Hotpoint LFFA+ 8M14 EU Le manuel du propriétaire
- Catégorie
- Lave-vaisselle
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
1
Operating instructions
Contents
Installation, 2-3
Positioning and levelling
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Ecodesign Regulation
Description of the appliance, 4
Overall view
Control panel
Loading the racks, 5
Lower rack
Cutlery basket
Upper rack
Start-up and use, 6-7
Starting the dishwasher
Measuring out the detergent
Wash options
Wash cycles, 8
Table of wash cycles
Rinse aid and refined salt, 9
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions, advice and Assistance,11
General safety
Disposal
Saving energy and respecting the environment
Assistance
Troubleshooting, 12
English,1
EN
DISHWASHER
LFFA+ 8M14
ES
PT
Español, 49 Português, 61
FR
DE
NL
Français, 13 Deutsch, 25
Nederland,37
Ελληνικά, 73
EL
EN
2
Installation
Keep this instruction manual in a safe place for future
reference. If the appliance is sold, given away or moved, please
ensure the manual is kept with the machine, so that the new
owner may benefit from the advice contained within it.
Please read this instruction manual carefully: it contains
important information regarding the safe installation, use and
maintenance of the appliance.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
This appliance is intended to be used in household and
similar applications such as:
- staff kitchen areas in shops, offices and other working
environments;
- farm houses;
- by clients in hotels, motels and other residential type
environments;
- bed and breakfast type environments.
Positioning and levelling
1. Remove the appliance from all packaging and check that it
has not been damaged during transportation.
If it has been damaged, contact the retailer and do not proceed
any further with the installation process.
2. Check the dishwasher by placing it so that its sides or back
panel are in contact with the adjacent cabinets or even with the
wall. This appliance can also be recessed under a single
worktop
* (
see the Assembly instruction sheet
).
3. Position the dishwasher on a level and sturdy floor. If the floor
is uneven, the front feet of the appliance may be adjusted until it
reaches a horizontal position. If the appliance is levelled correctly,
it will be more stable and much less likely to move or cause
vibrations and noise while it is operating.
4
*. Adjust the height of the rear foot from the front of the appliance
on the central lower part of the dishwasher, turning a hexagonal
spanner (red color) with an opening of 8 mm in a clockwise
direction to increase the height or in an anticlockwise direction to
decrease the height.
Connecting the water and electricity
supplies
Connection to the water and electricity supplies should only
be performed by a qualified technician.
The dishwasher should not stand on top of the water hoses
or the electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Do not use old hoses.
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
Connecting the water inlet hose
• To a suitable cold water connection point: before attaching the
hose, run the water until it is perfectly clear so that any impurities
that may be present in the water do not clog the appliance;
after performing this operation, screw the inlet hose tightly
onto a tap with a ¾ gas threaded connection.
• To a suitable hot water connection point: your dishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
does not exceed a temperature of 60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician (
see Assistance
).
The water pressure must be within the values indicated in the
Technical data table (
see adjacent information
).
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to 80
cm from the floor / surface where the dishwasher rests (A).
Before connecting the water outlet hose to the sink drain,
remove the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device
New Acqua Stop
*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut as it
contains live electrical parts.
* Only available in selected models.
EN
3
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
• The socket is earthed and complies with current regulations.
• The socket can withstand the maximum load of the appliance,
which is indicated on the data plate located on the inside of the
door (
see chapter entitled Description of the appliance
).
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance. If this
is not the case, ask an authorised technician to replace the
plug (
see Assistance
); do not use extension cables or multiple
sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order to
prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any incidents
that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before running
the first wash cycle, completely fill the salt dispenser with water
and add only then approximately 1 kg of salt (
see chapter entitled
Rinse aid and refined salt
). The water may overflow: this is normal
and is not a cause for concern. Select the water hardness value
(
see chapter entitled Rinse aid and refined salt
). - After the salt
has been poured into the machine, the LOW SALT indicator
light
* switches off.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 14 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage
See appliance data plate
Total absorbed
power
See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Labelling)
-2002/96/EC Waste Electrical
and Electronic Equipment
(WEEE)
ECODESIGN REGULATION
ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal
soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even
further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
** Data is obtained by recording values when the appliance is operational and loaded with user crockery.
Standard conditions* User conditions**
Energy consumption
(kWh/cycle)
Water consumption
(l/cycle)
Duration
(min/cycle)
Energy consumption
(kWh/cycle)
Water consumption
(l/cycle)
Duration
(min/cycle)
INTENSIVE
1,65 16 150 1,45 15 135
NORMAL
1,35 16 120 1,20 15 110
EN
4
Overall view
Description of the appliance
1. Upper rack
2. Upper sprayer arm
3. Tip-up compartments
4. Rack height adjuster
5. Lower rack
6. Lower sprayer arm
7. Cutlery basket
8. Washing filter
9. Salt dispenser
10. Detergent and rinse aid dispensers
11. Data plate
12. Control Panel
***
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Control panel
ON/OFF
indicator light
Select wash
cycle button
Low rinse aid
indicator light*
Extra Dry option
button and
indicator light*
Low salt
indicator light*
Time remaining
light-up display
Start/Pause button
and indicator light
ON/OFF/Reset
button
Delayed start button
and indicator light*
Half load button
and indicator light*
Multi-functional tablets
button and indicator light*
Wash cycle
indicator lights
End indicator
light
Drying
indicator light
Washing
indicator light
EN
5
Loading the racks
* Only available in selected models. The number and position
may vary.
Before loading the racks, remove all food residue from
crockery and empty liquids from glasses and cups.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
Lower rack and cutlery basket
The lower rack can hold pans, lids, plates, salad bowls, cutlery, etc.
Large plates and lids should ideally be placed at the sides of the rack.
Several dishwasher models are fitted with tip-up sections
*, which
can be used in a vertical position when arranging plates or in a
horizontal position when arranging saucepans, salad bowls and
frying pans.
The type of cutlery basket may vary (modular or non-modular)
according to the dishwasher model. The non-modular basket
must only
be positioned at the front of the lower rack.
Both are fitted with
grilles over the
top, for improved
cutlery arrange-
ment.
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards, or
they must be positioned horizontally in the tip-up
compartments on the upper rack.
Upper rack
Load this rack with delicate and lightweight crockery: glasses,
cups, saucers and shallow salad bowls.
Adjustable position tip-up compartments
The tip-up compartments
can be positioned at
different heights, to optimise
the arrangement of
crockery throughout the
rack. Wine glasses can be
placed safely in the tip-up
compartments, by inserting
the stem of each glass into
the corresponding slots.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower level.
The height of the upper rack should ideally be adjusted
WHEN THE RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
Open the left and right guide rail stops
and pull out the rack; position it higher or
lower as required, slide it along the guide
rails until the front wheels are in place and
close the stops (
see figure
).
If the rack is fitted with Dual Space
handles
* (
see figure
), pull out the upper
rack until it reaches its stop point, grip
the handles at the sides of the rack and
move it upwards or downwards, then
slowly let it fall back into place.
Items that should not be washed in the dishwasher
• Wooden items, objects with wooden or horn handles or glued-
on parts.
• Items made from aluminium, copper, brass, pewter or tin.
• Items made from plastic material which is not heat-resistant.
• Antique or hand-painted porcelain.
• Antique silver. Silver that is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
We recommend the use of crockery which is dishwasher
safe.
EN
6
Start-up and use
Starting the dishwasher
1. Turn the water tap on.
2. Premere il tasto ON-OFF: si sente un breve bip, tutte le spie e
il display si illuminano per alcuni secondi.
2. Press the ON/OFF button: you will hear a short beep; all the
indicator lights and the display will light up for a few seconds.
3. Open the door and pour in a suitable amount of detergent (
see
below
).
4. Load the racks (
see Loading the racks
) and shut the door.
5. Select the wash cycle in accordance with the type of crockery
and its soil level (
see Table of wash cycles
) by pressing the P
button.
6. Select the wash options
* (
see adjacent information
).
7. Start the cycle by pressing the Start/Pause button: a long
beep signals the start of the wash cycle, the washing cycle
indicator light switches on and the time remaining until the end of
the cycle is displayed.
8. Two short beeps and one long one indicate the end of the
wash cycle; the wash cycle indicator light flashes and the END
indicator light switches on (
fixed light
). Switch off the appliance
by pressing the ON/OFF button, shut off the water valve and
unplug the appliance from the electricity socket.
9. Wait for a few minutes before removing the crockery, in order
to avoid burns. Unload the racks, beginning with the lower level.
- The machine will switch off automatically
during certain periods of inactivity, in order to
minimise electricity consumption.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection process
it is possible to change the cycle, provided that it has only just
begun: once the wash cycle has started, switch off the machine
by pressing and holding the ON/OFF/Reset button. Switch it
back on using the same button and select the desired wash
cycle and options.
Adding extra crockery
Press the Start/Pause button (the corresponding indicator light
will flash). Open the door, taking care to avoid the escaping
steam, and place the crockery inside the appliance. Press the
Start/Pause button (fixed light): the cycle will restart after a
prolonged beep is emitted.
If the Start/Pause button is pressed so as to pause the
machine, the wash cycle or the Delayed Start function (if
selected) is interrupted.
At this stage it is not possible to change the wash cycle.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. It starts again from the point at which it was
interrupted once the door has been shut or once the electricity
supply is restored.
Measuring out the detergent
A good wash result also depends on the correct
amount of detergent being used; exceeding the
stated amount does not result in a more effective
wash and increases environmental pollution.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle
has ended.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid liquid
and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
1. Open cover C by pressing button
D.
2. Pour in the detergent after consulting
the
Table of wash cycles
:
• For powder detergent use
compartments A and B.
• For detergent in tablet form: when
the cycle requires 1 tablet, place it in
compartment A and close the cover;
when it requires 2, place the second tablet at the bottom of the
appliance.
3. Remove detergent residues from the edges of the compartment
and close the cover until it clicks.
A
B
D
C
* Only available in selected models.
EN
7
Multi-functional tablets (Tabs)
This option optimises washing and drying results.
When using multi-functional tablets, press the MULTI-
FUNCTIONAL TABLETS button. The corresponding indicator
light will illuminate. The “Multi-functional tablets” option results
in the lengthening of the wash cycle.
The MULTI-FUNCTIONAL TABLETS option remains
set for subsequent wash cycles if it is not deselected.
The use of tablets is only recommended for models
which offer the MULTI-FUNCTIONAL TABLETS option.
This option is not recommended for use with wash
cycles which do not specify the use of multi-functional
tablets
(
see Table of options
).
* Only available in selected models.
Half load using the upper rack
If there are not many dishes to be washed, a half load cycle may
be used in order to save water, electricity and detergent. Select
the wash cycle and press the HALF LOAD button: the indicator
light will illuminate and the wash cycle will take place only in the
upper rack.
Remember to load the upper rack only, and to reduce
the amount of detergent accordingly.
It is better to use powder detergent in this case.
This option is not compatible with the following wash
cycles: Speed and Baby.
Delayed start
It is possible to delay the start time of the cycle for a period of
time between 1 and 24 hours.
1. After selecting the desired wash cycle and any other options,
press the DELAYED START button: the corresponding indicator
light will illuminate. Use the same button to select the time at which
you wish the wash cycle to begin (after a period of 1 to 24 hours).
2. Confirm your selection using the Start/Pause button; the
countdown will begin. The selected delay period indicator light
flashes and the Start/Pause button stops flashing (the light
becomes fixed instead).
3. When the set time has elapsed, a long beep sounds, the
DELAYED START indicator light switches off and the wash cycle
begins.
To deselect the DELAYED START option, press the DELAYED
START button repeatedly until the text OFF appears.
The Delayed Start function cannot be set once the wash
has been started.
Wash options*
The OPTIONS may only be set, modified or reset after the
wash cycle has been selected and before the Start/Pause
button has been pressed.
Only the options which are compatible with the type of wash cycle
set may be selected. If an option is not compatible with the se-
lected wash cycle (
see Table of wash cycles
), the corresponding
LED flashes rapidly 3 times and 2 short beeps will sound.
If an option is selected which is incompatible with another (previ-
ously selected) option, the indicator light corresponding to the
option selected first will flash 3 times, 3 beeps will sound and it will
be deselected, while the most recently selected option will remain
active.
To deselect an option which has been set by mistake, press the
corresponding button again.
Extra drying*
To improve the dryness level of the crockery, press the EXTRA
DRYING button; the indicator light will illuminate. If it is pressed
again the option will be deselected.
The EXTRA DRYING option increases the duration of
the wash cycle.
A B C D
Table of options
Delayed
Start
Half
Load
Tabs
Extra
Dry
Eco
Yes
Yes
Yes
Yes
Normal
Yes
Yes
Yes
Yes
Daily A 60
Yes
Yes
Yes
No
Soak
Yes
Yes
No
No
Intensive
Yes
Yes
Yes
Yes
Speed 25’
Yes
No
Yes
No
Crystal
Yes
Yes
Yes
Yes
Baby wash
Yes
No
No
No
EN
8
Wash cycles
For available OPTIONS please refer to the Table of options on the Start-up and use page.
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher,
reduce the amount of detergent used accordingly.
The number and type of wash cycles and options may vary depending on the dishwasher model.
Detergent
(A) = compartment A
(B) = compartment B
Wash cycle selection
instructions
Wash cycle
Powder Liquid Tablets
Wash
cycles
which
include
drying
Options
Wash cycle
duration
(tolerance
±10%)
Hrs. Min.
Environmentally-friendly wash cycle
with low energy consumption levels,
suitable for pans and dishes.
Eco
*
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Yes
A–B-C-D
2:55’
Normally soiled pans and dishes.
Standard daily wash cycle.
Normal
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Yes
A–B–C-D
1:50’
Limited quantity of daily soiling.
(4 place settings + 1 saucepan +1
frying pan).
Daily A 60
25 g (A)
25 ml (A)
1 (A)
No
A–B– C
1:00’
Pre-wash for dishes while awaiting
completion of the load with the
dishes from the next meal.
Soak
No
No
No
No
A – B
0:08’
Heavily soiled dishes and pans (not
to be used for delicate items).
Intensive
35 g (A)
35 ml (A)
1 (A)
Yes
A–B–C-D
2:25’
Economic and fast wash to be used
for lightly soiled dishes. (Run cycle
immediately after use) (2 plates + 2
glasses + 4 pieces of cutlery + 1
saucepan + 1 small frying pan).
25 g (A)
25 ml (A)
1 (A)
No
A - C
0:25’
Economic and fast wash for
delicate items which are sensitive to
high temperatures. (Run cycle
immediately after use) (glasses
upper rack + delicate plates, lower
rack). Crystal
35 g (A)
35 ml (A)
1 (A)
Yes
A–B–C-D
1:30’
Disinfecting wash cycle suitable for
washing bottles, rings and teats
together with plates, cups, glasses
and cutlery. The crockery should
only be loaded on the upper rack.
Baby Wash
20 g (A)
20 ml (A)
No
Yes
A
1:20'
Notes:
Optimum performance levels when using the "Daily wash" and "Speed wash" cycles can be achieved by observing the maximum
amounts of crockery specified.
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 grams of powder = approximately 15 ml of liquid - 1 teaspoon = 5 grams of powder = approximately 5 ml of
liquid
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less
energy and is less harmful to the environment.
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following
address: [email protected]
EN
9
Rinse aid and refined salt
G
F
Only use products which have been specifically designed
for dishwashers.
Do not use table salt or industrial salt, or washing up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
rinse aid; however, we recommend that you add salt, especially
if you live in an area where the water is hard or very hard.
Follow the instructions given on the packaging.
If you do not add salt or rinse aid, the LOW SALT
* and
LOW RINSE AID
* indicator lights remain lit.
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs
off surfaces more readily and therefore does not leave streaks or
marks.
The rinse aid dispenser should be filled:
• When the LOW RINSE AID
* indicator light on the control
panel is illuminated;
1. Open the dispenser by turning the
lid (G) in an anticlockwise direction.
2. Pour in the rinse aid, making sure it
does not overflow from the dispenser.
If this happens, clean the spill
immediately with a dry cloth.
3. Screw the lid back on.
NEVER pour the rinse aid directly
into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver to
turn the dosage adjuster (F) to one of the 6 pre-set positions (the
default position is set to 4):
• If there are streaks on the crockery, set the adjustment device
to a lower number (1-3).
• If drops of water remain on the crockery or if there are limescale
marks present after the cycle has finished, set the adjuster to a
higher number (4-6).
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash the
crockery.
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the water
hardness level in your area. This information can be obtained
from the organisation which supplies your household with water.
The water hardness adjustment procedure may vary
depending on the dishwasher model purchased.
- Switch on the appliance by pressing the ON/OFF button.
- Press and hold the P button for a few seconds; after a short
beep sounds, the water hardness setting will appear on the
display and the Start/Pause button will begin to flash (the default
water softening system setting is level
33
33
3).
- Press the P button repeatedly until the desired hardness level
has been reached (1-2-3-4-5
*
see Water hardness table
). The
selected water hardness value will appear on the display.
E.g.: hardness setting 1 ("1" appears on the display);
hardness setting 2 ("2" appears on the display);
hardness setting 3 ("3" appears on the display); etc., etc. up to a
maximum of level 5.
To exit the function, wait a few seconds or press one of the
option buttons
*, or switch off the machine using the ON/OFF
button.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees - mmol/l = millimoles per litre)
Measuring out the refined salt
In order to achieve the best possible results using a wash cycle,
make sure that the dispenser is never empty. Refined salt removes
limescale from the water, thus avoiding the formation of deposits
on crockery.
The salt dispenser is located in the lower part of the dishwasher
(
see Description
) and should be filled:
• When the green float
* cannot be seen by simply looking at the
cap of the salt dispenser.
• When the LOW SALT* indicator light on the control panel is
illuminated;
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. The first time you do this: fill the water tank
right up to its edge.
3. Position the funnel
* (
see figure)
and fill
the salt container right up to its edge (this
should hold approximately 1 kg); it is not unusual for a little water
to leak out.
4. Remove the funnel* and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it on,
the head facing downwards so as to let the water flow out of the
four cracks which are arranged in a star shape on the lower part
of the cap. (the container cap with the green float*)
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash cycle (this could
damage the water softener beyond repair).
When necessary, measure out the salt before a wash cycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
Water Hardness Table
Average salt container
capacity duration
**
Level
°dH
°fH
mmol/l
months
1 0 - 6 0 - 10 0 - 1
7 months
2 6 - 11 11 - 20 1,1 - 2
5 months
3 12 - 17 21 - 30 2,1 - 3
3 months
4 17 - 34 31 - 60 3,1 - 6
2 months
5
*
34 - 50
61 - 90
6,1 - 9
2/3 weeks
For values between 0°f and 10°f, we do not recommend the
use of salt
. *
this setting may cause a slight increase in the
duration of
the cycles.
**
for 1 wash cycle per day.
EN
10
Care and maintenance
Shutting off the water and electricity
supplies
• Turn off the water tap after every wash cycle to avoid
leaks.
• Always unplug the appliance when cleaning it and when
performing maintenance work.
Cleaning the dishwasher
• The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth which
has been dampened with water. Do not use solvents or
abrasive products.
• Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a little
vinegar.
Preventing unpleasant odours
• Always keep the door of the appliance ajar in order to
avoid moisture from forming and being trapped inside
the machine.
• Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is the
main cause behind the formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that the arms are checked from time to time
and cleaned with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer
arm, rotate the locking ring in an
anti-clockwise direction.
The upper sprayer arm should be
replaced with the holes facing
upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it is
clear and free of impurities before performing the necessary
connections. If this precaution is not taken, the water inlet
could become blocked and damage the dishwasher.
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter
and clean it carefully under running water.
- Replace the filter and screw the water hose back into
position.
Cleaning the filters
The filter assembly consists of three filters which remove
food residues from the washing water and then recirculate
the water. They should be cleaned if you wish to achieve
the best results in every wash.
Clean the filters regularly.
The dishwasher should not be used without filters, or if
the filter is loose.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water, using
a non-metallic brush and following the instructions below:
1.1.
1.1.
1. Turn the cylindrical filter C in an anti-clockwise direction
and pull it out (fig. 1).
2.2.
2.2.
2. Remove the cup filter B by exerting a slight pressure on
the side flaps (fig. 2).
3.3.
3.3.
3. Slide out the stainless steel plate filter A (fig. 3).
4.
Inspect the trap and remove any food residue.
NEVER REMOVE the wash cycle pump (black
detail)
(fig. 4)
.
After cleaning the filters, replace the filter assembly and fix
it in position correctly; this is essential for maintaining the
efficient operation of the dishwasher.
Leaving the machine unused for
extended periods
• Disconnect the appliance from the electricity supply and
shut off the water tap.
• Leave the door of the appliance ajar.
• When you return, run a wash cycle when the dishwasher
is empty.
* Only available in selected models.
2
C
B
4
1
3
EN
11
Precautions, advice
and Assistance
This appliance was designed and manufactured in
compliance with current international safety standards. The
following information has been provided for safety reasons and
should therefore be read carefully.
General safety
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
• The appliance was designed for domestic use inside the home
and is not intended for commercial or industrial use.
• The appliance must be used by adults only, to wash domestic
crockery in accordance with the instructions in this manual.
• The appliance must not be installed outdoors, even in covered
areas. It is extremely dangerous to leave the machine exposed
to rain and storms.
• Do not touch the appliance when barefoot.
• When unplugging the appliance always pull the plug from the
mains socket, do not pull on the cable.
• The water supply tap must be shut off and the plug should be
removed from the electrical socket before cleaning the
appliance or carrying out any maintenance work.
• If the appliance breaks down, do not under any circumstances
touch the internal parts in an attempt to perform the repair
work yourself.
• Never touch the heating element.
• Do not lean or sit on the open door of the appliance: this may
cause the appliance to overturn.
• The door should not be left open as it may create a dangerous
obstacle.
• Keep detergent and rinse aid out of reach of children.
• The packaging material should not be used as a toy.
Disposal
• Disposal of packaging materials: observe local legislation so
that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste Electrical
and Electronic Equipment (WEEE) states that household
appliances should not be disposed of using the normal solid
urban waste cycle. Exhausted appliances should be collected
separately in order to optimise the cost of re-using and
recycling the materials inside the machine, while preventing
potential damage to the atmosphere and to public health. The
crossed-out dustbin is marked on all products to remind the
owner of their obligations regarding separated waste
collection.
For further information relating to the correct disposal of
household appliances, owners may contact the relevant public
authority or the local appliance dealer.
Saving energy and respecting the
environment
Saving water and energy
• Only begin a wash cycle when the dishwasher is full. While
waiting for the dishwasher to be filled, prevent unpleasant
odours using the Soak cycle (
see Wash cycles
).
• Select a wash cycle which is suited to the type of crockery
and to the soil level of the crockery using the
Table of wash
cycles
:
- For dishes with a normal soil level, use the Eco wash cycle,
which guarantees low energy and water consumption levels.
- If the load is smaller than usual activate the Half load option
*
(
see Start-up and use
).
• If your electricity supply contract gives details of electricity
saving time bands, run wash cycles during the periods when
a lower tariff is applied. The Delayed start* button (
see Start-
up and use
) helps you organise the wash cycles accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
• We strongly recommend that you use detergents that do not
contain phosphates or chlorine, as these products are harmful
to the environment.
• Enzymes provide a particularly effective action at temperatures
around 50°C, and as a result detergents containing enzymes
can be used in conjunction with low-temperature wash cycles
in order to achieve the same results as a normal 65°C wash
cycle.
• To avoid wasting detergent, use the product in appropriate
quantities based on the manufacturer’s recommendations, the
hardness of the water and the soil level and quantity of crockery
to be washed. Even if they are biodegradable, detergents
contain substances which may alter the balance of nature.
Assistance
Before contacting Assistance:
• Check whether the problem can be resolved using the
Troubleshooting guide (
see Troubleshooting
).
• Restart the programme to check whether the problem has
ceased to exist.
• If the problem persists, contact the Authorised Technical
Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
• The type of malfunction.
• The appliance model (Mod.).
• The serial number (S/N).
This information can be found on the appliance data plate (
see
Description of the appliance
).
* Only available in selected models.
EN
12
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.
Problem:
Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled
• Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and reset the program.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close • The lock was released. Strongly push the door until a “clacking” noise is heard.
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes excessive
noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up and
use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to the hardness
of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
streaked or have a bluish tinge.
• The rinse aid dosage is too high.
The crockery has not been dried
properly.
• A wash cycle without a drying program has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).
• The rinse aid dispenser setting is not suitable.
• The crockery is made from non-stick material or plastic.
The dishes are not clean. • The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up and
use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take any
water in - Tap shut-off alarm
(The ON/OFF indicator light flashes and
the display shows A 6).
• There is no water in the mains supply.
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when the
beeps sounded.
Switch off the appliance using the ON/OFF button, turn on the tap and switch the
appliance back on after 20 seconds by pressing the same button. Re-program the
appliance and restart the wash cycle.
Water inlet hose alarm / Water inlet
filter blocked
(the ON/OFF indicator light flashes and
the display shows A 7).
• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap to
eliminate the risk of flooding and remove the plug from the electrical socket.
Make sure the water inlet filter has not become blocked by impurities (see “Care
and maintenance” chapter).
FR
13
Mode d’emploi
Sommaire
Installation, 14-15
Mise en place et mise à niveau
Raccordements eau et électricité
Conseils pour le premier lavage
Caractéristiques techniques
Ecodesign Regulation
Description de l’appareil, 16
Vue d’ensemble
Tableau de bord
Charger les paniers, 17
Panier inférieur
Panier à couverts
Panier supérieur
Mise en marche et utilisation, 18-19
Mettre en marche le lave-vaisselle
Charger le produit de lavage
Options de lavage
Programmes, 20
Tableau des programmes
Produit de rinçage et sel régénérant, 21
Charger le produit de rinçage
Charger le sel régénérant
Entretien et soin, 22
Coupure de l’arrivée d’eau et de courant
Nettoyer le lave-vaisselle
Eviter les mauvaises odeurs
Nettoyer les bras de lavage
Nettoyage du filtre d’entrée d’eau
Nettoyer les filtres
En cas d’absence pendant de longues périodes
Précautions conseils et Service, 23
Sécurité générale
Mise au rebut
Economies et respect de l’environnement
Service
Anomalies et remèdes, 24
Français, 13
FR
LFFA+ 8M14
LAVE-VAISSELLE
FR
14
Installation
Conserver ce mode d’emploi pour pouvoir le consulter à tout
moment. En cas de vente, de cession ou de déménagement,
s’assurer qu’il accompagne bien l’appareil.
Lire attentivement les instructions: elles contiennent des
conseils importants sur l’installation, l’utilisation et la sécurité de
l’appareil.
En cas de déménagement, transporter l’appareil
verticalement; si besoin est, l’incliner sur le dos.
Cet appareil est conçu pour un usage domestique ou autres
applications similaires, telles que :
- lieux aménagés en espace cuisine pour le personnel de
magasins, bureaux et autres lieux de travail ;
- fermes ;
- utilisation par les clients d'hôtels, de motels ou autres locaux de
type résidentiel ;
- chambres d'hôtes.
Mise en place et mise à niveau
1. Déballer l’appareil et s’assurer qu’il n’a pas été endommagé
pendant le transport.
S’il est abîmé, ne pas le raccorder et contacter le revendeur.
2. Installer le lave-vaisselle de manière à ce que les côtés et la
paroi arrière touchent aux meubles adjacents ou au mur. L’appareil
peut être encastré sous un plan de travail continu
* (
voir feuille de
Montage
).
3. Installer le lave-vaisselle sur un sol plat et rigide. Compenser
les irrégularités en vissant ou en dévissant les pieds avant jusqu’à
ce que l’horizontalité de l’appareil soit parfaite. Une bonne
horizontalité garantit la stabilité de l’appareil et supprime tout
risque de vibrations, bruits et déplacements.
4
*. Pour régler la hauteur du pied arrière, agir sur la douille
rouge à six pans située dans la partie avant du lave-vaisselle, en
bas et au milieu, à l’aide d’une clé mâle à six pans, ouverture 8
mm. Tourner dans le sens des aiguilles d’une montre pour
augmenter la hauteur et dans le sens inverse pour la diminuer.
(consulter la notice d’instructions encastré jointe à la
documentation)
Raccordements eau et électricité
L’adaptation des installations électriques et les travaux de
plomberie de l’installation doivent être effectués par du personnel
qualifié.
Le lave-vaisselle ne doit pas écraser les tuyaux ou le câble
d’alimentation électrique.
Utiliser des tuyaux neufs pour effectuer le raccordement de
l’appareil au réseau de distribution de l’eau.
Ne pas réutiliser les anciens tuyaux.
Les tuyaux d’amenée et d’évacuation de l’eau et le câble
d’alimentation électrique peuvent être orientés vers la droite ou
vers la gauche pour simplifier l’installation.
Raccord du tuyau d’amenée de l’eau
• A une prise d’eau froide: bien visser le tuyau d’amenée à un
robinet à embout fileté 3/4 gaz; avant de visser, faire couler
l’eau jusqu’à ce quelle devienne limpide et dépourvue
d’impuretés qui pourraient engorger l’appareil.
• A une prise d’eau chaude: en cas d’installation de chauffage
centralisé (radiateurs), le lave-vaisselle peut être alimenté avec
de l’eau chaude de réseau ne dépassant pas 60°C.
Visser le tuyau au robinet en procédant comme pour la prise
d’eau froide.
Si la longueur du tuyau d’amenée ne suffit pas, s’adresser à
un magasin spécialisé ou à un technicien agréé (
voir Assistance
).
La pression de l’eau doit être comprise entre les valeurs
reportées dans le tableau des Caractéristiques techniques (
voir ci-
contre
).
Faire attention à ce que le tuyau ne soit ni plié ni écrasé.
Raccordement du tuyau d'évacuation de l'eau
raccorder le tuyau d'évacuation, sans le plier, à une
conduite d'évacuation ayant au moins 4 cm de diamètre.
Le tuyau d'évacuation doit être placé entre 40 et 80 cm
au-dessus du sol ou du plan d'appui du lave-vaisselle (A).
Avant de raccorder le tuyau d'évacuation de l'eau au
siphon de l'évier, retirer le bouchon en plastique (B).
Sécurité anti-fuite
Pour éviter tout risque d’inondation, le lave-vaisselle :
- est équipé d’un dispositif qui coupe l’arrivée de l’eau en cas
d’anomalie ou de fuite à l’intérieur de l’appareil.
Quelques modèles sont équipés d’un dispositif de sécurité
supplémentaire
New Acqua Stop
* qui garantit contre tout risque
d’inondation même en cas de rupture du tuyau d’amenée de
l’eau.
ATTENTION: TENSION DANGEREUSE!
Il ne faut en aucun cas couper le tuyau d’amenée de l’eau car il
contient des parties sous tension.
* Présent uniquement sur certains modèles.
FR
15
Raccordement électrique
Avant de brancher la fiche dans la prise de courant, s’assurer
que:
• la prise dispose de mise à la terre et est conforme aux normes;
• la prise est bien apte à supporter la puissance maximale de
l’appareil reportée sur la plaque signalétique fixée à la contre-
porte (
voir paragraphe Description du lave-vaisselle
);
• la tension d’alimentation est bien comprise entre les valeurs
figurant sur la plaque signalétique de la contre-porte;
• la prise est bien compatible avec la fiche de l’appareil.
Autrement, faire remplacer la fiche par un technicien agréé
(
voir Assistance
); n’utiliser ni rallonges ni prises multiples.
Après installation de l’appareil, le câble d’alimentation
électrique et la prise de courant doivent être facilement
accessibles.
Le câble ne doit être ni plié ni trop écrasé.
Afin d’éviter tout danger, faire changer le cordon d’alimenta-
tion abîmé, par le fabricant ou par son service après-vente. (Voir
Assistance)
Nous déclinons toute responsabilité en cas de non-respect
des normes énumérées ci-dessus.
Ruban anti-condensation*
Après avoir encastré le lave-vaisselle, ouvrir la porte et coller le
ruban adhésif transparent sous le plan en bois pour le protéger
contre la formation de condensation.
Conseils pour le premier lavage
Une fois l’installation terminée et tout de suite avant le premier
lavage, remplir complètement d’eau le réservoir à sel et ajouter
environ 1 kg de sel (
voir Produit de rinçage et sel régénérant
) : il
est tout à fait normal que de l’eau déborde. Sélectionner le degré
de dureté de l’eau (
voir Produit de rinçage et sel régénérant
). -
Après remplissage du réservoir à sel, le voyant SEL
* s'éteint.
Le manque de remplissage du réservoir à sel, peut
endommager l'adoucisseur d'eau et l'élément chauffant.
Caractéristiques techniques
Dimensions
largeur 60 cm
hauteur 85 cm
profondeur 60 cm
Capacité 14 couverts standard
Pression eau
d’alimentation
0,05 ÷ 1 MPa (0,5 ÷ 10 bar)
7,25 – 145 psi
Tension
d’alimentation
Voir étiquette des caractéristiques
Puissance totale
absorbée
Voir étiquette des caractéristiques
Fusible Voir étiquette des caractéristiques
Cet appareil est conforme aux
Directives Communautaires
suivantes:
- 2006/95/EC (Basse Tension)
- 2004/108/EC (Compatibilité
Electromagnétique)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Etiquetage)
-2002/96/EC (DEEE)
ECODESIGN REGULATION
Le cycle de lavage ECO c’est le programme standard auquel se référent les données de l’étiquette-énergie. Ce cycle est prévu pour le
lavage de la vaisselle normalement sale et est le programme le plus efficace en termes de consommation d’énergie et d’eau pour ce type
de vaisselle. Pour consommer moins, utiliser le lave-vaisselle à pleine charge.
Consommations en stand-by: Consommation en left-on mode: 3 W - Consommation en off-mode: 1,3 W
Tableau des consommations pour les cycles principaux
* Les données du programme sont des valeurs de mesure de laboratoire obtenues selon la norme européenne EN 50242.
** Les données sont obtenues en effectuant des mesures dans les conditions d’utilisation et de charge de la vaisselle de l’usager.
Conditions standard* Conditions usager**
Consommation
d'énergie (KWh/cycle)
Consommation
d'eau (litre/cycle)
Durée
(min/cycle)
Consommation
d'énergie (KWh/cycle)
Consommation
d'eau (litre/cycle)
Durée
(min/cycle)
INTENSIF
1,65 16 150 1,45 15 135
NORMAL
1,35 16 120 1,20 15 110
FR
16
Vue d’ensemble
Description de
l’appareil
1. Panier supérieur
2. Bras de lavage supérieur
3. Clayettes rabattables
4. Réglage hauteur du panier
5. Panier inférieur
6. Bras de lavage inférieur
7. Panier à couverts
8. Filtre lavage
9. Réservoir à sel
10. Bacs produit de lavage et réservoir à
produit de rinçage
11. Plaque signalétique
12. Tableau de bord
***
Tableau de bord
Touche
Sélection de
programme
Touche et Voyant
Pastilles multifonction*
Touche et voyant
Départ différé*
Touche et voyant
Demi-charge*
Voyant ON-OFF
Voyant
Manque de sel*
Voyant Manque de
produit de rinçage*
Touche et voyant option
séchage Super*
Voyants programme
Touche et voyant
Marche/Arret
Voyant Fin
Voyant Séchage
Voyant Lavage
Indicateur lumineux
du temps restant
Touche
ON-OFF/RESET
*** Uniquement pour modèles tout intégrables.
* Présent uniquement sur certains modèles.
Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.
FR
17
Charger les paniers
* Présent uniquement sur certains modèles. Leur nombre et
leur position varient.
Avant de charger les paniers, débarrasser la vaisselle des
déchets plus importants et vider les verres et les coupes.
Après avoir chargé le lave-vaisselle, s’assurer que les bras
de lavage tournent librement.
Panier inférieur et panier à couverts
Le panier du bas peut contenir des casseroles, des couvercles,
des assiettes, des saladiers, des couverts etc.Les assiettes et
couvercles de grandes dimensions doivent être de préférence
rangés sur les côtés du panier.
Certains modèles de lave-vaisselle sont pourvus de tiges
rabattables
*, qui peuvent être utilisés en position verticale pour
accueillir les assiettes ou en position horizontale pour accueillir
casseroles, saladiers et poêles.
Le panier à couverts peut varier selon le modèle de lave-vaisselle
et être séparable ou non séparable. Le panier à couverts non
séparable doit être placé obligatoirement dans la partie avant
du panier inférieur.
Ils sont tous deux
équipés de grilles
supérieures
permettant de mieux
ranger les couverts.
Ranger les couteaux et les ustensiles de cuisine pointus
et coupants dans le panier à couverts, pointes tournées vers
le bas, ou, à plat, sur les clayettes rabattables du panier
supérieur.
Panier supérieur
Réservé au chargement de la vaisselle fragile et légère : verres,
tasses, petites assiettes, saladiers bas.
Clayettes rabattables à inclinaison variable
Les clayettes peuvent être
placées à deux hauteurs
différentes afin d’optimiser la
disposition de la vaisselle
dans le panier. Les verres à
pied peuvent être placés en
position stable contre les
clayettes, en insérant la tige
de leurs pieds dans les
fentes
prévues à cet effet.
Régler la hauteur du panier supérieur
Pour faciliter le rangement de la vaisselle, il est possible de régler
le panier supérieur en position haute ou basse.
Régler de préférence la hauteur du panier supérieur
quand ce dernier est VIDE.
Ne JAMAIS soulever ou abaisser le panier d’un seul côté.
Ouvrir les butées des glissières du panier
à droite et à gauche et sortir le panier.
Positionner le panier en position haute ou
basse, le faire glisser le long des glissières
jusqu’à ce que les roues avant entrent elles
aussi et refermer les butées (
voir figure
).
Si le panier est équipé de poignées Dual
Space (
voir figure
), sortir le panier du haut
en fin de corse, saisir les poignées sur les
côtés du panier et déplacer vers le haut ou
vers le bas; laisser redescendre le panier
en l’accompagnant.
Vaisselle n’allant pas au lave-vaisselle
• Objets en bois, avec des manches en bois ou en corne ou
ayant des parties collées.
• Objets en aluminium, cuivre, laiton ou étain.
• Vaisselle en plastique non thermorésistant.
• Porcelaines anciennes ou peintes à la main.
• Argenterie ancienne. Les pièces d’argenterie non ancienne peuvent
par contre être lavées avec un programme délicat après s’être
assuré qu’elles n’entrent pas en contact avec d’autres métaux.
Nous vous conseillons dutiliser de la vaisselle adapte
pour passer au lave-vaisselle.
FR
18
Mise en marche et
utilisation
Charger le produit de lavage
Un bon résultat de lavage dépend aussi d’un bon dosage du
produit de lavage. Un excès de produit de lavage ne lave pas
mieux et pollue l’environnement.
N’utiliser que du produit de lavage spécial lave-
vaisselle.
NE PAS UTILISER de produits pour laver la
vaisselle à la main.
Une utilisation excessive de produit de lavage
peut laisser des résidus de mousse en fin de cycle.
L'utilisation de pastilles n'est conseillée que
pour les modèles qui prévoient l'option PASTILLES
MULTIFONCTION.
Pour obtenir des performances de lavage et de
séchage optimales, utiliser des produits de lavage
en poudre, du liquide de rinçage et du sel.
bac A: Produit de lavage
bac B: Produit de prélavage
1. Appuyer sur la touche D pour ouvrir
le couvercle C.
2. Pour doser le produit de lavage se
reporter au
Tableau des programmes
:
• en poudre : bacs A et B.
• pastilles : si le programme en prévoit
1, placer cette dernière dans le bac A
et fermer le couvercle; s’il en prévoit 2,
mettre la deuxième dans le fond de la
cuve.
3. Eliminer les résidus de produit de lavage sur les bords du bac
et fermer le couvercle jusqu’au déclic.
* Présent uniquement sur certains modèles.
Mettre en marche le lave-vaisselle
1. Ouvrir l'arrivée d'eau.
2. Appuyer sur la touche ON-OFF : un bip court retentit, tous les
voyants et l'afficheur s'allument pendant quelques secondes.
3. Ouvrir la porte et doser le produit de lavage (
voir plus bas
).
4. Charger les paniers (voir Charger les paniers) et fermer la
porte.
5. Pour sélectionner le programme selon le type de vaisselle et
son degré de salissure (
voir tableau des programmes
), appuyer
sur la touche P.
6. Sélectionner les options de lavage
* (
voir ci-contre
).
7. Appuyer sur la touche Marche/Pause pour faire démarrer le
lavage: un bip prolongé signale le démarrage du programme, le
voyant du lavage s'allume et le temps de lavage restant s'affiche.
8. A la fin, deux bips courts et un bip prolongé annoncent la fin du
programme, le voyant du programme qui vient de s'achever se
met à clignoter et le voyant FIN s'allume (
lumière fixe
). Eteindre
l'appareil par pression sur la touche ON-OFF, fermer le robinet
de l'eau et débrancher la fiche de la prise de courant.
9. Attendre quelques minutes avant de sortir la vaisselle pour
éviter de se brûler. Décharger les paniers en commençant par
celui du bas.
- Pour réduire sa consommation d'énergie, la
machine s'éteint automatiquement dans certaines
conditions de non-utilisation.
En cas de vaisselle peu sale ou précédemment rincée à
l’eau, réduire considérablement la quantité de produit de
lavage.
Modifier un programme en cours
En cas d’erreur de sélection d’un programme, il est possible de
le modifier, à condition qu’il vienne tout juste de démarrer : pour
changer un cycle de lavage en cours, éteindre puis rallumer
l’appareil par une pression prolongée sur la touche ON/OFF,
sélectionner ensuite le nouveau programme et les options
désirées.
Introduire de la vaisselle en cours de lavage
Appuyer sur la touche Marche/Arret, (la touche se met à clignoter).
Ouvrir la porte en faisant attention à la vapeur chaude qui
s’échappe et introduire la vaisselle. Appuyer sur la touche
Marche/Arret (lumière fixe): le cycle repart après un bip prolongé.
Appuyer sur la touche Marche/Arret pour mettre l’appareil
en pause, le programme et le départ différé éventuellement
sélectionné sont stoppés.
Pendant cette phase, aucun changement de programme n’est
possible.
Interruptions accidentelles
En cas d’ouverture de la porte en cours de lavage ou de
coupure de courant, le programme s’arrête. Il redémarre du
point où il a été interrompu dès que le courant revient ou que la
porte est refermée.
FR
19
Options de lavage*
La sélection, la modification ou l’annulation des
OPTIONS n’est possible qu’après avoir choisi le
programme de lavage et avant d’appuyer sur la
touche Marche/Arret.
Seules les options compatibles avec le programme choisi peuvent
être sélectionnées. Si une option n’est pas compatible avec le
programme sélectionné,
(voir tableau programmes)
la led
correspondante clignote 3 fois de suite et 2 bips courts
retentissent.
En cas de sélection d’une option incompatible avec une option
précédemment sélectionnée, celle-ci clignote 3 fois de suite, 3
bips retentissent puis elle s’éteint, tandis que la dernière sélection
effectuée reste allumée.
Pour désactiver une option sélectionnée par erreur, appuyer à
nouveau sur la touche correspondante.
Demi-charge dans le panier supérieur
Le programme demi-charge permet de laver une petite vaisselle
et de faire des économies d’eau, d’électricité et de produit de
lavage. Sélectionner le programme, appuyer sur la touche DEMI-
CHARGE: le voyant s’allume et le lavage n’est lancé que dans le
panier supérieur.
Penser à ne ranger la vaisselle que dans le panier
supérieur et à réduire de moitié la quantité de
produit de lavage.
Mieux vaut utiliser un produit de lavage en
poudre.
Cette option n’est pas utilisable avec les
programmes: Speed et Bébé.
Pastilles Multifonction
Cette option permet d’optimiser le résultat de lavage et de
séchage.
En cas d’utilisation de pastilles multifonction, appuyer sur la
touche PASTILLES MULTIFONCTION, le voyant correspondant
s’allume.
L’option “Pastilles Multifonction” prolonge la
durée du programme.
L’option pastilles multifonction reste mémorisée
lors des allumages suivants de l’appareil à moins qu’elle
n’ait été désactivée.
L’utilisation de pastilles n’est conseillée qu’en
présence de l’option PASTILLES MULTIFONCTION.
Cette option est déconseillée pour les programmes
qui ne prévoient pas l’utilisation de pastilles multifonction
(
voir tableau des options
).
* Présent uniquement sur certains modèles.
Séchage super*
Pour améliorer le séchage de la vaisselle, appuyer sur la touche
SÉCHAGE SUPER qui s’allume. Pour désactiver l’option appuyer
une nouvelle fois.
L’option SÉCHAGE SUPER prolonge la durée du
programme.
Départ différé
Possibilité de différer le départ du programme de 1 à 24 heures:
1. après avoir sélectionné le programme de lavage et toute autre
option possible, appuyer sur la touche DÉPART DIFFÉRÉ: le
voyant correspondant s’allume. Sélectionner à l’aide de la même
touche à quel moment on veut faire démarrer le cycle de lavage
(de 1 à 24 heures).
2. Confirmer son choix à l’aide de la touche Marche/Arret pour
faire partir le compte à rebours, le délai d’attente sélectionné se
met à clignoter et la touche Marche/Arret arrête de flasher (lumière
en fixe).
3. A l’expiration du délai d’attente, un bip prolongé retentit, le
voyant du DÉPART DIFFÉRÉ s’éteint et le programme démarre.
Pour désactiver un DÉPART DIFFÉRÉ, appuyer sur la touche
DÉPART DIFFÉRÉ jusqu’à affichage de OFF.
Aucune sélection de Départ différé n’est plus possible
en cours de cycle.
A B C D
Tableau Options
Départ
différé
Demi-
charge
Pastilles
Multifonction
Séchage
Super
Eco
Oui Oui Oui Oui
Normal
Oui Oui Oui Oui
Quotidien 60’
Oui Oui Oui Non
Trempage
Oui Oui Non Non
Intensif
Oui Oui Oui Oui
Speed 25’
Oui Non Oui Non
Cristal
Oui Oui Oui Oui
Bébé
Oui Non
Non
Non
FR
20
Programmes
En cas de vaisselle peu sale ou précédemment rincée à l’eau, réduire considérablement la quantité
de produit de lavage.
Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.
Remarques:
Pour obtenir des performances optimales avec les programmes "Quotidien et Speed 25’" il est conseillé de respecter le nombre de
couverts indiqué.
* Le programme Eco est conforme à la norme EN-50242. Il a une durée de lavage plus longue que les autres programmes
mais c’est aussi celui qui consomme le moins d’énergie et qui respecte le plus l’environnement.
Note pour les laboratoires d'essai
::
::
: pour toutes informations détaillées sur les conditions d'essai comparatif EN, s'adresser à:
Pour simplifier le dosage du produit de lavage, prendre note que:
1 cuillère à soupe = 15 gr. de poudre = 15 ml de liquide environ - 1 cuillère à café = 5 gr. de poudre = 5 ml de liquide environ
Produit de lavage
(A) = bac A
(B) = bac B
Indications sur le choix des
programmes
Programme
Poudre Liquide Pastilles
Programmes
prévoyant le
séchage
Options
Durée du
programme
(tolérance
±10%
Hrs. Min
Lavage écologique à faible
consommation d’électricité pour
vaisselle et casseroles.
Eco
*
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Oui
A-B-C-D
2:55’
Vaisselle et casseroles
normalement sales. Programme
standard quotidien.
Normal
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
Oui
A-B-C-D
1:50’
Vaisselle du jour en quantité
réduite. (4 couverts + 1 casserole +
1 poêle).
Quotidien 60’
25 g (A)
25 ml (A)
1 (A)
Non
A-B-C
1:00’
Lavage préalable dans l’attente de
compléter le chargement au repas
suivant
Trempage
Non
Non
Non
Non
A - B
0:08’
Vaisselle et casseroles très sales
(déconseillé pour la vaisselle
fragile)
Intensif
35 g (A)
35 ml (A)
1 (A)
Oui
A-B-C-D
2:25’
Cycle économique et rapide pour
vaisselle peu sale, tout de suite
après l’usage. (2 assiettes +2
verres +4 couverts +1 casserole +
1 petite poêle)
Speed 25’
25 g (A)
25 ml (A)
1 (A)
Non
A-C
0:25’
Cycle économique et rapide pour
vaisselle fragile ne supportant pas
les hautes températures, tout de
suite après l’usage. (verres à pied
pied panier supérieur + assiettes
fragiles, panier inférieur). Cristal
35 g (A)
35 ml (A)
1 (A)
Oui
A-B-C -D
1:30’
Cycle de lavage pour l’hygiène des
biberons, bagues, tétines, lavés en
même temps qu’assiettes, tasses,
verres et couverts. Charger
uniquement le panier du haut. Bébé
20 g (A)
20 ml (A)
Non
Oui
A
1:20’
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
Hotpoint LFFA+ 8M14 EU Le manuel du propriétaire
- Catégorie
- Lave-vaisselle
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
- English: Hotpoint LFFA+ 8M14 EU Owner's manual
- español: Hotpoint LFFA+ 8M14 EU El manual del propietario
- Deutsch: Hotpoint LFFA+ 8M14 EU Bedienungsanleitung
- Nederlands: Hotpoint LFFA+ 8M14 EU de handleiding
- português: Hotpoint LFFA+ 8M14 EU Manual do proprietário