Chief KSA1024B Guide d'installation
- Catégorie
- Accessoires pour écran plat
- Taper
- Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Quick Connect/Disconnect Bracket
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KSA-1024
KSA-1024 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Centris™ are registered trademarks of Milestone
AV Technologies. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING:
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION:
A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING:
Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING:
Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this accessory does not exceed
40 lbs (18.14 kg). DO NOT exceed the weight limitations of
the mount being installed to the bracket or of the office
furniture being used to mount the accessory.
DIMENSIONS
5.87
149.2
4.64
117.8
2.95
75
3.94
100
2.95
75
3.94
100
.28
7.2
.77
19.7
.48
12.3 .76
19.3
.10
2.7
KSA-1024 SHOWN INSTALLED
ONTO K SERIES CENTRIS INTERFACE
KSA-1024
K SERIES
CENTRIS INTERFACE
(SOLD SEPERATELY) LOCKED
POSITION
QUICK LOCK FLAG
THUMB NUT
SECURITY SCREW PORT UNLOCKED
POSITION
KSA-1024 SHOWN
Installation Instructions KSA-1024
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
KSA-1024 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION AND PARTS
5/32"
(included)
(security)
A(1)
B(1) C(1)
M4 x 30mm
D(4) H(4)
1/2 x .194 x 3/4"
[Quick Connect/Disconnect Bracket]
(included)
(security)
5/32"
M4 x 8mm
+ Assembly kit
M4 x 12mm E(4)
M4 x 20mm F(4) G(4)
1/2 x .194 x 1/2"
#2
Installation Instructions KSA-1024
5
Assembly And Installation
Attach Quick Connect/Disconnect Bracket to
Display
1. Lay display face side down on a level, non-abrasive
surface. Lay down a cloth if necessary to avoid scratching
the screen.
2. For non-recessed mounting holes, install four M4 x 12mm
Phillips flathead machine screws (D) through corresponding
bracket holes and into holes on back of display. (See Figure
1)
Figure 1
3. For recessed mounting holes, install either four M4 x 20mm
or four M4 x 30mm Phillips flathead machine screws (E or
F) through corresponding bracket holes and four spacers (G
or H) and into holes on back of display. (See Figure 2)
Figure 2
Attach Bracket to Centris Plate
1. Make sure quick connect/disconnect bracket flag is in the
open position. (See Figure 3)
2. Place quick connect/disconnect bracket over Centris plate
making sure upper lip of bracket covers top of Centris plate.
(See Figure 3)
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this accessory does not exceed
40 lbs (18.14 kg). DO NOT exceed the weight limitations of
the mount being installed to the bracket or of the office
furniture being used to mount the accessory.
Figure 3
3. Move bracket flag to closed position. (See Figure 4)
Figure 4
(D) x 4
(A)
2
(E or F) x 4
(A)
(G or H) x 4
3
Centris head
2
flag in open position
3
(rear view)
KSA-1024 Installation Instructions
6
4. Tighten thumbnut on bracket flag to secure bracket to
Centris plate. (See Figure 5)
Figure 5
Optional Security Screw Installation
1. Use enclosed 5/32" security hex key (C) to install M4 x 8mm
button head security screw (B) into security hole on bracket.
(See Figure 6)
Figure 6
4
(B)
1
Installation Instructions KSA-1024
7
KSA-1024 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002008 REV 00
©2009 Milestone AV Technologies, a
Duchossios Group Company
www.chiefmfg.com
03/09
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P+86-755-8996 9226
F+86-755-8996 9217
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief KSA1024B Guide d'installation
- Catégorie
- Accessoires pour écran plat
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief KSA1024B Installation guide
Documents connexes
-
Chief JHS210B Guide d'installation
-
-
Chief JPP210S Guide d'installation
-
Chief JPPVB Guide d'installation
-
-
-
-
-
Chief Manufacturing PCS2051 Manuel utilisateur
-