Modern Forms WS-26111 Downton Mode d'emploi

Taper
Mode d'emploi

 !"#!!$!%%&
Read all instructions before installing.
System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
Retain installation instructions for future maintenance reference.
'All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
(Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
()'Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
Lisez toutes les instructions avant l’installation.
Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
*Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 3pcs+1Extra
Mounting Screw
Qty:1 Extra
A B
1
INSTALLATION INSTRUCTIONS
+,-.")
WS-26111

Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122
 
1750 Archibald Avenue
Ontario, CA 91760

//
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
('0120%&-3
3. Remove the mounting screw (B) from the canopy.
4. The lamp can switch between three color temperatures (2700k-3000k-3500k), which can be adjusted to your preference with the switch in
the canopy (Fig.3).
5. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box.
Note: (i) using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked GND must face out.
')20%&+3
6. Connect the xture’s wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet box
has a green or bare copper ground wire, connect the driver’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
back plate using  screw provided. After wires are connected, tuck them carefully inside the junction box.
(/4')44
7. Secure the xture to the mounting back plate using the mounting screw (B).
05
Black or
Smooth
05
White or
Ribbed
05
Bare wire
(Ground)

Black
(Hot)

White
(Neutral)

Green or Bare Copper
(Ground)
0%&+%
2
INSTALLATION INSTRUCTIONS
+,-.")
WS-26111

Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122

1750 Archibald Avenue
Ontario, CA 91760

WS-26111
Back Plate Dimensions
105
8
41
8
1
3
8
1
3
4
0%&-
3000K3500K
2700K
0%&6
Junction box
Mounting plate
Wire connector
Junction box screw
Mounting screw
Fabric shade
(RPL-SHA-26111)
A
B
Ground wire
Diuser
(RPL-DIF-26111)
Glass
(RPL-GLA-26111)
  • Page 1 1
  • Page 2 2

Modern Forms WS-26111 Downton Mode d'emploi

Taper
Mode d'emploi