iHealth View BP7S Wireless Blood Pressure Wrist Monitor Manuel utilisateur

Marque: iHealth

Modèle: View BP7S Wireless Blood Pressure Wrist Monitor

Catégorie: Unités de pression artérielle

Taper: Manuel utilisateur

Wireless Blood Pressure

Wrist Monitor (BP7S)

Tensiomètre de poignet

sans fil (BP7S)

USER GUIDE

MODE D’EMPLOI

Wireless Blood Pressure Wrist Monitor (BP7S)

USER GUIDE

Table of Contents

INTRODUCTION

PACKAGE CONTENTS

INTENDED USE

CONTRAINDICATION

PARTS AND DISPLAY INDICATORS

SET UP REQUIREMENTS

SET UP PROCEDURES

MEASUREMENT PROCEDURES

SYNC TIME AND RESULTS VIA BLUETOOTH

SPECIFICATIONS

GENERAL SAFETY AND PRECAUTIONS

BATTERY HANDLING AND USAGE

TROUBLESHOOTING

CARE AND MAINTENANCE

WARRANTY INFORMATION

EXPLANATION OF SYMBOLS

CONTACT AND CUSTOMER SERVICE

IMPORTANT INFORMATION REQUIRED BY THE FCC

OTHER STANDARDS AND COMPLIANCES

INTRODUCTION

Thank you for selecting the iHealth View Wireless Blood Pressure Wrist Monitor. The iHealth Wireless Blood

Pressure Wrist Monitor is a fully automatic wrist cuff blood pressure monitor that uses the oscillometric principle

to measure your blood pressure and pulse rate. The monitor works with your mobile devices to track and share

vital blood pressure data.

PACKAGE CONTENTS

• 1 iHealth View Wireless Blood Pressure Wrist Monitor

• 1 User Guide

• 1 Quick Start Guide

• 1 Charging Cable

• 1 Travel Case

INTENDED USE

The iHealth View Wireless Blood Pressure Wrist Monitor (Electronic Sphygmomanometer) is intended for use

in a professional setting or at home and is a non-invasive blood pressure measurement system. It

is designed to measure the systolic and diastolic blood pressures and pulse rate of an adult

individual by using a technique in which an inflatable cuff is wrapped around the wrist. The

measurement range of the standard cuff circumference is 5.3” to 8.7”(13.5cm-22cm).

Note: Consult your physician for proper interpretation of blood pressure results.

CONTRAINDICATION

It is not recommended for people with serious arrhythmia to use this Wireless Blood Pressure Monitor.

PARTS AND DISPLAY INDICATORS

START/STOP button

Systolic

Diastolic

Pulse

Battery

Sync indicator

Charging indicator

Position detect indicator

Bluetooth indicator

Pulse indicator

Cuff

Adapter Jack

Result indicator

SET UP REQUIREMENTS

Compatible with iPhone 4s+, iPod touch 5, iPad 3+, iPad mini+, iPad Air+ and select Android phones. Requires

iOS version 7.0+ and Android version 4.0+. For a complete list of compatible devices, visit our support page at

www.ihealthlabs.com/support.

SET UP PROCEDURES

Download the Free iHealth MyVitals App

Prior to first use, download and install “iHealth MyVitals” from the App Store or Google Play Store. Follow the

on-screen instructions to register and set up your personal account.

Access the iHealth Cloud Account

Your iHealth account also gives you access to the free and secure iHealth cloud service. Go to

www.ihealthlabs.com and sign in with the same account.

Charge Battery before First Use

Connect the monitor to a USB port using the charging cable provided until the charging indicator light

green and indicator steady.

BODY POSTURE DURING MEASUREMENT

Blood pressure can be affected by the position of the cuff and your physiologic condition. It is very important

that the cuff is positioned at your heart level during blood pressure measurements.

1. Sit comfortably with your feet flat on the floor without crossing your legs. Stay still during measurement. Do

not move your wrist, body, or the monitor.

2. Place your hand palm-side up in front of you and leave 1-2cm between the monitor and the bottom of your

palm. If the monitor is correctly placed, iHealth logo will be facing upright.

3. The center of the cuff should be at your heart level.

4. It is advised to place the monitor’s travel case under your arm for support and to keep your arm at optimal

height for measurement.

SET UP REQUIREMENTS

Compatible with iPhone 4s+, iPod touch 5, iPad 3+, iPad mini+, iPad Air+ and select Android phones. Requires

iOS version 7.0+ and Android version 4.0+. For a complete list of compatible devices, visit our support page at

www.ihealthlabs.com/support.

SET UP PROCEDURES

Download the Free iHealth MyVitals App

Prior to first use, download and install “iHealth MyVitals” from the App Store or Google Play Store. Follow the

on-screen instructions to register and set up your personal account.

Access the iHealth Cloud Account

Your iHealth account also gives you access to the free and secure iHealth cloud service. Go to

www.ihealthlabs.com and sign in with the same account.

Charge Battery before First Use

Connect the monitor to a USB port using the charging cable provided until the charging indicator light

green and indicator steady.

BODY POSTURE DURING MEASUREMENT

Blood pressure can be affected by the position of the cuff and your physiologic condition. It is very important

that the cuff is positioned at your heart level during blood pressure measurements.

1. Sit comfortably with your feet flat on the floor without crossing your legs. Stay still during measurement. Do

not move your wrist, body, or the monitor.

2. Place your hand palm-side up in front of you and leave 1-2cm between the monitor and the bottom of your

palm. If the monitor is correctly placed, iHealth logo will be facing upright.

1/2" (1-2cm)

iHealth

START

3. The center of the cuff should be at your heart level.

4. It is advised to place the monitor’s travel case under your arm for support and to keep your arm at optimal

height for measurement.

TAKING YOUR BLOOD PRESSURE READING

1. Apply the cuff or press the START/STOP button, the monitor will activate and begin to detect your wrist position.

2. Adjust the height of your wrist, the monitor will detect your wrist position and the measurement will start

ONLY when the correct position is detected. When the position is correct, press "START/STOP" button again

to start measurement.

3. Then the cuff will be slowly inflated. The blood pressure and pulse will be measured during inflation. Inflation

will stop as soon as the blood pressure and pulse rate have been calculated and displayed on the screen. The

result will be automatically stored in the memory, and all results will be uploaded to the App automatically

upon the next successful Bluetooth connection.

SYNC TIME AND RESULTS VIA BLUETOOTH

Connect to iOS Device via Bluetooth

1. Launch the iHealth MyVitals App from your iOS device.

2. Enable Bluetooth on your iOS device: Slide gently upward the iPhone screen from to open

the Control Center, and click on the

3. Press "START/STOP" button for 3 seconds until Bluetooth indicator begins flashing -- when a successful

connection has been established, the Bluetooth indicator light will stop flashing.

4. When sync is processing, the sync indicator flash and , when sync is finished, the sync indicator

lights up

Connect to Android Device via Bluetooth

• Press the START/STOP button for 2 seconds, the Bluetooth indicator will begin flashing.

• Enable the Bluetooth on your Android Device.

• When using the monitor for the first time, you should pair the monitor to the Android device. Go into your

device’s setting to pair it with your Android device. Check the Bluetooth menu for the model name of your

monitor (BP7SXXX) to appear, and then select it to pair. This may take up to 30 seconds and your monitor’s

Bluetooth indicator will light up when a connection has been established.

• Launch the “iHealth MyVitals” app to sync with your monitor.

• When sync is processing, the sync indicator flash and , when sync is finished, the sync indicator

lights up

• Please repeat these steps when you switch to another Android device with the monitor.

Remember to:

1. Make sure your wrist size is within cuff circumference; see the range in “SPECIFICATIONS”

2. Measure on the same wrist each time.

3. Stay still and calm for one to one and half minutes before taking a blood pressure measurement. Prolonged

over-inflation of the bladder may cause bruises of your wrist.

4. Keep the cuff clean. Cleaning the cuff after every 200 times of usage is recommended. If the cuff becomes

dirty, clean it with a moistened cloth. Do not rinse the monitor or cuff with running water.

5. Press the “START/STOP” button at any time to interrupt a measurement.

Note: Physical activity, eating, drinking, smoking, excitement, stress, and many other factors influence blood

pressure results.

SPECIFICATIONS

1. Product name: iHealth View Wireless Blood Pressure Wrist Monitor

2. Model: BP7S

3. Classification: Internally powered; Type BF applied part; IP22, No AP or APG; Continuous operation

4. Machine size: approx. 2.8"×2.9"×0.7" (72mm×74mm×17.6mm)

5. Cuff circumference: 5.3"- 8.7" (13.5cm-22cm)

6. Weight: approx. 4.2oz(120g)(including cuff)

7. Power: DC:5.0V 1.0A, Battery: 1*3.7V Li-ion 400mAh

8. Measurement range:

Cuff pressure: 0-300 mmHg

Systolic: 60-260 mmHg

Diastolic: 40-199 mmHg

Pulse rate: 40-180 beats/minute

9. Accuracy:

Pressure: ±3 mmHg

Pulse rate: ±5%

10. Environmental temperature for operation: 10°C-40°C(50°F -104°F)

11. Environmental humidity for operation: ≤85%RH

12. Environmental temperature for storage and transport:-20°C-55°C(-4°F-131°F)

13. Environmental humidity for storage and transport: ≤85%RH

14. Environmental pressure: 80kPa-105kPa

15. Battery life: more than 80 measurements on a full charge

16. The blood pressure measurement system includes accessories: pump, valve, cuff, and sensor.

Note: These specifications are subject to change without notice.

GENERAL SAFETY AND PRECAUTIONS

1. Read all of the information in the User Guide and other provided instructions before operating the unit.

2. Consult your physician for any of the following situations:

a) The application of the cuff over a wound or inflamed area.

b) The application of the cuff on any limb with intravascular access or therapy, or an arteriovenous (A-V) shunt.

c) The application of the cuff on the arm on the side of a mastectomy.

d) Simultaneous use with other medical monitoring equipment on the same limb.

e) The blood circulation of the user needs to be checked.

3. Do not use this product in a moving vehicle as this may result in inaccurate measurements.

4. Blood pressure measurements determined by this product are equivalent to those obtained by professional

healthcare practitioners using the cuff/stethoscope auscultation method within the limits prescribed by the

American National Standard, Electronic or Automated Sphygmomanometer. This device is also clinically

validated according to the 2010 Protocol of the European Society of Hypertension (ESH 2010).

5. If an Irregular Heartbeat (IHB) is detected during the measurement procedure, the IHB symbol will be

displayed in the “iHealth MyVitals” APP. Under this condition, the Wireless Blood Pressure Wrist Monitor can

keep functioning, but the results may be inaccurate. Please consult your physician for accurate assessment.

The IHB symbol will be displayed under 2 conditions:

1) The coefficient of variation (CV) of pulse period >25%.

2) The difference of adjacent pulse period is ≥0.14s and more than 53 percent of the total number of pulses

readings falls within this definition.

6. Please do not use any cuff other than that supplied by the manufacturer as this may result in inaccurate

measurements.

7. For information regarding potential electromagnetic or other interference between the blood pressure monitor

and other devices together with advice regarding avoidance of such interference, please see ELECTROMAG-

NETIC COMPATIBILITY INFORMATION. It is suggested that the blood pressure monitor should be operated at

least 10 meters away from electric or wireless devices (e.g. routers, microwave oven, etc.)

8. If the blood pressure measurement (systolic or diastolic) is outside the rated range specified in part

SPECIFICATIONS, the monitor will immediately display a technical alarm on the screen. In this case, repeat

the measurement ensuring that the proper measurement procedures are followed and/or consult with your

medical professional. The technical alarm is preset in the factory and cannot be adjusted or inactivated. This

technical alarm is assigned as low priority according to IEC 60601-1-8. The technical alarm does not need to

be reset.

9. This device requires a medical AC adapter with an output of DC 5.0V that complies with IEC 60601-1/UL

60601-1 and IEC 60601-1-2/EN 60601-1-2 such as ASP5-05010002JU (input: 100-240V, 50/60Hz, 200mA;

output: DC 5V, 1.0A). Please note that the monitor jack size is USB mini B. The USB jack should be used for

charging only.

This Monitor is designed for adults and should never be used on infants, young children, pregnant or

pre-eclamptic patients. Consult your physician before use on children.

This product might not meet its performance specifications if stored or used outside the specified

temperature and humidity ranges.

Please do not share the cuff with any infectious person to avoid cross-infection.

BATTERY HANDLING AND USAGE

• The battery charge will be displayed on the LED screen when the monitor is active. And when the monitor is

connected to the “iHealth MyVitals” APP, the battery charge will be displayed in the APP. If the power is less

than 25%, please charge the battery. The monitor will not work until the battery has enough power.

• When the monitor needs charging, please connect the monitor to a power source. The monitor can work

normally while charging.

• You should charge the battery when the battery is less than 25% charged. Overcharging the battery may

reduce its lifetime.

• When in charging mode, the charging status will be displayed on the LED screen. See the table below for details.

Status Indicator

Do not change the battery. If the battery can no longer be charged, please contact Customer Service.

Overcharging the battery may reduce its lifetime.

Lithium battery replacement by inadequately trained personnel could result in a hazard such as a fire or

explosion.

Do not plug or unplug the power cord into the electrical outlet with wet hands. If the AC adapter is abnormal,

please change the adapter.

Do not pull out the adapter when you are using the monitor.

Do not use any other type of AC adapter as it may harm the monitor.

The monitor, cable, battery and cuff must be disposed of according to local regulations at the end of their usage.

Note: Battery life and charge cycles vary by use and settings.

PROBLEM POSSIBLE CAUSE SOLUTION

Battery do not have enough power Charge the batteryLow Battery

Pressure system is unstable before measurement

Fail to detect systolic pressure

Fail to detect diastolic pressure

Pneumatic system blocked or cuff is too

tight during inflation

Pneumatic system leakage or cuff is too

loose during inflation

TROUBLESHOOTING

Retest, make sure not to move

your arm or the monitor

Apply the cuff correctly and try again

LED display reads“Er0”

LED display reads“Er1”

LED display reads“Er2”

LED display reads“Er3”

LED display reads“Er4”

LED display reads“Er5”

LED display reads“Er6”

LED display reads“Er7”

LED display reads“Er8”

LED display reads“ErA”

Cuff pressure above 300mmHg

More than 160 seconds with cuff pressure above

15 mmHg

memory accessing error

Device parameter checking error

Pressure sensor parameter error

Measure again after five minutes.

If the monitor is still abnormal,

please contact the local distributor

or the factory.

LED display reads “ Er ” Bluetooth communicate error

Connect the mobile device correctly

and try again, If the monitor is still

abnormal, please contact the local

distributor or the factory.

LED display reads

an abnormal

result

The cuff position was not correct or it was not

properly tightened

Body posture was not correct during testing

Speaking, moving arm or body, being angry,

excited or nervous during test

Review the cuff application instructions

and retest

Review body posture instructions and

retest

Retest when calm; avoid speaking or

movement during the test

Bluetooth connection

unstable

No response when you

press button

Bluetooth connection unsuccessful, monitor is

abnormal, or strong electromagnetic interference

is present

Incorrect operation or strong electromagnetic

interference

Reset iOS/Android device. Reset monitor by

pressing the START/STOP button and holding

for about 10 seconds. Make sure the monitor

and iOS/Android device are away from other

electrical equipment. Please see GENERAL

SAFETY AND PRECAUTIONS

Press the START/STOP button and hold

for about 10 seconds to reset the device.

CARE AND MAINTENANCE

1. If this monitor is stored near freezing temperatures, allow it to return to room temperature before use.

2. If the monitor is not used for a long time, please be sure to fully charge it every month.

3. No monitor component needs to be maintained by the user. The circuit diagrams, component part lists,

descriptions, calibration instructions, or other information which will assist the user’s appropriately qualified

technical personnel to repair those parts of the equipment which are designated for repair can be supplied by

the iHealth technical department.

4. Clean the monitor with a dry, soft cloth or a moistened and well wrung soft cloth using water, diluted

disinfectant alcohol, or diluted detergent.

5. The monitor can maintain the safety and performance characteristics for a minimum of 10,000 measurements

or three years of usage, and the cuff integrity is maintained after 1,000 open close cycles.

6. The battery can maintain the performance characteristics for a minimum of 300 charge cycles.

7. It is recommended that if the cuff is used in a hospital or a clinic, it be disinfected twice a week. Wipe the

inner side (the side that contacts skin) of the cuff with a soft cloth lightly moistened with Ethyl alcohol

(75-90%). Then air dry the cuff.

Do not drop this monitor or subject it to strong impact.

Avoid high temperature and direct sunlight. Do not immerse the monitor in water as this will result in damage

to the monitor.

Do not attempt to disassemble this monitor.

Battery replacement should only be performed by a qualified iHealth technician. To do otherwise will void

your warranty and possibly damage your unit.

Cuff replacement should only be performed by a qualified iHealth technician. To do otherwise

will possibly damage your unit.

8. It is recommended that product performance be checked every 2 years or after each repair. Please contact

the iHealth Customer Service Center to do so.

Symbol for "WARNING" Symbol for "MANUFACTURER"

Symbol for "EUROPEAN REPRESENTATIVE"

Symbol for "SERIAL NUMBER"

Symbol for "KEEP DRY"

Symbol for "ENVIRONMENT PROTECTION – Waste electrical products should not be

disposed of with household waste. Please recycle where facilities exist. Check with your

local authority or retailer for recycling advice".

Symbol for "THE OPERATION GUIDE MUST BE READ"

The sign background color: blue The sign graphical symbol: white

Symbol for "TYPE BF APPLIED PARTS" (cuff only)

WARRANTY INFORMATION

The iHealth View Wireless Blood Pressure Wrist Monitor is warranted to be free from defects in materials and

workmanship within one year from the date of purchase when used in accordance with the provided instruc-

tions. The warranty extends only to the end user. We will, at our option, repair or replace without charge the

iHealth View Wireless Blood Pressure Wrist Monitor covered by the warranty. Repair or replacement is our only

responsibility and your only remedy under the warranty.

EXPLANATION OF SYMBOLS

Symbol for "COMPILES WITH MDD93/42/EEC REQUIREMENTS"

iHealth is a trademark of iHealth Lab Inc.

iPad, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

CONTACT AND CUSTOMER SERVICE

Manufactured for iHealth Lab Inc.

719N . Shoreline Blvd.,Mountain View, CA 94043, USA

Tel:+1-855-816-7705 www.ihealthlabs.com

iHealthlabs Europe

3 Rue Tronchet,75008,Paris,France

[email protected] www.ihealthlabs.eu

ANDON HEALTH CO., LTD.

No. 3 Jinping Street, YaAn Road, Nankai District, Tianjin 300190, China.

Tel: 86-22-60526161

IMPORTANT INFORMATION REQUIRED BY THE FCC

This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by iHealth Lab Inc. would void the user’s authority to operate

the product.

Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This product generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

product does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

OTHER STANDARDS AND COMPLIANCES

The Wireless Blood Pressure Wrist Monitor corresponds to the following standards:

IEC 60601-1:2005 corr.1(2006)+corr.2(2007)/EN 60601-12006/A11: 2011(Medical electrical equipment – Part 1:

General requirements for safety)

IEC 60601-1-2:2007/EN 60601-1-2:2007 /AC:2010 (Medical electrical equipment – Part 1: General requirements

for safety; Collateral Standard-Electromagnetic compatibility - Requirements and tests);

EN 1060-1: 1995 + A1: 2002 + A2: 2009 (Non-invasive sphygmomanometers - Part 1: General requirements);

EN 1060-3: 1997 + A1: 2005 + A2: 2009 (Non-invasive sphygmomanometers - Part 3: Supplementary require-

ments for electro-mechanical blood pressure measuring systems);

IEC 80601-2-30 Edition 1.1 2013-07 (Medical electrical equipment –Part 2-30: Particular requirements for the

basic safety and essential performance of automated non-invasive sphygmomanometers).

ISO 81060-2 Second Edition 2013-05-01, Non-Invasive Sphygmomanometers - Part 2: Clinical Validation Of

Automated Measurement Type.

following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

This product complies with Industry Canada. IC: RSS-210

IC NOTICE

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

This product is approved in accordance to R&TTE directive transmitter.

Tensiomètre de poignet sans fil (BP7S)

MODE D’EMPLOI

Table des matières

PRÉSENTATION

CONTENU DE L’EMBALLAGE

OBJET DU DISPOSITIF

CONTRE-INDICATION

ÉLÉMENTS FOURNIS ET INDICATIONS QUI S’AFFICHENT

EXIGENCES DE CONFIGURATION

PROCÉDURES DE CONFIGURATION

POSTURE CORPORELLE PENDANT LA MESURE

MESURE DE VOTRE TENSION ARTÉRIELLE

DÉLAI DE SYNCHRONISATION ET RÉSULTATS À TRAVERS BLUETOOTH

SPÉCIFICATIONS

PRÉCAUTIONS GÉNÉRALES DE SÉCURITÉ

MANIPULATION ET UTILISATION DE LA BATTERIE

DÉPANNAGE

SOINS ET ENTRETIEN

INFORMATIONS SUR LA GARANTIE

EXPLICATION DES SYMBOLES

CONTACT ET SERVICE CLIENTÈLE

INFORMATIONS IMPORTANTES EXIGÉES PAR LA FCC (COMMISSION FÉDÉRALE DES COMMUNICATIONS DES ÉTATS-UNIS)

AUTRES NORMES ET CONFORMITÉS

PRÉSENTATION

Merci d’avoir choisi le tensiomètre de poignet sans fil iHealth View. Ce tensiomètre iHealth sans fil, entièrement

automatique, est un manchon de poignet qui utilise le principe oscillométrique pour mesurer votre tension et

votre cadence de pouls. Il fonctionne avec vos dispositifs mobiles pour suivre et partager vos données de

tension artérielle.

CONTENU DE L’EMBALLAGE

• 1 tensiomètre de poignet sans fil iHealth

• 1 mode d’emploi

• 1 guide de démarrage rapide

• 1 câble de chargement

• 1 trousse de voyage

OBJET DU DISPOSITIF

Le tensiomètre de poignet sans fil iHealth View (sphygmomanomètre électronique) est conçu pour être utilisé

dans un environnement professionnel ou à la maison. Il mesure la tension artérielle de manière non invasive. Il

est conçu pour mesurer les tensions systolique et diastolique et la cadence de pouls d’un adulte à l’aide d’un

manchon gonflable entourant le poignet. La plage de circonférences du manchon standard est de 13,5 à 22 cm

(5,3 à 8,7 in).

Remarque : Consultez votre médecin au sujet de l’interprétation correcte des valeurs de tension artérielle.

CONTRE-INDICATION

L’utilisation de ce tensiomètre sans fil est déconseillée aux personnes souffrant d’arythmies importantes.

ÉLÉMENTS FOURNIS ET INDICATIONS QUI S’AFFICHENT

Bouton MARCHE/ARRÊT

Brassard

Prise adaptateur

secteur

Affichage des résultats

Voyant Bluetooth

Systolique

Diasytolique

Voyant pouls

Voyant de charge

Voyant de synchronisation

Indicateur de détection

de posture

Pouls

Batterie

La page est en cours de chargement...

iHealth View BP7S Wireless Blood Pressure Wrist Monitor Manuel utilisateur

Marque: iHealth

Modèle: View BP7S Wireless Blood Pressure Wrist Monitor

Catégorie: Unités de pression artérielle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: iHealth View BP7S Wireless Blood Pressure Wrist Monitor User manual