Hotpoint-Ariston LFFA 8 M 14 EU Le manuel du propriétaire

Marque: Hotpoint-Ariston

Modèle: LFFA 8 M 14 EU

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

Operating instructions

Contents

Installation, 2-3

Positioning and levelling

Connecting the water and electricity supplies

Advice regarding the first wash cycle

Technical data

Ecodesign Regulation

Description of the appliance, 4

Overall view

Control panel

Loading the racks, 5

Lower rack

Cutlery basket

Upper rack

Start-up and use, 6-7

Starting the dishwasher

Measuring out the detergent

Wash options

Wash cycles, 8

Table of wash cycles

Rinse aid and refined salt, 9

Measuring out the rinse aid

Measuring out the refined salt

Care and maintenance, 10

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the water inlet filter

Cleaning the filters

Leaving the machine unused for extended periods

Precautions, advice and Assistance,11

General safety

Disposal

Saving energy and respecting the environment

Assistance

Troubleshooting, 12

English,1

DISHWASHER

LFFA+ 8M14

Español, 49 Português, 61

Français, 13 Deutsch, 25

Nederland,37

Ελληνικά, 73

Installation

Keep this instruction manual in a safe place for future

reference. If the appliance is sold, given away or moved, please

ensure the manual is kept with the machine, so that the new

owner may benefit from the advice contained within it.

Please read this instruction manual carefully: it contains

important information regarding the safe installation, use and

maintenance of the appliance.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto its

back.

This appliance is intended to be used in household and

similar applications such as:

- staff kitchen areas in shops, offices and other working

environments;

- farm houses;

- by clients in hotels, motels and other residential type

environments;

- bed and breakfast type environments.

Positioning and levelling

1. Remove the appliance from all packaging and check that it

has not been damaged during transportation.

If it has been damaged, contact the retailer and do not proceed

any further with the installation process.

2. Check the dishwasher by placing it so that its sides or back

panel are in contact with the adjacent cabinets or even with the

wall. This appliance can also be recessed under a single

worktop

* (

see the Assembly instruction sheet

3. Position the dishwasher on a level and sturdy floor. If the floor

is uneven, the front feet of the appliance may be adjusted until it

reaches a horizontal position. If the appliance is levelled correctly,

it will be more stable and much less likely to move or cause

vibrations and noise while it is operating.

*. Adjust the height of the rear foot from the front of the appliance

on the central lower part of the dishwasher, turning a hexagonal

spanner (red color) with an opening of 8 mm in a clockwise

direction to increase the height or in an anticlockwise direction to

decrease the height.

Connecting the water and electricity

supplies

Connection to the water and electricity supplies should only

be performed by a qualified technician.

The dishwasher should not stand on top of the water hoses

or the electricity supply cable.

The appliance must be connected to the water supply

network using new hoses.

Do not use old hoses.

The water inlet and outlet hoses and the electricity supply cable

may be positioned towards the right or the left in order to achieve

the best possible installation.

Connecting the water inlet hose

• To a suitable cold water connection point: before attaching the

hose, run the water until it is perfectly clear so that any impurities

that may be present in the water do not clog the appliance;

after performing this operation, screw the inlet hose tightly

onto a tap with a ¾ gas threaded connection.

• To a suitable hot water connection point: your dishwasher

may be supplied with hot water from the mains supply (if you

have a central heating system with radiators) provided that it

does not exceed a temperature of 60°C.

Screw the hose to the tap as described for connection to a

cold water supply.

If the inlet hose is not long enough, contact a specialist store

or an authorised technician (

see Assistance

The water pressure must be within the values indicated in the

Technical data table (

see adjacent information

The hose should not be bent or compressed.

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a drain duct

with a minimum diameter of 4 cm.

The outlet hose must be at a height ranging from 40 to 80

cm from the floor / surface where the dishwasher rests (A).

Before connecting the water outlet hose to the sink drain,

remove the plastic plug (B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply

in the event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety

device

New Acqua Stop

*, which guarantees anti-flooding

protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstance should the water inlet hose be cut as it

contains live electrical parts.

* Only available in selected models.

Electrical connection

Before inserting the plug into the electrical socket, make sure

that:

• The socket is earthed and complies with current regulations.

• The socket can withstand the maximum load of the appliance,

which is indicated on the data plate located on the inside of the

door (

see chapter entitled Description of the appliance

• The power supply voltage falls within the values indicated on

the data plate on the inside of the door.

• The socket is compatible with the plug of the appliance. If this

is not the case, ask an authorised technician to replace the

plug (

see Assistance

); do not use extension cables or multiple

sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, it must be replaced

by the manufacturer or its Technical Assistance Service in order to

prevent all potential hazards. (See Assistance)

The Company shall not be held responsible for any incidents

that occur if these regulations are not observed.

Anti-condensation strip*

After installing the dishwasher, open the door and stick the

adhesive transparent strip under the wooden shelf in order to

protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before running

the first wash cycle, completely fill the salt dispenser with water

and add only then approximately 1 kg of salt (

see chapter entitled

Rinse aid and refined salt

). The water may overflow: this is normal

and is not a cause for concern. Select the water hardness value

(

see chapter entitled Rinse aid and refined salt

). - After the salt

has been poured into the machine, the LOW SALT indicator

light

* switches off.

If the salt container is not filled, the water softener and the

heating element may be damaged as a result.

Technical data

Dimensions

width 60 cm

height 85 cm

depth 60 cm

Capacity 14 standard place-settings

Water supply

pressure

0,05 ÷ 1MPa (0.5 ÷ 10 bar)

7,25 – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse See appliance data plate

This dishwasher conforms to the

following European Community

Directives:

-2006/95/EC (Low Voltage)

-2004/108/EC (Electromagnetic

Compatibility)

-2005/32/EC (Comm. Reg.

1275/2008) (Ecodesign)

-97/17/EC (Labelling)

-2002/96/EC Waste Electrical

and Electronic Equipment

(WEEE)

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal

soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even

further, only run the dishwasher when it is full.

Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W

Consumption data table for the main cycles

* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.

** Data is obtained by recording values when the appliance is operational and loaded with user crockery.

Standard conditions* User conditions**

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

Energy consumption

(kWh/cycle)

Water consumption

(l/cycle)

Duration

(min/cycle)

INTENSIVE

1,65 16 150 1,45 15 135

NORMAL

1,35 16 120 1,20 15 110

Overall view

Description of the appliance

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

12. Control Panel

***

***Only in completely built-in models.

* Only available in selected models.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Control panel

ON/OFF

indicator light

Select wash

cycle button

Low rinse aid

indicator light*

Extra Dry option

button and

indicator light*

Low salt

indicator light*

Time remaining

light-up display

Start/Pause button

and indicator light

ON/OFF/Reset

button

Delayed start button

and indicator light*

Half load button

and indicator light*

Multi-functional tablets

button and indicator light*

Wash cycle

indicator lights

End indicator

light

Drying

indicator light

Washing

indicator light

Loading the racks

* Only available in selected models. The number and position

may vary.

Before loading the racks, remove all food residue from

crockery and empty liquids from glasses and cups.

After loading the appliance, make sure that the sprayer arms

can rotate freely.

Lower rack and cutlery basket

The lower rack can hold pans, lids, plates, salad bowls, cutlery, etc.

Large plates and lids should ideally be placed at the sides of the rack.

Several dishwasher models are fitted with tip-up sections

*, which

can be used in a vertical position when arranging plates or in a

horizontal position when arranging saucepans, salad bowls and

frying pans.

The type of cutlery basket may vary (modular or non-modular)

according to the dishwasher model. The non-modular basket

must only

be positioned at the front of the lower rack.

Both are fitted with

grilles over the

top, for improved

cutlery arrange-

ment.

Knives and other utensils with sharp edges must be placed

in the cutlery basket with the points facing downwards, or

they must be positioned horizontally in the tip-up

compartments on the upper rack.

Upper rack

Load this rack with delicate and lightweight crockery: glasses,

cups, saucers and shallow salad bowls.

Adjustable position tip-up compartments

The tip-up compartments

can be positioned at

different heights, to optimise

the arrangement of

crockery throughout the

rack. Wine glasses can be

placed safely in the tip-up

compartments, by inserting

the stem of each glass into

the corresponding slots.

Adjusting the height of the upper rack

In order to make it easier to arrange the crockery, the upper rack

may be moved to a higher or lower level.

The height of the upper rack should ideally be adjusted

WHEN THE RACK IS EMPTY.

NEVER raise or lower the rack on one side only.

Open the left and right guide rail stops

and pull out the rack; position it higher or

lower as required, slide it along the guide

rails until the front wheels are in place and

close the stops (

see figure

If the rack is fitted with Dual Space

handles

* (

see figure

), pull out the upper

rack until it reaches its stop point, grip

the handles at the sides of the rack and

move it upwards or downwards, then

slowly let it fall back into place.

Items that should not be washed in the dishwasher

• Wooden items, objects with wooden or horn handles or glued-

on parts.

• Items made from aluminium, copper, brass, pewter or tin.

• Items made from plastic material which is not heat-resistant.

• Antique or hand-painted porcelain.

• Antique silver. Silver that is not antique may, however, be

washed in the dishwasher using a delicate wash cycle,

provided that it does not come into contact with other metals.

We recommend the use of crockery which is dishwasher

safe.

Start-up and use

Starting the dishwasher

1. Turn the water tap on.

2. Premere il tasto ON-OFF: si sente un breve bip, tutte le spie e

il display si illuminano per alcuni secondi.

2. Press the ON/OFF button: you will hear a short beep; all the

indicator lights and the display will light up for a few seconds.

3. Open the door and pour in a suitable amount of detergent (

see

below

4. Load the racks (

see Loading the racks

) and shut the door.

5. Select the wash cycle in accordance with the type of crockery

and its soil level (

see Table of wash cycles

) by pressing the P

button.

6. Select the wash options

* (

see adjacent information

7. Start the cycle by pressing the Start/Pause button: a long

beep signals the start of the wash cycle, the washing cycle

indicator light switches on and the time remaining until the end of

the cycle is displayed.

8. Two short beeps and one long one indicate the end of the

wash cycle; the wash cycle indicator light flashes and the END

indicator light switches on (

fixed light

). Switch off the appliance

by pressing the ON/OFF button, shut off the water valve and

unplug the appliance from the electricity socket.

9. Wait for a few minutes before removing the crockery, in order

to avoid burns. Unload the racks, beginning with the lower level.

- The machine will switch off automatically

during certain periods of inactivity, in order to

minimise electricity consumption.

Modifying a wash cycle in progress

If a mistake was made during the wash cycle selection process

it is possible to change the cycle, provided that it has only just

begun: once the wash cycle has started, switch off the machine

by pressing and holding the ON/OFF/Reset button. Switch it

back on using the same button and select the desired wash

cycle and options.

Adding extra crockery

Press the Start/Pause button (the corresponding indicator light

will flash). Open the door, taking care to avoid the escaping

steam, and place the crockery inside the appliance. Press the

Start/Pause button (fixed light): the cycle will restart after a

prolonged beep is emitted.

If the Start/Pause button is pressed so as to pause the

machine, the wash cycle or the Delayed Start function (if

selected) is interrupted.

At this stage it is not possible to change the wash cycle.

Accidental interruptions

If the door is opened during the wash cycle, or if there is a power

cut, the cycle stops. It starts again from the point at which it was

interrupted once the door has been shut or once the electricity

supply is restored.

Measuring out the detergent

A good wash result also depends on the correct

amount of detergent being used; exceeding the

stated amount does not result in a more effective

wash and increases environmental pollution.

Only use detergent which has been specifically

designed for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam

residue remaining in the machine after the cycle

has ended.

The use of tablets is only recommended for

models which offer the MULTI-FUNCTIONAL

TABLETS option.

To achieve the best results from each washing

and drying cycle, powder detergent, rinse aid liquid

and salt should be used.

Compartment A: Washing detergent

Compartment B: Pre-wash detergent

1. Open cover C by pressing button

2. Pour in the detergent after consulting

the

Table of wash cycles

• For powder detergent use

compartments A and B.

• For detergent in tablet form: when

the cycle requires 1 tablet, place it in

compartment A and close the cover;

when it requires 2, place the second tablet at the bottom of the

appliance.

3. Remove detergent residues from the edges of the compartment

and close the cover until it clicks.

* Only available in selected models.

Multi-functional tablets (Tabs)

This option optimises washing and drying results.

When using multi-functional tablets, press the MULTI-

FUNCTIONAL TABLETS button. The corresponding indicator

light will illuminate. The “Multi-functional tablets” option results

in the lengthening of the wash cycle.

The MULTI-FUNCTIONAL TABLETS option remains

set for subsequent wash cycles if it is not deselected.

The use of tablets is only recommended for models

which offer the MULTI-FUNCTIONAL TABLETS option.

This option is not recommended for use with wash

cycles which do not specify the use of multi-functional

tablets

(

see Table of options

* Only available in selected models.

Half load using the upper rack

If there are not many dishes to be washed, a half load cycle may

be used in order to save water, electricity and detergent. Select

the wash cycle and press the HALF LOAD button: the indicator

light will illuminate and the wash cycle will take place only in the

upper rack.

Remember to load the upper rack only, and to reduce

the amount of detergent accordingly.

It is better to use powder detergent in this case.

This option is not compatible with the following wash

cycles: Speed and Baby.

Delayed start

It is possible to delay the start time of the cycle for a period of

time between 1 and 24 hours.

1. After selecting the desired wash cycle and any other options,

press the DELAYED START button: the corresponding indicator

light will illuminate. Use the same button to select the time at which

you wish the wash cycle to begin (after a period of 1 to 24 hours).

2. Confirm your selection using the Start/Pause button; the

countdown will begin. The selected delay period indicator light

flashes and the Start/Pause button stops flashing (the light

becomes fixed instead).

3. When the set time has elapsed, a long beep sounds, the

DELAYED START indicator light switches off and the wash cycle

begins.

To deselect the DELAYED START option, press the DELAYED

START button repeatedly until the text OFF appears.

The Delayed Start function cannot be set once the wash

has been started.

Wash options*

The OPTIONS may only be set, modified or reset after the

wash cycle has been selected and before the Start/Pause

button has been pressed.

Only the options which are compatible with the type of wash cycle

set may be selected. If an option is not compatible with the se-

lected wash cycle (

see Table of wash cycles

), the corresponding

LED flashes rapidly 3 times and 2 short beeps will sound.

If an option is selected which is incompatible with another (previ-

ously selected) option, the indicator light corresponding to the

option selected first will flash 3 times, 3 beeps will sound and it will

be deselected, while the most recently selected option will remain

active.

To deselect an option which has been set by mistake, press the

corresponding button again.

Extra drying*

To improve the dryness level of the crockery, press the EXTRA

DRYING button; the indicator light will illuminate. If it is pressed

again the option will be deselected.

The EXTRA DRYING option increases the duration of

the wash cycle.

A B C D

Table of options

Delayed

Start

Half

Load

Tabs

Extra

Dry

Eco

Yes

Normal

Yes

Daily A 60

Yes

Soak

Yes

Intensive

Yes

Speed 25’

Yes

Crystal

Yes

Baby wash

Yes

Wash cycles

For available OPTIONS please refer to the Table of options on the Start-up and use page.

If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher,

reduce the amount of detergent used accordingly.

The number and type of wash cycles and options may vary depending on the dishwasher model.

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle selection

instructions

Wash cycle

Powder Liquid Tablets

Wash

cycles

which

include

drying

Options

Wash cycle

duration

(tolerance

±10%)

Hrs. Min.

Environmentally-friendly wash cycle

with low energy consumption levels,

suitable for pans and dishes.

Eco

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Yes

A–B-C-D

2:55’

Normally soiled pans and dishes.

Standard daily wash cycle.

Normal

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Yes

A–B–C-D

1:50’

Limited quantity of daily soiling.

(4 place settings + 1 saucepan +1

frying pan).

Daily A 60

25 g (A)

25 ml (A)

1 (A)

A–B– C

1:00’

Pre-wash for dishes while awaiting

completion of the load with the

dishes from the next meal.

Soak

A – B

0:08’

Heavily soiled dishes and pans (not

to be used for delicate items).

Intensive

35 g (A)

35 ml (A)

1 (A)

Yes

A–B–C-D

2:25’

Economic and fast wash to be used

for lightly soiled dishes. (Run cycle

immediately after use) (2 plates + 2

glasses + 4 pieces of cutlery + 1

saucepan + 1 small frying pan).

25 g (A)

25 ml (A)

1 (A)

A - C

0:25’

Economic and fast wash for

delicate items which are sensitive to

high temperatures. (Run cycle

immediately after use) (glasses

upper rack + delicate plates, lower

rack). Crystal

35 g (A)

35 ml (A)

1 (A)

Yes

A–B–C-D

1:30’

Disinfecting wash cycle suitable for

washing bottles, rings and teats

together with plates, cups, glasses

and cutlery. The crockery should

only be loaded on the upper rack.

Baby Wash

20 g (A)

20 ml (A)

Yes

1:20'

Notes:

Optimum performance levels when using the "Daily wash" and "Speed wash" cycles can be achieved by observing the maximum

amounts of crockery specified.

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 grams of powder = approximately 15 ml of liquid - 1 teaspoon = 5 grams of powder = approximately 5 ml of

liquid

* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less

energy and is less harmful to the environment.

Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the following

address: [email protected]

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table salt or industrial salt, or washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

rinse aid; however, we recommend that you add salt, especially

if you live in an area where the water is hard or very hard.

Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW SALT

* and

LOW RINSE AID

* indicator lights remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs

off surfaces more readily and therefore does not leave streaks or

marks.

The rinse aid dispenser should be filled:

• When the LOW RINSE AID

* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning the

lid (G) in an anticlockwise direction.

2. Pour in the rinse aid, making sure it

does not overflow from the dispenser.

If this happens, clean the spill

immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may adjust the quantity of rinse aid used. Use a screwdriver to

turn the dosage adjuster (F) to one of the 6 pre-set positions (the

default position is set to 4):

• If there are streaks on the crockery, set the adjustment device

to a lower number (1-3).

• If drops of water remain on the crockery or if there are limescale

marks present after the cycle has finished, set the adjuster to a

higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of appliance,

supplies water without limescale which is then used to wash the

crockery.

This dishwasher offers a setting which helps to reduce pollution

and optimises washing performance in accordance with the water

hardness level in your area. This information can be obtained

from the organisation which supplies your household with water.

The water hardness adjustment procedure may vary

depending on the dishwasher model purchased.

- Switch on the appliance by pressing the ON/OFF button.

- Press and hold the P button for a few seconds; after a short

beep sounds, the water hardness setting will appear on the

display and the Start/Pause button will begin to flash (the default

water softening system setting is level

3).

- Press the P button repeatedly until the desired hardness level

has been reached (1-2-3-4-5

see Water hardness table

). The

selected water hardness value will appear on the display.

E.g.: hardness setting 1 ("1" appears on the display);

hardness setting 2 ("2" appears on the display);

hardness setting 3 ("3" appears on the display); etc., etc. up to a

maximum of level 5.

To exit the function, wait a few seconds or press one of the

option buttons

*, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees - mmol/l = millimoles per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash cycle,

make sure that the dispenser is never empty. Refined salt removes

limescale from the water, thus avoiding the formation of deposits

on crockery.

The salt dispenser is located in the lower part of the dishwasher

(

see Description

) and should be filled:

• When the green float

* cannot be seen by simply looking at the

cap of the salt dispenser.

• When the LOW SALT* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew the

container cap (anticlockwise).

2. The first time you do this: fill the water tank

right up to its edge.

3. Position the funnel

* (

see figure)

and fill

the salt container right up to its edge (this

should hold approximately 1 kg); it is not unusual for a little water

to leak out.

4. Remove the funnel* and wipe any salt residue away from the

opening; rinse the cap under running water and then screw it on,

the head facing downwards so as to let the water flow out of the

four cracks which are arranged in a star shape on the lower part

of the cap. (the container cap with the green float*)

It is advisable to perform this procedure every time you add

salt to the container.

Make sure the cap is screwed on tightly, so that no detergent

can get into the container during the wash cycle (this could

damage the water softener beyond repair).

When necessary, measure out the salt before a wash cycle

so that any saline solution which has leaked out of the salt

dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt container

capacity duration

Level

°dH

°fH

mmol/l

months

1 0 - 6 0 - 10 0 - 1

7 months

2 6 - 11 11 - 20 1,1 - 2

5 months

3 12 - 17 21 - 30 2,1 - 3

3 months

4 17 - 34 31 - 60 3,1 - 6

2 months

34 - 50

61 - 90

6,1 - 9

2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt

. *

this setting may cause a slight increase in the

duration of

the cycles.

for 1 wash cycle per day.

Care and maintenance

Shutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle to avoid

leaks.

• Always unplug the appliance when cleaning it and when

performing maintenance work.

Cleaning the dishwasher

• The external surfaces of the machine and the control

panel may be cleaned using a non-abrasive cloth which

has been dampened with water. Do not use solvents or

abrasive products.

• Any marks on the inside of the appliance may be

removed using a cloth dampened with water and a little

vinegar.

Preventing unpleasant odours

• Always keep the door of the appliance ajar in order to

avoid moisture from forming and being trapped inside

the machine.

• Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This will

avoid food becoming trapped in the seals, which is the

main cause behind the formation of unpleasant odours.

Cleaning the sprayer arms

Food residue may become encrusted onto the sprayer arms

and block the holes used to spray the water. It is therefore

recommended that the arms are checked from time to time

and cleaned with a small non-metallic brush.

The two sprayer arms may both be removed.

To remove the upper sprayer

arm, rotate the locking ring in an

anti-clockwise direction.

The upper sprayer arm should be

replaced with the holes facing

upwards.

The lower sprayer arm can be

removed by pressing on the side

tabs and pulling it upwards.

Cleaning the water inlet filter*

If the water hoses are new or have not been used for an

extended period of time, let the water run to make sure it is

clear and free of impurities before performing the necessary

connections. If this precaution is not taken, the water inlet

could become blocked and damage the dishwasher.

Clean the water inlet filter at the tap outlet regularly.

- Turn off the water tap.

- Unscrew the end of the water inlet hose, remove the filter

and clean it carefully under running water.

- Replace the filter and screw the water hose back into

position.

Cleaning the filters

The filter assembly consists of three filters which remove

food residues from the washing water and then recirculate

the water. They should be cleaned if you wish to achieve

the best results in every wash.

Clean the filters regularly.

The dishwasher should not be used without filters, or if

the filter is loose.

• After several washes, check the filter assembly and if

necessary clean it thoroughly under running water, using

a non-metallic brush and following the instructions below:

1.1.

1. Turn the cylindrical filter C in an anti-clockwise direction

and pull it out (fig. 1).

2.2.

2. Remove the cup filter B by exerting a slight pressure on

the side flaps (fig. 2).

3.3.

3. Slide out the stainless steel plate filter A (fig. 3).

Inspect the trap and remove any food residue.

NEVER REMOVE the wash cycle pump (black

detail)

(fig. 4)

After cleaning the filters, replace the filter assembly and fix

it in position correctly; this is essential for maintaining the

efficient operation of the dishwasher.

Leaving the machine unused for

extended periods

• Disconnect the appliance from the electricity supply and

shut off the water tap.

• Leave the door of the appliance ajar.

• When you return, run a wash cycle when the dishwasher

is empty.

* Only available in selected models.

Precautions, advice

and Assistance

This appliance was designed and manufactured in

compliance with current international safety standards. The

following information has been provided for safety reasons and

should therefore be read carefully.

General safety

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure that they do not play

with the appliance.

• The appliance was designed for domestic use inside the home

and is not intended for commercial or industrial use.

• The appliance must be used by adults only, to wash domestic

crockery in accordance with the instructions in this manual.

• The appliance must not be installed outdoors, even in covered

areas. It is extremely dangerous to leave the machine exposed

to rain and storms.

• Do not touch the appliance when barefoot.

• When unplugging the appliance always pull the plug from the

mains socket, do not pull on the cable.

• The water supply tap must be shut off and the plug should be

removed from the electrical socket before cleaning the

appliance or carrying out any maintenance work.

• If the appliance breaks down, do not under any circumstances

touch the internal parts in an attempt to perform the repair

work yourself.

• Never touch the heating element.

• Do not lean or sit on the open door of the appliance: this may

cause the appliance to overturn.

• The door should not be left open as it may create a dangerous

obstacle.

• Keep detergent and rinse aid out of reach of children.

• The packaging material should not be used as a toy.

Disposal

• Disposal of packaging materials: observe local legislation so

that the packaging may be reused.

• The European Directive 2002/96/EC relating to Waste Electrical

and Electronic Equipment (WEEE) states that household

appliances should not be disposed of using the normal solid

urban waste cycle. Exhausted appliances should be collected

separately in order to optimise the cost of re-using and

recycling the materials inside the machine, while preventing

potential damage to the atmosphere and to public health. The

crossed-out dustbin is marked on all products to remind the

owner of their obligations regarding separated waste

collection.

For further information relating to the correct disposal of

household appliances, owners may contact the relevant public

authority or the local appliance dealer.

Saving energy and respecting the

environment

Saving water and energy

• Only begin a wash cycle when the dishwasher is full. While

waiting for the dishwasher to be filled, prevent unpleasant

odours using the Soak cycle (

see Wash cycles

• Select a wash cycle which is suited to the type of crockery

and to the soil level of the crockery using the

Table of wash

cycles

- For dishes with a normal soil level, use the Eco wash cycle,

which guarantees low energy and water consumption levels.

- If the load is smaller than usual activate the Half load option

(

see Start-up and use

• If your electricity supply contract gives details of electricity

saving time bands, run wash cycles during the periods when

a lower tariff is applied. The Delayed start* button (

see Start-

up and use

) helps you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

• We strongly recommend that you use detergents that do not

contain phosphates or chlorine, as these products are harmful

to the environment.

• Enzymes provide a particularly effective action at temperatures

around 50°C, and as a result detergents containing enzymes

can be used in conjunction with low-temperature wash cycles

in order to achieve the same results as a normal 65°C wash

cycle.

• To avoid wasting detergent, use the product in appropriate

quantities based on the manufacturer’s recommendations, the

hardness of the water and the soil level and quantity of crockery

to be washed. Even if they are biodegradable, detergents

contain substances which may alter the balance of nature.

Assistance

Before contacting Assistance:

• Check whether the problem can be resolved using the

Troubleshooting guide (

see Troubleshooting

• Restart the programme to check whether the problem has

ceased to exist.

• If the problem persists, contact the Authorised Technical

Assistance Service.

Never use the services of unauthorised technicians.

Please have the following information to hand:

• The type of malfunction.

• The appliance model (Mod.).

• The serial number (S/N).

This information can be found on the appliance data plate (

see

Description of the appliance

* Only available in selected models.

Troubleshooting

Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance.

Problem:

Possible causes / Solutions:

The dishwasher does not start or

cannot be controlled

• Switch off the appliance by pressing the ON/OFF button, switch it back on after

approximately one minute and reset the program.

• The appliance has not been plugged in properly.

• The dishwasher door has not been shut properly.

The door won’t close • The lock was released. Strongly push the door until a “clacking” noise is heard.

No water drains out from the

dishwasher.

• The dishwasher cycle has not yet finished.

• The water inlet hose is bent (see Installation).

• The drain duct is blocked.

• The filter is clogged up with food residues.

The dishwasher makes excessive

noise.

• The dishes are rattling against each other or against the sprayer arms.

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up and

use).

The dishes and glasses are

covered in a white film or

limescale deposits.

• The level of the refined salt is low or the dosage setting is not suited to the hardness

of the water (see Rinse aid and salt).

• The lid on the salt dispenser is not closed properly.

• The rinse aid has been used up or the dosage is too low.

The dishes and glasses are

streaked or have a bluish tinge.

• The rinse aid dosage is too high.

The crockery has not been dried

properly.

• A wash cycle without a drying program has been selected.

• The rinse aid has been used up or the dosage is too low (see Rinse aid and salt).

• The rinse aid dispenser setting is not suitable.

• The crockery is made from non-stick material or plastic.

The dishes are not clean. • The racks are overloaded (see Loading the racks).

• The crockery has not been arranged well.

• The sprayer arms cannot move freely.

• The wash cycle is too gentle (see Wash cycles).

• An excessive amount of foam has been produced: the detergent has not been

measured out correctly or it is not suitable for use in dishwashers (see Start-up and

use).

• The lid on the rinse aid compartment has not been shut correctly.

• The filter is dirty or blocked (see Care and maintenance).

• The refined salt level is low (see Rinse aid and salt).

The dishwasher does not take any

water in - Tap shut-off alarm

(The ON/OFF indicator light flashes and

the display shows A 6).

• There is no water in the mains supply.

• The water inlet hose is bent (see Installation).

• Turn on the tap and the appliance will start after a few minutes.

• The appliance lock has been activated because no action was taken when the

beeps sounded.

Switch off the appliance using the ON/OFF button, turn on the tap and switch the

appliance back on after 20 seconds by pressing the same button. Re-program the

appliance and restart the wash cycle.

Water inlet hose alarm / Water inlet

filter blocked

(the ON/OFF indicator light flashes and

the display shows A 7).

• Switch off the appliance by pressing the ON/OFF button. Shut off the water tap to

eliminate the risk of flooding and remove the plug from the electrical socket.

Make sure the water inlet filter has not become blocked by impurities (see “Care

and maintenance” chapter).

Mode d’emploi

Sommaire

Installation, 14-15

Mise en place et mise à niveau

Raccordements eau et électricité

Conseils pour le premier lavage

Caractéristiques techniques

Ecodesign Regulation

Description de l’appareil, 16

Vue d’ensemble

Tableau de bord

Charger les paniers, 17

Panier inférieur

Panier à couverts

Panier supérieur

Mise en marche et utilisation, 18-19

Mettre en marche le lave-vaisselle

Charger le produit de lavage

Options de lavage

Programmes, 20

Tableau des programmes

Produit de rinçage et sel régénérant, 21

Charger le produit de rinçage

Charger le sel régénérant

Entretien et soin, 22

Coupure de l’arrivée d’eau et de courant

Nettoyer le lave-vaisselle

Eviter les mauvaises odeurs

Nettoyer les bras de lavage

Nettoyage du filtre d’entrée d’eau

Nettoyer les filtres

En cas d’absence pendant de longues périodes

Précautions conseils et Service, 23

Sécurité générale

Mise au rebut

Economies et respect de l’environnement

Service

Anomalies et remèdes, 24

Français, 13

LFFA+ 8M14

LAVE-VAISSELLE

Installation

Conserver ce mode d’emploi pour pouvoir le consulter à tout

moment. En cas de vente, de cession ou de déménagement,

s’assurer qu’il accompagne bien l’appareil.

Lire attentivement les instructions: elles contiennent des

conseils importants sur l’installation, l’utilisation et la sécurité de

l’appareil.

En cas de déménagement, transporter l’appareil

verticalement; si besoin est, l’incliner sur le dos.

Cet appareil est conçu pour un usage domestique ou autres

applications similaires, telles que :

- lieux aménagés en espace cuisine pour le personnel de

magasins, bureaux et autres lieux de travail ;

- fermes ;

- utilisation par les clients d'hôtels, de motels ou autres locaux de

type résidentiel ;

- chambres d'hôtes.

Mise en place et mise à niveau

1. Déballer l’appareil et s’assurer qu’il n’a pas été endommagé

pendant le transport.

S’il est abîmé, ne pas le raccorder et contacter le revendeur.

2. Installer le lave-vaisselle de manière à ce que les côtés et la

paroi arrière touchent aux meubles adjacents ou au mur. L’appareil

peut être encastré sous un plan de travail continu

* (

voir feuille de

Montage

3. Installer le lave-vaisselle sur un sol plat et rigide. Compenser

les irrégularités en vissant ou en dévissant les pieds avant jusqu’à

ce que l’horizontalité de l’appareil soit parfaite. Une bonne

horizontalité garantit la stabilité de l’appareil et supprime tout

risque de vibrations, bruits et déplacements.

*. Pour régler la hauteur du pied arrière, agir sur la douille

rouge à six pans située dans la partie avant du lave-vaisselle, en

bas et au milieu, à l’aide d’une clé mâle à six pans, ouverture 8

mm. Tourner dans le sens des aiguilles d’une montre pour

augmenter la hauteur et dans le sens inverse pour la diminuer.

(consulter la notice d’instructions encastré jointe à la

documentation)

Raccordements eau et électricité

L’adaptation des installations électriques et les travaux de

plomberie de l’installation doivent être effectués par du personnel

qualifié.

Le lave-vaisselle ne doit pas écraser les tuyaux ou le câble

d’alimentation électrique.

Utiliser des tuyaux neufs pour effectuer le raccordement de

l’appareil au réseau de distribution de l’eau.

Ne pas réutiliser les anciens tuyaux.

Les tuyaux d’amenée et d’évacuation de l’eau et le câble

d’alimentation électrique peuvent être orientés vers la droite ou

vers la gauche pour simplifier l’installation.

Raccord du tuyau d’amenée de l’eau

• A une prise d’eau froide: bien visser le tuyau d’amenée à un

robinet à embout fileté 3/4 gaz; avant de visser, faire couler

l’eau jusqu’à ce quelle devienne limpide et dépourvue

d’impuretés qui pourraient engorger l’appareil.

• A une prise d’eau chaude: en cas d’installation de chauffage

centralisé (radiateurs), le lave-vaisselle peut être alimenté avec

de l’eau chaude de réseau ne dépassant pas 60°C.

Visser le tuyau au robinet en procédant comme pour la prise

d’eau froide.

Si la longueur du tuyau d’amenée ne suffit pas, s’adresser à

un magasin spécialisé ou à un technicien agréé (

voir Assistance

La pression de l’eau doit être comprise entre les valeurs

reportées dans le tableau des Caractéristiques techniques (

voir ci-

contre

Faire attention à ce que le tuyau ne soit ni plié ni écrasé.

Raccordement du tuyau d'évacuation de l'eau

raccorder le tuyau d'évacuation, sans le plier, à une

conduite d'évacuation ayant au moins 4 cm de diamètre.

Le tuyau d'évacuation doit être placé entre 40 et 80 cm

au-dessus du sol ou du plan d'appui du lave-vaisselle (A).

Avant de raccorder le tuyau d'évacuation de l'eau au

siphon de l'évier, retirer le bouchon en plastique (B).

Sécurité anti-fuite

Pour éviter tout risque d’inondation, le lave-vaisselle :

- est équipé d’un dispositif qui coupe l’arrivée de l’eau en cas

d’anomalie ou de fuite à l’intérieur de l’appareil.

Quelques modèles sont équipés d’un dispositif de sécurité

supplémentaire

New Acqua Stop

* qui garantit contre tout risque

d’inondation même en cas de rupture du tuyau d’amenée de

l’eau.

ATTENTION: TENSION DANGEREUSE!

Il ne faut en aucun cas couper le tuyau d’amenée de l’eau car il

contient des parties sous tension.

* Présent uniquement sur certains modèles.

Raccordement électrique

Avant de brancher la fiche dans la prise de courant, s’assurer

que:

• la prise dispose de mise à la terre et est conforme aux normes;

• la prise est bien apte à supporter la puissance maximale de

l’appareil reportée sur la plaque signalétique fixée à la contre-

porte (

voir paragraphe Description du lave-vaisselle

);

• la tension d’alimentation est bien comprise entre les valeurs

figurant sur la plaque signalétique de la contre-porte;

• la prise est bien compatible avec la fiche de l’appareil.

Autrement, faire remplacer la fiche par un technicien agréé

(

voir Assistance

); n’utiliser ni rallonges ni prises multiples.

Après installation de l’appareil, le câble d’alimentation

électrique et la prise de courant doivent être facilement

accessibles.

Le câble ne doit être ni plié ni trop écrasé.

Afin d’éviter tout danger, faire changer le cordon d’alimenta-

tion abîmé, par le fabricant ou par son service après-vente. (Voir

Assistance)

Nous déclinons toute responsabilité en cas de non-respect

des normes énumérées ci-dessus.

Ruban anti-condensation*

Après avoir encastré le lave-vaisselle, ouvrir la porte et coller le

ruban adhésif transparent sous le plan en bois pour le protéger

contre la formation de condensation.

Conseils pour le premier lavage

Une fois l’installation terminée et tout de suite avant le premier

lavage, remplir complètement d’eau le réservoir à sel et ajouter

environ 1 kg de sel (

voir Produit de rinçage et sel régénérant

) : il

est tout à fait normal que de l’eau déborde. Sélectionner le degré

de dureté de l’eau (

voir Produit de rinçage et sel régénérant

). -

Après remplissage du réservoir à sel, le voyant SEL

* s'éteint.

Le manque de remplissage du réservoir à sel, peut

endommager l'adoucisseur d'eau et l'élément chauffant.

Caractéristiques techniques

Dimensions

largeur 60 cm

hauteur 85 cm

profondeur 60 cm

Capacité 14 couverts standard

Pression eau

d’alimentation

0,05 ÷ 1 MPa (0,5 ÷ 10 bar)

7,25 – 145 psi

Tension

d’alimentation

Voir étiquette des caractéristiques

Puissance totale

absorbée

Voir étiquette des caractéristiques

Fusible Voir étiquette des caractéristiques

Cet appareil est conforme aux

Directives Communautaires

suivantes:

- 2006/95/EC (Basse Tension)

- 2004/108/EC (Compatibilité

Electromagnétique)

-2005/32/EC (Comm. Reg.

1275/2008) (Ecodesign)

-97/17/EC (Etiquetage)

-2002/96/EC (DEEE)

ECODESIGN REGULATION

Le cycle de lavage ECO c’est le programme standard auquel se référent les données de l’étiquette-énergie. Ce cycle est prévu pour le

lavage de la vaisselle normalement sale et est le programme le plus efficace en termes de consommation d’énergie et d’eau pour ce type

de vaisselle. Pour consommer moins, utiliser le lave-vaisselle à pleine charge.

Consommations en stand-by: Consommation en left-on mode: 3 W - Consommation en off-mode: 1,3 W

Tableau des consommations pour les cycles principaux

* Les données du programme sont des valeurs de mesure de laboratoire obtenues selon la norme européenne EN 50242.

** Les données sont obtenues en effectuant des mesures dans les conditions d’utilisation et de charge de la vaisselle de l’usager.

Conditions standard* Conditions usager**

Consommation

d'énergie (KWh/cycle)

Consommation

d'eau (litre/cycle)

Durée

(min/cycle)

Consommation

d'énergie (KWh/cycle)

Consommation

d'eau (litre/cycle)

Durée

(min/cycle)

INTENSIF

1,65 16 150 1,45 15 135

NORMAL

1,35 16 120 1,20 15 110

Vue d’ensemble

Description de

l’appareil

1. Panier supérieur

2. Bras de lavage supérieur

3. Clayettes rabattables

4. Réglage hauteur du panier

5. Panier inférieur

6. Bras de lavage inférieur

7. Panier à couverts

8. Filtre lavage

9. Réservoir à sel

10. Bacs produit de lavage et réservoir à

produit de rinçage

11. Plaque signalétique

12. Tableau de bord

***

Tableau de bord

Touche

Sélection de

programme

Touche et Voyant

Pastilles multifonction*

Touche et voyant

Départ différé*

Touche et voyant

Demi-charge*

Voyant ON-OFF

Voyant

Manque de sel*

Voyant Manque de

produit de rinçage*

Touche et voyant option

séchage Super*

Voyants programme

Touche et voyant

Marche/Arret

Voyant Fin

Voyant Séchage

Voyant Lavage

Indicateur lumineux

du temps restant

Touche

ON-OFF/RESET

*** Uniquement pour modèles tout intégrables.

* Présent uniquement sur certains modèles.

Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.

Charger les paniers

* Présent uniquement sur certains modèles. Leur nombre et

leur position varient.

Avant de charger les paniers, débarrasser la vaisselle des

déchets plus importants et vider les verres et les coupes.

Après avoir chargé le lave-vaisselle, s’assurer que les bras

de lavage tournent librement.

Panier inférieur et panier à couverts

Le panier du bas peut contenir des casseroles, des couvercles,

des assiettes, des saladiers, des couverts etc.Les assiettes et

couvercles de grandes dimensions doivent être de préférence

rangés sur les côtés du panier.

Certains modèles de lave-vaisselle sont pourvus de tiges

rabattables

*, qui peuvent être utilisés en position verticale pour

accueillir les assiettes ou en position horizontale pour accueillir

casseroles, saladiers et poêles.

Le panier à couverts peut varier selon le modèle de lave-vaisselle

et être séparable ou non séparable. Le panier à couverts non

séparable doit être placé obligatoirement dans la partie avant

du panier inférieur.

Ils sont tous deux

équipés de grilles

supérieures

permettant de mieux

ranger les couverts.

Ranger les couteaux et les ustensiles de cuisine pointus

et coupants dans le panier à couverts, pointes tournées vers

le bas, ou, à plat, sur les clayettes rabattables du panier

supérieur.

Panier supérieur

Réservé au chargement de la vaisselle fragile et légère : verres,

tasses, petites assiettes, saladiers bas.

Clayettes rabattables à inclinaison variable

Les clayettes peuvent être

placées à deux hauteurs

différentes afin d’optimiser la

disposition de la vaisselle

dans le panier. Les verres à

pied peuvent être placés en

position stable contre les

clayettes, en insérant la tige

de leurs pieds dans les

fentes

prévues à cet effet.

Régler la hauteur du panier supérieur

Pour faciliter le rangement de la vaisselle, il est possible de régler

le panier supérieur en position haute ou basse.

Régler de préférence la hauteur du panier supérieur

quand ce dernier est VIDE.

Ne JAMAIS soulever ou abaisser le panier d’un seul côté.

Ouvrir les butées des glissières du panier

à droite et à gauche et sortir le panier.

Positionner le panier en position haute ou

basse, le faire glisser le long des glissières

jusqu’à ce que les roues avant entrent elles

aussi et refermer les butées (

voir figure

Si le panier est équipé de poignées Dual

Space (

voir figure

), sortir le panier du haut

en fin de corse, saisir les poignées sur les

côtés du panier et déplacer vers le haut ou

vers le bas; laisser redescendre le panier

en l’accompagnant.

Vaisselle n’allant pas au lave-vaisselle

• Objets en bois, avec des manches en bois ou en corne ou

ayant des parties collées.

• Objets en aluminium, cuivre, laiton ou étain.

• Vaisselle en plastique non thermorésistant.

• Porcelaines anciennes ou peintes à la main.

• Argenterie ancienne. Les pièces d’argenterie non ancienne peuvent

par contre être lavées avec un programme délicat après s’être

assuré qu’elles n’entrent pas en contact avec d’autres métaux.

Nous vous conseillons dutiliser de la vaisselle adapte

pour passer au lave-vaisselle.

Mise en marche et

utilisation

Charger le produit de lavage

Un bon résultat de lavage dépend aussi d’un bon dosage du

produit de lavage. Un excès de produit de lavage ne lave pas

mieux et pollue l’environnement.

N’utiliser que du produit de lavage spécial lave-

vaisselle.

NE PAS UTILISER de produits pour laver la

vaisselle à la main.

Une utilisation excessive de produit de lavage

peut laisser des résidus de mousse en fin de cycle.

L'utilisation de pastilles n'est conseillée que

pour les modèles qui prévoient l'option PASTILLES

MULTIFONCTION.

Pour obtenir des performances de lavage et de

séchage optimales, utiliser des produits de lavage

en poudre, du liquide de rinçage et du sel.

bac A: Produit de lavage

bac B: Produit de prélavage

1. Appuyer sur la touche D pour ouvrir

le couvercle C.

2. Pour doser le produit de lavage se

reporter au

Tableau des programmes

• en poudre : bacs A et B.

• pastilles : si le programme en prévoit

1, placer cette dernière dans le bac A

et fermer le couvercle; s’il en prévoit 2,

mettre la deuxième dans le fond de la

cuve.

3. Eliminer les résidus de produit de lavage sur les bords du bac

et fermer le couvercle jusqu’au déclic.

* Présent uniquement sur certains modèles.

Mettre en marche le lave-vaisselle

1. Ouvrir l'arrivée d'eau.

2. Appuyer sur la touche ON-OFF : un bip court retentit, tous les

voyants et l'afficheur s'allument pendant quelques secondes.

3. Ouvrir la porte et doser le produit de lavage (

voir plus bas

4. Charger les paniers (voir Charger les paniers) et fermer la

porte.

5. Pour sélectionner le programme selon le type de vaisselle et

son degré de salissure (

voir tableau des programmes

), appuyer

sur la touche P.

6. Sélectionner les options de lavage

* (

voir ci-contre

7. Appuyer sur la touche Marche/Pause pour faire démarrer le

lavage: un bip prolongé signale le démarrage du programme, le

voyant du lavage s'allume et le temps de lavage restant s'affiche.

8. A la fin, deux bips courts et un bip prolongé annoncent la fin du

programme, le voyant du programme qui vient de s'achever se

met à clignoter et le voyant FIN s'allume (

lumière fixe

). Eteindre

l'appareil par pression sur la touche ON-OFF, fermer le robinet

de l'eau et débrancher la fiche de la prise de courant.

9. Attendre quelques minutes avant de sortir la vaisselle pour

éviter de se brûler. Décharger les paniers en commençant par

celui du bas.

- Pour réduire sa consommation d'énergie, la

machine s'éteint automatiquement dans certaines

conditions de non-utilisation.

En cas de vaisselle peu sale ou précédemment rincée à

l’eau, réduire considérablement la quantité de produit de

lavage.

Modifier un programme en cours

En cas d’erreur de sélection d’un programme, il est possible de

le modifier, à condition qu’il vienne tout juste de démarrer : pour

changer un cycle de lavage en cours, éteindre puis rallumer

l’appareil par une pression prolongée sur la touche ON/OFF,

sélectionner ensuite le nouveau programme et les options

désirées.

Introduire de la vaisselle en cours de lavage

Appuyer sur la touche Marche/Arret, (la touche se met à clignoter).

Ouvrir la porte en faisant attention à la vapeur chaude qui

s’échappe et introduire la vaisselle. Appuyer sur la touche

Marche/Arret (lumière fixe): le cycle repart après un bip prolongé.

Appuyer sur la touche Marche/Arret pour mettre l’appareil

en pause, le programme et le départ différé éventuellement

sélectionné sont stoppés.

Pendant cette phase, aucun changement de programme n’est

possible.

Interruptions accidentelles

En cas d’ouverture de la porte en cours de lavage ou de

coupure de courant, le programme s’arrête. Il redémarre du

point où il a été interrompu dès que le courant revient ou que la

porte est refermée.

Options de lavage*

La sélection, la modification ou l’annulation des

OPTIONS n’est possible qu’après avoir choisi le

programme de lavage et avant d’appuyer sur la

touche Marche/Arret.

Seules les options compatibles avec le programme choisi peuvent

être sélectionnées. Si une option n’est pas compatible avec le

programme sélectionné,

(voir tableau programmes)

la led

correspondante clignote 3 fois de suite et 2 bips courts

retentissent.

En cas de sélection d’une option incompatible avec une option

précédemment sélectionnée, celle-ci clignote 3 fois de suite, 3

bips retentissent puis elle s’éteint, tandis que la dernière sélection

effectuée reste allumée.

Pour désactiver une option sélectionnée par erreur, appuyer à

nouveau sur la touche correspondante.

Demi-charge dans le panier supérieur

Le programme demi-charge permet de laver une petite vaisselle

et de faire des économies d’eau, d’électricité et de produit de

lavage. Sélectionner le programme, appuyer sur la touche DEMI-

CHARGE: le voyant s’allume et le lavage n’est lancé que dans le

panier supérieur.

Penser à ne ranger la vaisselle que dans le panier

supérieur et à réduire de moitié la quantité de

produit de lavage.

Mieux vaut utiliser un produit de lavage en

poudre.

Cette option n’est pas utilisable avec les

programmes: Speed et Bébé.

Pastilles Multifonction

Cette option permet d’optimiser le résultat de lavage et de

séchage.

En cas d’utilisation de pastilles multifonction, appuyer sur la

touche PASTILLES MULTIFONCTION, le voyant correspondant

s’allume.

L’option “Pastilles Multifonction” prolonge la

durée du programme.

L’option pastilles multifonction reste mémorisée

lors des allumages suivants de l’appareil à moins qu’elle

n’ait été désactivée.

L’utilisation de pastilles n’est conseillée qu’en

présence de l’option PASTILLES MULTIFONCTION.

Cette option est déconseillée pour les programmes

qui ne prévoient pas l’utilisation de pastilles multifonction

(

voir tableau des options

* Présent uniquement sur certains modèles.

Séchage super*

Pour améliorer le séchage de la vaisselle, appuyer sur la touche

SÉCHAGE SUPER qui s’allume. Pour désactiver l’option appuyer

une nouvelle fois.

L’option SÉCHAGE SUPER prolonge la durée du

programme.

Départ différé

Possibilité de différer le départ du programme de 1 à 24 heures:

1. après avoir sélectionné le programme de lavage et toute autre

option possible, appuyer sur la touche DÉPART DIFFÉRÉ: le

voyant correspondant s’allume. Sélectionner à l’aide de la même

touche à quel moment on veut faire démarrer le cycle de lavage

(de 1 à 24 heures).

2. Confirmer son choix à l’aide de la touche Marche/Arret pour

faire partir le compte à rebours, le délai d’attente sélectionné se

met à clignoter et la touche Marche/Arret arrête de flasher (lumière

en fixe).

3. A l’expiration du délai d’attente, un bip prolongé retentit, le

voyant du DÉPART DIFFÉRÉ s’éteint et le programme démarre.

Pour désactiver un DÉPART DIFFÉRÉ, appuyer sur la touche

DÉPART DIFFÉRÉ jusqu’à affichage de OFF.

Aucune sélection de Départ différé n’est plus possible

en cours de cycle.

A B C D

Tableau Options

Départ

différé

Demi-

charge

Pastilles

Multifonction

Séchage

Super

Eco

Oui Oui Oui Oui

Normal

Oui Oui Oui Oui

Quotidien 60’

Oui Oui Oui Non

Trempage

Oui Oui Non Non

Intensif

Oui Oui Oui Oui

Speed 25’

Oui Non Oui Non

Cristal

Oui Oui Oui Oui

Bébé

Oui Non

Non

Programmes

En cas de vaisselle peu sale ou précédemment rincée à l’eau, réduire considérablement la quantité

de produit de lavage.

Le nombre et les types de programmes et des options, varient selon le modele de lave-vaisselle.

Remarques:

Pour obtenir des performances optimales avec les programmes "Quotidien et Speed 25’" il est conseillé de respecter le nombre de

couverts indiqué.

* Le programme Eco est conforme à la norme EN-50242. Il a une durée de lavage plus longue que les autres programmes

mais c’est aussi celui qui consomme le moins d’énergie et qui respecte le plus l’environnement.

Note pour les laboratoires d'essai

: pour toutes informations détaillées sur les conditions d'essai comparatif EN, s'adresser à:

[email protected]

Pour simplifier le dosage du produit de lavage, prendre note que:

1 cuillère à soupe = 15 gr. de poudre = 15 ml de liquide environ - 1 cuillère à café = 5 gr. de poudre = 5 ml de liquide environ

Produit de lavage

(A) = bac A

(B) = bac B

Indications sur le choix des

programmes

Programme

Poudre Liquide Pastilles

Programmes

prévoyant le

séchage

Options

Durée du

programme

(tolérance

±10%

Hrs. Min

Lavage écologique à faible

consommation d’électricité pour

vaisselle et casseroles.

Eco

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Oui

A-B-C-D

2:55’

Vaisselle et casseroles

normalement sales. Programme

standard quotidien.

Normal

29 g (A)

6 g (B)

29 ml (A)

6 ml (B)

1 (A)

Oui

A-B-C-D

1:50’

Vaisselle du jour en quantité

réduite. (4 couverts + 1 casserole +

1 poêle).

Quotidien 60’

25 g (A)

25 ml (A)

1 (A)

Non

A-B-C

1:00’

Lavage préalable dans l’attente de

compléter le chargement au repas

Trempage

Non

A - B

0:08’

Vaisselle et casseroles très sales

(déconseillé pour la vaisselle

fragile)

Intensif

35 g (A)

35 ml (A)

1 (A)

Oui

A-B-C-D

2:25’

Cycle économique et rapide pour

vaisselle peu sale, tout de suite

après l’usage. (2 assiettes +2

verres +4 couverts +1 casserole +

1 petite poêle)

Speed 25’

25 g (A)

25 ml (A)

1 (A)

Non

A-C

0:25’

Cycle économique et rapide pour

vaisselle fragile ne supportant pas

les hautes températures, tout de

suite après l’usage. (verres à pied

pied panier supérieur + assiettes

fragiles, panier inférieur). Cristal

35 g (A)

35 ml (A)

1 (A)

Oui

A-B-C -D

1:30’

Cycle de lavage pour l’hygiène des

biberons, bagues, tétines, lavés en

même temps qu’assiettes, tasses,

verres et couverts. Charger

uniquement le panier du haut. Bébé

20 g (A)

20 ml (A)

Non

Oui

1:20’

La page charge ...

Hotpoint-Ariston LFFA 8 M 14 EU Le manuel du propriétaire

Marque: Hotpoint-Ariston

Modèle: LFFA 8 M 14 EU

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hotpoint-Ariston LFFA 8 M 14 EU Owner's manual
español: Hotpoint-Ariston LFFA 8 M 14 EU El manual del propietario
Deutsch: Hotpoint-Ariston LFFA 8 M 14 EU Bedienungsanleitung
Nederlands: Hotpoint-Ariston LFFA 8 M 14 EU de handleiding
português: Hotpoint-Ariston LFFA 8 M 14 EU Manual do proprietário

Hotpoint-Ariston LFFA 8 M 14 EU Le manuel du propriétaire

Ce manuel convient également à

Hotpoint-Ariston LFFA 8 M 14 EU Le manuel du propriétaire

dans d''autres langues

Autres documents