK HEATER SAP2423

30 350W HEATER ELEMENT – BENCH HEATER SAP2423

31 2” (50mm) SCREW SAP2411

31 1-1/2” (40mm) SCREW SAP2411

31 1-1/8” (30mm) SCREW SAP2411

31 3/4” (20mm) SCREW SAP2411

--- BUCKLE SAP2607

Please see drawing on next page to assist in identifying parts.

S A2 4 00 ONE -PE R S ON HE ML OCK S AUNA W I TH CE R AMI C HE ATE R S

---

WOODEN POWER CABLE COVER

CONTROL PANEL WIRE (SHORT)

SAP3128

SAP2536

QTY .

1

2

1

1 SET

1

2

1

2

1

2

4

8

18

12

1

10 BENCH HEATER PANEL

--- CONTROL PANEL WIRE (LONG) SAP25361

1

SA2400

17

18

R E PL ACE ME NT PAR TS R ev . 5/ 1 6

R E F . # DE S CR I PTI ON PAR T NUMB E R

1 GLASS DOOR SAP24574

1 GLASS CLIP - METAL SAP2537

1 DOOR MAGNET SAP25371

2 FRONT PANEL with GLASS DOOR SAP26294

3 BACK PANEL SAP26323

5 LEFT PANEL SAP2630

6 350W HEATER ELEMENT – BACK PANEL SAP2423

7 RIGHT PANEL SAP2631

8 ROOF SAP26335

9 ROOF COVER SAP2609

10 BENCH HEATER PANEL SAP2635

11 BENCH SEAT SAP2667

12 FLOOR SAP2634

13 COLOR THERAPY LIGHT SAP2410

14 AM/FM CD PLAYER with MP3 INPUT SAP24085

15 DOOR HANDLE SAP2413

16 CONTROL PANEL SAP2406

18 EXTERIOR LIGHT BULB SAP2404

18, 23 LIGHT HOUSING SAP2606

19 DOOR HINGE SAP24154

20 COLOR THERAPY CONTROL PANEL SAP2427

20 COLOR THERAPY CONTROL PANEL FRAME SAP2417

21 SPEAKER SAP2416

22 THERMOSTAT WIRE SAP25314

23 INTERIOR LIGHT BULB SAP2404

24 MAIN POWER CABLE SAP2703

25 POWER SUPPLY BOX SAP24071

25 POWER SUPPLY RECEPTACLE SAP24073

25 HEATER CIRCUIT BOARD SAP2428

25 20 AMP OVERCURRENT PROTECTOR SAP2529

26 STEREO SHELF SAP24024

27 OXYGEN IONIZER SAP2409

28 BACKREST SAP2412

29 PANEL HEATER COVER SAP3127

31 330W HEATER ELEMENT – LEFT PANEL SAP2424

31 330W HEATER ELEMENT – RIGHT PANEL SAP2424

31 330W HEATER ELEMENT – BENCH PANEL SAP2424

32 DOUBLE TOWEL HOOK SAP2460

33 MAGAZINE RACK SAP2414

34 CUP

HOLDER SAP2444

35 2” (50mm) SCREW SAP2411

35 1-1/2” (40mm) SCREW SAP2411

35 1-1/8” (30mm) SCREW SAP2411

35 3/4” (20mm) SCREW SAP2411

--- BUCKLE SAP2607

--- WOODEN POWER CABLE COVER

SAP3128

Please see drawing on next page to assist in identifying parts.

S A2 4 06 TW O-PE R S ON HE ML OCK S AUNA W I TH CE R AMI C HE ATE R S

---

COLOR THERAPY CONTROL PANEL 4 PRONG WIRE

COLOR THERAPY CONTROL PANEL 5 PRONG WIRE

CONTROL PANEL WIRE (SHORT)

SAP2532

SAP2533

SAP2536

QTY .

1

2

1

2

1

1 SET

1

2

4

2

1

2

1

2

1

2

6

4

6

24

12

1

--- CONTROL PANEL WIRE (LONG) SAP25361

1

SA2406

19

20

REPLACEMENT PARTS Rev. 3/16

REF. # DESCRIPTION PART NUMBER

1 GLASS DOOR SAP24574

1 GLASS CLIP - METAL SAP2537

1 DOOR MAGNET SAP25371

2 FRONT PANEL with GLASS DOOR SAP26364

3 BACK PANEL SAP26394

5 LEFT PANEL SAP26374

6 COLOR THERAPY CONTROL PANEL SAP2427

6 COLOR THERAPY CONTROL PANEL FRAME SAP2417

7 RIGHT PANEL SAP26384

8 ROOF SAP26405

9 ROOF COVER SAP2609

10 BENCH HEATER PANEL SAP26434

11 BENCH SEAT SAP2454

12 FLOOR SAP2641

13 BACKREST SAP2412

14 AM/FM CD PLAYER with MP3 INPUT SAP24085

15 DOOR HANDLE SAP2413

16 CONTROL PANEL SAP2406

17 MAIN POWER CABLE SAP2703

18 EXTERIOR LIGHT BULB SAP2404

18,23 LIGHT HOUSING SAP2606

19 DOOR HINGE SAP24154

20 MAGAZINE RACK SAP2414

21 SPEAKER SAP2416

22 THERMOSTAT WIRE SAP25314

23 INTERIOR LIGHT BULB SAP2404

24,28 330W HEATER ELEMENT – BACK PANEL SAP2418

24,28 330W HEATER ELEMENT – LEFT PANEL SAP2418

24,28 330W HEATER ELEMENT – RIGHT PANEL SAP2418

25 POWER SUPPLY BOX SAP24071

25 POWER SUPPLY RECEPTACLE SAP24073

25 HEATER CIRCUIT BOARD SAP2428

25 20 AMP OVERCURRENT PROTECTOR SAP2529

26 STEREO SHELF SAP24024

27 CUP HOLDER SAP2444

29 COLOR THERAPY LIGHT SAP2410

30

DOUBLE TOWEL HOOK SAP2460

31 FLOOR HEATER SAP2642

32 225W HEATER ELEMENT – BENCH HEATER SA92421

33 180W HEATER ELEMENT – FLOOR HEATER SAP2419

34 OXYGEN IONIZER SAP2409

35 2” (50mm) SCREW SAP2411

35 1-1/2” (40mm) SCREW SAP2411

35 1-1/8” (30mm) SCREW SAP2411

35 3/4” (20mm) SCREW SAP2411

--- BUCKLE SAP2607

--- WOODEN POWER CABLE COVER SAP3128

Please see drawing on next page to assist in identifying parts.

SA2409 TWO-PERSON HEMLOCK SAUNA WITH CARBON HEATERS

QTY.

1

2

1

2

1

1 SET

1

2

4

2

1

2

1

2

1

2

1

4

10

6

24

12

1

---

COLOR THERAPY CONTROL PANEL 4 PRONG WIRE

COLOR THERAPY CONTROL PANEL 5 PRONG WIRE

CONTROL PANEL WIRE (SHORT)

SAP2532

SAP2533

SAP2536

1

--- CONTROL PANEL WIRE (LONG) SAP25361

La page est en cours de chargement...

Blue Wave SA1309 Le manuel du propriétaire

Blue Wave SA1309 Le manuel du propriétaire

dans d''autres langues

Autres documents