Husqvarna ST 424 Series Snow Thrower Manuel utilisateur

Marque: Husqvarna

Modèle: ST 424 Series Snow Thrower

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

ST 424, ST 427, ST 430, ST 424T, ST

427T, ST 430T

EN Operator's manual 2-31

ES-MX Manual de usuario 32-65

FR-CA Manuel d’utilisation 66-99

Contents

Introduction............................................................... 2

Safety........................................................................6

Assembly.................................................................. 9

Operation................................................................ 13

Maintenance........................................................... 17

Troubleshooting...................................................... 27

Transportation, storage and disposal......................30

Technical data.........................................................31

Appendix ..............................................................100

Introduction

USA requirements

WARNING: Engine exhaust, some

of its constituents, and certain vehicle

components contain or emit chemicals

known to the State of California to

cause cancer and birth defects or other

reproductive harm.

WARNING: Engine exhaust and

certain vehicle components contain

or emit chemicals considered to

cause cancer, birth defects, or

other reproductive system damage.

The engine exhaust contains carbon

monoxide, which is an odorless,

colorless, poisonous gas. Do not use the

machine in enclosed spaces.

2876 - 017 -

Product overview

22 2

1. Fuel tank cap

2. Oil fill/dipstick

3. Battery cover

4. Discharge chute lever

5. Auger engagement

6. Drive speed lever

7. Control panel

8. Remote control lever

9. Drive engagement

10. Steering triggers

11. Handle knobs

12. Muffler

13. Wheel (for ST 424/427/430 only)

14. Continuous track (for ST 424T/427T/430T only)

15. Auger bucket

16. Skid plate

17. Augers

18. Tool for cleaning

19. Discharge chute

20. Discharge chute deflector

21. LED light

22. Oil drain

23. Starter rope handle

24. Hook cover

876 - 017 - 3

Product overview

1 4

1. Adjustment lever for the auger bucket

2. ON/OFF switch for the heated grip

3. Hour meter and oil change reminder

4. Throttle

5. Discharge chute lever

6. Release lever

7. Ignition slot

8. Auger engagement

9. Drive speed lever

10. Symbols label

11. Remote control lever for the discharge chute

deflector

12. Drive engagement

Product description

The product is a snow thrower that is used to

remove snow from the ground.

Intended use

This product can be used to remove snow from

fields, roads, walkways and driveways. Do not use

it on slopes that are greater than 20°. Do not use the

product in areas where there is much debris, dirt and

protruding stones.

Symbols on the product

Note: If the decals on the product are damaged,

contact the distributor to replace them.

Warning.

Read the operator's manual.

Engine on.

Start the engine.

Engine off.

4876 - 017 -

Boost.

Fast.

Slow.

Oil change reminder.

Heated handles.

Remove key before maintenance.

Remove spark plug cable before

maintenance.

Hot surface.

Risk of fire.

Beware of thrown objects.

Keep distance to bystanders.

Do not breathe in exhaust fumes.

Move slowly rearward.

Risk of falling.

No operation on slopes more than 20

degrees.

European machinery directive for

safety.

Steer left.

Steer right.

Blower on.

Traction drive on.

Ear protection recommended.

Wear protection gloves.

876 - 017 - 5

Change auger bucket

height.

Rotate left/rotate right.

Forward/reverse.

Up/down.

Product liability

As referred to in the product liability laws, we are not

liable for damages that our product causes if:

• the product is incorrectly repaired.

• the product is repaired with parts that are not

from the manufacturer or not approved by the

manufacturer.

• the product has an accessory that is not

from the manufacturer or not approved by the

manufacturer.

• the product is not repaired at an approved

service center or by an approved authority.

Safety

Safety definitions

The definitions below give the level of severity for

each signal word.

WARNING: Injury to persons.

CAUTION: Damage to the product.

Note: This information makes the product easier

to use.

General safety instructions

• Use the product correctly. Injury or death is a

possible result of incorrect use. Only use the

product for the tasks found in this manual. Do

not use the product for other tasks.

• Obey the instructions in this manual. Obey the

safety symbols and the safety instructions. If the

operator does not obey the instructions and the

symbols, injury, damage or death is a possible

result.

• Do not discard this manual. Use the instructions

to assemble, to operate and to keep your product

in good condition. Use the instructions for correct

installation of attachments and accessories. Only

use approved attachments and accessories.

• Do not use a damaged product. Obey the

maintenance schedule. Only do the maintenance

work that you find an instruction about in this

manual. An approved service center must do all

other maintenance work.

• This manual cannot include all situations that

can occur when you use the product. Be careful

and use your common sense. Do not operate

the product or do maintenance to the product if

you are not sure about of the situation. Speak to

a product expert, your dealer, service agent or

approved service center for information.

• Disconnect the spark plug cable before you

assemble the product, put the product into

storage or do maintenance.

• Do not use the product if it is changed from its

initial specification. Do not change a part of the

product without approval from the manufacturer.

Only use parts that are approved by the

manufacturer. Injury or death is a possible result

of incorrect maintenance.

• Do not breathe in the fumes from the engine.

Long term inhalation of the engine's exhaust

fumes is a health risk.

• Do not start the product indoors or near

flammable material. The exhaust fumes are hot

and can contain a spark which can start a fire.

Not sufficient airflow can cause injury or death

because of asphyxiation or carbon monoxide.

6876 - 017 -

• When you use this product the engine makes an

electromagnetic field. The electromagnetic field

can cause damage to medical implants. Speak to

your physician and medical implant manufacturer

before you operate the product.

• Do not let a child operate the product. Do not let

a person, without knowledge of the instructions

operate the product.

• Make sure that you always monitor a person,

with decreased physical capacity or mental

capacity, that uses the product. A responsible

adult must be there at all times.

• Lock the product in an area that children and

unapproved persons cannot access.

• The product can eject objects and cause injuries.

Obey the safety instructions to decrease the risk

of injury or death.

• Do not go away from the product when the

engine is on.

• The operator of the product is responsible if an

accident occurs.

• Before and while you walk rearward, look behind

and down for small children, animals or other

risks that can cause you to fall.

• Make sure that parts are not damaged before

you use the product.

• Make sure that you are at a minimum 15 m (50

ft) away from other persons or animals before

you use the product. Make sure that a person

in adjacent area knows that you will use the

product.

• Refer to national or local laws. They can prevent

or decrease the operation of the product in some

conditions.

Safety instructions for operation

• Do not put hands or feet near or under rotating

parts. Keep clear of the discharge opening at all

times.

• Exercise extreme caution when operating on or

crossing gravel drives, walks, or roads. Stay alert

for hidden hazards or traffic.

• After striking a foreign object, stop the engine

(motor), remove the wire from the spark

plug, disconnect the cord on electric motors,

thoroughly inspect the product for any damage,

and repair the damage before restarting and

operating the product.

• If the product starts to vibrate abnormally, stop

the engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

• Stop the engine (motor) whenever you leave the

operating position, before unclogging the auger

housing or chute deflector, and when making any

repairs, adjustments or inspections.

• When cleaning, repairing or inspecting the

product, stop the engine and make certain the

augers and all moving parts have stopped.

Disconnect the spark plug wire and keep the wire

away from the plug to prevent someone from

accidentally starting the engine.

• Do not run the engine indoors, except when

starting the engine and for transporting the

product in or out of the building. Open the

outside doors; exhaust fumes are dangerous.

• Exercise extreme caution when operating on

slopes.

• Never operate the product without proper guards,

and other safety protective devices in place and

working.

• Never direct the chute deflector toward people or

areas where property damage can occur. Keep

children and others away.

• Do not overload the product capacity by

attempting to clear snow at too fast a rate.

• Never operate the product at high transport

speeds on slippery surfaces. Look behind and

use care when operating in reverse.

• Disengage power to the augers when the product

is transported or not in use.

• Use only attachments and accessories approved

by the manufacturer of the product (such as

wheel weights, counterweights, or cabs).

• Never operate the product without good visibility

or light. Always be sure of your footing, and keep

a firm hold on the handles. Walk; never run.

• Never touch a hot engine or muffler.

Work area safety

• Thoroughly inspect the area where the

equipment is to be used and remove all

doormats, sleds, boards, wires, and other foreign

objects.

• Disengage all clutches and shift into neutral

before starting the engine (motor).

• Do not operate the product without wearing

adequate winter garments. Avoid loose fitting

clothing that can get caught in moving parts.

Wear footwear that will improve footing on

slippery surfaces.

• Handle fuel with care; it is highly flammable.

• Use an approved fuel container.

• Never add fuel to a running engine or hot

engine.

• Fill fuel tank outdoors with extreme care.

Never fill fuel tank indoors.

• Never fill containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always

place containers on the ground, away from

your vehicle, before filling.

• When practical, remove gas-powered

equipment from the truck or trailer and refuel

it on the ground. If this is not possible,

then refuel such equipment on a trailer with

a portable container, rather than from a

gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times,

until refueling is complete. Do not use a

nozzle lock-open device.

876 - 017 - 7

• Replace gasoline cap securely and wipe up

spilled fuel.

• If fuel is spilled on clothing, change clothing

immediately.

• Use extension cords and receptacles as

specified by the manufacturer for all units with

electric drive motors or electric starting motors.

• Adjust the auger housing height to clear gravel or

crushed rock surface.

• Never attempt to make any adjustments while

the engine (motor) is running (except when

specifically recommended by the manufacturer).

• Always wear safety glasses or eye shields during

operation or while performing an adjustment or

repair to protect eyes from foreign objects that

may be thrown from the machine.

Personal protective equipment

Always use the correct personal protective

equipment when you operate the product.

This includes, at minimum, sturdy footwear,

eye protection and hearing protection. Personal

protective equipment does not erase the risk of injury

but may decrease the grade of injury if an accident

occurs.

• Always wear safety glasses or eye protection

while you operate the product or do maintenance

or repairs.

• Always wear appropriate winter garments when

you operate the product.

• Always use heavy-duty slip-resistant boots with

good ankle support while you operate the

product.

• Do not wear loose fitting clothing that can get

caught in moving parts.

• Use approved protective gloves, if necessary.

For example, when attaching, examining or

cleaning the blade.

• Always use approved ear protection while you

operate the product. Noise for a long period can

cause noise-induced hearing loss.

Safety devices on the product

• Make sure that you regularly do the maintenance

to the product.

• The life of the product increases.

• The risk of accidents decreases.

Let an approved dealer or an approved service

center regularly examine the product to do

adjustments or repairs.

• Do not use a product with damaged protective

equipment. If the product is damaged, speak to

an approved service center.

Muffler

The muffler keeps the noise levels to a minimum and

sends the exhaust fumes away from the operator.

Do not use the product if the muffler is missing or

defective. A defective muffler increases the noise

level and the risk of fire.

WARNING: The muffler becomes

very hot during and after use and when

the engine operates at idle speed. Be

careful near flammable materials and/or

fumes to prevent fire.

Fuel safety

WARNING: Read the warning

instructions that follow before you use

the product.

• Do not start the product if there is fuel or engine

oil on the product. Remove the unwanted fuel/oil

and let the product dry.

• If you spill fuel on your clothing, change clothing

immediately.

• Do not get fuel on your body, it can cause injury.

If you get fuel on your body, use soap and water

to remove the fuel.

• Do not start the product if the engine has a leak.

Examine the engine for leaks regularly.

• Be careful with fuel. Fuel is flammable and the

fumes are explosive and can cause injuries or

death.

• Do not breathe in the fuel fumes, it can cause

injury. Make sure that there is a sufficient airflow.

• Do not smoke near the fuel or the engine.

• Do not put warm objects near the fuel or the

engine.

• Do not add the fuel when the engine is on.

• Make sure that the engine is cool before you

refuel.

• Before you refuel, open the fuel tank cap slowly

and release the pressure carefully.

• Do not add fuel to the engine in an indoor area.

Not sufficient airflow can cause injury or death

because of asphyxiation or carbon monoxide.

• Tighten the fuel tank cap fully. If the fuel tank cap

is not tightened, there is a risk of fire.

• Move the product a minimum of 3 m / 10 ft from

the position where you filled the tank before a

start.

• Do not fill the fuel tank fully. Heat causes the fuel

to expand. Keep a space at the top of the fuel

tank.

Battery safety

WARNING: A damaged battery can

cause an explosion and cause injury.

If the battery has a deformation or

is damaged, speak to an approved

Husqvarna service agent.

8876 - 017 -

WARNING: Read the warning

instructions that follow before you use

the product.

• Use protective glasses when you are near

batteries.

• Do not wear watches, jewelry or other metal

objects near the battery.

• Keep the battery out of reach for children.

• Charge the battery in a space with good airflow.

• Keep flammable materials at a minimum

clearance of 1 m when you charge the battery.

• Discard replaced batteries. See

Disposal on

page 30

• Explosive gases can come from the battery. Do

not smoke near the battery. Keep the battery

away from open flames and sparks.

California Proposition 65

Proposition 65

Safety instructions for maintenance

WARNING: Read the warning

instructions that follow before you use

the product.

• The exhaust fumes from the engine contain

carbon monoxide, an odorless, poisonous and

very dangerous gas. Do not start the engine

indoors or in closed spaces.

• Before you do the maintenance on the product,

stop the engine and remove the ignition cable

from the spark plug.

• Use protective gloves when you do maintenance

on the blades. The blades are very sharp and

cuts can easily occur.

• Accessories and changes to the product that

are not approved by the manufacturer, can

cause serious injury or death. Do not change

the product. Always use accessories that are

approved by the manufacturer.

• If the maintenance is not done correctly and

regularly, the risk of injury and damage to the

product increases.

• Only do the maintenance as given in this

operator's manual. All other servicing must be

done by an approved service agent.

• Let an approved service agent do servicing on

the product regularly.

• Replace damaged, worn or broken parts.

Assembly

To remove the product from the

carton

1. Remove loose parts included with the product.

Cut the four corners of the carton and put the

end panels down flat.

2. Remove the two screws that attach the auger

housing to the pallet. Remove the steel brackets

from the skid plates if they have it.

3. Remove all package materials.

4. Remove the product from the carton and make

sure no loose parts are left in the carton.

Loose parts

Discharge chute (1)

ON/OFF key (s)

876 - 017 - 9

Carriage bolts 5/16-18 x 2 ¼” (2)

Chute retainer

Handle knobs (2)

Locknut 3/8 (1)

Locknut 3/18-16 (1)

Shear pins ¼-20 x 1.81 (6)

Locknuts ¼-20 (6)

Locknut 5/16-18 (1)

Locknut ¼-20 (1)

Nylon washer (1)

Carriage bolt 5/16-18 x 5/8 (1)

Roll pin (1)

Release lever (1)

Discharge chute lever

Spring (1)

Shoulder bolt ¼-20 (1)

Tools required

• 3/8 in. wrench (1)

• 7/16 in. wrench (1)

• 1/2 in. wrench (1)

• 9/16 in. deep socket (1)

To install the handle

1. Lift the upper handle to the operation position.

10 876 - 017 -

2. Adjust the handle position to one of the holes

(C).

3. Put the bolt (B) through the hole (C).

4. Attach the knob (A) to the bolt and tighten the

knob.

5. Attach more carriage bolts (B) and handle knobs

(A) to attach the upper handle to the lower

handle.

To install the discharge chute

1. Put the deflector assembly for the discharge

chute on the top of the discharge chute. The

discharge opening must point to the front of the

product.

2. Put the rotator head (A) on the discharge chute

bracket (J).

3. Align the pins below the rotator head with the

holes in the discharge chute bracket.

4. Put the rotator head on the pin (E), and the

threaded stud (G) on the bracket (F).

5. Attach a locknut (B) on the threaded stud and

tighten.

6. Attach the square retainer (I) with a locknut (H).

7. Put the cables through the hook cable slot (C).

To install the discharge chute lever

and the release cable

1. Push the knob (D) down on the discharge chute

lever. Use a rubber mallet if it is necessary.

2. Attach the release cable to the discharge chute

lever at connection (A).

3. Make sure that the release cable is attached

correctly to the discharge chute.

4. Put the release cable in the groove (B) on the

discharge chute lever.

876 - 017 - 11

5. Install the cable barrel fitting (F) to the release

lever (E).

6. Install the release lever (E) to the discharge

chute lever and attach it with the roll pin (C).

7. Adjust the release cable. See

To adjust the

release cable of the discharge chute on page

8. Adjust the left and right discharge chute cables.

See

To adjust the left and right discharge chute

cables on page 25

To install the remote control for the

discharge chute deflector

1. Attach the cable bracket (A) to the discharge

chute with a carriage bolt (B) and a 5/16-18

locknut (D). Tighten the bolt.

2. Install the cable eyelet (E) to the discharge chute

deflector (F). Use a shoulder bolt (G), a nylon

washer (C), and tighten with a ¼-20 locknut (K).

The cable eyelet will be loose on the shoulder

bolt.

3. Attach the spring (L) between the hex nut (M) on

the rotator head and the hole on the discharge

chute deflector.

To install the speed control cable

1. Put the drive speed lever in the neutral position.

2. Attach the speed control cable (B) to the drive

speed lever with a retaining pin.

3. Attach the speed control cable to the bracket (C)

with 2 ½ in wrenches. Make sure that the drive

speed lever stays in the neutral position.

4. Remove the screw and wing nut (A) on the

bellcrank to let the bellcrank move.

To install the battery ground cable

1. Remove the battery cover.

2. Remove the screw for the battery ground cable.

12 876 - 017 -

3. Install the battery ground cable.

4. Attach the screw for the battery ground cable.

5. Install the battery cover.

To attach replacement shear pins

• Attach the replacement shear pins on the cover

of the remote control or on the battery box.

Operation

Before you start the product

• Keep persons and animals away from the work

area.

• Do daily maintenance. See

Maintenance

schedule on page 17

• Make sure the ignition lead fits correctly on the

spark plug.

• Add oil or gasoline, if necessary. See

To fill fuel

on page 13

To fill the engine with oil

CAUTION: Do not rotate the

dipstick when you check the oil. Do not

fill above the mark.

1. Remove the oil cap and clean the dipstick. See

Product overview on page 3

for the location of

the dipstick.

2. Add oil to the top mark on the dipstick. Use the

dipstick to do a check of the oil level at regular

intervals.

3. Put the oil cap back.

To fill fuel

Do not use gasoline with an octane number less

than 90 RON (86 AKI.) These engines operate best

on unleaded gasoline.

CAUTION:

• Do NOT use expired gasoline,

gasoline with contamination or an oil/

gasoline mixture.

• Do not get dirt or water in the fuel

tank.

• Only use correct fuel containers and

make marks to easier identify them.

• Do NOT use E85 mix fuels.

These engines are not E20/E30/E85

compatible.

• The ethanol contents must be

maximum 10%.

1. Open the fuel tank cap slowly to release the

pressure.

2. Fill slowly with a fuel can. If you spill fuel, remove

it with a cloth and let remaining fuel dry off.

3. Clean the area around the fuel tank cap.

4. Tighten the fuel tank cap fully. If the fuel tank cap

is not tightened, there is a risk of fire.

876 - 017 - 13

5. Move the product a minimum of 3 m (10 ft) from

the position where you filled the tank, before a

start.

To start the engine, manual start

1. Put the ON/OFF key into the ignition slot (B). Do

not turn the key.

2. Put the throttle control (A) to the FAST position.

3. Turn the ON/OFF key to the ON position.

4. Pull the starter rope handle (D).

CAUTION: Do not release the

starter rope handle quickly. Move it

slowly to the start position.

Note: If the starter rope is frozen, slowly pull

out as much rope out of the starter as you can.

Release the starter rope handle. If the engine

does not start, do the procedure again or use the

electric starter.

5. Run the engine 2-3 minutes at low speed before

you start to throw snow.

6. If the engine does not run smoothly, turn it off.

To start the engine, electric start

1. Put the ON/OFF key into the ignition slot (B). Do

not turn the key.

2. Put the throttle control (A) to the FAST position.

3. Put the ON/OFF key to the ON position.

4. Turn the ON/OFF key to START. When the

engine starts, release the key.

CAUTION: Do not run the

starter for more than 5 seconds each

time you try to start. Wait 5 to 10

seconds between each try.

5. Run the engine 2-3 minutes at low speed before

you start to throw snow.

To operate the product

CAUTION: Do not partially engage

drive or auger levers for an extended

period of time; this can lead to premature

wear or burning of the belts.

Note: When both the drive engagement and auger

engagement are engaged, the drive engagement will

lock the auger engagement in position. Use the right

hand to control the snow discharge chute.

1. To engage the auger blades, push the auger

engagement (A) to the handle to engage the

auger and throw snow.

14 876 - 017 -

2. Raise the drive speed control lever (C) from

the middle position to make the product move

forward when the drive engagement (B) is

engaged.

3. Lower the drive speed control lever from

the middle position to make the product

move rearward when the drive engagement is

engaged.

4. To make the product move in the selected

direction, hold the drive engagement against the

handle .

5. If the product has power steering, hold the left

steering trigger (D) to turn left. Hold the right

steering trigger to turn right.

Throttle control

Note: If the snow is wet or heavy, use the fast or

boost modes.

The throttle control adjusts the engine speed. It has

3 modes: boost, fast and slow.

A B C

• Boost (A): to increase speed when the product is

operated but does not throw snow, or to increase

the distance that snow is thrown.

• Fast (B): standard operation

• Slow (C): to decrease the distance that snow is

thrown, or to decrease engine noise

To use the throttle control

• Turn the throttle control to change the engine

speed.

To use the heated handles

• Push the switch to I to start the heated handles.

• Push the switch to O to stop the heated handles.

876 - 017 - 15

To stop the product

1. Turn the key to the STOP position.

2. Remove the ON/OFF key.

To adjust the discharge chute and

the discharge chute deflector

1. Push the release lever (B) on the discharge

chute lever (A) and adjust the discharge chute

to the left or right position.

2. Move the remote control lever (C) to adjust the

snow throwing distance.

a) Move the remote control lever up to decrease

the snow throwing distance.

b) Move the remote control lever down to

increase the snow throwing distance.

To adjust the skid plates

The skid plates prevent damage to the bottom of the

snow thrower. Adjust the skid plates (A) when the

locknut (B) is loose, or the skid plate is not at the

correct distance from the ground. No adjustment is

necessary for standard installation.

1. Loosen the locknut (B) with a 13 mm (½ in.) open

wrench.

2. Move the skid plates (A) up or down.

a) On flat surfaces set the distance between

the scraper bar and the ground to 5-6 mm

(0.2-0.25 in).

b) On rough surfaces set the skid plates (A) in

a position where the scraper bar is above the

top of the ground.

WARNING: Make sure that

gravel and stones do not go into

the product. Objects that eject at

high speed can cause injury.

3. Tighten the locknut (B).

To use the drift cutters (if equipped)

Use the drift cutters to cut through snowdrifts deeper

than the front of the product.

1. Loosen the adjustment nuts (A) on both sides of

the product to allow each drift cutter (B) to be

raised to its highest position.

2. Tighten the nuts.

3. Lower the drift cutters after use.

16 876 - 017 -

To adjust the height of the auger

bucket (for ST 424T/427T/430T only)

1. Push the lever (A) down.

2. Move the handles (B) up or down to adjust the

height of the auger bucket .

3. Release the lever (A) to lock the auger bucket in

position.

Note: The auger bucket can be set to an unlocked

position. This lets the auger bucket adapt to the

terrain. To set the auger bucket to the unlocked

position, push the lever (A) down and to the right.

To prevent freeze-up after use

Note: Controls and moving parts can be blocked

by ice. Do not apply much force to the controls. If

you cannot operate a control or a part, start the

engine and let it operate for some minutes.

1. Start the engine and let it operate for some

minutes. Stop the engine and wait for all moving

parts to stop.

2. Remove snow and loose ice from the product.

3. Remove snow and loose ice from the base of the

discharge chute.

4. Turn the discharge chute deflector to the left

direction and to the right direction to remove ice

and water.

5. Set the key to the "OFF" position.

6. If the product does not have an electric starter,

pull the starter rope handle several times to

remove ice and water.

To get a good result

• Always run the engine at full throttle or near full

throttle.

• Always adapt the speed of the product to the

snow situation and adjust the speed with the

drive speed control lever. Make sure that the

product throws snow evenly.

• It is easier and more efficient to remove snow

immediately after it falls.

• Always throw snow downwind whenever

possible.

• On flat surfaces, like asphalt roads, raise the skid

plates up to 5-6 mm (0.2-0.25 in) off the ground.

• The scraper bar is reversible. When it becomes

worn almost to the edge of the housing, reverse

it. Replace the scraper bar if it is damaged, or if

both sides are worn.

• Do not dispatch the chute deflector if it is

clogged.

• If the product does not move forward due to

unforeseen circumstances, release the drive

engagement immediately or move the ON/OFF

key to the "OFF" position.

Maintenance

Introduction

When the product is in use, bolts can loosen

and components can become worn. This can

cause malfunction like incorrect tolerance clearance,

increased oil consumption, or misalignment of

various components. Do regular maintenance on the

product to prevent malfunction.

Maintenance schedule

Maintenance Daily At 15 hour inter-

vals

At 20 hour inter-

vals

At 40 hour inter-

vals

At 100 hour in-

tervals

Tighten nuts

and screws X

Do a check of

the engine oil

level

Replace the en-

gine oil X

876 - 017 - 17

Maintenance Daily At 15 hour inter-

vals

At 20 hour inter-

vals

At 40 hour inter-

vals

At 100 hour in-

tervals

Do a check of

and adjust the

track tension

(only ST 424T/

427T/430T )

Make sure that

there are no fuel

or oil leaks

Remove obsta-

cles in the auger X

Lubricate the in-

terlock catches 1X

Lubricate the

cable attach-

ments2

Do a check of

the tire pressure

(only ST

424/427/430 )

Inspect and re-

place the spark

plug before use

at the start of a

season and at

recommended

interval

Note: The gearbox does not need maintenance.

To do a general inspection

• Make sure that all nuts and screws on the

product are tightened correctly.

Oil change reminder

The oil change reminder (A) is a function that points

out that an oil change is necessary. The oil change

reminder lights up the oil can symbol on the display

after 20 hours of operation. The oil can symbol is

then on for 2 hours or until a manual reset is done.

To reset the oil change reminder

1. Turn the ON/OFF key to the ON position, and

keep it in the ON position for 1 second.

2. Turn the ON/OFF key to the STOP position, and

keep it in the STOP position for 1 second.

3. Do this procedure 4 more times.

To do a check of the oil level

CAUTION: A too low oil level can

do damage to the engine. Do a check of

the oil level before you start the product.

1. Put the product on level ground.

2. Remove the oil tank cap with the attached

dipstick.

3. Clean the oil from the dipstick.

4. Put the dipstick fully into the oil tank to give a

correct picture of the oil level.

5. Remove the dipstick.

6. Examine the oil level on the dipstick.

1Also lubricate at the beginning of each season.

2Also lubricate at the beginning of each season.

18 876 - 017 -

7. If the oil level is low, fill with engine oil and do a

check of the oil level again.

To replace the engine oil

1. Run the engine a few minutes to make the oil

warm. Warm oil flows better and includes more

contaminants.

WARNING: The engine oil is

hot. Avoid skin contact with the used

engine oil.

2. Put the product on level ground.

3. Remove the ON/OFF key.

4. Put a container below the oil drain plug.

5. Remove the oil drain plug, tip the product and

drain the used oil in the container.

6. Put the product back to the operating position.

7. Install the oil drain plug and tighten it by hand.

8. Fill the engine with oil, see

To fill the engine with

oil on page 13

To lubricate the product

• Lubricate the pivot points (A) with oil.

• Lubricate the engine (B) with oil.

• Lubricate the interlock catches (C) with a small

quantity of lithium grease.

• Lubricate the cable connections for the drive and

auger levers (D) with oil.

Battery

To start with a dead battery

Note: Battery power is necessary to run the fuel

pump for the EFI system.

If the battery power is too low, do 1 of these steps:

• Charge the battery, refer to

To charge the battery

on page 19

• Connect the product to an external power

source, such as the battery to a different vehicle .

Battery maintenance

Note: The battery on your product is maintenance

free. Do not open or remove the caps or the covers.

To charge the battery

Note: Before long term storage, charge the battery

with a battery charger to extend the life of the

battery.

1. Remove the battery cover. Refer to

To replace

the battery on page 19

2. Clean the terminals. Refer to

To clean the battery

and the terminals on page 20

3. Connect the battery charger to the battery

charger connector (A).

Note: For applicable chargers refer to

Accessories on page 31

4. When the battery is charged, disconnect the

battery charger.

5. Install the battery cover.

To replace the battery

WARNING: Risk of electrical shock.

Do not let metal objects touch the 2

battery terminals. This can cause a short

circuit of the battery.

876 - 017 - 19

1. Loosen the knob (A), then tilt the bottom of

the cover in the direction of the engine. Lift the

battery cover off the holders (B).

2. Disconnect the BLACK battery cable.

WARNING: The BLACK cable

must be disconnected first.

3. Disconnect the RED battery cable.

4. Loosen the nuts and remove the battery strap.

5. Carefully remove the battery from the product.

6. Install a new battery.

7. Connect the RED battery cable and tighten the

bolt.

WARNING: Risk of sparks. The

RED cable must be connected first.

8. Connect the BLACK cable and tighten the bolt.

9. Install the battery cover.

To clean the battery and the terminals

1. Remove the battery. Refer to

To replace the

battery on page 19

2. Flush the battery with plain water and let it

become dry.

3. Clean the terminals and battery cable ends with

a wire brush until they are bright.

4. Lubricate the terminals with grease.

5. Install the battery. See

To replace the battery on

page 19

6. Install the battery cover.

Muffler

The muffler keeps the noise levels to a minimum and

sends the exhaust fumes away from the operator.

Do not use the product if the muffler is missing or

defective. A defective muffler increases the noise

level and the risk of fire.

WARNING: The muffler becomes

very hot during and after use and when

the engine operates at idle speed. Be

careful near flammable materials and/or

fumes to prevent fire.

To examine the spark plug

CAUTION: Always use the

recommended spark plug type. Incorrect

spark plug type can cause damage to

the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• If the spark plug is dirty, clean it and make

sure that the electrode gap is correct, refer to

Technical data on page 31

• Replace the spark plug if it is necessary.

To inspect the augers and the

scraper bar

1. Before each use, inspect the augers and the

scraper bar for wear.

2. If the edge of the scraper bar is worn, reverse the

scraper bar. If the scraper bar has damages or is

worn on both edges, replace it.

3. If the edges of the augers are worn, contact an

authorized service center to replace them.

To replace the auger shear pins

The auger shear pins protect the product from

damage. The auger shear pins break if an object

comes into the moving parts.

CAUTION: Use only original

equipment shear pins supplied with the

product.

1. If an auger shear pin breaks, stop the engine and

wait for the moving parts to stop.

2. Remove the ON/OFF key and disconnect the

spark plug cable.

3. Align the hole in the auger hub (B) with the hole

in the auger shaft (C) and install a new ¼ - 20 x 2

shear pin (A).

20 876 - 017 -

La page charge ...

Husqvarna ST 424 Series Snow Thrower Manuel utilisateur

Marque: Husqvarna

Modèle: ST 424 Series Snow Thrower

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Husqvarna ST 424 Series Snow Thrower User manual
español: Husqvarna ST 424 Series Snow Thrower Manual de usuario