Panasonic KXHNC301 Manuel utilisateur

Installation Manual

Baby Monitor

Additional camera

Model No. KX-HNC301

Thank you for purchasing a Panasonic product.

This unit is an additional camera compatible with the following

series of Panasonic Baby Monitor:

– KX-HN3001/KX-HN3051/KX-HN4001/KX-HN4101/

KX-HN4102/KX-HN1032

You must register this camera with your baby monitor before

it can be used. This installation manual describes only the steps

needed to register and begin using the camera. Please read the

baby monitor’s operating instructions for further details.

Please read this installation manual before using the unit and save it for

future reference.

For U.S.A. users

For assistance, please visit our Web site:

http://shop.panasonic.com/support for customers in the U.S.A.

For Canada users

For assistance, please visit our support page on:

www.panasonic.ca/english/support

www.panasonic.ca/french/support

(Camera Model No. KX-HNC300)

FrançaisEspañol

English

HNC301_(en_en)_0517_ver.120.pdf 1 2019/05/17 17:19:19

Accessory information

Supplied accessories

No. Accessory item/Part number Qty.

A

AC adaptor

*

1

B

Wall mounting adaptor

*

2

1

A B

For U.S.A. users:

*

1 PNWYAC300W00 (for U.S.A. users only)

*2 PNWYAC300W01 (for U.S.A. users only)

Other information

R D

esign and specifications are subject to change without notice.

R The illustrations in these instructions may vary slightly from the actual

product.

2

Introduction

HNC301_(en_en)_0517_ver.120.pdf 2 2019/05/17 17:19:19

Connections

Insert the AC adaptor plug firmly into the DC jack.

Connect the AC adaptor to the power outlet.

2

1

Note:

R U

se only the supplied AC adaptor S006AKU0500100.

R The camera unit can be placed on a flat surface. Make sure to choose

a stable location.

R The camera can also be mounted on the wall (page 10).

Note about power connections

A

C adaptor connection

R The AC adaptor must remain connected at all times. (It is normal for

the adaptor to feel warm during use.)

R The AC adaptor should be connected to a vertically oriented or

floor-mounted AC outlet. Do not connect the AC adaptor to a

ceiling-mounted AC outlet, as the weight of the adaptor may cause it

to become disconnected.

3

Installation

HNC301_(en_en)_0517_ver.120.pdf 3 2019/05/17 17:19:19

Registering a camera unit

Y

ou must register the camera unit to your monitor unit before it can be

used.

1 Monitor unit:

MMENUN a MbN: “Camera Management” a MOKN a MbN: “Add

Camera” a MOKN

R An operation guide is displayed. Press MOKN to continue.

R Complete the following step within 90 seconds.

2 Camera unit:

Press and hold M

N

for 3 seconds until the LED indicator starts

blinking.

1

M N

(Pairing)

2

LED indicator

2

1

Note:

R A

message is displayed on the monitor unit to show if the registration

was successful or not, and a beep sounds.

LED indicator

Y

ou can use the LED indicator to confirm the camera unit’s status.

LED indicator Status

Off No power

Green, lit Normal operation

Green, blinking slowly Registration mode

Green, blinking quickly Device malfunction

4

Installation

HNC301_(en_en)_0517_ver.120.pdf 4 2019/05/17 17:19:19

Graphical symbols for use on equipment

a

nd their descriptions

Symbol Explanation Symbol Explanation

Alternating current

(

A.C.)

Class P

equipment

(equipment in which

protection against

electric shock relies on

Double Insulation or

Reinforced Insulation)

Direct current (D.C.)

For indoor use only Stand-by (power)

About this system

R This system is not designed to provide complete protection from property loss.

To the maximum extent permitted by applicable law, Panasonic will not be

held responsible for any damage incurred as a result of property loss.

R This product should not be used as substitute for a medical or caregiver’s

supervision. It is the caregiver’s responsibility to stay close enough to handle

any eve

ntuality.

R The system’s wireless features are subject to interference, therefore

functionality in all situations cannot be guaranteed.

Panasonic will not be held responsible for injury or damage to property that

occurs in the event of wireless communication error or failure.

R If a power failure occurs or the power is disconnected, the temperature will not

be accurate for up to an hour.

5

Important Information

HNC301_(en_en)_0517_ver.120.pdf 5 2019/05/17 17:19:19

For your safety

T

o prevent severe injury and loss of life/property, read this section

carefully before using the product to ensure proper and safe operation of

your product.

WARNING

Power connection

R C

ompletely insert the AC adaptor/power plug into the power outlet.

Failure to do so may cause electric shock and/or excessive heat

resulting in a fire.

R Regularly remove any dust, etc. from the AC adaptor/power plug by

pulling it from the power outlet, then wiping with a dry cloth.

Accumulated dust may cause an insulation defect from moisture, etc.

resulting in a fire.

R Unplug the product from power outlets if it emits smoke, an abnormal

smell, or makes an unusual noise. These conditions can cause fire or

electric shock. Confirm that smoke has stopped emitting and contact

us.

For U.S.A. users

http://shop.panasonic.com/support

For Canada users

www.panasonic.ca/english/support

www.panasonic.ca/french/support

R Unplug from power outlets and never touch the inside of the product if

its casing has been broken open. Danger of electric shock exists.

R Never touch the plug with wet hands. Danger of electric shock exists.

Installation

R T

o prevent the risk of fire or electrical shock, do not expose the

product to rain or any type of moisture.

R Do not place or use this product near automatically controlled devices

such as automatic doors and fire alarms. Radio waves emitted from

6

Important Information

HNC301_(en_en)_0517_ver.120.pdf 6 2019/05/17 17:19:19

this product may cause such devices to malfunction resulting in an

accident.

R WARNING:

Strangulation Hazard: Children have STRANGLED in cords.

Keep this cord out of the reach of children (more than 1 m (3 feet)

away).

R Do not allow the AC adaptor to be excessively pulled, bent or placed

under heavy objects.

R Keep small parts, such as screws, out of the reach of children. There

is a risk of swallowing. In the event they are swallowed, seek medical

advice immediately.

Operating safeguards

R U

nplug the product from power outlets before cleaning. Do not use

liquid or aerosol cleaners.

R Do not disassemble the product.

R Never put metal objects inside the product. If metal objects enter the

product, turn off the circuit breaker and contact an authorized service

center.

Medical

R C

onsult the manufacturer of any personal medical devices, such as

pacemakers or hearing aids, to determine if they are adequately

shielded from external RF (radio frequency) energy. DECT features

7

Important Information

HNC301_(en_en)_0517_ver.120.pdf 7 2019/05/17 17:19:20

operate between 1.92 GHz and 1.93 GHz with a peak transmission

power of 115 mW (max.).

R Do not use the product in health care facilities if any regulations

posted in the area instruct you not to do so. Hospitals or health care

facilities may be using equipment that could be sensitive to external

RF energy.

CAUTION

Installation and location

R Never install wiring during a lightning storm.

R The AC adaptor is used as the main disconnect device. Ensure that the AC

outlet is installed near the product and is easily accessible.

R Mount the product on the stable location where the camera unit can be

adequately supported when installing.

R Do not mount the product on soft material. It may fall down, break or cause

injury.

R Do

not mount the product on the following materials: gypsum board, ALC

(autoclaved lightweight cellular concrete), concrete block, plywood less than

25 mm (1 inch) thick, etc.

Preventing accidents and injuries

R D

o not put your ear(s) near the speaker, as loud sounds emitted from

the speaker may cause hearing impairment.

Important safety instructions

W

hen using your product, basic safety precautions should always be

followed to reduce the risk of fire, electric shock, and injury to persons,

including the following:

1. Do not use this product near water for example, near a bathtub,

washbowl, kitchen sink, or laundry tub, in a wet basement or near a

swimming pool.

2. Use only the power cord indicated in this manual.

8

Important Information

HNC301_(en_en)_0517_ver.120.pdf 8 2019/05/17 17:19:20

SAVE THESE INSTRUCTIONS

Other information

Routine care

R W

ipe the outer surface of the product with a soft moist cloth.

R Do not use benzine, thinner, or any abrasive powder.

Camera image quality

R Camera images may have the following characteristics.

– Colors in images may differ from the actual colors.

– Faces or objects may appear dark when there is light behind the

subject (i.e., backlighting).

– Image quality may be reduced in dark locations.

When the subject is lit by sunlight or halogen lights, black areas of the

i

mage may appear purplish. This is not a malfunction.

Notice (ONLY FOR U.S.A.):

LThis product is designed for use in the United States of

America. Sale or use

of this product in other countries may violate local laws.

LCet appareil est conçu pour être utilisé aux États-Unis d’Amérique. La vente

ou l’emploi de cet appareil dans certains autres pays peut constituer une

infraction à la législation locale.

LEste producto está diseñado para usarse en los Estados Unidos de América.

La venta o el empleo de este producto en ciertos países puede constituir

violación de la legislación local.

L

Lࡇࡢ〇ရࡣࠊ᪥ᮏᅜእ࡛ࡢ౑⏝ࢆ┠ⓗ࡜ࡋ࡚タィࡉࢀ࡚࠾ࡾࠊ᪥ᮏᅜෆ࡛ࡢ

౑⏝ࡣἲᚊ㐪཯࡜࡞ࡾࡲࡍࠋᚑࡗ࡚ࠊᙜ♫࡛ࡣ᪥ᮏᅜෆ࡟࠾࠸࡚ࡣཎ๎࡜ࡋ

࡚ಟ⌮࡞࡝ࡢࢧ࣮ࣅࢫࡣ⮴ࡋ࠿ࡡࡲࡍࠋ

9

Important Information

HNC301_(en_en)_0517_ver.120.pdf 9 2019/05/17 17:19:20

Wall mounting

R A

ttach the wall mounting adaptor to the camera unit after making the

connections (page 3).

R Only use the supplied screw that is attached to the camera base when

attaching the wall mounting adaptor to the camera unit. Do not use

user supplied screws. This may cause the camera unit to become

loose from the wall mounting adaptor.

R Mount the camera unit on the stable location where the unit can be

adequately supported when installing.

R Use a string or wire to prevent the camera unit from falling and

causing injury if the camera unit comes off from the wall.

R Do not mount the wall mounting adaptor to a ceiling.

R Do not mount the camera unit on a soft material. It may fall down,

break or cause injury.

R Do not mount the camera unit on the following places: plaster board,

ALC (autoclaved lightweight cellular concrete), concrete block,

plywood less than 25 mm (1 inch) thick, etc.

1 Remove the screw and then remove the camera base from the

camera unit.

1

Supplied screw

10

Wall mounting

HNC301_(en_en)_0517_ver.120.pdf 10 2019/05/17 17:19:20

2 A

ttach the wall mounting adaptor to the camera unit.

3 D

rive the supplied screw into the camera unit.

1

Supplied screw

4 D

rive the screws (not supplied) into the wall.

2

Longer than 20 mm (

2

5

/32 inches)

3

Space 1.3 mm (

1

/3

2 inches)

2 3

11

Wall mounting

HNC301_(en_en)_0517_ver.120.pdf 11 2019/05/17 17:19:20

Note:

R Use the following template when determining the location of the

screw holes.

(1 / inches)

31 mm

7

3

2

5 M

ount the camera unit to the wall.

4

Screws

5

31 mm (1

7

/32 inches)

4

5

6 A

djust the angle of the camera unit by using MFN, MEN, MDN, or MCN on

the monitor unit.

12

Wall mounting

HNC301_(en_en)_0517_ver.120.pdf 12 2019/05/17 17:19:20

Specifications

R S

tandards

DECT (Digital Enhanced

Cordless Telecommunications)

R Frequency range

DECT: 1.92 GHz – 1.93 GHz

R RF transmission power

DECT: 115 mW (max.)

R Power source

Input: 100 – 240 V AC,

50/60 Hz

Output: 5.0 V DC, 1,000 mA

R Power consumption

Normal operation: 2.8 W

Night vision mode: 4.2 W

Sleep mode: 2.1 W

R Operating conditions

0 °C – 40 °C (32 °F – 104 °F)

up to 90 % relative humidity

(non-condensing)

R Transmitting range

Up to 457.5 m (1,500 feet)

*1

R Image sensor

0.3 megapixel CMOS

R Minimum illuminance

required

0 lx

*2

R Focal length

Fixed (0.4 m (1.3 feet) – infinity)

R Angular field of view (camera

angle)

Horizontal: approx. 37°

Vertical: approx. 28°

R Motion detection method

Visual sensor

R Detection range

Motion sensor:

Horizontal: approx. 37°

Vertical: approx. 28°

R Adjustable mounting angles

Horizontal: ±136°

Vertical: facing forward - facing

down approx. +0° to -44°

(movable range with the pan/tilt)

R Dimensions (height ´ width ´

depth)

Approx. 123 mm ´ 77 mm ´

69 mm (4

13

/16 inches ´

3

1

/16 inches ´ 2

11

/16 inches)

R Mass (weight)

Approx. 224 g (0.49 lb)

*1 When used in the direction of

maximum radiation, in the line

of sight, and with no

interference.

*2 The infrared LEDs that

surround the camera lens will

illuminate in low-light

conditions.

13

Appendix

HNC301_(en_en)_0517_ver.120.pdf 13 2019/05/17 17:19:20

FCC and other information (for U.S.A.

u

sers)

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may

cause undesired operation.

Privacy of communications may not be ensured when using this device.

CAUTION:

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this

device.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

14

Appendix

HNC301_(en_en)_0517_ver.120.pdf 14 2019/05/17 17:19:20

Some devices operate at frequencies that may cause interference to

nearby TVs and VCRs. To minimize or prevent such interference, this

device should not be placed near or on top of a TV or VCR. If

interference is experienced, move this device further away from the TV

or VCR. This will often reduce or eliminate interference.

FCC RF Exposure Warning:

R This product complies with FCC radiation exposure limits set forth for

an uncontrolled environment.

R To comply with FCC RF exposure requirements, the device must be

installed and operated 20 cm (8 inches) or more between the product

and all person’s body.

R This product may not be collocated or operated in conjunction with

any other antenna or transmitter.

Notice:

R FCC ID can be found on the rear of the unit.

Other notices and information (for

Canada users)

NOTICE:

This device complies with Innovation, Science and Economic Development

Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation

of the device.

RF Exposure Warning:

R This product complies with ISED radiation exposure limits set forth for an

uncontrolled environment.

R To comply with ISED RF exposure requirements, the device must be installed

and operated 20 cm (8 inches) or more between product and all person’s

body.

15

Appendix

HNC301_(en_en)_0517_ver.120.pdf 15 2019/05/17 17:19:20

Customer services (for U.S.A. users)

Accessories!

http://shop.panasonic.com/support

Customer Services Directory

Shop

for all your Panasonic gear

Go to

Get everything you need to get the most out of

your Panasonic products

Accessories & Parts for your Camera, Phone, A/V

products, TV, Computers & Networking, Personal

Care, Home Appliances, Headphones, Ba!eries,

Backup Chargers & more…

For Product Informa"on, Opera"ng Assistance,

Parts, Owner’s Manuals, Dealer and Service info

go to http://shop.panasonic.com/support

For the hearing or speech impaired TTY: 1- 877-833-8855

As of June 2015

16

Appendix

HNC301_(en_en)_0517_ver.120.pdf 16 2019/05/17 17:19:20

Limited Warranty (ONLY FOR U.S.A.)

Limited Warranty Coverage (For USA Only)

Labor

One (1) Year

Parts

One (1) Year

To submit a new repair request and for quick repair status visit our Web Site at

http://shop.panasonic.com/support

Panasonic Products Limited Warranty

Online Repair Request

Mail-In Service--Online Repair Request

If your product does not work properly because of a defect in materials or workmanship,

Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length

of the period indicated on the chart below, which starts with the date of original purchase

(“warranty period”), at its option either (a) repair your product with new or refurbished parts,

(b) replace it with a new or a refurbished equivalent value product, or (c) refund your

purchase price. The decision to repair, replace or refund will be made by the warrantor.

During the “Labor” warranty period there will be no charge for labor. During the “Parts”

warranty period, there will be no charge for parts. This Limited Warranty excludes both

parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).

This warranty only applies to products purchased and serviced in the United States.

This warranty is extended only to the original purchaser of a new product which was

not sold “as is”.

Home Network System Products

microSD card (Included model only)

90 days N/A

When shipping the unit, carefully pack, include all supplied accessories listed in the

Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box.

When shipping Lithium Ion batteries please visit our Web Site at

http://shop.panasonic.com/support as Panasonic is committed to providing the most up to

date information. Include a letter detailing the complaint, a return address and provide a

daytime phone number where you can be reached. A valid registered receipt is required

under the Limited Warranty.

IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL

BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING

DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL

BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF

OF PURCHASE.

Product or Part Name

17

Appendix

HNC301_(en_en)_0517_ver.120.pdf 17 2019/05/17 17:19:20

Limited Warranty Limits and Exclusions

(As examples, this excludes damages for lost time, travel to and from the servicer,

loss of or damage to media or images, data or other memory or recorded content.

The items listed are not exclusive, but for illustration only.)

This warranty ONLY COVERS failures due to defects in materials or workmanship,

and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty

ALSO DOES NOT COVER damages which occurred in shipment, or failures which

are caused by products not supplied by the warrantor, or failures which result from

accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty

installation, set-up adjustments, misadjustment of consumer controls, improper

maintenance, power line surge, lightning damage, modification, introduction of sand,

humidity or liquids, commercial use such as hotel, office, restaurant, or other business

or rental use of the product, or service by anyone other than a Factory Service Center

or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER

“LIMITED WARRANTY COVERAGE”.

THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT

OF ANY BREACH OF THIS WARRANTY.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF

MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,

ARE YOUR RESPONSIBILITY.

Some states do not allow the exclusion or limitation of incidental or consequential damages,

or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary

from state to state. If a problem with this product develops during or after the warranty period,

you may contact your dealer or Service Center. If the problem is not handled to your

satisfaction, then write to:

Consumer Affairs Department

Panasonic Corporation of North America

661 Independence Pkwy

Chesapeake, VA 23320

As of June 2015

18

Appendix

HNC301_(en_en)_0517_ver.120.pdf 18 2019/05/17 17:19:20

Warranty (for Canada users)

Dry cell batteries are also excluded from coverage under this warranty. Rechargeable batteries are

warranted for ninety (90) days from date of original purchase.

This warranty ON

LY COVERS failures due to defects in materials or workmanship, and DOES NOT

COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages

which occurred in shipment, or failures which are caused by products not supplied by Panasonic

Canada Inc., or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication,

alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper

maintenance, improper batteries, power line surge, lightning damage, modification, introduction of sand,

humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the

product, or service by anyone other than a Authorized Servicer, or damage that is attributable to acts of

God.

THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY

SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS

PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.

(As examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer,

loss of or damage to media or images, data or other memory or recorded content. This list of items is not

exhaustive, but for illustration only.)

Home Network System Products – One (1) year

microSD card (Included model only) – One (1) year

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3

PANASONIC PRODUCT - LIMITED WARRANTY

Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship

under normal use and for a period as stated below from the date of original purchase agrees to, at its

option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a

refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace

or refund will be made by Panasonic Canada Inc.

This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift,

of a Panasonic brand product mentioned above sold by an authorized Panasonic dealer in Canada

and purchased and used in Canada, which product was not sold “as is”, and which product was

delivered to you in new condition in the original packaging.

IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE

RECEIPT OR OTHER PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID

AND PLACE OF PURCHASE IS REQUIRED

LIMITATIONS AND EXCLUSIONS

EXCHANGE PROGRAM

19

Appendix

HNC301_(en_en)_0517_ver.120.pdf 19 2019/05/17 17:19:20

www.panasonic.ca/english/support

In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or

consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions

may not be applicable. This warranty gives you specific legal rights and you may have other rights which

vary depending on your province or territory.

For product information and operation assistance, please visit our Support page:

CONTACT INFORMATION

For defective product exchange within the warranty period, please contact the original dealer.

20

Appendix

HNC301_(en_en)_0517_ver.120.pdf 20 2019/05/17 17:19:20

La page charge ...

Panasonic KXHNC301 Manuel utilisateur

Ce manuel convient également à

Panasonic KXHNC301 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents