Lincoln Electric LN-25 Pro Mode d'emploi
- Catégorie
- Système de soudage
- Taper
- Mode d'emploi
'(*,'*Z+Y%&-$
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © Lincoln Global Inc.
LN™- 25 PIPE
!%
April, 2011
For use with machines having Code Number: 11693
+387FK7B7@6EA@0AG
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thoughtful
operation on your part. ' &',
!&+,$$'(*,'* *(!*
, !+ )-!(%&, /!, '-,
*!& , !+ %&-$ &
, +,0 (*-,!'&+
'&,!& , *'- '-,
And, most importantly, think before
you act and be careful.
!(
!Y
THANK YOU FOR SELECTING
A QUALITY PRODUCT BY
LINCOLN ELEC TRIC.
PLEASE EXAMINE CARTON AND EQUIPMENT FOR
DAMAGE IMMEDIATELY
When this equipment is shipped, title passes to the purchaser
upon receipt by the carrier. Consequently, claims for material
damaged in shipment must be made by the purchaser against the
transportation company at the time the shipment is received.
SAFETY DEPENDS ON YOU
Lincoln arc welding and cutting equipment is designed and built
with safety in mind. However, your overall safety can be increased
by proper installation ... and thoughtful operation on your part.
DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT
WITHOUT READING THIS MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly,
think before you act and be careful.
This statement appears where the information must be followed
exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed
to avoid minor personal injury or damage to this equipment.
KEEP YOUR HEAD OUT OF THE FUMES.
DON’T get too close to the arc.
Use corrective lenses if necessary
to stay a reasonable distance
away from the arc.
READ and obey the Safety Data
Sheet (SDS) and the warning label
that appears on all containers of
welding materials.
USE ENOUGH VENTILATION or
exhaust at the arc, or both, to
keep the fumes and gases from
your breathing zone and the general area.
IN A LARGE ROOM OR OUTDOORS, natural ventilation may be
adequate if you keep your head out of the fumes (See below).
USE NATURAL DRAFTS or fans to keep the fumes away
from your face.
If you de velop unusual symptoms, see your supervisor.
Perhaps the welding atmosphere and ventilation system
should be checked.
WEAR CORRECT EYE, EAR &
BODY PROTECTION
PROTECT your eyes and face with welding helmet
properly fitted and with proper grade of filter plate
(See ANSI Z49.1).
PROTECT your body from welding spatter and arc
flash with protective clothing including woolen
clothing, flame-proof apron and gloves, leather
leggings, and high boots.
PROTECT others from splatter, flash, and glare
with protective screens or barriers.
IN SOME AREAS, protection from noise may be appropriate.
BE SURE protective equipment is in good condition.
Also, wear safety glasses in work area
AT ALL TIMES.
SPECIAL SITUATIONS
DO NOT WELD OR CUT containers or materials which previously
had been in contact with hazardous substances unless they are
properly cleaned. This is extremely dangerous.
DO NOT WELD OR CUT painted or plated parts unless special
precautions with ventilation have been taken. They can release
highly toxic fumes or gases.
Additional precautionary measures
PROTECT compressed gas cylinders from excessive heat,
mechanical shocks, and arcs; fasten cylinders so they cannot fall.
BE SURE cylinders are never grounded or part of an
electrical circuit.
REMOVE all potential fire hazards from welding area.
ALWAYS HAVE FIRE FIGHTING EQUIPMENT READY FOR
IMMEDIATE USE AND KNOW HOW TO USE IT.
WARNING
CAUTION
Safety 01 of 04 - 5/16/2018
SECTION A:
WARNINGS
CALIFORNIA PROPOSITION 65 WARNINGS
WARNING: Breathing diesel engine exhaust
exposes you to chemicals known to the State
of California to cause cancer and birth defects,
or other reproductive harm.
• Always start and operate the engine in a
well-ventilated area.
• If in an exposed area, vent the exhaust to the outside.
• Do not modify or tamper with the exhaust system.
• Do not idle the engine except as necessary.
For more information go to
www.P65 warnings.ca.gov/diesel
WARNING: This product, when used for welding or
cutting, produces fumes or gases which contain
chemicals known to the State of California to cause
birth defects and, in some cases, cancer. (California
Health & Safety Code § 25249.5 et seq.)
WARNING: Cancer and Reproductive Harm
www.P65warnings.ca.gov
ARC WELDING CAN BE HAZARDOUS. PROTECT
YOURSELF AND OTHERS FROM POSSIBLE SERIOUS
INJURY OR DEATH. KEEP CHILDREN AWAY.
PACEMAKER WEARERS SHOULD CONSULT WITH
THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For
additional safety information, it is strongly recommended
that you purchase a copy of “Safety in Welding & Cutting -
ANSI Standard Z49.1” from the American Welding Society,
P.O. Box 351040, Miami, Florida 33135 or CSA Standard
W117.2-1974. A Free copy of “Arc Welding Safety” booklet
E205 is available from the Lincoln Electric Company,
22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION,
MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
FOR ENGINE POWERED
EQUIPMENT.
1.a. Turn the engine off before troubleshooting
and maintenance work unless the
maintenance work requires it to be running.
1.b. Operate engines in open, well-ventilated areas or vent the engine
exhaust fumes outdoors.
1.c. Do not add the fuel near an open flame welding
arc or when the engine is running. Stop the
engine and allow it to cool before refueling to
prevent spilled fuel from vaporizing on contact
with hot engine parts and igniting. Do not spill fuel when filling
tank. If fuel is spilled, wipe it up and do not start engine until
fumes have been eliminated.
1.d. Keep all equipment safety guards, covers
and devices in position and in good repair.
Keep hands, hair, clothing and tools away
from V-belts, gears, fans and all other
moving parts when starting, operating or
repairing equipment.
1.e. In some cases it may be necessary to remove safety guards to
perform required maintenance. Remove guards only when
necessary and replace them when the maintenance requiring
their removal is complete. Always use the greatest care when
working near moving parts.
1.f. Do not put your hands near the engine fan. Do not attempt to
override the governor or idler by pushing on the throttle control
rods while the engine is running.
1.g. To prevent accidentally starting gasoline engines while turning
the engine or welding generator during maintenance work,
disconnect the spark plug wires, distributor cap or magneto wire
as appropriate.
1.h. To avoid scalding, do not remove the radiator
pressure cap when the engine is
hot.
ELECTRIC AND
MAGNETIC FIELDS MAY
BE DANGEROUS
2.a. Electric current flowing through any conductor
causes localized Electric and Magnetic Fields (EMF).
Welding current creates EMF fields around welding cables
and welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health effects
which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and work
cables. If the electrode cable is on your right side, the
work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as pos-
sible to the area being welded.
2.d.5. Do not work next to welding power source.
SAFETY
Safety 02 of 04 - 5/16/2018
ELECTRIC SHOCK
CAN KILL.
3.a. The electrode and work (or ground) circuits are
electrically “hot” when the welder is on. Do
not touch these “hot” parts with your bare skin or wet clothing.
Wear dry, hole-free gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full area
of physical contact with work and ground.
In addition to the normal safety precautions, if
welding must be performed under electrically
hazardous conditions (in damp locations or while
wearing wet clothing; on metal structures such as
floors, gratings or scaffolds; when in cramped
positions such as sitting, kneeling or lying, if there
is a high risk of unavoidable or accidental contact
with the workpiece or ground) use the following
equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic welding
gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection should
be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical (earth)
ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of electrode
holders connected to two welders because voltage
between the
two can be the total of the open circuit voltage of both
welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see It ems 6.c. and 8.
ARC RAYS CAN BURN.
4.a. Use a shield with the proper filter and cover plates to protect your
eyes from sparks and the rays of the arc when welding or
observing open arc welding. Headshield and filter lens should
conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant material
to protect your skin and that of your helpers from the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
FUMES AND GASES
CAN BE DANGEROUS.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases. When welding, keep your head out of the fume.
Use enough ventilation and/or exhaust at the arc to keep fumes
and gases away from the breathing zone. When welding
hardfacing (see instructions on container or SDS)
or on lead or cadmium plated steel and other
metals or coatings which produce highly toxic
fumes, keep exposure as low as possible and
within applicable OSHA PEL and ACGIH TLV limits
using local exhaust or mechanical ventilation
unless exposure assessments indicate otherwise.
In confined spaces or in some circumstances,
outdoors, a respirator may also be required.
Additional precautions are also required when
welding
on galvanized steel.
5. b. The operation of welding fume control equipment is affected by
various factors including proper use and positioning of the
equipment, maintenance of the equipment and the specific
welding procedure and application involved. Worker exposure
level should be checked upon installation and periodically
thereafter to be certain it is within applicable OSHA PEL and
ACGIH TLV limits.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations. The
heat and rays of the arc can react with solvent vapors to form
phosgene, a highly toxic gas, and other irritating products.
5.d. Shielding gases used for arc welding can displace air and
cause
injury or death. Always use enough ventilation, especially in
confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
Safety Data Sheet (SDS) and follow your employer’s safety
practices. SDS forms are available from your welding
distributor or from the manufacturer.
5.f. Also see item 1.b.
SAFETY
Safety 03 of 04 - 5/16/2018
WELDING AND CUTTING
SPARKS CAN CAUSE
FIRE OR EXPLOSION.
6.a. Remove fire hazards from the welding area. If
this is not possible, cover them to prevent the welding sparks
from starting a fire. Remember that welding sparks and hot
materials from welding can easily go through small cracks and
openings to adjacent areas. Avoid welding near hydraulic lines.
Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site, special
precautions should be used to prevent hazardous situations.
Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1)
and the operating information for the equipment being used.
6.c. When not welding, make certain no part of the electrode circuit is
touching the work or ground. Accidental contact can cause
overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances inside.
They can cause an explosion even though they have been
“cleaned”. For information, purchase “Recommended Safe
Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous Substances”,
AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil free
protective garments such as leather gloves, heavy shirt, cuffless
trousers, high shoes and a cap over your hair. Wear ear plugs
when welding out of position or in confined places. Always wear
safety glasses with side shields when in a welding area.
6.g. Connect the work cable to the work as close to the welding area
as practical. Work cables connected to the building framework or
other locations away from the welding area increase the
possibility of the welding current passing through lifting chains,
crane cables or other alternate circuits. This can create fire
hazards or overheat lifting chains or cables until they fail.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “Standard for Fire Prevention During
Welding, Cutting and Other Hot Work”, available from NFPA, 1
Batterymarch Park, PO box 9101, Quincy, MA 022690-9101.
6.j. Do not use a welding power source for pipe thawing.
CYLINDER MAY EXPLODE IF
DAMAGED.
7.a. Use only compressed gas cylinders containing
the correct shielding gas for the process used
and properly operating regulators designed for
the gas and pressure used. All hoses, fittings,
etc. should be suitable for the application and
maintained in good condition.
7.b. Always keep cylinders in an upright position securely chained to
an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected
to physical damage.
• A safe distance from arc welding or cutting operations
and any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand tight
except when the cylinder is in use or connected for use.
7.g. Read and follow the instructions on compressed gas cylinders,
associated equipment, and CGA publication P-l, “Precautions for
Safe Handling of Compressed Gases in Cylinders,” available from
the Compressed Gas Association, 14501 George Carter Way
Chantilly, VA 20151.
FOR ELECTRICALLY
POWERED EQUIPMENT.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National Electrical
Code, all local codes and the manufacturer’s recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
Refer to
http://www.lincolnelectric.com/safety
for additional safety information.
SAFETY
Safety 04 of 04 - 5/16/2018
;H
+,0
;H
(*M-,!'&++X*,M
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
+OD7FN(AGD+AG6397$ZD5
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
(*M-,!'&++X*,M('-*
$+% !&+T+'-*T
,*&+'*%,-*,T
**++-*
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
vv
SAFETY
Electromagnetic Compatibility (EMC)
Conformance
Products displaying the CE mark are in conformity with European Community Council Directive of 15 Dec
2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility,
2004/108/EC. It was manufactured in conformity with a national standard that implements a harmonized
standard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment.
It is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.
Introduction
All electrical equipment generates small amounts of electromagnetic emission. Electrical emission may be
transmitted through power lines or radiated through space, similar to a radio transmitter. When emissions
are received by other equipment, electrical interference may result. Electrical emissions may affect many
kinds of electrical equipment; other nearby welding equipment, radio and TV reception, numerical controlled
machines, telephone systems, computers, etc. Be aware that interference may result and extra precautions
may be required when a welding power source is used in a domestic establishment.
Installation and Use
The user is responsible for installing and using the welding equipment according to the manufacturer’s
instructions. If electromagnetic disturbances are detected then it shall be the responsibility of the user of the
welding equipment to resolve the situation with the technical assistance of the manufacturer. In some cases
this remedial action may be as simple as earthing (grounding) the welding circuit, see Note. In other cases it
could involve construction of an electromagnetic screen enclosing the power source and the work complete
with associated input filters. In all cases electromagnetic disturbances must be reduced to the point where
they are no longer troublesome.
Note: The welding circuit may or may not be earthed for safety reasons according to national codes.
Changing the earthing arrangements should only be authorized by a person who is compe-
tent to access whether the changes will increase the risk of injury, e.g., by allowing parallel
welding current return paths which may damage the earth circuits of other equipment.
Assessment of Area
Before installing welding equipment the user shall make an assessment of potential electromagnetic prob-
lems in the surrounding area. The following shall be taken into account:
a) other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the
welding equipment;
b) radio and television transmitters and receivers;
c) computer and other control equipment;
d) safety critical equipment, e.g., guarding of industrial equipment;
e) the health of the people around, e.g., the use of pacemakers and hearing aids;
f) equipment used for calibration or measurement
g) the immunity of other equipment in the environment. The user shall ensure that other equipment being
used in the environment is compatible. This may require additional protection measures;
h) the time of day that welding or other activities are to be carried out.
SAFETY
vivi
Electromagnetic Compatibility (EMC)
The size of the surrounding area to be considered will depend on the structure of the building and other
activities that are taking place. The surrounding area may extend beyond the boundaries of the premises.
Methods of Reducing Emissions
Mains Supply
Welding equipment should be connected to the mains supply according to the manufacturer’s recommenda-
tions. If interference occurs, it may be necessary to take additional precautions such as filtering of the mains
supply. Consideration should be given to shielding the supply cable of permanently installed welding equip-
ment, in metallic conduit or equivalent. Shielding should be electrically continuous throughout its length. The
shielding should be connected to the welding power source so that good electrical contact is maintained
between the conduit and the welding power source enclosure.
Maintenance of the Welding Equipment
The welding equipment should be routinely maintained according to the manufacturer’s recommendations.
All access and service doors and covers should be closed and properly fastened when the welding equip-
ment is in operation. The welding equipment should not be modified in any way except for those changes
and adjustments covered in the manufacturers instructions. In particular, the spark gaps of arc striking and
stabilizing devices should be adjusted and maintained according to the manufacturer’s recommendations.
Welding Cables
The welding cables should be kept as short as possible and should be positioned close together, running at
or close to floor level.
Equipotential Bonding
Bonding of all metallic components in the welding installation and adjacent to it should be considered.
However, metallic components bonded to the work piece will increase the risk that the operator could
receive a shock by touching these metallic components and the electrode at the same time. The operator
should be insulated from all such bonded metallic components.
Earthing of the Workpiece
Where the workpiece is not bonded to earth for electrical safety, not connected to earth because of its size
and position, e.g., ships hull or building steelwork, a connection bonding the workpiece to earth may reduce
emissions in some, but not all instances. Care should be taken to prevent the earthing of the workpiece
increasing the risk of injury to users, or damage to other electrical equipment. Where necessary, the connec-
tion of the workpiece to earth should be made by a direct connection to the workpiece, but in some countries
where direct connection is not permitted, the bonding should be achieved by suitable capacitance, selected
according to national regulations.
Screening and Shielding
Selective screening and shielding of other cables and equipment in the surrounding area may alleviate prob-
lems of interference. Screening of the entire welding installation may be considered for special
applications
1.
_________________________
1
Portions of the preceding text are contained in EN 60974-10: “Electromagnetic Compatibility (EMC) prod-
uct standard for arc welding equipment.”
H;;;
H;;;
,$''&,&,+
Page
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
!@EF3>>3F;A@+75F;A@
Technical Specifications.......................................................................................................A-1
Safety Precautions ...............................................................................................................A-2
Location................................................................................................................................A-2
High Frequency Protection...................................................................................................A-2
Weld cable Sizes..................................................................................................................A-2
Analog Control Cable ...........................................................................................................A-3
Cable Connections and Control Cable Connector ...............................................................A-4
Shielding Gas Connection....................................................................................................A-4
Wire Drive Configuration ......................................................................................................A-5
Changing The Gun Receiver Bushing................................................................................A-5
Procedure to Install Drive Rolls and Wire Guides ..............................................................A-5
Pressure Arm Adjustment ....................................................................................................A-5
Loading Spools of Wire ........................................................................................................A-5
Gun Connections..................................................................................................................A-5
Power Source to LN™-25 PIPE Connection Diagrams ...............................................A-6, A-7
________________________________________________________________________________
'B7D3F;A@+75F;A@
Safety Precautions ...............................................................................................................B-1
Graphic Symbols that appear on this Machine or in this Manual .........................................B-1
Definition of Welding Terms .................................................................................................B-2
General Description..............................................................................................................B-2
Recommended Processes, Equipment Limitations, Recommended Power Sources ..........B-2
Case Front Controls ...............................................................................................B-3 thru B-6
Internal Controls ...................................................................................................................B-7
Internal Controls Decription..................................................................................................B-8
Rear Controls .......................................................................................................................B-9
________________________________________________________________________________
557EEAD;7E +75F;A@
Factory Installed Equipment.................................................................................................C-1
Drive Roll Kits used..............................................................................................................C-1
Accessories Used ..................................................................................................C-2 thru C-4
________________________________________________________________________________
%3;@F7@3@57+75F;A@
Safety Precautions ...............................................................................................................D-1
Routine Maintenance ...........................................................................................................D-1
Periodic Maintenance...........................................................................................................D-1
________________________________________________________________________________
,DAG4>7E:AAF;@9 +75F;A@
How to Use Troubleshooting Guide .....................................................................................E-1
Error Codes ..........................................................................................................................E-2
Troubleshooting Guide .................................................................................................E-3, E-4
________________________________________________________________________________
/;D;@9;39D3?;?7@E;A@(D;@FE +75F;A@
22222222222222222222222222222222222222222222222222222222222222222222222222222222
(3DFE(397E (+7D;7E
22222222222222222222222222222222222222222222222222222222222222222222222
22222222
!&+,$$,!'&
$&R(!(
,%(*,-**&
'(*,!'& -40°F to 104°F (-40°C to 40°C)
+,'* -40°F to 185°F (-40°C to 85°C)
!&(-,.'$,3@6-**&,
, &!$+(!!,!'&+U$&R(!(#
! , /!, (, /! ,
14.8 Inches 8.7 Inches 22.2 Inches 41 lbs
(376 mm) ( 221 mm) (589 mm) (18.6 kg)
Handle folded down
( 0+!$!%&+!'&+
!&(-,.'$,S
15-110 VDC
!&(-,%(*+
4A
*,'-,(-,PP
-,00$
60% rating
!&(-,%(*+
450
*!&/!*+(*&/!*+!1
/+*&
50 – 700 ipm
(1.3 – 17.7m/min)
/+*&
50 – 700 ipm
(1.3 – 17.7m/min)
/!*+!1+
.023 – 1/16"
(0.6 – 1.6mm)
/!*+!1+
.030 - 5/64
(0.8 - 2.0mm)
*!&
Standard Speed
K2614-5
GMAW
FCAW
Thermal tests have been performed at ambient temperature. The Duty Cycle (duty factor) @ 40ºC (104°F) has
been determined by simulation.
/$$+!1
Table A.1 located below are copper cable sizes rec-
ommended for different currents and duty cycles.
Lengths stipulated are the distance from the welder to
work and back to the welder again. Cable sizes are
increased for greater lengths primarily for the purpose
of minimizing cable drop.
** Tabled values are for operation at ambient temperatures of 104°F(40°C) and below. Applications above 104°F(40°C) may require cables
larger than recommended, or cables rated higher than 167°F(75°C).
*'%%&$+!1+*-*'.*'((**,PADP
CABLE SIZES FOR COMBINED LENGTHS OF ELECTRODE AND WORK CABLES
AMPERES
200
200
225
225
250
250
250
250
300
325
350
400
400
500
PERCENT
DUTY
CYCLE
60
100
20
40 & 30
30
40
60
100
60
100
60
60
100
60
FAF
FA?
2
2
4 or 5
3
3
2
1
1
1
2/0
1/0
2/0
3/0
2/0
FAF
FA?
2
2
3
3
3
2
1
1
1
2/0
1/0
2/0
3/0
2/0
FAF
FA?
2
2
2
2
2
1
1
1
1
2/0
2/0
2/0
3/0
3/0
FAF
FA?
1
1
1
1
1
1
1
1
1/0
2/0
2/0
3/0
3/0
3/0
FAF
FA?
1/0
1/0
1/0
1/0
1/0
1/0
1/0
1/0
2/0
3/0
3/0
4/0
4/0
4/0
,$
!&+,$$,!'&
$&R(!(
+,0(*-,!'&+
$,*!Y+ '#&#!$$
Q,GD@F:7;@BGFBAI7D'3FF:7
6;E5A@@75FEI;F5:AD8GE74AJ
478AD73FF7?BF;@9FA5A@@75FAD
6;E5A@@75F;@BGFBAI7D>;@7EAGF
BGF534>7EAD5A@FDA>534>7E
Q'@>KCG3>;8;76B7DEA@@7>E:AG>6
B7D8AD?F:;E;@EF3>>3F;A@
QA@AFFAG5:?7F3>BADF;A@EA8F:7$&R(!(
IAD=5>;BI:7@F:7I7>6;@9BAI7DEAGD57;EA@
QA@AF3FF35:F:7IAD=5>;BFAF:7I;D787767D
QA@@75FF:7IAD=5>;B6;D75F>KFAF:7IAD=3E
5>AE73EBAEE;4>7FAF:7I7>6;@93D5
Q,GD@BAI7DA883FF:7I7>6;@9BAI7DEAGD57
478AD76;E5A@@75F;@9F:7IAD=5>;B8DA?F:7
IAD=
Q'@>KGE7A@BAI7DEAGD57EI;F:AB7@5;D5G;F
HA>F397E>7EEF:3@.
------------------------------------------------------------------------
$',!'&
For best wire feeding performance, place the LN™-
25 PIPE on a stable and dry surface. Keep the wire
feeder in a vertical position. Do not operate the wire
feeder on an angled surface of more than 15
degrees.
Do not submerge the LN™-25 PIPE.
The LN™-25 PIPE is rated IP23 and is suitable for
outdoor use.
The handle of the LN™-25 PIPE is intended for
moving the wire feeder about the work place only.
When suspending a wire feeder, insulate the
hanging device from the wire feeder enclosure.
! *)-&0(*',,!'&
$A53F7F:7$&R(!(3I3K8DA?D36;A5A@FDA>>76
?35:;@7DK,:7@AD?3>AB7D3F;A@A8F:7$&R
(!(?3K36H7DE7>K38875FF:7AB7D3F;A@A8*5A@
FDA>>767CG;B?7@FI:;5:?3KD7EG>F;@4A6;>K;@<GDK
AD63?397FAF:77CG;B?7@F
------------------------------------------------------------------------
/*&!&
-,!'&
!&+,$$,!'&
$&R(!(
+ !$!&+'&&,!'&
0$!&*?3K 7JB>A67 ;8
63?3976
Q #77B 5K>;@67D GBD;9:F3@6
5:3;@76FAEGBBADF
Q#77B5K>;@67D3I3K8DA?3D73EI:7D7;F?3K47
63?3976
Q&7H7D>;8FI7>67DI;F:5K>;@67D3FF35:76
Q&7H7D3>>AII7>6;@97>75FDA67FAFAG5:5K>;@67D
Q#77B5K>;@67D3I3K8DA?I7>6;@9ADAF:7D>;H7
7>75FD;53>5;D5G;FE
Q-!$ -(' + !$!& + %0
*% $, '*#!$$
Q+:GF A88 E:;7>6;@993EEGBB>K I:7@ @AF
;@GE7
Q+77 ?7D;53@ &3F;A@3> +F3@63D6 1 +387FK
;@ /7>6;@9 3@6 GFF;@9W (G4>;E:76 4K F:7
?7D;53@/7>6;@9+A5;7FK
------------------------------------------------------------------------
Maximum inlet pressure is 100 psi. (6.9 bar.)
Install the shielding gas supply as follows:
1. Secure the cylinder to prevent it from falling.
2. Remove the cylinder cap. Inspect the cylinder valves
and regulator for damaged threads, dirt, dust, oil or
grease. Remove dust and dirt with a clean cloth. '
&', ,, , *-$,'* !'!$*+
'*%!+(*+&,Inform your gas supplier
of this condition. Oil or grease in the presence of high
pressure oxygen is explosive.
3. Stand to one side away from the outlet and open the
cylinder valve for an instant. This blows away any dust
or dirt which may have accumulated in the valve out-
let.
4. Attach the flow regulator to the cylinder valve and
tighten the union nut(s) securely with a wrench. Note:
if connecting to 100% CO
2
cylinder, insert regulator
adapter between regulator and cylinder valve. If
adapter is equipped with a plastic washer, be sure it is
seated for connection to the CO
2
cylinder.
5. Attach one end of the inlet hose to the outlet fitting of
the flow regulator. Attach the other end to the welding
system shielding gas inlet. Tighten the union nuts with
a wrench.
6. Before opening the cylinder valve, turn the regulator
adjusting knob counterclockwise until the adjusting
spring pressure is released.
7. Standing to one side, open the cylinder valve slowly a
fraction of a turn. When the cylinder pressure gage
stops moving, open the valve fully.
8. The flow regulator is adjustable. Adjust it to the flow
rate recommended for the procedure and process
being used before making a weld.
/*&!&
(;@
A
B
C
D
E
/;D;@9
5 volt supply
Not used
Trigger
83% WFS switch
5 volt supply
$'&&,!'&+
There is one circular connector for the gun trigger on
the front of the LN™-25 PIPE.
G@5F;A@
5-pin trigger
connector for
push-guns
only.
A
E
C
B
D
!&+,$$,!'&
$&R(!(
/!**!.'&!-*,!'&
(See Figure A.2)
&!& , -& *!.*
-+ !&
$,*!+ '#53@=;>>
Q,GD@F:7 ;@BGFBAI7D'3FF:7
I7>6;@9 BAI7D EAGD57 478AD7 ;@EF3>
>3F;A@AD5:3@9;@9 6D;H7 DA>>E 3@6AD
9G;67E
QA@AFFAG5:7>75FD;53>>K>;H7B3DFE
Q/:7@ ;@5:;@9 I;F:F:7 9G@ FD;997D 7>75FDA67
3@6 6D;H7 ?75:3@;E? 3D7 :AF FA IAD= 3@6
9DAG@63@65AG>6D7?3;@7@7D9;L76E7H7D3>E75
A@6E38F7DF:79G@FD;997D;ED7>73E76
QA @AF AB7D3F7 I;F: 5AH7DE B3@7>E AD 9G3D6E
D7?AH76ADAB7@
Q'@>KCG3>;8;76B7DEA@@7>E:AG>6B7D8AD??3;@F7
@3@57IAD=
------------------------------------------------------------------------
Tools required:
• 1/4" hex key wrench.
Note: Some gun bushings do not require the use of
the thumb screw.
1. Turn power off at the welding power source.
2. Remove the welding wire from the wire drive.
3. Remove the thumb screw from the wire drive.
4. Remove the welding gun from the wire drive.
5. Loosen the socket head cap screw that holds the
connector bar against the gun bushing.
!?BADF3@F A @AF 3FF7?BF FA 5A?B>7F7>K
D7?AH7F:7EA5=7F:73653BE5D7I
6. Remove the outer wire guide, and push the gun
bushing out of the wire drive. Because of the pre-
cision fit, light tapping may be required to remove
the gun bushing.
7. Disconnect the shielding gas hose from the gun
bushing, if required.
8. Connect the shielding gas hose to the new gun
bushing, if required.
9. Rotate the gun bushing until the thumb screw hole
aligns with the thumb screw hole in the feed plate.
Slide the gun receiver bushing into the wire drive
and verify the thumb screw holes are aligned.
10. Tighten the socket head cap screw.
11. Insert the welding gun into the gun bushing and
tighten the thumb screw.
