Blue Wave BSA1309 Le manuel du propriétaire

Taper
Le manuel du propriétaire
OWNER’S MANUAL
WITH CERAMIC OR CARBON HEATERS
SA2400/SA2406/SA2409/SA1309
Rev. 5/16, Ver. 5
Please Do Not Hesitate to
Contact Our Consumer Hotline
at
800-759-0977
with Any Questions That May
Arise During Assembly or
Use of This Product!
2
ASSEMBLY TIPS & WARNINGS
PARTS IDENTIFIER
ASSEMBLY INSTRUCTIONS
OPERATION INSTRUCTIONS
ENJOYING YOUR SAUNA
HEALTH & SAFETY WARNINGS
CLEANING & MAINTANENCE
TROUBLESHOOTING GUIDE
REPLACEMENT PARTS
WARRANTY INFORMATION
3
4
5-10
11
12
13
14
14-15
16-23
24
TABLE OF CONTENTS
The information contained in this manual is subject to change without notice.
3
Before you begin, read all assembly instructions and safety warnings carefully.
This sauna requires at least 2 adults to complete assembly.
Remove all of the contents from boxes and verify that you have all of the parts shown on the Parts
Note: Some parts may be pre-installed or pre-assembled.
may not look exactly like your product.
Retain this Owners Manual for future reference.
ELECTRICAL REQUIREMENTS
We recommend consulting a licensed electrician and checking local ordinances before installing
ANY sauna.
This sauna requires a standard 15 amp receptacle.
This sauna requires a dedicated circuit - No other appliances should share the same outlet with the
sauna.
CHOOSING A LOCATION
This sauna should only be placed INDOORS on a dry, level surface.
There should be a minimum of 5 inches clearance between the sauna and any wall.
Make sure the main power cord will reach the outlet and remains easy to access.
The sauna should only be used in a dry location as moisture will damage the wood and electrical
components.
combustible materials.
ASSEMBLY TIPS & WARNINGS
PARTS IDENTIFIER (NOT TO SCALE)
4
2
This manual is used for the assembly of several
sauna models; therefore, some images or drawings
may not look exactly like your product.
ASSEMBLY INSTRUCTIONS
1. Begin assembly by determining an appropriate location for your sauna – see ASSEMBLY
TIPS & WARNINGS for details. Attach the BACK PANEL to the FLOOR by lining up the BACK
PANEL with the groove in the back of the FLOOR.
2. Attach the LEFT PANEL to the FLOOR. Buckle the LEFT PANEL to the BACK PANEL.
3. Attach the RIGHT PANEL to the FLOOR. Buckle the RIGHT PANEL to the BACK PANEL.
5
ASSEMBLY INSTRUCTIONS (CONT.)
4. Carbon Heater Models Only: Attach the FLOOR HEATER to the FLOOR with 1-1/2” SCREWS.
Connect the heater plug.
5. Slide the BENCH HEATER PANEL into place between the LEFT and RIGHT PANELS. Connect
the heater plug. Note: For Carbon Heater Models, make sure the FLOOR HEATER cable is placed
through the groove in the bottom of the BENCH HEATER PANEL.
6. Attach BENCH SEAT with 2” SCREWS.
6
NOTE: When performing Step 5 above, you may need to skew the wall out slightly to accommodate
inserting the BENCH HEATER PANEL.
7. Ceramic Heater Models Only: Attach BACK PANEL HEATER COVER to BACK PANEL with 2”
SCREWS and to BENCH SEAT with 3/4” SCREWS.
8. Attach the FRONT PANEL to the FLOOR. Buckle the FRONT PANEL to the LEFT and RIGHT
PANELS.
9. Lift the ROOF above the sauna, feeding the control panel and heater cables through the
corresponding holes. Feed the cables for the AM/FM CD PLAYER through the hole in the bot-
tom of the ROOF.
Secure the
ROOF to the sauna with 1-1/8” SCREWS. Connect the control panel and heater plugs.
ASSEMBLY INSTRUCTIONS (CONT.)
7
ASSEMBLY INSTRUCTIONS (CONT.)
11. Attach the DOOR HANDLE to the GLASS DOOR.
12. Gently pull the cables for the AM/FM CD PLAYER through the opening in the front of the
STEREO SHELF. Attach the STEREO SHELF with 3/4” SCREWS.
