GE 10 DCB Manuel utilisateur

Cool Only: AJCH 08, 10 ACB
AJCH 10, 12  DCB
AJCQ 08, 10 ACB
AJCQ 10, 12  DCB
AJCS 06 LCB
AJCS 08, 10 ACB
AJCS 09, 10, 12 DCB
Heat/Cool: AJEH 12 DCB
AJES 06 LSB
AJES 08 ASB
AJES 09, 10, 12 DCB
AJES 10 DSB
Heat Pump: AJHS 08 ASB
AJHS 08, 10 DCB
Write the model and serial numbers here:
Model # __________________________
Serial #
____________________________
Find these numbers on a label on the front
of the base pan behind the front grille.
Air Conditioners
www.GEAppliances.com
Room

2

Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric

shock or personal injury.

■ Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

■ This air conditioner must be properly

installed in accordance with the

Installation Instructions before it is used.

■ Never unplug your air conditioner by

pulling on the power cord. Always grip

plug firmly and pull straight out from the

receptacle.

■ Repair or replace immediately all electric

service cords that have become frayed or

otherwise damaged. Do not use a cord

that shows cracks or abrasion damage

along its length or at either the plug or

connector end.

■ Turn the mode control OFF and unplug

your air conditioner before making any

repairs or cleaning.

NOTE: We strongly recommend that any

servicing be performed by a qualified

individual.

■ For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

■ All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants,

check with the company handling disposal

about what to do.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

For personal safety, this appliance must be

properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which

mates with a standard 3-prong (grounding)

wall outlet to minimize the possibility of

electric shock hazard from this appliance.

Have the wall outlet and circuit checked

by a qualified electrician to make sure the

outlet is properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The air conditioner should always be plugged

into its own individual electrical outlet which

has a voltage rating that matches the rating

plate.

This provides the best performance and also

prevents overloading house wiring circuits

which could cause a fire hazard from

overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support

3

www.GEAppliances.com

WARNING!

Because of potential safety hazards under

certain conditions, we strongly recommend

against the use of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14 gauge, 3-wire grounding type appliance

extension cord having a grounding type plug

and outlet and that the electrical rating of

the cord be 15 amperes (minimum) and

125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

USE OF EXTENSION CORDS—115-Volt models only

Because of potential safety hazards under

certain conditions, we strongly recommend

against the use of an adapter plug.

However, if you must use an adapter, where

local codes permit, a temporary connection

may be made to a properly grounded

2-prong wall outlet by use of a UL-listed

adapter available at most local hardware

stores.

The larger slot in the adapter must be

aligned with the larger slot in the wall

outlet to provide proper polarity in the

connection of the power cord.

When disconnecting the power cord from

the adapter, always hold the adapter in place

with one hand while pulling the power cord

plug with the other hand. If this is not done,

the adapter ground terminal is very likely to

break with repeated use.

If the adapter ground terminal breaks,

DO NOT USE the air conditioner until a

proper ground has been established.

Attaching the adapter ground terminal to a wall

outlet cover screw does not ground the appliance

unless the cover screw is metal, not insulated, and

the wall outlet is grounded through the house wiring.

You should have the circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

USE OF ADAPTER PLUGS—115-Volt models only

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Vent Control

The vent control is located behind the front grille on

the right side of the air discharge area. When set at

CLOSE, only the air inside the room will be circulated

and conditioned. When set at OPEN, some inside air is

exhausted outside.

To open or close the vent:

1. Remove the front grille.

2. Remove the vent card screw.

3. Remove vent card, turn it over and replace it by

locating rear hole in card over locating pin inside air

discharge and reattaching screw at front.

Horizontal louvers

on the front grille let

you control the air

direction up and

down.

Remove the front

grille to adjust the

vertical louvers

side-to-side to

direct the air

left or right.

Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support

5

Air Direction

Locating hole

www.GEAppliances.com

COOL MODE

Remote Control

1. Press COOL pad.

2. Press LOW, MED or HI pads to set desired fan speed.

3. Press the INCREASE ▲ / DECREASE ▼ pads to set the

desired temperature 60°F to 85°F in 1°F increments.

Control Panel

1. Press the MODE pad until the COOL indicator light is

lit and the LOW, MED or HI indicator light is lit for

the desired fan speed.

2. Press the INCREASE ▲ / DECREASE ▼ pads to set the

desired temperature 60°F to 85°F in 1°F increments.

A thermostat is used to maintain the room

temperature. The compressor will cycle on and off

to keep the room at the set level of comfort. Set the

thermostat at a lower number and the indoor air will

become cooler. Set the thermostat at a higher number

and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on

while set to COOL, it will take approximately 3 minutes for

the compressor to start and cooling to begin.

Cooling Descriptions

For Normal Cooling—Select the COOL mode and

HIGH or MED fan with a middle set temperature.

For Maximum Cooling—Select the COOL mode

and HIGH fan with a lower set temperature.

For Quieter & Nighttime Cooling—Select the COOL mode

and LOW fan with a middle set temperature.

NOTE: If you switch from a COOL setting to OFF or to

a fan setting, wait at least 3 minutes before switching back

to a COOL setting.

FAN MODE

Use the FAN mode to provide air circulation and

filtering without cooling. Since fan only settings do not

provide cooling, a temperature setting will not be

displayed.

Remote Control

Press FAN pad. Press LOW, MED or HI pads to set

desired fan speed.

Control Panel

Press the MODE pad until the FAN indicator light is lit

and the LOW, MED or HI indicator light is lit for the

desired fan speed.

Fan Switch

The fan switch is located behind the front grille on the

control box.

When set at CYCLE (down) the fan cycles on and off.

When set at CONT (continuous, up) the fan runs all the

time providing a more balanced temperature. The unit

is shipped in the CONT setting.

Screw hole

OPEN position

(Mesh end toward back)

CLOSE position

(Mesh end toward front)

Locating hole

Screw hole

The unit leaves the factory set at the CLOSE position.

Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions

6

Controls

Mode Control

HIGH COOL and LOW COOL provide cooling

with different fan speeds.

HIGH HEAT and LOW HEAT provide heating

with different fan speeds.

LOW FAN or HIGH FAN provides air

circulation and filtering without cooling

or heating.

NOTE: If you move the switch from a cool or heat

setting to OFF or to a fan setting, wait at least 3

minutes before switching back to a cool or heat

setting. A 3-minute delay is automatically provided

on the Heat/Cool and Heat Pump models.

Cooling/Heating Descriptions

For Normal Cooling or Heating—Select

HIGH COOL or HIGH HEAT with the

thermostat at mid point.

For Maximum Cooling—Select HIGH COOL

with the thermostat at maximum cool.

For Maximum Heating—Select HIGH HEAT

with the thermostat at maximum heat.

For Quieter & Nighttime Cooling—Select

LOW COOL with the thermostat at mid

point.

Temp Control

The temp control is used to maintain the

room temperature. The compressor will

cycle on and off to keep the room at the

same level of comfort. When you turn

the knob to COOLER (blue) the indoor air

will become cooler. Turn the knob to

WARMER (red) and the indoor air will

become warmer.

Heat Pump Models

When the outdoor temperature is lower

than 25°F., heat is provided by the electric

heater in the air conditioner instead of by

the heat pump.

NOTE: The electric resistance heater in the 115-volt

heat pump model operates during defrost when the

outdoor coil temperature is below 36°F. It is not

intended to provide full heat capability.

MODE CONTROL TEMP CONTROL

OFF

LOW

FAN

HIGH

FAN

HIGH

HEAT

HIGH

COOL

LOW

COOL

LOW

HEAT

W

A

R

M

E

R

C

O

L

E

R

OFF

LOW

FAN

HIGH

FAN

HIGH

COOL

LOW

COOL

C

O

L

E

R

About the controls on the air conditioner—models with control knobs.

Horizontal louvers

on the front grille

let you control the

air direction up

and down.

Remove the front

grille to adjust the

vertical louvers

side-to-side to

direct the air left

or right.

7

Temperature Limiting

Limiting the maximum and minimum settings

prevents users from turning the control to the

extreme heat or cool positions.

The normal range of the temp control is

approximately 60°F to 85°F. The control range

may be narrowed by the use of the temperature

limiting screws located behind the control panel.

Each position equals approximately 3°F.

Air Direction

Fan Switch

On Heat/Cool models, the fan switch lever is

located in a hole through the control panel. To

reach it, you need to remove the front grille. Use

a small screwdriver to change the setting. Cool

only models have a rocker switch on the front of

the control box.

When set at CYCLE (down) the fan cycles on and

off when cooling or heating. When set at CONT

(continuous, up) the fan runs all the time,

providing a more balanced temperature.

The unit is shipped in the CONT setting.

www.GEAppliances.com

Limits

heat

temp

Limits

cool

temp

Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support

Vent Control

The vent control is located behind the front grille

on the right side of the air discharge area. When

set at CLOSE, only the air inside the room will be

circulated and conditioned. When set at OPEN,

some inside air is exhausted outside.

To open or close the vent:

1. Remove the front grille.

2. Remove the vent card screw.

3. Remove vent card, turn it over and replace it

by locating rear hole in card over locating pin

inside air discharge and reattaching screw at

front.

Locating hole

Screw hole

OPEN position

(Mesh end toward back)

CLOSE position

(Mesh end toward front)

Locating hole

Screw hole

The unit leaves the factory set at the CLOSE position.

Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions

8

The front grille can be removed for more

thorough cleaning or to make the model and

serial numbers accessible.

To remove:

1. Pull the filter out.

2. Remove the two grille screws.

3. Pull the grille out from the bottom and lift up

from the tabs on the top of the case.

To replace:

Hook the tabs on the front grille even with the

tabs on the case and snap into place.

Replace the screws and filter.

Front Grille

How to Insert the Batteries

Remove the battery cover by sliding it

according to the arrow direction.

Insert new batteries making sure that the

(+) and (–) of battery are installed correctly.

Reattach the cover by sliding it back

into position.

NOTES:

■ Use 2 AAA (1.5 volt) batteries. Do not use

rechargeable batteries.

■ Remove the batteries from the remote control

if the system is not going to be used for a long

time.

3

2

1

9

www.GEAppliances.com

Safety Instructions Operating Instructions Care and Cleaning Installation Instructions Troubleshooting Tips Consumer Support

To maintain optimum performance, clean the filter at least every 30 days.

Air Filter

Turn the air conditioner off before cleaning.

The most important thing you can do to

maintain the air conditioner is to clean the filter

at least every 30 days. A clogged filter reduces

cooling, heating and air flow.

Keeping the air filter clean will:

■ Decrease cost of operation.

■ Save energy.

■ Prevent clogged heat exchanger coils.

■ Reduce the risk of premature component

failure.

To clean the air filters:

■ Vacuum off the heavy soil.

■ Run water through the filters.

■ Dry thoroughly before replacing.

To remove the air filter, on some models:

Carefully pull the tab forward, up and out.

To remove the air filter, on other models:

Pull it down.

To replace the air filter:

Replace the clean filter by pushing it back

into place.

CAUTION: Do not operate the air

conditioner without the filter in place. If a filter

becomes torn or damaged it should be replaced

immediately.

Operating without the filter in place or with a

damaged filter will allow dirt and dust to reach

the indoor coil and reduce the cooling, heating,

airflow and efficiency of the unit.

Replacement filters are available from your

salesperson, GE dealer, GE Service and Parts

Center or authorized Customer Care

®

servicers.

Dirty filter—Needs cleaning Clogged filter—Greatly

reduces cooling, heating

and airflow.

FRONT

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance

requires basic mechanical skills.

• Completion time – Approximately 1 hour

• We recommend that two people install this

product.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com

Installation

Air Conditioner

Instructions

Some models require a 115/120-volt a.c.,

60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility

of electric shock hazard. If the wall outlet you plan to

use is only a 2-prong outlet, it is your responsibility to

have it replaced with a properly grounded 3-prong

wall outlet.

Some models require 230/208-volt a.c.,

protected with a time delay fuse or circuit

breaker. These models should be installed on

their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

ELECTRICAL REQUIREMENTS

CAUTION:

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

IMPORTANT!

GE strongly recommends the removal of the old wall

case and the installation of a new GE Wall Case. If

you decide to keep the existing wall case, you may

need a kit to ensure proper performance. If you DO

NOT use a kit, you run the risk of poor performance

or product failure. This is not covered under the

terms of the GE warranty.

J-MODEL QUALIFYING QUESTIONS

J-model air conditioners may fit in existing wall

cases. However, they often need a kit to properly

adapt the case to the GE air conditioner. Answer

these questions and see the chart on the next page

for the proper kit.

What brand air conditioner will you be

replacing?

What are the dimensions of the wall case

currently in use?

What is the model number of the chassis

currently in use? What is the model (or Type)

number of the wall case currently in use?

Frequently, the J-model adapter kit will apply to

another brand model “series” or specific vintage.

In these cases, you need the chassis model

number and/or the wall case or “type” number

to confirm the use of the correct adapter kit.

What type of outdoor grille is used with the

current wall case?

There may be an architectural grille attached to

a wall case to enhance the exterior appearance

of the building. Custom grilles may be used with

J-model wall cases provided a J-model adapter

kit is also used to ensure proper airflow.

A

C

D

B

10

11

GE KIT NUMBERS

Read these instructions completely and carefully.

Installation Instructions

USE GE

KIT NUMBER: FOR: DESCRIPTION:

RAK56A100 GE RAB13, 14 & 15 Fits all GE wall cases 26″W x 18″H x 24″D

(ACLB & RCL Chassis)

RAK1072 Hotpoint ACXB10 & 11 Adapts an older Hotpoint wall case to a “J”

(ACTB Chassis) model chassis. Fits Hotpoint wall cases

25

3

⁄4″W x 16

7

⁄8″H x 18

5

⁄8″D

RAK1082 Whirlpool Type 23W Adapts Whirlpool wall case to a “J”

Wall Case model chassis. Fits Whirlpool wall

cases 25

7

⁄8″W x 16

1

⁄2″H x 23

1

⁄8″D

RAK1102 GE RAB30 Adapts GE wall case to a “J” model chassis.

(“F” models) Fits the RAB 30 wall case 26″W x 18″H x 24″D

RAK123A64 Fedders Wall Case “A” Adapts Fedders wall case to a “J” model chassis.

Fits Fedders wall cases 27″W x 16

3

⁄4″H x 16

3

⁄4″D

RAK126 Westinghouse Wall Case Adapts Westinghouse wall case to a “J”

(Type 2626D73H01) model chassis. Fits Westinghouse wall

cases 25

7

⁄8″W x 15

7

⁄16″H x 16″D

RAB46, 47 & 48 Use these kits for all Standard wall case for “J” model chassis.

other brands not listed. RAG13 stamped aluminum exterior grille

included. Remove the existing case

and replace.

RAK690 RAB36, 37, 38, 46, 47 or 48 If you attach a custom architectural outdoor

(J-Chassis) grille, use this kit to ensure proper airflow.

RAG13 RAB36, 37, 38, 46, 47 or 48 Standard aluminum exterior grille (included with RAB46, 47, and 48 wall

(J-Chassis) cases)

RAG14E RAB36, 37, 38, 46, 47 or 48 Architectural louvered exterior grille

(J-Chassis)

TOOLS YOU MAY NEED

Adjustable Wrench

Level

Phillips head

screwdriver

Hand or Saber Saw

Drill

Pencil

Ruler or Tape

Measure

Scissors or knife

REMOVE THREE SHIPPING PADS

INSIDE AIR CONDITIONER NEXT TO

COMPRESSOR

Installation Instructions

REMOVE LOCKING PLATE ON

FRONT LEFT SIDE

1

REINSTALL LOCKING PLATE WITH

TAB BEHIND WALL CASE FLANGE.

TIGHTEN SCREW

Locking

plate

Remove

screw

INSTALLING A J-MODEL IN AN EXISTING WALL CASE

Read these instructions completely and carefully.

Remove

shipping

pads

CAREFULLY SLIDE AIR

CONDITIONER BACK INTO CASE

Make sure that the tubing on the unit does

not touch the wall case and that the case

installation is secure.

2

3

12

WHEN WALL OUTLET IS TO LEFT,

EXTEND CORD UNDER UNIT AND

HOLD IT IN PLACE WITH CLAMP

Power

cord

Clamp

ATTACH FRONT GRILLE

An opening for the power cord is on the

bottom of the front grille.

6

ATTACH POWER CORD TO BASE

PAN WITH CLAMP

Clamp

Power

cord

Base pan

4

5

7

13

Installation Instructions

PREPARE OPENING IN WALL

Make certain a wall receptacle is

available close to the hole location or make

arrangements to install a receptacle.

The cord length for the 115-volt models is 72″

to the right and 47″ to the left.

For the 230/208-volt models the cord length is

65″ to the right and 39″ to the left.

1

INSTALLING THROUGH THE WALL

Read these instructions completely and carefully.

SUPPORT REQUIREMENTS FOR

AIR CONDITIONER

The air conditioner wall case may be installed

with 1/4″ min. extension out from the inside

wall or with 1/4″ min. extension out from the

outside wall.

The finished sides of the opening should be

structural wall members.

Lintel – Use a lintel in brick veneer and brick

and block types of wall to support the bricks

or blocks above the opening. Do not allow the

wall case to be used in lieu of a lintel.

Flashing – Install flashing (drip rail) as shown

to prevent water from dripping inside the wall

and down the outside of the building.

2

Trim

molding

(if desired)

Plaster

line

Caulking

(above &

below

the

flashing)

Flashing

(drip rail)

1/4″ min. extension

inside the wall from

the trim molding

Room side

Brick veneer

Lintel angle

(if required)

Caulking

(on all 4

sides on the

outside of

the case)

SUPPORT REQUIREMENTS FOR

AIR CONDITIONER

Mortar between the case and the brick all

around the case may be undercut at about 45°

for improved caulking.

3

Caulking

Top of case

Inside

Outside

Undercut

mortar

Installation Instructions

14

WINDOW INSTALLATION—OPTIONAL

FOR MODELS AJES06LSB, AJES08ASB, AJES10DSB and AJHS08ASB

Read these instructions completely and carefully.

Air conditioner

Type C (painted) (6)

Type D (2)

Type E (4)

Large washer (2)

Adjusting bolt (2)

Lock nut (2)

Spacer (2)

Support bracket hardware

Type A (9)

Type B (2)

Sill support

bracket (2)

2 angles

(left and

right hand)

Case side

gasket (2)

Spring

clip (4)

Window

locking

bracket

Vinyl window

gasket

Bottom window gasket

Filler

Panels

Cut panels

and

discard

center

piece

Case top gasket

Foam top

window gasket

B

Right

side

A

Left side

(holes are on the left)

(holes are on the right)

WINDOW REQUIREMENTS

• These instructions are for a standard double-hung

window. You will need to modify them for other

types of windows.

• The air conditioner can be installed without the

accordion panels if needed to fit in a narrow

window. See the window opening dimensions

to the right.

• All supporting parts must be secured to firm wood,

masonry or metal.

• The electrical outlet must be within reach of the

power cord.

1

Window opening dimensions are for a

standard double-hung window.

17″ min.

31″ to 43″

(With filler panels)

26

1

⁄4″ min.

(Without filler panels)

REMOVE AIR CONDITIONER FROM CASE

Remove the front grille. See the Care and

Cleaning section.

Find the locking plate located on the front

left side.

Remove the screw and the locking plate to

unlock the air conditioner.

Remove and discard the shipping screw

on the back of the air conditioner to allow

removal of the air conditioner from the

case.

Pull the bottom corners of the air

conditioner and slide it out of the case.

Remove the three shipping pads inside the air

conditioner next to the compressor.

Remove the rear grille that is taped to the back

of the case. Remove the packet of screws taped

to the back of the grille. While holding the grille

at a 45° angle, insert it into the clips at the top of

the case and push the bottom in. Keep slight

upward pressure on the grille until it fits flush

with the bottom of the case.

15

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt towards the outside and will

keep it from draining properly. To adjust for this,

attach a piece of wood to the stool.

WOOD PIECES:

WIDTH: 2″

LENGTH: Long enough to fit inside the window

frame.

THICKNESS: To determine the thickness, place a

piece of wood on the stool to make it 1/2″ higher

than the top of the storm window frame.

Attach securely with nails or screws provided by

the installer.

2

1/2″ higher

than

frame

Storm

window

frame

Wood

Stool

Sill

3

A

B

C

Locking

plate

Remove

screw

D

Remove

screw

E

F

If attaching the grille

from the outside of

the case use the 2

long screws.

If attaching the grille

on the inside of the

case use the 2 short

screws.

G

Clips

Insert the 2 long screws on

the outside

Insert the 2 short screws

on the inside

Installation Instructions

Remove

shipping

pads

Installation Instructions

16

INSTALL SILL SUPPORTS

Assemble the sill supports. Do not fully

tighten the spacer mounting screws at this

time.

Before attaching the sill supports, place

them on the window stool. Select the spacer

position that will place the spacer near the

outermost point on the sill. Tighten the

spacer mounting screws.

Turn the bolts and tighten the lock nuts to make

the sill supports level or tilt down 1/8″ to the

outside. Line up the “V” notch with 12

3

⁄8″ marks.

Drill pilot holes and attach the sill supports.

NOTES:

• On narrow sills, there may not be enough room to

use the lock nut.

• A deep offset sill may require a longer adjusting

bolt than the standard hex head bolt provided.

• On wood sills use the large washer between the

bolt head and the sill. This prevents the bolt from

digging into the wood.

PREPARE WINDOW

Mark the centerline of the stool. Measure

from the centerline 13

3

⁄8″ on both sides for

the panel cuts.

Measure 12

3

⁄8″ from the centerline on both sides

for the sill support brackets.

4

A

B

WINDOW INSTALLATION—OPTIONAL (cont.)

Stool

Sill

13

3

⁄8″

Centerline

12

3

⁄8″

Centerline

5

A

B

C

Installation Instructions

17

MEASURE, CUT AND INSTALL

FILLER PANELS

Measure from the edge of the panel marks

(see Prepare the Window) to the inside of

the window track on each side. (A and B)

Mark the A and B measurements on each

side of the filler panel board. Cut the panels

and discard the center piece. Note position

of the notches.

Put together the panel assemblies. Remove

the paper backing from the case side gasket

and attach it to the angle. Push a pencil point

through the gaskets to locate the holes in

the angles.

Install the panels in the window. Place the spring

clips 3″ from the top and the bottom. Squeeze

and push the clips to fit in the window track and

the tab into the sill support.

6

A

B

C

D

Sill

A

Window track

Width of the air

conditioner

(panel marks)

Left side

B

Right side

13

3

⁄8″ 13

3

⁄8″

Filler

Panels

Cut

panels

and

discard

center

piece

B

Right

side

A

Left

side

(holes are on the left)

(holes are on the right)

Gasket

Angle

Panel

Tab

Type C

(painted

screws)

Angle

Hook the tab into

the sill support

3″

INSTALL CASE IN WINDOW

Peel off the backing from the bottom

window gasket.

Place the gasket on the stool and over the

brackets, even with the rear edge, sticky

side down.

Carefully slide the empty case into the

window until the holes in the case line up

with the holes in the panel angles.

NOTES:

• The case should have a 1/8″ minimum tilt

toward the outside.

• Be sure the seal gasket and panel gaskets

remain in position and do not roll with the

case.

Lower the window so it fits behind the panel

tabs. Insert the 4 type A screws through the

holes in the case and into the panel angles,

2 on each side.

With the window closed, mark where the

window sash meets the case.

Peel off the backing from the case top gasket.

Hold on to the case, open the window, and

place the gasket along the mark on the case.

Place the vinyl window gasket over the case top

gasket. Insert the panel tabs through the slits in

the gasket. Cut the gasket on each side to the

width of the window.

Close the window tightly on the vinyl gasket.

Bend the gasket forward to expose the panel

tabs. Drill pilot holes into the window sash.

Installation Instructions

18

WINDOW INSTALLATION—OPTIONAL (cont.)

7

A

B

C

D

E

F

G

H

I

Bottom window gasket

Case holes

Panel

tabs

Case

screws

Put the gasket

on top of the

case where

the window

will close.

Panel

tab

Vinyl window

gasket

Attach the panel tab

to the window on

each side with a type

D screw.

Installation Instructions

19

REPLACE AIR CONDITIONER IN

CASE

Carefully slide the air conditioner back into

the case.

Attach the power cord to the base pan with

the clamp.

When the wall outlet is to the left, extend the

cord under the unit and hold it in place with the

clamp.

Reinstall the locking plate with the tab behind the

wall case flange. Tighten the screw.

Reattach the front grille. An opening for the

power cord is on the bottom of the front grille.

Fill holes and cracks with caulking provided by

the installer

.

INSTALL WINDOW GASKET AND

LOCKING BRACKET

Cut the foam top window gasket to the

window width.

Stuff the foam between the glass and the

window to prevent air and insects from

getting into the room.

Attach the window locking bracket with 1 type E

screw.

8

A

B

9

A

B

C

D

E

F

Clamp

Power cord

Base pan

Power cord

Clamp

Locking

plate

Tighten

screw

Consumer Support Troubleshooting Tips Installation Instructions Care and Cleaning Operating Instructions Safety Instructions

20

Before you call for service…

Troubleshooting Tips: Save time and money! Review the chart below first and you may not need to call for service.

Normal Operating Sounds

■ You may hear a pinging noise caused by

water being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

■ You may hear the thermostat click when the

compressor cycles on and off.

■ Water will collect in the base pan during

high humidity or on rainy days. The water

may overflow and drip from the outdoor side

of the unit.

■ The fan may run even when the compressor

does not.

Problem Possible Causes What To Do

Air conditioner The air conditioner • Make sure the air conditioner plug is pushed

does not start is unplugged. completely into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and

breaker is tripped. replace the fuse or reset the breaker.

Power failure. • If power failure occurs, turn the air conditioner

OFF. When power is restored, wait 3 minutes to

restart the air conditioner to prevent tripping of

the compressor overload.

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or furniture

not cool as it should blocking the front of the air conditioner.

The temp control may • On models with touch pads: In COOL mode, press the

not be set correctly. DECREASE ▼ pad.

• On models with control knobs, turn the temperature

knob to a higher number.

The air filter is dirty. • Clean the filter at least every 30 days.

See the Operating Instructions section.

The room may have been hot. • When the air conditioner is first turned on, you need

to allow time for the room to cool down.

Cold air is escaping. • Check for open furnace registers and cold air returns.

• Set the air conditioner’s vent to the closed position.

Cooling coils have iced up. • See “Air conditioner freezing up” below.

Air conditioner Ice blocks the airflow • On models with control knobs, set the mode control

freezing up and stops the air conditioner at HIGH FAN or HIGH COOL with the temp at WARMER.

from cooling the room.

• On models with touch pads, set the controls at

HIGH FAN or HIGH COOL and set the thermostat to

a higher temperature.

The remote control is The batteries are inserted • Check the position of the batteries. They should be

not working incorrectly. inserted correctly.

The batteries may be dead. • Replace the batteries.

Water drips outside Hot, humid weather. • This is normal.

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air

tilted to the outside. conditioner slants slightly from the case front to the

rear.

Water collects in Moisture removed from air • This is normal for a short period in areas with little

base pan and drains into base pan. humidity; normal for a longer period in very humid

areas.

La page charge ...

GE 10 DCB Manuel utilisateur

Ce manuel convient également à

GE 10 DCB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents