Haier HMV1630HBSA Manuel utilisateur

Over the Range Microwave Oven Installation

Installation du Four À Micro-Ondes

À Hotte Intégrée

Instalación del Horno Microondas

Quality

t

Innovation

t

Style

Installation Manual

Model # HM1630

Manual del Usuario

Para Modelo de # HM1630

Guide de l’Utilisateur

Modéle# HM1630

Part # MW-7777-01

1

English

TABLE OF CONTENTS

PAGE

SAFETY PRECAUTIONS ............................................................................. 2

Electrical Requirements .............................................................................. 3

Before Using Your Microwave Oven ........................................................... 4

Hood Exhaust .........................................................................................5-6

Damage – Shipment/Installation ................................................................. 7

OVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS

WHAT DO I NEED TO HAVE TO INSTALL THE MICROWAVE OVEN? .........7-8

Parts Included .......................................................................................... 7

Tools You Will Need ................................................................................ 8

Mounting Space ....................................................................................... 8

WHAT DO I NEED TO DO BEFORE I INSTALL THE MICROWAVE OVEN? .9-11

PLACEMENT OF THE MOUNTING PLATE ...............................................9-11

Removing the Mounting Plate .............................................................. 9

Finding the Wall Studs ....................................................................... 9

Determining Wall Plate Location ....................................................... 10

Aligning the Wall Plate ..................................................................... 11

INSTALLATION TYPES .........................................................................13-21

OUTSIDE TOP EXHAUST ......................................................................13-16

Attach Mounting Plate to Wall .......................................................... 13

Preparation of Top Cabinet .............................................................. 14

Adapting Microwave Blower for Outside Top Exhaust ......................14-15

Checking for Proper Damper Operation .............................................. 15

Mount the Microwave Oven ..........................................................15-16

Adjust the Exhaust Adaptor ................................................................ 16

Connecting Ductwork ........................................................................ 16

OUTSIDE BACK EXHAUST ...................................................................17-21

Preparing Rear Wall for Outside Back Exhaust ................................... 17

Remove Blower Plate ......................................................................... 17

Attach Mounting Plate to Wall ........................................................... 18

Preparation of Top Cabinet .............................................................. 18

Adapting Microwave Blower for Outside Back Exhaust .....................19-20

Mount the Microwave Oven ......................................................... 20-21

RECIRCULATING ................................................................................22-24

Attach Mounting Plate to Wall ........................................................... 22

Preparation of Top Cabinet .............................................................. 23

Check Blower Plate ........................................................................... 23

Mount the Microwave Oven ......................................................... 23-24

Installing or Change the Charcoal Filter ............................................. 24

Thank you for using our Haier product.

This easy-to-use manual will guide you

in getting the best performance from

your Haier Microwave Oven.

Remember to record the model and

serial number. They are on a label in

the Microwave Oven.

Model number

Serial number

Date of purchase

English

2

SAFETY PRECAUTIONS

Warning! – To reduce the risk of fire, electric shock, or injury to

persons, always exercise basic safety precautions, including the

following:

1. Read all instructions before using the appliance.

2. This product requires a three-prong grounded outlet. The installer must

perform a ground continuity check on the power outlet box before beginning

the installation to insure that the outlet box is properly grounded. If not

properly grounded, or if the outlet box does not meet electrical requirements

noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be

employed to correct any deficiencies.

3. For personal safety, remove house fuse or open circuit breaker before

beginning installation to avoid severe or fatal shock injury.

4. For personal safety, the mounting surface must be capable of supporting the

cabinet load, in addition to the added weight of this 63–85 pound (28.5–

38.5 kg) product, plus additional oven loads of up to 50 pounds (22.7 kg)

or a total weight of 113–135 pounds (51.3–61.2 kg).

5. For personal safety, this product cannot be installed in cabinet arrangements

such as an island or a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

6. For easier installation and personal safety, it is recommended that two people

install this product.

7. For personal safety, this appliance must be properly grounded to avoid

severe or fatal shock.

8. The power cord of this appliance is equipped with a three-prong (grounding

plug which mates with a standard three-prong (grounding) wall receptacle

to minimize the possibility of electric shock hazard from this appliance.

9. You should have the wall receptacle and circuit checked by a qualified

electrician to make sure the receptacle is properly grounded. Where a

standard two-prong wall receptacle is encountered, it is very important to have

it replaced with a properly grounded three-prong wall receptacle, installed by

a qualified electrician.

10. Do not, under any circumstances, cut, deform or remove any of the prongs

from the power cord. Do not use with an extension cord.

Staple your receipt to your manual.

You will need it to obtain warranty service.

3

English

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz and 1550 watts. This product must be

connected to a supply circuit of the proper voltage and frequency.

Wire size must conform to the requirements of the National Electrical Code or

the prevailing local code for this kilowatt rating. The power supply cord and plug

should be brought to a separate 15 to 20 ampere branch circuit single grounded

outlet. The outlet box should be located in the cabinet above the microwave

oven. The outlet box and supply circuit should be installed by a qualified

electrician and conform to the National Electrical Code or the prevailing local

code.

4

English

BEFORE USING YOUR MICROWAVE OVEN

YOU CAN BE SERIOUSLY INJURED

IF YOU DO NOT FOLLOW

INSTRUCTIONS IMMEDIATELY.

DANGER

WARNING

YOU CAN SERIOUSLY INJURED IF YOU

DO NOT FOLLOW INSTRUCTIONS.

All safety messages will tell you what the potential hazard is,

how to reduce the chance of injury and what can happen

if the instructions are not followed.

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS

Doing so will:

tNBLFJOTUBMMBUJPOFBTJFS

tIFMQZPVJOUIFGVUVSFJGZPVIBWFRVFTUJPOT

tIFMQJGZPVIBWFBOFMFDUSJDBMJOTQFDUJPO

Call your dealer when you have questions or need service. When you call, you

will need the microwave model and serial numbers.

This is the safety alert symbol.

This symbol alerts you to potential hazards that may seriously injure you

and others.

All safety messages follow the safety alert symbol and either the word

“DANGER” or “WARNING”

English

5

English

HOOD EXHAUST

NOTE: Read these next two pages only if you plan to vent your exhaust to the

outside. If you plan to recirculate the air back into the room, proceed to page 7.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible ductwork installation.

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom

corners of the damper will have to be cut to fit, using the tin snips, in order

to allow free movement of the damper.

NOTE: For back exhaust, care should be taken to align exhaust with space

between studs, or wall should be prepared at the time it is constructed by

leaving enough space between the wall studs to accommodate exhaust.

DUCT PIECES EQUIVALENT NUMBER

LENGTH X USED =

EQUIVALENT

LENGTH

Roof Cap 24 Ft. (7.3m) x (1) = 24 Ft. (7.3m)

12Ft. (3.6m)

Straight Duct

(6”/15.2cm

Round)

12 Ft. (3.6m) x (1) = 12 Ft. (3.6m)

Rectangular-to-

Round Transition

Adaptor*

5 Ft. (1.5m) x (1) = 5 Ft. (1.5m)

Equivalent lengths of duct pieces are based on actual tests and reflect

requirements for good venting performance with any vent hood.

TOTAL LENGTH:

41 Ft. (12.5 m)

DUCT PIECES EQUIVALENT NUMBER

LENGTH X USED =

EQUIVALENT

LENGTH

Wall Cap 40 Ft. (12.2m) x (1) = 40 Ft. (12.2m)

3 Ft.

Straight Duct

(31⁄4”x10”/8.2

x 25.4cm

Rectangular)

3 Ft. (0.9m) x (1) = 3 Ft. (0.9m)

90° Elbow 10 Ft. (3m) x (2) = 20 Ft. (3m)

Equivalent lengths of duct pieces are based on actual tests and reflect

requirements for good venting performance with any vent hood.

TOTAL LENGTH:

63 Ft. (19.2 m)

English

6

English

NOTE: If you need to install ducts, note that the total duct length of 31⁄4” x 10” (8.2

x 25.4 cm) rectangular or 6” (15.2 cm) diameter round duct should not exceed 120

equivalent feet (36.5 m).

Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE:

It is important that venting be installed using the most direct route and with as few elbows as

possible. This ensures clear venting of exhaust and helps prevent blockages. Also, make sure

dampers swing freely and nothing is blocking the ducts.

DUCT PIECES EQUIVALENT NUMBER

LENGTH X USED =

EQUIVALENT

LENGTH

Rectangular-to-Round Transition

Adaptor*

5 Ft. (1.5m) x ( ) = Ft. or m

Wall Cap 40 Ft. (12.2m) x ( ) = Ft. or m

90° Elbow 10 Ft. (3 m) x ( ) = Ft. or m

45° Elbow 5 Ft. (1.5m) x ( ) = Ft. or m

90° Elbow 25 Ft. (7.6 m) x ( ) = Ft. or m

45° Elbow 5 Ft. (1.5m) x ( ) = Ft. or m

Roof Cap 24 Ft. (7.3 m) x ( ) = Ft. or m

Straight Duct 6“ (15.2 cm)

Round or 31⁄4“ x 10“ (8.2 x

25.4 cm) Rectangular

1 Ft. (0.3 m) x (1) = Ft. or m

Total Ductwork = Ft. or m

EXHAUST CONNECTION:

The hood exhaust has been designed to

mate with a standard 31⁄4” x 10” (8.2 x

25.4 cm) rectangular duct. If a round duct

is required, a rectangular-to-round transition

adaptor must be used. Do not use less than a

6” (15.2 cm) diameter duct.

MAXIMUM DUCT LENGTH:

For satisfactory air movement, the total

duct length of 31⁄4” x 10” (8.2 x 25.4 cm

rectangular or 6” (15.2 cm) diameter round

duct should not exceed 120 equivalent feet

(36.5 m).

ELBOWS, TRANSITIONS, WALL

AND ROOF CAPS, etc.,

present additional resistance to airflow and

are equivalent to a section of straight duct

which is longer than their actual physical

size. When calculating the total duct length,

add the equivalent lengths of all transitions

and adaptors plus the length of all straight

duct sections. The chart below shows you how

to calculate total equivalent ductwork length

using the approximate feet of equivalent

length of some typical ducts.

* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall

should be prepared at the time it is constructed by leaving enough space between the wall studs to

accommodate exhaust.

English

7

English

DAMAGE—SHIPMENT/INSTALLATION

PARTS INCLUDED

t*GUIFVOJUJTEBNBHFEJOTIJQNFOUSFUVSOUIFVOJUUPUIFTUPSFJOXIJDIJUXBT

bought for repair or replacement.

t*GUIFVOJUJTEBNBHFECZUIFDVTUPNFSSFQBJSPSSFQMBDFNFOUJTUIF 

responsibility of the customer.

t*GUIFVOJUJTEBNBHFECZUIFJOTUBMMFSJGPUIFSUIBOUIFDVTUPNFSSFQBJSPS

replacement must be made by arrangement between customer and installer.

HARDWARE PACKET ADDITIONAL PARTS

PART QUANTITY

Wood Screws

(1⁄4“ x 2“)

2

Toggle Bolts

(and wing nuts)

(3⁄16“ x 3“)

4

Self-Aligning

Machine Screws

(1⁄4“-28 x

31⁄4“)

3

Nylon Grommet

(for metal

cabinets)

2

Power Cord

Strap (plastic)

1

You will find the installation hardware

contained in a packet with the unit. Check

to make sure you have all these parts.

NOTE: Some extra parts are included.

