Thermador T18ID905RP Mode d'emploi

USE & CARE GUIDE

GUIDE

D’UTILISATION

ET D’ENTRETIEN

MANUAL DE USO

Y CUIDADO

Model/Modele/Modelo

T18ID905RP

T18ID905LP

T24ID905RP

T24ID905LP

Freezer

Congélateur

Congelador

en-us

2

en Table of contents

en I ns t r uc t i o n manual

( Important safety instructions . . . . . . . . . . . . 4

Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

About these instructions . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Restriction of user group. . . . . . . . . . . . . . . . . . . . . 4

Risk of explosion. . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Risk of electric shock . . . . . . . . . . . . . . . . . . . . . . . 5

Risk of cold burns . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Risk of injury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Fire hazard/Danger due to refrigerants . . . . . . . . . . 5

Risk of fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Risk of suffocation. . . . . . . . . . . . . . . . . . . . . . . . . . 6

Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

State of California Proposition 65 Warnings . . . . . . 6

8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . 7

7 Environmental protection . . . . . . . . . . . . . . . 7

Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Old appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5 Installation and connection . . . . . . . . . . . . . . 7

Contents of package. . . . . . . . . . . . . . . . . . . . . . . . 7

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the appliance . . . . . . . . . . . . . . . . . . . . . . 7

Check built-in cut-out. . . . . . . . . . . . . . . . . . . . . . . . 7

Side-by-side installation . . . . . . . . . . . . . . . . . . . . . . 7

Saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Before using for the first time . . . . . . . . . . . . . . . . . 9

Water connection . . . . . . . . . . . . . . . . . . . . . . . . . .9

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . 9

* Getting to know your appliance . . . . . . . . . 10

Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operating controls. . . . . . . . . . . . . . . . . . . . . . . . .10

Ice and water dispenser . . . . . . . . . . . . . . . . . . . .11

Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

1 Operating the appliance . . . . . . . . . . . . . . . . 14

Switching the appliance on . . . . . . . . . . . . . . . . . . 14

Switching off and disconnecting the

appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the language . . . . . . . . . . . . . . . . . . . . . . . 14

Setting the temperature unit . . . . . . . . . . . . . . . . .14

Setting the temperature. . . . . . . . . . . . . . . . . . . . .14

Super freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Clean lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Switching ice cube production on or off . . . . . . . .15

Reset water filter counter. . . . . . . . . . . . . . . . . . . . 15

Eco mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Self-test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Setting the brightness of the control panel . . . . . .15

Switching key press sound on or off . . . . . . . . . . . 16

Setting the key volume . . . . . . . . . . . . . . . . . . . . . 16

Setting the signal tone volume . . . . . . . . . . . . . . . 16

Automatic clean lock . . . . . . . . . . . . . . . . . . . . . . 16

Automatic door opening . . . . . . . . . . . . . . . . . . . . 16

Switching the water filter counter on and off. . . . . 17

Dispenser light . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Motion sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Theater mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Resetting to the factory settings . . . . . . . . . . . . . . 17

Switching demo mode on or off . . . . . . . . . . . . . . 17

Sabbath mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

M Alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Temperature alarm . . . . . . . . . . . . . . . . . . . . . . . . 18

o Home Connect. . . . . . . . . . . . . . . . . . . . . . . . 19

Setting up a home network. . . . . . . . . . . . . . . . . . 19

Connecting the refrigerator to the

Home Connect app . . . . . . . . . . . . . . . . . . . . . . . 19

Installing updates for the Home

Connect software . . . . . . . . . . . . . . . . . . . . . . . . . 20

Customer Service access. . . . . . . . . . . . . . . . . . . 20

Deleting network settings . . . . . . . . . . . . . . . . . . . 20

Switch on or off the connection to the home

WLAN network (Wi-Fi). . . . . . . . . . . . . . . . . . . . . . 20

Information on data protection . . . . . . . . . . . . . . . 20

W Freezer compartment. . . . . . . . . . . . . . . . . . 21

Fully utilizing the freezer volume. . . . . . . . . . . . . . 21

Purchasing frozen food. . . . . . . . . . . . . . . . . . . . . 21

When loading products . . . . . . . . . . . . . . . . . . . . 21

Freezing fresh food. . . . . . . . . . . . . . . . . . . . . . . . 21

Thawing frozen food . . . . . . . . . . . . . . . . . . . . . . . 22

; Ice and water dispenser . . . . . . . . . . . . . . . 23

Before using the appliance for the first time. . . . . 23

Observing drinking water quality . . . . . . . . . . . . . 23

Information on operation of the ice maker . . . . . . 23

Dispensing ice and water . . . . . . . . . . . . . . . . . . . 23

= Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Freezer compartment . . . . . . . . . . . . . . . . . . . . . . 23

D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Care instructions for stainless steel

surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning the display . . . . . . . . . . . . . . . . . . . . . . . 24

Cleaning the equipment . . . . . . . . . . . . . . . . . . . . 24

> Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Normal noises . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Preventing noises . . . . . . . . . . . . . . . . . . . . . . . . . 25

en-us

3

9 Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3 Faults – what to do? . . . . . . . . . . . . . . . . . . . 26

Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

4 Customer service . . . . . . . . . . . . . . . . . . . . . 28

Appliance self-test . . . . . . . . . . . . . . . . . . . . . . . . .28

Repair order and advice on faults . . . . . . . . . . . . . 28

9 Important safety instructions

READ INSTRUCTIONS - DO NOT DISCARD!

en-us Important safety instructions

4

(Important safety instructions

Impor t ant saf et y i nst r uct i ons

READ INSTRUCTIONS - DO NOT DISCARD!

Definitions

9 WARNING

Non-observance of this warning could

result in death or serious injuries.

9 CAUTION

Non-observance of this warning could

result in slight or moderately serious

injuries.

NOTICE: Non-observance of this

information could damage the appliance.

Note: This indicates important information

and/or tips.

About these instructions

■ Read and follow the operating and

installation instructions. They contain

important information on how to install,

use and maintain the appliance.

■ The manufacturer is not liable if you

disregard the instructions and warnings

in the operating and installation

instructions.

■ Retain all documents for subsequent use

or for the next owner.

Introduction

■ This appliance complies with the relevant

safety regulations for electrical

appliances.

■ The refrigeration circuit has been

checked for leaks.

Restriction of user group

■ Avoid placing children and vulnerable

persons at risk.

■ This appliance may be used by children

and persons who have reduced physical,

sensory or mental abilities or inadequate

experience and/or knowledge, provided

they are supervised or have been

instructed on how to use the appliance

safely and have understood the resulting

dangers.

■ Children should be supervised to ensure

that they do not play with the appliance.

Risk of explosion

■ If the appliance's ventilation openings are

sealed, a leak in the refrigeration circuit

may result in a flammable mixture of gas

and air.

Keep ventilation openings in the

appliance enclosure or in the built-in

structure clear of obstruction.

■ Never use electric devices inside the

appliance (e.g. heaters or electric ice

makers).

■ Do not store products which contain

flammable propellants (e.g. spray cans)

or explosive substances in the appliance.

■ Only store high-proof alcohol tightly

closed and upright.

■ Do not use additional means to

accelerate the defrosting process other

than those recommended by the

manufacturer.

9 Important safety instructions

READ INSTRUCTIONS - DO NOT DISCARD!

Important safety instructions en-us

5

Risk of electric shock

Improper installations or repairs may put the

user at considerable risk.

■ When installing the appliance, make sure

that the power cord does not get jammed

or damaged.

■ In order to avoid danger, if the power

cord is damaged, disconnect the

appliance from the power source

immediately. Have the power cord

replaced by the manufacturer, customer

service or a similarly qualified person.

■ Do not use multiple outlets, extension

cords, or adapters.

■ Before servicing the appliance or

carrying out installation work, disconnect

the appliance from the power source or

switch off the fuse.

Before cleaning the appliance, press the

main On/Off switch to switch the

appliance off.

Glass shelves and other fittings can be

moved without any risk while the

appliance is switched on.

■ Never cut through or remove the power

cord's third conductor (grounding

conductor).

■ Never defrost or clean the appliance

using a steam cleaner. The steam may

penetrate electrical parts and cause a

short circuit.

■ The appliance, cord and accessories

should only be repaired or replaced by

the manufacturer or an authorized

service provider.

■ Only use original parts supplied by the

manufacturer.

These parts come with a warranty from

the manufacturer that they satisfy the

safety requirements.

Risk of cold burns

■ Never put frozen food straight from the

freezer compartment into your mouth.

■ Avoid prolonged skin contact with frozen

food, ice or any other surface inside the

freezer compartment.

Risk of injury

■ Containers with carbonated drinks may

burst.

■ Do not store containers which contain

carbonated drinks in the freezer

compartment.

Fire hazard/Danger due to

refrigerants

The tubes of the refrigeration circuit contain

a small quantity of an environmentally

friendly but flammable refrigerant (R600a).

It does not damage the ozone layer and

does not add to the greenhouse effect. If

the refrigerant escapes, it may injure your

eyes or ignite.

■ Do not damage the tubes.

If the tubes are damaged:

■ Keep naked flames and ignition sources

away from the appliance.

■ Ventilate the room.

■ Switch off the appliance and unplug the

mains plug.

■ Please contact customer service.

9 Important safety instructions

READ INSTRUCTIONS - DO NOT DISCARD!

en-us Important safety instructions

6

Risk of fire

Portable multi-outlet power strips and

portable power supplies may overheat,

causing a fire.

■ Never leave portable multi-outlet power

strips or portable power supplies behind

the appliance.

Risk of suffocation

■ If the appliance features a door lock:

keep the key out of the reach of children.

■ Keep children away from the packaging

and its parts.

Damage

To avoid damage:

■ Do not stand or lean on the base,

runners or doors.

■ Keep plastic parts and door seals free of

oil and grease.

■ Pull the power plug – not the power cord.

Weight

The appliance is very heavy. The appliance

should always be transported and set up by

at least 2 people.

~ "Installing the appliance" on page 7

State of California Proposition 65

Warnings

This product may contain a chemical known

to the State of California, which can cause

cancer or reproductive harm. Therefore, the

packaging of your product may bear the

following label as required by California:

Intended use en-us

7

8Intended use

Intended us e

Use this appliance

■ only for freezing food, making ice and dispensing

drinking water.

■ only in the home and in the home environment.

■ only according to these operating instructions.

This appliance is intended for use at an elevation of

no more than 2000 meters above sea level.

7Environmental protection

En v i r o n ment al pr ot ec t i on

Packaging

All materials are environmentally safe and

recyclable:

■ Dispose of packaging in an environmentally

responsible manner.

■ Please ask your dealer or inquire at your local

authority about current means of disposal.

Old appliances

Valuable raw materials can be reclaimed by

recycling old appliances.

9 WARNING

CHILDREN MAY BECOME LOCKED IN THE

APPLIANCE AND SUFFOCATE!

Before disposing of your old appliance:

■ Remove the door.

■ Leave shelves and bins in the appliance to

prevent children from climbing in.

■ Keep children away from the discarded

appliance.

9 CAUTION

REFRIGERANT AND HARMFUL GASES MAY

ESCAPE.

Do not damage the tubes of the refrigeration

circuit and insulation.

1. Pull out the power plug.

2. Cut through the power cord.

3. Have the appliance disposed of properly.

5 Installation and

connection

Inst all ati on and connect i on

Contents of package

After unpacking all parts, check for any damage

during transport.

If you have any complaints, please contact the

dealer from whom you purchased the appliance or

our customer service.

~ "Customer service" on page 28

The delivery consists of the following parts:

■ Built-in appliance

■ Equipment (depending on model)

■ Installation material

■ Instruction manual

■ Installation instructions

■ Customer service booklet

■ Warranty enclosure

■ Information on the energy consumption and

noises

Technical data

Refrigerant, cubic capacity and further technical

specifications can be found on the rating plate.

~ "Getting to know your appliance" on page 10

Installing the appliance

Installation location

The weight of the appliance may be up to 460 kg

depending on the model. The base must be

sufficiently stable and should not give. If necessary,

reinforce the floor.

Check built-in cut-out

The cut-out must fulfill these criteria:

■ Anti-tilt bracket must be fitted

■ Cut-out depth min. 24” (610 mm), for flush

installation 25” (635 mm)

■ rectangular

■ stable – the side panels and the top must be min.

5/8" (16 mm) thick and securely attached to the

floor or wall

■ Depth of shortest side panels min. 4” (100 mm)

Side-by-side installation

Observe the specifications in the installation

instructions for a side-by-side installation.

If a partition wall is required between the appliances

it must be at least 5/8" (16 mm) wide.

en-us Installation and connection

8

Saving energy

If you follow the instructions below, your appliance will use less power.

Note:

The arrangement of the equipment does not affect the energy consumption of the appliance.

--------

Installing the appliance

Keep the appliance out of direct sunlight. The appliance needs to cool less frequently at low ambient tempera-

tures and therefore consumes less power.

Install the appliance as far away as possible from heating elements,

cooker and other heat sources:

At least 1¼” (3 cm) from electric or gas cookers.

At least 11¾" (30 cm) from oil or solid-fuel cookers.

Select an installation location at a room temperature of approx. 68 °F

(20 °C).

Do not cover or block the ventilation openings. The appliance needs to cool less frequently if the warm air can

escape and therefore consumes less power.

Ventilate the room daily.

Using the appliance

Open the appliance door only briefly. The air in the appliance does not warm up so intensely. The appliance

needs to cool less frequently and therefore consumes less power.

Transport purchased food in a cool bag and place in the appliance

quickly.

Allow warm food and drink to cool down before placing in the appli-

ance.

Thaw frozen food in the refrigerator compartment to utilize the low

temperature of the frozen food.

Always leave a space between the food and the back panel. The air can circulate and the humidity will remain constant.The appli-

ance needs to cool less frequently and therefore consumes less

power.

Pack food airtight.

Do not cover or block the ventilation openings. The appliance consumes less power if the warm air can escape.

Vacuum the ventilation openings once a year.

Installation and connection en-us

9

Before using for the first time

1. Remove information material, adhesive tape and

protective foil.

2. Clean the appliance.

~ "Cleaning" on page 24

Water connection

9 CAUTION

■ Installation and connection of the appliance

must be carried out by authorized technicians

according to the installation instructions

supplied.

■ To avoid damage to the appliance and to

ensure its proper functioning, it should only be

connected to a drinking water system.

■ To avoid water damage, a shut-off valve must

be installed.

Water pressure of drinking water system

9 CAUTION

To avoid damage to the appliance, a pressure

relief valve must be installed between the

drinking water connection and the tubing,

should the water pressure exceed the

maximum value.

Note: If the water pressure is too low, this will impair

the relevant functions of the appliance.

■ Min. 0.2 Mpa (2 bar / 29 psi)

■ Max. 0.8 Mpa (8 bar / 116 psi)

Electrical connection

9 CAUTION

Do not connect the appliance to electronic

energy saver plugs.

Note: You can connect the appliance to mains-

controlled and sine-controlled inverters.

Mains-controlled inverters are used for photovoltaic

systems which are connected directly to the national

grid. Sine-controlled inverters must be used for

isolated applications. Isolated applications, e.g. on

ships or in mountain lodges, are not directly

connected to the national grid.

1. After installing the appliance, wait at least 1 hour

before connecting it to prevent damaging the

compressor.

2. Check that the outlet was installed according to

the regulations and complies with the

requirements.

Requirements for outlets

Maximum simultaneous load

3. Connect the appliance to an outlet near the

appliance.

The outlet must also be freely accessible

following installation of the appliance.

If free access is impossible, an all-pole isolating

switch must be integrated into the permanent

electrical installation according to the installation

regulations.

9 WARNING

RISK OF ELECTRIC SHOCK!

Never use multiple outlets, extension cords

or adapters.

The appliance must be grounded correctly.

Never cut through or remove the power

cord's third conductor (grounding

conductor).

9 WARNING

RISK OF ELECTRIC SHOCK!

If the power cord is too short, never use

multiple outlets or extension cords. Instead,

please contact customer service.

Outlet with 110 V ... 120 V

Protective conductor 60 Hz

Fuse 10 A ... 16 A

Appliance 6 A

en-us Getting to know your appliance

10

*Getting to know your

appliance

Get t i ng to know your appl i anc e

Appliance

Operating controls

Settings menu

Press " button to open the menu.

In the Settings menu you will find:

■ Appliance settings

■ Clean lock

■ Ice cube production

■ Water filter counter

■ Eco mode

■ Self-test

■ Sabbath mode (if activated)

~ "Operating the appliance" on page 14

( ... H Operating controls

P Main On/Off switch

X Door damper

` Ice maker

h Ice cube bin

)" Rating plate

)* Frozen food container

)2 Automatic door opening

): Ventilation opening

)B Water filter

)J ... 1* Dispenser

+

3

;





K



C



%

- 

( Touch fields

There are sensors under the touch fields.

Touching the symbol calls up the respective

function.

0 Freezer compartment temperature display

Indicates the set temperature in °F/°C.

8 +/- buttons

Used to change the temperature.

@ " button

Opens the Settings menu.

~ "Settings menu" on page 10

H Super Freeze button

Switches Super Freeze on or off.



6XSHU)UHH]H

C

²



6H W WLQJV



 



#



+

Getting to know your appliance en-us

11

Appliance settings menu

This is how to navigate to the Appliance settings

menu:

1. Press " button.

2. Use ( button to move to the Appliance settings

menu.

3. Open the menu using 8 button.

In the Appliance settings menu you will find the

following sub-menus and setting options:

■ Brightness

■ Key press sound

■ Key volume

■ Signal tone volume

■ Automatic clean lock

■ Automatic door opening

■ Water filter counter

■ Dispenser light

■ Motion sensor

■ Theater mode

■ Temperature unit

■ Language

■ Home network

■ Factory settings

■ Demo Mode

■ Sabbath mode

~ "Operating the appliance" on page 14

Ice and water dispenser

)J WATER button

Starts water dispensing.

)R CUBED button

Starts ice cube dispensing.

)Z CRUSHED button

Starts dispensing crushed ice.

)b LOCK button

Locks controls for dispenser panel lock

(child lock). To switch on or off, hold down

for 3 seconds.

)j Ice and water dispenser cover

1" Grate for drips

1* Drip tray

=





M

E- 5

en-us Getting to know your appliance

12

Equipment

Shelf

You can remove and adjust the shelf:

1. Lift shelf and remove.

2. When re-inserting, insert hooks on back of shelf

at same height to make it level.

Note: Insert shelf carefully to avoid scratching the

appliance.

Container

You can remove the container:

■ Press container to the rear,

■ lift the container at the rear and remove.

You can insert the bin:

■ Pull out the telescopic rails all the way.

■ Place the bin on the telescopic rails and push into

the appliance until it engages.

Ice pack

In the event of a power failure or a fault:

■ The ice pack delays the warming of stored frozen

food.

You can take out the ice pack to temporarily keep

food cool, e.g. in a cool bag.

Ice maker

9 CAUTION

DAMAGE TO THE APPLIANCE!

Never store bottles or food in the ice cube

container, even for short periods. This can

block and damage the ice maker.

Ice cube production starts as soon as the appliance

has reached the set temperature.

Notes

■ Ice cube production stops automatically when the

ice cube container is full.

■ When using the appliance for the first time,

discard ice cubes produced within the first

24 hours for hygiene reasons.

■ If you have stopped ice cube production for

several days, discard the first 30-40 ice cubes

produced for hygiene reasons.

Information about switching ice cube production on

and off

~ "Switching ice cube production on or off"

on page 15

Getting to know your appliance en-us

13

Water filter

Change the water filter after 6 months at the latest.

If the water or ice tastes stale, discard the rest of the

ice cubes and dispense several glasses of water

from the appliance. If the water still tastes stale,

change the water filter.

Note: If you use an external water filter system, you

can also operate the appliance without a water

filter.Replace the water filter with a bypass cartridge.

Switch off the water filter counter. There is no need

to change the bypass cartridge.

A new water filter or bypass cartridge can be

obtained from customer service or a specialist

dealer.

Exchange water filter or replace with bypass

cartridge

You can change the water filter, or replace it with a

bypass cartridge. The bypass cartridge can remain

in the appliance permanently: it does not need to be

changed.

Note: After installing a water filter or filter cartridge

with bypass, allow water to dispense for 5 minutes

for hygiene reasons and then discard. For hygiene

reasons, discard the ice cubes produced within the

first 24 hours.

1. Turn the cap of the built-in water filter counter-

clockwise.

2. Take the water filter out.

3. Remove the protective cap of the new water filter

or the new bypass cartridge.

4. Take off the cap of the used water filter and put it

on the new water filter or bypass cartridge.

5. Slide the new water filter or bypass cartridge to

the stop in the filter opening.

Note: The cap must be vertical here.

6. Turn the water filter or bypass cartridge clockwise

to the mark.

Note: If you do not turn the water filter or bypass

cartridge far enough, damage will be caused by

escaping water.

7. When installing a water filter: reset water filter

counter.

When installing a bypass cartridge: switch off

water filter counter.

8. Allow water to dispense for 5 minutes and

discard.

9. Drain the water out of the used water filter.

Note: You can dispose of the used water filter with

your household garbage.

en-us Operating the appliance

14

1Operating the appliance

Oper at i ng the appl i ance

Switching the appliance on

1. Press the main On/Off switch.

The appliance starts cooling and the light is

switched on when the door is open.

2. Set the required temperature.

~ "Setting the temperature" on page 14

Operating tips

■ When the appliance has been switched on, it may

take several hours until the set temperatures have

been reached. Do not put in any food until the

selected temperature has been reached.

■ The fully automatic NoFrost system ensures that

the freezer compartment remains frost-free.

Defrosting is not required.

■ The front sides of the housing are partly heated

slightly. This prevents condensation in the area

of the door seal.

■ If the freezer compartment door cannot be

immediately re-opened after it has been closed,

wait until the resulting low pressure has

equalized.

Switching off and disconnecting the

appliance

Switching off the appliance

■ Press the main On/Off switch.

The appliance is no longer cooling.

Disconnecting the appliance

9 CAUTION

Deterioration in water quality

The water supply must be turned off 3 hours

before disconnecting. This prevents mold

forming with any unused water.

If you do not use the appliance for a prolonged

period:

1. Turn off the water supply to the appliance and

wait 3 hours.

2. Remove groceries.

3. Press the main On/Off switch.

4. Pull out the mains plug or switch off the fuse.

The appliance is no longer cooling.

5. Empty the ice cube container and clean the

appliance.

~ "Cleaning" on page 24

6. Leave appliance open.

Setting the language

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Press ( button to move to the menu item

Language.

5. Press : button.

6. Use ( ) buttons to move to the required language.

7. Press 8 button.

The display restarts, and the start screen is

displayed.

Setting the temperature unit

You can choose between the unit °C and °F.

1 ° means 1 °F

1 °C means 1 °C

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Use ( button to move to the menu

item Temperature unit.

5. Press : button.

6. Use ( ) buttons to move to the required unit.

7. Press 8 button.

The unit will be changed.

8. Press ; button to exit the menu.

Setting the temperature

Recommended temperature

Freezer compartment

■ Keep pressing +/- button until the display

indicates the required temperature.

Super freezing

Super freezing cools the freezer compartment as

cold as possible.

Switch on super freezing, e.g.:

■ to quickly freeze food right through to the center

■ 4 ... 6 hours before freezing food weighing 2 kg

or more

Note: When super freezing is switched on, increased

operating noise may occur.

After approx. 2 ^ days the appliance switches to

normal operation.

Switching super freezing on or off

■ Press ]/ã button.

Freezer compartment: 0 °F (-18 °C)

Operating the appliance en-us

15

Clean lock

You can use this function to switch off the touch

function of the controls for 10 seconds. During this

time you can clean the display.

~ "Cleaning the display" on page 24

1. Press " button to open the Settings menu.

2. Press < button.

The cleaning display appears, and the countdown

starts.

Automatic clean lock

You can use this function to select whether the

automatic clean lock is switched on automatically

when the door is opened.

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Press ) button to move to the menu

item Automatic clean lock.

5. To change the setting, press : button.

Switching ice cube production on or off

9 CAUTION

Damage to the appliance!

Never store bottles or food in the ice cube

container, even for short periods. This can

block and damage the ice maker.

Ice cube production starts as soon as the appliance

has reached the set temperature.

Note: Ice cube production stops automatically when

the ice cube container is full.

Switching ice maker on or off

1. Press " button to open the Settings menu.

2. Use ) button to move to the menu item Ice cube

production.

3. Press </= button.

Reset water filter counter

After replacing the water filter, you have to reset the

water filter counter.

1. Press " button to open the Settings menu.

2. Use ) button to move to the menu item Reset

water filter counter.

3. Use 8 button to confirm, and confirm the query

again with 8 button.

Note: If you cancel the query or take longer than

10 seconds to make an input, the water filter counter

will not be reset.

Switching the water filter counter on and off

If you have replaced the water filter with a particle

filter, switch the water filter counter off. It is not

needed in this case as the particle filter does not

have to be replaced.

1. Press " button to open the Settings menu.

2. Use ( button to move to the Appliance settings

menu.

3. Press 8 button.

4. Press ) button to move to the menu item Water

filter counter.

5. To change the setting, press : button.

Eco mode

Eco mode switches the appliance to energy-saving

operation.

The appliance automatically sets the following

temperatures:

■ Freezer compartment: +3 °F (-16 °C)

Switching Eco mode on or off

1. Press " button to open the Settings menu.

2. Press ) button to move to the menu item Eco

mode.

3. Press </= button.

The temperature is changed and the display shows

the new temperature. When Eco mode is switched

off, the recommended temperature is set.

Note: You can also switch Eco mode on or off by

adjusting the temperature with +/- buttons.

Self-test

This function can be used to start fault analysis on

your appliance.

~ "Appliance self-test" on page 28

Setting the brightness of the control panel

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Press : button to open the menu

item Brightness.

5. Press ( ) buttons to set the required brightness.

6. Press 8 button.

The setting is saved.

7. Press ; button to exit the menu.

en-us Operating the appliance

16

Switching key press sound on or off

You can switch the sounds generated when pressing

keys off and back on again.

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button to open the menu item.

4. Press ) button to move to the menu item Key

press sound.

5. Press : button to open the menu item.

6. Use ( ) buttons to select the required setting.

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

Setting the key volume

You can adjust the volume level of the sounds

generated when pressing keys.

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button to open the menu item.

4. Use ) button to move to the menu item Key

volume.

5. Press : button to open the menu item.

6. Use ( ) buttons to select the required setting.

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

Setting the signal tone volume

You can adjust the volume level of the signal tones

generated e.g. with alarms.

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button to open the menu item.

4. Use ) button to move to the menu item Signal

tone volume.

5. Press : button to open the menu item.

6. Use ( ) buttons to select the required setting.

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

Automatic clean lock

You can use this function to select whether the

automatic clean lock is switched on automatically

when the door is opened.

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Press ) button to move to the menu

item Automatic clean lock.

5. To change the setting, press : button.

Automatic door opening

The automatic door opening function supports you in

opening the door.

As soon as you activate this function, automatic door

opening moves out and supports you in opening the

door.

9 CAUTION

Repeatedly closing the door too early will cause

automatic door opening to fail or wear out.

Do not close the door as long as automatic

door opening is still moved out.

If you have nevertheless closed the door, leave

it closed for 5 minutes. Automatic door opening

will re-adjust itself.

Open menu item Auto door opening:

1. Press " button to open the main menu.

2. Use ( button to move to the Appliance settings

menu.

3. Press 8 button to open the menu.

4. Press ) button to move the menu item Auto door

opening.

5. To change the setting, press : button.

Switching on Push-to-open system

In an installation situation without handles you can

select the Push-to-open system. Your appliance will

then open a crack if you press lightly on the door.

Note: Please note that automatic door opening is

disabled if Sabbath mode is activated.

1. Open menu item Auto door opening.

2. Select menu item Push-to-open system.

3. Press 8 button to open the menu item.

4. Select Opening force.Here you can select the

level of force required to activate automatic door

opening.

5. Select Opening duration.Here you can select

how long the door should remain open a crack

before it closes again automatically.

Note: If the door only remains open a crack, the

appliance checks once a second whether the door

is still ajar.After the selected opening duration

elapses, the appliance will close the door

automatically.

Switching on Pull-to-open system

In an installation situation with handles you can

select the Pull-to-open system. Your appliance will

support you in opening the door as soon as you pull

on the handle.

1. Open menu item Auto door opening.

2. Select menu item Pull-to-open system.

3. Press 8 button to open the menu item.

4. Select Opening force.Here you can select the

level of force required to activate automatic door

opening.

Switching off automatic door opening

1. Open menu item Auto door opening.

2. Select menu item Off.

Operating the appliance en-us

17

Switching the water filter counter on and

off

If you have replaced the water filter with a particle

filter, switch the water filter counter off. It is not

needed in this case as the particle filter does not

have to be replaced.

1. Press " button to open the Settings menu.

2. Use ( button to move to the Appliance settings

menu.

3. Press 8 button.

4. Press ) button to move to the menu item Water

filter counter.

5. To change the setting, press : button.

Dispenser light

Use this function to set how long the light will

illuminate the ice and water dispenser.

Adjusting dispenser light

1. Press " button to open the Settings menu.

2. Press < button to move to the menu item

Appliance settings.

3. Press 8 button to open the menu item.

4. Press > button to move to the menu item

Dispenser light.

5. Press : button to open the menu item.

6. Press > button to select the required duration.

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

Motion sensor

When the motion sensor is switched on, the ice and

water dispenser light automatically switches on as

soon as a glass is held underneath.

Switching motion sensor on or off

1. Press " button to open the Settings menu.

2. Press < button to move to the menu item

Appliance settings.

3. Press 8 button to open the menu item.

4. Press > button to move to the menu item Motion

sensor.

5. Press : button to open the menu item.

6. Use the > button to move to the menu item On or

Off.

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

Theater mode

If Theater mode is switched on, the light will slowly

become brighter when the appliance is opened, and

then slowly darker when it is closed.

Switching Theater mode on or off

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button to open the menu item.

4. Use ) button to move to the menu item Theater

mode.

5. Press : button to open the menu item.

6. Use ) button to move to the menu item On or Off.

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

Resetting to the factory settings

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Use ( button to move to the menu item Factory

settings.

5. Press : button.

A signal tone sounds, and a prompt to confirm

reset appears.

6. Press 8 button.

All settings are reset to the factory settings.

7. Press ; button to exit the menu.

Switching demo mode on or off

The cooling function of the appliance is switched off.

All other functions can be used.

Note: Do not store any food items in demo mode as

the appliance remains at room temperature.

1. Press " button to open the Settings menu.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Use ( button to move to the menu item Demo

mode.

5. Press : button.

6. Use ( ) buttons to select the setting On or Off

7. Press 8 button.

The setting is saved.

8. Press ; button to exit the menu.

en-us Alarm

18

Sabbath mode

All non-essential functions are switched off so you

can also use the appliance on the Sabbath.

The appliance switches off the following:

■ Ice maker

■ Audible signals

■ Interior light

■ Messages on the display

■ Background illumination of display is reduced

Switching Sabbath mode on or off

Displaying Sabbath mode in the Settings menu

To use Sabbath mode, you first have to display the

function in the Settings menu:

1. Press " button to open the Settings menu.

2. Use ( button to move to the Appliance settings

menu.

3. Press 8 button.

4. Use ( button to move to the menu item Sabbath

mode.Press : button.

5. Use ( button to move to the menu

item Available.Confirm by pressing 8 button.

6. Press ; button to exit the menu.

The function is added to the Settings menu.

Switching on Sabbath mode

1. Press " button to open the Settings menu.

2. Press › button to open the view Duration

Sabbath mode.

3. Select one of the presettings, or change the

duration with +/- buttons.

4. Press < button to start.

The appliance switches all listed functions off.

Switching Sabbath mode off

■ After the selected time elapses, the appliance

switches over to normal operation.

■ To end Sabbath mode before the selected time

elapses, press = button.

MAlarm

Al a r m

Door alarm

If the appliance door is open for a long time, the

door alarm switches on. A message appears on the

control panel.

Switching off the door alarm

■ Close the door.

Note: To mute the door alarm, you only have to

acknowledge the message on the control panel. If

the door remains opens a few more minutes, the

message will appear again.

Temperature alarm

If the freezer compartment becomes too warm, the

temperature alarm is switched on. A message

appears on the control panel. The message shows

the warmest temperature reached in the freezer

compartment.

9 CAUTION

DURING THE THAWING PROCESS, BACTERIA

MAY DEVELOP AND SPOIL THE FROZEN

ITEMS.

Do not refreeze partly or completely thawed

food.

Refreeze food only after cooking. No longer

store the frozen items for the maximum storage

period.

Note: The alarm may be actuated without risk to the

food in the following cases:

■ The appliance is put into service and does not yet

contain any food.

■ Large quantities of fresh food are placed in the

appliance.

■ The freezer compartment door has been open

too long.

Switching off the temperature alarm

1. Check that the cause of the temperature alarm

has been eliminated.

2. Press 8 button to acknowledge the message.

The message disappears. The control panel

again indicates the temperature selected.

From this time on the warmest temperature is

recalculated and saved.

Home Connect en-us

19

o Home Connect

Ho me Connect

This appliance is Wi-Fi-capable and can be

controlled remotely using a mobile device.

Note: Wi-Fi is a registered trade mark of the Wi-Fi

Alliance.

In the following cases, the appliance functions like a

refrigerator without a network connection and can

still be operated manually via the controls:

■ The appliance is not connected to a home

network.

■ The availability of the Home Connect function

depends on the availability of Home Connect

services in your country. Home Connect services

are not available in every country. You can find

more information on www.home-connect.com.

Note: Please observe the safety information in this

instruction manual. Ensure that this is also observed

if you operate the appliance via the Home Connect

app and are not at home when doing so.

~ "Important safety instructions" on page 4

Follow the instructions in the Home Connect app as

well.

Setting up a home network

Notes

■ Wait at least 2 minutes after switching on the

appliance before setting up Home Connect. Only

then is internal appliance initialization complete.

■ Take note of the Home Connect supplementary

sheet, which is supplied with the appliance or is

available for download at www.thermador.com

together with the instructions. Enter the E-number

of your appliance in the search field.

You can connect your appliance to the home WLAN

network (Wi-Fi) in 3 basic steps.

1. Install the app.

2. Connect your refrigerator to the home WLAN

network (Wi-Fi).

3. Connect the refrigerator to the Home Connect

app.

The first time you open the menu, you will be

automatically guided through initial setup. Follow the

instructions on the control panel. For further

information, please also see the following chapters.

The following sub-menus can be found in the Home

network menu:

■ Connection

■ Connect to app

■ Software update

■ Delete network settings

Open Home network menu

1. To open the Settings menu, press the " button.

2. Use ( button to move to the menu item Appliance

settings.

3. Press 8 button.

4. Press ( button to move to the menu item WiFi.

5. Press : button.

Note: The first time you open the menu, you will be

automatically guided through initial setup. Follow the

instructions on the control panel.

Setting up the connection to the home network

The first time you open the menu, you will be

automatically guided through initial setup. Follow the

instructions on the control panel.

1. Install the Home Connect app on your mobile

device.

2. Open the Home network menu on your

refrigerator.

3. Open the app on your mobile device.

4. Log in or register with the app if access is not yet

available.

5. Check the router of your home network to see if a

WPS function is available for automatic

connection.

6. If this function is available, start automatic

network connection with 8 button.

Follow the instructions on the control panel.

7. Start manual network connection if this function is

not available, if you're not sure whether the

function is available, or if automatic network

connection failed.

The refrigerator temporarily generates its own

network for connecting the mobile device.

8. Start manual network connection in the app of

your mobile device.

As soon as the refrigerator is connected to the

mobile device, a connection between the refrigerator

and your home network is established.

Note: If the connection cannot be established, check

whether there is sufficient reception.

~ "Verifying signal strength" on page 19

Verifying signal strength

The signal strength is displayed in the start window

of the Home network menu.The signal strength

should be at least 50 %. If the signal strength is too

weak, the connection may be interrupted.

Improving signal strength

■ Place the router closer to the refrigerator.

■ Check that screening walls do not interfere with

the connection.

■ Install a repeater to make the signal stronger.

Connecting the refrigerator to the

Home Connect app

Use this menu to connect your refrigerator to mobile

terminal devices.

1. Install the Home Connect app on your mobile

terminal device and log in or register.

2. Open the Home network menu on your

refrigerator.

3. Press ) button to move to the menu item Connect

to app.

4. Press : button to open the menu item.

en-us Home Connect

20

5. Confirm the prompt to display the refrigerator in

the app.

6. Open the app and wait until the refrigerator is

displayed.

Press Add to confirm the connection between the

app and the refrigerator.

If the refrigerator is not automatically displayed,

click on Add appliance in the app and follow the

instructions. As soon as your refrigerator is

displayed, add it with +.

7. Follow the instructions in the app until the

process is complete.

Installing updates for the Home

Connect software

The refrigerator checks at regular intervals whether

updates are available for the Home

Connect software.

The Info @ button is visible when an update is

available.

Installing the update:

1. Press @ button.

A note window with the necessary steps for

installing the new software appears.

2. Press 8 button to close the note.

3. Open the Home network menu on your

refrigerator.

4. Press ) button to move to the menu

item Software update.

5. Press : button to open the menu item.

Note: The : button is only visible if an update is

available.

The software is installed.

6. A note appears when installation is complete.

7. Press 8 button to close the note.

Customer Service access

If you contact Customer Service, they can access

your appliance and view its status after you have

given your consent. You need to have your

appliance connected to your home network for this.

Further information about Customer Service access

and its availability in your country is available under

www.home-connect.com in the Help & Support area.

1. Contact Customer Service.

~ "Customer service" on page 28

2. Confirm the start of Customer Service access in

the app.

During Customer Service access the symbol Ù

appears on the control panel.

3. As soon as Customer Service has obtained the

necessary data, they end access.

Note: You can interrupt remote diagnosis early by

switching off Customer Service access in the Home

Connect app.

Deleting network settings

If there is a problem when trying to establish a

connection, or if you would like to register the

appliance in a different home WLAN network (Wi-Fi),

the Home Connect settings can be reset.

1. Open the Home network menu on your

refrigerator.

2. Press ) button to move to the menu item Delete

network settings.

3. Press : button to open the menu item.

4. Confirm the prompt to delete the network

settings.

To then reconnect the appliance to the home WLAN

network (Wi-Fi), perform initial setup again.

~ "Setting up the connection to the home network"

on page 19

Switch on or off the connection to the

home WLAN network (Wi-Fi)

1. Open the WiFi menu on your refrigerator.

~ "Open Home network menu" on page 19

Note: The first time you open the menu, you will be

automatically guided through initial setup. Follow the

instructions on the control panel.

2. To open the menu item, press

Connection : button.

3. Use ( ) buttons to select the required setting.

4. To select the setting, press 8 button.

Note: If you switch off the Home Connect

connection, you will no longer be able to operate the

appliance with your mobile device.

Information on data protection

The first time your Home Connect appliance is

registered on a WLAN home network connected to

the Internet (Wi-Fi), your appliance will transmit the

following types of data to the Home Connect server

(initial registration):

■ Unique appliance identification (consisting of

appliance codes as well as the MAC address of

the installed Wi-Fi communication module).

■ Security certificate of the Wi-Fi communication

module (to ensure a secure data connection).

■ The current software and hardware version of

your domestic appliance.

■ Status of any previous resetting to factory

settings.

This initial registration prepares the

Home Connect functions for use and is only required

when you want to use these

Home Connect functions for the first time.

Note: Please note that the Home Connect functions

can be utilized only in conjunction with the

Home Connect app. Information on data protection

can be called up in the Home Connect app.

La page charge ...

Thermador T18ID905RP Mode d'emploi

Ce manuel convient également à

Thermador T18ID905RP Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents