WAC Lighting WS-15422 Mode d'emploi

Taper
Mode d'emploi

Ce manuel convient également à



Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122

1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION


WS-15422 WS-15432


• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
 Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty: 3pcs+1Extra
A
Mounting Screw
Qty: 1Extra
B
QTY:1Extra
QTY:1Extra
Conversion plate
Mounting Ring
D
C


Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122

1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION


WS-15422 WS-15432

Fixture
Junction Box
Screw
Mounting screw
Wire Connector
Junction Box
Black wire
Ground Wire
Mounting Back
plate
Ground Wire
Switch Box

Switch Box
Fixture
Junction Box Screw
Mounting screw
Mounting Ring
A
B
Wire Connector
A
Junction Box
Screw
B
C
Mounting Backplate
Conversion plate
Adapter Screw
D
E


Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122

1750 Archibald Avenue
Ontario, CA 91760
3
INSTALLATION INSTRUCTION


WS-15422 WS-15432

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

3. Remove the mounting screw (B) from the mounting plate.
4. Secure the mounting plate to the switch box using standard junction box screws that comes with the switch box.
 (i) It is recommended to use only original junction box screws or replacements provided by junction box manufacturer.
(ii) The side of the mounting plate marked “GND” must face out.
5. Secure the xture to the mounting plate using the mounting screw (B).

3. Remove the mounting screw (B) from the mounting plate.
4. Secure the mounting ring (C) to the junction box using junction box screws. The side of the mounting plate marked “GND” must face out.
5. Secure the mounting plate and conversion plate(D) to the mounting ring (C) using adapter screws (E) as shown in Fig. 2.
 (i) It is recommended to use only original junction box screws or replacements provided by junction box manufacturer.
(ii) The side of the mounting plate marked “GND” must face out.
6. Connect the xture input wires to the junction box wires (Fig. 2) using wire connectors (A) provided. Ensure all wire connectors are secure.
Connect the xture’s ground wire to the ground in the junction box; this will be either a green wire or a bare copper wire. After xture is
wired to house wires, tuck wires carefully inside the junction box.
7. Secure the xture to the mounting plate using the mounting screw (B).

Black or
Smooth

White or
Ribbed

Bare wire
(Ground)

Black
(Hot)

White
(Neutral)

Green or Bare Copper
(Ground)

Mounting Back Plate Dimensions

Junction Box
Caulking
4 1/2"
1 3/8"
1 5/8"
4 1/2"
1 3/8 "
Conversion Plate Dimensions
1 3/8"
1 3/4"
4"
Mounting Ring Dimensions
3 3/4"
2 5/8"
  • Page 1 1
  • Page 2 2
  • Page 3 3

WAC Lighting WS-15422 Mode d'emploi

Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues