Danfoss CF-RD Room Thermostat Guide d'installation

Taper
Guide d'installation
088U0212
Instructions CF-RD Room Thermostat with Display
Anleitung CF-RD Raum Thermostat mit Display
Vejledning CF-RD Rumtermostat med display
Instruction CF-RD Thermostat avec e’cran
2
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Instruction . . . . . . . . . . . . . . . . . . . . . . . 3
Anleitung . . . . . . . . . . . . . . . . . . . . . . . 15
Vejledning . . . . . . . . . . . . . . . . . . . . . . 26
Instruction . . . . . . . . . . . . . . . . . . . . . . 37
3VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
1. Functional Overview . . . . . . . . . . . . . . . . . . 4
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Temperature Settings . . . . . . . . . . . . . . . . . 7
4. Transmission Test . . . . . . . . . . . . . . . . . . . . . 9
5. Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6. Uninstallation . . . . . . . . . . . . . . . . . . . . . . . . 11
7. Specications . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 13
9. Figures and illustrations . . . . . . . . . . . . . . . 48-49
Index
4
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Front - g. 1
Up/down selector
Push button
Red LED (behind the cover)
LED modes
Permanent light ON
No light OFF
Slow ashing Flashes
Fast ashing Flickers
Back - g. 2
Back plate
Back plate lock/unlock (turn 90°)
Screw hole for wall mounting
Battery placement
Screw and wall plug
Note: To activate batteries please remove enclosed
strips from batteries
1. Functional Overview
5VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Note:
To activate batteries in the Room Thermostat
please remove enclosed strips from the batteries.
The assignment of the Room Thermostats to the
Master Controller should be within 1½m distance
Activate Install mode on
Master Controller - g. 1.
Use the menu selection button to select the
Install mode. Install LED ashes
Activate Install mode by pressing OK . Install
LED goes ON
Activate Install mode on
Room Thermostat
Press the push button . LED and icker
during communication
Select output on Master Controller
All available output LEDs on Master Controller
light up, and the rst of them ashes
Press output selection button , select desired
output (ashes) and accept with OK
All output LEDs go OFF. Selected output
stays ON shortly
2. Installation
6
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Room Thermostat installation status
Satisfactory - LED goes OFF
Not satisfactory - LED ashes 5 times
Note: A Room Thermostat can be assigned to sev-
eral outputs if needed
7VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Digital Display - g. 1
Set value adjustment
Minimum temperature limitation
Maximum temperature limitation
Lock icon (settings locked from
Remote Controller, CF-RC)
Transmission link icon
Low battery indicator
Alarm icon
Timer icon (time & zone control set
from Remote Controller, CF-RC)
3. Temperature Settings
8
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Setting of Temperatures - g. 1
The actual room temperature is shown in the
display as default
Setting of room temperature
Press the up/down selector to set the de-
sired room temperature value, SET is shown in
the display
When releasing the up/down selector the
display returns to actual room temperature
Room temperature limitation
Press and hold the push button until SET
MAX is shown in the display
Press the up/down selector to set the maxi-
mum room temperature limitation
Press the push button shortly, SET MIN is
shown in the display
Press the up/down selector to set the mini-
mum room temperature limitation
Press the push button shortly, the actual
room temperature is shown in the display
9VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Initiate transmission test on Room
Thermostat - g. 1
Press the push button
LED goes ON
Link test is satisfactory
LED goes OFF
Link test is unsatisfactory
LED ashes 5 times
No Link connection to Room Thermo-
stat
Try to relocate Room Thermostat in the room
Or install Repeater Unit (CF-RU) and locate be-
tween Master Controller and Room Thermostat
Note: Master Controller output LED(s) connect-
ed to the room thermostat, ash(es) during Link test
4. Transmission Test
10
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Placing the Room Thermostat - g. 3
! Wherever possible, the room thermostat should
be installed at a place where the eect of sunlight,
draught, other heaters (eg. TVs), etc. is avoided.
Mounting with screws - g. 2
5. Mounting
11VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Activate Uninstall mode on Master
Controller - g. 1
Use the Menu selection button to choose
the Uninstall menu. Uninstall LED ashes
Activate Uninstall mode by pressing OK .
Uninstall LED goes ON
Deselect output on Master Controller
Select output to be removed by output selection
button
Remove ashing output with OK
6. Uninstallation
12
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Temperature setting
range
5-35°C
Transmission frequency 868.42MHz
Transmission range in
normal buildings (up to)
30m
Transmission power < 1mW
Battery Alkaline 2xAA, 1.5V
Battery lifetime
(up to)
2-3 years
Ambient temperature 0-50°C
IP class 21
7. Specications
13VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
Error Indication Possible Cause
The LED, and
ashes every 5th minute
Low battery
The LED, and
ashes
Critical low battery
The LED, , and
ashes
Critical low battery -
transmission has stopped
The LED, and
ashes 5 times
Installation/Link Test is
unsatisfactory
E03 and
Actuator error on output
(CF-MC)
E05 and
Room temperature below
5ºC
8. Troubleshooting
14
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Instruction CF-RD Room Thermostat with Display
15VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Anleitung CF-RD Raumthermostat mit Display
1. Funktionsübersicht . . . . . . . . . . . . . . . . . . . 16
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3. Temperatureinstellungen . . . . . . . . . . . . . 19
4. Funk - Verbindungstest . . . . . . . . . . . . . . . 21
5. Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
6. Deinstallation . . . . . . . . . . . . . . . . . . . . . . . . 23
7. Technische Daten . . . . . . . . . . . . . . . . . . . . 24
8. Fehlersuche . . . . . . . . . . . . . . . . . . . . . . . . . . 25
9. Bilder und Zeichnungen . . . . . . . . . . . . . . 48-49
Inhaltsverzeichnis
16
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Anleitung CF-RD Raumthermostat mit Display
Vorderseite - Abb. 1
Freie Temperaturwahl
höher/niedriger
Druckknopf
Rote LED (hinter der Abdeckung)
LED-Anzeige
Dauerlicht EIN
Kein Licht
AUS
Langsames Blinken Blinkt
Schnelles Blinken
Flackert
Rückseite - Abb. 2
Hintere Abdeckung
Hintere Abdeckung sperren/entsperren (um
90° drehen)
Schraubenloch für Wandmontage
Batteriepositionierung
Schraube und Dübel
Anmerkung: Zum Aktivieren der Batterien entfern-
en Sie bitte die Trennstreifen von den Batterien.
1. Funktionsübersicht
17VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Anleitung CF-RD Raumthermostat mit Display
Anmerkung:
Zum Aktivieren der Batterien im Raumthermo-
staten entfernen Sie bitte den Trennstreifen von
den Batterien
Die Anmeldung des Raumthermostaten muss
innerhalb von 1,5m vom Hauptregler erfolgen
Aktivieren Sie den Installations-
modus am Hauptregler - Abb. 1
Verwenden Sie die Taste zur Menüauswahl
, um den Installationsmodus zu wählen. Die
Installations-LED blinkt.
Aktivieren Sie den Installationsmodus, indem
Sie auf OK drücken . Die Installations-LED
wechselt zu „EIN“.
Aktivieren Sie den Installationsmo-
dus am Raumthermostaten
Betätigen Sie den Druckknopf . Die LEDs
und ackern während der Kommunikation.
2. Installation
18
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Anleitung CF-RD Raumthermostat mit Display
Wählen Sie den Ausgang am
Hauptregler
Alle verfügbaren Ausgangs-LEDs am
Hauptregler leuchten, und die erste LED
blinkt.
Betätigen Sie die Taste zur Ausgangswahl ,
wählen Sie den gewünschten Ausgang (blinkt),
und bestätigen Sie mit OK .
Alle Ausgangs-LEDs wechseln zu „AUS“. Der
gewählte Ausgang wechselt kurz zu „EIN“.
Installationsstatus des Raumthermo-
staten
Wenn OK - LED wechselt zu „AUS“.
Wenn nicht OK - LED blinkt 5 Mal.
Anmerkung: Ein Raumthermostat kann bei Bedarf
mit mehreren Ausgängen (Stellantrieben) verbun-
den werden.
19VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Anleitung CF-RD Raumthermostat mit Display
Digitale Anzeige - Abb. 1
Temperatureinstellung
Mindesttemperaturbegrenzung
Höchsttemperaturbegrenzung
Symbol Sperre (Einstellungen werden
über die Fernbedienung gesperrt,
CF-RC)
Symbol Funk - Sendeverbindung
Anzeige Batterieladezustand niedrig
Symbol Alarm
Symbol Timer - Zeit und Zonenkon-
trolle über Fernbedienung eingestellt,
CF-RC)
3. Temperatureinstellungen
20
VI.UH.Q1.52
Produced by Danfoss Floor Heating Hydronics 08.2008
Anleitung CF-RD Raumthermostat mit Display
Einstellung der Temperaturen - Abb. 1
Standardmäßig erscheint in der Anzeige die
tatsächliche Raumtemperatur.
Einstellen der Raumtemperatur
Drücken Sie den Temperaturwähler , um die
gewünschte Raumtemperatur einzustellen, SET
erscheint in der Anzeige.
Wenn Sie den Temperaturwähler loslassen,
erscheint in der Anzeige wieder die tatsächli-
che Raumtemperatur.
Raumtemperaturbegrenzung
Halten Sie den Druckknopf gedrückt, bis SET
MAX in der Anzeige erscheint.
Betätigen Sie den Temperaturwähler , um die
maximale Raumtemperatur einzustellen.
Betätigen Sie kurz den Druckknopf , SET MIN
erscheint in der Anzeige.
Betätigen Sie den Temperaturwähler , um die
niedrigste Raumtemperatur einzustellen.
Betätigen Sie kurz den Druckknopf , in der
Anzeige erscheint die tatsächliche Raumtem-
peratur.
1 / 1

Danfoss CF-RD Room Thermostat Guide d'installation

Taper
Guide d'installation