Momument Grills C042177 Le manuel du propriétaire

Liquid Propane Gas Grill

Note to Consumer

Leave this Owner’s Manual in a convenient

place for future reference.

Customer Service Helpline:

For parts ordering, call:

1-888-980-4933

MFG No.: 17842

UPC No.:860448000372

Please make sure the cylinder valve

connection device shall properly and safely

mate with the connection device attached to

the inlet of the pressure regulator.

WARNING:

Read this Owner’s manual carefully and be

sure your gas grill is properly assembled,

installed and maintained. Failure to follow these

instructions could result in serious injury and/or

property damage. This gas grill is intended for

outdoor use only and is not intended to be

installed in or on recreational vehicles or boats.

Note to Installer

Leave this Owner’s Manual with the customer

after delivery and/or installation.

!

•Parts

•Assembly

•Safety Rules

•Use and Care

•Troubleshooting

ASSEMBLY & OPERATING INSTRUCTIONS

C042177

WARNING

Your grill will get very hot. Never lean over the

cooking area while using your grill. Do not touch

cooking surfaces, grill housing, lid or any other

grill parts while the grill is in operation, or until

the gas grill has cooled down after use.

Failure to comply with these instructions may

result in serious bodily injury.

One-Year Full Warranty on Grill

If this grill fails due to defective material or

workmanship within one year from the date of

purchase, call 1-888-980-4933 to arrange for a free

repair (or replacement if repair proves impossible).

8-Year Limited Warranty on Stainless Steel

Burners

For eight years from the date of purchase, any

stainless steel burner that rusts through will be

replaced free of charge. After the first year from the

date of purchase, you pay for labor if you wish to have

it installed.

All warranty coverage excludes ignitor batteries and

grill part paint loss, discoloration or rusting, which are

either expendable parts that can wear out from normal

use within the warranty period, or are conditions that

can be the result or normal use, accident or improper

maintenance,

All warranty coverage is void if this grill is ever used

for commercial or rental purposes.

All warranty coverage applies only if this grill is used in

the United States.

This warranty gives you specific legal rights, and you

may have other right which vary from state to state.

The warranty is only valid for original purchasers with

proof of purchase from authorized retailers. Any

product bought second hand or through an

unauthorized retailer, will not be covered by

warranty. It is the duty of the purchaser to verify that a

retailer is authorized. A purchase on Amazon or other

marketplace internet retailer from any entity other than

Monument Grills is not an original purchase and will

not qualify for a warranty

WARNING

Combustion by products produced when using

this product contain chemicals known to the

State of California to cause cancer, birth defects,

or other reproductive harm.

WARNING

Failure to comply with these instructions could

result in a fire or explosion that could cause

serious bodily injury, death, or property damage.

WARNING

1. Do not store or use gasoline or

other flammable liquids or

vapors in the vicinity of this or

any other appliance.

2. An LP cylinder not connected for

use shall not be stored in the

vicinity of this or any other

appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away

from the appliance and

immediately call your gas

supplier or your fire department.

Grill Installation Codes

The installation must conform with local codes or, in

the absence of local codes, with either the national fuel

gas code, ANSI Z 223.1/NFPA S4, Natural gas and

propane installation code, CSA B149.1, or propane

storage and handling code, B149.2, or the standard for

Recreational vehicles, ANSI A 119.2, and CSA Z240

RV series recreational vehicle code, as applicable.

LP gas grill models are designed for use with a

standard 20 lb. Liquid Propane Gas tank, not included

with grill. Never connect your gas grill to an LP gas

tank that exceeds this capacity.

!

2

Grill Warranty

Safety Precautions

!

Table of Contents

Warranty------------------------------------------------2

Safety Precautions--------------------------------2~4

Hardware List------------------------------------------5

Parts Diagram -----------------------------------------6

Parts List------------------------------------------------7

Assembly Instructions---------------------------8~17

Lighting Instructions----------------------------17~19

Cleaning and Maintenance-------------------20~21

Troubleshooting--------------------------------------21

Cooking Instruction----------------------------------22

Cooking Chart----------------------------------------23

• Have your LP gas tank filled by a reputable

propane gas dealer and visually inspected and re-

qualified at each filling.

• Do not store a spare LP gas tank under or

• Never fill the tank beyond 80 percent full . If this

information is not followed exactly a fire causing

death or serious injury may occur.

• Always keep LP gas tanks in an upright position.

• Do not store (or) or use gasoline or other

flammable vapors and liquids in the vicinity of this

gas grill.

• Do not subject the LP gas tank to excessive heat.

• Never store an LP gas tank indoors. If you store

your gas grill in the garage or other indoor

location, always disconnect the LP gas tank first

and store it safely outside.

• Place dust cap on cylinder valve outlet whenever

the cylinder is not in use. Only install the type of

dust cap on the cylinder valve outlet that is

provided with the cylinder valve. Other types of

caps or plugs may result in leakage of propane.

• LP gas tanks must be stored outdoors in a well-

ventilated area and out of reach of children.

Disconnected LP gas tanks must not be stored in

a building, garage or any other enclosed area.

• When your gas grill is not in use the gas must be

turned off at the LP gas tank.

• The pressure regulator and hose assembly must

be inspected before each use of the grill. If there

is excessive abrasion or wear or if the hose is cut,

it must be replaced prior to the grill being used

again.

• Keep the gas regulator hose away from hot grill

surfaces and dripping grease. Avoid unnecessary

twisting of hose. Visually inspect the hose prior to

each use for cuts, cracks, excessive wear or

other damage. If the hose appears damaged do

not use the gas grill. Call 1-888-980-4933 for

assistance.

•Never light your gas grill with the lid closed or

before checking to ensure the burner tubes are

fully seated over the gas valve orifices.

•Never allow children to operate your grill.

A tank of approximately 12 inches in diameter by 18-

1/2 inches high is the maximum size LP gas tank to

use. You must use an OPD gas tank which offers

an Overfill Prevention Device.

This safety feature prevents the tank from being

overfilled which can cause malfunction of the LP gas

tank, regulator and/or grill.

The LP gas tank must be constructed and marked in

accordance with specifications of the U.S. Dept. of

Transportation (DOT). In Canada, the LP gas tank

must meet the National Standard of Canada ,Can

CSA –B339 , Cylinders , spheres and Tubes for

Transportation of Dangerous Goods and

Commission .

1. The LP gas tank must have a shutoff valve,

terminating in an LP gas supply tank valve outlet,

that is compatible with a Type 1 tank connection

device. The LP gas tank must also have a safety

relief device that has a direct connection with the

vapor space of the tank.

2. Always keep LP gas tanks in an upright position.

The tank supply system must be arranged for vapor

withdraw.

3. The LP gas tank used must have a collar to

protect the tank valve.

Proper Placement and Clearance of Grill

Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area. Your gas grill

is to be used outdoors only, at least 24 inches from

the back and side of any combustible surface. Your

gas grill should not be used under overhead

combustible construction . Do not obstruct the flow of

ventilation air around the gas grill housing.

• Do not install this outdoor gas grill in or on

recreational vehicles or boats

• Keep outdoor gas grill area clear and free from

combustible materials, gasoline and other flammable

vapors and liquids

• Do not obstruct the flow of combustion and

ventilation air. Check for this each time prior to using

grill.

•Never connect an unregulated LP gas tank to your

gas grill. The gas regulator assembly supplied with

your gas grill is adjusted to have an outlet pressure

of 11” water column (W.C.) for connection to an LP

gas tank.

• Only use the regulator and the hose assembly

supplied with your gas grill. Replacement regulators

and hose assemblies must be those specified in this

manual.

3

Safety Precautions

WARNING

A strong gas smell, or the hissing sound of gas

indicates a serious problem with your gas grill or

the LP gas tank. Failure to immediately follow the

steps listed below could result in a fire or

explosion that could cause serious bodily injury,

death, or property damage.

• Shut off gas supply to the gas grill.

• Turn the control knobs to OFF position.

• Put out any flame with a proper fire extinguisher.

• Open Grill Lid.

• Get away from the LP gas tank.

• Do not try to fix the problem yourself.

• If odor continues or you have a fire you can not

extinguish, call your fire department. Do not call

near the LP gas tank because your telephone is

a form of electrical device and could create a

spark resulting in fire and/or explosion.

CAUTION: Spiders and small insects occasionally

spin webs or make nests in the grill burner tubes

during transit and warehousing. These webs can lead

to gas flow obstruction which could result in a fire in

and around burner tubes. This type of fire is known as

“FLASH-BACK” and can cause serious damage to

your grill and create an unsafe operating condition for

the user.

Although an obstructed burner tube is not the only

cause of “FLASH-BACK”, it is the most common

cause.

To reduce the chance of “FLASH-BACK”, you must

clean the burner tubes before assembling your grill,

and at least once a month in late summer or early fall

when spiders are most active. Also perform this

burner tube cleaning procedure if your grill has not

been used for an extended period of time.

See Cleaning Burner Tubes and Ports on page # 15

NOTE: The normal flow of gas through the

regulator and hose assembly can create a

humming noise. A low volume of noise is perfectly

normal and will not interfere with operation of the

grill. If humming noise is loud and excessive you

may need to purge air from the gas line or reset

the regulator excess gas flow device. This purging

procedure should be done every time a new LP

gas tank is connected to your grill. For help with

this procedure refer to page 14, Item 4 of “If Grill

Still Fails To Light”, or call the Customer Service

Helpline 8 AM to 5 PM PST at: 1-888-980-4933.

Visually check the burner flames prior to each use. The

flames should look like picture, if they do not, refer to the

cleaning burner tubes and ports, see page 15 of this

manual.

!

4

CAUTION: Beware of Flash-Back

Burner Flame Check

The following table illustrates a breakdown of the hardware pack. It highlights what components are used in

the various stages of assembly.

5

Contents for Hardware Pack

Tools required for assembly

Philips Head Screwdriver (not included).

Note: The left and right sides of the grill are on your left and right as you face the front of the grill.

Philips Head Screwdriver

A

5/32"x12mm 11 pcs

B

1/4"x15mm 12 pcs

C

2 pcs

D

1/4'' 4 pcs

6

Model 17842 Parts Diagram

For assembly questions, call:

1-888-980-4933

To make sure you obtain the correct replacement

parts for your gas grill, please refer to the part

numbers on this page.

Important: Use only parts listed above. When ordering

parts, providing the following information:

1. Model #

2. Part Number (see PART# in chart)

3. Part Description

4. Quantity of parts needed

7

Model 17842 Parts List

Important: Keep this Owner’s Manual for

convenient reference and for part replacement.

seq.

NO. appellation qty Material code seq.

NO. appellation qty Material

code

1 Main Lid 1 D010012908 36 Door Magnet 2 A0201249

2 Temperature Gauge 1 A0212824 37 Cart Frame, Front 1 D010012721

3 Temperature Gauge Seat 1 A0212825 38 Back Panel, Bottom 1 D010012748

4 Main Lid Screw 2 A0407131 39 Bottom Panel 1 D010012098

5 Main Lid Handle 1 D010010251 40 Side Panel, Right 1 D010012903

6 Hood Buffer 4 A0201340 41 Battery Box 1 A0212663

7 Warming Rack 1 A0212856 42 Spindle Below Door Panel 2 A0212557

8 Cooking Grid With Hole 3 A0212804 43 Spacing Screw Below Door Panel 2 A02120079

9 Flame Tamer 4 D010012307 44

Cart

Bottom

Panel

Front

Cummerbund Strip

1 D010012063

10 Clamp Spring 4 A0212873 45 Triangle Bracket, Left 2 D010012745

11 Main Burner 4 A0212926 46 Swivel Caster Fixing Plug 4 A0212805

12 Main Burner Igniter Wire 4 D010012900 47 Swivel Caster 4 A0211004

13 Back Panel, Top 1 D010012737 48 Gas-jar Fixing Line 1 A0212837

14 Grease Box Bracket 1 A0212838 49 Lighting Rod 1 A0212835

15 Grease Box 1 D010012705 50 Door Handle 2 D010012747

16 Grease Tray 1 D010012072 51 Front Door 2 D010012094

17 Side Burner Lid Hinge Rod 1 A0212534 52 LED Lamp Seat-USB2.0 1 A02120032

18 Side Burner Lid 1 D010007598 53 LED Lamp Switch 1 A0212627

19 Side Burner Cooking Grid, Right 1 A0212248 54 LED Lamp Circuit 1 D010013690

20 Side Burner, Right 1 A0212533 55 Main Control Panel 1 D010014390

21 Side Burner Tray 1 D011006420 56 Main Control Panel Frame 1 D010012054

22 Side Burner Orifice Bracket 1 D019706920 57 Gas Connector 1 A0212830

23 Side Burner Igniter, Right 1 A0212436 58 Gas Connector Fixing Panel 1 D010012298

24 Side Burner Igniter Wire, Right 1 A0212869 59 Main Burner Flex Gas Line 1 A0212829

25 Side Shelf, Right 1 D010014389 60 Regulator, LP 1 A0212831

26 Hook 4 A0212538 61 Main Manifold 1 A02120087

27 Side Burner Orifice 1 A0212828 62 Main Gas Valve 4 A0212862

28 Side Burner Flex Gas Line, 250 1 A020021 63 Front Baffle 1 D010012052

29 Side Burner Flex Gas Line, 480 1 A02120090 64 Control Panel Fixing Panel, Left 1 D010012050

30 Side Burner Gas Vavle, Right 1 A02120088 65 Control Panel Fixing Panel, Right 1 D010012051

31 Control Knob Base 5 D010012905 66 Side Shelf, Left 1 D010012770

32 LED Lamp Panel 5 A0212777 67 Logo 1 A0212808

33 Control Knob 5 A0212922 Manual 1 C042177

34 Pulse Igniter Module 1 A0212934 Hardware Pack 1 D010012753

Figure 2

8

Assembly Instructions

Figure 1

Please insert Part No.47 into the bottom plate.

Half screw out the screws in the

bottom plate, then put Part No.35 and

Part No.40 onto the relevant screw

holes and screw tightly.

Figure 4

Figure 3

9

4 x

B

Install Part No.38 onto the relevant place

with four B screws.

Half screw out the screws in the bottom

and side plates, then put Part No.45 onto the relevant

screw holes and screw tightly.

10

Figure 5

Figure 6

4 x

A

Install Part No.37 onto the relevant place with

four A screws shown in Figure 5.

Attention: magnet downward.

Figure 7.1

11

Figure 8.1 Figure 8.2

Figure 7.2

2 x B

2 x D

4 x

B

Screw the grill body and the

cart tightly with four B screws. (Figure 7.1)

1.Half screw out the three big screws outside the grill body,

then put Part No.25 onto the relevant screw holes and screw tightly.

2.Screw Part No.25 tightly with B screw and D spacer inside the grill body.

Figure 9

Figure 10

12

1. Insert the wire of Part No.23.

1. Insert Part No.30, Part No.31, Part No.32 and Part No.33 as the figure shows.

2. Insert the wire as the figure shows.

Figure 11

Figure 12.1 Figure 12.2 Figure 12.3

13

2 x B

2 x D

Half screw out the screw in Part No.27,

then put it into the hole of Part No.22

and screw tightly.

1.Half screw out the three big screws on the grill body,

then put Part No.66 onto the relevant screw holes and screw tightly.

2.Screw Part No.66 tightly with B screw and D spacer inside the grill body.

Figure 13.1

Figure 14.1

14

Figure 14.2 Figure 14.3

Figure 13.2

1 x

A

CC

Fixed Part No.58 onto the right plate with one A screw.

4 x

A

1.Install Part No. 50 onto Part No.51 with A screws. (Figure 14.1)

2.Put the C part into the relevant hole in the bottom plate. (Figure 14.2)

3.Put Part No.51 into the C part. (Figure 14.2)

4.Then put the door into by pressing the flexible axis upward.

Figure 15.1

Figure 16

15

Figure 15.2

Put Part No. 7, Part No. 8 , Part No. 9 and Part No. 49 into the relevant place.

2 x

A

1.Install Part No.14 onto Part No.16 with two A screws. (Figure15.1)

2.Put Part No.15 into Part No.14. (Figure15.1)

3.Put the grease tray into the grill body. (Figure15.2)

Figure 17

16

Connect Part No.54 to Part No.41.

1 2 3

Figure 18.1 Figure 18.2

1.Install Part No. 48 onto the bottom plate. (Figure18.1)

2.Install Part No. 26 onto the side plate. (Figure18.2)

Connecting LP Gas Tank to LP Grill

1. Place foot ring of 20 lb tank into the hole in bottom

panel. Make sure the tank valve is in OFF

position.(Fig.20).

2. Check the tank valve to ensure it has proper

external mating threads to fit the hose and regulator

assembly provided.

3. Make sure all burner valves are in OFF position.

4. Inspect the valve connection port and regulator

assembly. Look for damage or debris. Remove any

debris. Inspect hose for damage. Never use

damaged or plugged equipment.

5. When connecting regulator and hose assembly to

tank valve hand tighten quick coupling nut clockwise

to a full stop (Fig.19) Do not use a wrench to tighten

because it could damage the quick coupling nut and

result in a hazardous condition.

6. Open tank valve fully (counterclockwise). Use a

soapy water solution to check all connections for

leaks before attempting to light your grill. If a leak is

found, turn tank valve off and do not use your grill

until the leak is repaired.

CAUTION: When the appliance is not in use, gas

must be turned off at the supply tank.

17

Figure 20

Regulator Connection

Figure 19

Congratulations

Your gas grill is now ready for use. Before the

first use and at the beginning of each season

(and whenever the LP gas tank has been

changed):

1. Read all safety, lighting and operating

instructions.

2. Check gas valve orifices, burner tubes and

burner ports for any obstructions.

3. Perform gas leak check according to

instructions found on next page of the manual.

LIGHTING INSTRUCTIONS FOR SIDE BURNER

1. Open side burner lid fully.

2. Push and turn side burner knob to IGNITE/HI

position. At the same time, press and hold

electronic ignition button for 3 to 5 seconds to

light burner.

3. If the side burner does not light after 5 seconds,

turn knob to OFF. Turn gas OFF at LP tank and

wait 5 minutes for gas to clear. Then turn gas

ON at tank and repeat step 2.

4. If burner still does not light, see Match Lighting

section and If Grill Still Fails to Light section on

following page.

Grill Lighting Instructions for Main Burners

1. Do not smoke while lighting grill or checking gas

supply connections.

2. Be sure that LP gas tank is sufficiently full.

3. Be sure all gas connections are securely tightened.

4. Turn on gas supply

5. Open the grill main lid and side burner lid.

6. Push and turn any main burner knob to IGNITE/HI

position, at the same time, press and hold

electronic ignition button for 3 to 5 seconds to light burner.

7. To light burners, push and turn burner knob (s)

to IGNITE/HI. At the same time, press and hold

electronic ignition button for 3 to 5 seconds to light

burner. Adjust knob (s) to desired setting.

8. If the burner does not light after 5 seconds, turn

knob to OFF. Turn gas OFF at LP tank and wait 5

minutes for gas to clear. Then turn gas ON at tank

and repeat step 6.

9. If burner still does not light, see Match Lighting

section and If Grill Still Fails to Light section on

following page.

1. Make a 50/50 (soap/water) mild soap solution.

2. Turn the control knobs to full OFF position; then

turn gas ON at supply tank.

3. Apply the soap solution with a clean brush to all

gas connections. See below. If growing bubbles

appear in the solution the connections are not

properly sealed. Check each fitting and tighten or

repair as necessary.

4. If you have a gas connection leak you cannot

repair, turn gas OFF at supply tank, disconnect

fuel line from your grill and call 1-888-980-4933 or

your gas supplier for repair assistance.

5. Also apply soapy solution to the tank seams. See

below. If growing bubbles appear, shut tank OFF

and do not use or move it! Contact an LP gas

supplier or your fire department for assistance.

WARNING

Failure to open grill lid during the lighting

procedure could result in a fire or explosion

that could cause serious bodily injury, death,

or property damage.

!

18

USING THE SIDE BURNER

Inspect the gas supply hose prior to turning the gas

“ON”. If there is evidence of cuts, wear or abrasion,

it must be replaced prior to use. Do not use the

side burner if the odor of gas is present.

WARNING: Always keep your face and body as

far away from the burner as possible when

lighting.

Gas Connection Leak Check

Gas Tank Leak Check

Checking for LP gas leaks

Never test for leaks with a flame. Prior to first use, at

the beginning of each season, or every time your LP

gas tank is changed, you must check for gas leaks.

Grill Lighting Instruction

WARNING

Never lean over the grill cooking area while

lighting your gas grill. Keep your face and body

a safe distance (at least 18 inches) from the

cooking grid surface when lighting your grill by

match.

If Grill Still Fails To Light

1. Check gas supply and connections for leaks. Check

that all wire connections are secure.

2. Repeat basic lighting procedure. If your grill still fails

to operate, turn the gas off at source, turn the control

knobs to OFF, then check the following:

• Misalignment of burner tubes over orifices

Correction: Reposition burner tubes over orifices.

•Obstruction in gas line

Correction: Remove fuel line from grill. Do not smoke!

Open gas supply for 1 second to clear any obstruction

from fuel line. Close off gas supply at source and

reconnect fuel line to grill.

• Plugged orifice

Correction: Remove burners from grill, carefully lift

each burner up and away from gas valve orifice.

Remove the orifice from gas valve and gently clear any

obstruction with a fine wire. Then reinstall all orifices,

burners, and cooking components.

3. If an obstruction is suspected in gas valves, please

call for repair service at 1-888-980-4933 .

4. If the grill still does not light you may need to purge air

from the gas line or reset the regulator excess gas flow

device. Note: This procedure should be done every time

a new LP gas tank is connected to your grill.

To purge air from your gas line and/or reset the

regulator excess gas flow device:

• Turn the control knob to OFF position.

• Turn off the gas at the tank valve.

• Disconnect regulator from LP gas tank.

• Let unit stand for 5 minutes.

• Reconnect regulator to the LP gas tank.

• Turn the tank valve on slowly until ¼ to ½ open.

• Open the grill lid.

• Set control knobs to OFF. Push and turn any control

knob to HIGH.

• Turn control knobs to HIGH until all the burners are lit

• You may start to use the grill

5. If all checks or corrections have been made and you

still have questions about operating your gas grill, call

the Customer Service Helpline 8 AM – 5 PM PST,

Monday through Friday at 1-888-980-4933

WARNING

Should a “FLASH-BACK” fire occur in/or

around the burner tubes, follow the instructions

below. Failure to comply with these instructions

could result in a fire or explosion that could

cause serious bodily injury, death, or property

damage.

• Shut off gas supply to the gas grill.

• Turn the control knobs to OFF position.

• Put out any flame with a proper fire extinguisher.

• Open grill lid.

• Once the grill has cooled down, clean the burner

tubes and burners according to the cleaning

instructions found on page 15.

!

19

Manually Lighting Your Grill by Match

1. Take the manual lighting stick

2. Insert a match into the lighting stick.

3. Follow steps 1 through 5 of the Basic Lighting

Procedure.

4. Light the match and extend the lighting stick to

cooking grid surface.

5. Turn the desired control knob to the HI/position

setting to release gas. The burner should light

immediately.

!

To ensure a proper working unit the following proper

care and maintenance is suggested.

Cleaning Cooking Grids

We suggest you wash your cooking grids in a mild soap

and warm water solution. You can use a wash cloth or

soft brush to clean your cooking grids.

Cleaning Heat diffusers

Periodically you should wash the heat diffusers in a

soap and warm water solution. Use a soft brush to

remove stubborn burnt-on cooking residue. The heat

diffusers should be dry before you reinstall them.

Cleaning Grease Tray

The grease tray should be emptied and wiped

down periodically and washed in a mild

detergent and warm water solution. A small

amount of sand or cat litter may be placed in

bottom of grease tray to absorb the grease.

Check the grease tray frequently, don’t allow

excess grease to accumulate and overflow out of the

grease tray.

Annual Cleaning of Grill Interior

Burning-off the grill after every use will keep it ready for

your next use. However, once a year you should give

the entire grill a thorough cleaning to keep it in top

operating condition. Follow these steps.

1. Turn all burner valves to full OFF position.

2. Turn LP gas tank valve to full OFF position.

3. Detach LP gas hose and regulator assembly from

your gas grill. Inspect for any damage and replace as

necessary with manufacturer replacement part number

found on parts list.

4. Remove and clean heat diffusers, cooking grids and

grill burners.

5. Cover each gas valve orifice with aluminum foil.

6. Brush inside and bottom of grill with a nylon brush,

and wash with a mild soap and warm water solution.

Rinse thoroughly and let dry.

7. Remove the aluminum foil, then reinstall heat

diffusers, and cooking grids.

8. Reconnect gas source and observe burner flame for

correct operation.

Cleaning Exterior Surface

•We suggest you wash your grill using a mild soap and

warm water solution. You can use a wash cloth or

sponge for this process. Do not use abrasives or a

brush that might remove finish during the cleaning

process.

Cleaning Exterior Stainless Steel Surfaces

•Weathering and extreme heat can cause exterior

stainless steel surfaces to turn tan in color. Machine

oils used in manufacturing process of stainless steel

can also cause this tanning color. Use a stainless

steel cleaner to polish stainless steel surfaces of

your grill. Never use abrasive cleaners or scrubbers

because they will scratch and damage your grill.

20

Cleaning Burner Tubes and Burner Ports

To reduce the chance of “FLASH-BACK” the procedure

below should be followed at least once a month in late

summer or early fall when spiders are most active or

when your grill has not been used for a period of time.

1. Turn all burner valves and gas tank valve to off

position.

2. Detach the LP gas regulator assembly from your gas

grill.

3. Remove cooking grids, heat diffusers, and grease

tray from the grill.

4. Remove the screws from the underside of each

burner and lift the burners up and away from the gas

valve orifice.

5. Using a bent stiff wire in the shape of a hook , air

hose or a bottle brush, run it through the burner tube

and inside several times to remove any debris.

6. Replace burners, see illustration below.

WARNING

The location of the burner tube with respect to the

orifice is vital for safe operation. Check to ensure the

orifice is inside the burner tube before using the gas

grill. If the burner tube does not fit over the valve

orifice, lighting the burner may cause explosion

and/or fire.

!

Cleaning and Maintenance

Step 1 Step 2 Step 3

La page charge ...

Momument Grills C042177 Le manuel du propriétaire

Ce manuel convient également à

Momument Grills C042177 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents