Day-Brite CFI FluxPanel LED Install Instructions
- Catégorie
- Câbles de signal
- Taper
- Install Instructions
www.day-brite.com www.cfi-ligh�ng.com2/5/2019 page 1
443581588890
FLUX PANEL
FLUX PANEL SUSPENSION BRACKET
Figure 1.1
Figure 1.3
1. Unpack suspension kit and make sure all parts are
accounted for. (2 suspension brackets, 12 screws, 2
cross cables, and cable gripper)
2. Unscrew (6) T-grid hooks, Figure 1.1, and discard
each hook including the (2) screws from each.
3. Place the (2) suspension brackets along
the length of the side aligning the holes.
4. Screw the (12) screws included in the kit
in the empty holes. Figure 1.2
5. Attach (2) cross cables and
cable gripper to both ends of the
luminaire by inserting the cross
cable toggles through hanger
holes on the suspension bracket
previously installed. Figure1.3
Figure 1.2
Cable Grippers
Retention Screw
Cable Toggles
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN
OR SERVICE PERSONNEL
ATTENTION : L'INSTALLATION ET L'ENTRETIEN DE CE PRODUIT DOIVENT ÊTRE EFFECTUÉS PAR UN ÉLECTRICIEN OU UN
MEMBRE DU PERSONNEL QUALIFlÉ.
6. Lock cable grippers in place midway between hanging clips by inserting the retention screw
into the bottom of the gripper and tightening loosely. Luminaire can be leveled once it is in
place by sliding cross cables to appropriate balance point. Once luminaire is leveled tighten
retention screw to lock grippers in place.
CAUTION: Elect
rical luminaires are designed for permanent installation in ordinary (Non-Hazardous) locations in accordance with the National Electrical Code and
all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact
with combustible materials can cause fire and personal contact can cause severe burns.
ATTENTION: Ce luminaire a été conçu pour une installation permanente dans un emplacement régulier (non dangereux) et en conformité avec le Code électrique
canadien et codes locaux applicables. Ne jamais installer dans un endroit où la ventilation est limitée au dans des boitiers où la température ambiante est très
élevée. La lampe et le luminaire fonctionnent à des témperatures élevées, un contact avec des matériaux combustibles peut engendrer un incendie et un contact
corporel peut causer de séverès brûlures.
2/5/19 page 2
443581588890
FLUX PANEL
FLUX PANEL SUSPENSION BRACKET
POWER-FEED END OF LUMINAIRE
STEP 1:
Attach bracket and stud to customer supplied junction box.
Attach green ground screw to bracket.
STEP 2:
Support the luminaire approximately 2' below mounting surface.
Once luminaire is supported pass end of power cord through
power feed hole in canopy.
Power Cord
STEP 3:
Make wiring connections to cord leads.
STEP 4:
Insert cable into two piece coupler ensuring that cable terminal
sits in coupler. Slide power feed canopy over stud and screw
coupler to stud. Use outer coupler ring to lock canopy to junction
box.
STEP 5:
Attach strain relief to cord and insert into canopy opening. Allow
approximately 6" of cord above strain relief.
NOTE: For splice inspection the canopy can be dropped away
from junction box by loosening outer coupler ring and dropping
canopy away from ceiling.
ATTACHMENT OF CABLES TO CROSS CABLE GRIPPERS
Ground Screw
Bracket
Threaded Stud
Canopy
Strain Relief
To Fixture
Cable
Coupler
www.day-brite.com www.cfi-lighting.com
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN
OR SERVICE PERSONNEL
ATTENTION : L'INSTALLATION ET L'ENTRETIEN DE CE PRODUIT DOIVENT ÊTRE EFFECTUÉS PAR UN ÉLECTRICIEN OU UN
MEMBRE DU PERSONNEL QUALIFlÉ.
CAUTION: Electrical luminaires are designed for permanent installation in ordinary (Non-Hazardous) locations in accordance with the National Electrical Code and all
applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact with combustible
materials can cause fire and personal contact can cause severe burns.
-
1
-
2
Day-Brite CFI FluxPanel LED Install Instructions
- Catégorie
- Câbles de signal
- Taper
- Install Instructions
dans d''autres langues
- English: Day-Brite CFI FluxPanel LED