Monument 77252 Le manuel du propriétaire

Liquid Propane Gas Grill

•

Parts

ASSEMBLY & OPERATING INSTRUCTIONS

Note to Consumer

Leave this Owner’s Manual in a convenient

place for future reference.

Customer Service Helpline:

For parts ordering, call:

1- 800-530-9133

MFG No.: 77352

UPC No.: 856597007102

Please make sure the cylinder valve

connection device shall properly and safely

mate with the connection device attached to

the inlet of the pressure regulator.

WARNING:

Read this Owner’s manual carefully and be

sure your gas grill is properly assembled,

installed and maintained. Failure to follow these

instructions could result in serious injury and/or

property damage. This gas grill is intended for

outdoor use only and is not intended to be

installed in or on recreational vehicles or boats.

Note to Installer

Leave this Owner’s Manual with the customer

after delivery and/or installation.

!

•

Parts

•Assembly

•Safety Rules

•Use and Care

•Troubleshooting

C042363-A7

WARNING

Your grill will get very hot. Never lean over the

cooking area while using your grill. Do not touch

cooking surfaces, grill housing, lid or any other

grill parts while the grill is in operation, or until the

gas grill has cooled down after use.

Failure to comply with these instructions may

result in serious bodily injury.

One-Year Full Warranty on Grill

If this grill fails due to defective material or

workmanship within one year from the date of

purchase, call to arrange for a free repair (or

replacement if repair proves impossible).

8-Year Limited Warranty on Stainless Steel

Burners

For eight years from the date of purchase, any

stainless steel burner that rusts through will be

replaced free of charge. After the first year from the

WARNING

Combustion by products produced when using

this product contain chemicals known to the

State of California to cause cancer, birth defects,

or other reproductive harm.

WARNING

Failure to comply with these instructions could

result in a fire or explosion that could cause

serious bodily injury, death, or property damage.

WARNING

1. Do not store or use gasoline or

other flammable liquids or

vapors in the vicinity of this or

any other appliance.

2.

A

n

LP

cylinder not

connected for

!

Grill Warranty

Safety Precautions

!

Table of Contents

Warranty------------------------------------------------2

Safety Precautions--------------------------------2~4

Hardware List------------------------------------------5

Parts Diagram -----------------------------------------6

Parts List------------------------------------------------7

Assembly Instructions---------------------------8~19

Lighting Instructions----------------------------19~21

Cleaning and Maintenance-------------------22~23

Troubleshooting--------------------------------------23

Cooking Instruction----------------------------------24

Cooking Chart----------------------------------------25

replaced free of charge. After the first year from the

date of purchase, you pay for labor if you wish to have

it installed.

All warranty coverage excludes ignitor batteries and

grill part paint loss, discoloration or rusting, which are

either expendable parts that can wear out from normal

use within the warranty period, or are conditions that

can be the result or normal use, accident or improper

maintenance,

All warranty coverage is void if this grill is ever used

for commercial or rental purposes.

All warranty coverage applies only if this grill is used in

the North America.

This warranty gives you specific legal rights, and you

may have other right which vary from state to state.

The warranty is only valid for original purchasers with

proof of purchase from authorized retailers. Any

product bought second hand or through an

unauthorized retailer, will not be covered by

warranty. It is the duty of the purchaser to verify that a

retailer is authorized. A purchase on Amazon or other

marketplace internet retailer from any entity other than

Monument Grills is not an original purchase and will

not qualify for a warranty

2.

A

n

LP

cylinder not

connected for

use shall not be stored in the

vicinity of this or any other

appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away

from the appliance and

immediately call your gas

supplier or your fire department.

Grill Installation Codes

The installation must conform with local codes or, in

the absence of local codes, with either the national fuel

gas code, ANSI Z 223.1/NFPA S4, Natural gas and

propane installation code, CSA B149.1, or propane

storage and handling code, B149.2, or the standard for

Recreational vehicles, ANSI A 119.2, and CSA Z240

RV series recreational vehicle code, as applicable.

LP gas grill models are designed for use with a

standard 20 lb. Liquid Propane Gas tank, not included

with grill. Never connect your gas grill to an LP gas

tank that exceeds this capacity.

2

!

• Have your LP gas tank filled by a reputable

propane gas dealer and visually inspected and re-

qualified at each filling.

• Do not store a spare LP gas tank under or

• Never fill the tank beyond 80 percent full . If this

information is not followed exactly a fire causing

death or serious injury may occur.

• Always keep LP gas tanks in an upright position.

• Do not store (or) or use gasoline or other

flammable vapors and liquids in the vicinity of this

gas grill.

• Do not subject the LP gas tank to excessive heat.

• Never store an LP gas tank indoors. If you store

your gas grill in the garage or other indoor

location, always disconnect the LP gas tank first

and store it safely outside.

• Place dust cap on cylinder valve outlet whenever

A tank of approximately 12 inches in diameter by 18-

1/2 inches high is the maximum size LP gas tank to

use. You must use an OPD gas tank which offers

an Overfill Prevention Device.

This safety feature prevents the tank from being

overfilled which can cause malfunction of the LP gas

tank, regulator and/or grill.

The LP gas tank must be constructed and marked in

accordance with specifications of the U.S. Dept. of

Transportation (DOT). In Canada, the LP gas tank

must meet the National Standard of Canada ,Can

CSA –B339 , Cylinders , spheres and Tubes for

Transportation of Dangerous Goods and

Commission .

1. The LP gas tank must have a shutoff valve,

terminating in an LP gas supply tank valve outlet,

that is compatible with a Type 1 tank connection

device. The LP gas tank must also have a safety

relief device that has a direct connection with the

vapor space of the tank.

2. Always keep LP gas tanks in an upright position.

The tank supply system must be arranged for vapor

withdraw.

3. The LP gas tank used must have a collar to

protect the tank valve.

Safety Precautions

the cylinder is not in use. Only install the type of

dust cap on the cylinder valve outlet that is

provided with the cylinder valve. Other types of

caps or plugs may result in leakage of propane.

• LP gas tanks must be stored outdoors in a well-

ventilated area and out of reach of children.

Disconnected LP gas tanks must not be stored in

a building, garage or any other enclosed area.

• When your gas grill is not in use the gas must be

turned off at the LP gas tank.

• The pressure regulator and hose assembly must

be inspected before each use of the grill. If there

is excessive abrasion or wear or if the hose is cut,

it must be replaced prior to the grill being used

again.

• Keep the gas regulator hose away from hot grill

surfaces and dripping grease. Avoid unnecessary

twisting of hose. Visually inspect the hose prior to

each use for cuts, cracks, excessive wear or

other damage. If the hose appears damaged do

not use the gas grill. Callfor assistance.

•Never light your gas grill with the lid closed or

before checking to ensure the burner tubes are

fully seated over the gas valve orifices.

•Never allow children to operate your grill.

Proper Placement and Clearance of Grill

Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area. Your gas grill

is to be used outdoors only, at least 24 inches from

the back and side of any combustible surface. Your

gas grill should not be used under overhead

combustible construction . Do not obstruct the flow of

ventilation air around the gas grill housing.

• Do not install this outdoor gas grill in or on

recreational vehicles or boats

• Keep outdoor gas grill area clear and free from

combustible materials, gasoline and other flammable

vapors and liquids

• Do not obstruct the flow of combustion and

ventilation air. Check for this each time prior to using

grill.

•Never connect an unregulated LP gas tank to your

gas grill. The gas regulator assembly supplied with

your gas grill is adjusted to have an outlet pressure

of 11” water column (W.C.) for connection to an LP

gas tank.

• Only use the regulator and the hose assembly

supplied with your gas grill. Replacement regulators

and hose assemblies must be those specified in this

manual.

3

WARNING

A strong gas smell, or the hissing sound of gas

indicates a serious problem with your gas grill or

the LP gas tank. Failure to immediately follow the

steps listed below could result in a fire or

explosion that could cause serious bodily injury,

death, or property damage.

• Shut off gas supply to the gas grill.

• Turn the control knobs to OFF position.

• Put out any flame with a proper fire extinguisher.

• Open Grill Lid.

• Get away from the LP gas tank.

• Do not try to fix the problem yourself.

• If odor continues or you have a fire you can not

extinguish, call your fire department. Do not call

near the LP gas tank because your telephone is

a form of electrical device and could create a

spark resulting in fire and/or explosion.

NOTE: The normal flow of gas through the

regulator and hose assembly can create a

humming noise. A low volume of noise is perfectly

normal and will not interfere with operation of the

grill. If humming noise is loud and excessive you

may need to purge air from the gas line or reset

the regulator excess gas flow device. This purging

procedure should be done every time a new LP

gas tank is connected to your grill. For help with

Visually check the burner flames prior to each use. The

flames should look like picture, if they do not, refer to the

Cleaning Burner Tubes and Burner Ports , see page 22 of

this manual.

!Burner Flame Check

WARNING

Pls ensure cleaning the flame tamer/cooking

grid/grease pan/tray after each use. Failure to

comply this could result in a fire or explosion that

could cause serious bodily injury, death, or property

damage.

!

CAUTION: Spiders and small insects occasionally

spin webs or make nests in the grill burner tubes

during transit and warehousing. These webs can lead

to gas flow obstruction which could result in a fire in

and around burner tubes. This type of fire is known as

“FLASH-BACK” and can cause serious damage to

your grill and create an unsafe operating condition for

the user.

Although an obstructed burner tube is not the only

cause of “FLASH-BACK”, it is the most common

cause.

To reduce the chance of “FLASH-BACK”, you must

clean the burner tubes before assembling your grill,

and at least once a month in late summer or early fall

when spiders are most active. Also perform this burner

tube cleaning procedure if your grill has not been used

for an extended period of time.

See Cleaning Burner Tubes and Burner Ports on page

# 22

this procedure refer to page 19, Item 4 of “If Grill

Still Fails To Light”, or call the Customer Service

Helpline

4

CAUTION: Beware of Flash-Back

The following table illustrates a breakdown of the hardware pack. It highlights what components are used in

the various stages of assembly.

Contents for Hardware Pack

A

5/32"x12mm 15 pcs

B

1/4"x15mm 17 pcs

C

2 pcs

D

1/4'' 4 pcs

5

Tools required for assembly

Philips Head Screwdriver (not included).

Note: The left and right sides of the grill are on your left and right as you face the front of the grill.

Philips Head Screwdriver

Model 77352 Parts Diagram

6

Model 77352 Parts List

seq.

NO.

appellation qty Material code seq.

NO.

appellation qty Material

code

1 Main Lid 1 D010015902 40 Side Panel, Right 1 D010012903

2 Temperature Gauge 1 A0212824 41 Battery Box 1 A0212663

3 Temperature Gauge Seat 1 A0212825 42 Spindle Below Door Panel 2 A0212557

4 Main Lid Screw 2 A0407131 43 Spacing Screw Below Door Panel 2 A02120079

5 Main Lid Handle 1 D010011245 44 Cart Bottom Panel Front

Cummerbund Strip

1 D010013610

6 Hood Buffer 4 A0201340 45 Triangle Bracket, Left 2 D010012745

7 Warming Rack 1 A02120163 46 Swivel Caster Fixing Plug 4 A0212805

8 Cooking Grid With Hole, A 3 A02120164 47 Swivel Caster 4 A0211004

9 Flame Tamer 6 D010012307 48 Gas-jar Fixing Line 1 A0212837

10 Clamp Spring 6 A0212873 49 Lighting Rod 1 A02121323

11 Main Burner 6 A0212926 50 Door Handle 2 D010012747

12 Main Burner Igniter Wire 6 D010015903 51 Front Door 2 D010013998

13 Back Panel, Top 1 D010015746 52 LED Lamp Seat-USB2.0 1 A02120032

14 Grease Box Bracket 1 A0212838 53 LED Lamp Switch 1 A0212627

15 Grease Box 1 D010012705 54 LED Lamp Circuit 1 D010015910

16 Grease Tray 1 D010021003 55 Main Control Panel 1 D010013625

17 Side Burner Lid Hinge Rod 1 A0212534 56 Main Control Panel Frame 1 D010013594

18 Side Burner Lid 1 D010007598 57 Gas Connector 1 A0212830

19 Side Burner Cooking Grid, Right 1 A0212248 58 Gas Connector Fixing Panel 1 D010012298

20 Side Burner, Right 1 A0212533 59 Main Burner Flex Gas Line 1 A0212829

21 Side Burner Tray 1 D011006420 60 Regulator, LP 1 A0212831

22 Side Burner Orifice Bracket 1 D019706920 61 Main Manifold 1 A02120158

For assembly questions, call:

1- 800-530-9133

To make sure you obtain the correct replacement

parts for your gas grill, please refer to the part

numbers on this page.

Important: Use only parts listed above. When ordering

parts, providing the following information:

1. Model #

2. Part Number (see PART# in chart)

3. Part Description

4. Quantity of parts needed

7

Important: Keep this Owner’s Manual for

convenient reference and for part replacement.

23 Side Burner Igniter, Right 1 A0212436 62 Main Gas Valve 6 A0212862

24 Side Burner Igniter Wire, Right 1 A0212890 63 Front Baffle 1 D010014626

25 Side Shelf, Right 1 D010014389 64 Control Panel Fixing Panel, Left 1 D010012050

26 Hook 1 D010018023 65 Control Panel Fixing Panel, Right 1 D010012051

27 Side Burner Orifice 1 A0212828 66 Side Shelf, Left 1 D010012770

28 Side Burner Flex Gas Line, 250 1 A020021 67 Firebox 1 D010013634

29 Side Burner Flex Gas Line, 480 1 A02120090 68 Back Panel, A 1 D010015754

30 Side Burner Gas Vavle, Right 1 A02120088 69 Pulsating adiabatic box 1 D010014628

31 Control Knob Base 7 D010015906 70 Firebox fixing panel

，

middle 1 D010013617

32 LED Lamp Panel 7 A02120213 71 Gas cylinder baffler-A 1 D010022390

33 Control Knob 7 A02120298 72 Gas cylinder bottom base 1 D010015798

34 Pulse Igniter Module 1 A02120161 73 Cooking Grid With Hole, B 1 A02120165

35 Side Panel,Left 1 D010012742 74 Gas cylinder baffler-B 1 D010022388

36 Door Magnet 2 A0201249 75 Gas cylinder baffler-C 1 D010022389

37 Cart Frame, Front 1 D010015794 76 Logo 1 A0212808

38 Back Panel, Bottom 1 D010015796 Manual 1 C042363

39 Bottom Panel 1 D010015792 Hardware Pack 1 D010015797

Assembly Instructions

Figure 1

Please insert Part No.47 into the bottom plate.

Figure 2

8

Half screw out the screws in the

bottom plate, then put Part No.35 and

Part No.40 onto the relevant screw

holes and screw tightly.

Figure 3

4 x

B

Install Part No.38 onto the relevant place

with four B screws.

Figure 4

9

Half screw out the screws in the bottom

and side plates, then put Part No.45 onto the relevant

screw holes and screw tightly.

Figure 5

4 x

A

Install Part No.37 onto the relevant place with

four A screws shown in Figure 5.

Attention: magnet downward.

10

Figure 6

1 x

A

Install Part No. 71 onto Part No.39 with A screws.

Figure 7.1

1 x

A

1 x

Figure 7.2

Install Part No. 71 ,No.74 onto Part

No.37 with A screws.

Install Part No. 74 onto Part No.38.

11

Figure 8

1 x

A

Install Part No. 75 onto Part

No.71 with A screws.

Figure 9

1 x

A

Install Part No. 75 onto Part

No.38 with A screws.

12

Figure 10

Figure 11

4 x

B

Screw the grill body and the

cart tightly with four B screws.

13

Figure 12.1 Figure 12.2

2 x B

2 x D

1.Half screw out the three big screws outside the grill body,

then put Part No.25 onto the relevant screw holes and screw tightly.

2.Screw Part No.25 tightly with B screw and D spacer inside the grill body.

Figure 13

1. Insert Part No.30, Part No.32 and Part No.33 as the figure shows.

2. Insert the wire as the figure shows.

2 x

Figure 14

14

Half screw out the screw in Part No.27,

then put it into the hole of Part No.22

and screw tightly.

Figure 15.1

2 x B

2 x D

1.Half screw out the three big screws on the grill body,

then put Part No.66 onto the relevant screw holes and screw tightly.

2.Screw Part No.66 tightly with B screw and D spacer inside the grill body.

Figure 15.2 Figure 15.3

Figure 16

15

1 x

A

Fixed Part No.58 onto the right plate with one A screw.

Figure 17

4 x

B

Install Part No. 72 onto Part

No.39 with B screws.

Figure 18.1

16

Figure 18.2 Figure 18.3

C

1.Install Part No. 50 onto Part No.51 with A screws. (Figure 18.1)

2.Put the C part into the relevant hole in the bottom plate. (Figure 18.2)

3.Put Part No.51 into the C part. (Figure 18.2)

4.Then put the door into by pressing the flexible axis upward.

4 x

A

Figure 19

2 x

A

1.Install Part No.14 onto Part No.16 with two A screws.

2.Put Part No.15 into Part No.14.

3.Put the grease tray into the grill body.

1

23

Figure 20

17

Put Part No. 7, Part No. 8 , Part No. 9 and Part No. 73 into the relevant place.

Connect Part No.54 to Part No.41.

3

21

Figure 21

18

Figure 22.1 Figure 22.2

Install Part No. 26 onto the side plate.

1 x

B

Install Part No. 48 onto Part No.72.

assemble it on the side or fro

nt of the left/right side table

Connecting LP Gas Tank to LP Grill

1. Place foot ring of 20 lb tank into the hole in bottom

panel. Make sure the tank valve is in OFF

position.(Fig.24).

2. Check the tank valve to ensure it has proper

external mating threads to fit the hose and regulator

assembly provided.

3. Make sure all burner valves are in OFF position.

4. Inspect the valve connection port and regulator

assembly. Look for damage or debris. Remove any

debris. Inspect hose for damage. Never use

damaged or plugged equipment.

5. When connecting regulator and hose assembly to

tank valve hand tighten quick coupling nut clockwise

to a full stop (Fig.23) Do not use a wrench to tighten

because it could damage the quick coupling nut and

result in a hazardous condition.

6. Open tank valve fully (counterclockwise). Use a

soapy water solution to check all connections for

leaks before attempting to light your grill. If a leak is

found, turn tank valve off and do not use your grill

until the leak is repaired.

CAUTION: When the appliance is not in use, gas

must be turned off at the supply tank.

Regulator Connection

Figure 23

Congratulations

Your gas grill is now ready for use. Before the

first use and at the beginning of each season

(and whenever the LP gas tank has been

changed):

1. Read all safety, lighting and operating

instructions.

2. Check gas valve orifices, burner tubes and

burner ports for any obstructions.

3. Perform gas leak check according to

instructions found on next page of the manual.

19

Figure 24

7. To light burners, push and turn burner knob (s)

to IGNITE/HI. At the same time, press and hold

electronic ignition button for 3 to 5 seconds to light

burner. Adjust knob (s) to desired setting.

8. If the burner does not light after 5 seconds, turn

knob to OFF. Turn gas OFF at LP tank and wait 5

minutes for gas to clear. Then turn gas ON at tank

and repeat step 6.

9. If burner still does not light, see Match Lighting

section and If Grill Still Fails to Light section on

following page.

1. Make a 50/50 (soap/water) mild soap solution.

2. Turn the control knobs to full OFF position; then

turn gas ON at supply tank.

3. Apply the soap solution with a clean brush to all

gas connections. See below. If growing bubbles

appear in the solution the connections are not

properly sealed. Check each fitting and tighten or

repair as necessary.

4. If you have a gas connection leak you cannot

repair, turn gas OFF at supply tank, disconnect

fuel line from your grill and call your gas supplier

for repair assistance.

5. Also apply soapy solution to the tank seams. See

below. If growing bubbles appear, shut tank OFF

and do not use or move it! Contact an LP gas

USING THE SIDE BURNER

Inspect the gas supply hose prior to turning the gas

“ON”. If there is evidence of cuts, wear or abrasion,

it must be replaced prior to use. Do not use the

side burner if the odor of gas is present.

WARNING: Always keep your face and body as

far away from the burner as possible when

lighting.

Gas Connection Leak Check

Checking for LP gas leaks

Never test for leaks with a flame. Prior to first use, at

the beginning of each season, or every time your LP

gas tank is changed, you must check for gas leaks.

LIGHTING INSTRUCTIONS FOR SIDE BURNER

1. Open side burner lid fully.

2. Push and turn side burner knob to IGNITE/HI

position. At the same time, press and hold

electronic ignition button for 3 to 5 seconds to

light burner.

3. If the side burner does not light after 5 seconds,

turn knob to OFF. Turn gas OFF at LP tank and

wait 5 minutes for gas to clear. Then turn gas

ON at tank and repeat step 2.

4. If burner still does not light, see Match Lighting

section and If Grill Still Fails to Light section on

following page.

Grill Lighting Instructions for Main Burners

1. Do not smoke while lighting grill or checking gas

supply connections.

2. Be sure that LP gas tank is sufficiently full.

3. Be sure all gas connections are securely tightened.

4. Turn on gas supply

5. Open the grill main lid and side burner lid.

6. Push and turn any main burner knob to IGNITE/HI

position, at the same time, press and hold

electronic ignition button for 3 to 5 seconds to light burner.

supplier or your fire department for assistance.

WARNING

Failure to open grill lid during the lighting

procedure could result in a fire or explosion

that could cause serious bodily injury, death,

or property damage.

!

20

Gas Tank Leak Check

Grill Lighting Instruction

La page est en cours de chargement...

Monument 77252 Le manuel du propriétaire

Monument 77252 Le manuel du propriétaire

dans d''autres langues