GE GDF535PGRWW Mode d'emploi
- Catégorie
- Lave-vaisselle
- Taper
- Mode d'emploi
FOR YOUR SAFETY
Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
While performing installations described in this booklet,
gloves, safety glasses or goggles should be worn.
IMPORTANT – Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these instructions
for the consumer’s and local inspector’s use.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliances Warranty.
See warranty information.
• Completion Time – 1 to 3 Hours. New installations
require more time than replacement installations.
IMPORTANT – The dishwasher MUST be installed to
allow
for future removal from the enclosure if service is required.
Care should be exercised when the appliance is installed
or removed,
to reduce the likelihood of damage to the
power supply cord.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
Your dishwasher is a water heating appliance.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• Remove all power leading to the appliance from the
circuit breaker or fuse box before beginning installation.
Failure to do so can result in a risk of electrical shock.
•
To reduce the risk of electric shock, fire, or injury to persons,
the installer must ensure that the dishwasher is completely
enclosed at the time of installation.
• The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt that the appliance is properly
grounded. If house wiring is not 2-wire with ground, a
ground must be by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
•
To reduce the risk of electric shock, fire, or injury to persons,
the installer should check to ensure that wires are not pinched
or damaged, the house wiring is attached to the junction box
bracket through a strain relief, and all electrical connections
made at the time of install (wire nuts) are contained inside of
the junction box cover.
WARNING
• Retire todos los conductores de corriente del
electrodoméstico de disyuntor o de la caja del fusible
antes de comenzar con la instalación. Si no cumple con
esto, se podrá producir el riesgo de descargas eléctricas.
• Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador debe asegurarse
de que el lavaplatos esté completamente cerrado en
el momento de la instalación.
• La conexión inadecuada del conductor de conexión a
tierra del equipamiento puede provocar un riesgo de
descarga eléctrica. Consulte a un electricista calificado
o representante de servicio técnico si tiene dudas
sobre la correcta conexión a tierra del aparato. Si el
cableado doméstico no cuenta con un cable de 2 hilos
con conexión a tierra, un instalador debe realizar una
conexión a tierra. Cuando el cableado doméstico es de
aluminio, asegúrese de usar un compuesto antioxidante
y conectores de aluminio a cobre aprobados por UL.
• Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador deberá realizar un
control para asegurar que los cables no estén pellizcados
ni dañados, que el cableado del hogar esté conectado a la
ficha de la caja de empalmes a través de un amortiguador
de refuerzo, y que todas las conexiones eléctricas
realizadas en el momento de la instalación (tuercas para
cables) estén dentro de la tapa de la caja de empalmes.
ADVERTENCIA
See your Owner’s Manual for details on how to contact us regarding installation questions
Built-In DishwashersInstallation Instructions
31-4000220 Rev 1 08-20 GEA
Opening the door will cause the
dishwasher to tip forward when it is
not fully installed. When opening the door prior to the
dishwasher being fully installed, hold the top of the
dishwasher securely with one hand and hold the door
with the other hand. Gloves should be worn.
CAUTION
Abrir la puerta hará que el
lavavajillas se incline hacia
adelante cuando no se encuentre completamente
instalado. Al abrir la puerta antes de haber instalado
completamente el lavavajillas, sostenga la parte superior
del lavavajillas de forma segura con una mano y sostenga
la puerta con la otra mano. Se deberán usar guantes.
PRECAUCIÓN
READ CAREFULLY
KEEP THESE INSTRUCTIONS
PARTS SUPPLIED IN
INSTALLATION PACKAGE:
• Junction box cover
• #10 hex-head screw
• Hose clamp
• Drain hose hanger
• 2 Plug buttons
• Toekick (pre-installed on some models)
• 2 Tub trim pieces (on some models)
• 2 Mounting brackets for wood countertops
or side cabinets
• 2 #8-18 x 5/8” Phillips special head screws,
to secure dishwasher to underside of
countertop or to side cabinets
• Insulation pieces (on some models)
• Literature, samples and/or coupons
TOOLS YOU WILL NEED:
• Phillips-head screwdriver
• 1/4” and 5/16” nutdriver
• 6” Adjustable wrench
• Level
• Carpenter’s square
• Measuring tape
• Safety glasses
• Flashlight
• Bucket to catch water when flushing the line
• 15/16” socket
• Gloves
• Pliers
For New Installations Only:
• Tubing cutter
• Drill and appropriate bits
• Hole saw set
MATERIALS YOU WILL NEED:
• ´*+7*DUGHQ+RVH7KUHDGÛHOERZLQFOXGLQJ
gasket) - with opposite end sized to fit Hot Water Line
• Thread seal tape
• UL-listed wire nuts (3)
• Masking tape
Materials For New Installations Only:
• Air gap for drain hose, if required
• Waste tee for house plumbing, if applicable
• Electrical cable or Power Cord Kit WX09X70910 (5’ 5” long)
or WX09X70911 (7’ 11” long) depending on installation.
• Strain relief for electrical connection
• Hose clamps
• Hand shut-off valve (recommended)
• Hot Water Line–3/8” minimum, copper tubing (including
ferrule, compression nut) or GE Appliances Part #
WX28X326, flexible braided hose.
• WD24X10065 drain hose (12’ long) or WD24X10062
drain hose (4’ long), if needed.
Installation Preparation
2
Hole Saw Set
Tubing Cutter
Drill and Bits
Phillips-Head
Screwdriver
15/16” Socket
1/4” and 5/16”
Nutdriver
Bucket
Flashlight
Gloves
Carpenter’s
Square
Safety Glasses
Level
Hose Clamp
Junction
Box Cover
#10
Hex-Head
Junction
Box Screw
3/8" long
Mounting
Brackets
#8 Phillips
Special
Head Screws
5/8" long
Literature
Insulation
(on some models)
Tub Trim Pieces
(on some models)
Pliers
Strain
Relief
Optional -
12' Drain Hose - WD24X10065
4’ Drain Hose - WD24X10062
Hot
Water
Line
Waste Tee
Electrical Cable
(or Power Cord,
if applicable)
Wire Nuts (3)
GHT 90°Elbow
Hand
Shut-Off
Valve
Air Gap
Plug
Buttons
Masking Tape
Toekick
Drain Hose Hanger
Thread
Seal Tape
(if applicable)
6” Adjustable
Wrench
Hose
Clamps
Measuring Tape
PREPARE DISHWASHER ENCLOSURE
• The rough cabinet opening must be at least 24” deep,
24” wide and approximately 34-1/2” high from floor to
underside of the countertop.
• The dishwasher must be installed so that drain hose is
no more than 16’ in length for proper drainage.
• The dishwasher must be fully enclosed on the top,
sides and back, and must not support any part of the
enclosure.
CLEARANCES: When installed into
a corner, allow 2” min. clearance
between dishwasher and adjacent
cabinet, wall or other appliances.
Allow 25-1/2” min. clearance from
the front of the dishwasher for
door opening.
34-1/2”+1/4”
Underside of
Countertop
to Floor
This Wall Area
Must be Free
of Pipes and
Wires
Cabinets
Square
and
Plumb
Plumbing and Electric Service
Must Enter Inside This Area
24”
Min.
4”
6”
24”
Min.
33-1/2” to 34-3/4”
Underside of
Countertop
to Floor
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 16’ distance to drain.
NOTE : Air gap must be used if waste tee or disposer
connection is less than 18” above floor to prevent siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
• Do local codes or ordinances require an air gap?
• Is waste tee less than 18” above floor?
If the answer to either question is YES, Method 1
MUST be used.
•
If the answers are NO, either method may be used.
CABINET PREPARATION
• Drill a 1-1/2” diameter hole in the cabinet wall within
the shaded areas shown in PREPARE DISHWASHER
ENCLOSURE section for the drain hose connection.
The hole should be smooth with no sharp edges.
IMPORTANT – When connecting
drain line to disposer, check to be sure
that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF
PLUG IS LEFT IN PLACE.
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes
and ordinances. The air gap must be installed according
to manufacturer’s instructions.
Tip: Avoid unnecessary service call charges.
Always be sure disposer drain plug has been removed
before attaching dishwasher drain hose to the disposer.
3
Clearance for Door
Opening 2" Minimum
Countertop
Dishwasher
25-1/2"
Remove
Drain
Plug
Installation Preparation
To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher
is completely enclosed at the time of installation.
WARNING
Method 2 – “High Drain Loop” with Waste Tee or Disposer
Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador debe asegurarse
de que el lavaplatos esté completamente cerrado en el
momento de la instalación.
ADVERTENCIA
DISHWASHER HANDLE DIMENSION: The dishwasher
door should be flush with the cabinet. For models with
a handle, the total depth (with handle) is 26-1/4” max.
depending on the model. Locate the Quick Specs document
online for more dishwasher dimensions.
72”
max.
72”
max.
Drain Hose Hanger
18”
min.
32” min. -
72” max.
Drain Hose Hanger
18”
min.
32” min. -
72” max.
Installation Preparation
Cabinet Preparation & Wire Routing
•
The wiring may enter the opening from either side, rear
or the floor within the shaded area illustrated above
in figure and defined in PREPARE DISHWASHER
ENCLOSURE section.
• Cut a 1-1/2" maximum diameter hole to admit the
electrical cable. Edges of hole should be smooth and
rounded. Permanent wiring connections may pass
through the same hole as the drain hose and hot water
line, if convenient. If cabinet wall is metal, the hole
edge must be covered with a bushing.
NOTE:
Power cords with plug must pass through a
separate hole in the cabinet.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
• For permanent connections the cable must be routed
as shown in figure. Cable must extend a minimum of
24" from the rear wall.
• For power cord connections, install a 3-prong
grounding type receptacle in the sink cabinet rear wall,
6" min. or 18" maximum from the opening, 6" to 18"
above the floor.
• Use only WX09X70910 (5’ 5” long) or WX09X70911 (7’
11” long) Dishwasher Power Cord Kit. Do not use an
extension cord or adapter plug with this appliance.
PREPARE ELECTRICAL WIRING
4
White
18"
6"
24"
from Wall
3"
from
Cabinet
Alternate Receptacle
Location in Adjacent
Cabinet
Ground
Black
1-1/2" Dia. Hole (Max.)
18"
6"
Receptacle
Location
Area
Retire todos los conductores de
corriente del electrodoméstico
de disyuntor o de la caja del fusible antes de comenzar
con la instalación. Si no cumple con esto, se podrá
producir el riesgo de descargas eléctricas.
ADVERTENCIA
Remove all power leading to the
appliance from the circuit breaker or
fuse box before beginning installation. Failure to do so
can result in a risk of electrical shock.
WARNING
La conexión inadecuada del
conductor de conexión a
tierra del equipamiento puede provocar un riesgo de
descarga eléctrica. Consulte a un electricista calificado
o representante de servicio técnico si tiene dudas sobre
la correcta conexión a tierra del aparato. No modifique el
enchufe que se suministra con el aparato; si no calza en el
tomacorrientes, haga que un técnico calificado le instale
un tomacorrientes adecuado.
ADVERTENCIA
The improper connection of the
equipment grounding conductor can
result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt that
the appliance is properly grounded. Do not modify the plug
provided with the appliance; if it will not fit the outlet, have
a proper outlet installed by a qualified technician.
WARNING
ELECTRICAL REQUIREMENTS
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electric Code, ANSI/
NFPA
70 – latest edition, and all local codes and ordinances.
This appliance must have:
• 120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused
electrical supply.
•
Wiring must be 2 wire with ground and rated for 75°C (167°F).
• If the electrical supply does not meet the above
requirements, call a licensed electrician before proceeding.
It is recommended to have:
• A circuit breaker or time-delay fuse.
• A properly grounded individual branch circuit.
Grounding Instructions–Permanent Connection
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and be
connected to the
equipment-grounding terminal or lead on
the appliance.
Grounding Instructions–Power Cord Models
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must
be plugged into an appropriate outlet
that is installed and grounded in accordance with all local
codes and ordinances.
Con los modelos equipados
con cable de corriente: No
modifique el enchufe provisto con el electrodoméstico;
si no coincide con el tomacorriente, solicite la instalación
de un tomacorriente apropiado a un electricista
calificado.
ADVERTENCIA
For models equipped with power
cord: Do not modify the plug
provided with the appliance; if it will not fit the outlet,
have a proper outlet installed by a qualified technician.
WARNING
Water Line Connection
• If using a flexible braided supply hose, label
the hose with the installation date to use as
reference. Flexible braided hoses, elbows and
gaskets should be replaced in 5 years.
• Turn off the water supply.
• Install a hand shut-off valve in an accessible
location, such as under the sink. (Optional, but
strongly recommended and may be required by local
codes.)
• Water connection is on the left side of the
dishwasher. Install the hot water inlet line, using no
less than 3/8” copper tubing or a flexible braided
hose. Route the line as shown in PREPARE HOT
WATER LINE section and extend forward at least
19” from rear wall.
• Adjust water heater for 120°F to 140°F temperature.
• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120
PSI.
Turn page to begin dishwasher installation.
Installation Preparation
PREPARE HOT WATER LINE
NOTE: We recommend copper tubing for the water
line, but if you choose to use flexible hose, use GE
Appliances WX28X326, flexible braided hose.
• The water supply line (3/8” copper tubing or flexible
braided hose) may enter from either side, rear or
floor within the shaded area shown in figure.
• The water supply line may pass through the same
hole as the electrical cable and drain hose. Or, cut
an additional 1-1/2" diameter hole to accommodate
the water line. If power cord with plug is used, water
line must not pass through power cord hole.
6"
4"
Cabinet Face
Shut-off
Valve
2" From Floor
19" From Wall
2"
From
Cabinet
Hot
1-1/2”
Dia.
Hole
5
STEP 1
PREPARATION
Locate the items in the installation package:
• Screws
• Junction box cover
• Drain hose and clamp
• Mounting brackets
• Trim pieces (on some models)
• Drain hose hanger
• Insulation pieces (some models)
• Toekick (pre-installed on some models)
• Owner’s Manual
• Product samples and/or coupons
Dishwasher Installation
STEP 2
CHECK DOOR BALANCE
(CONT.)
CHECK DOOR BALANCE
To check the door balance, hold the top of the
dishwasher firmly.
• Check the door balance by opening and closing the
door.
6
STEP 2
Tip: Make sure door opens and closes smoothly.
Check door opening and closing. If door does not open
easily or falls too quickly, check spring cable routing.
The cable is held in place by “shoulders” on the pulley.
Check to be sure cable has not slipped over the pulley
shoulders and is routed as shown.
Make sure
pulley cable
is within
pulley
shoulders
Front View
Opening the door will cause the
dishwasher to tip forward when it is
not fully installed. When opening the
door prior to the dishwasher being
fully installed, hold the top of the
dishwasher securely with one hand and hold the door
with the other hand. Gloves should be worn.
CAUTION
Abrir la puerta hará que el lavavajillas
se incline hacia adelante cuando
no se encuentre completamente
instalado. Al abrir la puerta antes de
haber instalado completamente el
lavavajillas, sostenga la parte superior del lavavajillas
de forma segura con una mano y sostenga la puerta
con la otra mano. Se deberán usar guantes.
PRECAUCIÓN
• Door is properly
balanced if,
when opened, it
self closes within
20° from vertical,
stays in position
from 20° to 70°
and falls fully
open beyond 70°.
• If necessary
increase or
decrease tension
as shown. Latch
door and adjust
left spring tension on the side of the dishwasher to
correct balance. You will need to use a screwdriver to
knock out the adjustment holes on the rail.
NOTE: The right side spring is not adjustable.
Door
closes
within
20°
Door stays in
position from
20° to 70°
Door falls fully
open beyond 70°
Side View
Increase
Tension
Decrease
Tension
Side
View
STEP 5
POSITION WATER LINE
AND HOUSE WIRING
• Position water supply line and house wiring on the
floor of the opening to avoid interference with base
of dishwasher and components under dishwasher.
STEP 6
INSTALL DRAIN HOSE,
THROUGH CABINET
• Position dishwasher in front of cabinet opening.
Insert drain hose into the hole in cabinet side. If
a power cord is used, guide the end through a
separate cabinet opening.
Tip: Prevent unnecessary service call charges for
fill, drain or noise concerns.
Position utility lines so they do not interfere with
anything under or behind the dishwasher.
Reposition the insulation blanket over the collar, as
shown.
Dishwasher Installation
Water
Line
House
Wiring
4"
4"
6"
6"
7
STEP 4
INSTALL 90° ELBOW
• Thread 3/4” GHT 90°
elbow onto the water
valve. Ensure rubber
gasket is located
between valve and
elbow.
• Do not overtighten
elbow. Water valve
bracket could bend or
water valve fitting could
break.
• Position the end of the
elbow to face the rear
of the dishwasher.
Water
Valve
Bracket
Fill Hose
Front of dishwasher
90° Elbow
House
Wiring
Power Cord
(If used)
Drain
Hose
Water
Line
Insulation
Blanket
Ensure drain hose is not
twisted or pinched
Maximum drain hose
length is 16' from the
rear of the dishwasher
Do not disconnect or remove high
drain loop from left side of dishwasher
Pull insulation
blanket over
collar
STEP 3
ADJUST LEVELING LEGS
• Move the dishwasher close to the installation location
and lay it on its back. NOTE: Do not place the
dishwasher on its side.
• Discard base.
• With 15/16” socket wrench adjust leveling legs into
the dishwasher frame, approximately 1/2” from frame
as shown.
Approx.
1/2”
Dishwasher Installation
SLIDE DISHWASHER
THREE-FOURTHS OF
THE WAY INTO CABINET
IMPORTANT – Do not push against front panel with
knees. Damage will occur.
•
Grasp the sides of the front panel and slide
dishwasher into the opening a few inches at a time.
• As you proceed, pull the drain hose through the
opening under the sink. Stop pushing when the
dishwasher extends about 6 inches forward of
adjacent cabinets.
• Make sure drain hose is not kinked under or behind
the dishwasher.
• Make certain the house wiring, drain line and
water line do not interfere with components under
dishwasher.
STEP 7
Do not push against
front door panel with
knee. Damage to the
door panel will occur.
8
INSTALL TRIM PIECES
In this step you will need the trim pieces set aside in Step 1.
• Select the top trim piece and line up center to the
top latch. Press the trim piece onto the tub flange
moving from one side to the other.
• Select the left trim piece. Align top edge with the top
trim and press it onto the left side of the tub flange
moving from the top to the bottom. Repeat for the
right side tub flange trim piece.
Top
View
Handle
Door
Tub trim
Tub frame
STEP 8
Side Trim
Side
Trim
Top View
Side
Trim
Top Trim
(on some models)
Fully seat to tub flange
Dishwasher Installation
9
INSTALL MOUNTING
BRACKETS
You will need the mounting brackets set aside in
Step 1.
You must install the mounting brackets onto the
dishwasher tub frame top OR sides prior to sliding the
dishwasher into place under the countertop.
Install mounting brackets on top if the
underside of countertop is wood or wood-like
material that accepts screws:
Install the brackets by inserting the tabs through the
slots on the tub frame as shown. NOTE: You may
need to work the tabs through the slots.
Using pliers, bend and twist the tabs upward to secure
as shown.
IMPORTANT - After installing brackets and before
closing the dishwasher door, adjust the brackets
by bending them up as needed, so that they do not
contact the top of the dishwasher door and cause
damage.
•
If you are installing the dishwasher under a counter
with a short overhang, the countertop brackets may
extend beyond the edge of the counter. If this is
the case, remove the excess length by repeatedly
bending the brackets at the front notch only until they
break.
PUSH DISHWASHER INTO
FINAL POSITION
•
Check the tub insulation blanket, if equipped, to be
sure it is smoothly wrapped around the tub. It should
not be “bunched up” and it must not interfere with
the door springs. If the insulation is “bunched up” or
interfering with the springs, straighten and re-center
the blanket prior to sliding the dishwasher into its
final position.
•
Slide the dishwasher into the final position by
pushing on the sides of the door panel. Do not push
or pull the door in a partially open or closed position
when moving the dishwasher. Do not use a knee or
push on the center of the panel. If you do, damage
to the panel will likely result.
•
The dishwasher is in the final position when the
edges of the front panel are flush with the adjacent
cabinets and the dishwasher is centered in the
cabinet opening. Check that the dishwasher is
squarely positioned in the cabinet opening at both
the top and the bottom of the appliance prior to
mounting to the cabinet.
IMPORTANT – Before opening the dishwasher door,
be certain the edges of the dishwasher door panel are
behind the face of the adjacent cabinet and not up
against the cabinet face. Refer to figure below. If the
dishwasher door is opened when the edge of the door
is against the face of the cabinet, dishwasher door
damage and cabinet damage will occur.
STEP 9
INSTALL MOUNTING
BRACKETS (CONT.)
Install mounting brackets on sides if the
countertop is granite or similar material that
will not accept wood screws:
• Break off front portion of the bracket with pliers at the
location shown prior to attaching to dishwasher.
• Install the brackets by inserting the tabs through the
slots on the tub frame as shown. NOTE: You may
need to work the tabs through the slots.
Using pliers, bend and twist the tabs to secure as
shown.
STEP 9
STEP 10
Top
Mounting
Insert the bracket tabs
into the tub slots
Using pliers,
bend and
twist the
tabs
upward
to secure
Bracket
Bend and break here
after installing if
counter has a short
overhang.
Tub Frame
Side Mounting
Bend and break
here as necessary
Insert the
bracket
tabs into
the tub
slots
Using pliers,
bend and twist
the tabs upward to
secure
Bracket
Tub Frame
Dishwasher Installation
PUSH DISHWASHER
INTO FINAL POSITION
(CONT.)
•
Check dishwasher alignment prior to opening
dishwasher door to prevent panel damage.
•
Open and close the dishwasher door to be sure it
operates smoothly, and does not rub on the adjacent
cabinet.
Tip: Prevent unnecessary service charges for
panel damage or wash performance.
Make sure utility lines are not trapped or crushed behind
dishwasher. Crushed lines will restrict water flow.
LEVEL DISHWASHER
IMPORTANT – Dishwasher must be level for proper
dish rack operation, wash performance and door
operation. The dishwasher must be leveled left to right
and front to back. This ensures the dish racks will not
roll in or out on their own, circulation water will flow to
the pump inlet, and the door will close without hitting
the side of the tub.
•
Remove the lower dish rack and place a level on the
door and lower rack track as shown in figure.
•
Adjust the level of the dishwasher by individually
turning the 4 legs on the bottom of the dishwasher as
shown. Ensure all 4 legs are firmly in contact with the
floor.
• The dishwasher is properly leveled when the level
indicator is centered left to right and front to back.
Also, the dishwasher door should close without hitting
the side of the tub.
• Replace the lower rack.
Tip: Prevent unnecessary service charges. Verify
dishwasher is leveled.
Pull the dish racks half way out. They should stay put.
Open and close the door. The door should fit in the
tub opening without hitting the side of the tub. If the
racks roll on their own, or the door hits the side of tub,
re-level the dishwasher.
10
STEP 10 STEP 11
Check that tub trim does not
contact the door at all points
Tub trim may be trimmed if
necessary to ensure proper
door operation
Top
View
Handle
Door
Tub trim
Tub frame
Do not allow tub trim to get
trapped by or come into
contact with the door
Top
View
Tub trim
trapped
by door!
Cabinet
Turn Legs
to Adjust
Correct
Alignment
Door
Fits and
Swings
Back
Behind
Cabinet
Frame
Door Catches
on Cabinet Frame
Incorrect Alignment
will result in door damage
Dishwasher Installation
11
POSITION DISHWASHER,
SECURE TO COUNTERTOP
OR CABINET
In this step you will need the 2 Phillips special head
screws from the screws set aside in Step 1.
The dishwasher must be secured to the countertop or
the cabinet sides. When the underside of the countertop
is wood, use Method 1. Use Method 2 when the
underside of the countertop is made of a material, such
as granite, that will not accept wood screws.
IMPORTANT – Prevent door panel and control
panel damage. Dishwasher must be positioned so
the front panel and control panel do not contact the
adjacent cabinets or countertop. The unit should be
centered between the 2 cabinets. Mounting screws
must be driven straight and flush. Protruding screw
heads could scratch the door panel or control panel
and interfere with door operation.
Method 1
Secure dishwasher to underside of wood countertop.
• Re-check alignment of the dishwasher in the cabinet.
Refer to Steps 12 and 13. Door panel and/or control
panel must not hit cabinets or countertop.
• Fasten the dishwasher to the underside of the
countertop with the 2 Phillips special head screws.
Refer to figure. Make certain screws are driven
straight and flush to prevent panel damage.
• Plug buttons must be installed to ensure proper door
to tub alignment. Install plug buttons to the side of the
tub well in the holes provided.
Method 2
Secure dishwasher to cabinet sides.
• Recheck alignment of the dishwasher in the cabinet.
Refer to Steps 12 and 13. Door panel and/or control
panel must not hit cabinets or countertop.
• Fasten the dishwasher to the adjacent cabinets with
the 2 Phillips special head screws provided. Refer to
figure. Make certain screws are driven straight and
flush to prevent panel damage. Do not screw into
the cabinet face frame.
• Plug buttons must be installed to ensure proper door
to tub alignment. Install plug buttons to the side of
the tub in the holes provided.
CONNECT WATER
SUPPLY
Connect water supply line to 90° elbow.
If using a flexible braided hose connection:
• Attach nut to 90° elbow using an adjustable wrench.
If using a copper tubing connection:
•
Slide compression nut, then ferrule over end of water
line.
• Insert water line into 90° elbow.
•
Slide ferrule against elbow and secure with
compression nut.
IMPORTANT – Check to be sure that door spring and/
or door spring cable do not rub or contact the fill hose
or water supply line. Test by opening and closing the
door. Re-route the water supply lines if a rubbing noise
or interference occurs.
Solid Surface Countertop
Side Brackets
Plug buttons
Screw
Screw
Compression
Nut
Hot Water
Supply Line
90° Elbow
Ferrule
Bottom Left Side
STEP 12
POSITION DISHWASHER,
SECURE TO COUNTERTOP
OR CABINET (CONT.)
• Re-check that the dishwasher is squarely positioned
in the cabinet at both the top and bottom of the
appliance after mounting to the cabinets/countertop.
Adjust if necessary.
• Confirm all leveling legs are in contact with the floor
to prevent the dishwasher from rocking and ensure
proper door and latch operation
STEP 12
STEP 13
Brackets
Wood Countertop
Brackets
Wood Countertop
Plug buttons
Screw Screw
CONNECT DRAIN LINE
(CONT.)
• Connect drain line to air gap, waste tee or disposer
using the previously determined method. Secure
hose with a hose clamp.
Method 1 – Air gap with waste tee or disposer
Method 2 – “High drain loop” with waste tee or
disposer
With this method you will need the drain hose hanger
set aside in Step 1.
Fasten drain hose to underside of countertop with the
provided hanger.
IMPORTANT – When connecting drain line to
disposer, check to be sure that drain plug has been
removed. DISHWASHER WILL NOT DRAIN IF PLUG
IS LEFT IN PLACE.
Tip: Avoid unnecessary service call charges for a
no drain complaint.
Make sure excess drain hose has been pulled through
the cabinet opening. This will prevent excess hose
in the dishwasher cavity from becoming kinked or
crushed by the dishwasher.
Dishwasher Installation
Remove
Drain
Plug
12
CONNECT DRAIN LINE
• Detach the hose from the tub at locations indicated.
NOTE: Do not remove high drain loop.
The molded end of the drain hose will fit 5/8” through
1” diameter inlet ports on the air gap, waste tee or
disposer.
• Determine size of inlet port.
• Cut drain hose connector
on the marked line, if
required, to fit the inlet
port.
• If a longer drain hose is required, you can purchase
an extension drain hose - GE Appliances service
part WD24X10062 (4’ length) or WD24X10065
(12’ length) which can be connected directly to the
drain hose already attached to the unit. To use the
extension, you must cut the drain hose provided with
the unit as shown. Use a hose cutter or razor blade
knife to cut the drain hose.
• TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED
16’ FROM THE REAR OF THE DISHWASHER FOR
PROPER DRAIN OPERATION.
STEP 14 STEP 14
Remove
hose,
from
these
areas
only,
as
needed
Do NOT
remove
hose from
here (high
drain loop
area).
1”
5/8”
Cutting Line
IMPORTANT: Do not cut
corrugated portion of hose
Hose
Clamp
Cut Line
Dishwasher
Connection
House
Drain Hose on
Dishwasher
To use the 12’ drain hose extension:
Only cut ONE of these two locations
To use the 4’ drain
hose extension:
Only cut at this
location
72”
max.
Waste Tee Installation
72”
max.
Disposer Installation
Drain Hose Hanger
18”
min.
32” min. -
72” max.
Waste Tee Installation
Drain Hose Hanger
18”
min.
32” min. -
72” max.
Disposer Installation
Dishwasher Installation
13
CONNECT POWER SUPPLY
If a power cord with plug is already installed
proceed to Step 18.
In this step you will need the junction box cover and the
#10 Hex head screw from the screws set aside in Step 1.
• Secure house wiring to the back of the junction box
with a strain relief as shown in the MATERIALS YOU
WILL NEED section.
• Locate the 3 dishwasher wires, (white, black and green)
with the stripped ends coming out of the AC jumper. Use
UL-listed wire nuts of appropriate size to connect incoming
ground to green, white to white and black to black.
• Install the junction box cover using #10 hex head screw.
Check to be sure that wires are not pinched under the
cover and that all wire nuts are inside the cover.
• Make sure that the junction box cover is resting on
the mounting bracket.
To reduce the risk of electric shock, fire, or injury to
persons, the installer should check to ensure that wires
are not pinched or damaged, the house wiring is attached
to the junction box bracket through a strain relief, and
all electrical connections made at the time of install (wire
nuts) are contained inside of the junction box cover.
WARNING
STEP 15
PRETEST CHECKLIST
Review this list after installing your dishwasher to
avoid charges for a service call that is not covered
by your Warranty.
• Check to be sure power is OFF.
• Open door and remove all foam and paper
packaging.
• Locate the Owner’s Manual set aside in Step 1.
• Read the Owner’s Manual for operating instructions.
• Check door opening and closing. If door does not
open and close freely, check for proper routing of
spring cable over pulley. If door drops or closes
when released, adjust spring tension. See Step 2.
• Check to be sure that wiring is secure under the
dishwasher, not pinched or in contact with door
springs or other components. See Step 17.
• Check door alignment with tub. If door hits tub, level
dishwasher. See Step 13.
• Check door alignment with cabinet. If door hits
cabinet, reposition dishwasher. See Step 12.
• Pull lower rack out, about halfway. Check to be sure
it does not roll back or forward on the door. If the
rack moves, adjust leveling legs. See Step 13.
• Check that door spring does not contact water line,
fill hose, wiring or other components. See Step 12.
• Verify water supply and drain lines are not kinked
or in contact with other components. Contact with
motor or dishwasher frame could cause noise.
• Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be
between 120°F and 140°F. A minimum of 120°F
temperature is required for best wash performance.
See PREPARE HOT WATER LINE section.
• Add 2 quarts of water to the bottom of the
dishwasher to lubricate the pump seal.
• Turn on water supply. Check for leaks. Tighten
connections if needed.
• Remove protective film if present from the control
panel and door.
• Check that tub trim does not contact the door.
STEP 16
Para reducir el riesgo de descarga eléctrica, incendio
o lesiones a personas, el instalador deberá realizar un
control para asegurar que los cables no estén pellizcados
ni dañados, que el cableado del hogar esté conectado a la
ficha de la caja de empalmes a través de un amortiguador
de refuerzo, y que todas las conexiones eléctricas realizadas
en el momento de la instalación (tuercas para cables) estén
dentro de la tapa de la caja de empalmes.
ADVERTENCIA
NOTE: All ground screws, brackets and wires must remain intact.
Junction
Box Cover
Ground
(Green)
AC Power
Connector
White
Ground
Screw
Strain
Relief
BlackJunction
Box
Bracket
Dishwasher Installation
14
DISHWASHER WET TEST
• Turn on power supply or plug power cord into outlet,
if equipped.
• Select a cycle to run and push the Start/Reset pad.
• Ensure the door is latched. Dishwasher should start.
• Check to be sure that water enters the dishwasher.
If water does not enter the dishwasher, check to be
sure that water and power are turned on.
• Check for leaks under the dishwasher. If a leak
is found, turn off power at the breaker, and then
tighten water connections. Restore power after leak
is corrected.
NOTE: A small amount of water may splash out of
the fill funnel, on the right side of the tub, during the
first use after installation. Splash-out is most likely to
occur if there is air in the water supply line from new
construction or if the valve has been closed for an
extended time.
• Check for leaks around the door. A leak around
the door could be caused by door rubbing or
hitting against adjacent cabinets. Reposition the
dishwasher if necessary. See Step 12.
• Press and hold the Start/Reset pad for 3 seconds to
cancel the cycle. The unit will begin to drain. Check
drain lines. If leaks are found, turn off power at the
breaker and correct plumbing as necessary. Restore
power after corrections are made. See Steps 6, 7, 8,
9 and 16.
• Open dishwasher door and make sure all of the
water has drained. If not, check that disposer plug
has been removed and/or air gap is not plugged.
Also check drain hose to be sure it is not kinked
underneath or behind dishwasher. See Step 16.
• Press Start/Reset pad once again and run
dishwasher through another cycle. Check for leaks and
correct if required.
• Repeat these steps as necessary.
POSITION SOUND
BARRIER AND INSULATION
(on some models)
Skip this step if the sound barrier is assembled
to the dishwasher.
• Locate the sound insulation package inside the
dishwasher.
• Locate the control box.
• Apply the insulation to the underside of the control
box and flush with its front face as shown.
Insulation shown correctly placed along the bottom
edge of the control box, the dishwasher bottom and
flush with the front face.
If the insulation has an extension piece (on
some models) follow these additional steps:
• Open door all the way, if the door doesn’t stay fully
open, adjust the insulation panel.
• Align the screw holes with the screw holes on the
legs of the dishwasher.
• Ensure vent opening is not blocked by insulation.
STEP 17 STEP 18
Control
Box
Junction Box
Cover
(on some models)
Junction Box
Cover
Vent opening should be properly
aligned with cutout in the insulation
Dishwasher Installation
15
LITERATURE
•
Be sure to leave complete literature package, these Installation
Instructions and product samples and/or coupons with the
consumer.
INSTALL TOEKICK
• Remove the 2 screws installed on the front brace.
• Place toekick against the legs of the dishwasher.
• Align the toekick with the bottom edge and make
sure it is against the floor.
• Insert and tighten the 2 toekick attachment screws.
The toekick should stay in contact with the floor.
NOTE: Be careful not to over-tighten the screws in
the toekick.
• When reinstalling the toekick, on models with a sound
barrier, ensure that the bottom edge is flush with
the floor. Any excess material should be tucked up
behind the outer door.
Tip: Reduce sound from under the dishwasher.
Make sure toekick is against floor.
Attachment
Screws
Toekick
CHECK THE FOLLOWING
• Tub trim does not interfere with the door
• Dishwasher is square and level at both the top and
bottom of the cabinet opening, with no twisting or
distortion of the tub or door
• All 4 legs of the dishwasher are firmly in contact with
the floor
• Drain hose is not pinched between the dishwasher
and adjacent cabinets or walls
• Tub trim is fully seated on the tub flange
STEP 19
STEP 20
STEP 21
Remove these two screws
16
NOTE: Product improvement is a continuing endeavor. Therefore, materials,
appearance and specifications are subject to change without notice.
Printed in the United States
POUR VOTRE SÉCURITÉ
Veuillez lire et observer toutes les mises en garde
(AVERTISSEMENT et ATTENTION) données dans les
présentes directives.
Pour effectuer l’installation décrite dans les présentes
directives, il faut porter des gants et des lunettes de
sécurité.
IMPORTANT – Observez tous les codes et ordonnances
en vigueur.
• Note à l’installateur – Veuillez laisser les présentes
directives au consommateur pour l’inspecteur local.
• Note au consommateur – Veuillez conserver les
présentes directives avec votre Manuel d’utilisation
pour consultation ultérieure.
• Compétences requises – L’installation de ce
lave-vaisselle exige des compétences de base
en mécanique, en électricité et en plomberie.
L’installateur est responsable de la qualité
de l’installation. Toute défaillance du produit
attribuable à une installation inadéquate n’est
pas couverte par la garantie de GE Appliances.
Reportez-vous à la garantie du produit.
• Durée de l’installation – Entre 1 et 3 heures.
L’installation d’un nouveau lave-vaisselle exige plus de
temps que le remplacement d’un ancien modèle.
IMPORTANT – Le lave-vaisselle DOIT être installé de
manière à ce qu’il puisse être sorti de son emplacement
si des réparations sont nécessaires.
Il importe d'user de prudence lorsque l'appareil est
installé ou déplacé afin de prévenir l'endommagement
du cordon d'alimentation.
Si le lave-vaisselle que vous avez reçu est endommagé,
communiquez immédiatement avec votre détaillant ou
l’entrepreneur en construction.
Accessoires facultatifs – Reportez-vous au Manuel
d’utilisation pour connaître les ensembles pour panneau
décoratif personnalisé offerts.
Votre lave-vaisselle est un appareil qui chauffe l’eau.
VEUILLEZ LIRE ATTENTIVEMENT
CONSERVER CES DIRECTIVES
AVANT DE COMMENCER
Veuillez lire attentivement toutes les directives qui suivent.
• Avant de commencer l’installation, coupez toute
alimentation menant de l’appareil au disjoncteur ou
au fusible. Dans le cas contraire, vous pourriez être
victime d’une décharge électrique.
• Pour réduire les risques de choc électrique,
d’incendie ou de blessures, l’installateur doit
s’assurer que le lave-vaisselle est complètement
encastré au moment de l’installation.
• Un branchement inadéquat du conducteur de
mise à la terre peut présenter des risques de choc
électrique. Si vous n’êtes pas certain que l’appareil
est correctement mis à la terre, consultez un
réparateur ou un électricien qualifié. Si le câblage
électrique de la résidence n’est pas constitué de
deux fils plus un fil de mise à la terre, l’installateur
doit installer un fil de mise à la terre. Si le câblage
électrique de la résidence est en aluminium, utilisez
un agent antioxydant et des connecteurs pour
raccords «aluminium-cuivre» homologués UL.
•
Pour réduire les risques de choc électrique, d’incendie ou
de blessures, l’installateur doit vérifier pour s’assurer que
les fils ne sont pas pliés ou en dommagés, que le câblage
domestique est fixé au support de boîte de connexion par
l’entremise d’un serre-câble et que toutes les connexions
électriques faites au moment de l’installation (capuchons
de connexion) se trouvent à l’intérieur du couvercle de la
boîte de connexion
.
AVERTISSEMENT
Instructions
D’Installation
Lave-vaisselle encastré
Consultez votre Manuel du Propriétaire pour plus de détails sur la façon de nous contacter concernant les
questions d’installation
31-4000220 Rev 1 08-20 GEA
Ouvrir la porte causera le
basculement du lave-vaisselle
vers l’avant si son installation n’est pas complètement
terminée. Pour ouvrir la porte avant la finalisation
de l’installation, agrippez le haut du lave-vaisselle
fermement avec une main et tenir la porte de l’autre
main. Le port de gants est nécessaire.
ATTENTION
Préparation pour l’installation
2
PIÈCES FOURNIES
DANS L’EMBALLAGE :
• Couvercle de la boîte de jonction
• Vis à tête hexagonale n° 10
• Collier
• Support de tuyau de vidange
• 2 Boutons de bouchon
• Plinthe (préinstallée sur certains modèles)
• 2 Moulure de cuve (certains modèles)
• 2 Supports de montage pour comptoirs ou
armoires latérales en bois
• 2 Vis à tête spéciale Phillips n° 8-18 x 15,8 mm
(5/8 po) pour fixer le lave-vaisselle au dessous
du comptoir ou armoires latérales
• Pièces isolantes (certains modèles)
• Documentation, échantillons et(ou) bons
OUTILS NÉCESSAIRES :
• Tournevis cruciforme
• Tournevis à douille de 5/16 po et 1/4 po
• Clé à molette de 15 cm (6 po)
• Niveau
• Équerre de menuisier
• Ruban à mesurer
• Lunettes de sécurité
• Lampe de poche
• Seau pour attraper l’eau lors de la purge du tuyau
• Douille de 15/16 po
• Gants
• Pince
Pour une nouvelle installation :
• Coupe-tube
• Perceuse et mèches appropriées
• Jeu de scie-cloche
MATÉRIAUX NÉCESSAIRES :
• &RXGHÛGHôSR*+7*DUGHQ+RVH7KUHDG)LOHWDJH
à boyau d’arrosage) (joint d’étanchéité inclus) – Avec bout
opposé dimensionné pour la conduite d’eau chaude
• Ruban pour joints filetés
• Connecteurs vissables homologués UL (3)
• Ruban-cache
Pour une nouvelle installation :
• Coupure anti-refoulement pour le boyau de vidange, si nécessaire
• Raccord en T pour la plomberie de la résidence, s’il y a lieu
• Trousses de câbles électriques ou de cordons
électriques WXO9X70910 (1,65 m (5 pi 5 po de long)) ou
WX09X70911 (2,41 m (7 pi 11 po de long)) uniquement
• Bague anti-traction pour le raccordement électrique
• Colliers
• Robinet d’arrêt (recommandé)
• Conduite d’eau chaude – 9,5 mm (3/8 po) minimum, tuyau
en cuivre (incluant la bague et l’écrou à compression) ou
la pièce WX28X326 de GE, boyau métallique flexible.
• Boyau de vidange de 3,7 m (12 pi) de long WD24X10065
ou boyau de vidange de 1,2 m (4 pi) de long
WD24X10062 si nécessaire
Scie-cloche
Ruban à mesurer
Coupe-tube
Perceuse et
mèches
Tournevis
cruciforme
Douille de 15/16
Tournevis à douille
de 5/16 po et 1/4 po
Seau
Lampe de poche
Gants
Équerre de
menuisier
Lunettes de sécurité
Niveau
Couvercle
de la boîte
de jonction
Vis à tête
hexagonale n° 10
de 9,5 mm (3/8
po) de long pour
boîte de jonction
Documentation
Pince
Optionnel -
Boyau de vidange de 3,7 m (12 pi) - WD24X10065
Boyau de vidange de 1,2 m (4 pi) - WD24X10062
Coude de 90°
Robinet
d’arrêt
Boutons de
bouchon
Ruban-cache
Plinthe
Isolement
(certains modèles)
Supports de
montage
Support de tuyau de
vidange
Clé à molette
de 15 cm (6 po)
Connecteurs
vissables (3)
Vis à tête
spéciale Phillips
n° 8 de 15,8 mm
(5/8 po) de long
Raccord
en T
Coupure anti-
refoulement
Bague anti-
traction
Câble électrique
(ou cordon
d’alimentation,
s’il y a lieu)
Ruban pour
joints filetés
(s’il y a lieu)
Moulure de cuve
(sur certains modèles)
Collier
Colliers
Conduite
d’eau
chaude
PRÉPARATION DE L’OUVERTURE
DANS LES ARMOIRES
• L’ouverture dans les armoires doit mesurer au moins 61,0 cm (24
po) de largeur et de profondeur, et environ 87,6 cm (34-1/2 po)
de hauteur à partir du plancher jusqu’au-dessous du comptoir.
• Le lave-vaisselle doit être installé de façon à ce que le boyau
de vidange mesure au maximum 4,88 mètres (16 pieds) pour
assurer une vidange adéquate.
• Le dessus, les côtés et l’arrière du lave-vaisselle doivent être
complètement dissimulés à l’intérieur de l’ouverture. Le lave-vaisselle
ne doit soutenir aucune partie de la structure des armoires.
DÉGAGEMENTS:
• Dans le cas
d’une installation
dans un coin,
veuillez prévoir
un dégagement
d’au moins 5,1
cm (2 po) entre
le lave-vaisselle
et les armoires,
le mur ou un
électroménager
adjacent. Veuillez
prévoir un
dégagement d’au
moins 65 cm (25-1/2 po) à l’avant du lave-vaisselle pour
l’ouverture de la porte.
Préparation pour l’installation
3
33-1/2 po to 34-3/4
po du dessous
du comptoir au
plancher
Le mur du fond
doit être exempt
de tuyaux ou
de fils
La partie ombrée est
réservée à la plomberie et
à l’électricité
Armoires à
l’équerre et
d’aplomb
61,0 cm
(24 po) min.
15,2 cm (6 po)
61,0 cm
(24 po) min.
10,1 cm
(4 po)
Clearance for Door
Opening 2" Minimum
Countertop
Dishwasher
25-1/2"
Comptoir
Lave-vaisselle
5,1 cm (2 po) minimum
pour l’ouverture de la porte
65 cm (25-1/2 po)
EXIGENCES RELATIVES AU
SYSTÈME DE VIDANGE
• Veuillez observer les ordonnances et les codes locaux en vigueur.
• Le boyau de vidange doit avoir une longueur maximale de 4,88
mètres (16 pieds).
REMARQUE : Il faut installer une coupure anti-refoulement si le
raccord au broyeur à déchets ou au raccord en T se trouve à moins
de 46 cm (18 po) au-dessus du plancher afin d’éviter un siphonage.
CHOIX DE LA MÉTHODE DE VIDANGE
Le type d’installation de vidange dépend des conditions suivantes.
• Les ordonnances ou codes locaux en vigueur exigent-ils une
coupure anti-refoulement?
• Le raccord T se trouve-t-il à moins de 46cm (18po) du plancher?
Si vous répondez OUI à l’une ou l’autre de ces
questions, vous DEVEZ utiliser la méthode n° 1.
• Si vous répondez NON, vous pouvez employer l’une ou l’autre
des méthodes.
PRÉPARATION DES ARMOIRES
• Percez un trou de 3,8 cm (1-1/2 po) de diamètre dans la paroi de
l’armoire qui se trouve dans la partie ombrée de la PRÉPARATION
DE L’OUVERTURE DANS LES ARMOIRES pour le boyau de
vidange. Assurez-vous que l’orifice ne présente pas d’arêtes vives.
IMPORTANT – Lorsque vous branchez le boyau de vidange
à un broyeur à déchets, assurez-vous
d’enlever le bouchon de vidange. LE
LAVE-VAISSELLE NE POURRA PAS
SE VIDER SI VOUS LAISSEZ LE
%28&+21(13/$&(
Méthode n° 1 – Coupure anti-refoulement avec raccord en
T ou broyeur à déchets
Il faut installer une coupure anti-refoulement lorsqu’elle est exi-
gée par les ordonnances et les codes locaux en vigueur. Cette
coupure anti-refoulement doit être installée conformément aux
directives données par le fabricant.
Méthode n° 2 – Boucle de vidange élevée avec raccord en
T ou broyeur à déchets
Conseil: Pour éviter des frais de réparation inutiles.
Assurez-vous d’enlever le bouchon de vidange du broyeur à
déchets avant d’y brancher le boyau de vidange du lave-vaisselle.
Pour réduire les risques de
choc électrique, d’incendie
ou de blessures, l’installateur doit s’assurer que le
lave-vaisselle est complètement encastré au moment
de l’installation.
AVERTISSEMENT
Remove
Drain
Plug
Enlevez le
bouchon
de vidange
DIMENSION DE LA POIGNÉE DU LAVE-VAISSELLE : La
porte de ce lave-vaisselle doit être à niveau avec l’armoire.
Pour les modèles avec poignée, la profondeur totale (avec
poignée) est de 67,9 cm (26 ¼ po) maximum selon le modèle.
Consultez le document de spécifications rapides en ligne pour
obtenir plus de dimension de lave-vaisselles.
182,8 cm
(72 po)
max.
182,8 cm
(72 po)
max.
Crochet pour boyau de vidange
82 cm
(32 po)
min. -
182,8 cm
(72 po)
max.
46 cm
(18 po) min.
Crochet pour
boyau de vidange
46 cm
(18 po) Min.
82 cm
(32 po)
min. -
182,8 cm
(72 po)
max.
4
Préparation pour l’installation
Préparation des armoires et cheminement des fils
• Les fils peuvent entrer dans l’ouverture du côté droit,
du côté gauche, de l’arrière ou du plancher dans la
partie ombrée de la figure et de la PRÉPARATION DE
L’OUVERTURE DANS LES ARMOIRES.
• Percez un trou de 3,8 cm (1-1/2 po) de diamètre au
maximum pour le passage du câble électrique. Le bord du
trou doit être lisse et arrondi. Les fils électriques pour le
branchement permanent peuvent passer par le même trou
que le boyau de vidange et la conduite d’eau chaude, si
c’est plus pratique. Si le trou est pratiqué dans une paroi
en métal, les bords de l’orifice doivent être recouverts d’un
passe-fils pour protéger les fils.
REMARQUE: Le cordon d’alimentation doté d’une fiche doit
passer par un autre trou dans l’armoire.
Branchement électrique du lave-vaisselle
Le branchement électrique s’effectue du côté avant droit du
lave-vaisselle.
• Dans le cas d’un branchement permanent, le câble doit
être acheminé de la façon indiquée à la figure. Le câble
doit avoir une longueur minimale de 61 cm (24 po) à partir
du mur arrière.
• Dans le cas d’un branchement avec un cordon
d’alimentation, installez une prise de courant mise à la
terre à trois broches sur la paroi de l’armoire adjacente,
entre 15 cm (6 po) et 46 cm (18 po) de l’ouverture, et entre
15 cm (6 po) et 46 cm (18 po) du plancher.
• Utilisez uniquement WX09X70910 (1,65 m (5 pi 5 po de
long)) ou WX09X70911 (2,41 m (7 pi 11 po de long))
Trousse de cordon d’alimentation pour lave-vaisselle.
N’utilisez pas une rallonge électrique ou un adaptateur de
fiche avec cet appareil.
PRÉPARATION DU CÂBLAGE ÉLECTRIQUE
Avant de commencer l’installation, coupez toute
alimentation menant de l’appareil au disjoncteur ou
au fusible. Dans le cas contraire, vous pourriez être
victime d’une décharge électrique.
AVERTISSEMENT
Un branchement inadéquat du conducteur de
mise à la terre peut présenter des risques de choc
électrique. Si vous n’êtes pas certain que l’appareil est
correctement mis à la terre, consultez un réparateur
ou un électricien qualifié. Si le câblage électrique de la
résidence n’est pas constitué de deux fils plus un fil de
mise à la terre, l’installateur doit installer un fil de mise
à la terre. Si le câblage électrique de la résidence
est en aluminium, utilisez un agent antioxydant et
des connecteurs pour raccords «aluminium-cuivre»
homologués UL.
AVERTISSEMENT
ALIMENTATION ÉLECTRIQUE
Assurez-vous que le branchement électrique et le
calibre du fil sont adéquats et conformes avec la version
UpFHQWHGHODQRUPH$16,1)3$OH&RGHQDWLRQDOGH
l’électricité, tous les règlements et toutes les ordonnances
de votre région.
L’alimentation électrique de cet appareil doit être :
9+]HQFRXUDQWDOWHUQDWLIVHXOHPHQWDYHFXQ
fusible de 15 ou 20 A.
• Le câble électrique doit posséder deux fils, plus un fil de
mise à la terre, et résister à une température nominale de
&)
• Si votre alimentation électrique ne répond pas à ces
exigences, appelez un électricien agréé avant de
poursuivre l’installation.
Nous recommandons d’avoir :
• Un disjoncteur ou fusible temporisé.
• Un circuit de dérivation individuel mis à la terre approprié.
Mise à la terre – Branchement permanent
Cet appareil doit être branché à un réseau électrique
permanent mis à la terre. Sinon, il faut installer un
conducteur de mise à la terre avec les conducteurs du
circuit et le brancher à la borne de mise à la terre du
réseau ou au fil de mise à la terre de l’appareil.
Mise à la terre – Modèles dotés d’un cordon
d’alimentation
Cet appareil doit être mis à la terre. En cas de mauvais
fonctionnement ou de défaillance, la mise à la terre réduira
les risques de choc électrique en fournissant au courant
électrique un circuit de moindre résistance. Cet appareil est
doté d’un cordon d’alimentation possédant un conducteur
de mise à la terre et une fiche de mise à la terre. La fiche
doit être branchée dans une mise appropriée, installée et
mise à la terre en conformité avec tous les codes locaux et
ordonnances en vigueur.
Zone pour
la prise de
courant
Autre emplacement
possible pour la prise
de courant dans une
armoire adjacente
46 cm (18 po)
46 cm
(18 po)
15 cm (6 po)
15 cm
(6 po)
Trou de 3,8 cm
(1-1/2 po) de dia.
(max.)
7,6 cm (3 po)
des armoires
61 cm (24
po) du mur
Mise à la terre
Noir
Blanc
Dans le cas des modèles dotés d’un cordon
d’alimentation : Ne modifiez pas la fiche fournie avec
l’appareil; si vous ne pouvez pas la brancher dans la
prise de courant, faites installer une prise de courant
appropriée par un technicien qualifié.
AVERTISSEMENT
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
GE GDF535PGRWW Mode d'emploi
- Catégorie
- Lave-vaisselle
- Taper
- Mode d'emploi
