Hilti GX 3 Manuel utilisateur

GX 3

GX 3-ME















1

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

GX 3

en Originaloperatinginstructions....................................... 1

fr Moded'emploioriginal........................................... 14

tr Orijinalkullanımkılavuzu ......................................... 27

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 40

ko 오리지널사용설명서 ............................................. 53

zh 原始操作說明.................................................. 65

cn 原版操作说明.................................................. 76

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 1

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that may occur when handling or using the product. The following signal

words are used in combination with a symbol:

DANGER! Draws attention to an imminent hazard that will lead to serious personal injury or

fatality.

WARNING! Draws attention to a potential hazard that could lead to serious personal injury or

fatality.

CAUTION! Draws attention to a potentially dangerous situation that could lead to minor personal

injury or material damage.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use

Instructions for use and other useful information

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions.

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text.

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

This symbol is intended to draw special attention to certain points when handling the product.

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols are used on the product:

General symbol for "must do"

Wear eye protection

Wear ear protection

Wear a hard hat

Return waste material for recycling

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

2 English

1.4 Text markings

1.4.1 Highlighting text passages

Designations and markings are indicated as follows:

‚ ‛ Description of marked operating controls on the fastening tool.

« » Markings on the fastening tool

1.5 Product information

Hilti products are designed for professional use and may be operated, serviced and maintained only by

trained, authorized personnel. This personnel must be informed of any particular hazards that may be

encountered. The product and its ancillary equipment can present hazards if used incorrectly by untrained

personnel or if used not in accordance with the intended use.

The type designation and serial number are stated on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Fastening tool, gas-actuated GX 3

Generation 01

Serial no.

1.6 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration of conformity can be found at the end of this documentation.

The technical documentation is filed and stored here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 Safety precautions

Working safely with the setting tool

▶Pressing the nosepiece of the setting tool against a part of the body may lead to serious injury due to

inadvertent actuation and release of a fastener. Never press the nosepiece of the tool against your

hand or any other part of the body.

▶When inserting/loading application-specific fasteners (e.g. washers, clips or clamps, etc.) in/on the

fastener guide there is a risk of serious injury due to inadvertent actuation of the tool resulting in

discharge of a fastener. When inserting/loading an application-specific type of fastener, never press

a hand or any other part of the body against the fastener guide.

▶Never point the setting tool towards yourself or any other person.

▶Keep your arms flexed when operating the tool (do not straighten the arms).

▶Stay alert, watch what you are doing and use common sense when operating the setting tool. Do

not use the setting tool while you are tired or under the influence of drugs, alcohol or medication.

A moment of inattention while operating the setting tool may result in serious personal injury.

▶When pulling back the nail pusher, always take care to ensure that it engages.

▶When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward

slowly. There is a risk of pinching the fingers.

▶Do not attempt to drive fasteners into materials that are too hard, such as welded steel or cast steel.

Attempting to drive fasteners into these materials may lead to malfunctions, incorrectly driven fasteners

or breakage of fasteners.

▶Do not attempt to drive fasteners into materials that are too soft, such as wood or drywall/gypsum

board. Attempting to drive fasteners into these materials may lead to malfunctions and fasteners being

driven incorrectly or driven right through the material.

▶Do not attempt to drive fasteners into materials that are too brittle, such as glass or tiles. Attempting

to drive fasteners into these materials may lead to malfunctions, fasteners being driven incorrectly and

may cause the material to shatter.

▶Before driving fasteners, check that there is no risk of injuring persons or of damaging objects present

behind or below the working surface.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 3

▶Only activate the trigger when the setting tool is pressed against the base material in such a way that the

fastener guide is plunged into the setting tool as far as it will go.

▶Always wear gloves if you have to carry out maintenance work on the setting tool while it is still

hot.

▶If fasteners are driven at a high rate or if the tool used for a long period, surfaces of the tool beyond the

grip areas may get hot. Wear protective gloves to avoid burning injuries.

▶If the setting tool overheats, remove the gas can and allow the tool to cool down. Do not exceed the

specified maximum fastener driving rate.

▶Driving fasteners may cause flying fragments or result in parts of the nail strip material being forcibly

ejected from the tool. Flying fragments present a risk of injury to the body and eyes. Wear a suitable

form of eye protection, ear protectors and a hard hat. Depending on the application and type of tool

in use, wearing personal protective equipment such as a dust mask, non-slip safety footwear, hard hat

or suitable eye protection and ear protection reduces the risk of injury. Other persons in the vicinity must

also wear eye protection and a hard hat.

▶Wear suitable ear protection (see noise information in the technical data section). The fastener is driven

by the energy released on ignition of a gas-air mixture. The resulting noise exposure may cause damage

to the hearing. Other persons in the vicinity should also wear suitable ear protection.

▶When driving a fastener, always hold the setting tool securely and at right angles to the supporting

material. This helps to avoid deflection of the fastener by the supporting material.

▶Never drive a second fastener at the same location. This may lead to breakage or jamming of fasteners.

▶Never attempt to redrive a previously driven stud or nail. Re-use of a fastener may cause it to break,

thereby presenting a risk of injury.

▶Alway remove the gas can and ( → page 8) empty the magazine ( → page 8) before changing the magazine,

before cleaning, servicing or maintenance work on the tool, before storage or transport and before leaving

the setting tool unattended.

▶After use, lay the tool flat on the floor. A tool that is mounted on a pole tool extension and left leaning

against a wall presents a risk of injury as it may fall over.

▶When lowering (tilting) the pole tool extension, do not hold the pole only at its lower end. The considerable

leverage exerted may cause you to lose control over the tilting movement of the pole and tool. This may

result in injury and damage to the equipment or other property.

▶To ensure that the setting tool functions faultlessly and as intended, always check the tool and accessories

for possible damage before use. Check that moving parts function faultlessly, without sticking, and that

no parts are damaged. In order to ensure faultless operation of the tool, all parts must be fitted correctly

and must meet the necessary requirements. Damaged protective devices or other parts must be properly

repaired or replaced by Hilti Service unless otherwise stated in the operating instructions.

▶Have the setting tool repaired only by trained and qualified specialists using genuine Hilti spare parts.

This will ensure that the safety of the setting tool is maintained.

▶Tampering with or modification of the setting tool is not permissible.

▶Do not use the setting tool where there is a risk of fire or explosion.

▶Take influences of the surrounding area into account. Do not expose the setting tool to rain or snow and

do not use it in damp or wet conditions.

▶Use the setting tool only in well-ventilated working areas.

▶Select the correct combination of fastener guide and fastener. The wrong combination may result in

damage to the tool and in reduced fastening quality.

▶Always observe the application guidelines .

Hazards presented by electricity

▶Before beginning work, check the working area (e.g. using a metal detector) to ensure that no concealed

electric cables or gas and water pipes are present.

▶Hold the setting tool only by the insulated grip when working in areas where fasteners may be driven

inadvertently into concealed electric cables. Contact with a live electric cable may cause metal parts of

the tool also to become live, leading to a risk of electric shock.

Instructions for handling the propellant gas

▶Observe the instructions printed on the gas can and in the accompanying information.

▶Escaping gas is harmful to the lungs, skin and eyes. Keep your face and eyes away from the gas can

compartment for up to about 10 seconds after removing the gas can.

▶Do not operate the gas can valve manually.

▶If a person has inhaled gas, take the person into the open air or into a well-ventilated area and place the

person in a comfortable position. Consult a doctor if necessary.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

4 English

▶Call a doctor if the person is unconscious. Bring the person into a well-ventilated area and place the

person in the stable recovery position (i.e. lying on the side). If the person is not breathing, administer

artificial respiration and, if necessary, supply oxygen.

▶After eye contact with gas, rinse the open eyes thoroughly under running water for several minutes.

▶After skin contact with gas, wash the contact area carefully with soap and warm water. Subsequently

apply a skin cream.

General instructions concerning personal safety

▶Take care to adopt an ergonomic body position. Work from a safe stance and take care to stay in balance

at all times. This will allow you to control the setting tool better, even in unexpected situations.

▶Keep other people away from the working area, especially children.

3 Description

3.1 Overview of the product 1

@Fastener guide

;Slider for fastener driving depth adjustment

and for releasing the fastener guide

=RESET button

%Inlet/outlet valve

&Cooling air slots

(Belt hook

)Trigger

+Grip

§Nail pusher

/Magazine lockbutton

:Support leg

∙Magazine

$Type identification plate

£Gas can status indicator

|GAS button

¡Gas can compartment

QGas can compartment cover

3.2 Intended use

The product described is a gas-actuated fastening tool (“fastening tool”). It is designed to drive suitable

fasteners into concrete, steel, sand-lime block, concrete-block masonry, rendered masonry and other

materials suitable for use of the direct fastening technique.

The fastening tool is for hand-held use or use with the pole tool extension (accessory) only.

3.3 Items supplied

Gas-actuated fastening tool with fastener guide, toolbox, operating instructions.

Other system products approved for use with this product can be found at your local Hilti Center or online

at: www.hilti.group

3.4 Fastener guide

The fastener guide holds the studs or, respectively, guides the nails and, when the tool is fired, thus directs the

fasteners into the supporting material at the desired position. Application-specific fastener guides (IF or ME)

are available for the GX 3 and GX 3-ME fastening tools (see type identification plate for exact designation).

3.5 Fasteners

Two types of fastener can be driven by the fastening tool: nails and threaded studs. Additional fastening

components, which can be inserted in the fastener guide, are also available for various applications.

3.6 Slider for fastener driving depth adjustment and for releasing the fastener guide

The slider can be used to reduce the depth to which the fastener is driven. In the EJECT position, it releases

the fastener guide for removal.

Status Meaning

+• Standard fastener driving depth

• Reduced fastener driving depth

EJECT • Fastener guide release

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 5

3.7 RESET button

After driving a fastener, under certain circumstances, the fastener guide may not return to its outset position.

This is caused by the piston being incorrectly positioned. The incorrect piston position can be remedied by

pressing the RESET button.

Status Meaning

RESET button projects from the tool casing. Its

white edge is visible. • Piston position is incorrect

RESET button is flush with the tool casing. • Piston position is correct

3.8 Support leg

On an even working surface, the support leg makes it easier to hold the fastening tool perpendicular as

attention then only has to be paid to lateral alignment. On an uneven or undulating surface it may be necessary

to remove the support leg in order to allow the fastener guide to be held perpendicular to the working surface.

3.9 Belt hook

The belt hook can be extended in two stages.

Status Meaning

First position • Position for attaching to a waist belt

Second position • Position for attaching to ladders, scaffolds,

platforms, etc.

3.10 Gas can

Note

Observe the safety instructions provided with the gas can!

In order to operate the fastening tool, the gas can must be inserted in the gas can compartment.

The gas can status can be read from the LED display after pressing the GAS button.

The gas can must be removed before breaks between working, before maintenance and before transporting

or storing the fastening tool.

3.11 Indication of gas can status

After pressing the GAS button, the LED display indicates the status of the gas can.

Note

The gas level indicator does not operate correctly if the fastener guide / tool nosepeice has been fully

compressed.

Status Meaning

All four LEDs light green. • Level is approx. 100 %.

Three LEDs light green. • Level is approx. 75 %.

Two LEDs light green. • Level is approx. 50 %.

One LED lights green. • Level is approx. 25 %.

One LED blinks green. • Level is below 10 %. Replacement of the gas

can is recommended.

One LED lights red. • There is either no gas can in the fastening tool,

the wrong type of gas can is fitted or the can is

empty.

Note

Even when the level is indicated as “empty”, the gas can, for technical reasons, still contains a little gas.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

6 English

4 Technical data

4.1 Fastening tool

Weight (empty) 8.6 lb

(3.9 kg)

Application temperature, ambient temperature 14 ℉ …113 ℉

(−10 ℃ …45 ℃)

Maximum fastener length 1.5 in

(39 mm)

Fastener diameter • 0.10 in (2.6 mm)

• 0.12 in (3.0 mm)

Compression stroke 1.6 in

(40 mm)

Magazine capacity 40 + 2 nails

Maximum fastener driving frequency (Fasteners per hour) 1,200

Maximum magnetic field strength −16.5 dBµA/m

Frequency 13,553 MHz …13,567 MHz

4.2 Noise information and vibration values

The sound pressure and vibration values given in these instructions have been measured in accordance

with a standardized test and may be used to compare one fastening tool with another. They may be used

for a preliminary assessment of exposure. The data given represents the main applications of the fastening

tool. However, if the fastening tool is used for different applications, with different accessories or is poorly

maintained, the data may vary. This may significantly increase exposure over the total working period. An

estimation of the level of exposure should also take into account the periods of time when the tool is not

actually in use. This may significantly reduce exposure over the total working period. Prescribe additional

safety measures to protect the operator from the effects of noise and/or vibration, such as: maintenance of

the direct fastening tool and its additional equipment or accessories, keeping the hands warm, organization

of work patterns.

Noise emission values determined in accordance with EN 15895

Emission sound pressure level at the workplace (LpA, 1s)99 dB(A)

Peak sound pressure level at the workplace (LpC, peak)133 dB (C)

Sound (power) level (LWA)105 dB(A)

Sound level uncertainty 2 dB(A) / 2 dB(C)

Recoil

Energy-equivalent acceleration, (ahw, RMS(3))Applicable to 1 mm sheet metal

on B35 concrete: 3.64 m/s2

Measurement uncertainty 0.13 m/s²

5 Loading the fastening tool

5.1 Loading for driving nails

5.1.1 Equipment required for driving nails

Nails are fed through the magazine in strip form (ready-to-use strips of nails).

Note

When driving nails there must be no single-fastener adapter present in the tool .

5.1.2 Loading the magazine

1. Pull the nail pusher back until it engages.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 7

2. Slide the nail strips into the magazine as far as they will go.

Note

Strips of short nails could be inadvertently inserted the wrong way round. With short nails, take

care to ensure that the tips of the nails point towards the nose of the tool.

WARNING

Risk of finger injury! Fingers could be pinched when the nail pusher is released.

▶When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward

slowly as far as it will go.

3. Release the nail pusher and guide it forward as far as it will go.

5.1.3 Inserting the gas can

1. Open the gas can compartment cover.

2. Remove the cap from the gas can.

Note

Keep the cap so that it can be used to close the gas can securely when it is removed from the

tool, e.g. when unloading and for transport.

3. Slide the gas can into the gas can compartment, valve first, so that the gas can clip enters the opening

for the clip and engages securely.

4. Close the gas can compartment cover.

5. Without pulling the trigger, firmly press the setting tool with the fastener guide three times against the

base material in order to bleed the gas lines of air.

5.2 Loading for driving threaded studs

5.2.1 Equipment required for driving threaded studs

Threaded studs must be inserted singly in the fastener guide from the front. An adapter is required for driving

single fasteners. The packaging units for threaded studs each contain an adapter for individual setting, with

the corresponding fitting information.

Note

In order to drive threaded studs, the magazine must first be emptied and an adapter for driving single

fasteners inserted.

5.2.2 Inserting the single-fastener adapter

▶Insert the single-fastener adapter ( → page 9).

5.2.3 Inserting the gas can

▶Insert the gas can ( → page 7).

6 Driving fasteners

6.1 Driving nails

WARNING

Risk of injury! Pressing the nosepiece of the fastening tool against a part of the body may lead to

serious injury due to inadvertent firing and release of a fastener.

▶Never press the nosepiece of the tool against your hand or any other part of the body.

1. Check the fastener driving depth setting.

2. Bring the nosepiece of the setting tool and the support leg into contact with the working surface.

3. Using the fastener guide, press the setting tool as far as it will go against the base material.

4. Check that the fastener guide is perpendicular to the working surface.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

8 English

5. Pull the trigger to drive a fastener.

Note

It is not possible to drive a fastener if the fastener guide is not pressed fully against the working

surface.

6. Lift the fastening tool completely away from the working surface after driving a fastener.

7. Remove the gas can ( → page 8) and empty the magazine ( → page 8) when work with the setting tool is

finished or before leaving the tool unattended.

6.2 Driving threaded studs

WARNING

Risk of injury! Pressing the nosepiece of the setting tool against a part of the body may lead to

serious injury due to inadvertent firing and release of a fastener.

▶When inserting fasteners, on no occasion press the fastener guide against a hand or any

other part of the body.

▶Never press the nosepiece of the tool against your hand or any other part of the body.

WARNING

Risk of injury by falling objects! Triggering the tool again on top of a nail or stud that was not

optimally driven may weaken the fastening. The object that was fastened may fall down as a result,

causing damage or injury.

▶Never trigger the tool again in an attempt to improve the hold of a previously driven nail or

stud.

1. Check the fastener driving depth setting.

2. Insert a stud in the fastener guide.

3. Bring the nosepiece of the setting tool and the support leg into contact with the working surface.

4. Using the fastener guide, press the setting tool as far as it will go against the base material.

5. Check that the fastener guide is perpendicular to the working surface.

6. Pull the trigger to drive a fastener.

Note

It is not possible to drive a fastener if the fastener guide is not pressed fully against the working

surface.

7. Remove the gas can when work with the setting tool is finished or before leaving the tool unattended

( → page 8).

7 Unloading the fastening tool

7.1 Removing the gas can

1. Open the gas can compartment cover.

2. Press the gas can clip to release the gas can.

3. Remove the gas can from the gas can compartment.

4. Fit the cap on the gas can.

5. Close the gas can compartment cover.

7.2 Unloading the magazine

1. Pull the nail pusher back until it engages.

2. Remove all nail strips from the magazine.

WARNING

Risk of finger injury! Fingers could be pinched when the nail pusher is released.

▶When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward

slowly as far as it will go.

3. Release the nail pusher and guide it forward as far as it will go.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 9

7.3 Removing the single-fastener adapter

▶After driving the fasteners, remove the single-fastener adapter ( → page 10) from the fastening tool.

8 Optional operating steps

8.1 Checking the status of the gas can

1. Without pressing the fastening tool against the working surface, press the GAS button.

2. Read the gas can status from the display. → page 5

8.2 Removing the magazine

1. Pull the nail pusher back until it engages.

2. Remove the loose nail strips from the magazine.

WARNING

Risk of finger injury! Fingers could be pinched when the nail pusher is released.

▶When disengaging the nail pusher, do not release it and allow it to jump forward. Guide it forward

slowly as far as it will go.

3. Release the nail pusher and guide it forward as far as it will go.

4. Release the magazine locking catch.

5. Pivot the magazine about the pivot point towards the front.

6. Detach the magazine.

8.3 Fitting the magazine

1. Release the magazine locking catch.

2. Engage the front end of the magazine with the setting tool.

3. Pivot the magazine towards the setting tool as far as it will go.

4. Close the magazine locking catch.

8.4 Removing the fastener guide

1. Remove the gas can. → page 8

2. Move the fastener guide release slider to the EJECT position.

3. Remove the fastener guide.

8.5 Inserting the fastener guide

1. Remove the gas can. → page 8

2. Slide the fastener guide into the slot in the nose of the fastening tool.

3. Hold the fastener guide securely so that it cannot fall out and then press the nose of the tool (i.e. the tool

with the fastener guide) against a firm surface until the fastener guide engages.

4. Check that the fastener guide has engaged.

◁Once the fastener guide has engaged, the slider for releasing the fastener guide is again in the +

position.

8.6 Removing the support leg

1. Release the support leg engaging mechanism by pressing lightly.

2. Rotate the support leg through 90°.

3. Remove the support leg.

8.7 Fitting the support leg

1. Bring the support leg into contact with the magazine at right angles and guide it into the slot.

2. Rotate the support leg through 90° relative to the magazine and allow it to engage while applying light

pressure.

8.8 Inserting the single-fastener adapter

1. Remove the gas can. → page 8

2. Remove the magazine. → page 9

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

10 English

3. Insert the single-fastener adapter.

4. Fit the magazine. → page 9

8.9 Removing the single-fastener adapter

1. Remove the gas can. → page 8

2. Remove the magazine. → page 9

3. Remove the single-fastener adapter.

4. Fit the magazine. → page 9

9 Remedying possible malfunctions

9.1 Remedying an incorrect piston position

▶Check the position of the RESET → page 5 button.

Result

•RESET button projects from the tool casing. Its white edge is visible.

▶To remedy the incorrect piston position, press the RESET button.

9.2 Removing foreign objects and nails from the area around the fastener guide

CAUTION

Risk of injury by flying parts! Triggering the tool (attempting to drive a fastener) when foreign objects

are present in the area around the fastener guide, or when a fastener is jammed in the fastener guide,

may lead to injury caused by flying objects or fragments.

▶Never attempt to remedy tool malfunctions by continuing to trigger the tool!

1. Remove the gas can. → page 8

2. Unload the magazine. → page 8

3. Remove the magazine. → page 9

4. Remove the fastener guide. → page 9

5. Remove all foreign objects and nails from the area around the fastener guide.

6. Insert the fastener guide. → page 9

7. Fit the magazine. → page 9

10 Care and maintenance

10.1 Caring for the fastening tool

▶Never operate the fastening tool if the cooling air slots are blocked.

▶Keep the grip areas free from oil and grease.

▶Clean the fastening tool regularly. → page 10

▶Do not use spray devices, pressure jet washers or running water for cleaning.

▶Do not use cleaning agents containing silicone.

▶Do not use sprays or similar lubricating and cleaning agents.

10.2 Cleaning the fastening tool

1. Remove the gas can. → page 8

2. Unload the magazine. → page 8

3. Remove plastic fragments from the fastener guide.

4. Use a dry brush to clean the cooling air slots, taking care to prevent dirt or foreign objects entering the

interior of the tool.

5. Use a damp cloth to clean the exterior of the tool.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 11

11 Transport and storage

11.1 Maintenance

▶To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Center or online at: www.hilti.group.

▶Check all external parts of the fastening tool for signs of damage at regular intervals and make sure that

all the controls function correctly.

▶Do not use the fastening tool if parts are damaged or if the controls do not function correctly.

▶Have a defective fastening tool repaired by Hilti Service.

11.2 Checks after care and maintenance work

▶Move the fastener driving depth adjustment slider to the +position.

12 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

Malfunction Possible cause Action to be taken

Fasteners are frequently

driven to inadequate depth.

Driving power is too low. ▶Move the fastener driving depth

adjustment slider to the +

position.

The fasteners are too long. ▶Use shorter fasteners.

The supporting material is too

hard.

▶Consider using a DX fastening

tool.

The inlet/outlet valve is clogged or

covered over.

▶Clean the fastening tool and

check how it is held.

Fasteners are frequently

driven too deeply.

Driving power is too high. ▶Move the fastener driving depth

adjustment slider to the ‒

position.

The fasteners are too short. ▶Use longer fasteners.

Fasteners break.

Driving power is too low. ▶Move the fastener driving depth

adjustment slider to the +

position.

The fasteners are too long. ▶Use shorter fasteners.

The supporting material is too

hard.

▶Consider using a DX fastening

tool.

The fastener guide is not held per-

pendicular to the working surface.

▶Press the nosepiece against

the working surface, keeping

the tool perpendicular to the

surface.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

12 English

Malfunction Possible cause Action to be taken

Fasteners bend.

Driving power is too low. ▶Move the fastener driving depth

adjustment slider to the +

position.

The fasteners are too long. ▶Use shorter fasteners.

The fastener guide is not held per-

pendicular to the working surface.

▶Press the nosepiece against

the working surface, keeping

the tool perpendicular to the

surface.

Fasteners do not hold in steel

base material.

The supporting material is too thin. ▶Use a different fastening

method.

The content of the gas can is

inadequate for the number of

fasteners in the package.

High gas consumption due to fre-

quent compression of the tool

nosepiece without driving a fas-

tener.

▶Avoid compressing the tool

nosepiece without driving a

fastener.

The tool remains compressed

(nose does not extend when

pressure is released).

Incorrect piston position. ▶Remedy the incorrect piston

position. → page 10

The nail detector is jammed and

the RESET button is not flush with

the casing when pressed.

▶Remove foreign objects and

nails from the area around the

fastener guide. → page 10

A fastener has jammed in the fas-

tener magazine.

▶Release the jammed fastener.

A nail is jammed under the lever

ahead of the piston face.

▶Remove the gas can, press

the tool nosepeice against the

working surface and pull the

trigger firmly.

Fastener driving failure rate is

too high. The fastener magazine is not held

perpendicular to the working sur-

face.

▶Press the nosepiece against the

working surface, keeping the

fastener guide perpendicular to

the surface.

Wrong type of fastener used. ▶Use a suitable type of fastener.

The supporting material is too

hard.

▶Consider using a DX fastening

tool.

No fastener is driven. The nail pusher was not moved

forward.

▶Release the nail pusher and

guide it forward as far as it will

go.

Insufficient nails in the magazine (2

nails or fewer).

▶Load the magazine. → page 6

Nail transport malfunction. ▶Use a different nail strip.

▶Clean the magazine.

Gas can is empty. ▶Check the status of the gas can.

→ page 9

LED 1 lights red ▶Check the status of the gas can.

→ page 9

Air in the gas lines ▶Press the setting tool three

times in position without pulling

the trigger.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

English 13

Malfunction Possible cause Action to be taken

No fastener is driven. Foreign object in the area of the

fastener guide

▶Remove foreign objects and

nails from the area around the

fastener guide. → page 10

The fastening tool is too hot. ▶Allow the fastening tool to cool

down.

Electronic fault. ▶Remove the gas can and then

reinsert it. If the problem

persists, use a new gas can.

The fastening tool is hot and

doesn’t work even after a

break.

The fastener driving rate was well

above 1,200 fastenings per hour.

▶Allow the fastening tool to cool

down.

No fastener is driven (or

driven only intermittently). Ambient conditions are outside the

permissible range.

▶Make sure that the permissible

ranges, in accordance with the

technical data, are observed.

The gas can temperature is outside

the permissible range.

▶Make sure that the permissible

ranges, in accordance with the

technical data, are observed.

Gas bubbles have formed in the

gas regulating system.

▶Remove the gas can and then

reinsert it.

The tool was not lifted completely

away from the surface after driving

a fastener.

▶Lift the fastening tool completely

away from the working surface

after driving a fastener.

A fastener cannot be

removed from the fastener

guide.

A fastener has jammed in the fas-

tener magazine.

▶Release the jammed fastener.

13 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

▶Disposal of electric tools or appliances together with household waste is not permissible.

14 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

14 Français

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service. C'est la condition préalablement

requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la présente documentation ainsi que

celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement le transmettre à des tiers

avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés en combinaison avec un symbole :

DANGER ! Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la

mort.

AVERTISSEMENT ! Pour un danger imminent potentiel qui peut entraîner de graves blessures

corporelles ou la mort.

ATTENTION ! Pour attirer l'attention sur une situation pouvant présenter des dangers entraînant

des blessures corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Ces chiffres renvoient à l'illustration correspondante au début du présent mode d'emploi.

La numérotation détermine la séquence des étapes de travail dans l'image et peut se différencier

de celles des étapes de travail dans le texte.

Les numéros de position sont utilisés dans l'illustration Vue d’ensemble et renvoient aux numé-

ros des légendes dans la section Vue d'ensemble du produit.

Ce signe doit inviter à manier le produit en faisant particulièrement attention.

1.3 Symboles spécifiques au produit

1.3.1 Symboles sur le produit

Les symboles suivants sont utilisés sur le produit :

Symboles d'obligation généraux

Porter des lunettes de protection

Porter un casque antibruit

Porter un casque de protection

Recycler les déchets

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

Français 15

1.4 Identifications des textes

1.4.1 Mise en évidence de portions de texte

Les désignations et inscriptions sont mises en évidence comme suit :

‚ ‛ Désignation des organes de commande pourvus d'une inscription sur le cloueur.

« » Inscriptions sur le cloueur

1.5 Informations produit

Les produits Hilti sont conçus pour les utilisateurs professionnels et ne doivent être utilisés, entretenus et

réparés que par un personnel agréé et formé à cet effet. Ce personnel doit être au courant des dangers

inhérents à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer dangereux s'ils sont

utilisés de manière incorrecte par un personnel non qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque signalétique.

▶Inscrivez le numéro de série dans le tableau suivant. Les informations produit vous seront demandées

lorsque vous contactez nos revendeurs ou services après-vente.

Caractéristiques produit

Cloueur à gaz GX 3

Génération 01

N° de série

1.6 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit décrit ici est conforme aux

directives et normes en vigueur. Une copie de la Déclaration de conformité se trouve en fin de la présente

documentation.

Pour obtenir les documentations techniques, s'adresser à :

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sécurité

2.1 Consignes de sécurité

Travail en toute sécurité avec le cloueur

▶Si le cloueur est appuyé contre une partie du corps, un déclenchement d'un tir par mégarde peut

entraîner de graves blessures. Ne jamais appuyer le cloueur contre la main ou contre toute autre

partie du corps.

▶Lors du montage des fixations spécifiques aux applications sur le canon (p. ex. rondelles, colliers de

fixation, attaches, etc.), un déclenchement d'un tir par mégarde peut entraîner de graves blessures. Ne

jamais appuyer une main ou une partie du corps contre le canon lors du montage des fixations

spécifiques aux applications sur le canon.

▶Ne jamais diriger le cloueur vers soi ou vers une autre personne.

▶Lors du maniement du cloueur, garder les bras fléchis (ne pas tendre les bras).

▶Restez vigilant, surveillez ce que vous faites. Faites preuve de bon sens en utilisant le cloueur.

N'utilisez pas le cloueur si vous êtes fatigué ou après avoir consommé de l'alcool, des drogues ou

avoir pris des médicaments. Un moment d'inattention lors de l'utilisation du cloueur peut entraîner de

graves blessures.

▶Lors du retrait du poussoir à clous, toujours veiller à ce qu'il s'encliquette.

▶Lors du déblocage de l'enclenchement de sécurité, guider le poussoir à clous vers l'avant afin

d'éviter qu'il ne se dégage trop rapidement. L'utilisateur risque de se coincer les doigts.

▶Ne pas implanter d'éléments de fixation dans un matériau support trop dur, comme de l'acier soudé

ou de l'acier coulé. Une implantation dans ces matériaux peut entraîner des ratés de tir ou rendre les

éléments de fixation cassants.

▶Ne pas implanter d'éléments de fixation dans un matériau support trop mou, comme du bois ou du

placoplâtre. Une implantation dans ces matériaux peut entraîner des ratés de tir et des perforations du

matériau support.

▶Ne pas implanter d'éléments de fixation dans un matériau support trop fragile, comme du verre ou du

carrelage. Une implantation dans ces matériaux peut entraîner des ratés de tir et une projection d'éclats

du matériau support.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

16 Français

▶Avant d'implanter, vérifier qu'il n'y ait aucun risque de blesser une personne ou d'endommager des

objets à l'arrière du matériau support.

▶Actionner la détente uniquement lorsque le cloueur est complètement appuyé contre le matériau support,

de telle sorte que le canon rentre jusqu'en butée dans le cloueur.

▶Porter impérativement des gants de protection lorsque des opérations d'entretien doivent être

effectuées sur un cloueur chaud.

▶En cas de cadences de tir élevées pendant une période prolongée, les surfaces hors de la partie

préhensible risquent de devenir brûlantes. Porter des gants de protection contre les brûlures.

▶En cas de surchauffe du cloueur, retirer la cartouche de gaz et laisser le cloueur refroidir. Ne pas

dépasser la cadence de tir maximale.

▶Pendant le tir, le matériau peut s'écailler ou des fragments du matériau de bande-chargeur peuvent

être projetés. Les éclats de matière peuvent entraîner des blessures corporelles et aux yeux. Utiliser

des lunettes de protection, un casque antibruit et un casque de protection appropriés. Le fait

de porter des équipements de protection personnels tels que masque anti-poussières, chaussures de

sécurité antidérapantes, casque de protection ou des lunettes de protection et une protection acoustique

appropriées, suivant le travail à effectuer, réduit le risque de blessures. Les autres personnes se trouvant

à proximité doivent également porter des lunettes de protection et un casque de protection.

▶Porter un casque antibruit approprié (voir les données d'émissions acoustiques dans les caractéristiques

techniques). L'implantation des éléments de fixation est déclenchée par la mise à feu d'un mélange

air-gaz. Les nuisances sonores ainsi générées peuvent entraîner une perte d'acuité auditive. Même les

personnes environnantes doivent porter un casque antibruit approprié.

▶Toujours maintenir le cloueur fermement et perpendiculairement au matériau support pour déclencher

un tir. Cela contribue à ce que l'élément de fixation ne soit pas dévié du matériau support.

▶Ne jamais implanter un deuxième élément de fixation au même endroit. Cela risque de rendre les

éléments de fixation cassants et de les coincer.

▶Ne jamais implanter un goujon ou un clou une deuxième fois. En cas de réutilisation, il y a risque de

casse des éléments de fixation ou de blessures.

▶Toujours retirer la cartouche de gaz ( → Page 21) et vider le chargeur ( → Page 21) avant de remplacer le

chargeur, de procéder aux travaux de nettoyage, de service et d'entretien, ainsi qu'avant le stockage et

le transport, ou si le cloueur est laissé sans surveillance.

▶Après utilisation, poser l'appareil à plat sur le sol. Un appareil installé au bout d'un prolongateur ou un

appareil posé contre un mur peut provoquer des blessures en tombant.

▶Lors de l'abaissement du cloueur, ne pas tenir par l'extrémité arrière l'appareil installé au bout d'un

prolongateur. Compte tenu de l'importante force de levier, il y a risque de perdre le contrôle du fait des

mouvements pivotants du cloueur. Ceci risque de provoquer des blessures ou des dommages matériels.

▶Vérifier que le cloueur et les accessoires ne sont pas endommagés, pour assurer un fonctionnement

sans défaillances et conforme à sa destination. Vérifier que toutes les pièces mobiles fonctionnent

parfaitement et ne coincent pas, et que les pièces ne sont pas abîmées. Toutes les pièces doivent être

montées correctement et remplir toutes les conditions propres à garantir le parfait fonctionnement du

cloueur. Les dispositifs de sécurité et les pièces endommagés doivent être réparés ou remplacés de

manière professionnelle par le S.A.V. Hilti , sauf indication contraire dans le mode d'emploi.

▶Ne faire réparer le cloueur que par un personnel qualifié et seulement avec des pièces de rechange

d'origine. Ceci permet d'assurer la sécurité du cloueur.

▶Toute manipulation ou modification du cloueur est interdite.

▶Ne pas utiliser le cloueur dans des endroits présentant un danger d'incendie ou d'explosion.

▶Prêter attention aux influences de l'environnement. Protéger le cloueur des intempéries, et ne pas

l'utiliser dans un environnement humide ou mouillé.

▶Utiliser le cloueur uniquement dans des emplacements bien aérés.

▶Utiliser les combinaisons de canon et d'éléments de fixation appropriées. Une combinaison erronée

risque d'endommager le cloueur ou de nuire à la qualité de la fixation.

▶Toujours respecter les consignes d'utilisation.

Risques liés au courant électrique

▶Avant d'entamer les travaux, contrôler l'espace de travail, p. ex. à l'aide d'un détecteur de métaux, afin

de vérifier l'absence de câbles ou gaines électriques, conduites de gaz ou d'eau cachés.

▶Tenir le cloueur uniquement par la poignée isolée s'il y a un risque lors des travaux de toucher des câbles

électriques cachés. Le contact avec un câble sous tension risque de mettre les parties métalliques de

l'appareil sous tension et de provoquer une décharge électrique.

Consignes quant au maniement du gaz utilisé

▶Respecter les consignes d'utilisation figurant sur la cartouche de gaz et les informations descriptives qui

l'accompagnent.

Printed: 06.11.2018 | Doc-Nr: PUB / 5261692 / 000 / 01

La page charge ...

Hilti GX 3 Manuel utilisateur

Hilti GX 3 Manuel utilisateur

dans d''autres langues

Documents connexes