DeWalt DWE4120N Manuel utilisateur

DWE4100, DWE4120, DWE4120N

Small Angle Grinder

Petite meuleuse angulaire

Esmeriladora angular pequeña

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term "power tool" in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

1

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

English

2

SAFETY INSTRUCTIONS FOR

ALL OPERATIONS

Safety Warnings Common for Grinding,

Sanding, Wire Brushing, Polishing or

Abrasive, Cutting-Off Operations

a) This power tool is intended to function as a grinder,

sander, wire brush, polisher or cut-off tool. Read

all safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure to

follow all instructions listed below may result in electric shock,

fire and/or serious injury.

b) Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

c) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can break

and fly apart.

d) The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded or

controlled.

e) The arbor size of wheels, flanges, backing pads or any

other accessory must properly fit the spindle of the

power tool. Accessories with arbor holes that do not match

the mounting hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

f) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing

an accessory, position yourself and bystanders away

from the plane of the rotating accessory and run the

power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this test

time.

g) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments. The eye

protection must be capable of stopping flying debris generated

by various operations. The dust mask or respirator must be

capable of filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may cause hearing

loss.

h) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

i) Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a "live" wire may make exposed

metal parts of the power tool "live" and shock the operator.

j) Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your hand or

arm may be pulled into the spinning accessory.

English

3

k) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab

the surface and pull the power tool out of your control.

l) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

m) Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical hazards.

n) Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

o) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in electrocution

or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by taking

proper precautions as given below:

a) Maintain a firm grip on the power tool and position your

body and arm to allow you to resist kickback forces.

Always use auxiliary handle, if provided, for maximum

control over kickback or torque reaction during start up.

The operator can control torque reaction or kickback forces, if

proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool

in direction opposite to the wheel’s movement at the point of

snagging.

d) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory. Corners,

sharp edges or bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss of

control.

Safety Warnings Speciﬁ c for Grinding and

Abrasive Cutting-Off Operations

a) Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

b) The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator. The

guard helps to protect operator from broken wheel fragments,

accidental contact with wheel, and sparks that could ignite

clothing.

English

4

c) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral grinding,

side forces applied to these wheels may cause them to shatter.

d) Always use undamaged wheel flanges that are of correct

size and shape for your selected wheel. Proper wheel

flanges support the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be different from

grinding wheel flanges.

e) Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the

higher speed of a smaller tool and may burst.

Additional Safety Warnings Speciﬁ c for

Abrasive Cutting-Off Operations

a) Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut and

the possibility of kickback or wheel breakage.

b) Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation,

is moving away from your body, the possible kickback may

propel the spinning wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

reason, switch off the power tool and hold the power

tool motionless until the wheel comes to a complete

stop. Never attempt to remove the cut-off wheel from

the cut while the wheel is in motion otherwise kickback

may occur. Investigate and take corrective action to eliminate

the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully reenter the

cut. The wheel may bind, walk up or kickback if the power tool

is restarted in the workpiece.

e) Support panels or any oversized workpiece to minimize

the risk of wheel pinching and kickback. Large workpieces

tend to sag under their own weight. Supports must be placed

under the workpiece near the line of cut and near the edge of

the workpiece on both sides of the wheel.

f) Use extra caution when making a "pocket cut" into

existing walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects that can

cause kickback.

Safety Warnings Speciﬁ c for Sanding

Operations

a) Do not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when selecting

sanding paper. Larger sanding paper extending beyond the

sanding pad presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety Warnings Speciﬁ c for Polishing

Operations:

a) Do not allow any loose portion of the polishing bonnet

or its attachment strings to spin freely. Tuck away or trim

any loose attachment strings. Loose and spinning attachment

strings can entangle your fingers or snag on the workpiece.

English

5

Safety Warnings Speciﬁ c for Wire

Brushing Operations

a) Be aware that wire bristles are thrown by the brush even

during ordinary operation. Do not overstress the wires

by applying excessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing,

do not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in diameter

due to work load and centrifugal forces.

Additional Safety Rules for Grinders

WARNING: The grinding wheel or accessory may loosen

during coast-down of the tool when shut off. If grinding wheel or

accessory loosens, it may dismount from the machine and may

cause serious personal injury.

• Use of accessories not specified in this manual is not

recommended and may be hazardous. Use of power boosters

that would cause the tool to be driven at speeds greater than its

rated speed constitutes misuse.

• Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss of

control.

• Avoid bouncing the wheel or giving it rough treatment. If this

occurs, stop the tool and inspect the wheel for cracks or flaws.

• Always handle and store wheels in a careful manner.

• Never cut into area that may contain electrical wiring or

piping. Serious injury may result.

• Do not operate this tool for long periods of time. Vibration

caused by the operating action of this tool may cause permanent

injury to fingers, hands, and arms. Use gloves to provide extra

cushion, take frequent rest periods, and limit daily time of use.

• Do not use Type 11 (flaring cup) wheels on this tool. Using

inappropriate accessories can result in injury.

• Always use side handle. Tighten the handle securely. The

side handle should always be used to maintain control of the tool

at all times.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts

Total Length of Cord

in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More

Than

Not More

Than

AWG

0 6 18 16 16 14

610 1816 1412

10 12 16 16 14 12

12 16 14 12 Not Recommended

English

6

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appropriate

for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ................... volts A ......................amperes

Hz ................. hertz W ..................... watts

min ............... minutes or AC ..........alternating

or DC ... direct current current

................. Class I Construction or AC/DC ...alternating or

.....................

(grounded) direct current

................. Class II Construction

n

o ....................no load

(double insulated) speed

…/min ........... per minute

n ......................rated speed

BPM .............beats per minute

.....................earthing

IPM ...............impacts per minute terminal

RPM ............. revolutions per

..................... safety alert

minute symbol

sfpm .............surface feet per minute

SAVE THESE INSTRUCTIONS FOR

FUTUREUSE

English

7

Motor

Be sure your power supply agrees with the nameplate marking.

Voltage decrease of more than 10% will cause loss of power and

overheating. D

EWALT tools are factory tested; if this tool does not

operate, check power supply.

COMPONENTS (Fig. 1, 6)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

A. Spindle lock button

B. Spindle

C. Side handle

D. Backing flange

E. Threaded clamp nut

F. Guard

G. Slider switch

H. Paddle switch

I. Lock on Button

J. Lock off lever (Fig. 6)

K. Guard release lever

INTENDED USE

This grinder is designed for professional grinder, sander, wire brush or

cut-off applications.

DO NOT use under wet conditions or in presence of flammable

liquids or gases.

This grinder is a professional power tool. DO NOT let children come

into contact with the tool. Supervision is required when inexperienced

operators use this tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off and

disconnect it from power source before installing and removing

accessories, before adjusting or when making repairs. An

accidental start-up can cause injury.

FIG. 1

E

D

DWE4100

DWE4120

DWE4120N

G

I

H

A

F

C

K

B

English

8

ATTACHING SIDE HANDLE (FIG. 2)

The side handle (C) can be fitted to either side of

C

FIG. 2

the gear case in the threaded holes, as shown.

Before using the tool, check that the handle is

tightened se cure ly. Use a wrench to firmly

tighten the side handle.

Rotating the Gear Case

(Fig. 3)

1. Remove the four corner screws

FIG. 3

90˚

attaching the gear case to motor

housing.

2. Without separating the gear case from

motor housing, rotate the gear case

head to desired position.

NOTE: If the gear case and motor housing become separated

by more than 1/8" (3.17 mm), the tool must be serviced and

re-assembled by a D

EWALT service center. Failure to have the tool

serviced may cause brush, motor and bearing failure.

3. Reinstall screws to attach the gear case to the motor housing.

Tighten screws to 18 in.-lbs. torque. Overtightening could cause

screws to strip.

4-1/2" (114.3 mm) Grinding Wheels

Type 27 guard

backing flange

threaded clamp nut

Type 27 depressed

center wheel

Type 27 hubbed wheel

Type 27 guard

Wire Wheels

3" (76.2 mm)

wire cup brush

Type 27 guard

4" (101.6 mm) wire wheel

Type 27 guard

English

9

Use only the accessories shown on pages 9–10 of this manual.

Accessory ratings must be above listed minimum wheel speed as

shown on tool nameplate.

Mounting Guard

CAUTION: Guards must be used with all grinding wheels,

cutting wheels, sanding flap discs, wire brushes, and wire

wheels. The tool may be used without a guard only when sanding

with conventional sanding discs. A Type 27 guard (intended for use

with depressed center grinding wheels [Type 27 and Type29], sanding

flap discs, wire wheels and wire cup brushes) is available at extra cost

Accessories and Attachments

It is important to choose the correct guards, backing pads and flanges

to use with grinder accessories. See pages 9–10 for information on

choosing the correct accessories.

WARNING: Accessories must be rated for at least the speed

recom mended on the tool warning label. Wheels and other

accessories running over rated accessory speed may burst and

cause injury. Threaded accessories must have a 5/8"–11 hub. Every

unthreaded accessory must have a 7/8" arbor hole. If it does not, it

may have been designed for a circular saw and should not be used.

4-1/2" (114.3 mm) Cutting Wheels

Sanding Discs

4-1/2" (114.3 mm) Sanding Flap

Discs

Type 1 guard

backing flange

abrasive cutting wheel

clamp nut

Type 1 guard

backing flange

diamond cutting wheel

clamp nut

rubber backing pad

sanding disc

threaded clamp nut

hubbed sanding

flap disc

Type 27 guard

backing flange

non-hubbed sanding

flap disc

threaded clamp nut

Type 27 guard

English

10

from your local dealer or authorized service center. Grinding and

cutting with wheels other than Type 27 and 29 require different

accessory guards not included with tool. A Type 1 guard is provided

for use with the Type 1 wheel. Mounting instructions for accessory

guards are shown below and are also included in the accessory

package.

MOUNTING AND REMOVING (TYPE 27)

ONE-TOUCH™ GUARD (FIG. 4, 5)

NOTE: If your grinder is supplied with a

L

K

FIG. 4

N

M

keyless ONE TOUCH™ guard, ensure the

screw, lever and spring are fitted correctly

before mounting the guard.

1. Press the guard release lever (K).

2. While holding the guard release lever open,

align the lugs (L) on the guard with the

slots on the gear case (M).

3. Keeping the guard release lever open, push the guard down until

the guard lugs engage and rotate them in the groove on the gear

case hub. Release the guard release lever.

4. With the spindle facing the operator, rotate

FIG. 5

the guard clockwise into the desired

working position. The guard body should

be positioned between the spindle and

the operator to provide maximum operator

protection.

5. For easy adjustment, the guard can be

rotated in the clockwise direction. NOTE:

The guard release lever should snap into

one of the alignment holes (N) on the

guard collar. This insures that the guard is secure. The guard can

be repositioned the opposite direction by depressing the guard

release lever.

6. To remove the guard, follow steps 1–3 of these instructions in

reverse.

NOTE: Edge grinding and cutting can be performed with Type 27

wheels designed and specified for this purpose; 1/4" (6.35mm) thick

wheels are designed for surface grinding while 1/8" (3.17 mm) wheels

are designed for edge grinding. Cutting can also be performed by

using a Type 1 wheel and a Type 1 guard.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and

disconnect it from power source before installing and removing

accessories, before adjusting or when making repairs. An

accidental start-up can cause injury.

Guards and Flanges

It is important to choose the correct guards and flanges to use with

the grinder accessories. See page 9–10 and this page for the correct

accessories.

NOTE: Edge grinding and cutting can be performed with Type 27

wheels designed and specified for this purpose.

WARNING: Accessories must be rated for at least the speed

recom mended on the tool warning label. Wheels and other

accessories running over rated accessory speed may burst and

cause injury. Every unthreaded accessory must have a 7/8" arbor

hole. If it does not, it may have been designed for a circular saw and

should not be used. Use only the accessories shown on pages 9–10.

Accessory ratings must be above listed minimum wheel speed as

shown on tool nameplate.

Switches

CAUTION: Hold the side handle and body of the tool firmly to

maintain control of the tool at start up and during use and until the

wheel or accessory stops rotating. Make sure the wheel has come to

a complete stop be fore laying the tool down.

English

11

NOTE: To reduce unexpected tool movement, do not switch the

tool on or off while under load conditions. Allow the grinder to run

up to full speed before touching the work surface. Lift the tool from

the surface before turning the tool off. Allow the tool to stop rotating

before putting it down.

PADDLE SWITCH (DWE4120, DWE4120N) (FIG. 6)

CAUTION: Before connecting the tool to a power source depress

and release the paddle switch (H) to ensure that the switch is off..

Depress and release the paddle switch as described above after any

interruption in power supply to the tool, such as the activation of a

ground fault interrupter, throwing of a circuit breaker, accidental

unplugging, or power failure.

To turn the tool on, push the lock-off

H

J

FIG. 6

lever (J) toward the back of the tool,

then depress the paddle switch (H).

The tool will run while the switch is

depressed. Turn the tool off by

releasing the paddle switch.

WARNING: Do not disable the lock-off lever. If the lock-off lever is

disabled, the tool may start unexpectedly when it is laid down.

SLIDER SWITCH (FIG. 7)

WARNING: Before connecting the

G

FIG. 7

tool to a power supply, be sure the

slider switch is in the off position by

pressing the rear part of the switch

and releasing. Ensure the slider switch

is in the off position as described

above after any interruption in power

supply to the tool, such as the activation of a ground fault interrupter,

throwing of a circuit breaker, accidental unplugging, or power failure.

If the slider switch is locked on when the power is connected, the tool

will start unexpectedly.

To start the tool, slide the ON/OFF slider switch (G) toward the front of

the tool. To stop the tool, release the ON/OFF slider switch.

For continuous operation, slide the switch toward the front of the

tool and press the forward part of the switch inward. To stop the tool

while operating in continuous mode, press the rear part of the slider

switch and release.

LOCK-ON BUTTON (DWE4120) (FIG. 8)

The lock-on button (I) offers increased comfort in extended use

applications. To lock the tool on, push the

I

H

J

FIG. 8

lock-off lever (J) toward the back of the

tool then depress the paddle switch (H).

With the tool running, depress the lock-

on button (I). The tool will continue to run

after the paddle switch is released. To

unlock the tool, depress and release the

paddle switch. This will cause the tool to

stop.

CAUTION: Allow the tool to reach full speed before touching tool

to the work surface. Lift the tool from the work surface before turning

the tool off.

SPINDLE LOCK (FIG. 9)

The spindle lock button (A) is provided to

A

FIG. 9

prevent the spindle from rotating when

installing or removing wheels. Operate the

spindle lock only when the tool is turned off,

unplugged from the power supply, and has

come to a complete stop. Do not engage

the spindle lock button while the tool is

operating because damage to the tool will result. To engage the lock,

depress the spindle lock button and rotate the spindle until you are

unable to rotate the spindle further.

English

12

Mounting and Using Depressed Center

Grinding Wheels and Sanding Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS (FIG. 10)

Hubbed wheels install directly on the 5/8"–11

1/4" WHEELS

(6.35 mm)

Backing Flange

Clamp Nut

1/8" WHEELS

(3.17mm)

Backing Flange

Clamp Nut

D

B

E

FIG. 10

threaded spindle. Thread of accessory must

match thread of spindle.

1. Remove backing flange (D) by pulling

away from the tool.

2. Thread the wheel on the spindle (B) by

hand.

3. Depress the spindle lock button and use

a wrench to tighten the hub of the wheel.

4. Reverse the above procedure to remove

the wheel.

NOTICE: Failure to properly seat the wheel

before turning the tool on may result in

damage to the tool or the wheel.

MOUNTING NON-HUBBED WHEELS

(FIG. 10)

Depressed center Type 27 grinding wheels

must be used with included flanges. Refer

to Accessories and Attachments for more

information.

1. Install the backing flange (D) on spindle (B)

with the raised section (pilot) against the

wheel. Be sure the backing flange recess

is seated onto the flats of the spindle by

pushing and twisting the flange before

placing wheel.

2. Place wheel against the backing flange, centering the wheel on

the raised section (pilot) of the backing flange.

3. While depressing the spindle lock button, thread the clamp

nut(E) on spindle. If the wheel you are installing is more than 1/8"

(3.17mm) thick, place the threaded clamp nut on the spindle so

that the raised section (pilot) fits into the center of the wheel. If

the wheel you are installing is 1/8" (3.17mm) thick or less, place

the threaded clamp nut on the spindle so that the raised section

(pilot) is not against the wheel.

4. While depressing the spindle lock button, tighten the clamp nut

with a wrench.

5. To remove the wheel, depress the spindle lock button and loosen

the threaded clamp nut with a wrench.

NOTE: If the wheel spins after the clamp nut is tightened, check the

orientation of the threaded clamp nut. If a thin wheel is installed with

the pilot on the clamp nut against the wheel, it will spin because the

height of the pilot prevents the clamp nut from holding the wheel.

SURFACE GRINDING WITH GRINDING WHEELS (FIG. 11)

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to the work surface, allowing the tool

to operate at high speed. Grinding rate is greatest when the tool

operates at high speed.

3. Maintain a 20˚ to 30˚ angle between the

20˚–30˚

FIG. 11

tool and work surface.

4. Continuously move the tool in a forward

and back motion to avoid creating

gouges in the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

English

13

EDGE GRINDING WITH GRINDING WHEELS (FIG. 12)

WARNING: Wheels used for cutting and edge grinding may break

if they bend or twist while the tool is being used to do cut-off work or

deep grinding. To reduce the risk of serious injury, limit the use of

these wheels with a standard Type 27 guard to shallow cutting and

notching (less than 1/2" in depth). The open side of the guard must

be positioned away from the operator. For deeper cutting with a

Type1 cut-off wheel, use a closed, Type 1 guard. See the chart on

pages 9–10 for more information. Type 1 guards are available at

extra cost from your local dealer or authorized service center.

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to the work

FIG. 12

surface, allowing the tool to operate at

high speed. Grinding rate is greatest

when the tool operates at high speed.

3. Position yourself so that the open-

underside of the wheel is facing away

from you.

4. Once a cut is begun and a notch is

established in the workpiece, do not

change the angle of the cut. Changing

the angle will cause the wheel to bend

and may cause wheel breakage. Edge

grinding wheels are not designed to

withstand side pressures caused by

bending.

5. Remove the tool from the work surface before turning the tool off.

Allow the tool to stop rotating before laying it down.

WARNING: Do not use edge grinding/cutting wheels for surface

grinding applications because these wheels are not designed for side

pressures encountered with surface grinding. Wheel breakage and

injury may result.

SURFACE FINISHING WITH SANDING FLAP DISCS (FIG. 13)

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to work

5˚–10˚

FIG. 13

surface, allowing the tool to operate

at high speed. Sanding rate is

greatest when the tool operates at

high speed.

3. Maintain a 5˚ to 10˚ angle between the tool and work surface.

4. Continuously move the tool in a forward and back motion to

avoid creating gouges in the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

MOUNTING SANDING BACKING PADS (FIG. 14)

WARNING: Proper guard must be

E

O

P

FIG. 14

reinstalled for grinding wheel, sanding flap

disc, wire brush or wire wheel applications

after sanding applications are complete.

1. Place or appropriately thread backing

pad (O) on the spindle.

2. Place the sanding disc (P) on the

backing pad.

3. While depressing spindle lock, thread

the clamp nut (E) on spindle, piloting

the raised hub on the clamp nut into

the center of san ding disc and backing

pad.

English

14

4. Tighten the clamp nut by hand. Then depress the spindle lock

button while turning the sanding disc until the sanding disc and

clamp nut are snug.

5. To remove the wheel, grasp and turn the backing pad and

sanding pad while depressing the spindle lock button.

USING SANDING BACKING PADS (FIG. 15)

Choose the proper grit sandpaper for your application. Sandpaper

is available in various grits. Coarse grits yield faster material removal

rates and a rougher finish. Finer grits yield slower material removal

and a smoother finish.

Begin with coarse grit discs for fast, rough material removal. Move

to a medium grit paper and finish with a fine grit disc for optimal

finish.

Coarse 16 – 30 grit

Medium 36 – 80 grit

Fine Finishing 100 – 120 grit

Very Fine Finishing 150 – 180 grit

1. Allow the tool to reach full speed before touching tool to the work

surface.

2. Apply minimum pressure to work

5˚–15˚

FIG. 15

surface, allowing the tool to operate at

high speed. Sanding rate is greatest

when the tool operates at high speed.

3. Maintain a 5˚ to 15˚ angle between the

tool and work surface. The san ding

disc should contact approximately

one inch of work surface.

4. Move the tool constantly in a straight line to prevent burning and

swirling of work surface. Allowing the tool to rest on the work

surface without moving, or moving the tool in a circular motion

causes burning and swirling marks on the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the tool to stop rotating before laying it down.

Mounting and Using Wire Brushes

andWire Wheels

Wire cup brushes or wire wheels screw directly on the grinder

spindle without the use of flanges. Use only wire brushes or wheels

provided with a 5/8"–11 threaded hub. A Type 27 guard is required

when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes

and wheels. They can become sharp.

CAUTION: Wheel or brush must not touch guard when mounted

or while in use. Undetectable damage could occur to the accessory,

causing wires to fragment from accessory wheel or cup.

MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS

1. Thread the wheel on the spindle by hand.

2. Depress spindle lock button and use a wrench on the hub of the

wire wheel or brush to tighten the wheel.

3. To remove the wheel, reverse the above procedure.

NOTICE: Failure to properly seat the wheel hub before turning the

tool on may result in damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS (FIG 16, 17)

Wire wheels and brushes can be used for removing rust, scale and

paint, and for smoothing irregular surfaces.

English

15

1. Allow the tool to reach full speed before

5˚–10˚

FIG. 16

touching the tool to the work surface.

2. Apply minimum pressure to work surface,

allowing the tool to operate at high

speed. Material removal rate is greatest

when the tool operates at high speed.

3. Maintain a 5˚ to 10˚ angle between the tool and work surface for

wire cup brushes.

4. Maintain contact between the edge of the wheel and the work

surface with wire wheels.

5. Continuously move the tool in a forward and

FIG. 17

back motion to avoid creating gouges in the

work surface. Allowing the tool to rest on the

work surface without moving, or moving the

tool in a circular motion causes burning and

swirling marks on the work surface.

6. Remove the tool from the work surface before turning the tool off.

Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a

sudden sharp movement of grinder may be experienced.

Mounting and Using Cutting

(Type 1) Wheels

Cutting wheels include diamond wheels and abrasive discs. Abrasive

cutting wheels for metal and concrete use are available. Diamond

blades for concrete cutting can also be used.

WARNING: A closed, 2-sided cutting wheel guard is not included

with this tool but is re quired when using cutting wheels. Fail ure to use

proper flange and guard can re sult in injury resulting from wheel

breakage and wheel contact. See page 10 for more information.

MOUNTING CLOSED (TYPE 1) GUARD (FIG. 18 – 20)

WARNING: If present, the ONE TOUCH™ guard screw, lever and

spring must be removed before attempting to mount the closed

(Type1) guard. The removed parts must be retained and reinstalled

to use the ONE TOUCH™ guard. Noting the position of these parts

before disassembly will aid in reassembly.

1. Open the guard latch (Q). Align the

Q

L

M

FIG. 18

lugs (L) on the guard with the slots

(M) on the gear case.

2. Push the guard down until the guard

lug engages and rotates freely in

the groove on the gear case hub.

3. Rotate guard (F) into desired

working position. The guard body

should be positioned between the

spindle and the operator to provide

maximum operator protection.

4. Close the guard latch to secure the

F

FIG. 19

guard on the gear case cover. You

should be unable to rotate the guard by

hand when the latch is in closed

position. If rotation is possible, tighten

the adjusting screw (R) with clamp lever

in the closed position. Do not operate

grinder with a loose guard or clamp

lever in open position.

5. To remove the guard, open the guard latch, rotate the guard so

that the arrows are aligned and pull up on the guard.

English

16

NOTE: If, after a period of time the closed (Type 1)

R

FIG. 20

guard becomes loose, tighten the adjusting

screw (R) with the clamp lever in the closed

position.

NOTICE: Do not tighten adjusting screw with

clamp lever in open position. Undetectable

damage to guard or mounting hub may result.

CAUTION: If the guard cannot be tightened by the adjusting clamp,

do not use the tool. To reduce the risk of personal injury, take the tool

and guard to an authorized service center to repair or replace the

guard.

MOUNTING CUTTING WHEELS

CAUTION: Matching diameter threaded backing flange and clamp

nut (included with tool) must be used for cutting wheels.

1. Place the unthreaded backing flange on spindle with the raised

section (pilot) facing up. The raised section (pilot) on the backing

flange will be against the wheel when the wheel is installed.

2. Place the wheel on the backing flange, centering the wheel on the

raised section (pilot).

3. Install the threaded clamp nut with the raised section (pilot)

facing away from the wheel.

4. Depress the spindle lock button and tighten clamp nut with a

wrench.

5. To remove the wheel, grasp and turn while depressing the

spindle lock button.

USING CUTTING WHEELS (FIG. 21)

WARNING: Do not use edge grinding/cutting wheels for surface

grinding applications because these wheels are not designed for side

pressures encountered with surface grinding. Wheel breakage and

injury may result.

1. Allow tool to reach full speed before

FIG. 21

touching tool to work surface.

2. Apply minimum pressure to work

surface, allowing tool to operate at

high speed. Cutting rate is greatest

when the tool operates at high speed.

3. Once a cut is begun and a notch is

established in the workpiece, do not

change the angle of the cut. Changing

the angle will cause the wheel to bend

and may cause wheel breakage.

4. Remove the tool from work surface

before turning tool off. Allow the tool to

stop rotating before setting it down.

MAINTENANCE

WARNING: To reduce the risk of injury, turn unit off and

disconnect it from power source before installing and removing

accessories, before adjusting or when making repairs. An

accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

English

17

Accessories

WARNING: Since accessories, other than those offered by

D

EWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

EWALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at

extra cost from your local dealer or authorized service center. If you

need assistance in locating any accessory, please contact D

EWALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,

call 1-800-4-D

EWALT (1-800-433-9258) or visit our website: www.

D

EWALT.com.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement) should

be performed by a D

EWALT factory service center, a DEWALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others. This

warranty gives you specific legal rights and you may have other rights

which vary in certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

D

EWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

D

EWALT Power Tool, Laser, or Nailer for any reason, you can return

it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the

local company or see website for warranty information.

English

18

La page est en cours de chargement...

DeWalt DWE4120N Manuel utilisateur

DeWalt DWE4120N Manuel utilisateur

dans d''autres langues

Documents connexes