PART QUANTITY

Top Cabinet

Template

1

Rear Wall

Template

1

Installation

Instructions

1

Separately

Packed

Grease

Filters

2

Exhaust

Adaptor

1

I

NSTALLATION

I

NSTRUCTION

S

TOP CABINET TEMPLATE

REAR WALL TEMPLATE

English

8

English

TOOLS AND MATERIALS NEEDED

MOUNTING SPACE

# 1 Phillips screwdriver

Pencil

Ruler or tape measure and

straight edge

Carpenter square

(optional)

Tin snips (for cutting

damper, if required)

Hammer (optional)

Stud nder or

Filler blocks or scrap

wood pieces, if needed

for top cabinet spacing

(used on recessed bottom

cabinet installations only)

Gloves

Saw (saber, hole or keyhole)

Level

Duct and masking tape

Scissors

Electric drill with 3⁄16“, 1⁄2“ and 5⁄8“

drill bits

(to cut template, if necessary)

Safety goggles

Backsplash

66ʺ(167.6 cm)

or More from

the Floor to the

Top of the

Microwave

30

“(76.2 cm)

2

“ (5.1 cm)

30

“

(76.2 cm)

min.

16

1

⁄2“ (41.9 cm)

Bottom Edge of

Cabinet Needs to

be 30ʺ (76.2 cm)

or More from the

Cooking Surface

NOTES:

t5IFTQBDFCFUXFFOUIFDBCJOFUTNVTUCFiDNXJEFBOEGSFFPGPCTUSVDUJPOT

t*GZPVBSFHPJOHUPWFOUZPVSNJDSPXBWFPWFOUPUIFPVUTJEFTFF)PPE&YIBVTU

Section for exhaust duct preparation.

t8IFOJOTUBMMJOHUIFNJDSPXBWFPWFOCFOFBUITNPPUIGMBUDBCJOFUTCFDBSFGVMUP

follow the instructions on the top cabinet template for power cord clearance.

9

English

1. PLACEMENT OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/

REMOVING THE MOUNTING PLATE

B. FINDING THE WALL STUDS

1. Remove the installation instructions, filters,

glass tray and the small hardware bag. Do

not remove the Styrofoam protecting the

front of the oven.

2. Fold back all 4 carton flaps fully against

carton sides. Then carefully roll the oven

and carton over onto the top side. The oven

should be resting in the Styrofoam.

3. Pull the carton up and off the oven.

4. Remove and properly discard plastic bags.

5. Remove the screws from the mounting

plate. This plate will be used as the rear

wall template and for mounting. Reinstall

the screws into the holes where they were

removed.

1. Find the studs, using one of the following

methods:

A. Stud finder – a magnetic device which

locates nails.

OR

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location.

2. After locating the stud(s), find the center by

probing the wall with a small nail to find the

edges of the stud. Then place a mark

halfway between the edges. The center of

any adjacent studs should be 16” (40.6 cm)

or 24” (61 cm) from this mark.

3. Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

Carton

Styrofoam

Mounting

Plate

Screws

Wall

Studs

Center

10

English

C. DETERMINING WALL PLATE LOCATION UNDER YOUR

CABINET.

PLATE POSITION—BENEATH FLAT BOTTOM

CABINET

PLATE POSITION—BENEATH RECESSED

BOTTOM CABINET WITH FRONT OVERHANG

PLATE POSITION—BENEATH FRAMED RECESSED

CABINET BOTTOM

Mounting Plate Tabs

Touching the Cabinet Bottom

At least 30

ʺ

(76.2 cm),

up to 36

ʺ

(91.4 cm)

30ʺ(76.2 cm)

to Cooktop

Mounting Plate Tabs

Touching the Back Frame

Mounting Plate with

Tabs Below Cabinet

Bottom the Same

Distance as the Front

Overhang Depth

30ʺ(76.2 cm)

to Cooktop

Your cabinets may have decorative trim that interferes with the microwave installation.

Remove the decorative trim to install the microwave properly and to make it level.

THE MICROWAVE MUST BE LEVEL. Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no back or side frame, install the

mounting plate down the same distance as the front overhang depth. This will keep

the microwave level.

Measure the inside depth of the 1. front overhang.

Draw a horizontal line on the back wall an equal distance below the cabinet 2.

bottom as the inside depth of the front overhang.

For this type of installation with front overhang only, align the mounting tabs with 3.

this horizontal line, not touching the cabinet bottom as described in Step D.

CAUTION:

Wear gloves to avoid cutting fingers on sharp edges.

11

English

D. ALIGNING THE WALL PLATE

Draw a vertical line on the wall at the center of the 30” (76.2 cm) wide space.1.

Use the mounting plate 2. as the template for the rear wall. Place the mounting

plate on the wall, making sure that the tabs are touching the bottom of the

cabinet or the level line drawn in Step C for cabinets with front overhang.

Line up the notch and centerline on the bottom of the mounting plate to the

centerline on the wall.

While holding the mounting plate with one hand, draw circles on the wall 3.

at holes A, B, C and D (see illustration above/actual plate marked with

arrows). Four holes must be used for mounting.

NOTE: If neither C nor D is in a stud, find a stud somewhere in area E and

draw a fifth circle to line up with the stud. It is important to use at least one

wood screw mounted firmly in a stud to support the weight of the microwave.

Set the mounting plate aside.

Drill holes on the circles. If there is a stud, drill a 3⁄16” hole for wood screws. 4.

For holes that don’t line up with a stud, drill a 5⁄8” hole for toggle bolts.

NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.

Draw a Vertical

Line on Wall

from Center of

Top Cabinet

Area E

Hole A

Hole B

Hole D

Hole C

Centerline

Notches

12

English

This microwave oven is designed for adaptation to the following three types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)If direct-wiring microwave

NOTE: This microwave is shipped assembled for Recirculating. Select the type of

ventilation required for your installation and proceed to the section.

2. INSTALLATION TYPES (Choose A,B or C)

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)

B. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

C. RECIRCULATING (NON-VENTED DUCTLESS)

Adaptor in Place for

Outside Top Exhaust

Adaptor Must Be

Moved to the Back for

Outside Back Exhaust

On models shipped for

recirculating exhaust,

a disposable charcoal

ﬁlter is factory installed

to help remove smoke

and odors.

Page 13

Page 17

Page 22

13

English

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Adapting Microwave Blower

for Outside Top Exhaust

A4. Check Damper Operation

A5. Mount Microwave Oven

A6. Adjust Exhaust Adaptor

A7. Connect Ductwork

Attach the plate to the wall using toggle

bolts. At least one wood screw must be

used to attach the plate to a wall stud.

Remove the toggle wings from the bolts. 1.

Insert the bolts into the mounting plate 2.

through the holes designated to go into

drywall and reattach the toggle wings to

3⁄4” (19 mm) onto each bolt.

TO USE TOGGLE BOLTS:

Place the mounting plate against the 3.

wall and insert the toggle wings into the

holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw,

make sure the tabs on the mounting plate touch the

bottom of the cabinet when pushed flush against the wall

and that the plate is properly centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and thewall.

Tighten all bolts. Pull the plate away 4.

from the wall to help tighten the bolts.

A1. ATTACH THE MOUNTING PLATE TO THE WALL

IMPORTANT NOTES:

Make sure the screws for the blower motor and blower plate are securely t

tightened when they are reinstalled. This will help to prevent excessive vibration

Make sure the motor wiring has been properly routed and secured, and that t

the wires are not pinched.

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)

Wall

Mounting

Plate

Spacing for Toggles

More Than Wall

Thickness

Bolt End

Toggle

Bolt

Toggle Wings

14

English

You need to drill holes for the top support

screws, a hole large enough for the power

cord to fit through, and a cutout large

enough for the exhaust adaptor.

t3FBEUIFJOTUSVDUJPOTPOUIF501 

CABINET TEMPLATE.

t5BQFJUVOEFSOFBUIUIFUPQDBCJOFU

t%SJMMUIFIPMFTGPMMPXJOHUIFJOTUSVDUJPOT

on the TOP CABINET TEMPLATE.

CAUTION:

Wear safety goggles when drilling holes in the cabinet bottom.

Place the microwave in its upright 1.

position,with the top of the unit facing up.

Remove the screw that holds the blower

plate to the microwave. Remove and

save the screw holding the blower motor

to the microwave.

Carefully pull out the blower unit. The 2.

wires will extend far enough to allow

you to adjust the blower unit.

Roll the blower unit 90° so that fan 3.

blade openings are facing out the top

of the microwave.

A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF

TOP CABINET

A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE

TOP EXHAUST

Blower Plate

Blower Moto

Screw

Back of

Microwave

End B

End A

Back of

Microwave

Back of

Microwave

Before Rotation After Rotation

Back of

Microwave

English

FOR EASIER INSTALLATION

AND PERSONAL SAFETY, WE

RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

15

English

4. Place the blower unit back into the

opening.

5. Secure blower unit to microwave with

the screw removed in Step 1. Make

sure the screw is tight.

6. Replace blower plate with the screw

removed in Step 1. Make sure the

screw is tight.

7. Attach the exhaust adaptor to the

top of the blower plate by sliding it

into the guides of the blower plate.

Push in securely until it is in the

locking tabs. Take care to assure

that the damper hinge is installed so

that the damper swings freely.

t.BLFTVSFUBQFTFDVSJOHEBNQFSJT

removed and damper pivots easily

before mounting microwave.

t:PVXJMMOFFEUPNBLFBEKVTUNFOUT

to assure proper alignment with your

house exhaust duct after the microwave

is installed.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the

nylon grommet around the power cord

hole to prevent cutting of the cord.

NOTE: We recommend using filler

blocks if the cabinet front hangs below

the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from

overtightening screws.

A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE

TOP EXHAUST

A4. CHECK FOR PROPER DAMPER OPERATION

A5. MOUNT THE MICROWAVE OVEN

Back of

Microwave

Back of

Microwave

Guide

Adaptor

Locking Tab

Exhaust Adaptor

Blower Plate

Damper

Back of

Microwave

Back of

Microwave

AFTER: Fan Blade

Openings Facing Top

English

16

English

Lift microwave, tilt it forward, and hook slots 1.

at back bottom edge onto four lower tabs of

mounting plate.

Rotate front of oven up against cabinet 2.

bottom.

Insert a self-aligning screw through top 3.

center cabinet hole. Temporarily secure

the oven by turning the screw at least two

full turns after the threads have engaged.

(It will be completely tightened later.) Be

sure to keep power cord tight. Be careful

not to pinch the cord, especially when

mounting flush to bottom of cabinet.

Attach the microwave oven to the top cabinet.4.

Insert 2 self-aligning screws through outer 5.

top cabinet holes. Turn two full turns on

each screw.

Tighten center screw completely.6.

Open the top cabinet and adjust the exhaust

adaptor to connect to the house duct.

Extend the house duct down to connect 1.

to the exhaust adaptor.

Seal exhaust duct joints using duct tape.2.

7. Tighten the outer two screws to the top of the microwave oven. (While tightening

screws, hold the microwave oven in place against the wall and the top cabinet.)

8. Install grease filters. See the Owner’s Manual packed with the microwave.

A5. MOUNT THE MICROWAVE OVEN

A6. ADJUST THE EXHAUST ADAPTOR

A7. CONNECTING DUCTWORK

Cabinet Front

Cabinet Bottom Shelf

Filler Block

Microwave Oven Top

Equivalent

to Depth

of Cabinet

Recess

Self-Aligning Screw

Back of

Microwave

For Front-to-Back or

Side-to-Side Adjustment,

Slide the Exhaust Adaptor

as Needed

Blower Plate

Damper

House Duct

NOTE: When mounting the

microwave oven, thread power

cord through hole in bottom

of top cabinet. Keep it tight

throughout Steps 1–3. Do

not pinch cord or lift oven by

pulling cord.

1

2

5

6

English

17

English

INSTALLATION OVERVIEW

B1. Prepare Rear Wall

B2. Remove Blower Plate

B3. Attach Mounting Plate to Wall

B4. Prepare Top Cabinet

B5. Adjust Blower

B6. Mount the Microwave Oven

You need to cut an opening in the rear

wall for outside exhaust.

Read the instructions on the REAR t

WALL TEMPLATE.

Tape it to the rear wall, lining up with t

the holes previously drilled for holes A

and B in the wall plate.

Cut the opening, following the t

instructions of the REAR WALL

TEMPLATE.

Remove and save the screw that holds the

blower plate to the microwave. Lift off the

blower plate.

B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST

B2. REMOVE BLOWER PLATE

B. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)

Back of

Microwave

Blower Plate

IMPORTANT NOTES:

Make sure the screws for the blower motor and blower plate are securely t

tightened when they are reinstalled. This will help to prevent excessive vibration

Make sure the motor wiring has been properly routed and secured, and that t

the wires are not pinched.

English

18

English

Attach the plate to the wall using toggle

bolts. At least one wood screw must be

used to attach the plate to a wall stud.

Remove the toggle wings from the bolts. 1.

Insert the bolts into the mounting plate 2.

through the holes designated to go into

drywall and reattach the toggle wings to

3⁄4” (19 mm) onto each bolt.

TO USE TOGGLE BOLTS:

Place the mounting plate against the 3.

wall and insert the toggle wings into the

holes in the wall to mount the plate.

NOTE: Before tightening toggle bolts and wood screw,

make sure the tabs on the mounting plate touch the

bottom of the cabinet when pushed flush against the wall

and that the plate is properly centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and thewall.

Tighten all bolts. Pull the plate away 4.

from the wall to help tighten the bolts.

B3. ATTACH THE MOUNTING PLATE TO THE WALL

Wall

Mounting

Plate

Spacing for Toggles

More Than Wall

Thickness

Bolt End

Toggle

Bolt

Toggle Wings

You need to drill holes for the top support

screws, a hole large enough for the power

cord to fit through.

Read the instructions on the TOP t

CABINET TEMPLATE.

Tape it underneath the top cabinet.t

Drill the holes, following the instructions t

on the TOP CABINET TEMPLATE.

B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF

TOP CABINET

CAUTION:

Wear safety goggles when drilling holes in the cabinet bottom.

English

B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK

EXHAUST

Remove and save screw that holds 1.

blower motor to microwave.

Carefully pull out the blower unit. The 2.

wires will extend far enough to

allow you to adjust the blower unit.

Roll the blower unit 90° 3.

5. Gently remove the wires from the

grooves. Reroute the wires through

grooves on other side of the blower unit.

7. Place the blower unit back into the

opening.

CAUTION: Do not pull or stretch the

blower unit wiring. Make sure the wires

are not pinched, and that they are

properly secured.

NOTE: The blower unit exhaust

openings should match exhaust

openings on rear of microwave oven.

8. Secure the blower unit to the

microwave with the original screw.

9. Replace the blower plate in the

same position as before with the

screw. Make sure the screw is tight.

4. Rotate blower unit counterclockwise 180°.

6. Roll the blower unit 90° so that fan blade

openings are facing out the back of the

microwave.

Back of

Microwave

Blower Motor

Screw

Blower Plate

Blower Motor

Screw

Back of

Microwave

End B

End A

Forward

Openings Facing

Before: Fan Blade

Back of

Microwave

Before Rotation After Rotation

Back of

Microwave

Before Rotation After Rotation

Back of

Microwave

Back of

Microwave

Before Rerouting After Rerouting

Wires Routed Through Right Side

Wires Routed Through Left Side

Before Rolling After Rolling

Back of

Microwave

Back of

Microwave

AFTER: Fan Blade

Openings Facing Back

End A

End B

19

La page charge ...

Haier HMV1630HBSA Manuel utilisateur

Ce manuel convient également à

Haier HMV1630HBSA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents