Modern Forms WS-W35516 Omni Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
WS-W35516 Omni
Taper
Mode d'emploi
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2015 1
INSTALLATION INSTRUCTION
Omni - Exterior
WS-W35516
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
F1 H1
Wire
Connector
Qty: 3 pcs
Safety Cable
Qty: 1pc
Wood Screw
Qty: 2 pcs
I1 J1 K1D1 L1 N1
Anchor
Qty: 2 pcs
Junction Box Screw
Qty: 2pcs + 1 extra
Mounting Screw
Qty: 1 extra
Fixture Screw
Qty: 4 pcs
Gasket
Qty: 1 Extra
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2015 2
INSTALLATION INSTRUCTION
Omni - Exterior
WS-W35516
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Junction Box
Caulking
Fig.3 Sealing
PREPARATION
- Shut o the power at the circuit breaker and remove existing xture, including the mounting hardware.
- Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (FIG. 1)
1. Drill the holes in the proper position on the wall according to the key holes located. Insert plastic anchors (L1) into the wall.
2. Secure the mounting plate (A1) to the junction box using junction box screws (J1). Fasten mounting plate (A1) to the wall using the wood
screws (I1).The side of the mounting plate marked “GND” must be face out.
3. Put the glass sitting on the xture. Secure the front xture bar onto the xture using screws (H1) and washer (G1).
Make sure the safety cable (N1) screwed on right location. Note: Caulk the xture srew (H1) using silicone for wet location
4. Hang the hook of safety cable (N1) onto the mounting plate (A1).This will allow for xture to be supported while wire connection is made.
CONNECTING THE WIRES (FIG. 2)
5. Connect the xture wires with the supply wires as shown in Fig. 2. Make sure that all wire connectors (K1) are secured. If your outlet box has
a ground wire (green or bare copper), connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate (A1) using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
6. Place the xture over the mounting plate (A1) and secure with the mounting screws (F1) and the gasket (D1).
COMPLETING THE INSTALLATION (FIG. 3)
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline
the outside of xture back plate where it meets the wall and the xture screw (H1) using silicone. Leave a space at the bottom to allow
moisture to escape. (Fig.3)
Technology Upgraded
No Driver Required
Driver
(Please direct wire with 120V AC)
Junction Box
Key Hole
Mounting Plate
Gasket
Mounting
Screw
Washer
Screw
Wood
Screw
Junction
Box Screw
Wire
Connector
Anchor
Safety Cable
Glass
Front Fixture Bar
D1
F1
A1
N1
K1
L1
J1 I1 H1
G1
N1
Fig.1
Back Plate Dimensions
5 5/8”
1 3/8”
10 1/4”
1 3/4”
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2015 3
INSTALLATION INSTRUCTION
Omni - Exterior
WS-W35520
HARDWARE
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
F1 H1
Wire
Connector
Qty: 3 pcs
Safety Cable
Qty: 1pc
Wood Screw
Qty: 2 pcs
I1 J1 K1D1 L1 N1
Anchor
Qty: 2 pcs
Junction Box Screw
Qty: 2pcs + 1 extra
Mounting Screw
Qty: 1 extra
Fixture Screw
Qty: 4 pcs
Gasket
Qty: 1 Extra
Modern Forms
www.modernforms.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. AUGUST, 2015 4
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig.2 Wiring
Junction Box
Caulking
Fig.3 Sealing
PREPARATION
- Shut o the power at the circuit breaker and remove existing xture, including the mounting hardware.
- Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (FIG. 1)
1. Drill the holes in the proper position on the wall according to the key holes located. Insert plastic anchors (L1) into the wall.
2. Secure the mounting plate (A1) to the junction box using junction box screws (J1). Fasten mounting plate (A1) to the wall using the wood
screws (I1).The side of the mounting plate marked “GND” must be face out.
3. Put the glass sitting on the xture. Secure the front xture bar onto the xture using screws (H1) and washer (G1). If the glass is deection
when sitting on the xture, you could regulate the glass by adjusting the height of the adjustable screws (O1).
Make sure the safety cable (N1) screwed on right location. Note: Caulk the xture screw (h1) using silicone for wet location.
4. Hang the hook of safety cable (N1) onto the mounting plate (A1).This will allow for xture to be supported while wire connection is made.
CONNECTING THE WIRES (FIG. 2)
5. Connect the xture wires with the supply wires as shown in Fig. 2. Make sure that all wire connectors (K1) are secured. If your outlet box has
a ground wire (green or bare copper), connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
mounting plate (A1) using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
6. Place the xture over the mounting plate (A1) and secure with the mounting screws (F1) and the gasket (D1).
COMPLETING THE INSTALLATION (FIG. 3)
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant) to outline
the outside of xture back plate where it meets the wall and the xture screw (H1) using silicone. Leave a space at the bottom to allow
moisture to escape. (Fig.3)
Technology Upgraded
No Driver Required
Driver
(Please direct wire with 120V AC)
Junction Box
Key Hole
Mounting Plate
Gasket
Mounting
Screw
Washer
Screw
Wood
Screw
Junction
Box Screw
Wire
Connector
Anchor
Safety Cable
Glass
Front Fixture Bar
Adjustable
Screw
D1
A1
N1
O1
K1
L1
J1
I1
N1
Fig.1
INSTALLATION INSTRUCTION
Omni - Exterior
WS-W35520
Back Plate Dimensions
1 3/8”
1 3/4”
12 5/8”
6 1/4”
H1
G1
F1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Modern Forms WS-W35516 Omni Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
WS-W35516 Omni
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents