Haier HM1630 Manuel utilisateur

Catégorie
Coffres de rangement
Taper
Manuel utilisateur

Ce manuel convient également à

Over the Range Microwave Oven Installation
Installation du Four À Micro-Ondes
À Hotte Intégrée
Instalación del Horno Microondas
Quality
t
Innovation
t
Style
Installation Manual
Model # HM1630
Manual del Usuario
Para Modelo de # HM1630
Guide de l’Utilisateur
Modéle# HM1630
Part # MW-7777-01
1
English
TABLE OF CONTENTS
PAGE
SAFETY PRECAUTIONS ............................................................................. 2
Electrical Requirements .............................................................................. 3
Before Using Your Microwave Oven ........................................................... 4
Hood Exhaust .........................................................................................5-6
Damage – Shipment/Installation ................................................................. 7
OVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS
WHAT DO I NEED TO HAVE TO INSTALL THE MICROWAVE OVEN? .........7-8
Parts Included .......................................................................................... 7
Tools You Will Need ................................................................................ 8
Mounting Space ....................................................................................... 8
WHAT DO I NEED TO DO BEFORE I INSTALL THE MICROWAVE OVEN? .9-11
PLACEMENT OF THE MOUNTING PLATE ...............................................9-11
Removing the Mounting Plate .............................................................. 9
Finding the Wall Studs ....................................................................... 9
Determining Wall Plate Location ....................................................... 10
Aligning the Wall Plate ..................................................................... 11
INSTALLATION TYPES .........................................................................13-21
OUTSIDE TOP EXHAUST ......................................................................13-16
Attach Mounting Plate to Wall .......................................................... 13
Preparation of Top Cabinet .............................................................. 14
Adapting Microwave Blower for Outside Top Exhaust ......................14-15
Checking for Proper Damper Operation .............................................. 15
Mount the Microwave Oven ..........................................................15-16
Adjust the Exhaust Adaptor ................................................................ 16
Connecting Ductwork ........................................................................ 16
OUTSIDE BACK EXHAUST ...................................................................17-21
Preparing Rear Wall for Outside Back Exhaust ................................... 17
Remove Blower Plate ......................................................................... 17
Attach Mounting Plate to Wall ........................................................... 18
Preparation of Top Cabinet .............................................................. 18
Adapting Microwave Blower for Outside Back Exhaust .....................19-20
Mount the Microwave Oven ......................................................... 20-21
RECIRCULATING ................................................................................22-24
Attach Mounting Plate to Wall ........................................................... 22
Preparation of Top Cabinet .............................................................. 23
Check Blower Plate ........................................................................... 23
Mount the Microwave Oven ......................................................... 23-24
Installing or Change the Charcoal Filter ............................................. 24
Thank you for using our Haier product.
This easy-to-use manual will guide you
in getting the best performance from
your Haier Microwave Oven.
Remember to record the model and
serial number. They are on a label in
the Microwave Oven.
Model number
Serial number
Date of purchase
English
2
SAFETY PRECAUTIONS
Warning! – To reduce the risk of fire, electric shock, or injury to
persons, always exercise basic safety precautions, including the
following:
1. Read all instructions before using the appliance.
2. This product requires a three-prong grounded outlet. The installer must
perform a ground continuity check on the power outlet box before beginning
the installation to insure that the outlet box is properly grounded. If not
properly grounded, or if the outlet box does not meet electrical requirements
noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be
employed to correct any deficiencies.
3. For personal safety, remove house fuse or open circuit breaker before
beginning installation to avoid severe or fatal shock injury.
4. For personal safety, the mounting surface must be capable of supporting the
cabinet load, in addition to the added weight of this 63–85 pound (28.5–
38.5 kg) product, plus additional oven loads of up to 50 pounds (22.7 kg)
or a total weight of 113–135 pounds (51.3–61.2 kg).
5. For personal safety, this product cannot be installed in cabinet arrangements
such as an island or a peninsula. It must be mounted to BOTH a top cabinet
AND a wall.
6. For easier installation and personal safety, it is recommended that two people
install this product.
7. For personal safety, this appliance must be properly grounded to avoid
severe or fatal shock.
8. The power cord of this appliance is equipped with a three-prong (grounding
plug which mates with a standard three-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard from this appliance.
9. You should have the wall receptacle and circuit checked by a qualified
electrician to make sure the receptacle is properly grounded. Where a
standard two-prong wall receptacle is encountered, it is very important to have
it replaced with a properly grounded three-prong wall receptacle, installed by
a qualified electrician.
10. Do not, under any circumstances, cut, deform or remove any of the prongs
from the power cord. Do not use with an extension cord.
Staple your receipt to your manual.
You will need it to obtain warranty service.
3
English
ELECTRICAL REQUIREMENTS
Product rating is 120 volts AC, 60 Hertz and 1550 watts. This product must be
connected to a supply circuit of the proper voltage and frequency.
Wire size must conform to the requirements of the National Electrical Code or
the prevailing local code for this kilowatt rating. The power supply cord and plug
should be brought to a separate 15 to 20 ampere branch circuit single grounded
outlet. The outlet box should be located in the cabinet above the microwave
oven. The outlet box and supply circuit should be installed by a qualified
electrician and conform to the National Electrical Code or the prevailing local
code.
4
English
BEFORE USING YOUR MICROWAVE OVEN
YOU CAN BE SERIOUSLY INJURED
IF YOU DO NOT FOLLOW
INSTRUCTIONS IMMEDIATELY.
DANGER
WARNING
YOU CAN SERIOUSLY INJURED IF YOU
DO NOT FOLLOW INSTRUCTIONS.
All safety messages will tell you what the potential hazard is,
how to reduce the chance of injury and what can happen
if the instructions are not followed.
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS
Doing so will:
tNBLFJOTUBMMBUJPOFBTJFS
tIFMQZPVJOUIFGVUVSFJGZPVIBWFRVFTUJPOT
tIFMQJGZPVIBWFBOFMFDUSJDBMJOTQFDUJPO
Call your dealer when you have questions or need service. When you call, you
will need the microwave model and serial numbers.
This is the safety alert symbol.
This symbol alerts you to potential hazards that may seriously injure you
and others.
All safety messages follow the safety alert symbol and either the word
“DANGER” or “WARNING”
English
5
English
HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 7.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart describes an example of one possible ductwork installation.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom
corners of the damper will have to be cut to fit, using the tin snips, in order
to allow free movement of the damper.
NOTE: For back exhaust, care should be taken to align exhaust with space
between studs, or wall should be prepared at the time it is constructed by
leaving enough space between the wall studs to accommodate exhaust.
DUCT PIECES EQUIVALENT NUMBER
LENGTH X USED =
EQUIVALENT
LENGTH
Roof Cap 24 Ft. (7.3m) x (1) = 24 Ft. (7.3m)
12Ft. (3.6m)
Straight Duct
(6”/15.2cm
Round)
12 Ft. (3.6m) x (1) = 12 Ft. (3.6m)
Rectangular-to-
Round Transition
Adaptor*
5 Ft. (1.5m) x (1) = 5 Ft. (1.5m)
Equivalent lengths of duct pieces are based on actual tests and reflect
requirements for good venting performance with any vent hood.
TOTAL LENGTH:
41 Ft. (12.5 m)
DUCT PIECES EQUIVALENT NUMBER
LENGTH X USED =
EQUIVALENT
LENGTH
Wall Cap 40 Ft. (12.2m) x (1) = 40 Ft. (12.2m)
3 Ft.
Straight Duct
(31⁄4”x10”/8.2
x 25.4cm
Rectangular)
3 Ft. (0.9m) x (1) = 3 Ft. (0.9m)
90° Elbow 10 Ft. (3m) x (2) = 20 Ft. (3m)
Equivalent lengths of duct pieces are based on actual tests and reflect
requirements for good venting performance with any vent hood.
TOTAL LENGTH:
63 Ft. (19.2 m)
English
6
English
NOTE: If you need to install ducts, note that the total duct length of 31⁄4” x 10” (8.2
x 25.4 cm) rectangular or 6” (15.2 cm) diameter round duct should not exceed 120
equivalent feet (36.5 m).
Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE:
It is important that venting be installed using the most direct route and with as few elbows as
possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure
dampers swing freely and nothing is blocking the ducts.
DUCT PIECES EQUIVALENT NUMBER
LENGTH X USED =
EQUIVALENT
LENGTH
Rectangular-to-Round Transition
Adaptor*
5 Ft. (1.5m) x ( ) = Ft. or m
Wall Cap 40 Ft. (12.2m) x ( ) = Ft. or m
90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m
45° Elbow 5 Ft. (1.5m) x ( ) = Ft. or m
90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m
45° Elbow 5 Ft. (1.5m) x ( ) = Ft. or m
Roof Cap 24 Ft. (7.3 m) x ( ) = Ft. or m
Straight Duct 6“ (15.2 cm)
Round or 31⁄4“ x 10“ (8.2 x
25.4 cm) Rectangular
1 Ft. (0.3 m) x (1) = Ft. or m
Total Ductwork = Ft. or m
EXHAUST CONNECTION:
The hood exhaust has been designed to
mate with a standard 31⁄4” x 10” (8.2 x
25.4 cm) rectangular duct. If a round duct
is required, a rectangular-to-round transition
adaptor must be used. Do not use less than a
6” (15.2 cm) diameter duct.
MAXIMUM DUCT LENGTH:
For satisfactory air movement, the total
duct length of 31⁄4” x 10” (8.2 x 25.4 cm
rectangular or 6” (15.2 cm) diameter round
duct should not exceed 120 equivalent feet
(36.5 m).
ELBOWS, TRANSITIONS, WALL
AND ROOF CAPS, etc.,
present additional resistance to airflow and
are equivalent to a section of straight duct
which is longer than their actual physical
size. When calculating the total duct length,
add the equivalent lengths of all transitions
and adaptors plus the length of all straight
duct sections. The chart below shows you how
to calculate total equivalent ductwork length
using the approximate feet of equivalent
length of some typical ducts.
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall
should be prepared at the time it is constructed by leaving enough space between the wall studs to
accommodate exhaust.
English
7
English
DAMAGE—SHIPMENT/INSTALLATION
PARTS INCLUDED
t*GUIFVOJUJTEBNBHFEJOTIJQNFOUSFUVSOUIFVOJUUPUIFTUPSFJOXIJDIJUXBT
bought for repair or replacement.
t*GUIFVOJUJTEBNBHFECZUIFDVTUPNFSSFQBJSPSSFQMBDFNFOUJTUIF 
responsibility of the customer.
t*GUIFVOJUJTEBNBHFECZUIFJOTUBMMFSJGPUIFSUIBOUIFDVTUPNFSSFQBJSPS
replacement must be made by arrangement between customer and installer.
HARDWARE PACKET ADDITIONAL PARTS
PART QUANTITY
Wood Screws
(1⁄4“ x 2“)
2
Toggle Bolts
(and wing nuts)
(3⁄16“ x 3“)
4
Self-Aligning
Machine Screws
(1⁄4“-28 x
31⁄4“)
3
Nylon Grommet
(for metal
cabinets)
2
Power Cord
Strap (plastic)
1
You will find the installation hardware
contained in a packet with the unit. Check
to make sure you have all these parts.
NOTE: Some extra parts are included.
PART QUANTITY
Top Cabinet
Template
1
Rear Wall
Template
1
Installation
Instructions
1
Separately
Packed
Grease
Filters
2
Exhaust
Adaptor
1
I
NSTALLATION
I
NSTRUCTION
S
TOP CABINET TEMPLATE
REAR WALL TEMPLATE
English
8
English
TOOLS AND MATERIALS NEEDED
MOUNTING SPACE
# 1 Phillips screwdriver
Pencil
Ruler or tape measure and
straight edge
Carpenter square
(optional)
Tin snips (for cutting
damper, if required)
Hammer (optional)
Stud nder or
Filler blocks or scrap
wood pieces, if needed
for top cabinet spacing
(used on recessed bottom
cabinet installations only)
Gloves
Saw (saber, hole or keyhole)
Level
Duct and masking tape
Scissors
Electric drill with 3⁄16“, 1⁄2“ and 5⁄8“
drill bits
(to cut template, if necessary)
Safety goggles
Backsplash
66ʺ(167.6 cm)
or More from
the Floor to the
Top of the
Microwave
30
(76.2 cm)
2
“ (5.1 cm)
30
(76.2 cm)
min.
16
1
2“ (41.9 cm)
Bottom Edge of
Cabinet Needs to
be 30ʺ (76.2 cm)
or More from the
Cooking Surface
NOTES:
t5IFTQBDFCFUXFFOUIFDBCJOFUTNVTUCFiDNXJEFBOEGSFFPGPCTUSVDUJPOT
t*GZPVBSFHPJOHUPWFOUZPVSNJDSPXBWFPWFOUPUIFPVUTJEFTFF)PPE&YIBVTU
Section for exhaust duct preparation.
t8IFOJOTUBMMJOHUIFNJDSPXBWFPWFOCFOFBUITNPPUIGMBUDBCJOFUTCFDBSFGVMUP
follow the instructions on the top cabinet template for power cord clearance.
9
English
1. PLACEMENT OF THE MOUNTING PLATE
A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/
REMOVING THE MOUNTING PLATE
B. FINDING THE WALL STUDS
1. Remove the installation instructions, filters,
glass tray and the small hardware bag. Do
not remove the Styrofoam protecting the
front of the oven.
2. Fold back all 4 carton flaps fully against
carton sides. Then carefully roll the oven
and carton over onto the top side. The oven
should be resting in the Styrofoam.
3. Pull the carton up and off the oven.
4. Remove and properly discard plastic bags.
5. Remove the screws from the mounting
plate. This plate will be used as the rear
wall template and for mounting. Reinstall
the screws into the holes where they were
removed.
1. Find the studs, using one of the following
methods:
A. Stud finder – a magnetic device which
locates nails.
OR
B. Use a hammer to tap lightly across the
mounting surface to find a solid sound.
This will indicate a stud location.
2. After locating the stud(s), find the center by
probing the wall with a small nail to find the
edges of the stud. Then place a mark
halfway between the edges. The center of
any adjacent studs should be 16” (40.6 cm)
or 24” (61 cm) from this mark.
3. Draw a line down the center of the studs.
THE MICROWAVE MUST BE CONNECTED TO
AT LEAST ONE WALL STUD.
Carton
Styrofoam
Mounting
Plate
Screws
Wall
Studs
Center
10
English
C. DETERMINING WALL PLATE LOCATION UNDER YOUR
CABINET.
PLATE POSITION—BENEATH FLAT BOTTOM
CABINET
PLATE POSITION—BENEATH RECESSED
BOTTOM CABINET WITH FRONT OVERHANG
PLATE POSITION—BENEATH FRAMED RECESSED
CABINET BOTTOM
Mounting Plate Tabs
Touching the Cabinet Bottom
At least 30
ʺ
(76.2 cm),
up to 36
ʺ
(91.4 cm)
30ʺ(76.2 cm)
to Cooktop
Mounting Plate Tabs
Touching the Back Frame
Mounting Plate with
Tabs Below Cabinet
Bottom the Same
Distance as the Front
Overhang Depth
30ʺ(76.2 cm)
to Cooktop
Your cabinets may have decorative trim that interferes with the microwave installation.
Remove the decorative trim to install the microwave properly and to make it level.
THE MICROWAVE MUST BE LEVEL. Use a level to make sure the cabinet bottom is level.
If the cabinets have a front overhang only, with no back or side frame, install the
mounting plate down the same distance as the front overhang depth. This will keep
the microwave level.
Measure the inside depth of the 1. front overhang.
Draw a horizontal line on the back wall an equal distance below the cabinet 2.
bottom as the inside depth of the front overhang.
For this type of installation with front overhang only, align the mounting tabs with 3.
this horizontal line, not touching the cabinet bottom as described in Step D.
CAUTION:
Wear gloves to avoid cutting fingers on sharp edges.
11
English
D. ALIGNING THE WALL PLATE
Draw a vertical line on the wall at the center of the 30” (76.2 cm) wide space.1.
Use the mounting plate 2. as the template for the rear wall. Place the mounting
plate on the wall, making sure that the tabs are touching the bottom of the
cabinet or the level line drawn in Step C for cabinets with front overhang.
Line up the notch and centerline on the bottom of the mounting plate to the
centerline on the wall.
While holding the mounting plate with one hand, draw circles on the wall 3.
at holes A, B, C and D (see illustration above/actual plate marked with
arrows). Four holes must be used for mounting.
NOTE: If neither C nor D is in a stud, find a stud somewhere in area E and
draw a fifth circle to line up with the stud. It is important to use at least one
wood screw mounted firmly in a stud to support the weight of the microwave.
Set the mounting plate aside.
Drill holes on the circles. If there is a stud, drill a 3⁄16” hole for wood screws. 4.
For holes that don’t line up with a stud, drill a 5⁄8” hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
Draw a Vertical
Line on Wall
from Center of
Top Cabinet
Area E
Hole A
Hole B
Hole D
Hole C
Centerline
Notches
12
English
This microwave oven is designed for adaptation to the following three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)If direct-wiring microwave
NOTE: This microwave is shipped assembled for Recirculating. Select the type of
ventilation required for your installation and proceed to the section.
2. INSTALLATION TYPES (Choose A,B or C)
A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
B. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
C. RECIRCULATING (NON-VENTED DUCTLESS)
Adaptor in Place for
Outside Top Exhaust
Adaptor Must Be
Moved to the Back for
Outside Back Exhaust
On models shipped for
recirculating exhaust,
a disposable charcoal
filter is factory installed
to help remove smoke
and odors.
Page 13
Page 17
Page 22
13
English
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Adapting Microwave Blower
for Outside Top Exhaust
A4. Check Damper Operation
A5. Mount Microwave Oven
A6. Adjust Exhaust Adaptor
A7. Connect Ductwork
Attach the plate to the wall using toggle
bolts. At least one wood screw must be
used to attach the plate to a wall stud.
Remove the toggle wings from the bolts. 1.
Insert the bolts into the mounting plate 2.
through the holes designated to go into
drywall and reattach the toggle wings to
3⁄4” (19 mm) onto each bolt.
TO USE TOGGLE BOLTS:
Place the mounting plate against the 3.
wall and insert the toggle wings into the
holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw,
make sure the tabs on the mounting plate touch the
bottom of the cabinet when pushed flush against the wall
and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and thewall.
Tighten all bolts. Pull the plate away 4.
from the wall to help tighten the bolts.
A1. ATTACH THE MOUNTING PLATE TO THE WALL
IMPORTANT NOTES:
Make sure the screws for the blower motor and blower plate are securely t
tightened when they are reinstalled. This will help to prevent excessive vibration
Make sure the motor wiring has been properly routed and secured, and that t
the wires are not pinched.
A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
14
English
You need to drill holes for the top support
screws, a hole large enough for the power
cord to fit through, and a cutout large
enough for the exhaust adaptor.
t3FBEUIFJOTUSVDUJPOTPOUIF501
CABINET TEMPLATE.
t5BQFJUVOEFSOFBUIUIFUPQDBCJOFU
t%SJMMUIFIPMFTGPMMPXJOHUIFJOTUSVDUJPOT
on the TOP CABINET TEMPLATE.
CAUTION:
Wear safety goggles when drilling holes in the cabinet bottom.
Place the microwave in its upright 1.
position,with the top of the unit facing up.
Remove the screw that holds the blower
plate to the microwave. Remove and
save the screw holding the blower motor
to the microwave.
Carefully pull out the blower unit. The 2.
wires will extend far enough to allow
you to adjust the blower unit.
Roll the blower unit 90° so that fan 3.
blade openings are facing out the top
of the microwave.
A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF
TOP CABINET
A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE
TOP EXHAUST
Blower Plate
Blower Moto
Screw
Back of
Microwave
End B
End A
Back of
Microwave
Back of
Microwave
Before Rotation After Rotation
Back of
Microwave
English
FOR EASIER INSTALLATION
AND PERSONAL SAFETY, WE
RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
15
English
4. Place the blower unit back into the
opening.
5. Secure blower unit to microwave with
the screw removed in Step 1. Make
sure the screw is tight.
6. Replace blower plate with the screw
removed in Step 1. Make sure the
screw is tight.
7. Attach the exhaust adaptor to the
top of the blower plate by sliding it
into the guides of the blower plate.
Push in securely until it is in the
locking tabs. Take care to assure
that the damper hinge is installed so
that the damper swings freely.
t.BLFTVSFUBQFTFDVSJOHEBNQFSJT
removed and damper pivots easily
before mounting microwave.
t:PVXJMMOFFEUPNBLFBEKVTUNFOUT
to assure proper alignment with your
house exhaust duct after the microwave
is installed.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If your cabinet is metal, use the
nylon grommet around the power cord
hole to prevent cutting of the cord.
NOTE: We recommend using filler
blocks if the cabinet front hangs below
the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from
overtightening screws.
A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE
TOP EXHAUST
A4. CHECK FOR PROPER DAMPER OPERATION
A5. MOUNT THE MICROWAVE OVEN
Back of
Microwave
Back of
Microwave
Guide
Adaptor
Locking Tab
Exhaust Adaptor
Blower Plate
Damper
Back of
Microwave
Back of
Microwave
AFTER: Fan Blade
Openings Facing Top
English
16
English
Lift microwave, tilt it forward, and hook slots 1.
at back bottom edge onto four lower tabs of
mounting plate.
Rotate front of oven up against cabinet 2.
bottom.
Insert a self-aligning screw through top 3.
center cabinet hole. Temporarily secure
the oven by turning the screw at least two
full turns after the threads have engaged.
(It will be completely tightened later.) Be
sure to keep power cord tight. Be careful
not to pinch the cord, especially when
mounting flush to bottom of cabinet.
Attach the microwave oven to the top cabinet.4.
Insert 2 self-aligning screws through outer 5.
top cabinet holes. Turn two full turns on
each screw.
Tighten center screw completely.6.
Open the top cabinet and adjust the exhaust
adaptor to connect to the house duct.
Extend the house duct down to connect 1.
to the exhaust adaptor.
Seal exhaust duct joints using duct tape.2.
7. Tighten the outer two screws to the top of the microwave oven. (While tightening
screws, hold the microwave oven in place against the wall and the top cabinet.)
8. Install grease filters. See the Owner’s Manual packed with the microwave.
A5. MOUNT THE MICROWAVE OVEN
A6. ADJUST THE EXHAUST ADAPTOR
A7. CONNECTING DUCTWORK
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Microwave Oven Top
Equivalent
to Depth
of Cabinet
Recess
Self-Aligning Screw
Back of
Microwave
For Front-to-Back or
Side-to-Side Adjustment,
Slide the Exhaust Adaptor
as Needed
Blower Plate
Damper
House Duct
NOTE: When mounting the
microwave oven, thread power
cord through hole in bottom
of top cabinet. Keep it tight
throughout Steps 1–3. Do
not pinch cord or lift oven by
pulling cord.
1
2
5
6
English
17
English
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
You need to cut an opening in the rear
wall for outside exhaust.
Read the instructions on the REAR t
WALL TEMPLATE.
Tape it to the rear wall, lining up with t
the holes previously drilled for holes A
and B in the wall plate.
Cut the opening, following the t
instructions of the REAR WALL
TEMPLATE.
Remove and save the screw that holds the
blower plate to the microwave. Lift off the
blower plate.
B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST
B2. REMOVE BLOWER PLATE
B. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
Back of
Microwave
Blower Plate
IMPORTANT NOTES:
Make sure the screws for the blower motor and blower plate are securely t
tightened when they are reinstalled. This will help to prevent excessive vibration
Make sure the motor wiring has been properly routed and secured, and that t
the wires are not pinched.
English
18
English
Attach the plate to the wall using toggle
bolts. At least one wood screw must be
used to attach the plate to a wall stud.
Remove the toggle wings from the bolts. 1.
Insert the bolts into the mounting plate 2.
through the holes designated to go into
drywall and reattach the toggle wings to
3⁄4” (19 mm) onto each bolt.
TO USE TOGGLE BOLTS:
Place the mounting plate against the 3.
wall and insert the toggle wings into the
holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw,
make sure the tabs on the mounting plate touch the
bottom of the cabinet when pushed flush against the wall
and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and thewall.
Tighten all bolts. Pull the plate away 4.
from the wall to help tighten the bolts.
B3. ATTACH THE MOUNTING PLATE TO THE WALL
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
You need to drill holes for the top support
screws, a hole large enough for the power
cord to fit through.
Read the instructions on the TOP t
CABINET TEMPLATE.
Tape it underneath the top cabinet.t
Drill the holes, following the instructions t
on the TOP CABINET TEMPLATE.
B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF
TOP CABINET
CAUTION:
Wear safety goggles when drilling holes in the cabinet bottom.
English
B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK
EXHAUST
Remove and save screw that holds 1.
blower motor to microwave.
Carefully pull out the blower unit. The 2.
wires will extend far enough to
allow you to adjust the blower unit.
Roll the blower unit 90° 3.
5. Gently remove the wires from the
grooves. Reroute the wires through
grooves on other side of the blower unit.
7. Place the blower unit back into the
opening.
CAUTION: Do not pull or stretch the
blower unit wiring. Make sure the wires
are not pinched, and that they are
properly secured.
NOTE: The blower unit exhaust
openings should match exhaust
openings on rear of microwave oven.
8. Secure the blower unit to the
microwave with the original screw.
9. Replace the blower plate in the
same position as before with the
screw. Make sure the screw is tight.
4. Rotate blower unit counterclockwise 180°.
6. Roll the blower unit 90° so that fan blade
openings are facing out the back of the
microwave.
Back of
Microwave
Blower Motor
Blower Motor
Screw
Blower Plate
Blower Motor
Screw
Back of
Microwave
End B
End A
Forward
Openings Facing
Before: Fan Blade
Back of
Microwave
Before Rotation After Rotation
Back of
Microwave
Before Rotation After Rotation
Back of
Microwave
Back of
Microwave
Before Rerouting After Rerouting
Wires Routed Through Right Side
Wires Routed Through Left Side
Before Rolling After Rolling
Back of
Microwave
Back of
Microwave
AFTER: Fan Blade
Openings Facing Back
End A
End B
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Haier HM1630 Manuel utilisateur

Catégorie
Coffres de rangement
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues