Whirlpool WFG775H0HV Guide d'installation

INSTALLATION INSTRUCTIONS

30" (76.2 CM) FREESTANDING GAS RANGES

INSTRUCTIONS D’INSTALLATION POUR CUISINIÈRES AU

GAZ AUTOPORTANTES DE 30 po (76,2 cm)

INSTRUCCIONES DE INSTALACIÓN ESTUFAS ELÉCTRICAS

INDEPENDIENTES DE 30" (76,2 cm)

W11085334B

Table of Contents

IMPORTANT:

Installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

RANGE SAFETY .............................................................................2

INSTALLATION REQUIREMENTS ................................................. 3

Tools and Parts .............................................................................3

Location Requirements ................................................................4

Electrical Requirements ...............................................................5

Gas Supply Requirements ...........................................................6

INSTALLATION INSTRUCTIONS ................................................... 7

Unpack Range..............................................................................7

Install Anti-Tip Bracket .................................................................8

Make Gas Connection .................................................................8

Install Griddle .............................................................................10

Verify Anti-Tip Bracket Is Installed

and Engaged ..............................................................................11

Level Range ................................................................................11

Electronic Ignition System .........................................................12

Warming Drawer or Premium Storage Drawer ..........................13

Oven Door ..................................................................................14

Complete Installation .................................................................14

GAS CONVERSIONS ....................................................................15

Propane Gas Conversion ...........................................................15

Natural Gas Conversion .............................................................18

2

RANGE SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or death.

– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

– WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch.

•

Do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

– Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of

ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or

unintended operation.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the “What to do if you smell gas” instructions.

3

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

Anti-Tip

Bracket

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

Range Foot

WARNING

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■ Tape measure

■ Flat-blade screwdriver

■ Phillips screwdriver

■ Level

■ Hand or electric drill

■ Hammer

■ Wrench or pliers

■ Pipe wrench

■ 15/16" (24 mm)

combination wrench

■ 1/4" (6.4 mm) drive ratchet

■ 3/8" (95 mm) nut driver

■ 1/8" (3.2 mm) drill bit

(for wood ﬂoors)

■ Marker or pencil

†

®

QUADREX is a registered trademark of NLW Holdings, Inc.

■ Pipe-joint compound

resistant to propane gas

■ Noncorrosive leak-

detection solution

For Propane/Natural

Gas Conversions

■ 3/8" (95 mm) combination

wrench

■ 1/2" (12.7 mm) combination

wrench

■ 5/8" (16 mm) combination

wrench

■ 7 mm (9/32") nut driver

■ Quadrex

®†

or Phillips

screwdriver

■ Masking tape

Parts supplied

Check that all parts are included.

A. Anti-tip bracket

B. #12 x 1

5

⁄

8

" (41.3 mm) screws (2)

■ Anti-tip bracket must be securely mounted to ﬂoor or wall.

Thickness of ﬂooring may require longer screws to anchor

bracket to ﬂoor.

Parts needed

Check local codes and consult gas supplier. Check existing gas

supply and electrical supply. See the “Electrical Requirements”

and “Gas Supply Requirements” sections.

A

B

4

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do

not obstruct ﬂow of combustion and ventilation air.

■ It is the installer’s responsibility to comply with installation

clearances speciﬁed on the model/serial rating plate. The

model/serial rating plate is located on the oven frame behind

the top right side of the oven door.

■ Recessed installations must provide complete enclosure of

the sides and rear of the range.

■ All openings in the wall or ﬂoor where range is to be installed

must be sealed.

■ Do not seal the range to the side cabinets.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The ﬂoor anti-tip bracket must be installed. To install the

antitip bracket shipped with the range, see the “Install Anti-

Tip Bracket” section.

■ Grounded electrical supply is required. See the “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See the

“Gas Supply Requirements” section.

■ Contact a qualiﬁed ﬂoor covering installer to check that the

ﬂoor covering can withstand at least 200°F (93°C).

■ Use an insulated pad or 1/4" (6.4 mm) plywood under range

if installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with

your builder or cabinet supplier to make sure that the materials

used will not discolor, delaminate, or sustain other damage. This

oven has been designed in accordance with the requirements

of UL and CSA International and complies with the maximum

allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD Part 280). When such

standard is not applicable, use the Standard for Manufactured

Home Installations, ANSI A225.1/NFPA 501A or with local codes.

In Canada, the installation of this range must conform with the

current standards CAN/CSA-Z240, latest edition, or with local

codes.

Mobile home installations require:

■ When this range is installed in a mobile home, it must be

secured according to the instructions in this document.

Product Dimensions

A. 27

3

/

8

" (69.5 cm) max. depth with handle

B. 46

1

/

2

" (118.1 cm) overall height (max.) with leveling legs

screwed all the way in*

C. 36" (91.4 cm) cooktop height (max.) with leveling legs

screwed all the way in*

D. 29

7

⁄

8

" (75.9 cm) width

E. 25

5

/

16

" (64.3 cm) depth. Back of range to front of cooktop**

F. Model/serial rating plate (located on the oven frame behind

the top right side of the oven door)

IMPORTANT: Range must be level after installation. Follow the

instructions in the “Level Range” section. Using the cooktop as a

reference for leveling the range is not recommended.

* Range can be raised approximately 1" (2.5 cm) by adjusting

the leveling legs.

** Front of door and drawer may extend farther forward,

depending on styling.

F

D

C

B

E

A

5

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)

countertop depth, 24" (61.0 cm) base cabinet depth and

36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood

combination above the range, follow the range hood or

microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

A. 18" (45.7 cm) upper side cabinet to countertop

B. 13" (33 cm) max. upper cabinet depth

C. 30" (76.2 cm) min. opening width

D. For minimum clearance to top of cooktop, see NOTE*.

E. 30¹⁄

8

" (76.5 cm) min. opening width

F. The shaded areas are recommended for installation of rigid

gas pipe.

G. 11" (27.9 cm)

H. 17" (43.2 cm)

I. 2" (5.1 cm)

J. 4¹⁄

2

" (11.4 cm)

K. 3" (7.6 cm) min. clearance from both sides of range to side

wall or other combustible material.

L. Grounded outlet

M. Cabinet door or hinges should not extend into the cutout.

* NOTE: 24" (61.0 cm) minimum when bottom of wood or

metal cabinet is covered by not less than 1/4" (6.4 mm) ﬂame

retardant millboard covered with not less than No. 28 MSG

sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)

aluminum or 0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the

cooking platform and the bottom of an uncovered wood or

metal cabinet.

Electrical Requirements

IMPORTANT: The range must be electrically grounded in

accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70

or Canadian Electrical Code, CSA C22.1.

This range is equipped with an electronic ignition system that

will not operate if plugged into an outlet that is not properly

polarized.

If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrical installer determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit

is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this range be provided.

■ Electronic ignition systems operate within wide voltage limits,

but proper grounding and polarity are necessary. Check that

the outlet provides 120-volt power and is correctly grounded.

■ This gas range is not required to be plugged into a GFCI

(Ground-Fault Circuit Interrupter) outlet. It is recommended

that you not plug an electric spark ignition gas range or any

other major appliance into a GFCI wall outlet as it may cause

the GFCI to trip during normal cycling.

■ Performance of this range will not be affected if operated

on a GFCI-protected circuit. However, occasional nuisance

tripping of the GFCI breaker is possible due to the normal

operating nature of electronic gas ranges.

■ The wiring diagram is located on the back of the range in a

clear plastic bag.

NOTE: The metal chassis of the range must be grounded in

order for the control panel to work. If the metal chassis of the

range is not grounded, no keypads will operate. Check with

a qualiﬁed electrician if you are in doubt as to whether the

metal chassis of the range is grounded.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

M

H

A

B

C

D

E

L

G

I

K

J

F

6

Gas Supply Requirements

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1, latest edition or CAN/CGA B149, latest

edition.

IMPORTANT: Leak testing of the range must be conducted

according to the manufacturer’s instructions.

Type of Gas

Natural gas:

■ This range is factory set for use with Natural gas. See the

“Gas Conversions” section. The model/serial rating plate

located on the oven frame behind the top right side of the

oven door has information on the types of gas that can be

used. If the types of gas listed do not include the type of gas

available, check with the local gas supplier.

Propane gas conversion:

Conversion must be done by a qualiﬁed service technician.

No attempt shall be made to convert the appliance from the gas

speciﬁed on the model/serial rating plate for use with a different

gas without consulting the serving gas supplier. See the “Gas

Conversions” section.

Gas Supply Line

■ Provide a gas supply line of 3/4" (19 mm) rigid pipe to the

range location. A smaller size pipe on longer runs may

result in insufﬁcient gas supply. With propane gas, piping or

tubing size can be 1/2" (13 mm) minimum. Usually, propane

gas suppliers determine the size and materials used in the

system.

NOTE: Pipe-joint compounds that resist the action of

propane gas must be used. Do not use TEFLON

®†

tape.

†

®

TEFLON is a registered trademark of Chemours.

Flexible metal appliance connector:

■ If local codes permit, a new CSA design-certiﬁed, 4 to

5 ft (122 to 152.4 cm) long, 1/2" (13 mm) or 3/4" (19 mm)

I.D., ﬂexible metal appliance connector may be used for

connecting range to the gas supply line.

■ A 1/2" (13 mm) male pipe thread is needed for connection to

the female pipe threads of the inlet to the appliance pressure

regulator.

■ Do not kink or damage the ﬂexible metal tubing when

moving the range.

Rigid pipe connection:

The rigid pipe connection requires a combination of pipe ﬁttings

to obtain an in-line connection to the range. The rigid pipe must

be level with the range connection. All strains must be removed

from the supply and fuel lines so range will be level and in line.

■ Must include a shut-off valve:

Install a manual gas line shut-off valve in an easily accessible

location. Do not block access to shut-off valve. The valve is

for turning on or shutting off gas to the cooktop.

A. Gas supply line

B. Shut-off valve open position

C. To range

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be

used. The inlet pressure to the regulator should be as follows for

proper operation:

Natural gas:

Minimum pressure: 5" (12.7 cm) WCP

Maximum pressure: 14" (35.5 cm) WCP

Propane gas:

Minimum pressure: 11" (27.9 cm) WCP

Maximum pressure: 14" (35.5 cm) WCP

Contact local gas supplier if you are not sure about the inlet

pressure.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

A

B

C

7

Burner Input Requirements

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft (609.6 m).

For elevations above 2,000 ft (609.6 m), ratings are reduced at

a rate of 4% for each 1,000 ft (304.8 m) above sea level (not

applicable for Canada).

Gas Supply Pressure Testing

Gas supply pressure for testing regulator must be at least

1" (2.5 cm) water column pressure above the manifold pressure

shown on the model/serial rating plate.

Line pressure testing above 1/2 psi (3.5 kPa) gauge

14" (35.6 cm WCP)

The range and its individual shut-off valve must be disconnected

from the gas supply piping system during any pressure testing of

that system at test pressures in excess of 1/2 psi (3.5 kPa).

Line pressure testing at 1/2 psi (3.5 kPa) gauge

14" (35.6 cm WCP) or lower

The range must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

INSTALLATION INSTRUCTIONS

Unpack Range

1. Remove shipping materials, tape and ﬁlm from range.

2. Remove oven racks and parts package from inside oven.

3. Do not remove the shipping base at this time.

A. Shipping base

4. On Ranges Equipped with a Storage Drawer:

Remove the storage drawer. See the “Storage Drawer”

section. Use a 1/4" (6.4 mm) drive ratchet to lower the rear

leveling legs one-half turn. Use a wrench or pliers to lower

front leveling legs one-half turn.

A. 1/4" (6.4 mm) drive ratchet

B. Rear leveling leg

C. Wrench or pliers

D. Front leveling leg

On Ranges Equipped with a Warming Drawer or Premium

Storage Drawer:

On ranges equipped with a warming drawer or premium storage

drawer, the rear legs cannot be accessed by removing the

warming drawer or premium storage drawer. It will be necessary

to adjust the rear legs from outside the range. Use wrench or

pliers to lower the front and rear leveling legs one-half turn.

A. Rear leveling leg

B. Wrench or pliers

C. Front leveling leg

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

A

C

D

A

B

C

A

8

Install Anti-Tip Bracket

1. Remove the anti-tip bracket from where it is taped inside the

storage drawer, warming drawer, or premium storage drawer.

2. Determine which mounting method to use: ﬂoor or wall.

If you have a stone or masonry ﬂoor, you can use the wall

mounting method. If you are installing the range in a mobile

home, you must secure the range to the ﬂoor.

3. Determine and mark centerline of the cutout space. The

mounting can be installed on either the left side or right side

of the cutout. Position mounting bracket against the wall in

the cutout so that the V-notch of the bracket is 12

9

⁄

16

"

(31.9 cm) from centerline as shown.

A. 12

9

⁄

16

" (31.9 cm)

B. Bracket V-notch

4. Drill two 1/8" (3 mm) holes that correspond to the bracket

holes of the determined mounting method. See the following

illustrations.

Floor Mounting

Rear position

Front position Diagonal (2 options)

Wall Mounting

5. Using the Phillips screwdriver, mount anti-tip bracket to

the wall or ﬂoor with the two #12 x 1

5

⁄

8

" (41.3 mm) screws

provided.

6. Move range close enough to opening to allow for ﬁnal

gas and electrical connections. Remove shipping base,

cardboard or hardboard from under range.

7. Move range into its ﬁnal location, making sure rear leveling

leg slides into anti-tip bracket.

8. Move range forward onto shipping base, cardboard, or

hardboard to continue installing the range using the following

installation instructions.

Make Gas Connection

Typical rigid pipe connection

A combination of pipe ﬁttings must be used to connect the

range to the existing gas line. Your connections may be different,

according to the supply line type, size, and location.

1. Apply pipe-joint compound made for use with propane gas

to all pipe thread connections.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Centerline

B

A

9

2. Using a pipe wrench to tighten, connect the gas supply to

the range.

A. Gas pressure regulator

B. 90° elbow (must have 1/2"

(12.7 mm) male pipe thread)

C. Nipple

D. Union

E. Black iron pipe

F. Manual gas shut-off valve

G. 1/2" (12.7 mm) or

3/4" (19.1 mm) gas pipe

H. Nipple

I. Union

J. 90° elbow

Typical ﬂexible connection

1. Apply pipe-joint compound made for use with propane gas

to the smaller thread ends of the ﬂexible connector adapters

(see B and G in the following illustration).

2. Attach one adapter to the gas pressure regulator and

the other adapter to the gas shut-off valve. Tighten both

adapters.

3. Use a 15/16" (23.8 mm) combination wrench and channel

lock pliers to attach the ﬂexible connector to the adapters.

Check that connector is not kinked.

A. Gas pressure regulator

B. Use pipe-joint compound

C. Adapter (must have 1/2"

[12.7 mm] male pipe

thread)

D. Flexible connector

E. Manual gas shut-off valve

F. 1/2" (12.7 mm) or

3/4" (19.1 mm) gas pipe

G. Use pipe-joint compound

H. Adapter

2. Open the manual shut-off valve in the gas supply line. The

valve is open when the handle is parallel to the gas pipe.

A. Closed valve

B. Open valve

3. Test all connections by brushing on an approved

noncorrosive leak-detection solution. If bubbles appear,

a leak is indicated. Correct any leak found.

4. Remove cooktop burner caps and grates from parts

package. Burner caps should be level when properly

positioned. If burner caps are not properly positioned,

surface burners will not light. Place burner grates over

burners and caps.

A. Burner base

B. Burner cap

C. Burner grates

A

B

C

D

E

FG

H

A

B

A

D

EB

C

A. Small

B. X-Large

C. Oval D. Medium

E. Large

Complete Connection

1. Check that the gas pressure regulator shut-off valve is in the

on position.

A. Gas pressure regulator shut-off valve

shown in the on position

A

5. Align the gas tube opening in the burner base with the oriﬁce

holder on the cooktop and the igniter electrode with the

notch in the burner base.

A. Burner cap

B. Gas tube opening

C. Burner base

D. Igniter electrode

E. Oriﬁce holder

A

B

C

D

E

C

A

B

10

7. Plug into a grounded 3 prong outlet.

8. Slide range into ﬁnal location, making sure the rear leveling

leg slides into the slot of the anti-tip bracket.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

6. Place the burner caps on the appropriate burner bases.

IMPORTANT: The bottom of the small and medium caps are

different. Do not put the wrong size burner cap on the burner

base.

Small cap Medium cap

Wok cap

X-Large cap

Burner caps should be level when properly positioned. If burner

caps are not properly positioned, surface burners will not

light. The burner cap should not rock or wobble when properly

aligned.

A. Incorrect

B. Correct

A

B

AUX

SR

UR

Install Griddle

1. Place the "FRONT" end of the griddle down, facing the oven

door. Verify that the lugs are placed onto the grate.

A. Front

B. Lugs

A

B

2. Clean the griddle before using. Refer to the Use and Care

Guide for cleaning instructions. The griddle can be placed

over the left, right, or center burner.

11

Verify Anti-Tip Bracket Is Installed

and Engaged

On Ranges with a Storage Drawer:

1. Remove the storage drawer. See the “Storage Drawer”

section.

2. Use a ﬂashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges with a Warming Drawer or Premium Storage

Drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer or premium storage drawer, and grasp the

lower right or left side of the control panel as shown.

NOTE: If your countertop is mounted with a backsplash, it

may be necessary to grasp the range higher than is shown in

the illustration.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than 1/2" (12.7 mm) off the

ﬂoor without resistance, stop tilting the range and lower it

gently back to the ﬂoor. The range foot is not engaged in the

anti-tip bracket.

IMPORTANT: If there is a snapping or popping sound when

lifting the range, the range may not be fully engaged in the

bracket. Check to see if there are obstructions keeping the range

from sliding to the wall or keeping the range foot from sliding

into the bracket. Verify that the bracket is held securely in place

by the mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the ﬂoor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage

the bracket. Slide the range forward and determine if there

is an obstruction between the range and the mounting wall.

Changes to the gas supply must be performed by a qualiﬁed

service technician. If you need assistance or service, refer to

the “Assistance or Service” section of the Use and Care Guide,

or the cover or “Warranty” section of the User Instructions, for

contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than 1/2" (12.7 mm) off

the ﬂoor without resistance, the anti-tip bracket may not be

installed correctly. Do not operate the range without anti-

tip bracket installed and engaged. Please reference the

“Assistance or Service” section of the Use and Care Guide,

or the cover or “Warranty” section of the User Instructions,

to contact service.

Level Range

Determine if you have AquaLift

®

Technology or Steam Clean by

referring to the “Range Care” section of the User Instructions.

For Ranges with AquaLift

®

Technology or Steam Clean:

1. Place level on the oven bottom as indicated in one of the two

ﬁgures below depending on the size of the level. Check with

the level side to side and front to back.

2. If range is not level, pull range forward until rear leveling leg

is removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

For Ranges without AquaLift

®

Technology or Steam Clean:

1. Place a standard ﬂat rack in oven.

2. Place level on the rack and check levelness of the range, ﬁrst

side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg

is removed from the anti-tip bracket.

4. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

Style 1: Ranges Equipped with a Storage Drawer:

Use a 1/4" (6.4 mm) drive ratchet, wrench or pliers to adjust

leveling legs up or down until the range is level. Push range

back into position. Check that rear leveling leg is engaged in

the anti-tip bracket.

Style 2: Ranges Equipped with a Warming Drawer or

Premium Storage Drawer:

Use a wrench or pliers to adjust leveling legs up or down

until the range is level. Push range back into position. Check

that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking

performance and best cleaning results using AquaLift

®

Technology and Steam Clean functions.

12

Electronic Ignition System

Initial lighting and gas ﬂame adjustments

Cooktop and oven burners use electronic igniters in place of

standing pilots. When the cooktop control knob is turned to the

“LITE” position, the system creates a spark to light the burner.

This sparking continues, as long as the control knob is turned to

“LITE.”

When the oven control is turned to the desired setting, sparking

occurs and ignites the gas.

Check Operation of Cooktop Burners

Standard Surface Burners

Push in and turn each control knob to the “LITE” position.

The ﬂame should light within 4 seconds. The ﬁrst time a burner

is lit, it may take longer than 4 seconds to light because of air in

the gas line.

If burners do not light properly:

■ Turn cooktop control knob to the “OFF” position.

■ Check that the range is plugged in. Check that the circuit

breaker has not tripped or the household fuse has not blown.

■ Check that the gas shut-off valves are set to the “open”

position.

■ Check that burner caps are properly positioned on burner

bases.

Repeat start-up. If a burner does not light at this point, turn

the control knobs to Off and contact your dealer or authorized

service company for assistance.

Adjust Flame Height

Adjust the height of top burner ﬂames. The cooktop "low"

burner ﬂame should be a steady blue ﬂame approximately

1/4" (6.4 mm) high.

A. Low ﬂame

B. High ﬂame

To adjust standard burner:

The ﬂame can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located directly

underneath the control knob.

If the “low” ﬂame needs to be adjusted:

A. Control knob stem

B. Screwdriver

C. Pliers

1. Light one burner and turn to lowest setting.

2. Remove the control knob.

Hold the knob stem with a pair of pliers. Use a small

ﬂatblade screwdriver to turn the screw located in the center

of the control knob stem until the ﬂame is the proper size.

3. Replace the control knob.

4. Test the ﬂame by turning the control from “LO” to “HI,”

checking the ﬂame at each setting.

5. Repeat above steps for each burner.

Check Operation of Oven Bake Burner

1. Remove the oven rack.

2. To remove the oven bottom: Remove two screws at the rear

of the oven bottom. Lift the rear of the oven bottom up and

back until the front of the panel is away from the front frame.

Remove from oven and place on a covered surface.

A. Screws

B. Oven bottom

3. You can check the burner ﬂame by using a mirror.

Insert a mirror to one side of the burner. Look into the mirror

to check ﬂame.

4. Push the BAKE keypad.

5. Push the START keypad.

The oven bake burner should light within 8 seconds. If

unsuccessful, the oven bake burner will pause for 40 seconds

then retry to light for another 8 seconds. It will try for 3 entire

cycles.

Electronic igniters are used to light the bake and broil burners.

Refer to the Use and Care Guide or User Instructions for proper

operation of the oven controls.

Adjust Oven Bake Burner Flame (if needed)

1. On models with a warming drawer, remove access cover

plate (1 screw) located at the back of the warming drawer

compartment.

2. Check the oven bake burner for proper ﬂame.

This ﬂame should have a 1/2" (12.7 mm) long inner cone of

bluish-green, with an outer mantle of dark blue, and should

be clean and soft in character. No yellow tips, blowing or

lifting of ﬂame should occur.

A

B

A

B

C

A

B

13

3. If the oven bake ﬂame needs to be adjusted, locate the

air shutter near the center rear of the range. Loosen the

locking screw and rotate the air shutter until the proper ﬂame

appears. Tighten locking screw.

A. Locking screw

B. Air shutter

4. Push CANCEL/OFF when ﬁnished.

5. Reinstall ﬂame spreader and oven bake burner cover.

Check Operation of Oven Broil Burner

1. Close the oven door.

2. Press the BROIL keypad.

3. Press the START keypad.

The oven burner should light within 8 seconds. If unsuccessful,

the oven bake burner will pause for 40 seconds then retry to

light for another 8 seconds. It will try for 3 entire cycles.

Refer to the Use and Care Guide or User Instructions for proper

operation of the oven controls.

Adjust Oven Broil Burner Flame (if needed)

Look through oven window to check broil burner for proper

ﬂame. This ﬂame should have a 1/2" (12.7 mm) long inner cone

of bluish-green, with an outer mantle of dark blue, and should be

clean and soft in character. No yellow tips, blowing or lifting of

ﬂame should be present.

If ﬂame needs to be adjusted:

1. Loosen the lock screw on the air shutter located at the rear

of the broil burner.

2. Adjust the air shutter as needed.

3. Tighten lock screw.

A. Lock screw

B. Air shutter

4. Press CANCEL/OFF when ﬁnished.

Warming Drawer or Premium Storage

Drawer

(on some models)

Remove all items from inside the warming drawer or premium

storage drawer, and allow the range to cool completely before

attempting to remove the drawer.

To Remove:

1. Open the warming drawer or premium storage drawer to its

fully open position.

2. Using a ﬂat-blade screwdriver, gently loosen the warming

drawer or premium storage drawer from the glide alignment

notch and lift up the drawer alignment tab from the glide.

A. Flat-blade screwdriver

B. Drawer alignment tab

C. Drawer glide notch

3. Repeat Step 2 on the other side. The warming drawer or

premium storage drawer is no longer attached to the drawer

glides. Using both hands, pick up the warming drawer or

premium storage drawer to complete the removal.

To Replace:

1. Align the forward drawer notches with the notches in the

drawer glides on both sides. Place the rear alignment tabs

into the drawer glides on both sides.

A. Drawer alignment tab

B. Drawer glide notch

2. Push the warming drawer or premium storage drawer in all

the way.

3. Gently open and close the warming drawer or premium

storage drawer to ensure it is seated properly on the glides

on both sides.

A

B

A

B

A

B

C

A

B

14

Oven Door

For normal range use, it is not suggested to remove the oven

door. However, if removal is necessary, make sure the oven is

off and cool. Then, follow these instructions. The oven door is

heavy.

To Remove:

1. Open oven door all the way.

2. Pinch the hinge latch between two ﬁngers and pull forward.

Repeat on other side of oven door.

A. Hinge latch

3. Close the oven door as far as it will shut.

4. Lift the oven door while holding both sides.

Continue to push the oven door closed and pull it away from

the oven door frame.

To Replace:

1. Insert both hanger arms into the door.

2. Open the oven door.

You should hear a click as the door is set into place.

3. Move the hinge levers back to the locked position. Check

that the door is free to open and close. If it is not, repeat the

removal and installation procedures.

Complete Installation

1. Check that all parts are now installed. If there is an extra

part, go back through the steps to see which step was

skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See the “Level Range” section.

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, see

the “Range Care” section of the Use and Care Guide or User

Instructions.

6. Read the Use and Care Guide or User Instructions.

7. Turn on surface burners and oven. See the Use and Care

Guide or User Instructions for speciﬁc instruction on range

operation.

If range does not operate, check the following:

■ Household fuse is intact and tight, or circuit breaker has not

tripped.

■ Range is plugged into a grounded 3 prong outlet.

■ Electrical supply is connected.

■ See “Troubleshooting” in the Use and Care Guide or User

Instructions.

8. When the range has been on for 5 minutes, check for heat.

If the range is cold, turn off the range and check that the gas

supply line shut-off valve is open.

■ If the gas supply line shut-off valve is closed, open it,

then repeat the 5-minute test as outlined above.

■ If the gas supply line shut-off valve is open, press

CANCEL on the oven control panel and contact a

qualiﬁed technician.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Use

and Care Guide or the cover of the User Instructions, or contact

the dealer from whom you purchased your range.

A

15

GAS CONVERSIONS

Gas conversions from Natural gas to propane gas or from

propane gas to Natural gas must be done by a qualiﬁed installer.

Propane Gas Conversion

1. Turn the manual shut-off valve to the closed position.

A. To range

B. Manual shut-off valve closed position

C. Gas supply line

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator (Natural Gas to

Propane Gas)

1. Remove storage drawer or warming drawer. See the

“Storage Drawer” or “Warming Drawer or Premium Storage

Drawer” section.

2. Locate gas pressure regulator at rear of storage or warming

drawer compartment.

NOTE: On models with a warming drawer, an access cover

must be removed to access the gas pressure regulator.

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

A

B

C

A

16

3. Remove plastic cover from gas pressure regulator cap.

4. Turn gas pressure regulator cap counterclockwise with a

5/8" (15.9 mm) combination wrench to remove.

NOTE: Do not remove the spring beneath the cap.

A. Plastic cover

B. Gas pressure regulator cap with solid end facing out

C. Gas pressure regulator cap with hollow end facing out

D. Washer

E. Gas pressure regulator cap

5. Turn over the gas pressure regulator cap and reinstall on

regulator so that the hollow end faces out and the marking

“LP” is facing the direction shown in the above drawing.

6. Replace plastic cover over gas pressure regulator cap.

To Convert Surface Burners (Natural Gas to Propane

Gas)

1. Remove burner cap.

2. Using a Phillips or Quadrex

®

screwdriver, remove the burner

base.

NOTE: Reinstall one of the screws through the range

cooktop to hold the oriﬁce spud holder in place while

removing and replacing the oriﬁce spuds.

A. Igniter electrode

B. Gas tube opening

C. Burner cap

D. Burner base

3. Apply masking tape to the end of a 9/32" (7 mm) nut driver

to help hold the gas oriﬁce spud in the nut driver while

changing it. Press nut driver down onto the gas oriﬁce spud

and remove by turning it counterclockwise and lifting out.

Set gas oriﬁce spud aside.

A. Oriﬁce spud

B. Oriﬁce spud holder

C. Screw

D. Spark electrode

4. Remove the cardboard oriﬁce spud holder shipped in

the literature package in the oven. Gas oriﬁce spuds are

stamped with a number, marked with one color dot, and

have a groove in the hex area. Replace the Natural gas

oriﬁce spud with the correct propane gas oriﬁce spud.

A. Propane groove

Refer to the following chart for correct propane gas oriﬁce spud

placement.

Propane Gas Oriﬁce Spud Chart for Surface Burners

Burner

Rating

Color Size (mm) ID

Number

Placement

14,200 BTU Yellow/

Orange

1.16 mm L116 LF

8,000 BTU Yellow/

Black

0.88 mm L88 LR

14,200 BTU Yellow/

Orange

1.16 mm L116 RF

5,000 BTU Yellow/

White

0.70 mm L70 RR

8,000 BTU Yellow/

Black

0.88 mm L88 CTR

NOTE: Refer to the Model Number and Serial Number Plate

located on the oven frame behind the top right side of the oven

door for proper sizing of spuds for each burner location.

5. Place Natural gas oriﬁce spuds in the cardboard oriﬁce spud

holder.

6. Replace the burner base using both screw.

7. Replace burner cap.

8. Repeat steps 1-7 for the remaining burners.

A

B

C

D

Side view before

Side view after

E

NG

LP

NG

LP

A

B

A

C

D

A

B

C

D

QUADREX is a registered trademark of Quadrex Consulting Inc.

17

To Convert Oven Bake Burner (Natural Gas to

Propane Gas)

1. Remove the oven racks and the oven door. See the “Oven

Door” section.

2. Remove two screws and washers at the rear of the oven

bottom.

3. Lift the rear of the oven bottom up and back until the front of

the panel is away from the front frame. Remove from oven

and set it aside on a covered surface.

A. Screws

B. Oven bottom

A

B

7. Replace the “47” spud with a “56” spud. Install the Propane

gas bake burner oriﬁce spud, turning it clockwise until snug.

IMPORTANT: Do not overtighten.

8. Position the back of the bake burner over the oven oriﬁce,

and then align the holes for the screws.

9. Reattach the bake burner with two screws.

10. Position the front of the oven bottom panel toward the front

frame, and then lower the rear of the oven bottom panel into

the oven.

11. Reattach the oven bottom panel with two screws and

two washers.

To Convert Oven Broil Burner (Natural Gas to

Propane Gas)

1. Remove the screw from the broil burner.

2. Remove the ﬂame spreader.

3. Remove the broil burner from the broil burner oriﬁce hood.

NOTE: The broil burner will hang in the back of the oven

while changing the oriﬁce hood.

A. Broil burner

B. Screws

C. Oriﬁce hood

4. Use a 3/8" (9.5 mm) combination wrench and turn the

Natural gas broil burner oriﬁce hood counterclockwise to

remove. The hood will be stamped with a “155.”

A. Oriﬁce spud

A

4. Remove two screws from the bake burner.

5. Slide the front of the bake burner to the side to remove

tab from front of oven. Lift the back of the bake burner off

the oven oriﬁce, and set the bake burner aside. Do not

disconnect the wire.

A. Bake burner

B. Screws

A. Oven oriﬁce

6. Apply masking tape to the end of a 3/8" (9.5 mm) nut driver

to help hold the gas oriﬁce spud in the nut driver while

changing it. Press nut driver down onto the gas oriﬁce spud

and remove by turning the Natural gas bake burner oriﬁce

spud counterclockwise to remove. The spud will be stamped

with a “47.”

A

B

A

B

C

18

5. Replace the “155” hood with a “100” hood. Install the

propane gas broiler burner oriﬁce hood, turning it clockwise

until snug.

IMPORTANT: Do not overtighten.

6. Place the broil burner on the broil burner oriﬁce hood and

insert the broil burner ceramic igniter in the hole in the rear of

the oven.

7. Position the broil burner against the top of the oven and

attach it with two screws.

8. Replace storage drawer or warming drawer. See the

“Storage Drawer” or “Warming Drawer or Premium Storage

Drawer” section.

9. Replace the oven door if it has been removed. See the “Oven

Door” section.

10. Replace the oven racks.

Complete Installation (Natural Gas to Propane Gas)

1. Refer to the “Make Gas Connection” section for properly

connecting the range to the gas supply.

2. Refer to the “Electronic Ignition System” section for proper

burner ignition, operation, and burner ﬂame adjustments.

IMPORTANT: You may have to adjust the “LO” setting for

each cooktop burner.

Checking for proper cooktop, bake and broil burner ﬂame

is very important. The small inner cone should have a very

distinct blue ﬂame 1/4" (6.4 mm) to 1/2" (13 mm) long. The

outer cone is not as distinct as the inner cone. Propane gas

ﬂames have a slightly yellow tip.

3. Refer to “Complete Installation” in the “Installation

Instructions” section of these instructions to complete this

procedure.

NOTE: Make sure to save the oriﬁces that have just been

replaced in the conversion.

Natural Gas Conversion

1. Turn the manual shut-off valve to the closed position.

A. To range

B. Manual shut-off valve closed position

C. Gas supply line

2. Unplug range or disconnect power.

To Convert Gas Pressure Regulator (Propane Gas to

Natural Gas)

1. Remove storage drawer or warming drawer. See the

“Storage Drawer” or “Warming Drawer or Premium Storage

Drawer” section.

2. Locate gas pressure regulator at rear of storage or warming

drawer compartment.

NOTE: On models with a warming drawer, an access cover

must be removed to access the gas pressure regulator.

A. Gas pressure regulator

IMPORTANT: Do not remove the gas pressure regulator.

x.xx

A

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation

instructions.

Slide range back so rear range foot is engaged in the

slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed

and engaged.

Failure to follow these instructions can result in death

or serious burns to children and adults.

A

B

C

A

19

3. Remove plastic cover from gas pressure regulator cap.

4. Turn gas pressure regulator cap counterclockwise with a

5/8" (15.9 mm) combination wrench to remove.

NOTE: Do not remove the spring beneath the cap.

A. Plastic cover

B. Gas pressure regulator cap with hollow end facing out

C. Gas pressure regulator cap with solid end facing out

D. Washer

E. Gas pressure regulator cap

5. Turn over the gas pressure regulator cap and reinstall on

regulator so that the solid end faces out and the marking

“NG” is facing the direction shown in the above drawing.

6. Replace plastic cover over gas pressure regulator cap.

To Convert Surface Burners (Propane Gas to Natural

Gas)

1. Remove burner cap.

2. Using a Phillips or Quadrex

®

screwdriver, remove the burner

base.

NOTE: Reinstall one of the screws through the range

cooktop to hold the oriﬁce spud holder in place while

removing and replacing the oriﬁce spuds.

3. Apply masking tape to the end of a 9/32" (7 mm) nut driver

to help hold the gas oriﬁce spud in the nut driver while

changing it. Press nut driver down onto the gas oriﬁce spud

and remove by turning it counterclockwise and lifting out.

Set gas oriﬁce spud aside.

A. Oriﬁce spud

B. Oriﬁce spud holder

C. Screw

D. Spark electrode

4. Gas oriﬁce spuds are stamped with a number on the side.

Replace the propane gas oriﬁce spud with the correct

Natural gas oriﬁce spud.

A. Stamped number

Burner

Rating

Color Size (mm) ID

Number

Placement

18,000 BTU Red/

Black

2.00 mm N216 LF

9,500 BTU Red/

White

1.40 mm N210 LR

15,000 BTU Red/

Yellow

1.80 mm N200 RF

5,000 BTU Blue/

White

1.04 mm N190 RR

8,000 BTU Red/

White

1.40 mm N185 CTR

Refer to the following chart for the correct Natural gas oriﬁce

spud placement.

Natural Gas Oriﬁce Spud Chart

NOTE: Refer to the Model Number and Serial Number Plate

located on the oven frame behind the top right side of the oven

door for proper sizing of spuds for each burner location.

5. Place propane gas oriﬁce spuds in plastic parts bag for

future use and keep with package containing literature.

6. Replace the burner base using both screws.

7. Replace burner cap.

8. Repeat steps 1-7 for the remaining burners.

To Convert Oven Bake Burner (Propane Gas to

Natural Gas)

1. Remove the oven racks and the oven door. See the “Oven

Door” section.

2. Remove two screws and washers at the rear of the oven

bottom.

3. Lift the rear of the oven bottom up and back until the front of

the panel is away from the front frame. Remove from oven

and set it aside on a covered surface.

A. Screws

B. Oven bottom

A

B

A

B

C

D

Side view before

Side view after

E

NG

LP

NG

B

A

C

D

XXX

A

20

4. Remove two screws from the bake burner.

5. Slide the front of the bake burner to the side to remove

tab from front of oven. Lift the back of the bake burner off

the oven oriﬁce, and set the bake burner aside. Do not

disconnect the wire.

A. Bake burner

B. Screws

A. Oven oriﬁce

6. Apply masking tape to the end of a 3/8" (9.5 mm) nut driver

to help hold the gas oriﬁce spud in the nut driver while

changing it. Press nut driver down onto the gas oriﬁce spud

and remove by turning the propane gas bake burner oriﬁce

spud counterclockwise to remove. The spud will be stamped

with a “56.”

7. Replace the “56” spud with a “47” spud. Install the Natural

gas bake burner oriﬁce spud, turning it clockwise until snug.

IMPORTANT: Do not overtighten.

A. Oriﬁce spud

8. Position the back of the bake burner over the oven oriﬁce,

and then align the holes for the screws.

9. Reattach the bake burner with two screws.

10. Position the front of the oven bottom panel toward the front

frame, and then lower the rear of the oven bottom panel into

the oven.

11. Reattach the oven bottom panel with two screws and

two washers.

A

B

A

La page charge ...

Whirlpool WFG775H0HV Guide d'installation

Whirlpool WFG775H0HV Guide d'installation

dans d''autres langues

Documents connexes

Autres documents