GUN RECEIVER BUSHING
LOOSEN TIGHTEN
THUMB SCREW
OUTER WIRE GUIDE
SOCKET HEAD
CAP SCREW
CONNECTOR BLOCK
/*&!&
(*'-*,'!&+,$$*!. *'$$+
&/!*-!+
Q ,GD@F:7 ;@BGFBAI7D' 3F F:7
I7>6;@9 BAI7D EAGD57478AD7 ;@EF3>
>3F;A@ AD 5:3@9;@9 6D;H7DA>>E 3@6AD
9G;67E
QA@AFFAG5:7>75FD;53>>K>;H7B3DFE
Q/:7@ ;@5:;@9 I;F:F:7 9G@ FD;997D 7>75FDA67
3@6 6D;H7 ?75:3@;E? 3D7 :AF FA IAD= 3@6
9DAG@63@65AG>6D7?3;@7@7D9;L76E7H7D3>E75
A@6E38F7DF:79G@FD;997D;ED7>73E76
QA @AF AB7D3F7 I;F: 5AH7DE B3@7>E AD 9G3D6E
D7?AH76ADAB7@
Q'@>KCG3>;8;76B7DEA@@7>E:AG>6B7D8AD??3;@F7
@3@57IAD=
------------------------------------------------------------------------
1. Turn power off at the welding power source.
2. Release the idle roll pressure arm.
3. Remove the outer wire guide by turning the knurled
thumbscrews counter-clockwise to unscrew them
from the feed plate.
4. Rotate the triangular lock and remove the drive
rolls.
5. Remove the inner wire guide.
6. Insert the new inner wire guide, groove side out,
over the two locating pins in the feed plate.
7. Install a drive roll on each hub assembly secure
with the triangular lock.
8. Install the outer wire guide by aligning it with the
pins and tightening the knurled thumbscrews.
9. Close the idle arm and engage the idle roll pressure
arm. Adjust the pressure appropriately.
/*&!&
!-*
THUMB
SCREW
GUN
!&+,$$,!'&
$&R(!(
(*++-**%"-+,%&,
$,*!+ '#53@=;>>
Q,GD@F:7;@BGFBAI7D'3FF:7I7>6
;@9BAI7DEAGD57478AD7;@EF3>>3F;A@AD
5:3@9;@96D;H7DA>>E3@6AD9G;67E
QA@AFFAG5:7>75FD;53>>K>;H7B3DFE
Q/:7@ ;@5:;@9 I;F:F:7 9G@ FD;997D 7>75FDA67
3@6 6D;H7 ?75:3@;E? 3D7 :AF FA IAD= 3@6
9DAG@63@65AG>6D7?3;@7@7D9;L76E7H7D3>E75
A@6E38F7DF:79G@FD;997D;ED7>73E76
QA @AF AB7D3F7 I;F: 5AH7DE B3@7>E AD 9G3D6E
D7?AH76ADAB7@
Q'@>KCG3>;8;76B7DEA@@7>E:AG>6B7D8AD??3;@F7
@3@57IAD=
------------------------------------------------------------------------
The pressure arm controls the amount of force the
drive rolls exert on the wire. Proper adjustment of the
pressure arm gives the best welding performance.
Set the pressure arm as follows:
(See Figure A.3)
Aluminum wires between 1 and 2
Cored wires between 2 and 3
Steel, Stainless wires between 3 and 5
$'!&+(''$+'/!*
Q#77B:3@6E:3;D5>AF:;@93@6FAA>E
3I3K8DA?DAF3F;@97CG;B?7@F
QA@AFI73D9>AH7EI:7@F:D736;@9I;D7
AD5:3@9;@9I;D7EBAA>
Q'@>KCG3>;8;76B7DEA@@7>E:AG>6;@EF3>>
GE7ADE7DH;57F:;E7CG;B?7@F
Loading 10 to 15 lb. (4.5 – 6.8kg) Spools.
A K468 spindle adapter is required for loading 2"
(51mm) wide spools on 2" (51mm) spindles. Use a
K468 spindle adapter for loading 2-1/2" (64mm) wide
spools.
1. Squeeze the release bar on the retaining collar and
remove it from the spindle.
2. Place the spindle adapter on the spindle, aligning
the spindle brake pin with the hole in the adapter.
3. Place the spool on the spindle and align the
adapter brake tab with one of the holes in the back
side of the spool. An indicator mark on the end of
the spindle shows the orientation of the brake tab.
Be certain the wire feeds off of the spool in the
proper direction.
4. Re-install the retaining collar. Make sure that the
release bar snaps out and that the retaining collar
fully engages the groove on the spindle.
-&'&&,!'&
$,*!+ '#53@=;>>
Q,GD@F:7;@BGFBAI7D'3FF:7I7>6
;@9BAI7DEAGD57478AD7;@EF3>>3F;A@AD
5:3@9;@96D;H7DA>>E3@6AD9G;67E
QA@AFFAG5:7>75FD;53>>K>;H7B3DFE
Q/:7@ ;@5:;@9 I;F:F:7 9G@ FD;997D 7>75FDA67
3@6 6D;H7 ?75:3@;E? 3D7 :AF FA IAD= 3@6
9DAG@63@65AG>6D7?3;@7@7D9;L76E7H7D3>E75
A@6E38F7DF:79G@FD;997D;ED7>73E76
QA @AF AB7D3F7 I;F: 5AH7DE B3@7>E AD 9G3D6E
D7?AH76ADAB7@
Q'@>KCG3>;8;76B7DEA@@7>E:AG>6B7D8AD??3;@F7
@3@57IAD=
------------------------------------------------------------------------
The LN™-25 PIPE comes with a K1500-2 gun adapter
installed. (See Figure A.4)
To install a gun,
1. Turn power OFF.
2. Remove the thumb screw.
3. Push the gun the completely into the gun bushing.
4. Secure the gun in place with the thumb screw.
5. Connect the trigger cable from the gun to the trigger
connector on the front of the feeder.
Note: Not all gun bushings require the use of the
thumb screw.
/*&!&
/*&!&
6
Al
Fe, CrNi
Fe, CrNi
ALUMINUM WIRES
CORED WIRES
STEEL, STAINLESS WIRES
!-*
/*&!&
!-*
. (AI7D+AGD57E I;F: +FG6A@@75FADE3@6 @A
*7?AF7$A53>+I;F5:+77;9GD7
Place CV/CC switch in the feeder in the "CV" position.
Work clip
Work
Electrode
Jumper
LN™-25 PIPE
Ranger 250, 250 LPG
Ranger 305G, 305D
Ranger 10,000
Ranger 3 Phase
Ranger 225GXT
Ranger 225
Commander 300
Vantage 300, 400, 500
Air Vantage 500
!-*
!&+,$$,!'&
$&R(!(
. (AI7D +AGD57E I;F: +FG6A@@75FADE 3@6
*7?AF7$A53>+I;F5:+77;9GD7
Place the power source Remote/Local switch in the
Local position.
Place CV/CC switch in the feeder in the "CV" position.
Work clip
Work
Electrode
(Across the Arc)
LN™-25 PIPE
CV-400
CV-655
DC-400
DC-600
DC-655
V450-Pro
SAE 400 with CV adapter
Engine Driven welder with
Wire Feed Module
Ranger 250 GXT
!-*
('/*+'-*,'$&R(!(
$'&&,!'&!*%+
#
K2614-5
KP1695-XX
KP1696-XX
KP1697-XX
See magnum Literature
K1803-1
7E5D;BF;A@
LN™-25 PIPE
Drive Roll Kit
Welding Gun
CV power Source
Welding Cables
#
K2614-5
K484*
KP1695-XX
KP1696-XX
KP1697-XX
See Magnum Literature
K1803-1
7E5D;BF;A@
LN™-25 PIPE
Jumper Plug Kit
Drive Roll Kit
Welding Gun
CV power Source
Welding Cables
*If Power Source has a 14-Pin Cable connector and no
“Output Terminal” switch.
!&+,$$,!'&
$&R(!(
.(AI7D+AGD57I;F:,I;EF%3F7A@@75FADE3@6
*7?AF7$A53>+I;F5:+77;9GD7
Place CV/CC switch in the feeder in the "CV" position.
Work clip
Work
Electrode
LN™-25 PIPE
CV-305
V350-Pro
!-*
#
K2614-5
KP1695-XX
KP1696-XX
KP1697-XX
See Magnum Literature
K1841
7E5D;BF;A@
LN™-25 PIPE
Drive Roll Kit
Welding Gun
CV power Source
Welding Cables
.(AI7D+AGD57I;F:,I;EF%3F7A@@75FADE3@6
@A*7?AF7$A53>+I;F5:+77;9GD7
Place CV/CC switch in the feeder in the "CV" position.
Work clip
Work
Electrode
Jumper
LN™-25 PIPE
CV-250
CV-300
!-*
#
K2614-5
KP1695-XX
KP1696-XX
KP1697-XX
See Magnum Literature
K1841-
K852-95
K484
7E5D;BF;A@
LN™-25 PIPE
Drive Roll Kit
Welding Gun
CV power Source
Welding Cables
Twist-Mate Cable Plug
Jumper Plug kit
'(*,!'&
$&R(!(
Q$,*! + '# & #!$$
-@>7EEGE;@9 '$ 873
FGD7I:7@8776;@9I;F:9G@FD;9
97D F:7 7>75FDA673@6 6D;H7
?75:3@;E? 3D7 3>I3KE7>75FD;
53>>K 7@7D9;L76 3@6 5AG>6
D7?3;@ 7@7D9;L76 E7H7D3>E75
A@6E38F7DF:7I7>6;@9573E7E
QA@AF FAG5: 7>75FD;53>>K>;H7B3DF AD7>75FDA67
I;F:E=;@ADI7F5>AF:;@9
Q!@EG>3F7KAGDE7>88DA?IAD=3@69DAG@6
Q>I3KEI73D6DK;@EG>3F;@99>AH7E
QA @AF AB7D3F7 I;F: 5AH7DE B3@7>EAD9G3D6E
D7?AH76ADAB7@
---------------------------------------------------------------------
Q-%+ & +++ 53@ 47
63@97DAGE
Q#77BKAGD:736AGFA88G?7E
Q-E7 H7@F;>3F;A@ AD 7J:3GEF FA
D7?AH7 8G?7E 8DA?4D73F:;@9
LA@7
---------------------------------------------------------------------
Q/$!& +(*#+ 53@ 53GE7
8;D7AD7JB>AE;A@
Q#77B8>3??34>7?3F7D;3>3I3K
---------------------------------------------------------------------
*Y*0+53@4GD@
Q/73D 7K7 73D 3@6 4A6K BDAF75
F;A@
---------------------------------------------------------------------
+ !,!'&$ /*&!& !&'*%,!'&
-&**/$!& +,0 (*-,!'&+
&!&, *'&,', !+'(*,!&%&
-$
---------------------------------------------------------------------
/*&!&
+,0(*-,!'&+
* & -&*+,& &,!* +,!'&
'*'(*,!&% !&
!&(-,('/*
'&
'
/!**
('+!,!.'-,(-,
&,!.'-,(-,
!&(-,('/*
!*,-**&,
'(&!*-!,
.'$,
!&(-,.'$,
'-,(-,.'$,
!&(-,-**&,
'-,(-,-**&,
(*',,!.
*'-&
/*&!&'*
-,!'&
-
-
-
!
!
*( ! +0%'$+, ,((*'&
, !+% !&'*!&, !+%&-$
'(*,!'&
$&R(!(
!&!,!'&'/$!&,*%+
/+
• Wire Feed Speed
QConstant Current
.
QConstant Voltage
%/
• Gas Metal Arc welding
+%/
QShielded Metal Arc welding
/
QFlux Core Arc Welding
&*$+*!(,!'&
7@7D3>(:KE;53>7E5D;BF;A@
The LN™-25 PIPE is specially engineered to be the
most rugged portable wire feeder available and meets
the individual welder needs. This model includes a
gas solenoid for flexibility to run most wire processes.
The plastic case is molded from a high impact, flame
retardant plastic for durability and low weight. The
patent pending design keeps the internal components
protected and dry.
The heart of the LN™-25 PIPE is the 2 roll MAX-
TRAC™ drive. The patented features on the wire
drive offer tool-less changing of the drive rolls and
wire guides for quick spool changes. A tachometer
controlled motor powers the patent pending drive rolls
for smooth, steady feeding without slippage.
The LN™-25 PIPE has only two p.c. boards that are
designed to be simple, reliable and easy to service.
7@7D3>G@5F;A@3>7E5D;BF;A@
The LN™-25 PIPE as designed is a simple, robust
feeder. Standard features include a calibrated wire
feed speed dial, 2 step/trigger interlock switch, Gas
Purge and Cold Feed.
*'%%&(*'+++
• GMAW
• FCAW
(*'++$!%!,,!'&+
• GMAW-P procedures must be qualified by the cus-
tomer.
• Across-the-Arc models are not recommended for
stitch or spot welding.
)-!(%&,$!%!,,!'&+
• The duty cycle of the wire feeder is 450A, 60%.
Duty cycle is based upon the amount of welding
performed in a 10 minute period.
• The maximum spool size is 45 lb, 12" diameter.
• Maximum FCAW gun length is 15 ft.
• Maximum GMAW gun length is 25 ft.
• K2330-1 Timer Kits do not work with the feeder.
Use K2330-2 kits.
• Push-pull guns do not work with the wire feeder.
• The digital displays do not show preset voltage
*'%%&('/*+'-*+
• CV-250
• CV-300
• CV-305
• CV-400
• CV-655
• DC-400
• DC-600
• DC-655
• Invertec V-350 PRO
• Invertec V-450 PRO
• Multi-Weld 350
• Ranger 10,000
• Ranger 3 Phase
• Ranger 225
• Ranger 225 GXT
• Ranger 250
• Ranger 250 GXT
• Ranger 305
• SAE-400
• Pipeliner 200G
• Classic 300
• Vantage 300
• Vantage 400
• Vantage 500
• Air Vantage 500
Big Red’s
Eagle 10,000 Plus
Classic’s
%3J;?G?/+
+F3@63D6+B;@
73D;@9
280
340
440
520
600
%;@;?G?D5.A>FE
15 V
17 V
21 V
24 V
27 V
/!*+(#&'
/;D7776+B776.'B7D3F;A@
When Across the Arc models are operated with CV
power sources, the wire feed speed will remain a con-
stant value, independent of arc voltage changes, as
along as the arc voltage does not drop below the val-
ues per the following table.
/;D7776+B776
The 83% wire feed speed reduces the wire feed
speed to 83% of the original set value when activated.
For example, if the original wfs = 200 in/min, the feed-
er will regulate to 0.83 x 200 = 166 in/min.
The 83% trigger requires a gun with a dual procedure
switch.
This feature is often useful when welding pipe, and a
“cooler” procedure is required on the bottom portion.
'(*,!'&
(See GEFA?7DEE;EF3@57(A>;5K in the front of this
Instruction Manual)
+*'&,'&,*'$+ +77;9GD7
!,%+*!(,!'&
1 Wire Feed Speed/Amperage Display
2 Wire Feed Speed LED
3 Amperage LED
4 Wire Feed Speed Knob
5 5 pin gun trigger connector
6 Work Clip Connection
7 Thermal LED
8 Voltage Display
9 Voltage LED
10 Set-up Push Button
$&R(!(
1
5
2
6
7
8
9
10
3
4
!-*
.'(*,!'&
'(*,!'&
$&R(!(
, *%$$%','*'.*$'
The thermal light illuminates when the wire
drive motor draws too much current. If the
thermal light illuminates, the wire drive will
automatically shutdown for up to 30 seconds to allow
the motor to cool. To start welding again, release the
gun trigger, inspect the gun cable, liner (and conduit).
Clean and make repairs as necessary. Start welding
again when the problem has been safely resolved.
For best results, keep the gun cable and conduit as
straight as possible. Perform regular maintenance
and cleaning on the gun liner, conduit and gun.
Always use quality electrode, such as L-50 or L-56
from Lincoln Electric.
('/*-(+)-&
All of the LED’s will briefly illuminate during power-up.
If the gun trigger is activated during power up, the
feeder will not operate until the gun trigger is released.
/!*+(%(*!+($0
!6>7
The left display shows the preset I;D78776 EB776.
The right display shows '.. The wire feed speed
LED is lit.
/7>6;@9
The value in the left display will be either 3?BE or
actual I;D78776EB776, depending upon the selection
chosen in the set-up menu. The corresponding LED
below the display will light. Note that actual WFS may
not match preset WFS, if welding at low voltages with
high wire feed speeds. The right display shows the arc
HA>F397. If the wire feeder is connected for electrode
negative welding, then the voltage display shows a
minus sign.
8F7D/7>6;@9
The display continues to hold the value of the 3?B7D
397 or /+ and 3D5 HA>F397 for five seconds after
welding stops. The 3?B7D397 or /+ and HA>F397
displays flash.
+,-(%&-
(D7B3D3F;A@8AD/+3>;4D3F;A@
• Place the CV/CC switch in CV.
• Set the display to the desired wire feed speed
(example: 400 inches per minute)
• Measure the actual wire feed speed (example: 405
inches per minute)
• Place the WFS knob in the 12 o’clock position.
(D7B3D3F;A@8AD?B7D3973>;4D3F;A@
Connect the feeder to a power source and grid.
Adjust the power source and grid to the desired
amperage. (example: 220 Amps)
Record the amperage display on the wire feeder.
(example: 210 amps)
To enter the set-up menu, use paper clip to press the
small button located on the case front.
AVERTISSEMENT
AV
WFS
AVERTISSEMENT
AV
AMPS
VOLTAGE
BUTTON
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
Lincoln Electric LN-25 Pro Mode d'emploi
- Catégorie
- Système de soudage
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Lincoln Electric Control Box CB-WCS (For Automation) Mode d'emploi
-
-
-
-
-
-
-
-
-
Lincoln Electric INVERTER ARC 120 Manuel utilisateur
