GE PDT845SMJES Guide d'installation

Marque: GE

Modèle: PDT845SMJES

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com.

In Canada, please call 1.800.561.3344 or visit www.geappliances.ca

READ CAREFULLY

KEEP THESE INSTRUCTIONS

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS shown

throughout these instructions. While performing installations

described in this booklet, gloves, safety glasses or goggles

should be worn.

IMPORTANT – Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions for the

consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with your

Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GE Appliance Warranty. See warranty information.

• Completion Time – 1 to 3 Hours. New installations require

more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to

allow for future removal from the enclosure if service is required.

Care should be exercised when the appliance is installed or removed,

to reduce the likelihood of damage to the power supply cord.

If you received a damaged dishwasher, you should immediately

contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for available

custom panel kits.

Your dishwasher is a water heating appliance.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

31-31560 02-16 GE

Printed in the United States

• 7RUHGXFHWKHULVNRIHOHFWULFVKRFN¿UHRULQMXU\WR

persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

• FOR PERSONAL SAFETY: Remove house fuse or open

circuit breaker before beginning installation. Do not use an

extension cord or adapter plug with this appliance.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check with

DTXDOL¿HGHOHFWULFLDQRUVHUYLFHUHSUHVHQWDWLYHLI\RXDUH

in doubt that the appliance is properly grounded.

• If house wiring is not 2-wire with ground, a ground

must be provided by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

Do not remove wood base until you are ready to install the

dishwasher. The dishwasher will tip over when the door is

opened if base is removed.

CHECK THE FOLLOWING

 Tub trim does not interfere with the door

 Dishwasher is square and level at both the top and bottom

of the cabinet opening, with no twisting or distortion of the

tub or door

 $OOOHJVRIWKHGLVKZDVKHUDUH¿UPO\LQFRQWDFWZLWKWKH

ÀRRU

 Drain hose is not pinched between the dishwasher and

DGMDFHQWFDELQHWVRUZDOOV

 7XEWULPLVIXOO\VHDWHGRQWKHWXEÀDQJH

CAUTION

WARNING

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4" and 5/16" nutdriver

• $GMXVWDEOHZUHQFK

• Level

• Carpenter's square

• Measuring tape

• Safety glasses

• Flashlight

• %XFNHWWRFDWFKZDWHUZKHQÀXVKLQJWKHOLQH

• 15/16" socket (optional for skid removal)

• Gloves

• Pliers

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

Hot Water Line

Hole Saw Set

Level

Strain Relief

Drain Hose

Hose Clamp

#8 Hex-Head Mounting

Bracket Screws

1/4" and 5/16"

Nutdriver

15/16" Socket

Bucket

Tubing Cutter

Drill and Bits

Flashlight

Gloves

Phillips-Head

Screwdriver

Carpenter's

Square

Adjustable

Wrench

Safety Glasses

Pliers

Installation Preparation

Drain Hose Hanger

Measuring Tape

PARTS SUPPLIED

IN INSTALLATION PACKAGE:

• Junction box cover and #10 hex-head screw

• Hose clamp

• Drain hose (approximately 58" long)

• Drain hose hanger

• 2 #8-18 hex head screws to secure brackets to washer

tub frame

• 1 top trim piece (on some models)

• 2 side trim pieces

• 2 mounting brackets for wood countertops or side

cabinets

• 2 #8-18 x 5/8" Phillips special head screws, to secure

dishwasher to underside of countertop or to side

cabinets

• Literature, samples and/or coupons

MATERIALS YOU WILL NEED:

• 90° elbow (3/4"hose internal thread on one end,

opposite end sized to fit water supply)

• UL-listed wire nuts (3)

• Masking Tape

Materials Needed for New Installations:

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• Electrical cable or Power Cord Kit WX09X70910 (5.4 Ft)

or WX09X70911 (7.9 ft) depending on your installation.

• Screw-type hose clamps

• Strain relief for electrical connection

• Hand shut-off valve (recommended)

• Hot Water Line–3/8" minimum, copper tubing

(including ferrule, compression nut) or GE Part #

WX28X326, flexible braided hose.

• WD24X10065 drain hose (12' long), if needed

Junction

Box Cover

#10

Hex-Head

Junction

Box Screw

1/2" long

Optional

12' Drain Hose

WD24X10065

Hose Clamps

Waste Tee

Electrical Cable

(or Power Cord, if applicable)

Wire Nuts (3)

Mounting

Brackets

#8 Phillips

Special

Head Screws

5/8" long

Literature

90°Elbow

Top Trim Piece

(on some models)

Side Trim Pieces

Coupler for

optional drain

hose

Hand

6KXW2ȹ

Valve

Air Gap

Plug Buttons

Masking Tape

(if applicable)

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes and ordi-

nances. The air gap must be installed according to manufacturer’s

instructions.

PREPARE DISHWASHER ENCLOSURE

• The rough cabinet opening must be at least 24" deep, 24"

wide and approximately 34-1/2" high from floor to underside

of the countertop.

CLEARANCES:

• When installed into a corner,

allow 2" min. clearance

between dishwasher and

DGMDFHQWFDELQHWZDOORURWKHU

appliances. Allow 25-1/2" min.

clearance from the front

of the dishwasher for door

opening. Figure B.

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 12' distance to drain.

• Drain connection height is not to exceed 72" above bottom

of dishwasher.

NOTE: Air gap must be used if waste tee or disposer

connection is less than 18" above floor to prevent siphoning.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18" above floor?

If the answer to either question is YES, Method 1 MUST

be used.

• If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2" diameter hole in the cabinet wall within

the shaded areas shown in Figure A for the drain hose

connection. The hole should be smooth with no sharp edges.

IMPORTANT – When

connecting drain line to disposer,

check to be sure that drain plug has

been removed. DISHWASHER WILL

NOT DRAIN IF PLUG IS LEFT IN PLACE.

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed before

attaching dishwasher drain hose to the disposer.

Figure D

• The dishwasher must be installed so that drain hose is no

more than 12' in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides and

back, and must not support any part of the enclosure.

32"

Min.

18"

Min.

Drain Hose Hanger

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

25-1/2"

Figure C

Installation Preparation

Remove

Drain

Plug

32"

Min.

18"

Min.

Drain Hose Hanger

7RUHGXFHWKHULVNRIHOHFWULFVKRFN¿UHRULQMXU\WRSHUVRQVWKH

installer must ensure that the dishwasher is completely enclosed at

the time of installation.

24"

Min.

This Wall Area

must be Free

of Pipes or

wires

Plumbing and Electric Service

Must Enter Inside This Area

24"

Min.

Cabinets

Square

and

Plumb

34-1/2" 1/4"

Underside of

Countertop

to Floor

Figure A

33-1/2” to 34-3/4”

Underside of

Countertop

to Floor

Figure B

WARNING

For models equipped with power cord: Do not modify the plug

provided with the appliance; if it will not fit the outlet, have a

proper outlet installed by a qualified technician.

Cabinet Preparation & Wire Routing

• The wiring may enter the opening from either side, rear or the

floor within the shaded area illustrated above in Figure E and

defined in Figure A.

• Cut a 1-1/2" maximum diameter hole to admit the electrical

cable. Edges of hole should be smooth and rounded.

Permanent wiring connections may pass through the same

hole as the drain hose and hot water line, if convenient. If

cabinet wall is metal, the hole edge must be covered with a

bushing.

NOTE: Power cords with plug must pass through a separate

hole in the cabinet.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed as

shown in Figure E. Cable must extend a minimum of 24" from

the rear wall.

• For power cord connections, install a 3-prong grounding

type receptacle in the sink cabinet rear wall, 6" min. or 18"

maximum from the opening, 6" to 18" above the floor.

• Use only WX09X70910 or WX09X70911 Dishwasher Power

Cord Kit.

PREPARE ELECTRICAL WIRING

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz., and

connected to an individual properly grounded branch circuit,

protected by a 15- or 20-ampere circuit breaker or time-delay

fuse.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).

• If the electrical supply does not meet the above requirements,

call a licensed electrician before proceeding.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and be

connected to the equipment-grounding terminal or lead on

the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and

grounded in accordance with all local codes and ordinances.

White

18"

24"

from Wall

from

Cabinet

Alternate Receptacle

Location in Adjacent

Cabinet

Ground

Black

1-1/2" Dia. Hole (Max.)

18"

Receptacle

Location

Area

Figure E

Installation Preparation

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker

before beginning installation. Do not use an extension cord or

adapter plug with this appliance.

The improper connection of the equipment grounding conductor

FDQUHVXOWLQDULVNRIHOHFWULFVKRFN&KHFNZLWKDTXDOL¿HG

electrician or service representative if you are in doubt that the

appliance is properly grounded.

WARNING

PREPARE HOT WATER LINE

NOTE: GE recommends copper tubing for the water line, but if

\RXFKRRVHWRXVHÀH[LEOHKRVHXVH*(·VWX28X326ÀH[LEOH

braided hose.

• The water supply line (3/8” copper tubing or flexible braided

hose) may enter from either side, rear or floor within the

shaded area shown in Figure F.

• The water supply line may pass through the same hole as the

electrical cable and drain hose. Or, cut an additional 1-1/2"

diameter hole to accommodate the water line. If power cord

with plug is used, water line must not pass through power

cord hole.

Figure F

Water Line Connection

• If using a flexible braided supply hose, label the hose with the

installation date to use as reference. Flexible braided hoses,

elbows and gaskets should be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such

as under the sink. (Optional, but strongly recommended and

may be required by local codes.)

• Water connection is on the left side of the dishwasher. Install

the hot water inlet line, using no less than 3/8" copper tubing

or a flexible braided hose. Route the line as shown in Figure F

and extend forward at least 19" from rear wall.

$GMXVWZDWHUKHDWHUIRU)WR)WHPSHUDWXUH

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

Turn page to begin dishwasher installation.

Cabinet Face

Shut-off

Valve

2" From Floor

19" From Wall

From

Cabinet

1-1/2" Dia.

Hole

Hot

Installation Preparation

Do not remove wood base until you are ready to install the

dishwasher. The dishwasher will tip over when the door is

opened if base is removed.

CAUTION

NOTE: If installing a Cus-

tom Door Panel (available

on some models), please

follow the instructions

found in the Custom Door

Panel kit WX35X20417.

• With dishwasher on

the wood base, check

the door balance by

opening and closing

the door.

• Door is properly

balanced if, when

opened, it self closes within 20° from vertical, stays in position

from 20° to 70° and falls fully open beyond 70°.

• If necessary increase or decrease tension as shown. Some

models will have 1 spring on each side and other models will

have 2 springs on one side and 1 spring on the other side.

/DWFKGRRUDQGDGMXVWVSULQJVWRFRUUHFWEDODQFH

Dishwasher Installation

• Screw leveling legs back into the dishwasher frame,

approximately 1/2" from frame as shown.

NOTE:6RPHPRGHOVKDYHUHDUDGMXVWDEOHOHYHOLQJZKHHOVDQG

will not require the 2 rear leveling legs.

Approx.

1/2"

STEP 3: REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT – 'RQRWNLFNRȺZRRGEDVH

Damage will occur.

• Move the dishwasher close to the installation location and lay

it on its back. NOTE: Do not place the dishwasher on its side.

• Remove the 4 leveling legs on the underside of the wood base

with a 15/16" socket wrench.

• Discard base.

STEP 1: PREPARATION

Locate the items in the installation package:

• Screws

• Junction box cover

• Drain hose and clamp

• Mounting brackets

• Trim pieces (on some models)

• Drain hose hanger

• Owner's Manual

• Product samples and/or coupons

Figure I

Toekick

Remove 2

Toekick Screws

STEP 4: REMOVE TOEKICK

• Remove the 2 toekick screws and toekick. Set aside for use in

Step 23.

Figure J

Tip: Make sure door opens and closes smoothly.

Check door opening and closing. If door does not open easily or

falls too quickly, check spring cable routing. The cable is held in

place by “shoulders” on the pulley. Check to be sure cable has

not slipped over the pulley shoulders and is routed as shown.

STEP 2: CHECK DOOR BALANCE

Figure G

Door

closes

within

20°

Door stays in

position from

20° to 70°

Door falls fully

open beyond 70°

Side View

Figure H

Side View

Custom

door

panel

Spring

hooked

to hole

inside rail

NOTE: The number of

springs, on each side,

will vary by model.

Front View

Make sure pully

cables are within

pulley shoulders

Increase

Tension

Decrease

Tension

STEP 7: INSTALL DRAIN HOSE TO DRAIN

LOOP

Connect drain loop end to drain hose using the screw clamp

as shown in the figure.

STEP 6: INSTALL 90° ELBOW

• Thread 90° elbow

onto the water valve.

Ensure rubber gasket

is located between

valve and elbow.

• Do not overtighten

elbow. Water valve

bracket could

bend or water valve

fitting could break.

• Position the end of

the elbow to face the

rear of the dishwasher.

STEP 5: IF NECESSARY, REMOVE FLOOR

PROTECT PAN (on some models)

• Disconnect leak sensor wire

(on some models).

• Pull floor protect pan forward and slide

it from under the dishwasher.

• Set aside for use in Step 21.

Dishwasher Installation

Figure N

STEP 9:

INSTALL DRAIN HOSE,

THROUGH CABINET

• Position dishwasher in front of cabinet opening. Insert drain

hose into the hole in cabinet side. If a power cord is used,

guide the end through a separate cabinet opening.

STEP 8: POSITION WATER LINE

AND HOUSE WIRING

• Position water supply line and house wiring on the floor of

the opening to avoid interference with base of dishwasher

and components under dishwasher.

Figure O

Water

Line

House

Wiring

7LS3UHYHQWXQQHFHVVDU\VHUYLFHFDOOFKDUJHVIRU¿OOGUDLQ

or noise concerns.

Position utility lines so they do not interfere with anything

under or behind the dishwasher.

Figure M

Water Valve

Bracket

90° Elbow

Fill Hose

Front of dishwasher

NOTE: The high drain loop on the side of the tub is designed for

better wash performance. Do not remove from the side of the tub.

Squeeze connector at top

to release snap feature

Figure P

House

Wiring

Power Cord

(If used)

Drain

Hose

Water

Line

Insulation

Blanket

Ensure drain hose is not

twisted or pinched

Maximum drain hose

length is 15'

Do not disconnect or remove high

drain loop from left side of dishwasher

Floor Protect Pan

Leak Sensor

Figure L

Dishwasher Installation

STEP 10: SLIDE DISHWASHER THREE-FOURTHS

OF THE WAY INTO CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

• Grasp the sides of the

front panel and slide

dishwasher into the

opening a few inches

at a time.

• As you proceed, pull the drain hose through the opening under the

sink. Stop pushing when the dishwasher extends about 6 inches

IRUZDUGRIDGMDFHQWFDELQHWV

• Make sure drain hose is not kinked under or behind the dishwasher.

• Make certain the house wiring, drain line and water line do not

interfere with components under dishwasher.

STEP 11: INSTALL TRIM PIECES

In this step you will need the trim pieces set aside in Step 1.

STEP 12: INSTALL MOUNTING BRACKETS

You will need the mounting brackets and 2 #8 hex-head screws set

aside in Step 1.

You must install the mounting brackets onto the dishwasher tub

frame top or sides prior to sliding the dishwasher into place under

the countertop. This dishwasher is capable of a true-flush installation

at a 24” deep opening. The mounting brackets have several

available attachment positions to accommodate different cabinet

constructions.

Install mounting brackets on top if the underside of

countertop is wood or wood-like material that accepts screws:

IMPORTANT - After installing brackets and before

FORVLQJWKHGLVKZDVKHUGRRUDGMXVWWKHEUDFNHWVE\EHQGLQJ

them up as needed, so that they do not contact the top of the

dishwasher door and cause damage.

• If you are installing the dishwasher under a counter with a short

overhang, the countertop brackets may extend beyond the edge

of the counter. If this is the case, remove the excess length by

repeatedly bending the brackets at the front notch only until they

break.

Install mounting brackets on sides if the countertop is

granite or similar material that will not accept wood screws:

%UHDNRȺIURQWSRUWLRQRIWKHWDEZLWKSOLHUVDWWKHORFDWLRQVKRZQ

prior to attaching to dishwasher.

• Position the left-hand side bracket as shown. Repeat with the right

bracket.

Dishwasher

tub frame

#8 Bracket

Screw

Bracket

Bend and break here

after installing if

counter has a short

overhang.

Top Mounting

• Select the top trim piece (See Figure R) and line up center to the top

ODWFK3UHVVWKHWULPSLHFHRQWRWKHWXEÀDQJHPRYLQJIURPRQHVLGH

to the other.

• Select the left trim piece (see Figure R).Align top edge with the top

WULPDQGSUHVVLWRQWRWKHOHIWVLGHRIWKHWXEÀDQJHPRYLQJIURPWKH

WRSWRWKHERWWRP5HSHDWIRUWKHULJKWVLGHWXEÀDQJHWULPSLHFH

(See Figure R for right side trim piece.)

Figure S

Figure Q

Do not push against

front door panel with

knee. Damage to the

door panel will occur.

Side Trim

Figure R

Side

Trim

Top View

Side

Trim

Top Trim

)XOO\VHDWWRWXEÀDQJH

Figure T

Bracket

Dishwasher

tub frame

#8 Bracket

screw as

supplied

Side Mounting

Bend and break

here if necessary

Care should be taken to

ensure mounting screws

do not damage cabinetry

Do not pinch

the latch

wires in

#8 bracket

screw

Tub trim

Top

View

Handle

Door

Tub trim

Tub frame

STEP 13: PUSH DISHWASHER INTO

FINAL POSITION

• Check the tub insulation blanket, if equipped, to be sure it is

smoothly wrapped around the tub. It should not be “bunched

up” and it must not interfere with the door springs. If the

insulation is “bunched up” or interfering with the springs,

straighten and recenter the blanket prior to sliding the

dishwasher into its final position.

• Slide the dishwasher into the final position by pushing on

the sides of the door panel. Do not push or pull the door

in a partially open or closed position when moving the

dishwasher. Do not use a knee or push on the center of the

panel. If you do, damage to the panel will likely result. Check

that the dishwasher is squarely positioned in the cabinet

opening at both the top and the bottom of the appliance prior

to mounting to the cabinet.

IMPORTANT – Before opening the dishwasher door,

be certain the edges of the dishwasher door panel are behind

WKHIDFHRIWKHDGMDFHQWFDELQHWDQGQRWXSDJDLQVWWKHFDELQHW

face. Refer to Figure U. If the dishwasher door is opened

when the edge of the door is against the face of the cabinet,

dishwasher door damage and cabinet damage will occur.

Figure U

Dishwasher Installation

Tip: Prevent unnecessary service charges for panel damage

or wash performance.

Check dishwasher alignment prior to opening dishwasher door

to prevent panel damage.

Make sure utility lines are not trapped or crushed behind

dishwasher. Crushed lines will restrict water flow.

Door Catches

on Cabinet Frame

Correct

Alignment

Incorrect Alignment

will result in door damage

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

• Open and close the dishwasher door to be sure it operates

VPRRWKO\DQGGRHVQRWUXERQWKHDGMDFHQWFDELQHW

Check that tub trim does not

contact the door at all points

Tub trim may be trimmed if

necessary to ensure proper door

operation

Top

View

Handle

Door

Tub trim

Tub frame

Do not allow tub trim to get

trapped by or come into contact

with the door

Top

View

Tub trim

trapped

E\GRRU

STEP 14: LEVEL DISHWASHER

IMPORTANT –

Dishwasher must be level for

proper dish rack operation,

wash performance and door

operation. The dishwasher

must be leveled left to right

and front to back. This

ensures the dish racks will

not roll in or out on their own,

FLUFXODWLRQZDWHUZLOOÀRZWR

the pump inlet, and the door

will close without hitting the

side of the tub.

• Remove the lower dish rack

and place a level on the

door and lower rack track

as shown in Figure V.

• If your model has rear

wheels, the height of

WKHZKHHOVDUHDGMXVWHG

from the front of the

dishwasher along

with the 2 front legs

on the bottom of the

dishwasher. Begin the

leveling process with the

front legs by individually

turning the front 2 legs.

%\DGMXVWLQJWKHIURQW

legs first, access to the rear leveling bolts is maximized easing rear

ZKHHODGMXVWPHQW:KHQWKHIURQWOHJVDUHDGMXVWHGWRDKHLJKW

resulting in an appropriate gap to the upper cabinet, proceed to

DGMXVWWKHUHDUOHYHOLQJZKHHOVE\DGMXVWLQJWKHOHYHOLQJEROWVDV

LOOXVWUDWHGLQ)LJXUH:,QGLYLGXDOO\WXUQWKHEROWVWRDGMXVWWKH

rear wheels. Slowly rotate the 2 bolts counter clockwise to raise

the back of the dishwasher, and clockwise to lower it. Continue

WRDGMXVWWKHIHHWDQGZKHHOVXQWLOWKHGLVKZDVKHULVOHYHODV

illustrated in Figure W. Ensure all 4 legs/wheels are firmly in contact

with the floor.

•

If your model has

4 leveling feet,

DGMXVWWKHOHYHORI

the dishwasher by

individually turning the

4 legs on the bottom

of the dishwasher as

illustrated in Figure WW.

• The dishwasher is properly leveled when the level indicator is

centered left to right and front to back. Also, the dishwasher door

should close without hitting the side of the tub.

• Replace the lower rack.

• Pull each rack out, about halfway. Check to be sure it does not

 UROOEDFNRUIRUZDUGRQWKHGRRU,IWKHUDFNPRYHVDGMXVW 

leveling legs.

Dishwasher Installation

Figure V

Tip: Prevent unnecessary service charges. Verify dishwasher is leveled.

Pull the dish racks half way out. They should stay put. Open and

FORVHWKHGRRU7KHGRRUVKRXOG¿WLQWKHWXERSHQLQJZLWKRXW

hitting the side of the tub. If the racks roll on their own, or the door

hits the side of tub, relevel the dishwasher.

$GMXVW

Figure W

$GMXVW

Figure WW

STEP 15: POSITION DISHWASHER, SECURE

TO COUNTERTOP OR CABINET

In this step you will need the 2 Phillips special head screws

from the screws set aside in Step 1.

The dishwasher must be secured to the countertop or the

cabinet sides. When the underside of the countertop is wood,

use Method 1. Use Method 2 when the underside of the

countertop is made of a material, such as granite, that will not

accept wood screws.

IMPORTANT – Prevent door panel and control

panel damage. Dishwasher must be positioned so the front

SDQHODQGFRQWUROSDQHOGRQRWFRQWDFWWKHDGMDFHQWFDELQHWV

or countertop. Mounting screws must be driven straight and

flush. Protruding screw heads could scratch the door panel or

control panel and interfere with door operation.

Method 1

Secure dishwasher to underside of wood countertop.

• Recheck alignment of the dishwasher in the cabinet. Refer to

Steps 13 and 14. Door panel and/or control panel must not

hit cabinets or countertop.

• Fasten the dishwasher to the underside of the countertop

ZLWKWKH3KLOOLSVVSHFLDOKHDGVFUHZV5HIHUWR¿JXUH

0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage.

• Install plug buttons to the side of the tub well in the holes

provided.

Method 2

Secure dishwasher to cabinet sides.

• Recheck alignment of the dishwasher in the cabinet. Refer

to Steps 13 and 14. Door panel and/or control panel must

not hit cabinets or countertop.

)DVWHQWKHGLVKZDVKHUWRWKHDGMDFHQWFDELQHWVZLWKWKH

2 Phillips special head screws provided. Refer to Figure X.

0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage. Do not screw into the cabinet face frame.

• Install plug buttons to the side of the tub well in the holes

provided.

STEP 16: CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

$WWDFKQXWWRHOERZXVLQJDQDGMXVWDEOHZUHQFK

If using a copper tubing connection:

• Slide compression nut, then ferrule over end of water line.

• Insert water line into 90° elbow.

• Slide ferrule against elbow and secure with compression nut.

IMPORTANT – Check to be sure that door spring

DQGRUGRRUVSULQJFDEOHGRQRWUXERUFRQWDFWWKH¿OOKRVHRU

water supply line.

Test by opening and

closing the door.

Reroute the water

supply lines if a

rubbing noise or

interference

occurs.

Dishwasher Installation

Figure Y

Compression

Nut

Hot Water

Supply Line

90° Elbow

Ferrule

Bottom Left Side

• Re-check that the dishwasher is squarely positioned in the

cabinet at both the top and bottom of the appliance after

PRXQWLQJWRWKHFDELQHWVFRXQWHUWRS$GMXVWLIQHFHVVDU\

• Confirm all leveling legs are in contact with the floor to

prevent the dishwasher from rocking and ensure proper door

and latch operation

Brackets

Wood Countertop

Figure X

Granite Countertop

Side Brackets

Solid Surface Countertop

Dishwasher Installation

• Connect drain line to air gap, waste tee or disposer using the

previously determined method. Secure hose with a screw-

type clamp.

Waste Tee Installation

Method 1 – Air gap with waste tee or disposer

Disposer Installation

Waste Tee Installation

Method 2 – “High drain loop” with waste tee or disposer

With this method you will need the drain hose hanger set aside

in Step 1.

Fasten drain hose to underside of countertop with the provided

hanger.

Disposer Installation

Figure AB

Figure AC

IMPORTANT – When connecting drain line to

disposer, check to be sure that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE.

STEP 17: CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8" through 1"

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port.

• Cut drain hose connector on the marked line, if required,

WR¿WWKHLQOHWSRUW

• If a longer drain hose is required and you did not purchase

drain hose WD24X10065, add up to 66" length for a total of

144" (12 feet) to the factory-installed hose. Use 5/8" or 7/8"

inside diameter hose and a coupler to connect

the 2 hose ends.

Secure the

connection

with hose

clamps.

Figure Z

Figure AA

7^bT2[P\_

2^d_[Ta

7^bT2[P\_

Remove

Drain

Plug

Tip: Avoid unnecessary service call charges for a no drain

complaint.

Make sure excess drain hose has been pulled through

the cabinet opening. This will prevent excess hose in the

dishwasher cavity from becoming kinked or crushed by the

dishwasher.

Cutting Line

5/8"

IMPORTANT: Do not cut corrugated

portion of hose

18"

Min.

32"

Min.

32"

Min.

18"

Min.

Drain Hose Hanger

NOTES:

• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED 72" ABOVE

BOTTOM OF DISHWASHER.

• TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 12 FEET FOR

PROPER DRAIN OPERATION.

STEP 19: PRETEST CHECKLIST

Review this list after installing your dishwasher to avoid

charges for a service call that is not covered by your

warranty.

• Check to be sure power is OFF.

• Open door and remove all foam and paper packaging.

• Locate the Owner’s Manual set aside in Step 1.

• Read the Owner’s Manual for operating instructions.

• Check door opening and closing. If door does not open and

close freely, check for proper routing of spring cable over

SXOOH\,IGRRUGURSVRUFORVHVZKHQUHOHDVHGDGMXVWVSULQJ

tension. See Step 2.

• Check to be sure that wiring is secure under the dishwasher,

not pinched or in contact with door springs or other

components. See Step 18.

• Check door alignment with tub. If door hits tub, level

dishwasher. See Step 14.

• Check door alignment with cabinet. If door hits cabinet,

reposition dishwasher. See Step 13.

• Check that door spring does not contact water line, fill hose,

wiring or other components. See Step 13.

• Verify water supply and drain lines are not kinked or in

contact with other components. Contact with motor or

dishwasher frame could cause noise.

• Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must be between

120°F and 140°F. A minimum of 120°F temperature is

required for best wash performance. See “Prepare Hot Water

Line,” page 5.

• Add 1 quart of water to the bottom of the dishwasher to

lubricate the pump seal.

• Turn on water supply. Check for leaks. Tighten connections if

needed.

• Remove protective film if present from the control panel and

door.

• Check that tub trim does not contact the door.

Dishwasher Installation

STEP 18: CONNECT POWER SUPPLY

If a power cord with plug is already installed proceed to

Step 19.

,QWKLVVWHS\RXZLOOQHHGWKHMXQFWLRQER[FRYHUDQGWKH

#10 Hex head screw from the screws set aside in Step 1.

6HFXUHKRXVHZLULQJWRWKHEDFNRIWKHMXQFWLRQER[ZLWKD

strain relief.

• Locate the 3 dishwasher wires, (white, black and green) with

WKHVWULSSHGHQGVFRPLQJRXWRIWKH$&MXPSHU8VH8/OLVWHG

wire nuts of appropriate size to connect incoming ground to

green, white to white and black to black.

,QVWDOOWKHMXQFWLRQER[FRYHUXVLQJKH[KHDGVFUHZ

Check to be sure that wires are not pinched under the cover.

0DNHVXUHWKDWWKHMXQFWLRQER[FRYHULVUHVWLQJRQWKH

mounting bracket.

• If using a Power Cord Kit, use GE part number WX09X70910

or WX09X70911 and refer to the included instructions.

If house wiring is not 2-wire with ground, a ground must be

provided by the installer. When house wiring is aluminum, be sure

to use UL-Listed anti-oxidant compound and aluminum-to-copper

connectors.

Figure AD

Ground

(Green)

NOTE: Do not remove the

Junction Box Bracket.

Jumper

Junction Box

Bracket

Black

White

Ground Screws

NOTE: All ground screws, brackets and wires must remain

intact.

WARNING

Dishwasher Installation

STEP 20: DISHWASHER WET TEST

• Turn on power supply or plug power cord into outlet,

if equipped.

• Select a cycle to run and push the Start button.

• Ensure the door is latched. Dishwasher should start.

• Check to be sure that water enters the dishwasher. If water

does not enter the dishwasher, check to be sure that water

and power are turned on.

• Check for leaks under the dishwasher. If a leak is found, turn

off power at the breaker, and then tighten water connections.

Restore power after leak is corrected.

• Check for leaks around the door. A leak around the door could

be caused by door rubbing or hitting against

DGMDFHQWFDELQHWV5HSRVLWLRQWKHGLVKZDVKHULIQHFHVVDU\

See Step 13.

• Press and hold the Start button for 3 seconds to cancel

the cycle. The unit will begin to drain. Check drain lines. If

leaks are found, turn off power at the breaker and correct

plumbing as necessary. Restore power after corrections are

made. See Steps 7, 8, 9, 10 and 17.

• Open dishwasher door and make sure all of the water has

drained. If not, check that disposer plug has been removed

and/or air gap is not plugged. Also check drain hose to be

sure it is not kinked underneath or behind dishwasher. See

Step 17.

• Press Start button once again and run dishwasher through

another cycle. Check for leaks and correct if required.

• Repeat this step as necessary.

STEP 21:

REPLACE FLOOR PROTECT PAN

(on some models)

6OLGHWKHÀRRUSURWHFWSDQXQGHUWKHGLVKZDVKHUXQWLOLWVVLGH

lock slots are close to engaging the side mounting tabs on

the dishwasher.

• Lift the pan until its lock slots contact the mounting tabs and

push the pan back to engage them.

• When properly installed, the top of the lock slots will be over

the mounting tabs.

• Connect the leak sensor connector to the leak sensor

(on some models).

Floor Protect Pan

Figure AE

Floor Protect Pan

Front

Rear

Mounting Tab

Two on each side

of the dishwasher

Lock Slots

Two on each side of

the floor protect pan

Leak Sensor

(on some models)

Lock Slot

Mounting

Tab

Dishwasher Installation

STEP 23: REPLACE TOEKICK

• Place toekick against the legs of the dishwasher.

Figure AH

Attachment

Screws

Toekick

• Align the toekick with the bottom edge and make sure it is

DJDLQVWWKHÀRRU

• Insert and tighten the 2 toekick attachment screws. The

WRHNLFNVKRXOGVWD\LQFRQWDFWZLWKWKHÀRRU

Tip: Reduce sound from under the dishwasher. Make sure

toekick is against floor.

STEP 25: LITERATURE

• Be sure to leave complete literature package, these

Installation Instructions and product samples and/or coupons

with the consumer.

STEP 24: CHECK THE FOLLOWING

• Tub trim does not interfere with the door

• Dishwasher is square and level at both the top and bottom of

the cabinet opening, with no twisting or distortion of the tub

or door

$OOOHJVRIWKHGLVKZDVKHUDUH¿UPO\LQFRQWDFWZLWKWKHÀRRU

• Drain hose is not pinched between the dishwasher and

DGMDFHQWFDELQHWVRUZDOOV

7XEWULPLVIXOO\VHDWHGRQWKHWXEÀDQJH

STEP 22:

POSITION SOUND INSULATION

PIECE (on some models)

• Locate the sound insulation package inside the dishwasher.

• Stand the parts upright as shown.

• Locate the control box.

• Push insulation block portion under the dishwasher until it is

beneath the control box.

• Push the panel portion up to the front of the block.

• Tuck the sides of the front panel behind the toekick

attachment screw holes.

• Open door all the way, if the door doesn’t stay fully open,

DGMXVWWKHLQVXODWLRQSDQHO

• Align the screw holes with the screw holes on the legs of the

dishwasher.

• Ensure vent opening is not blocked by insulation.

Control Box

Figure AG

Figure AH

Push the sides of the insulation behind

the toekick attachment screw holes

(on some models)

Toekick

Insulation Block

(On some models.)

Dishwasher

Door

Figure AF

Vent opening

Location and appearance will vary

Appliance Park

Louisville, KY 40225

GEAppliances.com

NOTE: While performing installations described in

this book, safety glasses or goggles should be worn.

NOTE: Product improvement is a continuing

endeavor at GE Appliances. Therefore, materials,

DSSHDUDQFHDQGVSHFLILFDWLRQVDUHVXEMHFWWRFKDQJH

without notice.

Directives d’installation

Lave-vaisselle encastré

Pour toute question, composez le 1.800.561.3344 ou visitez notre site Web:

www.electromenagersge.ca

POUR VOTRE SÉCURITÉ

Veuillez lire et observer toutes les mises en garde

(AVERTISSEMENT et ATTENTION) données dans les présentes

directives. Pour effectuer l’installation décrite dans les présentes

directives, il faut porter des gants et des lunettes de sécurité.

IMPORTANT – Observez tous les codes et

ordonnances en vigueur.

• Note à l’installateur – Veuillez laisser les présentes directives

au consommateur pour l’inspecteur local.

• Note au consommateur – Veuillez conserver les présentes

directives avec votre Manuel d’utilisation pour consultation

ultérieure.

• Compétences requises – L’installation de ce lave-vaisselle

exige des compétences de base en mécanique, en électricité

et en plomberie. L’installateur est responsable de la qualité

de l’installation. Toute défaillance du produit attribuable

à une installation inadéquate n’est pas couverte par la

garantie de GE. Reportez-vous à la garantie du produit.

• Durée de l’installation – Entre 1 et 3 heures. L’installation

d’un nouveau lave-vaisselle exige plus de temps que

le remplacement d’un ancien modèle.

IMPORTANT – Le lave-vaisselle DOIT être installé de

manière à ce qu’il puisse être sorti de son emplacement si des

réparations sont nécessaires.

Il importe d'user de prudence lorsque l'appareil est installé

RXGpSODFpD¿QGHSUpYHQLUOHQGRPPDJHPHQWGXFRUGRQ

d'alimentation.

Si le lave-vaisselle que vous avez reçu est endommagé,

communiquez immédiatement avec votre détaillant ou

l’entrepreneur en construction.

Accessoires facultatifs – Reportez-vous au Manuel d’utilisation pour

FRQQDvWUHOHVHQVHPEOHVSRXUSDQQHDXGpFRUDWLISHUVRQQDOLVpRȺHUWV

9RWUHODYHYDLVVHOOHHVWXQDSSDUHLOTXLFKDXȺHO·HDX

VEUILLEZ LIRE ATTENTIVEMENT

CONSERVER CES DIRECTIVES

AVANT DE COMMENCER

Veuillez lire attentivement toutes les directives

qui suivent.

ARRÊT

• Pour réduire les risques de choc électrique, d’incendie

ou de blessures, l’installateur doit s’assurer que le lave-

vaisselle est complètement encastré au moment de

l’installation.

• POUR VOTRE SÉCURITÉ PERSONNELLE: Enlevez le fusible

ou déclenchez le disjoncteur au panneau de distribution

principal avant de commencer l’installation. N’utilisez pas

XQHUDOORQJHpOHFWULTXHRXXQDGDSWDWHXUGH¿FKHDYHF

cet appareil.

• Un branchement inadéquat du conducteur de mise à la

terre peut présenter des risques de choc électrique. Si

vous n’êtes pas certain que l’appareil est correctement

mis à la terre, consultez un réparateur ou un électricien

TXDOL¿p

• Si le câblage électrique de la résidence n’est pas constitué

GHGHX[¿OVSOXVXQ¿OGHPLVHjODWHUUHO·LQVWDOODWHXUGRLW

LQVWDOOHUXQ¿OGHPLVHjODWHUUH6LOHFkEODJHpOHFWULTXHGH

la résidence est en aluminium, utilisez un agent antioxydant

et des connecteurs pour raccords «aluminium-cuivre»

homologués UL.

N’enlevez pas la base de bois avant d’être prêt à installer

le lave-vaisselle. Si vous enlevez la base de bois, le lave-

vaisselle pourrait basculer lorsque vous ouvrez la porte.

VÉRIFIEZ LES POINTS SUIVANTS

 La moulure de la cuve ne gêne pas la porte

 Le lave-vaisselle est d'équerre et de niveau par rapport au bas et au haut de

l'ouverture de l'armoire, sans torsion ni déformation de la cuve ou de la porte

 Les quatre (4) pieds reposent fermement sur le plancher



Le boyau de vidange n'est pas coincé entre le lave-vaisselle et les armoires ou les murs adjacents

 La moulure de cuve repose entièrement contre le bord de la cuve

AVERTISSEMENT

ATTENTION

OUTILS NÉCESSAIRES:

• Tournevis Phillips

• Tourne-écrous de 6,3 mm (1/4 po) et

de 7,9 mm (5/16 po)

• Clé à molette de 15,2 cm (6 po)

• Niveau

• Équerre de charpentier

• Ruban à mesurer

• Lunettes de sécurité

• Lampe de poche

• Seau pour recueillir l’eau lors du rinçage

de la conduite d’eau

• Clé à douille de 23,8 mm (15/16 po)

(facultatif – pour enlever la base de bois)

• Gants

• Pince

• Pour une nouvelle installation:

• Coupe-tubes

• Perceuse et forets appropriés

• Jeu de scies-cloche

Jeu de scies-cloche

Niveau

Coupure anti-

refoulement

Bague anti-traction

Boyau de vidange

Tourne-écrous

de 6,3 mm (1/4 po)

et de 7,9 mm (5/16 po)

Clé à douille de

23,8 mm (15/16 po)

Seau

Coupe-tubes

Perceuse

et forets

Lampe de poche

Gants

Tournevis

Phillips

Équerre de

charpentier

Clé à molette de

15,2 cm (6 po)

Lunettes de sécurité

Préparation pour l’installation

Ruban à mesurer

PIÈCES FOURNIES DANS L’EMBALLAGE:

• Couvercle de la boîte de jonction et vis à tête

hexagonale n° 10

• Collier

• Boyau de vidange (147 cm/58 po de long)

• Support de tuyau de vidange

• 2 Vis à tête hexagonale no 8-18 pour fixer les

supports au cadre de la cuve du lave-vaisselle

• 2 Boutons de bouchon

• 2 Moulures latérales

• 1 Garniture supérieure (certains modèles)

• 2 Supports de montage pour comptoirs ou armoires

latérales en bois

• 2 Vis à tête spéciale Phillips n° 8-18 x 15,8 mm

(5/8 po) pour fixer le lave-vaisselle au dessous

du comptoir ou armoires latérales

• Documentation, échantillons et(ou) bons

MATÉRIEL NÉCESSAIRE:

• Coude de 90° (19,1 mm [3/4 po] filet pour tuyau d'arrosage

de jardin à une extrémité et l’autre extrémité conçue pour le

raccordement à la conduite d’alimentation en eau)

• Connecteurs vissables homologués UL (3)

• Ruban-cache

Pour une nouvelle installation:

• Coupure anti-refoulement pour le boyau de vidange, si

nécessaire

• Raccord en T pour la plomberie de la résidence, s’il y a lieu

•

Câble électrique ou Trousse de cordon d’alimentation WX09X70910

(5,4 pi) ou WX09X70911 (7,9 pi) en fonction de votre installation.

• Colliers à vis sans fin

• Bague anti-traction pour le raccordement électrique

• Robinet d’arrêt (recommandé)

• Conduite d’eau chaude – 9,5 mm (3/8 po) minimum, tuyau

en cuivre (incluant la bague et l’écrou à compression) ou la

pièce WX28X326GH*(ER\DXPpWDOOLTXHÀH[LEOH

• Boyau de vidange de 3,7 m (12 pi) de long WD24X10065, si

nécessaire

Vis à tête spéciale

Phillips n° 8

de 15,8 mm (5/8 po)

de long

Vis à tête

hexagonale n° 10

de 12,7 mm (1/2 po)

de long pour boîte

de jonction

Boyau de

vidange facultatif

WD24X10065

&ROOLHUVjYLVVDQV¿Q

Raccord en T

Câble électrique (ou

cordon d’alimentation,

s’il y a lieu)

Connecteurs

vissables (3)

Collier

Couvercle de la

boîte de jonction

et vis à tête

hexagonale n° 10

Supports de

montage

Support de tuyau

de vidange

Vis à tête hexagonale

n° 8 pour support de

montage

Pince

Robinet

d’arrêt

Documentation

Coude de 90°

Garniture (supérieure)

(certains modèles)

Moulures latérales

Conduite d’eau

chaude

Raccord pour boyau

de vidange facultatif

Boutons de

bouchon

Ruban-cache

(s'il y a lieu)

Méthode n° 1 – Coupure anti-refoulement avec raccord en T ou

broyeur à déchets

Il faut installer une coupure anti-refoulement lorsqu’elle est exigée par

les ordonnances et les codes locaux en vigueur. Cette coupure anti-

refoulement doit être installée conformément aux directives données

par le fabricant.

PRÉPARATION DE L’OUVERTURE DANS

LES ARMOIRES

• L’ouverture dans les armoires doit mesurer au moins

61,0 cm (24 po) de largeur et de profondeur, et environ

87,6 cm (34-1/2 po) de hauteur à partir du plancher

jusqu’au-dessous du comptoir.

EXIGENCES RELATIVES AU SYSTÈME

DE VIDANGE

• Veuillez observer les ordonnances et les codes locaux en vigueur.

• Le boyau de vidange doit avoir une longueur maximale de

3.66 mètres (12 pieds).

• Le boyau de vidange ne doit pas être raccordé à une hauteur

dépassant 1,8 m (72 po) au-dessus du bas du lave-vaisselle.

REMARQUE: Il faut installer une coupure anti-refoulement si le

raccord au broyeur à déchets ou au raccord en T se trouve à moins

de 46 cm (18 po) au-dessus du plancher afin d’éviter un siphonage.

CHOIX DE LA MÉTHODE DE VIDANGE

Le type d’installation de vidange dépend des conditions suivantes.

• Les ordonnances ou codes locaux en vigueur exigent-ils

une coupure anti-refoulement?

• Le raccord en T se trouve-t-il à moins de 46 cm (18 po)

du plancher?

Si vous répondez OUI à l’une ou l’autre de ces questions,

vous DEVEZ utiliser la méthode n° 1.

• Si vous répondez NON, vous pouvez employer l’une ou l’autre

des méthodes.

PRÉPARATION DES ARMOIRES

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre dans la paroi de

l’armoire qui se trouve dans la partie ombrée de la Figure A pour

le boyau de vidange. Assurez-vous que l’orifice ne présente pas

d’arêtes vives.

IMPORTANT – Lorsque vous

branchez le boyau de vidange à un

broyeur à déchets, assurez-vous d’enlever

le bouchon de vidange. LE LAVE-VAISSELLE

NE POURRA PAS SE VIDER SI VOUS LAISSEZ

LE BOUCHON EN PLACE.

Méthode n° 2 – Boucle de vidange élevée avec raccord en T ou

broyeur à déchets

Conseil: Pour éviter des frais de réparation inutiles.

Assurez-vous d’enlever le bouchon de vidange du broyeur à

déchets avant d’y brancher le boyau de vidange du lave-vaisselle.

Figure D

• Le lave-vaisselle doit être installé de façon à ce que le boyau

de vidange mesure au maximum 3.66 mètres (12 pieds) pour

assurer une vidange adéquate.

• Le dessus, les côtés et l’arrière du lave-vaisselle doivent

être complètement dissimulés à l’intérieur de l’ouverture.

Le lave-vaisselle ne doit soutenir aucune partie de la

structure des armoires.

Figure C

Préparation pour l’installation

Pour réduire les risques de choc électrique, d’incendie ou de

blessures, l’installateur doit s’assurer que le lave-vaisselle est

complètement encastré au moment de l’installation.

Figure A

33-1/2 po to 34-3/4 po

du dessous du

comptoir au

plancher

Le mur du fond

doit être exempt

de tuyaux ou

de fils

La partie ombrée est réservée

à la plomberie et à l’électricité

Armoires à

l’équerre et

d’aplomb

61,0 cm

(24 po) min.

15,2 cm (6 po)

61,0 cm

(24 po) min.

10,1 cm

(4 po)

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

28-3/8"

Comptoir

Lave-vaisselle

5,1 cm (2 po) minimum pour

l’ouverture de la porte

65 cm (25-1/2 po)

Remove

Drain

Plug

Enlevez le

bouchon

de vidange

32"

Min.

18"

Min.

Drain Hose Hanger

Crochet pour boyau de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

32"

Min.

18"

Min.

Drain Hose Hanger

Crochet pour boyau de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

Figure B

DÉGAGEMENTS:

• Dans le cas d’une

installation dans un

coin, veuillez prévoir un

dégagement d’au moins

5,1 cm (2 po) entre le lave-

vaisselle et les armoires, le

mur ou un électroménager

adjacent. Veuillez prévoir

un dégagement d’au moins

65 cm (25-1/2 po) à l’avant

du lave-vaisselle pour

l’ouverture de la porte.

Reportez-vous à la

Figure B.

AVERTISSEMENT

Dans le cas des modèles dotés d’un cordon d’alimentation:

Ne modifiez pas la fiche fournie avec l’appareil; si vous ne

pouvez pas la brancher dans la prise de courant, faites installer

une prise de courant appropriée par un technicien qualifié.

Préparation des armoires et cheminement des fils

• Les fils peuvent entrer dans l’ouverture du côté droit, du côté

gauche, de l’arrière ou du plancher dans la partie ombrée de

la Figure E et de la Figure A.

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre au maximum

pour le passage du câble électrique. Le bord du trou doit

être lisse et arrondi. Les fils électriques pour le branchement

permanent peuvent passer par le même trou que le boyau

de vidange et la conduite d’eau chaude, si c’est plus pratique.

Si le trou est pratiqué dans une paroi en métal, les bords de

l’orifice doivent être recouverts d’un passe-fils pour protéger

les fils.

REMARQUE: Le cordon d’alimentation doté d’une fiche doit

passer par un autre trou dans l'armoire.

Branchement électrique du lave-vaisselle

Le branchement électrique s’effectue du côté avant droit du

lave-vaisselle.

• Dans le cas d’un branchement permanent, le câble doit être

acheminé de la façon indiquée à la Figure E. Le câble doit

avoir une longueur minimale de 61 cm (24 po) à partir du mur

arrière.

• Dans le cas d’un branchement avec un cordon d’alimentation,

installez une prise de courant mise à la terre à trois broches

sur la paroi de l’armoire adjacente, entre 15 cm (6 po) et

46 cm (18 po) de l’ouverture, et entre 15 cm (6 po) et 46 cm

(18 po) du plancher.

• Utilisez uniquement WX09X70910 ou WX09X70911 Trousse

de cordon d’alimentation pour lave-vaisselle.

PRÉPARATION DU CÂBLAGE ÉLECTRIQUE

Alimentation électrique

• Cet appareil doit être alimenté par un courant de 120 V et

60 Hz, et branché à un circuit individuel correctement mis

à la terre et protégé par un disjoncteur de 15 ou 20 ampères

ou un fusible temporisé.

• Le câble électrique doit posséder deux fils, plus un fil de mise

à la terre, et résister à une température nominale de 75 °C

(167 °F).

• Si votre alimentation électrique ne répond pas à ces

exigences, appelez un électricien agréé avant de poursuivre

l’installation.

Mise à la terre – Branchement permanent

Cet appareil doit être branché à un réseau électrique

permanent mis à la terre. Sinon, il faut installer un conducteur

de mise à la terre avec les conducteurs du circuit et le brancher

à la borne de mise à la terre du réseau ou au fil de mise à la

terre de l’appareil.

Mise à la terre – Modèles dotés d’un cordon d’alimentation

Cet appareil doit être mis à la terre. En cas de mauvais

fonctionnement ou de défaillance, la mise à la terre réduira

les risques de choc électrique en fournissant au courant

électrique un circuit de moindre résistance. Cet appareil est

doté d’un cordon d’alimentation possédant un conducteur

de mise à la terre et une fiche de mise à la terre. La fiche

doit être branchée dans une mise appropriée, installée et

mise à la terre en conformité avec tous les codes locaux et

ordonnances en vigueur.

Préparation pour l’installation

POUR VOTRE SÉCURITÉ PERSONNELLE: Enlevez le fusible ou

déclenchez le disjoncteur au panneau de distribution principal

avant de commencer l’installation. N’utilisez pas une rallonge

pOHFWULTXHRXXQDGDSWDWHXUGH¿FKHDYHFFHWDSSDUHLO

Un branchement inadéquat du conducteur de mise à la terre

peut présenter des risques de choc électrique. Si vous n’êtes pas

certain que l’appareil est correctement mis à la terre, consultez

XQUpSDUDWHXURXXQpOHFWULFLHQTXDOL¿p

Figure E

Zone pour

la prise de

courant

Autre emplacement

possible pour la prise

de courant dans une

armoire adjacente

46 cm (18 po)

46 cm

(18 po)

15 cm (6 po)

15 cm

(6 po)

Trou de 3,8 cm

(1-1/2 po) de dia. (max.)

7,6 cm (3 po)

des armoires

61 cm (24 po)

du mur

Mise à la terre

Noir

Blanc

AVERTISSEMENT

La page charge ...

GE PDT845SMJES Guide d'installation

Marque: GE

Modèle: PDT845SMJES

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE PDT845SMJES Installation guide
español: GE PDT845SMJES Guía de instalación

GE PDT845SMJES Guide d'installation

GE PDT845SMJES Guide d'installation

dans d''autres langues

Documents connexes

Autres documents