Monogram ZIC30GNNII Guide d'installation

Marque: Monogram

Modèle: ZIC30GNNII

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATION

INSTRUCTIONS

30Ǝ Built-In

Bottom-Freezer, 2-Drawer

Refrigerator

ENGLISH/FRANÇAIS/ESPAÑOL

Monogram.com

31-1000169 Rev. 0

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

For Monogram local service in your area, call 800.444.1845 or visit monogram.com.

For Monogram service in Canada, call 888.880.3030

For Monogram Parts and Accessories, call 800.444.1845 or visit monogram.com.

For Monogram Parts and Accessories in Canada, call 888.880.3030 or visit monogram.ca.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from appliance. Failure to do so can result

in fire, explosion, or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance,

3 people are required for proper installation.

CAUTION

.HHSILQJHUVRXWRIWKH³SLQFKSRLQWƎDUHDVFOHDUDQFHVEHWZHHQWKHGRRUVDQGEHWZHHQWKH

doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the

fixed house wiring or circuit breaker for disconnecting the

appliance from the electrical supply after installation.

31-1000169 Rev. 0

Safety Information

Contents

Design Guide

Cabinet Enclosure Dimensions 4

Refrigerator Dimensions 5

The Installation Space 6

Grounding the Refrigerator 6

115° Door Swing 7

90° Door Swing 8

SS Panel Accessory & Dimensions 9

Ǝ&XVWRP3DQHO'LPHQVLRQV 

Installation Instructions

Tools, Hardware, Materials 11

Step 1. Remove Packaging 12

Step 2. Install Anti-tip Bracket 13

Step 3. Connect Water Line 13

Step 4. Connect Power 13

Step 5. Slide Unit into Enclosure 14

Step 6. Remove Toekick and Vent 14

Step 7. Level Refrigerator 14

Step 8. Install Toekick and Vent 15

Step 9. Reverse Door Swing 15

Step 10. Adjust Door Swing 16

Step 11. Install Door and Drawer Panels 18

Step12. Start Icemaker 18

Monogram Badge Placement 19

WARNING

EXPLOSION HAZARD Flammable Refrigerant

This appliance contains isobutane refrigerant,

R600a, a natural gas with high environmental

compatibility. However, it is also combustible.

Adhere to the warnings below to reduce the risk of

injury or property damage.

1) When handling, installing and operating the appliance,

care should be taken to avoid damage to the

refrigerant tubing.

2) Service shall only be performed by authorized service

personnel. Use only manufacturer-authorized service

SDUWVƎ

3) Dispose of refrigerator in accordance with Federal

and Local Regulations. Flammable refrigerant and

insulation material used require special disposal

procedures. Contact your local authorities for the

environmentally safe disposal of your refrigerator.

4) Keep ventilation openings in the appliance enclosures

or in the built-in structure clear of obstruction.

5) Do not use mechanical devices or other means to

accelerate the defrosting process.

6) Do not damage refrigerant circuit.

7) Do not use electrical appliances inside the food

storage compartment of the appliance.

31-1000169 Rev. 0

Design Guide

Cabinet Enclosure Dimensions For Fully Integrated Instructions

Height options

80" or *84"

30" Finished Width

25" min. depth

7KHFXWRXWGHSWKPXVWEHƎIRU

flush installations.

• The front face of the refrigerator

ILWVIOXVKZLWKƎGHSWKDGMDFHQW

cabinets.

• The refrigerator can fit into a

ƎPLQLPXP

ƎPD[LPXPKLJKHQFORVXUH

Although the refrigerator itself can

RQO\EHUDLVHGWRƎ

• The fresh food door panel can be

FRQVWUXFWHGWRILOODGGLWLRQDOKHLJKW

see page 11.

'HVLJQ7LS:HUHFRPPHQGILQLVKLQJWKHLQVLGHVXUIDFHRIWKHHQFORVXUHDPLQRIƎIURPWKHIURQWIDFH

'HVLJQ7LS,IXVLQJƎHQFORVXUHFRQVLGHUDGGLQJDILQLVKHGYDOHQFHDERYHWKHUHIULJHUDWRUFDVH

34 3/8"

Design Tip: It is possible to align your refrigerator drawer with adjacent cabinetry for a completely

integrated look.

31-1000169 Rev. 0

Design Guide

Height adjustable

from

79-3/8” to 80-3/8” *

23 3/4"

29 3/4"

1 1/4"

3/4"

1/8"

Case

Door

Panel

Clearance

Front with Panels Side with Panels

5HIULJHUDWRU'LPHQVLRQVZLWKƎ3DQHOV

Top with Panels

Install Clearances

Top

ƎPP

Each Side

ƎPP

Rear

ƎPP

7KH5HIULJHUDWRUFDQEHDGMXVWHGWRILWLQWRDFDELQHWVSDFHWKDWLVƎWRƎZLWKWKH

appropriate door panel kit.

(Case and Door only)

31-1000169 Rev. 0

Design Guide

THE INSTALLATION SPACE

Water and Electrical Locations

Electrical and water supply should be located in shaded area only as

shown.

WARNING

Connect to potable water supply only.

PREPARING INSTALL WATER LINE

• A cold water supply is required for automatic icemaker operation. The

water pressure must be between 40 and 120 p.s.i. (275-827 kPa).

5RXWHƎ2'FRSSHURU6PDUW&RQQHFW

™

plastic tubing between the

house cold water line and the water connection location.

• Tubing should be long enough to extend to the front of the encloasure.

• Water line can enter an opening through the floor or back wall.

• Install a shut-off valve between the icemaker water valve and cold water

supply in the home.

NOTE:

• It is recommended that the water shut-off valve be placed in a location

that is easily accessible. We do not advise placing it behind the unit

because of access difficulties. If it is necessary to install the valve behind

the unit, it must be located in the shaded area.

• Saddle type shut-off valves are included in many water supply kits, but

are not recommended for this application.

• The only GEA-approved plastic tubing is supplied in the SmartConnect

™

Refrigerator Tubing kits. Do not use any

other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or

rupture with age and cause water damage to your home. SmartConnect

™

Refrigerator Tubing Kits are available in

the following lengths:

6’ (1.8 m) WX08X10006, 15’ (4.6 m) WX08X10015 & 25’ (7.6 m) WX08X10025

• Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use

is not permitted in Massachusetts. Consult with your licensed plumber.

Electrical Specifications

• A 115-volt, 60-Hz., 15- or 20-amp power supply is required. An individual properly grounded branch circuit or circuit

breaker is recommended.

• Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on

rear wall as shown.

NOTE: GFI (ground fault interrupter) is not recommended.

GROUNDING THE REFRIGERATOR

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

three-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT

OR REMOVE THE THIRD

(GROUND) PRONG FROM

THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT THE

REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

6”

80”

77”

nti-Tip location. Do

not obstruct this area.

Water and Electrical

Tube Outlet

Front view

Install Space

WARNING

Electrical Shock

Hazard.

Failure to follow these instructions can

result in death, fire, or electrical shock.

31-1000169 Rev. 0

Design Guide

1-1/2"

1-1/4"

3/4"

1-1/2"

2-1/16"

1-1/4"

1-3/8"

3/4"

1/8"

Allow 17" minimum clearance

for a full 115° door swing.

Refrigerator

Stainless Steel or Custom Panels

Top View

115° DOOR SWING

(factory setting)

Product Clearances

These refrigerators are equipped with a 2-position door stop. The factory-set 115° door swing can

be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.

For 90° Door swing see page 8.

Not to scale

31-1000169 Rev. 0

Design Guide

For a 90º door swing

allow 4" min.

clearance to a wall,

for stainless steel

models.

1-1/2"

2-1/4"

1-1/4"

3/4"

1-1/2"

1-1/4"

1-3/16"

3/4"

Refrigerator

Stainless Steel or Custom Panels

Top View

90° DOOR SWING

(optional setting)

Not to scale

31-1000169 Rev. 0

Design Guide

Optional Accessory Kits #:

• Side-by-Side Installation Kit – ZUG30

• Contemporary Handle Kit: ZKGB3H3CNSS

• Pro Handle Kit: ZKGB3H3PNSS

SS PANEL ACCESSORY & DIMENSIONS

Ǝ7KLFN)UDPHIRU*ODVV'RRU2SWLRQV

)RUƎ+LJK,QVWDOODWLRQ

• LH Integrated – Model ZKGSN809NLH

• RH Integrated – Model ZKGSN804NRH

)RUƎ+LJK,QVWDOODWLRQ (The door panel is not

UHYHUVLEOHIRUWKHƎ,QVWDOODWLRQV$OHIWRUULJKWKDQG

door panel accessory must be purchased.)

• LH Integrated – Model ZKGSN849NLH

• RH Integrated – Model ZKGSN844NRH

NOTE: Each option also contains matching freezer and

Convertible drawer panels, handles and toekick.

Ǝ7KLFN6ROLG'RRU3DQHO2SWLRQV

)RUƎ+LJK,QVWDOODWLRQ

• LH Integrated – Model ZKSSN809NLH

• RH Integrated – Model ZKSSN804NRH

)RUƎ+LJK,QVWDOODWLRQ (The door panel is not

UHYHUVLEOHIRUWKHƎ,QVWDOODWLRQV$OHIWRUULJKWKDQG

door panel accessory must be purchased.)

• LH Integrated – Model ZKSSN849NLH

• RH Integrated – Model ZKSSN844NRH

NOTE: Each kit also contains matching freezer and

customizable drawer panels, handles and toekick.

7KHUHPXVWEHDPLQLPXPƎJDSEHWZHHQSDQHOV

and surrounding cabinetry.

29-3/4"

7-9/16"

22-3/4"

1/8" Min.*

Fresh

Food

Ice Drawer

Cabinets

Freezer/

Convertible

Drawer

45-3/8" for 80" Installation

49-3/8" for 84" Installation

29-3/4"

23"

Glass Panel

for Fresh Food

45-3/8"

49-3/8"

3-3/8"

80"

Install.

10"

84"

Install.

31-1000169 Rev. 0

Design Guide

3/4Ǝ&867203$1(/',0(16,216Ǝ+LJK)XOO\,QWHJUDWHG,QVWDOODWLRQ

Ǝ&867203$1(/',0(16,216Ǝ+LJK)XOO\,QWHJUDWHG,QVWDOODWLRQ

If you choose to install custom panels, they must be cut

to the dimensions shown. The panels will attach to the

door and drawers using a hook and bracket system.

EXTREMELY IMPORTANT: Custom wood panels

PXVWEHDWOHDVWƎWKLFNZKHUHKRRNVDQGEUDFNHW

hardware are attached. Refer to Templates for hook

and bracket location.

NOTE:7KLVSURGXFWLVGHVLJQHGWRKDQGOHƎSDQHOV

that are made of wood.

Ǝ[ƎLVWKHPD[LPXPRSHQLQJIRUDJODVV

window. The opening may be smaller if desired.

If you choose to install custom panels, they must be cut

to the dimensions shown. The panels will attach to the

door and drawers using a hook and bracket system.

EXTREMELY IMPORTANT: Custom wood panels

PXVWEHDWOHDVWƎWKLFNZKHUHKRRNVDQGEUDFNHW

hardware are attached. Refer to Templates for hook

and bracket location.

NOTE:7KLVSURGXFWLVGHVLJQHGWRKDQGOHƎSDQHOV

that are made of wood.

Ǝ[ƎLVWKHPD[LPXPRSHQLQJIRUDJODVV

window. The opening may be smaller if desired.

IMPORTANT NOTE: Maximum panel weight:

A Fresh Food Door Panel: 33 lbs.

B Freezer Drawer Panel: 9 lbs.

C Convertible Drawer Panel: 19 lbs.

IMPORTANT NOTE: Maximum panel weight:

A Fresh Food Door Panel: 33 lbs.

B Freezer Drawer Panel: 9 lbs.

C Convertible Drawer Panel: 19 lbs.

45-3/8”

33-3/8”

45-3/8

29-3/4"

7-9/16

22-3/4

PANELS FOR SOLID DOOR

AND DRAWERS

PANELS FOR SOLID DOOR

AND DRAWERS

PANELS FOR

GLASS DOOR

PANELS FOR

GLASS DOOR

6W\OHVPXVWEHDPLQƎWRFRYHU

aluminum door frame.

6W\OHVPXVWEHDPLQƎWRFRYHU

aluminum door frame.

Design Tip: Some amount of each panel will be visible on the interior side

of the unit. It is recommended that both sides of each panel be finished.

Design Tip: If using custom panels, a custom toe kick should

be considered. The Bottom of case is white.

Design Tip: Some amount of each panel will

be visible on the interior side of the unit. It is

recommended that both sides of each panel

be finished.

Design Tip: If using custom panels, a custom

toe kick should be considered. The Bottom of

case is white.

49-3/8”

33-3/8”

49-3/8"

29-3/4"

22-3/4"

7-9/16"

31-1000169 Rev. 0

Installation Instructions

TOOLS REQUIRED

Ǝ$OOHQZUHQFK

• Utility knife

• Stepladder

• Bucket

• Level

• Appliance hand truck

• Tubing cutter

ƎRSHQHQGZUHQFK

ƎRSHQHQGZUHQFK

• #2 Phillips screwdriver

• Drill and bit set

ƎVRFNHW

• Safety glasses

• Pliers

ƎUDWFKHW

• Torx T-20, T-30 wrench

HARDWARE SUPPLIED

• Anti-tip bracket & screws

• Panel installation kit

• Door panel templates- Pub # 31-1000149, 31-1000150,

31-1000151, 31-1000152

• Water filter - Part # GSWF

• Drywall Anchors and screws

MATERIALS REQUIRED

ƎFRSSHUZDWHUOLQHWXELQJRU6PDUW&RQQHFW

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for fresh food door, freezer drawer and

Convertible drawer

• Velcro w/adhesive if using custom toekick.

FLOORING

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should be

strong enough to support a fully loaded refrigerator, or

approximately 1,200 lbs.

NOTE: Protect the finish of the flooring. Cut a large sec-

tion of the cardboard carton and place under the refriger-

ator where you are working.

REFRIGERATOR/FREEZER LOCATION

Ŷ Do not install the refrigerator/freezer where the

temperature will go below 55°F (13°C). It will not run

often enough to maintain proper temperatures.

Ŷ Do not install the refrigerator/freezer where

temperatures will go above 100°F (37°C). It will not

perform properly.

Ŷ Do not install the refrigerator/freezer in a location

exposed to water (rain, etc.) or direct sunlight.

Ŷ Install it on a floor strong enough to support it fully

loaded.

31-1000169 Rev. 0

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

This appliance is top heavy. Use extreme caution

with moving to prevent tipping over which could

result in death or serious injury.

Ŷ Cut bands and tape on the top and bottom

of packaging with a utility knife.

Ŷ Unfold the cardboard seams and remove the top

of the packaging.

Ŷ Slide the remainder of the box off of the appliance. You

can use a box cutter to cut the remaining cardboard

being VERY CAREFUL not to scratch

the appliance.

Ŷ Remove the Styrofoam supports from around the unit.

Ŷ DO NOT remove door band or lower EPS banded part

until unit is ready to go into enclosure.

Ŷ Cut EPS skid at the sides near the front from the back

of the unit.

Ŷ Push unit forward & remove rear portion of the EPS

skid.

Ŷ Carefully lower rear onto the floor.

Ŷ Lean unit back slightly & remove front portion of the

EPS skid.

Ŷ Discard all unused packaging materials appropriately.

Ŷ The unit can now be moved using an appliance hand

truck or rolled on a properly protected floor by 2

people.

Ŷ Leave any protective film on the refrigerator until

installation is complete.

Installation Instructions

31-1000169 Rev. 0

Installation Instructions

67(3,167$//$17,7,3

BRACKET

Ŷ Inside Top Face of bracket should be installed at

Ǝ³6ORWƎLQEUDFNHWVKRXOGWREHSODFHGLQFHQWHURI

LQVWDOO6SDFH7\SLFDOO\Ǝ

Ŷ Mark (within slots, placement) stud and anchor

positions on brackets.

Ŷ Secure bracket using combination of studs &

anchors.

Ŷ At least 1 stud must be engaged. However, please

engage as many studs as possible within the

enclosure. A minimum of three fasteners should be

used for proper installation.

STEP 3 CONNECT WATER LINE

WARNING

Connect to potable water supply

only.

Ŷ Position appliance in front of enclosure.

Ŷ Locate and bring tubing to the front of the cabinet.

Ŷ Turn the water on to flush debris from line. Run about

DTXDUWRIZDWHUWKURXJKWXELQJLQWRDEXFNHWWKHQ

shut off water.

If needed cut the tubing to the proper length so it can

be attached to the water valve.

Copper Tubing:

Ŷ 6OLSDƎQXWDQGIHUUXOHRYHUERWKHQGVRIWKH

copper tubing. Insert tube into the union fitting on the

unit and tighten nut to union.

Ŷ Turn on the water to check for leaks.

SmartConnect™ Tubing:

Ŷ Insert the end of the tubing into the refrigerator

connection. Tighten the compression nut until it is just

hand-tight.

Ŷ Tighten one additional turn with a wrench.

Overtightening can cause leaks!

Ŷ Turn on the water to check for leaks.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any

doors open, and must be secured to prevent tipping

forward which could result in death or serious injury.

Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

Water

Line Hole

STEP 4 CONNECT POWER

Ŷ Plug the power cord into the socket.

Ŷ Check to make sure power to refrigerator is on by

opening the ice drawer (FF door will be banded shut)

to see if interior lights are on.

Ŷ The temperature controls are preset at 37°F for the

fresh food section and 0°F in both the freezer drawer

and customizable drawer.

Ŷ Allow 24 hours to stabilize before making

adjustments.

80”

Slot

31-1000169 Rev. 0

STEP 5 SLIDE UNIT INTO

ENCLOSURE

Roll the unit into the enclosure, being careful not to

pinch the water line or power cord.

Ŷ$ORQJIODWEDURU\DUGVWLFNPD\EHQHHGHGWRJXLGH

the front edge of the anti-tip bracket over the unit.

ŶIf space allows, you may also bend the front edge of

the bracket upward slightly, allowing it to clear the

back of the unit.

ŶRemove Top-Center trim cover from unit.

ŶSecure the unit to the Anti-tip bracket using both

machine screws & washers to engage the threaded

inserts in the anti-tip bracket.

ŶHand start the screws until unit is in desired location

within the install space.

ŶFinalize unit install by tighening the screws fully.

ŶReinstall Trim cover.

STEP 7 LEVEL REFRIGERATOR

All models have 4-point leveling. The front is supported

E\OHYHOLQJOHJVWKHUHDULVVXSSRUWHGE\DGMXVWDEOH

wheels. Both are accessible from the front of the

refrigerator.

Ŷ7ROHYHOWKHEDFNRIWKHUHIULJHUDWRUWXUQWKHƎ

hex nut located above the front wheels. Turn

counter clockwise to raise or clockwise to lower the

refrigerator.

Ŷ)RUIURQWOHYHOLQJXVHDƎRSHQHQGZUHQFK

ŶAdjust height of refrigerator to match installation

cutout opening. The refrigerator should be level and

plumb with cabinetry.

NOTICE: The rear leveling wheels and front leveling

OHJVDUHOLPLWHGWRDPD[LPXPKHLJKWDGMXVWPHQWRIƎ

,IWKHLQVWDOODWLRQUHTXLUHVPRUHWKDQƎKHLJKWWKH

installer should elevate the refrigerator on a sheet of

plywood or runners. Cabinetry trim could also be added

across the top of the opening to shorten the opening.

,I\RXDWWHPSWWRUDLVHWKHUHIULJHUDWRUPRUHWKDQƎ\RX

will damage the front leveling legs and the rear leveling

wheels.

Installation Instructions

STEP 6 REMOVE TOEKICK AND

VENT

The toekick must be removed to access

the leveling leg system.

ŶRemove band around EPS block in front of toekick.

ŶRemove and dispose of EPS block.

ŶRemove the solid portion of the toekick by pulling

forward.

Ŷ Place the toekick, vent and screws out of the way so

you will have them for reinstallation.

Vent

Screw

Toekick

Vent

Screws

(behind

toekick)

Screw

Leveling Leg

Hex Nut Adjusts

Rear Wheels

31-1000169 Rev. 0

Installation Instructions

STEP 8 INSTALL TOEKICK AND

VENT

ŶLocate the toekick, vent and screws (removed

earlier).

ŶA custom toekick can be installed to match or

complement the surrounding cabinetry. Use the

supplied toekick as a template.

ŶReinstall the vent using the screws removed earlier.

ŶReinstall the toekick .

Supplied Toekick

Vent Holes

STEP 9 REVERSE DOOR SWING

(if needed)

Skip this step if door swing is satisfactory.

WARNING

Follow all steps when reversing

the door swing. Failure to follow these instructions,

leaving off parts, or overtightening screws, can

lead to the door falling off and result in injury and

property damage.

1. Open the fresh food door.

WARNING

Door Hinge Pinch

Point Hazard

This next step is important for safe handling of an

unloaded hinge. Do not skip step 2.

2. Release the hinge springs by using a Torx T-20

wrench to loosen the Torx screw from | to 0 on both

hinges. Close the door.

Top Hinge Bottom Hinge

Slots for

Tabs

Screws

Control Panel

STEP 9 REVERSE DOOR SWING

(if needed) (cont.)

8VLQJDƎ$OOHQZUHQFKUHPRYHWKHVFUHZV

per hinge that secure the door to the refrigerator.

Have someone hold the door while removing these

screws to keep the door from falling.

2SHQWKHKLQJHV8VLQJDƎ$OOHQZUHQFK

remove the 2 screws per hinge that secure the hinge

to the refrigerator cabinet.

5. Remove the trim and hinge pocket from the top of

the refrigerator and install on the opposite sides.

6. Remove the trim and hinge pocket from the bottom

of the fresh food compartment. Remove the control

panel and gently place in the FZ drawer.

7. Reinstall the control panel.

8. The hinges will be reinstalled in opposite corners.

The hinge from the top will be turned over

and installed at the bottom of the fresh food

compartment. The hinge from the bottom will be

turned over and installed at the top of the fresh food

compartment.

9. Install the screws on the fresh food compartment

cabinet in all 4 places. Screw them in about halfway.

Screws

31-1000169 Rev. 0

Installation Instructions

Screws

STEP 9 REVERSE DOOR SWING

(cont).

10. To install the top hinge, turn the hinge in the proper

direction—the section of the bracket that will be

attached to the door should be at the bottom of the

hinge. Slide the hinge over the screws and seat the

tabs into the hinge pocket. Tighten the screws.

11. To install the bottom hinge, turn the hinge in the

proper direction—the section of the bracket that will

attach to the door should be at the top of the hinge.

Slide the hinge over the screws and seat the tabs

into the hinge pocket. Tighten the screws. Close the

hinge.

12. Remove the hinge brackets from the door and rein-

stall them on the opposite end, top and bottom.

13. With another person holding the door in place, align

the holes in the door hinge bracket with the holes in

the hinge. Install the screws to the top hinge first.

14. Install screws on the bottom hinge next.

15. Using a Torx T-20

wrench, tighten the

tension on the hinge

springs by turning

the screws from 0

to |.

STEP 10 ADJUST DOOR SWING

(if needed)

NOTE: This refrigerator has a 2-position door stop.

When space does not allow the door to swing to 115°,

you may limit the door swing to a 90°

Skip this step if door opening is satisfactory for your

installation situation.

Ŷ2SHQWKHIUHVKIRRGGRRUWRDFFHVVWKHWRSDQG

bottom hinges.

Ŷ/RRVHQWKHERWWRPKLQJHVFUHZVWKDWDWWDFKHGWRWKH

unit

Ŷ3XOOKLQJHIRUZDUGVOLJKWO\LQVHUWKLQJHSLQLQWRWKH

hole nearest the unit.

Ŷ<RXPD\QHHGWRXVHDVPDOOKDPPHUWRIXOO\VHDW

them in place.

Ŷ5HWLJKWHQKLQJHVFUHZV

ŶRepeat for top hinge.

Door

Screws

Use Torx

T-20 Wrench

Install 1 pin,

per hinge for 90°

door stop.

Hinge screws

31-1000169 Rev. 0

Installation Instructions

STEP 11 INSTALL DOOR AND DRAWER PANELS

1. Remove all door and drawer panel hardware and trim

from the refrigerator.

2. Attach A1 - F1 brackets to the door panels in the

locations identified below. Custom panels must have

pre-drilled holes as shown in Door Panel Templates:

31-1000149, 31-1000150, 31-1000151, 31-1000152.

If you purchased an SS Panel Accessory, use the

Phillips machine screws to attach the brackets to the

SS door panels. For custom panels, use an appropriate

wood screw.

3. If you had custom handles made and they are not

currently attached to your panels, do so now.

4. Remove the screw caps from the adjustment pins on

the doors.

5. Open the fresh food door to attach the fresh food

panel.

6. Rest the fresh food panel on the fresh food door by

aligning the hooks on the panel brackets with the

adjustment pins on the door.

7. Fasten the panel to the fresh food door in four locations

using the hardware shown below. Do not tighten the

screws. Screws will be tightened after panel alignment.

8. Shift the panel side to side to ensure even gaps with

the adjacent cabinetry on both sides.

9. Use an allen wrench

to adjust the fresh

food door panel depth

and height to align

with the adjacent

cabinetry. There must

be a minimum 1/8” gap

between the panel and

the adjacent cabinetry.

Item Quantity

Panel Brackets 12

Phillips Machine

Screws (for use

with SS Panel

Accessory)

Allen Hex Socket

Head Screws

Washers 12

Door Trim 6

Trim Caps 12

Allen Wrench 2

Refrigerator

Panel

Customizable

Panel

Back View of Panels

Freezer

Panel

Do not tighten the screws, you will

do that after assembly process

and left to right alignment.

Align at top

and bottom

Screw and

Washer

Depth Adjustment

Vertical

Adjustment

Tighten one screw per bracket.

The other screws will be

tightened at the end of the

alignment process.

31-1000169 Rev. 0

Installation Instructions

STEP 12 START ICEMAKER

Ŷ Press the zone indicator on the control pad twice

to select the freezer drawer. Press the ICE icon on

the right side of the control. A line will appear under

ICE to show that the icemaker is ON.

Ŷ Be sure nothing interferes with the sweep of the

feeler arm.

Ŷ Discard the first full bucket of ice cubes.

Ŷ To turn the icemaker off, press the ICE icon. The

word OFF appears below ICE to show that the

icemaker is OFF.

STEP 11 INSTALL DOOR AND

DRAWER PANELS

(cont.)

10. Repeat steps 5-9 for the freezer drawer.

11. Repeat steps 5-9 for the customizable drawer.

12. Tighten all screws once you are satisfied with the

panel alignment.

13. Slide on trim to hide the panel adjustment hardware.

14. Add trim caps to cover the ends of the trim.

Trim

Align trim with bracket

31-1000169 Rev. 0

Installation Instructions

MONOGRAM BADGE PLACEMENT

TOP OF REFRIGERATOR

SIDE OF REFRIGERATOR

0.675"

5.5"

NOTE: While performing installations described in this

book, safety glasses or goggles should be worn.

NOTE: Product improvement is a continuing endeavor

at Monogram. Therefore, materials, appearance and

specifications are subject to change without notice.

31-1000169 Rev. 0

03-19 GEA

La page charge ...

Monogram ZIC30GNNII Guide d'installation

Marque: Monogram

Modèle: ZIC30GNNII

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Monogram ZIC30GNNII Installation guide
español: Monogram ZIC30GNNII Guía de instalación

Monogram ZIC30GNNII Guide d'installation

Ce manuel convient également à

Monogram ZIC30GNNII Guide d'installation

dans d''autres langues

Documents connexes

Autres documents