Pioneer DMH-W4660NEX Guide de démarrage rapide

Marque: Pioneer

Modèle: DMH-W4660NEX

Taper: Guide de démarrage rapide

Ce manuel convient également à

English Français Español

DMH-WT8600NEX

DMH-WT7600NEX

DMH-WT76NEX

DMH-WC6600NEX

DMH-WC5700NEX

DMH-W4660NEX

DMH-W4600NEX

RDS AV RECEIVER

RÉCEPTEUR AV AVEC RDS

RECEPTOR AV RDS

Installation Manual

Manuel d’installation

Manual de instalación

2En

WARNING

Rear visibility systems (backup cameras)

are required in certain new vehicles sold in

the U.S. and Canada. U.S. regulations

began according to a two year phase-in on

May 1, 2016, and both the U.S. and Canada

require that all such vehicles manufactured

on or after May 1, 2018 have rear visibility

systems. Owners of vehicles equipped

with compliant rear visibility systems

should not install or use this product in

a way that alters or disables that

system's compliance with applicable

regulations. If you are unsure whether

your vehicle has a rear visibility system

subject to the U.S. or Canadian regulations,

please contact the vehicle manufacturer or

dealer.

If your vehicle has a compliant backup

camera that displays the backup view

through the factory receiver, do not use

the Pioneer receiver unless it is connected

to and displays the same view as the

factory backup camera. Connection to the

factory backup camera will require an

adaptor, sold separately. Not all vehicles

may be able to connect. Please check with

a qualified professional installer for

installation options specific to your vehicle.

• Do not operate this product, any

applications, or the rear view camera

option (if purchased) if doing so will

divert your attention in any way from the

safe operation of your vehicle. Always

observe safe driving rules and follow all

existing traffic regulations. If you

experience difficulty in operating this

product, pull over, park your vehicle in a

safe location and apply the parking brake

before making the necessary

adjustments.

• Do not install this product where it may

(i) obstruct the driver’s vision,

(ii) impair the performance of any of the

vehicle’s operating systems of safety

features, including airbags, hazard lamp

buttons, or

(iii) impair the driver’s ability to safely

operate the vehicle.

In some cases, it may not be possible to

install this product because of the vehicle

type or the shape of the vehicle interior.

Important safety

information

Connection

Precautions

Your new product and this

manual

WARNING

Pioneer does not recommend that you

install this product yourself. This product is

designed for professional installation only.

We recommend that only authorized

Pioneer service personnel, who have

special training and experience in mobile

electronics, set up and install this product.

NEVER SERVICE THIS PRODUCT YOURSELF.

Installing or servicing this product and its

connecting cables may expose you to the

risk of electric shock or other hazards, and

can cause damage to this product that is

not covered by warranty.

CAUTION

• Secure all wiring with cable clamps or

electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger

compartment into the engine

compartment. If the yellow lead’s

insulation tears as a result of contact with

metal parts, short-circuiting can occur,

resulting in considerable danger.

• It is extremely dangerous to allow cables

to become wound around the steering

column or shift lever. Be sure to install

this product, its cables, and wiring away

in such so that they will not obstruct or

hinder driving.

• Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts,

especially the steering wheel, shift lever,

parking brake, sliding seat tracks, doors,

or any of the vehicle’s controls.

• Do not route wires where they will be

exposed to high temperatures. If the

insulation heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

• Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse

resistor or filter, etc.) may fail to work

properly.

• Never feed power to other electronic

products by cutting the insulation of the

power supply lead of this product and

tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

• Use this unit with a 12-volt battery and

negative grounding only. Failure to do so

may result in a fire or malfunction.

• To avoid shorts in the electrical system,

be sure to disconnect the (–) battery

cable before installation.

WARNING

• When speaker output is used by 4

channels , use speakers over 50 W

(Maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use 1

Ω to 3 Ω speakers for this unit.

• When rear speaker output is used by 2 Ω

of subwoofer, use speakers over 70 W

(Maximum input power).

*Please refer to connection for a

connection method.

Important safeguards

Precautions before

connecting the system

Before installing this

product

To prevent damage

3En

English

• The black lead is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire

first. Ensure that the ground wire is

properly connected to metal parts of the

car’s body. The ground wire of the power

amp and the one of this unit or any other

device must be connected to the car

separately with different screws. If the

screw for the ground wire loosens or falls

out, it could result in fire generation of

smoke or malfunction.

• When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

• When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

• This product cannot be installed in a

vehicle without ACC (accessory) position

on the ignition switch.

• To avoid short-circuiting, cover the

disconnected lead with insulating tape. It

is especially important to insulate all

unused speaker leads, which if left

uncovered may cause a short circuit.

• For connecting a power amp or other

devices to this product, refer to the

manual for the product to be connected.

• The graphical symbol placed on

the product means direct current.

• When the ignition switch is turned on

(ACC ON), a control signal is output

through the blue/white lead. Connect to

an external power amp’s system remote

control terminal, the auto-antenna relay

control terminal, or the antenna booster

power control terminal (max. 300 mA 12

V DC). The control signal is output

through the blue/white lead, even if the

audio source is switched off.

Important

When this product is in [Power OFF] mode,

the control signal is also turned off. If

[Power OFF] mode is canceled, the control

signal is output again and the antenna is

extended with the auto antenna function

(if the antenna is being used). Be careful so

that the extended antenna does not come

into contact with any obstacles.

Ground wire

POWER AMP

Other devices

(Another electronic

device in the car)

Metal parts of car’s

body

*1 Not supplied for this unit

ACC position

No ACC position

Notice for the blue/

white lead

▶DMH-WT8600NEX/DMH-

WT7600NEX/DMH-WT76NEX/DMH-

WC6600NEX/DMH-WC5700NEX

▶DMH-W4660NEX/DMH-W4600NEX

GPS antenna 3.55 m (11 ft. 8 in.)

Microphone 3 m (9 ft. 10-1/8 in.)

iDatalink or Metra adaptor input

Refer to the instruction manual for the

iDataLink or Metra adaptor (sold

separately).

Monitor cable connector*

Connect to LCD screen.

Antenna jack

This product

Pre out supply

Power supply

Fuse (10A)

Wired remote input

Hard-wired remote control adaptor can

be connected (sold separately).

SiriusXM Connect Vehicle Tuner

Refer to the instruction manual for

SiriusXM Connect Vehicle Tuner (sold

separately).

* Monitor cable and connector are in the front

panel. (DMH-WT8600NEX, DMH-WT7600NEX,

DMH-WT76NEX)

NOTES

• Before using and/or connecting the

iDatalink Maestro adaptor (sold

separately), you will need to first flash the

Maestro module with the appropriate

vehicle and head unit firmware. You can

find the device number that is required

for the activation on the followings (refer

to the Operation Manual.):

–The label on the packaging of this

product

–The label on this product

– The [Firmware Information] screen

• When the iDatalink Maestro adaptor is

connected, use the microphone of this

unit to perform voice operations for

Apple CarPlay, Android Auto, or Amazon

Alexa.

WARNING

IMPROPER CONNECTION MAY RESULT IN

SERIOUS DAMAGE OR INJURY

Rear panel (main

terminals)

Power cord

4En

INCLUDING ELECTRICAL SHOCK, AND

INTERFERENCE WITH THE OPERATION

OF THE VEHICLE'S ANTILOCK BRAKING

SYSTEM, AUTOMATIC TRANSMISSION

AND SPEEDOMETER INDICATION.

To power supply

Power cord

Yellow

To terminal supplied with power

regardless of ignition switch position.

Red

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF

Orange/white

To lighting switch terminal.

Black (ground)

To vehicle (metal) body.

Violet/white

Of the two lead wires connected to the

back lamp, connect the one in which

the voltage changes when the gear shift

is in the REVERSE (R) position. This

connection enables the unit to sense

whether the car is moving forward or

backward.

Pink

Car speed signal input

Blue/white

Connect to system control terminal of

the power amp (max. 300 mA 12 V DC).

Light green

Used to detect the ON/OFF status of the

parking brake. This lead must be

connected to the power supply side of

the parking brake switch.

If this connection is made incorrectly

or omitted, certain functions of this

product will be unusable.

Power supply side

Parking brake switch

Ground side

NOTE

The position of the speed detection circuit

and the position of the parking brake

switch vary depending on the vehicle

model. For details, consult your authorized

Pioneer dealer or an installation

professional.

Perform these connections when using a

subwoofer without the optional amplifier.

Speaker leads

To power supply

Power cord

Left

Right

Front speaker (STD) or high range

speaker (NW)

Rear speaker (STD) or middle range

speaker (NW)

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

Subwoofer (4 Ω)

When using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do

not connect anything to the green and

green/black leads.

Not used.

Subwoofer (4 Ω) × 2

NOTES

• When a subwoofer is connected to this

product instead of a rear speaker, change

the rear output setting in the initial

setting. The subwoofer output of this

product is monaural.

For details, refer to the Operation Manual.

• With a two-speaker system, do not

connect anything to the speaker leads

that are not connected to speakers.

5En

English

Important

The speaker leads are not used when this connection is in use.

Subwoofer output (SUBWOOFER OUTPUT) 23 cm (9 in.) (STD)

Low range output (NW)

RCA cable (sold separately)

Power amp

Front output (FRONT OUTPUT) 15 cm (5-7/8 in.) (STD)

High range output (NW)

Rear output (REAR OUTPUT) 15 cm (5-7/8 in.) (STD)

Middle range output (NW)

Yellow/black (MUTE)

If you use an equipment with Mute function, wire this lead to the Audio Mute lead on

that equipment. If not, keep the Audio Mute lead free of any connections.

Pre out cord

To pre out supply

System remote control

Connect to Blue/white cable (max. 300 mA 12 V DC).

Power amp (sold separately)

Rear speaker (STD)

Middle range speaker (NW)

Front speaker (STD)

High range speaker (NW)

Subwoofer (STD)

Low range speaker (NW)

NOTE

Select the appropriate speaker mode between standard mode (STD) and network mode

(NW). For details, refer to the Operation Manual.

6En

NOTES

• For details on how to connect an external

device using a separately sold cable, refer

to the manual for the cable.

• For details concerning the connection,

operations and compatibility of the

iPhone, refer to the Operation Manual.

• For details concerning the connection

and operations of the smartphone, refer

to the Operation Manual.

• The supplied USB Type-C® cable and the

USB Type-C to USB Type-A adaptor are for

connecting a USB storage device to this

unit only. Do not use the cable and the

adaptor for other products or purposes.

This product

USB Type-C port

USB Type-C cable 1.5 m (4 ft. 11 in.)

USB Type-C to USB Type-A adaptor

USB interface cable for iPhone (CD-IU52)

(sold separately)

iPhone

TIP

When a USB Type-C to Lightning

connector cable (Apple Inc. product) (sold

separately) is used to connect this unit to

an iPhone that supports USB-PD, quick

charging is performed for the iPhone.

NOTE

When you use a USB Type-C to Lightning

connector cable (Apple Inc. product) (sold

separately), follow the instructions

provided with the cable.

This product

USB Type-C port

USB Type-C cable 1.5 m (4 ft. 11 in.)

USB Type-C to USB Type-C interface

cable (CD-CCU500) (sold separately)

Smartphone

TIPS

• Use the supplied USB Type-C to USB

Type-A adaptor with a USB Type-A to

micro USB B cable (CD-MU200) (sold

separately) if your smartphone has a

micro USB B port.

• When a USB Type-C to USB Type-C cable

(sold separately) is used to connect this

unit to a smartphone, quick charging is

performed.

iPhone and

smartphone

iPhone

Smartphone (Android™

device)

NOTES

• If you use a cable other than those

suggested in the illustration, the main

unit may not function properly.

• Android is a trademark of Google LLC.

When you use the rear view camera, the

rear view image is automatically switched

from the video by moving the shift lever to

REVERSE (R). Camera View mode also

allows you to check what is behind you

while driving.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR

IMAGE REAR VIEW CAMERA. OTHER USE

MAY RESULT IN INJURY OR DAMAGE.

CAUTION

• The screen image may appear reversed.

• With the rear view camera you can keep

an eye on trailers, or back into a tight

parking spot. Do not use for

entertainment purposes.

• Objects in rear view may appear closer or

more distant than in reality.

• The image area of full-screen images

displayed while backing or checking the

rear of the vehicle may differ slightly.

This product

Pre out supply

Power supply

To pre out supply

To power supply

Pre out cord

Power cord

Violet/white (REVERSE-GEAR SIGNAL

INPUT)

Brown (REAR VIEW CAMERA IN) 23 cm

(9 in.)

Yellow* (SECOND CAMERA INPUT) 23

cm (9 in.)

Rear view camera (ND-BC8) (sold

separately)

To video output

RCA power supply cable (supplied with

ND-BC8)

Camera

7En

English

RCA cable (sold separately)

View camera (sold separately)

* Not available for DMH-W4600NEX

NOTES

• Connect only the rear view camera to

brown cable. Do not connect any other

equipment.

• Some appropriate settings are required

to use rear view cameras. For details, refer

to the Operation Manual.

This product

Pre out supply

To pre out supply

Pre out cord

AUX input (AUX IN) 15 cm (5-7/8 in.)

Mini-jack AV cable (sold separately)

Yellow

Red, white

External video

component

Using an AUX input

RCA cables (sold separately)

To video output

To audio output

External video component (sold

separately)

NOTE

The appropriate setting is required to use

the external video component. For details,

refer to the Operation Manual.

CAUTION

Be sure to use a mini-jack AV cable (sold

separately) for wiring. If you use other

cables, the wiring position might differ

resulting in disturbed images and sounds.

This product

Micro HDMI port

Micro HDMI to HDMI cable (sold

separately)

HDMI device (sold separately)

This product

Pre out supply

To pre out supply

Pre out cord

Yellow (REAR MONITOR OUTPUT) 30

cm (11-7/8 in.)

RCA cable (sold separately)

To Video input

Rear display with RCA input (sold

separately)

WARNING

NEVER install the rear display in a location

that enables the driver to watch the video

source while driving.

This product’s rear video output is for

connection of a display to enable

Using an HDMI input

L : Left audio (White)

R : Right audio (Red)

V : Video (Yellow)

G : Ground

Rear display

8En

passengers in the rear seats to watch the

video source.

CAUTION

• Never install this product in places where,

or in a manner that:

– Could injure the driver or passengers if

the vehicle stops suddenly.

– May interfere with the driver’s operation

of the vehicle, such as on the floor in

front of the driver’s seat, or close to the

steering wheel or shift lever.

• To ensure proper installation, be sure to

use the supplied parts in the manner

specified. If any parts are not supplied

with this product, use compatible parts in

the manner specified after you have the

part compatibility checked by your

dealer. If parts other than supplied or

compatible ones are used, they may

damage internal parts of this product or

they may work loose and the product

may become detached.

• It is extremely dangerous to allow cables

to become wound around the steering

column or shift lever. Be sure to install

this product, its cables, and wiring away

in such so that they will not obstruct or

hinder driving.

• Make sure that leads cannot get caught

in a door or the sliding mechanism of a

seat, resulting in a short circuit.

• Please confirm the proper function of

your vehicle’s other equipment after

installation of this product.

• Do not install this product where it may

(i) obstruct the driver’s vision,

(ii) impair the performance of any of the

vehicle’s operating systems or safety

features, including airbags, hazard lamp

buttons or

(iii) impair the driver’s ability to safely

operate the vehicle.

• Never install this product in front of or

next to the place in the dashboard, door,

or pillar from which one of your vehicle’s

airbags would deploy. Please refer to your

vehicle’s owner’s manual for reference to

the deployment area of the frontal

airbags.

• Consult with your nearest dealer if

installation requires drilling holes or

other modifications of the vehicle.

• Before making a final installation of this

product, temporarily connect the wiring

to confirm that the connections are

correct and the system works properly.

• Do not install this product in places

subject to high temperatures or

humidity, such as:

– Places close to a heater, vent or air

conditioner.

–Places exposed to direct sunlight, such

as on top of the dashboard.

– Places that may be exposed to rain,

such as close to the door or on the

vehicle’s floor.

• Install this product horizontally on a

surface within 0 to 40 degrees tolerance

(within 5 degrees to the left or right).

Improper installation of the unit with the

surface tilted more than these tolerances

increases the potential for errors in the

Installation

Precautions before

installation

Before installing

Installation notes

9En

English

vehicle’s location display, and might

otherwise cause reduced display

performance.

• When installing, to ensure proper heat

dispersal when using this unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

• Do not forcibly insert this unit into the

dashboard/console when installing.

Applying excessive force to the

connectors (HDMI and USB Type-C) may

cause a malfunction.

• The cords must not cover up the area

shown in the figure below. This is

necessary to allow the amplifiers to

radiate freely. (DMH-WC6600NEX/DMH-

WC5700NEX)

Do not cover this area

▶DMH-WT8600NEX/DMH-

WT7600NEX/DMH-WT76NEX

Installation tips

The following procedure describes how to

install this product with an LCD screen

attached to the unit. Depending on the

vehicle or installation location, you may

need to adjust the mounting position of

the LCD screen in order to prevent

impairment of vehicle driving operations.

For details on the mounting LCD screen

dimensions, refer to The adjusting position

and mounting dimension of the display

(page 12) before installing.

WARNING

Do not use a mounting sleeve to install this

unit to prevent it from popping out or

rattling.

1 Adjust the front-back position of the

front panel by removing the flush

surface screws on the front edge of the

unit ( ) then fix the face panel by

using the screw ( ) (optional).

Depending on the vehicle, the front-

back position of the front panel may

need to be adjusted to mount the LCD

screen. Slide the face panel to the front

before installing the unit to the vehicle.

Leave ample

space

5 cm

Installation using the

screw holes on the side

of this product

Screw

2 Fasten this product to the factory

radio-mounting bracket.

Position this product so that its screw

holes are aligned with the screw holes

of the bracket, and tighten the screws at

three locations on each side.

TIP

The amount of this unit's protrusion from

the dashboard/console can be adjusted by

shifting the position of the screw hole of

this unit to the factory radio-mounting

bracket.

Factory radio-mounting bracket

If the pawl interferes with

installation, you may bend it down

out of the way.

Dashboard or console

Binding head screw (8 mm) or flush

surface screw

Be sure to use the screws supplied

with this product.

3 Fasten the LCD screen mounting

bracket to the main unit at the suitable

position.

LCD screen mounting bracket

Binding head screw (4 mm × 6 mm)

TIP

The mounting left-center-right position of

the LCD screen mounting bracket can be

changed depending on the vehicle or

installation location of the main unit.

10En

4 Detach the monitor cable cover from

the LCD screen ( ), then connect the

monitor cable to the LCD screen ( ).

After that, attach the LCD screen with

adjusting the up-down position ( ) to

this unit by using the screws each side

().

Monitor cover

Binding head screw (4 mm × 12 mm)

5 Secure the monitor cable to the hook

on the back of the LCD screen then

attach the monitor cover ( ) by using

the screws ( ).

Monitor cover

Machine screw (2 mm × 4 mm)

NOTES

• Be careful not to lose the small screws

(2 mm × 4 mm) for attaching the

monitor cover.

• It is recommended that you use a

magnetic screwdriver when attaching

the monitor cover.

• Two spare screws (2 mm × 4 mm) for

attaching the monitor cover are

included.

▶DMH-WC6600NEX/DMH-WC5700NEX

Installation tips

The following procedure describes how to

use the supplied parts to install this

product with the LCD screen attached to

the unit. It is also possible to install this

product so that the LCD screen is separate

from the unit. For details, visit the Pioneer

website for your region.

For some types of vehicles, it is necessary

to use an installation kit (sold separately)

when installing. For details, visit the

Pioneer website for your region.

1 First attach the supplied side brackets

to the LCD screen ( ), then attach

them to this unit ( ). After that,

connect the monitor cable to the LCD

screen ( ).

Side bracket (for attaching LCD

screen to unit)

Binding head screw (5 mm)

Be sure to use the screws supplied

with this product.

Monitor cable

Attach the monitor cable to the unit

with heat resistant tape (sold

separately).

2 Fasten this product to the factory

radio-mounting bracket.

Position this product so that its screw

holes are aligned with the screw holes

of the bracket, and tighten the screws at

three locations on each side.

Use either the binding head screws or

flush surface screws, depending on the

shape of the bracket’s screw holes.

TIP

The amount of this unit's protrusion from

the dashboard/console can be adjusted by

shifting the position of the screw hole of

this unit to the factory radio-mounting

bracket.

Factory radio-mounting bracket

If the pawl interferes with

installation, you may bend it down

out of the way.

Dashboard or console

Binding head screw (8 mm) or flush

surface screw

Be sure to use the screws supplied

with this product.

▶DMH-W4600NEX/DMH-W4600NEX

1 Fasten this product to the factory

radio-mounting bracket.

Position this product so that its screw

holes are aligned with the screw holes

of the bracket, and tighten the screws at

three locations on each side.

Use either the truss head screws (5 mm

× 9 mm) or flush surface screws (5 mm ×

9 mm), depending on the shape of the

bracket’s screw holes.

11En

English

TIP

The amount of this unit's protrusion from

the dashboard/console can be adjusted by

shifting the position of the screw hole of

this unit to the factory radio-mounting

bracket.

Factory radio-mounting bracket

If the pawl interferes with

installation, you may bend it down

out of the way.

Dashboard or console

Truss head screw or flush surface

screw

Be sure to use the screws supplied

with this product.

CAUTION

Do not cut the GPS antenna lead to

shorten it or use an extension to make it

longer. Altering the antenna cable could

result in a short circuit or malfunction and

permanent damage to this product.

• The antenna should be installed on a

level surface where radio waves will be

blocked as little as possible. Radio waves

cannot be received by the antenna if

reception from the satellite is blocked.

Dashboard

Rear shelf

• When installing the GPS antenna inside

the vehicle, be sure to use the metal

sheet provided with your system. If this is

not used, the reception sensitivity will be

poor.

• Do not cut the accessory metal sheet.

This would reduce the sensitivity of the

GPS antenna.

• Take care not to pull the antenna lead

when removing the GPS antenna. The

lead may become detached.

• Do not paint the GPS antenna, as this

may affect its performance.

Installing the GPS

antenna

Installation notes

WARNING

Do not install the GPS antenna over any sensors or vents on the dashboard of the vehicle, as

doing so may interfere with the proper functioning of such sensors or vents and may

compromise the ability of the metal sheet under the GPS antenna to properly and securely

affix to the dashboard.

GPS antenna

Metal sheet

Peel off the protective sheet on the rear.

Double-sided tape

Clamps

Use clamps to secure the lead where necessary inside the vehicle.

NOTES

• Affix the metal sheet on the surface as level as possible where the GPS antenna faces the

window.

• Affix the GPS antenna on the metal sheet using the double-sided tape.

• The metal sheet contains a strong adhesive which may leave a mark on the surface if it is

removed.

• When attaching the metal sheet, do not cut it into small pieces.

• Some models use window glass that does not allow signals from GPS satellites to pass

through. On such models, install the GPS antenna on the outside of the vehicle.

When installing the antenna inside the vehicle (on the dashboard or

rear shelf)

Make sure the surface is free of

moisture, dust, grime, oil, etc.,

before affixing the metal sheet.

12En

• Install the microphone in a place where

its direction and distance from the driver

make it easiest to pick up the driver’s

voice.

• Be sure to turn off (ACC OFF) the product

before connecting the microphone.

• Depending on the vehicle model, the

microphone cable length may be too

short when you mount the microphone

on the sun visor. In such cases, install the

microphone on the steering column.

1 Fit the microphone lead into the

groove.

Microphone lead

Groove

2 Attach the microphone clip to the sun

visor.

Microphone clip

Clamps

Use separately sold clamps to secure

the lead where necessary inside the

vehicle.

Install the microphone on the sun visor

when it is in the up position. It cannot

recognize the driver’s voice if the sun

visor is in the down position.

1 Detach the microphone base from the

microphone clip by sliding the

microphone base while pressing the

tab.

Tab

Microphone base

2 Mount the microphone on the

steering column.

Installing the

microphone

Mounting on the sun visor

Installation on the steering

column

Double-sided tape

Clamps

Use separately sold clamps to secure

the lead where necessary inside the

vehicle.

NOTE

Install the microphone on the steering

column, keeping it away from the steering

wheel.

The microphone angle can be adjusted.

▶DMH-WT8600NEX/DMH-

WT7600NEX/DMH-WT76NEX

The mounting position of this unit’s display

can be adjusted (front-back/up-down/

right-left/angle). When mounting the

display, adjust the mounting position and

dimensions so that your view is clear and it

does not impair your driving.

WARNING

Make sure that none of the following

conditions exist when mounting the

display. Otherwise, an accident may occur.

• It impairs the operation of the steering

wheel and levers (shift lever, windshield

wiper switch, turn signal switch, etc.).

• It impairs the operation of the airbags.

• It significantly impairs the operation of

the hazard switch.

• It impairs the ability to identify or operate

other control switches.

• You are unable to see gauges, meters or

warning indicators.

• It interferes with in-vehicle devices

(switches, panel, glove compartment, cup

holder, etc.).

Depending on the vehicle, the display may

hinder access to the glove compartment or

cup holder, or it may block the air

conditioner vents.

Adjusting the microphone angle

The adjusting position

and mounting

dimension of the

display

13En

English

▶Front-back position

▶Left-right position

DMH-WT8600NEX

Display mounting dimensions

and adjustable positions

Front

75 (3)

38.1 (1-1/2)

mm (in.)

Back

55 (2-1/8)

18.1 (1/4)

mm (in.)

Center

128.2 (5) 128.2 (5)

mm (in.)

Left

158.2 (6-1/4) 98.2 (3-7/8)

mm (in.)

Right

158.2 (6-1/4)98.2 (3-7/8)

mm (in.)

DMH-WT7600NEX/DMH-WT76NEX

Center

115.4 (4-1/2) 115.4 (4-1/2)

mm (in.)

Left

145.4 (5-3/4) 85.4 (3-3/8)

mm (in.)

Right

145.4 (5-3/4)85.4 (3-3/8)

mm (in.)

14En

WARNING

Keep hands and fingers clear of this product when adjusting the LCD screen angle. Be

especially cautious of children’s hands and fingers.

NOTE

Certain positions cannot be adjusted and held depending on the up-down position and the

front-back position. For details, refer to Mounting dimension with the angle range of the

display (page 14).

Adjustable display angles and up-down positions

60˚

15˚

15 (5/8)

30 (1-1/8)

45 (1-3/4)

60 (2-3/8)

mm (in.)

▶Front angle range

Mounting dimension with the angle range of the display

Angle range of front position

-15

(-5/8)

-30

(-1-1/8)

-45

(-1-3/4)

-60

(-2-3/8)

60˚

35˚ -15˚

mm (in.)

15En

English

DMH-WT8600NEX

Angle 60˚ Angle 35˚ Angle -15˚

A’

B’

A’

B’

58.3

(2-1/4)

A’ B B’ C A A’ B B’ C A A’ B B’ C

mm (in.)

166.1

(6-1/2)

107.3

(4-1/4)

95.0

(3-3/4)

82.7

(3-1/4)

70.5

(2-3/4)

58.2

(2-1/4)

137.3

(5-3/8)

128.7

(5)

120.1

(4-3/4)

111.5

(4-8/3)

102.9

(4)

149.0

(5-7/8)

134.6

(5-1/4)

120.1

(4-3/4)

105.6

(4-1/8)

91.1

(3-5/8)

34.6

(1-3/8)

38.4

(1-1/2)

42.3

(1-5/8)

46.2

(1-3/4)

50.1

(2)

-14.8

(-1/2)

39.4

(1-1/2)

33.4

(1-1/4)

-15

(-5/8)

-30

(-1-1/8)

-45

(-1-3/4)

-60

(-2-3/8)

-12.5

(-1/2)

-24.8

(1)

-37.1

(1-1/2)

-49.4

(-1-7/8)

-61.7

(-2-3/8)

53.4

(2-1/8)

44.8

(1-3/4)

36.2

(1-3/8)

27.6

(1)

19.0

(3/4)

35.9

(1-3/8)

27.3

(1)

18.7

(3/4)

10.1

(3/8)

1.5

(1/8)

7.7

(1/4)

-6.8

(-1/4)

-21.2

(-7/8)

-35.7

(-1-3/8)

-50.2

(-2)

72.4

(2-7/8)

76.3

(3)

80.2

(3-1/

84.1

(3-1/4)

88.0

(3-1/2)

14.3

(1/2)

18.2

(3/4)

22.1

(7/8)

26.0

(1)

29.9

(1-1/8)

DMH-WT7600NEX/DMH-WT76NEX

Angle 60˚ Angle 35˚ Angle -15˚

A’

B’

A’

B’

50.6

(2)

A’ B B’ C A A’ B B’ C A A’ B B’ C

mm (in.)

152.6

(6)

94.6

(3-3/4)

82.3

(3-1/4)

70.1

(2-3/4)

57.8

(2-1/4)

45.5

(1-3/4)

128.4

(5)

119.8

(4-5/8)

111.2

(4-3/8)

102.6

(4)

94.0

(3-3/4)

134.1

(5-1/4)

119.6

(4-5/8)

105.1

(4-1/8)

90.6

(3-1/2)

76.1

(3)

38.6

(1-1/2)

42.5

(1-5/8)

46.3

(1-3/4)

50.2

(2)

54.1

(2-1/8)

-14.8

(-1/2)

39.4

(1-1/2)

33.4

(1-1/4)

-15

(-5/8)

-30

(-1-1/8)

-45

(-1-3/4)

-60

(-2-3/8)

-12.5

(-1/2)

-24.8

(1)

-37.1

(1-1/2)

-49.4

(-1-7/8)

-61.7

(-2-3/8)

53.4

(2-1/8)

44.8

(1-3/4)

36.2

(1-3/8)

27.6

(1)

19.0

(3/4)

35.9

(1-3/8)

27.3

(1)

18.7

(3/4)

10.1

(3/8)

1.5

(1/8)

7.7

(1/4)

-6.8

(-1/4)

-21.2

(-7/8)

-35.7

(-1-3/8)

-50.2

(-2)

72.4

(2-7/8)

76.3

(3)

80.2

(3-1/

84.1

(3-1/4)

88.0

(3-1/2)

14.3

(1/2)

18.2

(3/4)

22.1

(7/8)

26.0

(1)

29.9

(1-1/8)

16En

▶Back angle range

Angle range of back position

-15

(-5/8)

-30

(-1-1/8)

-45

(-1-3/4)

-60

(-2-3/8)

60˚

25˚ -15˚

mm (in.)

DMH-WT8600NEX

Angle 60˚

Angle 25˚ Angle -15˚

A’

B’

A’

B’

58.3

(2-1/4)

A’ B B’ C A A’ B B’ C A A’ B B’ C

mm (in.)

146.1

(5-3/4)

122.7

(4-3/4)

109.1

(4-1/4)

95.5

(3-3/4)

81.9

(3-1/4)

68.3

(2-5/8)

100.3

(3-7/8)

94.0

(3-3/4)

87.7

(3-3/8)

81.3

(3-1/4)

75.0

(3)

149.0

(5-7/8)

134.6

(5-1/4)

120.1

(4-3/4)

105.6

(4-1/8)

91.1

(3-5/8)

14.6

(1/2)

18.4

(3/4)

22.3

(7/8)

26.2

(1)

30.1

(1-1/8)

-15

(-5/8)

-30

(-1-1/8)

-45

(-1-3/4)

-60

(-2-3/8)

-9.9

(3/8)

-23.5

(-7/8)

-37.1

(1-1/2)

-50.7

(-2)

-64.3

(-2-1/2)

38.5

(1-1/2)

32.2

(1-1/4)

25.8

(1)

19.5

(3/4)

13.2

(1/2)

16.7

(5/8)

10.4

(3/8)

4.1

(1/4)

-2.3

(-1/8)

-8.6

(-3/8)

52.4

(2)

56.3

(2-1/4)

60.2

(2-3/8)

64.1

(2-1/2)

68.0

(2-5/8)

-5.7

(-1/4)

-1.8

(-1/8)

2.1

(1/8)

6.0

(1/4)

9.9

(3/8)

7.7

(1/4)

-6.8

(-1/4)

-21.2

(-7/8)

-35.7

(-1-3/8)

-50.2

(-2)

-14.8

(-1/2)

19.4

(3/4)

13.4

(1/2)

17En

English

DMH-WT7600NEX/DMH-WT76NEX

NOTES

• Where there are no numbers in the table, this indicates that the display cannot be

adjusted and held with that angle and dimensions.

• The displayed angle range is the movable range of this unit, and it may vary depending on

the vehicle in which the unit is installed.

Angle 60˚

Angle 25˚ Angle -15˚

A’

B’

A’

B’

50.6

(2)

A’ B B’ C A A’ B B’ C A A’ B B’ C

mm (in.)

132.6

(5-1/4)

108.6

(4-1/4)

95.0

(3-3/4)

81.4

(3-1/4)

67.8

(2-5/8)

54.2

(2-1/8)

93.8

(3-5/8)

87.5

(3-3/8)

81.1

(3-1/4)

74.8

(2-7/8)

68.4

(2-5/8)

134.1

(5-1/4)

119.6

(4-5/8)

105.1

(4-1/8)

90.6

(3-1/2)

76.1

(3)

18.6

(3/4)

22.5

(7/8)

26.3

(1)

30.2

(1-1/8)

34.1

(1-3/8)

-15

(-5/8)

-30

(-1-1/8)

-45

(-1-3/4)

-60

(-2-3/8)

-9.9

(3/8)

-23.5

(-7/8)

-37.1

(1-1/2)

-50.7

(-2)

-64.3

(-2-1/2)

38.5

(1-1/2)

32.2

(1-1/4)

25.8

(1)

19.5

(3/4)

13.2

(1/2)

16.7

(5/8)

10.4

(3/8)

4.1

(1/4)

-2.3

(-1/8)

-8.6

(-3/8)

52.4

(2)

56.3

(2-1/4)

60.2

(2-3/8)

64.1

(2-1/2)

68.0

(2-5/8)

-5.7

(-1/4)

-1.8

(-1/8)

2.1

(1/8)

6.0

(1/4)

9.9

(3/8)

7.7

(1/4)

-6.8

(-1/4)

-21.2

(-7/8)

-35.7

(-1-3/8)

-50.2

(-2)

-14.8

(-1/2)

19.4

(3/4)

13.4

(1/2)

2Fr

ATTENTION

Les systèmes de surveillance de marche

arrière (caméras de secours) sont requis

dans certains véhicules neufs vendus aux

États-Unis et au Canada. La réglementation

des États-Unis a commencé avec une

intégration basée sur deux ans débutant le

1er mai 2016, et où les États-Unis et le

Canada exigent que tous véhicules

fabriqués à partir du 1er mai 2018 soient

équipés de système de surveillance de

marche arrière. Les propriétaires de

véhicules déjà équipés de systèmes de

surveillance de marche arrière ne

devraient pas installer ou utiliser ce

produit de manière à altérer ou encore

désactiver les fonctions de ce système

basé sur les réglementations en vigueur.

Si vous ne savez pas si votre véhicule a un

système de la sorte ou si il est sujet aux

réglementations Américaines ou

Canadiennes, nous vous invitons à

contacter le fabricant ou le

concessionnaire du véhicule.

Si votre véhicule dispose d'une caméra de

marche arrière compatible affichant un vue

arrière via le récepteur (radio) d'origine,

n'utilisez pas le récepteur Pioneer, à moins

qu'il ne soit connecté et en mesure

d'afficher la même vue que la caméra de

marche arrière d'usine offre à la base. La

connexion à la caméra d'usine nécessitera

possiblement un adaptateur, vendu

séparément. Certains véhicules peuvent

être incompatibles. Vérifiez avec un

installateur professionnel qualifié pour les

options d'installation spécifiques à votre

véhicule.

• N’utilisez pas ce produit, les applications

ou la caméra de recul en option (le cas

échéant) si cela vous distrait de quelque

façon affectant l’utilisation sécuritaire de

votre véhicule. Respectez toujours les

règles de conduite sécuritaire et toute la

réglementation routière en vigueur. Si

vous avez du mal à utiliser ce produit,

stationnez votre véhicule dans un

emplacement sûr et engagez le frein de

stationnement avant d’effectuer les

réglages nécessaires.

• N’installez pas ce produit là où il risque

(i) de gêner la vision du conducteur,

Importantes informations

de sécurité

Connexion

Précautions

Votre nouveau produit et ce

manuel

(ii) d’affecter le fonctionnement de tout

système ou de tout dispositif de sécurité

du véhicule, y compris les coussins de

sécurité gonflables ou les boutons de

feux de détresse, ou

(iii) d’affecter la capacité du conducteur à

utiliser le véhicule de façon sécuritaire.

Dans certains cas, il peut être impossible

d’installer ce produit en raison du type de

véhicule ou de la forme de l’intérieur du

véhicule.

ATTENTION

Pioneer ne recommande pas d’installer ce

produit soi-même. Ce produit est conçu

pour être installé uniquement par des

professionnels. Il est recommandé de

confier la configuration et l’installation de

ce produit au personnel de service de

Pioneer uniquement, qui a reçu une

formation spéciale et a l’expérience des

appareils électroniques mobiles. NE

RÉPAREZ JAMAIS CE PRODUIT VOUS-

MÊME. En installant ou réparant vous-

même ce produit et ses câbles de

connexion, vous vous exposez à un risque

de décharge électrique ou d’autres

dangers et vous risquez de causer des

dommages non couverts par la garantie à

ce produit.

PRÉCAUTION

• Fixez tous les câbles avec des serre-câbles

ou du ruban isolant. Ne laissez aucun fil

nu exposé.

• Ne connectez pas le fil jaune de ce

produit directement à la batterie du

véhicule. Si le fil est directement

connecté à la batterie, les vibrations du

moteur peuvent éventuellement

endommager l’isolation au point où le fil

passe de l’habitacle au compartiment

moteur. Si l’isolation du fil jaune s’use au

contact des pièces métalliques, cela peut

causer un court-circuit très dangereux.

• Il est extrêmement dangereux de laisser

les câbles s’enrouler autour de la colonne

de direction ou du levier de vitesse.

Assurez-vous d’installer ce produit, ses

câbles et ses fils à l’écart, de sorte qu’ils ne

gênent pas la conduite.

• Assurez-vous que les câbles et fils ne

gêneront pas ou ne seront pas coincés

par les pièces mobiles du véhicule, et tout

particulièrement le volant de direction, le

levier de vitesse, le frein de

stationnement, les rails de siège

coulissant, les portières ou toute

commande du véhicule.

• Ne posez pas les fils à des emplacements

exposés à des températures élevées. La

surchauffe de l’isolation peut

endommager les fils, entraînant un court-

circuit ou un problème de

fonctionnement et des dommages

permanents au produit.

• Ne raccourcissez aucun fil. Autrement, le

circuit de protection (porte-fusible,

résistance de protection ou filtre, etc.)

risque de ne pas bien fonctionner.

Importantes mesures

de protection

Précautions à prendre

avant de connecter le

système

3Fr

Français

• N’alimentez jamais d’autres produits

électroniques en coupant l’isolation du fil

d’alimentation de ce produit pour y

connecter un autre fil. La capacité du fil

serait dépassée, entraînant une

surchauffe.

• N’utilisez cet appareil qu’avec une

batterie 12 volts avec masse négative.

Autrement, il y a risque d’incendie ou de

problème de fonctionnement.

• Pour éviter de court-circuiter le système

électrique, pensez à déconnecter le câble

de batterie (–) avant l’installation.

ATTENTION

• Lorsque la sortie de haut-parleur est

utilisée par 4 canaux, utilisez des haut-

parleurs de plus de 50 W (Puissance

d’entrée maximale) et de 4 Ω à 8 Ω (valeur

d’impédance). N’utilisez pas de haut-

parleurs de 1 Ω à 3 Ω avec cet appareil.

• Lorsque la sortie de haut-parleur arrière

est utilisée par un caisson d’extrêmes

graves de 2 Ω, utilisez des haut-parleurs

de plus de 70 W (Puissance d’entrée

maximale).

*Veuillez vous reporter aux connexions

pour connaître la méthode de connexion.

• Le fil noir est le fil de masse. Lors de

l’installation de cet appareil ou d’un

amplificateur de puissance (vendu

séparément), pensez à connecter d’abord

le fil de masse. Assurez-vous que le fil de

masse est bien connecté à une partie

métallique de la carrosserie du véhicule.

Le fil de masse de l’amplificateur de

puissance et celui de cet appareil ou de

tout autre dispositif doivent être

connectés au véhicule séparément, avec

des vis différentes. Si la vis du fil de masse

se desserre ou tombe, il y a risque

d’incendie et de génération de fumée ou

de problème de fonctionnement.

• Lors du remplacement du fusible,

assurez-vous d’utiliser un fusible de la

capacité nominale indiquée sur ce

produit.

• Lors de la déconnexion d’un connecteur,

tirez sur le connecteur lui-même. Ne tirez

pas sur le fil, car vous pourriez le détacher

du connecteur.

• Ce produit ne peut pas être installé dans

un véhicule dont le commutateur

d’allumage n’a pas de position ACC

(accessoire).

• Pour éviter le court-circuitage, recouvrez

le fil déconnecté de ruban isolant. Il est

tout particulièrement important d’isoler

Avant d’installer ce

produit

Pour éviter les

dommages

Fil de masse

AMPLIFICATEUR DE

PUISSANCE

Autres appareils

(autres appareils

électroniques dans

le véhicule)

Pièces métalliques

de la carrosserie du

véhicule

*1 Non fourni avec cet appareil

Position ACC

Sans position ACC

tous les fils de haut-parleur non utilisés,

car ils peuvent causer un court-circuit s’ils

sont dénudés.

• Pour connecter un amplificateur de

puissance ou d’autres dispositifs à ce

produit, reportez-vous au mode d’emploi

du produit à connecter.

• Le symbole graphique placé sur le

produit signifie « courant continu ».

• Lors de la mise du commutateur

d’allumage en position de marche (ACC

ON), un signal de commande est envoyé

par le fil bleu/blanc. Connectez-le à la

borne de commande à distance de

système de l’amplificateur de puissance,

à la borne de commande de relais de

l’antenne de véhicule ou à la borne de

commande de puissance de

l’amplificateur d’antenne (max. 300 mA,

12 V c.c.). Le signal de commande est

envoyé par le fil bleu/blanc même si la

source audio est éteinte.

Important

Lorsque ce produit est en mode [Power

OFF], le signal de commande est

également désactivé. Si le mode [Power

OFF] est annulé, le signal de commande est

émis de nouveau et l’antenne se déploie

avec la fonction d’antenne automatique (si

l’antenne est utilisée). Veillez à ce que

l’antenne déployée n’entre pas en contact

avec des obstacles.

▶DMH-WT8600NEX/DMH-

WT7600NEX/DMH-WT76NEX/DMH-

WC6600NEX/DMH-WC5700NEX

▶DMH-W4660NEX/DMH-W4600NEX

Antenne GPS 3,55 m

Microphone 3 m

Entrée d’adaptateur iDatalink ou Metra

Remarque sur le fil

bleu/blanc

Panneau arrière

(bornes principales)

4Fr

Reportez-vous au mode d’emploi de

l’adaptateur iDataLink ou Metra (vendu

séparément).

Connecteur de câble de moniteur*

Connectez à l’écran LCD.

Prise d’antenne

Ce produit

Source de sortie préamplifiée

Alimentation

Fusible (10A)

Entrée de télécommande filaire

Il est possible de connecter un

adaptateur pour télécommande filaire

(vendu séparément).

SiriusXM Connect Vehicle Tuner

Reportez-vous au mode d’emploi de

SiriusXM Connect Vehicle Tuner (vendu

séparément).

* Le câble de moniteur et le connecteur se

trouvent dans le panneau avant. (DMH-

WT8600NEX, DMH-WT7600NEX, DMH-

WT76NEX)

REMARQUES

• Avant d’utiliser et/ou de connecter

l’adaptateur iDatalink Maestro (vendu

séparément), vous devez d’abord activer

le module Maestro avec le micrologiciel

approprié pour le véhicule et l’appareil

principal. Vous pouvez trouver le numéro

d’appareil qui est requis pour l’activation

à ces endroits (reportez-vous au Mode

d’emploi) :

– L’étiquette sur l’emballage de ce produit

–L’étiquette sur ce produit

–L’écran [Info sur le micrologiciel]

• Lorsque l’adaptateur iDatalink Maestro

est connecté, utilisez le microphone de

cet appareil pour effectuer les opérations

vocales avec Apple CarPlay, Android Auto

ou Amazon Alexa.

ATTENTION

UNE CONNEXION INAPPROPRIÉE

RISQUE D’ENTRAÎNER DES DOMMAGES

OU BLESSURES GRAVES, INCLUANT UNE

DÉCHARGE ÉLECTRIQUE, ET DES

INTERFÉRENCES AVEC LE

FONCTIONNEMENT DU SYSTÈME DE

FREINAGE ANTIBLOCAGE, LA BOÎTE DE

VITESSE AUTOMATIQUE ET LES

INDICATIONS DU COMPTEUR DE

VITESSE DU VÉHICULE.

Vers la source d’alimentation

Cordon d’alimentation

Jaune

Vers une borne alimentée quelle que

soit la position du commutateur

d’allumage.

Rouge

Vers une borne électrique commandée

par l’activation et la désactivation du

commutateur d’allumage (12 V c.c.)

Orange/blanc

Vers la borne de commutateur

d’éclairage.

Noir (masse)

Cordon d’alimentation

Vers la carrosserie (partie métallique) du

véhicule.

Violet/blanc

Des deux fils connectés à la lampe

arrière, connectez celui dont la tension

change lorsque le levier de vitesse est

sur la position REVERSE (R). Cette

connexion permet à l’appareil de

détecter si le véhicule se déplace vers

l’avant ou vers l’arrière.

Rose

Entrée du signal de vitesse du véhicule

Bleu/blanc

Connectez-le à la borne de commande

de système de l’amplificateur de

puissance (max. 300 mA, 12 V c.c.).

Vert pâle

Ce fil sert à détecter si le frein de

stationnement est engagé ou non. Ce fil

doit être connecté du côté alimentation

du commutateur de frein de

stationnement.

Si cette connexion est omise ou

incorrecte, certaines fonctions de ce

produit ne seront pas disponibles.

Côté alimentation

Commutateur de frein de

stationnement

Côté masse

REMARQUE

La position du circuit de détection de

vitesse et la position du commutateur de

frein de stationnement peuvent varier en

fonction du modèle du véhicule. Pour plus

de détails, consultez votre détaillant

Pioneer agréé ou un installateur

professionnel.

Effectuez ces connexions si vous utilisez un

caisson d’extrêmes graves sans

l’amplificateur en option.

Vers la source d’alimentation

Cordon d’alimentation

Gauche

Droite

Haut-parleur avant (STD) ou haut-

parleur de sons aigus (NW)

Haut-parleur arrière (STD) ou haut-

parleur de sons moyens (NW)

Blanc

Blanc/noir

Gris

Gris/noir

Vert

Vert/noir

Fils de haut-parleurs

La page charge ...

Pioneer DMH-W4660NEX Guide de démarrage rapide

Marque: Pioneer

Modèle: DMH-W4660NEX

Taper: Guide de démarrage rapide

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Pioneer DMH-W4660NEX Quick start guide
español: Pioneer DMH-W4660NEX Guía de inicio rápido

Documents connexes

Autres documents

Idatalink KIT-WJL1 Guide d'installation