8
10. Feed the main power cable through hole in ROOF and plug securely into receptacle on back
of POWER SUPPLY box . Secure the ROOF COVER with 3/4” SCREWS.
ASSEMBLY INSTRUCTIONS (CONT.)
13. Plug the controller and antenna into the back of the AM/FM CD PLAYER. Slide and lock the
AM/FM CD PLAYER into the STEREO SHELF.
14. Attach the MAGAZINE RACK with 1-1/2” SCREWS. Note: A sticker indicates the optimal posi-
tion for this accessory, but attaching it is optional. Consider the position carefully before driving
any screws into the sauna interior.
15. Attach the CUP HOLDER(S) with 3/4” SCREWS. Note: A sticker indicates the optimal position
for this accessory, but attaching it is optional. Consider the position carefully before driving any
screws into the sauna interior.
16. Two-Person Models Only: Attach the DOUBLE TOWEL HOOK with 3/4” SCREWS. Note: A
sticker indicates the optimal position for this accessory, but attaching it is optional. Consider the
position carefully before driving any screws into the sauna interior.
17. Two-Person Models Only: Attach the COLOR THERAPY CONTROL PANEL into the desig-
nated position with 2” SCREWS.
9
ASSEMBLY INSTRUCTIONS (CONT.)
18. Two-Person Models Only: Remove the back cover of the OXYGEN IONIZER by turning is as
indicated. Unwrap and install the fragrance patch, then reattach the back cover. Attach the
OXYGEN IONIZER in the designated position with 3/4” SCREWS. Plug the power cable into the
OXYGEN IONIZER.
19. Plug the main power cable into a dedicated outlet. Note: No other appliances should share
the same outlet with this sauna.
The assembly of your sauna is now complete.
Please review the Operation Instructions and Health & Safety warnings before using your
sauna.
To ensure years of trouble-free use, follow the Cleaning & Maintenance guidelines carefully.
10
CONGRATULATIONS!
OPERATION INSTRUCTIONS
SAUNA CONTROL PANEL
Note: The sauna controls are the same for both the interior and exterior Control Panels.
1. Press POWER to turn ON the sauna.
2. Set the desired TEMPERATURE with the (+) and (-) buttons.
3. Press and hold both (+) and (-) to switch between °F (Fahrenheit) and °C (Celsius).
4. Set the desired TIME with the (+) and (-) buttons.
6. When the TIME reaches 00, the heaters will turn OFF automatically.
7. After your sauna session, press POWER to turn OFF the sauna.
1. Press POWER to turn ON the Color Therapy Light. The Color Therapy Light will cycle
through all the available colors.
2. Press SELECT to locate your preferred color or pattern, then press SET.
3. Set the desired TIME with the (+) and (-) buttons, then press SET.
4. Press POWER to turn OFF the Color Therapy Light.
1. Press ION to release negatively charged ions to purify the air.
2. Press O3 to disinfect the air with ozone.
11
COLOR THERAPY CONTROL PANEL (Two-Person Models Only)
OXYGEN IONIZER (Two-Person Models Only)
ENJOYING YOUR SAUNA
1. Prior to initial use, wipe down all interior surfaces of the sauna with a damp cloth.
3. Always drink plenty of water before, during and after your sauna session to stay properly
hydrated.
4. A normal sauna session should last 30 minutes or less.
5. Allow approximately 15 to 25 minutes for the sauna to warm up before entering.
6. Perspiration will begin within 15 to 25 minutes after entering the sauna.
7. Limit the use of lotions or oils on your body while using your sauna. These products can
8. For spot treatment of a particular area, position that body part closer to the heater, allow-
ing for deeper heating in that area.
-
spiration and maintain the cleanliness of your sauna.
freely.
11. Open the ceiling vent or the front door to allow fresh air into your sauna.
12. Allow your body to cool down following your sauna session, then rinse the perspiration
12
HEALTH & SAFETY WARNINGS
1. Review all instructions and warnings before operating your sauna. A sauna is not a toy. Seri-
ous injury may result from negligence, intentional misuse and failure to follow safety instruc-
tions.
2. Hyperthermia Danger: Hyperthermia occurs when the body absorbs more heat than it can
emergency and requires immediate treatment to prevent disability or death. It is very impor-
tant not to allow your bodys core temperature to rise above 103° F. Symptoms of hyperthermia
failure to perceive heat, failure to recognize the need to exit the sauna, unawareness of the im-
pending health hazard, physical inability to exit the sauna and unconsciousness.
3. If you are feeling uncomfortable, faint or dizzy, exit the sauna immediately.
4. Do not exceed recommended time and temperature guidelines.
5. Do not touch or interfere with the temperature sensor on the control panel.
6. Do not touch or spray water on the heater elements.
8. Do not sleep inside the sauna.
9. Do not use the sauna immediately following strenuous exercise. Allow your body to cool
down for 30 minutes before entering the sauna.
10. Pets should never be placed in the sauna.
sauna.
12. Children over the age of 6 should always be supervised by an adult.
13. People with health problems including open wounds, fever, sunburn or dehydration should
not use the sauna.
circulatory system problems or diabetes should consult a physician before using the sauna.
15. Consult a physician before using the sauna if you take any prescription medications.
16. Keep towels and combustible materials away from the heater elements.
17. Remove all towels and materials after your sauna session.
18. Never leave your sauna unattended while in use.
19. Always unplug the sauna and allow it to cool down before performing any cleaning or main-
tenance.
13
CLEANING & MAINTENANCE
1. Always unplug the sauna and allow it to cool down before performing any cleaning or
maintenance.
2. Use furniture polish or furniture oil when cleaning the sauna exterior.
3. The sauna interior surfaces should only be wiped down with a damp cloth. Do NOT use
4. As with all natural wood products, variations in the color and the grain as well as irregu-
natural beauty of the wood and should not be considered defective.
14
WARNING!
1. Check that the Main Power Cable is plugged into the wall outlet.
2. Check that the circuit breaker for the outlet has not tripped. If the breaker has tripped, check that the
amperage of the breaker is appropriate for your sauna.
3. Check all connections to the Power Supply Box.
4. Check for damage to the Main Power Cable; replace, if necessary.
5. Replace the Power Supply Box, if necessary.
1. Check that all the connections are tight.
2. Replace the Heater Element.
1. Check that all connections are tight.
2. Replace the Heater Circuit Board, if necessary.
Problem
Solution
Solution
Solution
Problem
Problem
THERE IS NO POWER TO THE SAUNA
ONE HEATER DOES NOT WORK
NONE OF THE HEATERS WORK
TROUBLESHOOTING GUIDE
Always unplug the sauna and allow it to cool down before performing any maintenance.
Unauthorized repairs or alterations will void the manufacturer’s warranty.
TROUBLESHOOTING GUIDE (CONT.)
15
1. Check that all the connections are tight.
2. If the numbers are scrambled or the buttons are unresponsive, replace the Control Panel.
3. If the temperature indicator does not work or reads “--” or “EP, replace the Control Panel.
1. Check that all the connections are tight.
2. If one light does not work, replace the bulb.
during installation.
3. If neither the lights nor the radio are working, replace the Power Supply Box.
1. Check that all the connections are tight.
2. Check the fuse; replace if necessary.
3. Replace the radio.
4. If neither the radio nor the lights are working, replace the Power Supply Box.
1. Check that the volume is not turned all the way down and that the fader control is set correctly.
2. If only one speaker is working, check to see that the sound balance on the stereo is not set all the way
to one side.
3. Check that all the connections are tight.
4. Replace the speaker, if necessary.
1. Check that all the connections are tight.
2. Replace the Color Therapy Light or Color Therapy Control Panel, if necessary.
Problem
Problem
Problem
Problem
Problem
THE CONTROL PANEL DOES NOT WORK
THE LIGHTS ARE NOT WORKING
THE RADIO AND/OR CD PLAYER IS NOT WORKING
THE SPEAKERS ARE NOT WORKING
THE COLOR THERAPY LIGHTS ARE NOT WORKING
Solution
Solution
Solution
Solution
Solution
REPLACEMENT PARTS
the top of each page to make sure you’re using the correct list for your sauna. In the event that you need replacement
manufacturer. The use of unauthorized substitutes may damage your sauna or cause electrical hazards resulting in
16
R E PL ACE ME NT PAR TS R ev . 5/ 1 6
R E F . # DE S CR I PTI ON PAR T NUMB E R
1 GLASS DOOR SAP24394
1 GLASS CLIP - METAL SAP2537
1 DOOR MAGNET SAP25371
2 FRONT PANEL with GLASS DOOR SAP26164
3 BACK PANEL SAP26193
5 LEFT PANEL SAP2617
6 MAGAZINE RACK SAP2414
7 RIGHT PANEL SAP2618
8 ROOF SAP26205
9 ROOF COVER SAP2601
SAP2503
11 BENCH SEAT SAP2504
12 FLOOR SAP2505
14 AM/FM CD PLAYER with
MP3 INPUT SAP24085
15 DOOR HANDLE SAP2413
16 CONTROL PANEL SAP2406
17 MAIN POWER CABLE SAP2703
18 CUP HOLDER SAP2444
19 DOOR HINGE SAP24154
21 SPEAKER SAP2416
22 THERMOSTAT WIRE SAP25314
24 INTERIOR LIGHT BULB SAP2404
24 LIGHT HOUSING SAP2606
25 POWER SUPPLY BOX SAP24071
25 POWER SUPPLY RECEPTACLE SAP24073
25 HEATER CIRCUIT BOARD SAP2428
25 20 AMP OVERCURRENT PROTECTOR SAP2529
26 STEREO SHELF SAP24024
28 PANEL HEATER COVER SAP3126
29 BACKREST SAP2412
30 350W HEATER ELEMENT – BACK HEATER SAP2423
30 350W HEATER ELEMENT – BENCH HEATER SAP2423
31 2” (50mm) SCREW SAP2411
31 1-1/2” (40mm) SCREW SAP2411
31 1-1/8” (30mm) SCREW SAP2411
31 3/4” (20mm) SCREW SAP2411
--- BUCKLE SAP2607
Please see drawing on next page to assist in identifying parts.
S A2 4 00 ONE -PE R S ON HE ML OCK S AUNA W I TH CE R AMI C HE ATE R S
---
---
WOODEN POWER CABLE COVER
CONTROL PANEL WIRE (SHORT)
SAP3128
SAP2536
QTY .
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1 SET
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
2
1
2
4
8
18
12
1
1
10 BENCH HEATER PANEL
--- CONTROL PANEL WIRE (LONG) SAP25361
1
SA2400
17
18
R E PL ACE ME NT PAR TS R ev . 5/ 1 6
R E F . # DE S CR I PTI ON PAR T NUMB E R
1 GLASS DOOR SAP24574
1 GLASS CLIP - METAL SAP2537
1 DOOR MAGNET SAP25371
2 FRONT PANEL with GLASS DOOR SAP26294
3 BACK PANEL SAP26323
5 LEFT PANEL SAP2630
6 350W HEATER ELEMENT – BACK PANEL SAP2423
7 RIGHT PANEL SAP2631
8 ROOF SAP26335
9 ROOF COVER SAP2609
10 BENCH HEATER PANEL SAP2635
11 BENCH SEAT SAP2667
12 FLOOR SAP2634
13 COLOR THERAPY LIGHT SAP2410
14 AM/FM CD PLAYER with MP3 INPUT SAP24085
15 DOOR HANDLE SAP2413
16 CONTROL PANEL SAP2406
18 EXTERIOR LIGHT BULB SAP2404
18, 23 LIGHT HOUSING SAP2606
19 DOOR HINGE SAP24154
20 COLOR THERAPY CONTROL PANEL SAP2427
20 COLOR THERAPY CONTROL PANEL FRAME SAP2417
21 SPEAKER SAP2416
22 THERMOSTAT WIRE SAP25314
23 INTERIOR LIGHT BULB SAP2404
24 MAIN POWER CABLE SAP2703
25 POWER SUPPLY BOX SAP24071
25 POWER SUPPLY RECEPTACLE SAP24073
25 HEATER CIRCUIT BOARD SAP2428
25 20 AMP OVERCURRENT PROTECTOR SAP2529
26 STEREO SHELF SAP24024
27 OXYGEN IONIZER SAP2409
28 BACKREST SAP2412
29 PANEL HEATER COVER SAP3127
31 330W HEATER ELEMENT – LEFT PANEL SAP2424
31 330W HEATER ELEMENT – RIGHT PANEL SAP2424
31 330W HEATER ELEMENT – BENCH PANEL SAP2424
32 DOUBLE TOWEL HOOK SAP2460
33 MAGAZINE RACK SAP2414
34 CUP
HOLDER SAP2444
35 2” (50mm) SCREW SAP2411
35 1-1/2” (40mm) SCREW SAP2411
35 1-1/8” (30mm) SCREW SAP2411
35 3/4” (20mm) SCREW SAP2411
--- BUCKLE SAP2607
--- WOODEN POWER CABLE COVER
SAP3128
Please see drawing on next page to assist in identifying parts.
S A2 4 06 TW O-PE R S ON HE ML OCK S AUNA W I TH CE R AMI C HE ATE R S
---
---
---
COLOR THERAPY CONTROL PANEL 4 PRONG WIRE
COLOR THERAPY CONTROL PANEL 5 PRONG WIRE
CONTROL PANEL WIRE (SHORT)
SAP2532
SAP2533
SAP2536
QTY .
1
2
2
1
1
1
2
1
1
1
1
1
1
1
1
1 SET
1
2
4
2
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
6
4
6
24
12
1
1
1
1
--- CONTROL PANEL WIRE (LONG) SAP25361
1
SA2406
19
20
REPLACEMENT PARTS Rev. 3/16
REF. # DESCRIPTION PART NUMBER
1 GLASS DOOR SAP24574
1 GLASS CLIP - METAL SAP2537
1 DOOR MAGNET SAP25371
2 FRONT PANEL with GLASS DOOR SAP26364
3 BACK PANEL SAP26394
5 LEFT PANEL SAP26374
6 COLOR THERAPY CONTROL PANEL SAP2427
6 COLOR THERAPY CONTROL PANEL FRAME SAP2417
7 RIGHT PANEL SAP26384
8 ROOF SAP26405
9 ROOF COVER SAP2609
10 BENCH HEATER PANEL SAP26434
11 BENCH SEAT SAP2454
12 FLOOR SAP2641
13 BACKREST SAP2412
14 AM/FM CD PLAYER with MP3 INPUT SAP24085
15 DOOR HANDLE SAP2413
16 CONTROL PANEL SAP2406
17 MAIN POWER CABLE SAP2703
18 EXTERIOR LIGHT BULB SAP2404
18,23 LIGHT HOUSING SAP2606
19 DOOR HINGE SAP24154
20 MAGAZINE RACK SAP2414
21 SPEAKER SAP2416
22 THERMOSTAT WIRE SAP25314
23 INTERIOR LIGHT BULB SAP2404
24,28 330W HEATER ELEMENT – BACK PANEL SAP2418
24,28 330W HEATER ELEMENT – LEFT PANEL SAP2418
24,28 330W HEATER ELEMENT – RIGHT PANEL SAP2418
25 POWER SUPPLY BOX SAP24071
25 POWER SUPPLY RECEPTACLE SAP24073
25 HEATER CIRCUIT BOARD SAP2428
25 20 AMP OVERCURRENT PROTECTOR SAP2529
26 STEREO SHELF SAP24024
27 CUP HOLDER SAP2444
29 COLOR THERAPY LIGHT SAP2410
30
DOUBLE TOWEL HOOK SAP2460
31 FLOOR HEATER SAP2642
32 225W HEATER ELEMENT – BENCH HEATER SA92421
33 180W HEATER ELEMENT – FLOOR HEATER SAP2419
34 OXYGEN IONIZER SAP2409
35 2” (50mm) SCREW SAP2411
35 1-1/2” (40mm) SCREW SAP2411
35 1-1/8” (30mm) SCREW SAP2411
35 3/4” (20mm) SCREW SAP2411
--- BUCKLE SAP2607
--- WOODEN POWER CABLE COVER SAP3128
Please see drawing on next page to assist in identifying parts.
SA2409 TWO-PERSON HEMLOCK SAUNA WITH CARBON HEATERS
QTY.
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1 SET
1
1
2
4
2
1
2
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
4
10
6
24
12
1
1
1
1
---
---
---
COLOR THERAPY CONTROL PANEL 4 PRONG WIRE
COLOR THERAPY CONTROL PANEL 5 PRONG WIRE
CONTROL PANEL WIRE (SHORT)
SAP2532
SAP2533
SAP2536
1
--- CONTROL PANEL WIRE (LONG) SAP25361
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Blue Wave BSA1309 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues