Yamaha GX700 Manuel utilisateur

Marque: Yamaha

Modèle: GX700

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Ce manuel convient également à

GX-700

–

DISC CD CHANGER

STANDBY TIMER

DOWN UP

VOLUME

STANDBY/ON

AUTO REVERSE CASSETTE DECK

DOLBY B NR

PRESET

TUNING

BAND A

DISC

DISC CHANGE OPEN

PROGRAM

B.BOOST

MUSIC

INPUTINPUT

DIRECTION

PUSH OPEN

MINI COMPONENT SYSTEM GX–700

OWNER’S MANUAL

MODE D’EMPLOI

U C A

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and

cart combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to

a wall or ceiling only as recommended by the

manufacturer.

8 Ventilation – The unit should be situated so that its location

or position does not interfere with its proper ventilation. For

example, the unit should not be situated on a bed, sofa,

rug, or similar surface, that may block the ventilation

openings; or placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air

through the ventilation openings.

9 Heat – The unit should be situated away from heat sources

such as radiators, stoves, or other appliances that produce

heat.

10 Power Sources – The unit should be connected to a power

supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged;

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or

exhibits a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating instruc-

tions. All other servicing should be referred to qualified

service personnel.

17 Power Lines – An outdoor antenna should be located away

from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR

MOISTURE.

IMPORTANT

Please record the serial number of this system

in the space below.

Model:

Serial No.:

The serial number is located on the rear of the

main unit.

Retain this Owner’s Manual in a safe place for

future reference.

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to

grounding electrodes, and requirements for the

grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT :

When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to

eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

Unpacking ● After unpacking, check that the following parts are contained.

Déballage ● Après le déballage, vérifier que les pièces suivantes sont incluses.

● Main unit

● Appareil principal

● Remote control

● Télécommande

● Batteries (size AA, UM/SUM-3, R6, HP-7)

● Piles (format AA, UM/SUM-3, R6, HP-7)

● Mounting brackets

● Supports de montage

● Screws

● Vis

● Pads

● Patins

● Front speakers

● Enceintes avant

● Center speaker

● Enceinte centrale

● Rear speakers

● Enceintes arrière

● Speaker cords

● Câbles d’enceintes

● AM loop antenna

● Antenne-cadre AM

● Indoor FM antenna

● Antenne intérieure FM

PROGRAM

BASS

BOOST

MUSIC

CENTER/

REAR/DELAY

TEST

LEVEL

VOLUME

POWER

SLEEP

REC/PAUSE

DIRECTION

TAPE

9 0

TIME PROG R. TIME

EDIT

PRESET

+I0

MODE REPEAT

RANDOM

TUNER

DISC SKIP

TUNER

INPUT

DISC

–

DISC CD CHANGER

STANDBY TIMER

DOWN UP

VOLUME

PUSH OPEN

MINI COMPONENT SYSTEM GX–700

STANDBY/ON

AUTO REVERSE CASSETTE DECK

DOLBY B NR

DIRECTION

PROGRAM B.BOOST

MUSIC

INPUTINPUT

PRESET

TUNING

BAND A

DISC CHANGE OPEN

1 cm 1 cm

20 cm20 cm

20 cm

20 cm 20 cm

20 cm

● Setting this system ● Installation de ce système

English

Set this system allowing enough spaces around and behind the main unit to assure good ventilation. Be sure not to place

another unit or any object on top of the main unit to prevent the ventilation holes from being obstructed. Otherwise, it may

cause fire or damage to the main unit.

Note

When placing the speakers apart from the main unit, be sure to allow a space of at least 20 cm above, behind and on

both sides of the main unit. If the main unit is put in a rack, the front of it must be fully opened.

* The values must be applied to China and Singapore models only.

Français

Installer ce système en laissant assez d’espace autour et derrière l’appareil principal pour assurer une bonne

ventilation. Veiller à ne pas empiler un autre appareil ou un autre objet sur l’appareil principal afin de ne pas boucher

les orifices de ventilation. Sinon, on risquerait de provoquer un incendie ou d’endommager l’appareil principal.

Remarque

Lorsqu’on place les enceintes à une certaine distance de l’appareil principal, veiller à laisser un espace d’au moins 20

cm au-dessus, derrière et sur les deux côtés de l’appareil principal. Si l’on place l’appareil principal dans un meuble,

veiller à ce que le côté avant du meuble soit grand ouvert.

Les valeurs ne doivent être appliquées qu’aux modèles pour la Chine et Singapour.

DISC

–

DISC CD CHANGER

STANDBY TIMER

DOWN UP

VOLUME

STANDBY/ON

AUTO REVERSE CASSETTE DECK

DOLBY B NR

DIRECTION

PROGRAM

B.BOOST

MUSIC

INPUTINPUT

PHONES

MIN

PRESET

TUNING

BAND A

DISC CHANGE OPEN

TREBLEBASS

AUTO/MANUAL

TIMER

MEMORY

TIME ADJ

REC/PAUSEDOLBY NR

HOUR

RANDOM

REPEAT TIME

DISPLAYMODE

]

\ZX[YW

F, S

B, R

A, Q

0, P

LONM

● Front panel ● Panneau avant

1 Display panel

Panneau d’affichage

2 Remote control sensor

Capteur de télécommande

3 TIMER

4 STANDBY [p. 12]

5 B. BOOST [p. 30]

6 PROGRAM [p. 10, 33]

7 PHONES [p. 31]

8 BASS/TREBLE [p. 30]

9 Front cover

Couvercle avant

0 / [p. 18, 19]

A A/B/C/D/E [p. 19]

B PRESET/TUNING/BAND

[p. 18]

C VOLUME [p. 30]

D MUSIC [p. 31]

E INPUT ( / ) [p. 12, 18, 22, 29]

F HOUR [p. 9, 35]

G MIN [p. 9, 35]

H DISPLAY [p. 9, 35]

I MEMORY [p. 19, 20]

TIME ADJ [p. 9]

J STANDBY/ON [p. 10]

K AUTO/MANUAL [p. 18]

TIMER [p. 35]

L Disc tray

Plateau de disque

[p. 12]

M DISC (1, 2, 3) [p. 13]

N DISC CHANGE [p. 13]

O OPEN/CLOSE [p. 12]

P ( )/ ( ) [p. 13]

Q / [p. 12]

R [p. 12]

S RANDOM [p. 15]

T TIME [p. 16]

U REPEAT [p. 15]

V Tray

Plateau

[p. 22]

W MODE [p. 22]

X [p. 22]

Y DIRECTION [p. 22]

Z ( )/ ( ) [p. 23]

[ [p. 22]

\ [p. 22]

] REC/PAUSE [p. 24]

` DOLBY NR [p. 21, 24]

Amplifier/tuner Amplificateur/tuner

CD player Lecteur de disque compact

Tape deck Platine cassette

TUNER → TAPE → CD

AUX/MD

← VCR ← VIDEO

↑

↓

9 0

TIME PROG R. TIME

EDIT

PRESET

+I0

MODE REPEAT

RANDOM

TUNER

DISC SKIP

REC/PAUSE

DIRECTION

CENTER

REAR

DELAY

TEST

PROGRAM

BASS

BOOST

MUSIC

POWER

SLEEP

INPUT

VOLUME

TAPE

TUNER

LEVEL

9 0

TIME PROG R. TIME

EDIT

PRESET

+I0

MODE REPEAT

RANDOM

TUNER

DISC SKIP

TUNER

REC

PAUSE

DIRECTION

CENTER

REAR

DELAY

TEST

PROGRAM

BASS

BOOST

MUSIC

POWER

SLEEP

INPUT

VOLUME

TAPE

LEVEL

KLMNO

UTS

● Remote control ● Telecommande

1 Transmission window

Fenêtre de transmission

[p. 4]

2 Numeric buttons

Touches numériques

[p. 19]

3 A, B, C, D, E [p. 19]

4 TEST [p. 10]

5 CENTER/REAR/DELAY

[p. 33]

F Numeric buttons

Touches numériques

[p. 13]

G TIME [p. 16]

H PROG [p. 14]

6 LEVEL (+/–)

[p. 10, 33]

7 POWER

[p. 10]

8 SLEEP [p. 36]

9 PRESET ( / )

[p. 19]

0 TUNER [p. 18]

A PROGRAM

[p. 10, 33]

I MODE [p. 12]

J DISC SKIP [p. 13]

K REPEAT [p. 15]

L ( )/ ( ) [p. 13]

M RANDOM [p. 15]

N [p. 12]

O [p. 12]

P EDIT [p. 26]

Q R. TIME [p. 26]

R REC/PAUSE [p. 24]

S / [p. 23]

T [p. 22]

U [p. 22]

B MUSIC [p. 31]

C BASS BOOST

[p. 30]

D VOLUME (+/–)

[p. 30]

E INPUT ( / )

[p. 12, 18, 22, 29]

TUNER → TAPE

↑↓

AUX/MD CD

↑↓

VCR ← VIDEO

Amplifier/tuner Amplificateur/tuner

CD player Lecteur de disque compact

Tape deck Platine cassette

V DIRECTION [p. 22]

Contents

English

Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment.

For the best performance, read this manual carefully. It will guide you in operating your YAMAHA product.

Page

SAFETY INSTRUCTIONS

.............................Inside of the Front Cover

Precautions.................................................

Features ......................................................

Preparations and connections..................

Installing batteries in the remote control .................. 4

Remote control operation range ..............................4

Setting up the speakers ...........................................5

Connections .............................................................7

Setting the clock.......................................................9

Adjusting brightness of the display ..........................9

Speaker balance adjustment .................................10

Compact disc player operation................

Basic play...............................................................12

To change the disc play mode ...............................12

To select another disc ............................................ 13

To select the desired track directly ......................... 13

To play the desired track (Skip)..............................13

To advance or reverse play rapidly (Search) .........13

To exchange a disc (or discs) while playing

(PLAYXCHANGE) ..................................................13

Program play..........................................................14

Random play ..........................................................15

Repeat play ............................................................15

Switching the time display......................................16

Tuning operation ......................................

Automatic tuning ....................................................18

Manual tuning ........................................................18

Manual preset tuning .............................................19

Automatic preset tuning .........................................20

Page

Playing back a tape..................................

General information ............................................... 21

Basic operation ...................................................... 22

Winding the tape ....................................................23

Searching for the beginning

of the desired selection ..........................................23

Recording .................................................

Basic recording ...................................................... 24

Recording from CDs utilizing the EDIT function..... 26

Operating the external units connected

with this system .......................................

Various sound control .............................

General sound control............................................ 30

Graphic equalizer...................................................31

Sound field processor ............................................32

Using the built-in timer ............................

Timer play ..............................................................35

Timer recording......................................................36

Sleep timer operation.............................................36

Appendix...................................................

Troubleshooting ..................................................... 37

Specifications.........................................................39

For basic source play, the following illustrations on top of

pages will help you to look for the section you need.

..... CD play ..... Tuning

..... Tape playback/recording

E-1

English

■ To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

■ Choose the installation location of this system carefully.

Avoid placing it in direct sunlight or close to a source of

heat. Also avoid locations subject to vibration and

excessive dust, heat, cold or moisture. Keep it away from

sources of hum such as transformers and electric motors.

■ Do not operate this system upside-down. It may overheat,

possibly causing damage.

■ Never open the cabinet. If something drops into the set,

contact your dealer.

■ The openings on the main unit cover assure proper

ventilation of the main unit. If these openings are

obstructed, the temperature inside the unit will rise rapidly.

Therefore, avoid placing objects against these openings,

and install the main unit in a well-ventilated area to

prevent fire and damage.

■ Always set the VOLUME control to minimum before

starting an audio source play: increase the volume

gradually to an appropriate level after play has started.

■ When not planning to use this system for long periods of

time (ie., vacation, etc.), disconnect the AC power plug

from the wall outlet.

■ Grounding or polarization – Precautions should be taken

so that the grounding or polarization of this system is not

defeated.

■ Do not use force on switches, controls or connection

wires. When moving the main unit, first disconnect the

power plug and the wires connected to other equipment.

Never pull the wire itself.

■ If an external appliance (TV, radio, etc.) interferes with this

system operation, move the main unit away from such an

appliance.

■ Do not attempt to clean this system with chemical

solvents; this might damage the finish. Use a clean, dry

cloth.

■ Be sure to read the “Troubleshooting” section regarding

common operating errors before concluding that this

system is faulty.

■ To prevent lightning damage, disconnect the AC power

plug and the antenna cable when there is an electrical

storm.

■ Do not plug the AC power plug to the wall socket before

you finish all connections.

■ Never allow metallic items (e.g. screwdrivers, tools, etc.) to

come near the tape deck’s record/playback head

assembly. Doing so may not only scratch or damage the

head’s mirror-smooth finish, it may change the magnetic

characteristics of the heads, causing a deterioration in

reproduction performance quality.

■ Although the tape deck’s record/playback heads are high

quality heads with outstanding reproduction

characteristics, they can become dirty through the use of

old tapes or from dust accumulation over time. This can

have a serious effect on reproduction quality. Clean the

heads regularly with one of the commonly available head

cleaners or with cleaning solutions.

■ The voltage to be used must be the same as that specified

on this system. Using this system with a higher voltage

than specified is dangerous and may result in a fire or

other types of accidents causing damage. YAMAHA will

not be held responsible for any damage resulting from use

of this system with a voltage other than specified.

■ The sound level at a given volume setting depends on

speaker location and other factors. Care should be taken

to avoid exposure to sudden high levels of sound, which

may occur when turning on this system with the volume

control setting at high, and to continuous high levels of

sound.

■ Sudden temperature changes and storage or operation in

an extremely humid environment may cause condensation

inside the cabinet. Condensation can cause this system to

malfunction.

To eliminate condensation:

•

CD pickup

Leave the power on with no disc loaded until normal

play becomes possible (about 1 hour).

•

Tape head

Leave the power on with no tape loaded until normal

playback becomes possible (about 1 hour).

Note

If condensation forms on the tape head, dirt or dust

may accumulate during use.

•

Remote control

Wipe off condensation on the transmission window

with a soft cloth before operating this system.

■ To prevent a malfunction of this system:

•

Do not use any non standard shaped disc (heart etc.)

available on the market, because it may damage this

system.

•

Do not use a disc with tape, seals, or paste on it,

because damage to this system may result.

Precautions: Read this before operating your system

This system is not disconnected from the AC power

source as long as it is connected to the wall outlet, even if

this system itself is turned off. This state is called the

standby mode.

In this state, this system is designed to consume a certain

level of power.

Note

Please check the copyright laws in your country to record

from records, compact discs, radio, etc. Recording of

E-2

Precautions: Read this before operating your system

IMPORTANT

Please record the serial number of this system in the space

below.

Model:

Serial No.:

The serial number is located on the rear of the main unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

WARNING

To reduce the risk of fire or electric shock, do not expose this

system to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer

servicing to qualified personnel only.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

As the laser beam used in this system is harmful to the

eyes, do not attempt to disassemble the cabinet. Refer

servicing to qualified personnel only.

This system is classified as a

CLASS 1 LASER product.

The CLASS 1 LASER

PRODUCT label is located on

the rear exterior.

CLASS 1 LASER PRODUCT

Laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

CAUTION FOR CARRYING THE MAIN UNIT

Be sure not to carry or tip the main unit with discs

remaining in it.

CAUTION FOR MOVING THE MAIN UNIT

Before moving the main unit, first remove all discs from

the disc tray and close the tray by pressing the OPEN/

CLOSE button. After you confirm that “NO DISC” lights up

on the display, turn this system into the standby mode by

pressing the STANDBY/ON switch, and then disconnect

the power plug from the AC outlet.

Voltage Selector (China and General models only)

The voltage selector on the rear panel of the main unit

must be set for your local main voltage BEFORE

plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

FREQUENCY STEP switch

(China and General models only)

Because the interstation frequency spacing differs in

different areas, set the FREQUENCY STEP switch (located

at the rear) according to the frequency spacing in your

area.

Be sure to change the setting of this switch with the AC

supply lead of this system disconnected from the AC outlet.

E-3

English

Features

General

●

5-Speaker Multichannel Audio System

(Two front, One Center and Two Rear

Speakers)

●

High Power Output

Front L, R: 80W + 80W (6Ω) RMS, 0.9%

THD, 1 kHz

Center: 80W (6Ω) RMS Output

Power,

0.9% THD, 1 kHz

Rear: 25W (6Ω) RMS Output

Power,

0.9% THD, 1 kHz

● 4 External Audio/Video Component

Connecting Capability

● Multiuse Timer/Sleep Timer

● SUBWOOFER Output for Low Frequency

Expansion

● Remote Control Capability

● BASS BOOST

● 5-Band Spectrum Analyzer

● DOLBY PRO LOGIC and DOLBY 3

STEREO Decoding

● Sound Field Processing

(HALL and YMERSION)

● Test Tone Generator for Easier Speaker

Balance Adjustment

● 3 Preset Graphic Equalizer Modes

(ROCK, POPS and JAZZ)

Compact Disc Player

●

3-Disc Carousel Type CD Changer

● PLAYXCHANGE

Disc changing while playing

● 20-Track Random Access Programming

● Repeat Play for Single Track/Entire Disc/

All Discs

● Random Sequence Play

Tape Deck

● Automatic Synchronized Recording with

● EDIT Function Useful for Recording

CD(s)

●

Automatic Reverse

●

Dolby B Type Noise Reduction System

Tuner

●

40 Station Preset Tuning

●

Automatic Preset Tuning

E-4

SET MD

REC/PAUSE

TAPE

DISC

–

DISC VCD CHANGER

DOWN UP

VOLUME

PUSH OPEN

MINI COMPONENT SYSTEM GX–700

MINIDISC RECORDER

PRESET

TUNING

BAND A

DISC CHANGE OPEN

MODE

–

PTY SEEK

–

START

30°

Preparations and connections

1. Turn the remote control over and remove the battery

compartment cover by pulling it up while pressing the edge

of the cover in the direction of the mark.

2. Insert the batteries (AA, R6, UM-3 type) according to the

polarity markings on the inside of the battery compartment.

3. Attach the battery compartment cover.

Notes

● Remove the batteries if the remote control is not used for an

extended period of time.

● If batteries leak, dispose of them immediately. Avoid

touching the leaked material and contact with clothing, etc.

Clean the battery compartment thoroughly before installing

new batteries.

● Be sure to use the same type of batteries together.

● Do not use a new battery and an old battery together.

Installing batteries in the remote control

Notes

● The area between the remote control and the main unit must

be clear of large obstacles.

● Do not expose the remote control sensor to strong lighting,

in particular, an inverter type fluorescent lamp. Otherwise,

the remote control may not work properly. If necessary,

position the main unit away from direct lighting.

Battery replacement

If you find that the remote control must be used closer to the

main unit, the batteries are weak. Replace both batteries with

new ones.

Remote control operation range

0,2 m – 6 m

(8” – 20’)

E-5

English

Setting up the speakers

m 4 channel 5 speaker configuration

This system employs a 5 speaker configuration: 2 front

speakers, 2 rear paralleled speakers and a center speaker.

The front speakers are used for outputting main source sound.

The rear speakers are for effect and surround sounds when

the sound field program

PRO LOGIC or HALL is selected.

The center speaker is for center sounds (dialog etc.) when the

sound field program PRO LOGIC or 3 STEREO is

selected.

m Placing the speakers

Front speakers: On both sides of the TV and almost the

same height as the TV.

Center speaker: Precisely between the front speakers.

Rear speakers: Behind your listening position, facing

slightly inward. Nearly 1.8 m (approx. six

feet) up from the floor.

Subwoofer: The position of the subwoofer is not so

(separate purchase)

critical because low bass tones are not

highly directional.

m Mounting the center speaker

Place the center speaker on the TV, on the floor under the TV

or in the TV rack so that it is stabilized.

When placing the speaker on top of the TV, to prevent the

speaker from falling down, put the provided pads at four points

on bottom of the speaker.

Preparations and connections

Front L Center Front R

DialogueDialogo

Rear L Rear R

Front L

TV set

Front R

Center

Rear L

Rear R

Subwoofer

E-6

Preparations and connections

m Mounting the rear speakers

Mount the rear speakers on a shelf, rack or on the floor, or

hang them on the wall.

To mount the rear speakers on the wall by using

commercially available speaker stands

The provided mounting bracket has 1 pair of screw holes (at

an interval of 60 mm). They are available for mounting the

speaker on a speaker stand.

* Those screw holes can be used with M4 screws only.

Note

It is recommended that you connect the speaker cords to the

speaker’s terminals before attaching the bracket to the

speaker.

1 Attach the bracket to the bottom of the speaker by using

the provided screw so that the convex part of the bracket

fits in the grooved part of the speaker as figured left.

2 Mount the speaker on the speaker stand by using the

screw holes on the bracket.

To mount the rear speakers on the wall without

using any bracket or stand

If desired, you can hang the speaker on the protruding screws

on the wall without using the bracket.

Fasten screws into a firm wall or wall support as figured left,

and hang the holes of the speaker on the protruding screws.

* Make sure that the screws are caught by a narrow part of

the holes securely.

WARNING:

● Each of the rear speakers weighs 0.8 kg (1 lbs. 12 oz.).

Do not mount them on thin plywood or soft wall

surface material, as the screws may come out of the

flimsy surface, causing the speakers to fall down and

be damaged, or result in personal injury.

● Do not fasten the speakers to the wall with nails,

adhesives, or other unsound hardware. Long-term use

and vibrations may cause them to fall down.

● To avoid accidents resulting from tripping over loose

speaker cords, fix them to the wall.

● Select a proper position on the wall to mount the

speaker and the stand so that no one will hit his head

or forehead on the projections of them, resulting in

personal injury.

60 mm

Mounting

bracket

Screw

Tapping screw

(Available at the

hardware store)

Min.

12 mm

65 mm

Wall or wall

support

E-7

English

Preparations and connections

Never plug the AC supply lead of this system into the AC outlet until all connections are completed.

Connections

Caution

Do not let the bare speaker wires touch each other as this could damage the amplifier and/or speakers.

When connecting a subwoofer (separate purchase)

You may wish to add a subwoofer to reinforce the bass frequencies.

When connecting a subwoofer to this system, connect the SUBWOOFER OUT terminal of this system to the INPUT terminal of the

subwoofer.

* Ordinary subwoofers, including the Yamaha Active Servo Processing Subwoofer System, are designed so that the amplifier and

subwoofer are in the same unit.

* The SUBWOOFER OUT terminal outputs low frequencies from the left front, center and right front channels.

(The cut-off frequency of this terminal is 200 Hz.)

m Connecting speakers

Connect the speakers to the corresponding speaker terminals on the rear of the main unit respectively by using the speaker cords.

Make sure that the polarity of the speaker cords is correct, that is the + and – markings are observed. If these cords are reversed,

the sound will be unnatural and lack bass.

On the main unit

Red: positive (+)

Black: negative (–)

1 Press up the tab.

2 Insert the bare wire.

[Remove approx. 5mm (1/4”)

insulation from the speaker

wires.]

3 Press down the tab and

secure the wire.

On the speakers

Red: positive (+)

Black: negative (–) 1 Press the tab

2 Insert the bare wire.

[Remove approx. 5mm

(1/4”) insulation from

the speaker wires.]

3 Release the tab and

secure the wire.

MAINS

OUT

AUX/MD

VIDEO SIGNAL

MONITOR

OUT

VCR

VIDEO

OUT

SUBWOOFER

SPEAKERS

SEE OWNER’S MANUAL

FOR CONNECTION.

SPEAKERS

CENTER: 6

Ω

MIN./SPEAKER

REAR: I 2

Ω

MIN./SPEAKER

CENTERREAR REAR

R L

Ω

MIN./SPEAKER

FRONT

R L

L R

INPUT

Subwoofer system

(Separate purchase)

Rear speaker

Front speakers

Rear speaker

Center speaker

To AC outlet

(U.S.A model)

E-8

Preparations and connections

m Connecting external components

This system can be connected with external audio and video

components. Make connections between this system and the

components using RCA pin plug connector cables correctly,

that is to say L (left) to L and R (right) to R. Also, refer to the

owner’s manual for the component to be connected to this

system.

* A digital-to-digital recording is possible from a CD played on

the built-in CD player to an MD (or tape) on an external MD

recorder (or DAT) by connecting the DIGITAL OUT

(OPTICAL) terminal on the rear of the main unit to the MD

recorder (or DAT).

m Antenna connection

(1) Supplied FM antenna

Connect the FM antenna wire to the corresponding terminal

and direct the FM antenna wire to the direction where the

strongest signal can be received.

(2) Supplied AM loop antenna

Connect the AM loop antenna wires to the corresponding

terminals. Position the AM loop antenna for optimum

reception.

Notes

● When static is still heard even after adjusting the position of

the AM loop antenna, try reversing the wire connections

(from the right terminal to the left one, and vice versa).

● The AM loop antenna should be placed apart from the main

unit. The antenna may be hung on a wall.

Using an external antenna

● Use an external FM antenna instead of an indoor FM

antenna if you need better reception. Consult your dealer.

● Use an external AM antenna if you need better reception.

Consult your dealer.

(1)

(2)

ANTENNA

75Ω UNBAL.

FM GND AM

ANTENNA

75Ω UNBAL.

FM GND AM

DIGITAL OUT

OPTICAL

ANTENNA

75Ω UNBAL.

FM GND AM

DIGITAL OUT

OPTICAL

OUT

AUX/MD

VIDEO SIGNAL

MONITOR

OUT

VCR

VIDEO

OUT

SUBWOOFER

SPEAKERS

SEE OWNER’S

FOR CONNECTI

CENTER: 6

Ω

MIN./

REAR: I 2

Ω

MIN./

CENTERREAR

FRONT

TV monitor

VCR

LD/DVD player, etc.

MD recorder, etc.

(U.S.A. model)

English

E-9

DISC

–

DISC CD CHANGER

STANDBY TIMER

DOWN UP

VOLUME

STANDBY/ON

AUTO REVERSE CASSETTE DECK

DOLBY B NR

DIRECTION

PROGRAM

B.BOOST

MUSIC

INPUTINPUT

PHONES

MIN

PRESET

TUNING

BAND A

DISC CHANGE OPEN

TREBLEBASS

AUTO/MANUAL

TIMER

MEMORY

TIME ADJ

REC/PAUSEDOLBY NR

HOUR

RANDOM

REPEAT TIME

DISPLAYMODE

RANDOM

REPEAT

HOUR

MIN

RANDOM

REPEAT

HOUR

MIN

DISPLAY

MEMORY

TIME ADJ

MEMORY

TIME ADJ

DISC

DOWN UP

VOLUME

STANDBY/ON

PROGRAM

B.BOOST

MUSIC

INPUTINPUT

MIN

PRESET

TUNING

BAND A

DISC CHANGE OPEN

AUTO/MANUAL

TIMER

MEMORY

TIME ADJ

REC/PAUSEDOLBY NR

HOUR

RANDOM

REPEAT TIME

DISPLAYMODE

1 While the power is on, press DISPLAY to display the time.

2 While holding TIME ADJ pressed, press HOUR and set the

hour.

* Press HOUR once to advance the time by 1hour. Press

and hold to advance continuously.

3 While holding TIME ADJ pressed, press MIN and set the

minute.

* Press MIN once to advance the time by 1

minute. Press and hold to advance continuously.

* The hour setting will not advance even if minute is

advanced from “59” to “00”.

Australia model use a 24-hour display. U.S.A. and Canada

models use a 12-hour display. For China and General

models, either the 24-hour display or the 12-hour display

[shown by “AM (PM) 12:00”] is selected depending on the

setting of the FREQUENCY STEP switch on the rear

panel, so you cannot select the desired type freely.

Note

In the event of a power failure or when the AC supply lead is

disconnected, the time display will go out, however, the clock

will function for about 5 minutes without any power supply.

Otherwise, the time display will flash on and off to indicate that

the time must be reset.

If desired, you can adjust the brightness of the display.

Press and hold DISPLAY for more than 2 seconds so that

“DIMMER ±0” appears on the display.

While holding DISPLAY pressed, turn VOLUME clockwise to

increase or counterclockwise to decrease brightness.

Control range: ±0 to –6 (Preset value: ±0)

Setting the clock

Adjusting brightness of the display

Changes.

Preparations and connections

VOLUME

DISPLAY

E-10

Preparations and connections

1 Turn on the power.

2 Turn down the volume to minimum.

3 Press PROGRAM once or more until “ PRO LOGIC”

lights up on the sound field program indicator.

4 Press TEST.

* “TEST” flashes on and off on the display.

5 Press VOLUME + (up) to increase the volume.

You will hear a test tone (like pink noise) from the left front

speaker, the center speaker, the right front speaker, and

then the rear speakers, for about 2.5 seconds each. The

display changes as shown below.

* The test tone from the left rear speaker and the right rear

speaker will be heard at the same time.

6 Press LEVEL +/– to adjust the sound output levels of the

center speaker and the rear speakers so that the level

becomes almost as same as that of the front speakers.

ex.)

7 When the adjustments are finished, press TEST to cancel

the test tone.

* “TEST” disappears from the display.

Note

Once you have completed these adjustments, you can adjust

whole sound level on your audio system by using VOLUME on

the main unit (or the remote control).

Speaker balance adjustment

You can adjust the sound output level balance between the front, center, and rear speakers using the built-in test tone generator.

This is important for the best performance of the built-in Dolby Pro Logic surround decoder.

The adjustment of each speaker output level should be done at your listening position with the remote control. Otherwise,

the result may not be satisfactory.

PROGRAMMUSIC

TEST

PRO LOGIC

PROGRAM

BASS

BOOST

MUSIC

CENTER/

REAR/DELAY

TEST

LEVEL

VOLUME

POWER

SLEEP

REC/PAUSE

DIRECTION

TAPE

9 0

TIME PROG R. TIME

EDIT

PRESET

MODE REPEAT

RANDOM

TUNER

DISC SKIP

TUNER

INPUT

2, 5

4, 7

Changes.

La page charge ...

Yamaha GX700 Manuel utilisateur

Marque: Yamaha

Modèle: GX700

Catégorie: Lecteur CD

Taper: Manuel utilisateur

Ce manuel convient également à

GX-700

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha GX700 Manuale utente
English: Yamaha GX700 User manual
español: Yamaha GX700 Manual de usuario
Deutsch: Yamaha GX700 Benutzerhandbuch
русский: Yamaha GX700 Руководство пользователя
Nederlands: Yamaha GX700 Handleiding
português: Yamaha GX700 Manual do usuário
dansk: Yamaha GX700 Brugermanual
polski: Yamaha GX700 Instrukcja obsługi
čeština: Yamaha GX700 Uživatelský manuál
svenska: Yamaha GX700 Användarmanual
Türkçe: Yamaha GX700 Kullanım kılavuzu
suomi: Yamaha GX700 Ohjekirja
română: Yamaha GX700 Manual de utilizare

Yamaha GX700 Manuel utilisateur

Ce manuel convient également à

Yamaha GX700 Manuel utilisateur

dans d''autres langues

Documents connexes