Zephyr ZREM90ABSGG Mode d'emploi

Use, Care, and Installation Guide

Model number:

Serial Number:

www.zephyronline.com

DEC17.0201 © Zephyr Ventilation LLC.

Airﬂow Control Technology

TM

C

Anzio Island

ZAZ-M90CS

ZAZ-E42CS

Luce Island

ZLC-M90BS

ZLC-E42BS

Roma Island

ZRM-E36DS

ZRM-E42DS

Ravenna Island

ZRE-M90ABSGG

ZRE-E42ABSGG

www.zephyronline.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet

....................................... 5

Mounting Height & Clearance

................................ 6

Ducting Options

........................................................... 7

+RRG6SHFL¿FDWLRQV

................................................... 8-11

Mounting the Hood

..................................................... 12-13

Ductless Recirculating

.............................................. 14

FEATURES & CONTROLS

ICON Touch Controls ..................................... 15-16

MAINTENANCE

Hood and Filter Cleaning

......................................... 17

TROUBLESHOOTING

................................................................ 18

ACT CONVERSION

..................................................................... 19

FAN CURVE DIAGRAMS

......................................................... 20-21

WIRING DIAGRAM

...................................................................... 22

LIST OF PARTS AND ACCESSORIES

.............................. 23

WARRANTY

.................................................................................... 24

PRODUCT REGISTRATION

.................................................... 25

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG

F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516

,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

 7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG

 7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG

 <RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV

,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ

E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQG

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV

attics, crawl spaces or garages.

Not for use over an outdoor grill.

OPERATION

$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH

ground path is adequate.

Do not ground to a gas pipe.

&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWVSXUFKDVH

and install appropriate connector if necessary.

4

www.zephyronline.com

(3) Wire Nuts

(4) ø12 OD / ø5

ID Washers

(4) M4 x 1”

wood srews

(4) 3/16 x 1/4” flat-head

machine screws

(1) Hardware package

(1) 6” round damper (pre-installed)

PARTS SUPPLIED

HARDWARE PACKAGE CONTENTS

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

- Cable connector (if required by local codes)

- Duct cover extension accessory

- Recirculating kit accessory

(2) Top Duct Covers

(1) Top Support Frame

(2) Bottom Duct Covers

(1) Bottom Support Frame

(1) Hood Body

(2) Brite Strip™ LED

(2) Mesh Filters

(ZAZ-E42 & ZRM-E42 x 3)

(1) M4 x 12

safety screw

A

B

Front of Hood

C

L

/

Cut-Out Shaded Area

(1) Paper ceiling template

(20) M4 x 8 pan-head

machine screws

(ZLC x 8)

(2) Lateral support brackets

(ZLC ONLY)

(1) Square support bracket

(ZAZ ONLY)

(4) 3/16 x1/4 pan-head

machine scews

(ZRE only)

List of Materials

5

Duct pieces

Tot a l

Equivalent number

length x used =

3- 1/4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

Tot a l

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 100 equivalent feet.

6” round to

3- 1/4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Installation – Ducting Calculation Sheet

Installation – Mounting Height & Clearance

6

www.zephyronline.com

DUCTING

A minimum of 6” round duct is recommended to

PDLQWDLQPD[LPXPDLUÀRZHI¿FLHQF\

Always use rigid type metal ducts only. Flexible

GXFWVFRXOGUHVWULFWDLUÀRZE\XSWR

Use calculation worksheet to compute total duct

ZRUN3DJH

ALWAYS, when possible, reduce the number of

transitions and turns. If a long duct run is required,

increase duct size from 6” to 7” or 8”.

If turns or transitions are required: Install as far

away from duct opening and as far apart between

the two transitions as possible.

Minimum mount height between range top to hood

bottom should be no less than 26”.

Maximum mount height should be no higher than

34”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV

mounted too high will be hard to reach and will

ORRVHSHUIRUPDQFHDQGHI¿FLHQF\

If available, also refer to range manufacturer’s

height clearance requirements and recommended

hood mounting height above range. Always check

your local codes for any differences.

Duct cover extension kit available for ceiling

heights up to 12 feet. Turn to page 23 for part

number and ordering information.

DAMAGE-SHIPMENT / INSTALLATION:

 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH

installation.

 ,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKH

unit to the store in which it was bought for

repair or replacement.

 ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLU

or replacement is the responsibility of the

customer.

 ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU

WKDQWKHFXVWRPHUUHSDLURIUHSODFHPHQWPXVW

be made by arrangement between customer

and installer.

A

B

C

D

E

F

ZAZ ZLC ZRM

Standard Duct Cover

Extension Duct Cover

A

B

C

D

E

F

ZAZ ZLC ZRM

28”

31”

39”

90” (7’ 6”)

80”

150” (12’ 6”)

28”

90” (7’ 6”)

47”

51”

80”

150” (12’ 6”)

109” (9’ 1”)

113” (9’ 5”)

36”

50”

98” (8’ 2”)

120” (10’)

47”

51”

80”

109” (9’ 1”)

113” (9’ 5”)

150” (12’ 6”)

A : Minimum Ducted Hood Height

B : Minimum Recirculating Hood Height

C : Maximum Hood Height

D : Minimum Ducted Ceiling Height

E : Minimum Recirculating Ceiling Height

F : Maximum Ceiling Height

min. A

min. B

max. C

36”

26” min.

34” max.

min. D

min. E

max. F

31-

1/2

”

93-

1/2

” (7’ 9-

1/2

”)

32-

1/2

”

46-

1/2

”

94-

1/2

” (7’ 10-

1/2

”)

116-

1/2

” (9’ 8-

1/2

”)

93” (7’ 9”)

109” (9’ 1”)

50-

1/2

”

50-

1/2

”

112-

1/2

” (9’ 4-

1/2

”)

112-

1/2

” (9’ 4-

1/2

”)

ZRE

28-

1/2

”

39”

78”

148” (12’ 4”)

109” (9’ 1”)

48-

1/2

”

48-

1/2

”

110-

1/2

” (9’ 2-

1/2

”)

110-

1/2

” (9’ 2-

1/2

”)

28-

1/2

”

90-

1/2

” (7’ 6-

1/2

”)

90-

1/2

” (7’ 6-

1/2

”)

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid metal ductwork only.

)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZFHUWL¿HG6LOYHU7DSHRU'XFW7DSH

Some Ducting Options

Installation – Ducting Options

Roof Pitch w/

Flashing & Cap

ductless

recirculating

side wall cap

w/ gravity damper

Soffit or crawl space

(blower

housing)

8

www.zephyronline.com

Installation – +RRG6SHFL¿FDWLRQ=$=

FRONT

SIDE

TOP of HOOD

TOP SUPPORT FRAME

(top view)

C/L

8 1/8”

7 9/16”

3 9/16”

13/16”

4 3/16”

8 1/4”

STANDARD

min. ducted - 31 1/2”

min. recirc. - 36”

max. - 50”

Z1C-00AZ

min. ducted - 47”

min. recirc. - 51”

max. - 80”

10 5/8”

25 9/16”

1 3/16”

11”

35 7/16”, 41 15/16”

9 7/16”

16 9/16”

5 1/4”

5 15/16”

3 1/2”

AC In

1 1/4”

C/L

1 7/8”

5 5/16”

9

Installation – +RRG6SHFL¿FDWLRQ=/&

FRONT

SIDE

TOP of HOOD

TOP SUPPORT FRAME

(top view)

FRONT

11”

35 7/16”, 41 7/8”

9 7/16”

12

3/8”

25 9/16”

10 5/8”

STANDARD

min. ducted - 28”

min. recirc. - 32

1/2”

max. - 46

1/2”

Z1C-00LC

min. ducted - 47”

min. recirc. - 51”

max. - 80”

6”

2 1/2”

1 1/4”

3 7/16”

C/L

7 9/16”

6

3/4”

8 1/8”

7

13/16”

9 7/16”

2

1/16”

10

www.zephyronline.com

Installation – +RRG6SHFL¿FDWLRQ=50

35 7/8”, 41 7/8”

14”

3”

26 7/8”

STANDARD

min. ducted - 28”

min. recirc. - 31”

max. - 39”

Z1C-01RM EXTENSION

min. ducted - 50 1/2”

min. recirc. - 50 1/2”

max. - 80”

12”

11 3/16”

9 11/16”

AC-IN

2

CL

3/8"

4 3/16"12

7/16

"

ø 6"

11"

9 7/16"

11

Installation – +RRG6SHFL¿FDWLRQ=5(

FRONT SIDE

TOP of HOOD TOP SUPPORT FRAME

(top view)

10

3/8

”

23

15/16

”

35

3/16

”

25

9/16

”

24

1/2

”

3

9/16

”

10

7/8

”

2

3/4

”

11

5/8

”

4

3/8

”

(top of electrical box)

13

3/4

”

5/16

”

C/L

6”

8”

8 3/4”

8 1/4”

3

3/4”

4

3/16”

5/8”

elec. k/o

STANDARD

min. ducted - 28 1/2”

min. recirc. - 28 1/2”

max. - 38”

Z1C-01REBS EXTENSION

min. ducted - 48 1/2”

min. recirc. - 48 1/2”

max. - 78”

12

www.zephyronline.com

1

2

Ceiling Joists

Wood Blocking

Top Support Frame

Support Frame Arm

Bottom Support Frame

Hood Body

3

Mounting Screws

(pre-installed)

4

Installation – Mounting the Hood

 'HWHUPLQHPRXQWLQJORFDWLRQRQFHLOLQJDQGWHPSRUDULO\WDSHSDSHUWHPSODWHLQFOXGHGZLWKWKHKRRGWR

the ceiling. Cut out internal shaded area of template to allow the ducting and electrical to pass through.

,IQHFHVVDU\DGGZRRGEORFNLQJPLQ´[´WRFHLOLQJMRLVWVORFDWHGEHKLQGWKHGU\ZDOOWRUHLQIRUFHWKH

PRXQWLQJORFDWLRQ),*$6HFXUH0[´ZRRGVFUHZVWRSRLQWV$DQG%RIWKHSDSHUWHPSODWH),*

*'RQRWFRPSOHWHO\WLJKWHQVFUHZVOHDYHDSSUR[´H[SRVHG

2. Remove screws securing top and bottom support frames together. Adjust support frame to accomodate the

GHVLUHGKRRGKHLJKWDQGUHDVVHPEOHWKHIUDPHXVLQJWKHSUHYLRXVO\UHPRYHGVFUHZVVFUHZVIRUHDFK

VXSSRUWIUDPHDUP),*$

3. Lift support frame assembly up to the ceiling making sure the word “front” on the top support frame faces the

IURQWRIWKHKRRGZKHUHWKHFRQWUROVZLOOEHORFDWHG),*%7KHNH\KROHVRQWKHWRSVXSSRUWIUDPHVKRXOG

cover the wood screws previously installed in the ceiling. Slide support frame towards narrow end of key

KROHVWRORFNWKHIUDPHLQSODFH,QVWDOOWKHODVW0[´ZRRGVFUHZVZLWKZDVKHUVLQWRWKHWZRUHPDLQLQJ

corners of the top support frame to secure it to the ceiling. Tighten all screws.

=5(21/<5HPRYHDOXPLQXPPHVK¿OWHUVIURPKRRG3ODFHFDQRS\RYHUEORZHUKRXVLQJDQGVHFXUHLWWR

KRRGERG\XVLQJ[SDQKHDGPDFKLQHVFUHZVWKURXJK¿OWHURSHQLQJ),*/

 /LIWKRRGDQGDOLJQWKHSUHLQVWDOOHGPRXQWLQJVFUHZVORFDWHGRQWRSRIWKHXQLWERG\),*$ZLWKWKH

NH\KROHVRQWKH%RWWRPRI6XSSRUW)UDPH),*&6OLGHKRRGWRZDUGVWKHQDUURZHQGRINH\KROHVWRORFN

LQWRSODFH+DQGWLJKWHQHDFKRIWKHVFUHZVZLWKDVFUHZGULYHUWRVHFXUHKRRGWR%RWWRP6XSSRUW)UDPH

)XUWKHUVHFXUHERWWRPVXSSRUWIUDPHWRXQLWERG\E\RQH0[VDIHW\VFUHZ),*)SJ

+RRGLVLQWHQGHGWREHPRXQWHGWRD¿QLVKHGFHLOLQJ

CAUTION: At least two installers are

required due to the weight and size of the

hood.

!

Bottom Support Frame

(secures to top of blower housing)

Key Holes

front - facing controls

back

FIG. A

FIG. C

FIG. B

Side

Front

XP022220

A

B

Cut-Out Shaded Area

FIG. G

FRONT

BLOWER

HOUSING

FIG. L

13

Installation – Mounting the Hood

1

Top Duct Covers

Top Support Frame

Bottom Duct Covers

Bottom Support Frame

6. Remove tape securing electronics mounting bracket to hood and reposition electronics mounting bracket.

),*(,QVWDOOHOHFWULFDODQGGXFWZRUN$FDEOHORFNQRWVXSSOLHGPLJKWEHUHTXLUHGE\ORFDOFRGHV),*

(6HDOGXFWZRUNZLWKDOXPLQXPGXFWWDSH

7. Power up hood, verify all functions and check for leaks around duct tape.

 $VVHPEOH7RS'XFW&RYHUVZLWKORXYHUKROHVWRJHWKHURYHU7RS6XSSRUW)UDPHVHFXUH7RS'XFW&RYHUV

together by magnetic strips. Note: If using hood in ductless recirculating mode you must install the air

diverter plate to the Top Support Frame prior to assembling the duct covers. Turn to page 11 for more

details.

 6HFXUH7RS'XFW&RYHUVWR7RS6XSSRUW)UDPHE\XVLQJ[VFUHZVVFUHZVIRUHDFK7RS'XFW

&RYHU),*'

10. Assemble Bottom Duct Covers together over Top Duct Covers and secure together by magnetic strips.

Bottom Duct Covers should rest on top of the Hood Body.

FIG. D

Cable Lock

$ FDEOH ORFNLQJ FRQQHFWRU QRW

VXSSOLHG PLJKW EH UHTXLUHG

by local codes. Check with

local requirements and codes,

purchase and install appropriate

connector if necessary.

FIG. E

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be

properly

grounded. Turn off electrical power at service entrance before wiring.

!

FIG. F

14

www.zephyronline.com

Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed.

When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust

IURPFRRNLQJDUHGUDZQDQG¿OWHUHGE\DVHWRIRSWLRQDOFKDUFRDO¿OWHUV7KHDLULVWKHQSXUL¿HGDQGUH

circulated back within the home.

We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct

ZRUNLISRVVLEOH7KHKRRGLVPRVWHIIHFWLYHDQGHI¿FLHQWDVDQH[KDXVWKRRG2QO\ZKHQWKHH[KDXVWRSWLRQ

is not possible should you recourse to converting the hood into a recirculating hood.

:KHQFRQYHUWHGWREHDUHFLUFXODWLQJKRRGDVHWRIFKDUFRDO¿OWHUVDUHUHTXLUHGRQWRSRILWVVWDQGDUG

DOXPLQXPPHVK¿OWHUVHW2UGHUDFFRUGLQJWRLWVSDUWQXPEHUEHORZ7KHVWDQGDUGDOXPLQXPPHVK¿OWHUVDUH

LQWHQGHGWRFDSWXUHUHVLGXHIURPFRRNLQJDQGWKHRSWLRQDOFKDUFRDO¿OWHUVKHOSWRSXULI\IXPHVH[KDXVWHGIURP

cooking for recirculation.

RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED)

.LWLQFOXGHVFKDUFRDO¿OWHU¿OWHUDWWDFKPHQWFOLSDQGDLUGLYHUWHUSODWH

Hood Models Part No. Filters in pkg.

ZAZ ZRC-02AZ 2

ZLC ZRC-00LC 1

ZRM-E36DS ZRC-02RM 2

ZRM-E42DS ZRC-01RM 3

ZRE ZRC-00RE 2

1. Purchase recirculating kit per the part number above

2. Secure air diverter plate to top support frame. Open sides of air diverter plate should face left and right

to direct air through the louver holes located on the top duct cover. Run 6” ducting from top of hood and

secure to air diverter plate.

 5HPRYHPHVK¿OWHUVIURPKRRG,QVWDOOFKDUFRDO¿OWHUVDVUHIHUHQFHGZLWKWKHPDQXDOLQFOXGHGZLWK

recirculation kit.

5H,QVWDOOPHVK¿OWHUV

7XUQRQFKDUFRDO¿OWHUFKDQJHLQGLFDWRURQFRQWUROSDQHO5HIHUWRGHWDLOVRQSDJH7KH

PLFURSURFHVVRULQWKHFRQWUROVZLOOLQGLFDWHWKHQHHGWRFKDQJHWKHFKDUFRDO¿OWHUDIWHUKRXUVRI

FRQWLQXRXVXVH2UGHUUHSODFHPHQWFKDUFRDO¿OWHUVSHUWKHOLVWEHORZ

 &KDUFRDO¿OWHUVPXVWEHUHSODFHGDIWHUHYHU\KRXUVRIXVHRUDSSUR[LPDWHO\HYHU\WRPRQWKV

EDVHGRQDQDYHUDJHRIKUVRIGDLO\FRRNLQJWLPH

NOTE: For more details refer to manual included with recirculation kit.

Charcoal Filter Replacements

Hood Model Part No. Qty to Order

ZAZ Z0F-C091 2

ZLC Z0F-C092 1

ZRM-E36DS Z0F-C002 2

ZRM-E42DS Z0F-C002 3

ZRE Z0F-C002 2

'2127:$6+&+$5&2$/),/7(56&KDUFRDO¿OWHUVPD\QHHG

to be changed more often depending on cooking habits.

Installation – Ductless Recirculating

15

Lights On/Dim/Off

Display (speed level, delay off, filter clean/change)

Adjust 5 Speed Levels

Power / Delay Off

1 POWER / DELAY OFF BUTTON

Power Button Function

- Button will turn power on and off for entire hood (fan and lights).

- Hood will remember the last speed and light level it was turned off at.

(Example: Press Button to turn off hood when on fan speed 4 and high lights. Press Button

again and the hood will turn back on at speed 4 and high lights level.)

Delay Off Button Function

- With the fan on press and hold the Button for two seconds. The fan will change to speed 1 and the

5 minute delay off timer will start.

+ LEDs will illuminate and slowly blink in accordance with the time

remaining until the fan and lights automatically turn off.

- Pressing Button while Delay Off Function is enabled will turn the hood off and cancel the Delay Off

Function.

ACT Verification

- Airflow Control Technology (ACT) allows the installer to set the maximum fan CFM to align with local

codes and regulations.

- To verify the maximum fan CFM:

- With hood off, hold the Button for two seconds. If all five fan speed indicators illuminate =

default maximum CFM. If four fan speed indicators illuminate = 390 maximum CFM. If 3 fan

speed indicators illuminate = 290 maximum CFM.

2 SPEED SELECTION BUTTON

Fan Speed Decrease Button

- Press this button to decrease fan speed. 5, 4, 3, 2, 1.

- If fan is On Speed 1 and this button is pressed, fan will power Off.

Fan Speed Increase Button

- Press this button to increase fan speed. Fan On, 1, 2, 3, 4, 5.

- If hood is Off and this button is pressed, fan will turn On Speed 1.

Act Enabled Speed Selections

- When ACT is enabled, the number of fan speeds will be reduced as follows:

- 390 CFM = Maximum 4 speeds

- 290 CFM = Maximum 3 speeds

Lighted Glass Button

5

MODEL ZLC ONLY

Features & Controls - ICON Touch Controls

16

www.zephyronline.com

3 LIGHTS BUTTON

- Lights are two levels, High and Low.

- From off, press one time for High. Press again for Low. Press again to power lights off.

4 DISPLAY INDICATORS

Mesh Filter Clean Reminder (always enabled)

- After 30 hours of fan usage, the button indicator will begin to slowly blink indicating it is time to

clean the mesh filters.

- To reset: With hood off: hold the button for three seconds. All LED indicators will blink two times

confirming the 30 hour timer has been reset.

Charcoal Filter Replace Indicator (disabled by default, must be enabled if recirculating hood)

- To enable Charcoal Filter Replacement Reminder:

- With hood off, hold button and button simultaneously for two seconds. All LED indicators

will illuminate for three seconds confirming the Charcoal Filter Replace Reminder is enabled.

- To disable Charcoal Filter Replacement Reminder:

- With hood off, hold button and button simultaneously for two seconds. All LED indicators

will blink two times confirming the Charcoal Filter Replace Reminder is disabled.

- After 120 hours of fan usage the button will slowly blink indicating the charcoal filters need

replacment.

- To reset: With hood off, hold the button for two seconds. All LED indicators will blink two times

confirming the 120 hour timer has been reset.

5 LIGHTED GLASS BUTTON (MODEL ZLC ONLY)

- Press to cycle glass color from White, Blue, Amber and Off.

- Press and hold for 3 seconds to activate demo mode. While in demo mode each color will gradually

change every 10 seconds.

- Pressing to power off the LED lights will also power off the lighted glass.

Features & Controls - ICON Touch Controls

17

Maintenance – Hood and Filter Cleaning

SURFACE MAINTENANCE:

Do not use corrosive detergents, abrasive detergents or oven cleaners.

Do not use any product containing chlorine bleach or any product containing chloride.

Do not use steel wool or abrasive scrubbing pads which will scratch and damage surface.

Cleaning Stainless Steel

&OHDQSHULRGLFDOO\ZLWKZDUPVRDS\ZDWHUDQGFOHDQFRWWRQFORWKRUPLFUR¿EHUFORWK$OZD\VUXELQWKH

direction of the stainless steel grain. To remove heavier grease build up use a liquid degreaser detergent.

After cleaning use a non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster

DQGJUDLQ$OZD\VVFUXEOLJKWO\ZLWKFOHDQFRWWRQFORWKRUPLFUR¿EHUFORWKDQGEXIILQWKHGLUHFWLRQRIWKH

stainless steel grain.

Cleaning Black Stainless Steel

&OHDQSHULRGLFDOO\ZLWKZDUPVRDS\ZDWHUDQGFOHDQFRWWRQFORWKRUPLFUR¿EHUFORWK7RUHPRYHKHDYLHU

grease build up use a liquid degreaser detergent.

Due to a built-in layer of protective anti-smudge coating, do not use stainless steel polish/cleaners to buff

out black stainless steel.

Aluminum Mesh Filters

7KHDOXPLQXPPHVK¿OWHUVLQVWDOOHGE\WKHIDFWRU\DUHLQWHQGHGWR¿OWHURXWUHVLGXHDQGJUHDVHIURP

cooking. They need not be replaced on a regular basis but are required to be kept clean.

Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if

heavily soiled.

'U\¿OWHUVDQGUHLQVWDOOEHIRUHXVLQJKRRG

Removing Aluminum Mesh Filters

3XOOGRZQRQ¿OWHUODWFKWRUHOHDVH¿OWHUWDEV

3XOOGRZQRQIURQWRI¿OWHUWRUHPRYH

18

www.zephyronline.com

Troubleshooting

TROUBLESHOOTING PROCEDURES

Issue Cause What to do

After installation,

the unit doesn’t

work.

1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s

power is ON.

2. The power line and the cable locking connector

is not connecting properly.

2. Check the power connection with the unit is

connected properly.

3. The switch board or control board wirings are

disconnected.

3. Make sure the wirings at the switch board and

control board are connected properly.

4. The switch board or control board is defective. 4. Change the switch board or control board.

Light works, but

blower is not

turning.

1. The blower is defective, possibly seized. 1. Change the blower.

2. The thermally protected system detects if the

blower is too hot to operate and shuts the blower

down.

2. The blower will function properly after the

thermally protected system cool down.

3. Damaged capacitor. 3. Change the capacitor.

4. The switch board or control board is defective. 4. Change defective part.

The speed levels

of the blower

sound the same.

1. Using the wrong size or type of ducting. 1. Change the duct size to at least 6” round or

higher and change the duct type to rigid metal

UDWKHUWKDQÀH[DEOH

The unit is

vibrating.

1. The blower is not secured in place. 1. Tighten the blower in place.

2. Damaged blower wheel. 2. Replace the blower.

3. The hood is not secured in place. 3. Check the installation of the hood.

The blower is

working, but the

lights are not.

1. Defective LED bulb. 1. Change the LED bulb.

2. The LED wire connection to the control board is

disconnected.

2. Check the LED wire connection at the control

board.

3. The LED bulb connector is disconnected. 3. Check the LED bulb connector.

The unit turns on

by itself.

1. A spot light or kitchen lamp is shining directly

onto the switch controls.

1. The switch controls are light sensative. A

direct light source onto the switch controls

may disrupt switch functions.

The hood is

not venting out

properly.

1. The hood might be hanging to high from the

cook top.

1. Adjust the distance between the cook top and

the bottom of the hood within 26” and 34”

range.

2. The wind from the opened windows or opened

doors in the surrounding area are affecting the

ventilation of the hood.

2. Close all the windows and doors to eliminate

WKHRXWVLGHZLQGÀRZ

3. Blockage in the duct opening or ductwork. 3. Remove all the blocking from the duct work or

duct opening.

4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.

5. Using the wrong size of ducting. 5. Change the ducting to at least 6” or higher.

Mesh Filter is

vibrating.

 0HVK¿OWHULVORRVH  &KDQJHWKHPHVK¿OWHU

La page est en cours de chargement...

Zephyr ZREM90ABSGG Mode d'emploi

Ce manuel convient également à

Zephyr ZREM90ABSGG Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents