9761966
ELECTRICRANGE
Lse
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-807-6777
or visit our website at www.inglis.oa
CUISINIERE
ELECTRIQUE
Pour assistance, installation ou service,
composez le 1-800-807-6777
ou visitez notre site web & www.inglis.ca
Table of Contents/Table des matieres .................. 2
iMPORTANT:
Save for local electrical inspector's use.
Installer: Leave installation instructions with the
homeowner.
Homeowner: Keep installation instructions for future
reference.
iMPORTANT :
,&,conserver pour consultation par I'inspecteur local
des installations electriques.
Installateur : Remettre les instructions d'installation
au proprietaire.
Proprietaire :Conserver les instructions d'installation
pour reference ulterieure.
TABLEOFCONTENTS
RANGE SAFETY ............................................................................. 3
The Anti-Tip Bracket .................................................................... 3
PARTS AND FEATURES ................................................................ 5
COOKTOP USE .............................................................................. 6
Cooktop Controls ......................................................................... 6
Ceramic Glass (on some models) ................................................ 6
Coil Elements and Burner Bowls (on some models) ................... 7
Lift-up Cooktop (on some models) .............................................. 7
Home Canning ............................................................................. 7
Cookware ..................................................................................... 8
ELECTRONIC OVEN CONTROL ................................................... 8
Oven Indicator Lights ................................................................... 8
Display .......................................................................................... 8
Start/Enter .................................................................................... 8
Off/Cancel .................................................................................... 9
Clock ............................................................................................ 9
Tones ............................................................................................ 9
Fahrenheit and Celsius ................................................................. 9
Timer ............................................................................................. 9
Control Lock ................................................................................. 9
Oven Temperature Control .......................................................... 9
OVEN USE ..................................................................................... 10
Aluminum Foil............................................................................. 10
Positioning Racks and Bakeware .............................................. 10
Bakeware .................................................................................... 10
Meat Thermometer ..................................................................... 11
Oven Vent ................................................................................... 11
Baking and Roasting .................................................................. 11
Broiling and Custom Broiling ..................................................... 11
Timed Cooking ........................................................................... 12
RANGE CARE ............................................................................... 13
Self-Cleaning Cycle (on some models) ...................................... 13
General Cleaning ........................................................................ 13
Oven Light (on some models) .................................................... 15
Appliance Outlets ....................................................................... 15
Oven Door .................................................................................. 15
Storage Drawer .......................................................................... 16
TROUBLESHOOTING .................................................................. 16
ASSISTANCE OR SERVICE ......................................................... 17
WAR RAN TY .................................................................................. 18
TABI DESMATIERES
SI_CURITI_ DE LA CUISINII_RE ................................................... 19
La bride antibasculement ........................................................... 19
PIECES ET CARACTERISTIQUES .............................................. 22
UTILISATION DE LA TABLE DE CUISSON ................................ 23
Commandes de la table de cuisson .......................................... 23
Vitroceramique (sur certains modeles) ....................................... 23
elements en spirale et cuvettes des brOleurs
(sur certains modeles) ................................................................ 24
Table de cuisson relevable (sur certains modeles) .................... 24
Preparation de conserves a la maison ....................................... 24
Ustensiles de cuisson ................................................................ 25
COMMANDE I_LECTRONIQUE
DU FOUR ....................................................................................... 25
Temoins lumineux du four .......................................................... 25
Affichage ..................................................................................... 25
Mise en marche/entree .............................................................. 25
Arr_t/annulation .......................................................................... 26
Horloge ....................................................................................... 26
Signaux sonores ......................................................................... 26
Fahrenheit et Celsius .................................................................. 26
Minuterie ..................................................................................... 26
Verrouillage des commandes ..................................................... 26
Commande de la temperature du four ...................................... 26
UTILISATION DU FOUR ............................................................... 27
Papier d'aluminium ..................................................................... 27
Positionnement des grilles et des ustensiles de cuisson .......... 27
Ustensiles de cuisson ................................................................ 27
Thermom_tre a viande ............................................................... 28
Event du four .............................................................................. 28
Cuisson au four et rGtissage ...................................................... 28
Cuisson au gril et cuisson au gril personnalisee ........................ 29
Cuisson minutee ......................................................................... 30
ENTRETIEN DE LA CUISINII_RE ................................................. 30
Programme d'autonettoyage (sur certains modeles) ................ 30
Nettoyage general ...................................................................... 31
Lampe du four (sur certains modeles) ....................................... 33
Prises pour appareils menagers ................................................ 33
Porte du four ............................................................................... 33
Tiroir de remisage ....................................................................... 34
DCPANNAGE ................................................................................. 34
ASSISTANCE OU SERVICE ......................................................... 35
GARANTI E ..................................................................................... 36
RANGESAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without
having the anti-tip bracket fastened down properly.
Anti-Tip Bracket
Range Foot
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children and adults.
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
iMPORTANT SAFETY iNSTRUCTiONS
WARNING: To reduce the risk of fire, electrical shock,
injury to persons, or damage when using the range, follow
basic precautions, including the following:
[] WARNING: TO REDUCE THE RISK OF TiPPiNG OF THE
RANGE, THE RANGE MUST BE SECURED BY
PROPERLY iNSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR, AND SLIDE RANGE
BACK SO REAR RANGE FOOT IS UNDER ANTI-TIP
BRACKET.
[] CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range -
children climbing on the range to reach items could be
seriously injured.
[] Proper Installation - Be sure the range is properly installed
and grounded by a qualified technician.
[] Never Use the Range for Warming or Heating the Room.
[] Do Not Leave Children Alone - Children should not be left
alone or unattended in area where the range is in use.
They should never be allowed to sit or stand on any part of
the range.
[] Wear Proper Apparel - Loose-fitting or hanging garments
should never be worn while using the range.
[] User Servicing - Do not repair or replace any part of the
range unless specifically recommended in the manual. All
other servicing should be referred to a qualified technician.
[] Storage in or on the Range - Flammable materials should
not be stored in an oven or near surface units.
[] Do Not Use Water on Grease Fires - Smother fire or flame
or use dry chemical or foam-type extinguisher.
[] Use Only Dry Potholders - Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholder touch hot heating elements. Do not use a towel
or other bulky cloth.
[] DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS - Surface units may be hot even though they are
dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch,
or let clothing or other flammable materials contact surface
units or areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and surfaces
facing the cooktop.
[] Use Proper Pan Size - The range is equipped with one or
more surface units of different size. Select utensils having
flat bottoms large enough to cover the surface unit heating
element. The use of undersized utensils will expose a
portion of the heating element to direct contact and may
result in ignition of clothing. Proper relationship of utensil to
burner will also improve efficiency.
[] Never Leave Surface Units Unattended at High Heat
Settings - Boilover causes smoking and greasy spillovers
that may ignite.
[] Make Sure Reflector Pans or Drip Bowls Are in Place -
Absence of these pans or bowls during cooking may
subject wiring or components underneath to damage.
[] Protective Liners - Do not use aluminum foil to line surface
unit drip bowls or oven bottoms, except as suggested in
the manual. Improper installation of these liners may result
in a risk of electric shock, or fire.
[] Glazed Cooking Utensils - Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for range-top service without breaking
due to the sudden change in temperature.
[] Utensil Handles Should Be Turned Inward and Not Extend
Over Adjacent Surface Units - To reduce the risk of burns,
ignition of flammable materials, and spillage due to
unintentional contact with the utensil, the handle of a
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface units.
[] Do Not Soak Removable Heating Elements - Heating
elements should never be immersed in water.
[] Do Not Cook on Broken Cooktop - If cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
[] Clean Cooktop With Caution - If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to
avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface.
[] Use Care When Opening Door - Let hot air or steam
escape before removing or replacing food.
[] Do Not Heat Unopened Food Containers - Build-up of
pressure may cause container to burst and result in injury.
[] Keep Oven Vent Ducts Unobstructed.
[] Placement of Oven Racks - Always place oven racks in
desired location while oven is cool. If rack must be moved
while oven is hot, do not let potholder contact hot heating
element in oven.
[] DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN - Heating elements may be hot even
though they are dark in color. Interior surfaces of an oven
become hot enough to cause burns. During and after use,
do not touch, or let clothing or other flammable materials
contact heating elements or interior surfaces of oven until
they have had sufficient time to cool. Other surfaces of the
appliance may become hot enough to cause burns - among
these surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven doors.
For self-cleaning ranges -
[] Do Not Clean Door Gasket - The door gasket is essential
for a good seal. Care should be taken not to rub, damage,
or move the gasket.
[] Do Not Use Oven Cleaners - No commercial oven cleaner
or oven liner protective coating of any kind should be used
in or around any part of the oven.
[] Clean Only Parts Listed in Manual.
[] Before Self-Cleaning the Oven - Remove broiler pan and
other utensils.
For units with ventilating hood -
[] Clean Ventilating Hoods Frequently - Grease should not
be allowed to accumulate on hood or filter.
[] When flaming foods under the hood, turn the fan on.
SAVE THESE iNSTRUCTiONS
PARTSANDFEATURES
This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The
location and appearance of the features shown here may not match those of your model.
Control Panel
/
Range
D E F G
A. Left front control knob
B. Surface heating indicator light
C. Left rear control knob
D. Electronic oven control
E. Right rear control knob
E Right front control knob
G. Surface cooking area locater
B
\
/I
G
H
I
J
A. Surface cooking area or element
B. Anti-tip bracket
C. Doorstop clip
D. Model and serial number plate
(behind left side of storage drawer)
E. Storage drawer
E Control panel
G. Hot surface indicator light
(on ceramic glass models)
H. Automatic oven light switch
(on some models)
I. Gasket
J. Broil element (not shown)
K. Bake element
L. Self-clean latch
(on some models)
Parts and Features not shown
(on some models)
Coil elements
Oven door window
Oven light
Manual oven light switch
COOKTOPUSE
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
The control knobs can be set to anywhere between HI and LO.
Push in and turn to setting. On some models, the surface cooking
area Iocator shows which element is turned on. Use the following
chart as a guide when setting heat levels.
SETTING RECOMMENDED USE
HI • Start food cooking.
• Bring liquid to a boil.
Medium High • Hold a rapid boil.
6-8
• Quickly brown or sear food.
Medium • Maintain a slow boil.
5
• Fry or saute foods,
Medium Low • Cook soups, sauces and gravies.
2-4
• Stew or steam food.
• Simmer.
LO • Keep food warm.
• Melt chocolate or butter.
I
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
NOTE: On self-cleaning models, the cooktop will not operate
when the range is in a self-cleaning mode,
The surface cooking area will glow red when an element is on. It
will cycle on and off, at all settings, to maintain the selected heat
level.
It is normal for the surface of white or biscuit ceramic glass to
appear to change color when surface cooking areas are hot. As
the glass cools, it will return to its original color.
Wiping off the cooktop before and after each use will help keep it
free from stains and provide the most even heating. On cooktops
with white or biscuit ceramic glass, soils and stains may be more
visible, and may require more cleaning and care. For more
information, see "General Cleaning" section.
• Do not store jars or cans above the cooktop. Dropping a
heavy or hard object onto the cooktop could crack the
cooktop.
• Do not leave a hot lid on the cooktop. As the cooktop cools,
air can become trapped between the lid and the cooktop,
and the ceramic glass could break when the lid is removed.
For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
while the surface is still warm. If sugary spills are allowed to
cool down, they can adhere to the cooktop and can cause
pitting and permanent marks.
Do not slide cookware or bakeware across the cooktop.
Aluminum or copper bottoms and rough finishes on
cookware or bakeware could leave scratches or marks on the
cooktop.
• Do not cook popcorn in prepackaged aluminum containers
on the cooktop. They could leave aluminum marks that
cannot be removed completely.
• Do not allow objects that could melt, such as plastic or
aluminum foil, to touch any part of the entire cooktop.
• Do not use the cooktop as a cutting board.
• Use cookware about the same size as the surface cooking
area. Cookware should not extend more than 1/2"(1.3 cm)
outside the area.
--B
A. Surface cooking area
B. Cookware/canner
C. V2"(1.3 cm) Maximum overhang
Use flat-bottomed cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed or
dented bottoms could cause uneven heating and poor
cooking results.
Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the ruler,
no space or light should be visible between it and the
cookware.
Cookware designed with slightly indented bottoms or small
expansion channels can be used.
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
• Do not cook foods directly on the cooktop.
Hot Surface Indicator Light (under ceramic glass)
The hot surface indicator light will glow as long as any surface
cooking area is too hot to touch, even after the surface cooking
area(s) is turned off.
Coil elements should be level for optimal cooking results. Burner
bowls, when clean, reflect heat back to the cookware. They also
help catch spills.
Cookware should not extend more than 1/2"(1.3 cm) over the coil
element. If cookware is uneven or too large, it can produce
excess heat causing the burner bowl to change color. For more
information, see the "General Cleaning" section.
NOTE: Before removing or replacing coil elements and burner
bowls, make sure they are cool and the control knobs are in the
Off position.
To Remove:
1. Push in the edge of coil element toward the receptacle. Then
lift it just enough to clear the burner bowl.
To Replace:
1. Line up openings in the burner bowl with the coil element
receptacle.
\
2. Holding the coil element as level as possible, slowly push coil
element terminal into the receptacle.
3. When the terminal is pushed into the receptacle as far as it
will go, push down the edge of the coil element opposite the
receptacle.
The lift-up cooktop provides easy access for cleaning beneath.
Do not drop the cooktop. Damage could occur to the finish and
the cooktop frame. For more information, see the "General
Cleaning" section.
To Lift:
Lift the cooktop by both front corners until the supports lock into
place.
To Replace:
1. Lift the cooktop from both sides while pressing the support
rods back to unlock them.
2. Slowly lower the cooktop into place.
2. Pull the coil element straight away from the receptacle.
3. Lift out the burner bowl.
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
• Center the canner on the grate or largest surface cooking
area or element. Canners should not extend more than
1/2"(1.3 cm) outside the cooking area.
• Do not place canner on 2 surface cooking areas, elements or
surface burners at the same time.
• On ceramic glass models, use only flat-bottomed canners.
On coil element models, the installation of a Canning Unit Kit
is recommended. If a kit is not installed, the life of the coil
element will be shortened. See "Assistance or Service" for
ordering instructions.
• For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
IMPORTANT:Donotleaveemptycookwareonahotsurface
cookingarea,elementorsurfaceburner.
Idealcookwareshouldhaveaflatbottom,straightsidesanda
well-fittinglidandthematerialshouldbeofmedium-to-heavy
thickness.
Roughfinishesmayscratchthecooktop.Aluminumandcopper
maybeusedasacoreorbaseincookware.However,whenused
asabasetheycanleavepermanentmarksonthecooktopor
grates.
Cookwarematerialisafactorinhowquicklyandevenlyheatis
transferred,whichaffectscookingresults.Anonstickfinishhas
thesamecharacteristicsasitsbasematerial.Forexample,
aluminumcookwarewithanonstickfinishwilltakeonthe
propertiesofaluminum.
Cookwarewithnonsticksurfacesshouldnotbeusedunderthe
broiler.
Usethefollowingchartasaguideforcookwarematerial
characteristics.
COOKWARE CHARACTERISTICS
Aluminum • Heatsquicklyandevenly.
• Suitableforalltypesofcooking.
• Mediumorheavythicknessisbestfor
mostcookingtasks.
Castiron • Heatsslowlyandevenly.
• Goodforbrowningandfrying.
• Maintainsheatforslowcooking.
Ceramicor • Followmanufacturer'sinstructions.
Ceramicglass • Heatsslowly,butunevenly.
• Idealresultsonlowtomediumheat
settings.
Copper • Heatsveryquicklyandevenly.
Earthenware • Followmanufacturer'sinstructions.
• Useonlowheatsettings.
Porcelain • Seestainlesssteelorcastiron.
enamel-on-
steelorcast
iron
Stainlesssteel • Heatsquickly,butunevenly.
• Acoreorbaseofaluminumorcopper
onstainlesssteelprovideseven
heating.
ELECTRONICOVENCONTROL
B CDE F
Bake Broil Clean Or_
Delay Door Controls
Locked Locked
K J / H
A. Oven display
B. Clock
C. Timer/cancel
D. Start/enter
(control lock)
E.Auto clean
SELF_CLEANIN G OVEN
G
F.Off/cancel
G.Temperature/time
H.Cook time
LStart time
J. Custom broil
K.Bake
The indicator lights are located along all 4 sides of the display.
The indicator lights light up or flash when the oven is in one of the
following modes: Bake, Broil, Clean (on some models), On,
Start?, Controls Locked, Door Locked (on some models), Delay,
Timer, Temp, Cook Time, or Start Time.
When power is first supplied to the appliance, "PF" or a flashing
time will appear on the display. Press OFF/CANCEL to clear.
If "PF" or a flashing time appears at any other time, a power
failure has occurred. Press OFF/CANCEL and reset the clock if
needed.
When the oven is in use, the display shows preheat time or oven
temperature setting.
When the oven is not in use, the display shows the time of day.
When using Start Time/Cook Time, the display will show either
hours and minutes, or minutes and seconds.
When setting a function, if Start/Enter is not pressed, and after
5 seconds, the "Start?" oven indicator light will flash. Press
START/ENTER, or after 1 minute, the set function will be
canceled.
The Start/Enter pad begins any oven function, the Start/Enter
pad is not pressed within 5 seconds after pressing afunction
pad, the "Start?" indicator light will flash as a reminder.
If Start/Enter is not pressed within 1 minute after pressing a
function pad, the oven display will return to the time of day mode
and the programmed function will be canceled.
TheOff/CancelpadstopsanyfunctionexcepttheClock,Timer
andControlLock.
Thecoolingfanmaycontinuetooperateafteranovenfunction
hasbeencanceled,dependingonoventemperature.
Thisisa12-hourclockanddoesnotshowa.m.orp.m.
ToSet:
Beforesetting,makesuretheovenandTimerareoff.
1. PressCLOCK.
2. PresstheTEMP/TIME"up"or"down"arrowpadtosetthe
timeofday.
PressSTART/ENTERorCLOCK.
Tonesareaudiblesignals,indicatingthefollowing:
One tone
• Valid pad press
• Oven is preheated (long tone)
• Function has been entered
• Reminder, repeating each minute after the end-of-cycle tones
Three tones
• Invalid pad press
Four tones
• End of cycle
The temperature is preset at Fahrenheit, but can be changed to
Celsius on some models.
To Change: Press and hold CUSTOM BROIL for 5 seconds. A
tone will sound, and "°C" will appear on the display. Repeat to
change back to Fahrenheit. To exit mode, press OFF/CANCEL.
The Timer can be set in hours or minutes up to 12 hours and
59 minutes and counts down the set time.
NOTE: The Timer does not start or stop the oven.
To Set:
1. Press TIMER CANCEL*.
The timer oven indicator light will light up. If no action is taken
after 1 minute, the display will return to the time of day mode.
2. Press the TEMP/TIME "up" or "down" arrow pad to set the
length of time.
3. Press START/ENTER.
When the set time ends, four 1-second tones will sound.
4. Press TIMER CANCEL* anytime to cancel the timer and/or
stop reminder tones. To cancel the timer during the
countdown, press TIMER CANCEL* twice.
The time can be reset during the countdown by repeating the
above steps. To display the time of day when the timer is
counting down, press CLOCK.
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven.
When the control is locked, only the Clock and Timer pads will
function.
To Lock/Unlock Control: Before locking, make sure the oven
and Timer are off. Touch and hold START/ENTER for 5 seconds.
A single tone will sound, and "LOC" and "LOCK'D" (on some
models) will appear on the display. "LOC" will also appear
whenever any command pad is pressed while the control is
locked.
Repeat to unlock. "LOC" and "LOCK'D" (on some models) will
disappear from the display.
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door and element or
burner cycling may give incorrect readings.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted.
A minus sign means the oven will be cooler by the displayed
amount. The absence of a minus sign means the oven will be
warmer by the displayed amount. Use the following chart as a
guide.
ADJUSTMENT °F COOKS FOOD
10°F (5°C) ...a little more
20°F (10°C) ...moderately more
30°F (15°C) ...much more
-10°F (-5°C) ...a little less
-20°F (-10°C) ...moderately less
-30°F (-15°C) ...much less
To Adjust Oven Temperature Calibration:
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example "00."
2. Press the TEMP/TIME "up" or "down" arrow pad to increase
or to decrease the temperature in 10°F (10°C) amounts. The
adjustment can be set between 30°F (30°C) and
-30OF (-30oc).
NOTE: All temperature adjustments will be displayed in
Fahrenheit.
3. Press START/ENTER.
OVENUSE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled,
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room,
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
• Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
• To catch spills, place foil on rack below dish. Make sure foil is
at least 1/2"(1.3 cm) larger than the dish and that it is turned
up at the edges.
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow
2" (5 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
NUMBEROF POSITION ON RACK
PAN(S)
1 Center of rack.
2 Side by side or slightly staggered.
3 or 4 Opposite corners on each rack. Make sure
that no bakeware piece is directly over
another.
.....
Cl,,_S ,,
4 _ _ /:R%;; R# s,
IMPORTANT: Do net place food or bakeware directly on the oven
door or bottom. Permanent damage will occur to the porcelain
finish,
Rack position 5 cannot be used on this model.
RACKS
NOTES:
• Position racks before turning the oven on.
• Do not move racks with bakeware on them.
• Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front
edge, then lift out. Use the following illustration and chart as a
guide.
The bakeware material affects cooking results. Follow
manufacturer's recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
BAKEWARE/ RECOMMENDATIONS
RESULTS
Light colored • Use temperature and time
aluminum recommended in recipe.
• Light golden
crusts
• Even browning
Dark aluminum and •
other bakeware with
dark, dull and/or
nonstick finish •
• Brown, crisp •
crusts
May need to reduce baking
temperatures 25°F (15°C).
Use suggested baking time.
For pies, breads and casseroles,
use temperature recommended in
recipe.
• Place rack in center of oven.
Insulated cookie
sheets or baking
pans
• Little or no
bottom browning
• Place in the bottom third of oven.
• May need to increase baking time.
FOOD RACK POSITION
Frozen pies, large roasts, turkeys, 1 or 2
angel food cakes
Stainless steel
• Light, golden
crusts
• Uneven browning
• May need to increase baking time.
Stoneware • Follow manufacturer's
• Crisp crusts instructions.
Bundt cakes, most quick breads, yeast 2
breads, casseroles, meats
Cookies, biscuits, muffins, cakes, 2 or 3
nonfrozen pies
Ovenproof
glassware, ceramic
glass or ceramic
• Brown, crisp
crusts
• May need to reduce baking
temperatures 25°F (15°C).
10
On models without a temperature probe, always rely on a meat
thermometer to determine doneness of meat and poultry. The
internal temperature, not appearance, is what counts. A meat
thermometer is not supplied with this appliance.
• Insert the thermometer into the center of the thickest portion
of the meat or inner thigh or breast of poultry. The tip of the
thermometer should not touch fat, bone or gristle.
• After reading the thermometer once, push it into the meat
1/2"(1.3 cm) more and read again. Ifthe temperature drops,
cook the meat or poultry longer.
• Check all meat in 2 or 3 places.
A. Oven vent (ceramic
glass model)
A. Oven vent (coil
element model)
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Blocking or covering the vent
will cause poor air circulation, affecting cooking and cleaning
results. Do not set plastics, paper or other items that could melt
or burn near the oven vent.
On coil element models, the element can be used when the oven
is in use as long as the cookware does not extend more than
1/2"(1.3 cm) over the element.
Before baking and roasting, position racks according to the
"Positioning Racks and Bakeware" section. When roasting, it is
not necessary to wait for the oven preheat conditioning time to
end before putting food in unless recommended in the recipe.
To Bake or Roast:
1. Press BAKE. The bake oven indicator light will light up.
2. Set the temperature (optional).
Press TEMP/TIME "up" or "down" arrow pad to set a
temperature other than 350°F (177°C) in 5°F (5°C) amounts.
The bake range can be set between 170°F (77°C) and
500°F (260°0).
When the oven temperature is greater than 170°F (77°C), no
preheat conditioning time will be shown in the display.
The preheat conditioning time will not change if the
temperature is reset before the countdown time ends.
If baking and roasting while the minute timer is counting
down, the set temperature can be seen for 5 seconds by
pressing BAKE.
3. Press START/ENTER.
The oven control automatically sets preheating times based
on the oven temperature selected.
The temperature can be changed after this step. START/
ENTER does not need to be pressed again.
After the oven is preheated and the countdown time is
finished, a 1-second tone will sound, the ON indicator light
will go off and the set temperature will appear on the display.
4. Press OFF/CANCEL when finished.
Preheating
After START/ENTER is pressed, the oven will enter a timed
preheat conditioning. "PrE" and the time countdown will appear
on the display. When the preheat conditioning time ends, atone
will sound and the selected temperature will appear on the
display.
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ.
Waiting an additional 10 minutes after the preheat conditioning
time ends to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
Broiling uses direct radiant heat to cook food. Changing the
temperature when Custom Broiling allows more precise control
when cooking. The lower the temperature, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, fish
and poultry may cook better at lower broiling temperatures.
• For best results, use a broiler pan and grid. They are
designed to drain juices and help prevent spatter and smoke.
If you would like to purchase a broiler pan, one may be
ordered. Ask for Part Number 4396923.
For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to prevent curling.
Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
Before broiling, position rack according to Broiling Chart. It is not
necessary to preheat the oven before putting food in unless
recommended in the recipe. Position food on grid in the broiler
pan, then place it in the center of the oven rack. Close the door to
the broil stop position to ensure proper broiling temperature.
11
To Broil:
1. Press CUSTOM BROIL. The broil oven indicator light will light
up.
2. Press START/ENTER. The On and Heat oven indicator lights
will light up.
The temperature setting can be changed any time before or
after pressing START/ENTER. See "Custom Broiling" section.
If broiling while the time is counting down, the set broiling
temperature can be seen for 5 seconds by pressing CUSTOM
BROIL.
3. Press OFF/CANCEL when finished.
Custom Broiling
If foods are cooking too fast, press the TEMP/TIME "up" or
"down" arrow pad until 325°F (163°C) shows on the display.
f. Press CUSTOM BROIL to broil foods slower from the start of
cooking.
2. Press the TEMP/TIME "up" or "down" arrow pad to enter a
temperature between 300°F and 500°F (149°C and 260°C).
3. Press START/ENTER.
4. Press OFF/CANCEL when finished.
BROILING CHART
For best results, place food 3" (7 cm) or more from the broil
element. Times are guidelines only and may need to be adjusted
for individual foods and tastes. Recommended rack positions are
numbered from the bottom (1)to the top (5). For diagram, see the
"Positioning Racks and Bakeware" section.
COOK TIME
RACK (in minutes)
FOOD POSITION Side 1 Side 2
Steak
1" (2.5 cm) thick
medium rare 4 14-15 7-8
medium 4 15-16 8-9
well-done 4 18-19 9-10
Ground meat patties*
3/4"(2 cm) thick
well-done 4 13-14 7-8
Pork chops
1" (2.5 cm) thick 4 20-22 10-11
Ham slice, precooked
1/2"(1.25 cm) thick 4 8-10 4-5
Frankfurters 4 5-7 3-4
Lamb chops
1" (2.5 cm)thick 4 14-17 8-9
Chicken
bone-in pieces 3 17-20 17-20
boneless breasts 4 11-16 11-16
Fish
Fillets
1/4-1/2"(0.6-1.25 cm) thick 4 8-10 4-5
Steaks
3/4-1"(2-2.5 cm) thick 4 16-18 8-9
*Place up to 9 patties, equally spaced, on broiler grid.
Food Poisoning Hazard
Do not let food sit in oven more than one hour before
or after cooking.
Doing so can result in food poisoning or sickness.
Timed Cooking allows the oven to be set to turn on at a certain
time of day, cook for a set length of time, and/or shut off
automatically. Delay start should not be used for food such as
breads and cakes because they may not bake properly.
To Set a Cook Time:
1. Press BAKE. The bake oven indicator light will light up.
2. Set the temperature (optional).
Press the TEMP/TIME "up" or "down" arrow pads to enter a
temperature other than the one displayed.
3. Press COOK TIME. The cook time oven indicator light will
light up.
4. Press TEMP/TIME "up" or "down" arrow pads to enter the
length of time to cook.
5. Press START/ENTER.
The display will count down the time.
When the time ends, the oven will shut off automatically and
"End" will appear on the display.
6. Press OFF/CANCEL or open the oven door to clear the
display.
To Set a Delayed Cook Time:
Before setting, make sure the clock is set to the correct time of
day. See "Clock" section.
1. Press BAKE.
2. Set the temperature (optional).
Press the TEMP/TIME "up" or "down" arrow pads to enter a
temperature other than the one displayed.
3. Press COOK TIME.
The cook time oven indicator light will light up.
4. Press the TEMP/TIME "up" or "down" arrow pads to enter the
length of time to cook.
5. Press START TIME.
The start time/delay oven indicator light will light up.
6. Press the TEMP/TIME "up" or "down" arrow pads to enter the
time of day to start.
7. Press START/ENTER.
When the start time is reached, the oven will automatically
turn on.
The temperature and/or time settings can be changed any
time after pressing START/ENTER by repeating steps 2-7.
When the set cook time ends, the oven will shut off
automatically and "End" will appear on the display.
8. Press OFF/CANCEL or open the oven door to clear the
display.
12
£,AN CARE
Burn Hazard
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during
Self-Cleaning cycle.
Failure to follow these instructions can result in burns.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well-ventilated room.
Self-clean the oven before it becomes heavily soiled. Heavy soil
results in longer cleaning and more smoke.
Keep the kitchen well-ventilated during the Self-Cleaning cycle to
help get rid of heat, odors, and smoke.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see
"Oven Vent" or "Oven Vents" section.
Do not clean, rub, damage or move the oven door gasket. The
door gasket is essential for a good seal.
Prepare Oven:
• Remove the broiler pan, grid, cookware and bakeware and,
on some models, the temperature probe from the oven.
• Remove any foil from the oven because it may burn or melt,
damaging the oven.
• Remove oven racks to keep them shiny and easy to slide.
See "General Cleaning" section for more information.
Hand clean inside door edge and the 11/2"(3.8 cm) area
around the inside oven cavity frame, being certain not to
move or bend the gasket. This area does not get hot enough
during self-cleaning to remove soil. Do not let water, cleaner,
etc. enter slots on door frame. Use a damp cloth to clean this
area.
Wipe out any loose soil to reduce smoke and avoid damage.
At high temperatures, foods react with porcelain. Staining,
etching, pitting or faint white spots can result. This will not
affect cooking performance.
Prepare Cooktop and Storage Drawer:
• Remove plastic items from the cooktop because they may
melt.
• Remove all items from the storage drawer.
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
The Self-Cleaning cycle uses very high temperatures, burning soil
to a powdery ash.
The oven is preset for a 3 hour 30 minute clean cycle, but
the time can be changed. Suggested clean times are
2 hours 30 minutes for light soil and between 3 hours 30 minutes
and 4 hours 30 minutes for average to heavy soil.
Once the oven has completely cooled, remove ash with a damp
cloth. Do not wipe down any of the inside surfaces until the oven
has completely cooled down. Applying a cool, damp cloth to the
inner door glass before it has cooled completely could result in
the glass breaking.
The oven light will not work during the Self-Cleaning cycle.
To Self-Clean:
Before self-cleaning, make sure the door is closed completely or
it will not lock and the cycle will not begin.
f. PressAUTO CLEAN.
2. Press the TEMP/TIME "up" or "down" arrow pad to set a
clean time other than 3 hours 30 minutes. The clean time can
be set between 2 hours 30 minutes and 4 hours 30 minutes.
3. Press START/ENTER.
The oven door will automatically lock. The ON and DOOR
LOCKED oven indicator lights will light up. The door will not
unlock until the oven cools.
When the cycle is complete and the oven cools, "End" will
appear on the oven display and the oven indicator lights will
go off.
4. Press OFF/CANCEL to clear the oven display.
To Stop Self-Clean anytime:
Press OFF/CANCEL. If the oven temperature is too high, the door
will remain locked. It will not unlock until the oven cools.
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions
on cleaning products.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES (on some models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire appliance is cool. These spills
may affect the finish.
Cleaning Method:
• Glass cleaner, mild liquid cleaner or nonabrasive scrubbing
pad: Gently clean around the model and serial number plate
because scrubbing may remove numbers.
• All-Purpose Appliance Cleaner Part Number 31662B (not
included):
See "Assistance or Service" section to order.
13
STAINLESS STEEL (on some models)
Cleaning Method:
Rub in direction of grain to avoid damaging.
• Stainless Steel Cleaner & Polish Part Number 31464B (not
included): See "Assistance or Service" section to order.
• Liquid detergent or all-purpose cleaner: Rinse with clean
water and dry with soft, lint-free cloth,
• Vinegar for hard water spots
Do not use soap-filled scouring pads, abrasive cleaners, Cooktop
Polishing Creme, steel-wool pads, gritty washcloths or some
paper towels. Damage may occur.
CERAMIC GLASS (on some models)
Cleaning Method:
Always wipe with a clean, wet cloth or sponge and dry thoroughly
to prevent streaking and staining.
Cooktop Cleaner Part Number 31464B is recommended regularly
to help prevent scratches, pitting and abrasions and to condition
the cooktop, and can be ordered as an accessory. See
"Assistance or Service" section to order.
Cooktop Scraper Part Number RS300 is also recommended for
stubborn soils, and can be ordered as an accessory. See
"Assistance or Service" section to order. The Cooktop Scraper
uses razor blades. Store razor blades out of the reach of
children.
Light to moderate soil
• Paper towels or clean damp sponge:
Clean while the cooktop is still warm. You may want to wear
oven mitts while cleaning the cooktop.
Sugary spills (jellies, candy, syrup)
• Cooktop Scraper: Clean while the cooktop is still warm. You
may want to wear oven mitts while cleaning the cooktop,
Cooktop Polishing Creme and clean damp paper towel:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth, Continue
rubbing until white film disappears.
Heavy soil, dark streaks, specks and discoloration
• Cooktop Polishing Creme or nonabrasive cleanser: Rub
product into soil with a damp paper towel or soft cloth.
Continue rubbing until white film disappears.
Burned-on soil
• Cooktop Cleaner and Cooktop Scraper: Rub creme into soil
with damp paper towel. Hold scraper as flat as possible on
surface and scrape. Repeat for stubborn spots. Polish entire
cooktop with creme and paper towel,
Metal marks from aluminum and copper
• Cooktop Cleaner: Clean as soon as cooktop has cooled
down. Rub creme into surface with a damp paper towel or
soft cloth. Continue rubbing until white film disappears. The
marks will not totally disappear, but after many cleanings they
will become less noticeable,
Tiny scratches and abrasions
• Cooktop Cleaner: Rub creme into surface with a damp paper
towel or soft cloth. Continue rubbing until white film
disappears. Scratches and abrasions do not affect cooking
performance, and after many cleanings they will become less
noticeable.
Do not use steel wool, abrasive powder cleansers, chlorine
bleach, rust remover or ammonia because damage may occur.
COOKTOP CONTROLS
Cleaning Method:
When replacing knobs, make sure knobs are in the Off position,
On some models, do not remove seals under knobs.
• Soap and water or dishwasher: Pull knobs straight away from
control panel to remove.
Do not use steel wool, abrasive cleansers or oven cleaner.
Do not soak knobs.
CONTROL PANEL
Cleaning Method:
• Glass cleaner and soft cloth or sponge: Apply glass cleaner
to soft cloth or sponge, not directly on panel.
• All-Purpose Appliance Cleaner Part Number 31662B (not
included):
See "Assistance or Service" section to order.
Do not use abrasive cleaners, steel-wool pads, gritty washcloths
or some paper towels. Damage may occur.
COIL ELEMENTS (on some models)
Cleaning Method:
• Damp cloth: Make sure control knobs are off and elements
are cool.
Do not clean or immerse in water. Soil will burn off when hot.
For more information, see "Coil Elements and Burner Bowls."
BURNER BOWLS (on some models)
Cleaning Method:
Chrome only
• Solution of 1/2cup (125 mL) ammonia to 1 gal. (3.75 L) water:
Soak for 20 minutes, then scrub with stainless steel-wool
pad.
• Oven cleaner: Follow product label instructions.
• Mildly abrasive cleanser: Scrub with wet scouring pad,
Porcelain enamel only
• Dishwasher
Gas Grate and Drip Pan Cleaner Part Number 31617B (not
included):
See "Assistance or Service" section to order.
SURFACE UNDER COOKTOP (on some models)
For more information, see "Lift-up Cooktop" section.
• Steel-wool pad
Do not remove the cooktop to avoid product damage.
OVEN DOOR EXTERIOR
Cleaning Method:
• Glass cleaner and paper towels or nonabrasive plastic
scrubbing pad: Apply glass cleaner to soft cloth or sponge,
not directly on panel.
• All-Purpose Appliance Cleaner Part Number 31662B (not
included):
See "Assistance or Service" section to order.
14
OVEN CAVITY
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
• Self-Cleaning cycle: See "Self-Cleaning Cycle" first.
Do not use oven cleaners.
OVEN RACKS AND ROASTING RACKS
• Self-Cleaning cycle: See "Self-Cleaning Cycle" first. Remove
racks or they will discolor and become harder to slide. If this
happens, a light coating of vegetable oil applied to the rack
guides will help them slide.
• Steel-wool pad
BROILER PAN AND GRID (on selected models)
Cleaning Method:
Chrome only
• Mildly abrasive cleanser:
Scrub with wet scouring pad.
• Solution of 1/2cup (125 mL) ammonia to 1 gal. (3.75 L) water:
Soak for 20 minutes, then scrub with scouring or steel-wool
pad.
• Oven cleaner: Follow product label instructions.
Porcelain enamel only
• Dishwasher
Do not clean in the Self-Cleaning cycle.
STORAGE DRAWER (on some models)
Make sure drawer is cool and empty before cleaning.
For more information, see "Storage Drawer" section.
• Mild detergent
Drawer Liner (on some models)
Remove all stored items from drawer and lift out drawer liner.
• Clean with mild detergent.
• All-Purpose Appliance Cleaner Part Number 31662B (not
included):
See "Assistance or Service" section to order.
WARMING DRAWER and TRAY (on some models)
Make sure drawer is cool and remove tray.
• Mild detergent (for both)
• All-Purpose Appliance Cleaner Part Number 31662B (not
included):
See "Assistance or Service" section to order.
The oven light is a standard 40-watt appliance bulb. It will come
on when the oven door is open. The oven light will not work
during the Self-Cleaning cycle. On some models, when the oven
door is closed, press the manual oven light switch on the
backguard to turn on and off.
Before replacing, make sure the oven and cooktop are cool and
the control knobs are in the off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
The 120v appliance outlets located on the control console may
be used to run portable appliances placed on countertops beside
the range.
The outlets operate independently and are not affected by range
control settings.
NOTE: Do not place portable appliances on the cooktop.
Damage to the portable appliance could result if the cooktop is
hot.
Appliance Outlet Circuit Breakers:
The circuit breakers for the appliance outlets on your range are
located under the cover on top of the control console. They are
rated for 12 amps.
Lift the cover by lifting the front edge at both ends.
On models equipped with a fluorescent cooktop light, remove the
fluorescent tube to gain access to the circuit breakers.
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is off
and cool. Then, follow these instructions. The oven door is heavy.
Before Removing:
1. Use a putty knife or screwdriver and insert it at the bottom
corner of the door stop clip.
2. Pry door stop clip free and remove from front frame hinge
slot. Be sure not to scratch finish.
3. Repeat procedure for other door stop clip.
To Remove:
1. Open the oven door. Insert door removal pins, included with
your range, into both hinge hangers. Do not remove the pins
while the door is removed from the range.
15
2. Slowly close the door until it rests against the door removal
pins.
3. Grasp the door on the sides with your fingers on the front of
the door and your thumbs on the inside surface.
4. Pull door straight up, then toward you. Hinge hangers will
slide out of front frame hinge slot. Do not remove door
removal pins until the door is replaced on the range.
To Replace:
1.
2.
3.
4.
5.
6.
Insert the door stop clip with the angular surface at the top of
the frame hinge slot, then push in the bottom of the clip until
flanges are flush with the front frame.
Open the door completely and remove the door removal pins.
Save door removal pins for future use.
Close the door.
Grasp the door on the sides with your fingers on the front of
the door and your thumbs on the inside surface.
Hold oven door so that the top edge of each hinge hanger is
horizontal. Insert hinge hangers into the front frame hinge
slots.
Tilt top of door toward range. Slide hinge hangers down onto
front frame support pins. Make sure the hinge hangers are
fully seated and engaged on the support pins.
The storage drawer can be removed. Before removing, make sure
drawer is cool and empty.
To Remove:
1. Pull drawer straight out to the first stop.
2. Lift up the back of the drawer and pull out.
To Replace:
1. Fit the ends of the drawer rails into the guides in the cavity.
2. Slide the drawer closed.
TROL LESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate Cooktop cooking results not what expected
• Is the power supply cord unplugged?
Plug into a grounded outlet.
• Is the proper cookware being used?
See "Cookware" section.
Has a household fuse blown, or has a circuit breaker
tripped?
Replace the fuse or reset the circuit. If the problem continues,
call an electrician.
Cooktop will not operate
• Is the control knob set correctly?
Push in knob before turning to a setting.
• On ceramic glass models, is the "Control Lock" set?
See "Control Lock" section.
Excessive heat around cookware on cooktop
• Is the control knob set to the proper heat level?
See "Cooktop Controls" section.
• Is the appliance level?
Level the appliance. See the Installation Instructions.
Oven will not operate
• Is the electronic oven control set correctly?
See "Electronic Oven Control" section.
• Has a delay start been set?
See "Timed Cooking" section.
• On some models, is the Control Lock set?
See "Control Lock" section.
Is the cookware the proper size?
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1/2"(1.3 cm) outside the cooking area.
Hot Surface indicator light stays on
• Does the Hot Surface indicator light stay on after control
knob(s) have been turned off?
See "Cooktop Controls" section.
Oven temperature too high or too low
• Does the oven temperature calibration need adjustment?
See "Oven Temperature Control" section.
On some models, does the cooling fan run during BAKE,
BROIL or CLEAN?
It is normal for the fan to automatically run when the oven is
in use. This helps cool the electronic control.
16
Oven indicator lights flash
Do the oven indicator lights flash?
See the "Oven Indicator Lights" section. Ifthe indicator
light(s) keeps flashing call for service. See "Assistance or
Service" section.
Display shows messages
Is the display showing "PF" or a flashing time?
There has been a power failure. Clear the display. See
"Display(s)" section. On some models, reset the clock, if
needed. See "Clock" section.
Is the display showing a letter followed by a number?
Depending on your model, press OFF/CANCEL, OFF or
CANCEL/OFF to clear the display. See "Display(s)" section. If
it reappears, call for service. See "Assistance or Service"
section.
Self-Cleaning cycle will not operate
• Is the oven door open?
Close the oven door all the way.
• Has the function been entered?
See "Self-Cleaning Cycle" section.
• On some models, has a delay start Self-Clean cycle been
set?
See "Self-Cleaning Cycle" section.
• Has a delay start been set?
See "Timed Cooking" section.
Oven cooking results not what expected
• Is the appliance level?
Level the appliance. See the Installation Instructions.
• Is the proper temperature set?
Double-check the recipe in a reliable cookbook.
• Is the proper oven temperature calibration set?
See "Oven Temperature Control" section.
• Was the oven preheated?
See "Baking and Roasting" section.
• Is the proper bakeware being used?
See "Bakeware" section.
• Are the racks positioned properly?
See "Positioning Racks and Bakeware" section.
• Is there proper air circulation around bakeware?
See "Positioning Racks and Bakeware" section.
• Is the batter evenly distributed in the pan?
Check to make sure batter is level in the pan.
• Is the proper length of time being used?
Adjust cooking time.
• Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
• Are baked items too brown on the bottom?
Move rack to higher position in the oven.
• Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust and/or
reduce baking temperature.
ASSISTANCEORSERVICE
Before calling for assistance or service, please check
"Troubleshooting." It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
use only factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new INGLIS®appliance.
To locate factory specified parts in your area, call us or your
nearest Whirlpool Canada LP designated service center.
Please call the Whirlpool Canada LP Customer Interaction Centre
toll free: 1-800-807-6777.
Our consultants provide assistance with:
• Features and specifications on our full line of appliances.
• Use and maintenance procedures.
• Accessory and repair parts sales.
Referals to local dealers, repair parts distributors, and service
companies. Whirlpool Canada LP designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to Whirlpool
Canada LP with any questions or concerns at:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
17
INGLIS®COOKTOP,BUILT.INOVENANDRANGEWARRANrY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Canada LP will pay for factory specified parts and repair labor costs to correct defects in
materials or workmanship. Service must be provided by a Whirlpool designated service company.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CLEANTOP ® COOKTOP
On ceramic glass ranges and ceramic glass cooktops, in the second through fifth years from the date of purchase, when this appliance
is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Canada LP will pay for factory
specified parts for the CLEANTOP ®ceramic glass cooktop.
Whirlpool Canada LP warrants that the ceramic glass cooktop will not discolor, the cooktop pattern will not wear off, the rubber seal
between the ceramic glass cooktop and porcelain edge will not crack, the ceramic glass cooktop will not crack due to thermal shock
and the surface unit elements will not burn out,
Whirlpool Canada LP will not pay for:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace household fuses or
correct house wiring, or to replace owner-accessible light bulbs.
2. Repairs when your appliance is used in other than normal, single-family household use.
3. Pickup and delivery. Your appliance is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God or use of products not
approved by Whirlpool Canada LP.
5. Repairs to CLEANTOP ® ceramic glass cooktop if it has not been cared for as recommended in the Use and Care Guide.
6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
7. Replacement parts or repair labor costs for units operated outside Canada.
8. Travel or transportation expenses for customers who reside in remote areas.
9. Any labor costs during the limited warranty period.
WHIRLPOOL CANADA LP SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from province to province.
Outside Canada, this warranty does not apply. Contact your authorized Inglis dealer to determine if another warranty applies.
If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be
found by checking the "Assistance or Service" section or by calling the Whirlpool Canada LP Customer Interaction Centre toll free:
1-800-807-6777.
4/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your appliance to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label/plate, located on your appliance as shown in the
"Parts and Features" section.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
18
P P _,
SECL ITEDELACUISINIERE
Votre s_curit_ et celle des autres est tr_s importante.
Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de
toujours lire tousles messages de securite et de vous y conformer.
Voici le symbole d'alerte de securit6.
Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous
et &d'autres.
Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de deces ou de blessure grave si vous ne
suivez pas immediatement lee instructions.
Risque possible de deces ou de blessure grave si vous
ne suivez pas lee instructions.
Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Dans les conditions de service normales, la cuisiniere ne bascule pas. Elle peut cependant basculer si une force ou un poids excessif
est applique sur la porte ouverte alors que la bride antibasculement n'est pas convenablement fixee.
La bride antibasculement
Le pied de lacuisini_re
Risque de basculement
Un enfant ou une personne adulte peut faire basculer la cuisini_re ce qui peut causer un deces.
Joindre la bride antibasculement au pied arri_re de la cuisiniere.
Joindre de nouveau la bride antibasculement si la cuisiniere est deplacee.
Voir details dans les instructions d'installation.
Le non-respect de ces instructions peut causer un decks ou des brt31ures graves aux enfants et
aux adultes.
Assurez-vous qu'une bride antibasculement est installee :
• Glisser la cuisiniere vers I'avant.
• Verifier que la bride antibasculement est bien fixee au plancher.
• Glisser de nouveau la cuisini_re vers I'arri_re de sorte que le pied est sous la bride
antibasculement.
19
IMPORTANTES INSTRUCTIONS DE SI CURITI
AVERTISSEMENT: Pour reduire le risque d'incendie, de
choc electrique, de blessures ou de dommages Iors de
I'utilisation de la cuisiniere, il convient d'observer certaines
precautions elementaires dont les suivantes :
• AVERTISSEMENT : POUR MINIMISER LE RISQUE
DE BASCULEMENT DE LA CUISINIERE, ELLE DOlT
Ft:TREBIEN IMMOBILISI_E PAR DES DISPOSITIFS
ANTIBASCULEMENT CORRECTEMENT INSTALLI_S.
POUR VI_RIFIER Sl LES DISPOSITIFS SONT
CORRECTEMENT INSTALLI_S, GLISSER LA CUISINIERE
VERS L'AVANT ET VI_RIFIER Sl LA BRIDE
ANTIBASCULEMENT EST BIEN FIXI_E AU PLANCHER,
ETGLISSER LA CUISINIERE VERS L'ARRIERE POUR
QUE LE PIED ARRIERE DE LA CUISINIERE SOIT SOUS
LA BRIDE ANTIBASCULEMENT.
• MISE EN GARDE : Ne pas remiser dans des armoires
au-dessus de la cuisiniere ou sur le dosseret d'une
cuisiniere, des objets que des enfants pourraient vouloir
atteindre. Les enfants pourraient se brt_ler ou se blesser en
grimpant sur la cuisiniere.
• Installation appropriee - S'assurer que la cuisiniere est
correctement installee et reliee #,la terre par un technicien
qualifie.
• Ne jamais utiliser la cuisiniere pour rechauffer ou chauffer
la piece.
• Ne pas laisser les enfants seuls - Les enfants ne doivent
pas 6tre laisses seuls ou sans surveillance dans la piece
ot_ la cuisiniere est en service. Ne jamais laisser les
enfants s'asseoir ou se tenir sur une pattie quelconque de
la cuisiniere.
• Porter des v_tements appropries - Des v_tements amples
ou detaches ne doivent jamais _tre portes pendant
I'utilisation de la cuisiniere.
• Entretien par I'utilisateur - Ne pas reparer ni remplacer
toute piece de la cuisiniere si ce n'est pas specifiquement
recommande darts le manuel. Toute autre operation
d'entretien ou de reparation dolt _tre confiee b,un
technicien qualifie.
• Remisage darts ou sur la cuisiniere - Des materiaux
inflammables ne doivent pas _tre remises dans un four ou
pres des elements de surface.
• Ne pas utiliser d'eau pour eteindre un feu de graisse -
Etouffer le feu ou les flammes ou utiliser un extincteur b,
produits chimiques secs, ou un extincteur & mousse.
• N'utiliser que des mitaines seches de four - Des mitaines
de four mouillees ou humides sur des surfaces chaudes
peuvent provoquer des brQlures provenant de la vapeur.
Ne pas laisser les mitaines de four toucher les elements
chauffants. Ne pas utiliser une serviette ou un tissu epais.
• NE PAS TOUCHER LES ELEMENTS DE SURFACE OU
L'ESPACE PRES DES ELEMENTS - Les elements de
surface peuvent _tre chauds m_me Iorsqu'ils ont une teinte
foncee. Les endroits pres des elements de surface peuvent
devenir assez chauds pour causer des brQlures. Pendant
et apres I'utilisation, ne pas toucher les elements
chauffants et ne pas laisser les v_tements ou autres
materiaux inflammables entrer en contact avec ces
elements de surface ou les endroits pres des elements,
avant qu'ils soient suffisamment refroidis. Ces endroits
comprennent la table de cuisson et les surfaces pres de la
table de la cuisson.
• Utiliser des ustensiles de dimension appropriee - La
cuisiniere est munie d'un ou de plusieurs elements
chauffants de differentes grandeurs. Choisir les ustensiles
qui ont un fond plat assez grand pour couvrir I'element
chauffant de la surface de cuisson. L'utilisation d'ustensiles
trop petits exposera une pattie de I'element chauffant, ce
qui peut provoquer I'inflammation des v_tements.
L'utilisation d'un recipient de dimension correcte ameliore
aussi I'efficacite de la cuisson.
• Ne jamais laisser les elements de la table de cuisson sans
surveillance alors qu'ils chauffent b,la puissance maximale.
II pourrait en resulter une ebullition qui cause de la fumee
et des renversements de corps gras qui peuvent
s'enflammer.
• S'assurer que les cuvettes reflechissantes ou les bols de
renversement sont en place - L'absence de ces cuvettes
ou bols au cours de la cuisson peut causer des dommages
aux ills ou aux composants en dessous des elements.
• Garnissages protecteurs - Ne pas recouvrir les cuvettes
ou le fond du four de papier d'aluminium sauf tel que
suggere dans le manuel. L'installation incorrecte de papier
d'aluminium ou d'autre materiau peut causer un risque de
choc electrique ou d'incendie.
• Ustensiles de cuisson vitrifies - Seulement certains types
d'ustensiles de verre, vitroceramique, ceramique, faYence
ou autres surfaces vitrifiees conviennent pour le service
sur une table de cuisson, sans bris attribuables aux
changements soudains de temperature.
• Les poignees des ustensiles doivent _tre tournees vers
I'interieur et non vers le dessus des elements adjacents -
Pour reduire le risque de brQlures, d'inflammation de
produits inflammables et de renversements dus &
I'entrechoquement non intentionnel des ustensiles, la
poignee d'un ustensile dolt _tre positionnee de sorte
qu'elle est tournee vers I'interieur et non au-dessus des
elements de surface adjacents.
• Ne pas tremper les elements de chauffage amovibles -
Les elements de chauffage ne doivent jamais _tre
immerges dans I'eau.
• Ne pas faire cuire sur une table de cuisson endommagee -
Si la table de cuisson est brisee, les solutions de nettoyage
et les renversements peuvent penetrer darts la table de
cuisson brisee et creer un risque d'un choc electrique.
Contacter immediatement un technicien qualifie.
CONSERVEZ CES INSTRUCTIONS
2O
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Inglis IRE32300 Le manuel du propriétaire
- Catégorie
- Cuisinières
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Inglis IRE32300 Owner's manual