Kenmore 51299 Le manuel du propriétaire

Marque: Kenmore

Modèle: 51299

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Use & Care / Installation Manual

Manual de Uso y Cuidado / Instalación

English / Español

Models/Modelos 233.5128*, 233.5129*

Kenmore

Range Hood

Campana de cocina

* = color number, número de color

P/N 99045662-009A

Sears Brands Management Corporation,

Hoﬀ man Estates, IL 60179 USA

www.kenmore.com

READ AND SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

SECTION ................................................................... PAGE

Warranty ...................................................................................... 2

Safety Instructions ...................................................................... 3

Operation ..................................................................................... 4

Cleaning ....................................................................................... 4

Parts Included With Hood ........................................................ 5

Parts Not Included With Hood ................................................ 5

Tools Needed .............................................................................. 5

Equivalent Duct Length Chart .................................................. 6

Install Ductwork ......................................................................... 7

Prepare The Hood ................................................................. 7-9

Prepare The Hood Location .............................................. 10-13

EZ1 One-Person Installation ....................................... 10-11

Install The Hood (EZ-1 Brackets) .................................... 12

Standard Installation (without EZ1 Brackets) ............... 13

Install The Hood (Standard Installation) ....................... 13

Connect The Wiring .................................................................. 14

Install The Light Bulbs ................................................................ 15

Install The Filters ....................................................................... 15

Service Parts .............................................................................. 16

KENMORE LIMITED WARRANTY

5. Damage to or failure of this appliance, including discoloration

or surface rust, if it is not correctly operated and maintained

according to all supplied instructions.

6. Damage to or failure of this appliance, including discoloration

or surface rust, resulting from accident, alteration, abuse,

misuse or use for other than its intended purpose.

7. Damage to or failure of this appliance, including discoloration

or surface rust, caused by the use of detergents, cleaners,

chemicals or utensils other than those recommended in

all instructions supplied with the product.

8. Damage to or failure of parts or systems resulting from

unauthorized modiﬁ cations made to this appliance.

9. Service to an appliance if the model and serial plate is

missing, altered, or cannot easily be determined to have the

appropriate certiﬁ cation logo.

Disclaimer of implied warranties; limitation of remedies

Customer’s sole and exclusive remedy under this limited warranty

shall be product repair or replacement as provided herein. Implied

warranties, including warranties of merchantability or ﬁ tness for a

particular purpose, are limited to one year for the range hood

and thirty days for painted or bright metal parts, or the shortest

period allowed by law. Seller shall not be liable for incidental

or consequential damages. Some states and provinces do not

allow the exclusion or limitation of incidental or consequential

damages, or limitation on the duration of implied warranties

of merchantability or ﬁ tness, so these exclusions or limitations

may not apply to you.

This warranty applies only while this appliance is used in the

United States.

This warranty gives you speciﬁ c legal rights, and you may also

have other rights which vary from state to state.

Sears Brands Management Corporation,

Hoﬀ man Estates, IL 60179

WITH PROOF OF SALE, the following warranty coverage applies

when this appliance is correctly installed, operated and

maintained according to all supplied instructions.

FOR ONE YEAR from the date of sale this appliance is warranted

against defects in material or workmanship. A defective appliance

will receive free repair or replacement at option of seller. This

ONE YEAR coverage does not apply to the ﬁ nish of any painted

or bright metal part.

FOR THIRTY DAYS from the date of sale, any painted or bright

metal part of this product will be replaced free of charge if its

ﬁ nish is defective in material or workmanship.

For warranty coverage details to obtain free repair or replacement,

visit the web page: www.kenmore.com/warranty

All warranty coverage is void if this product is ever used for

other than private household purposes.

This warranty covers ONLY defects in material and workmanship,

and will NOT pay for:

1. Expendable items that can wear out from normal use, including but

not limited to ﬁ lters, belts, bags or screw-in base light bulbs.

2. A service technician to clean or maintain this appliance, or to

instruct the user in correct appliance installation, operation

and maintenance.

3. Service calls to correct appliance installation not performed

by Sears authorized service agents, or to repair problems

with house fuses, circuit breakers, house wiring, and plumbing

or gas supply systems resulting from such installation.

4. Damage to or failure of this appliance resulting from

installation not performed by Sears authorized service agents,

including installation that was not in accord with electrical,

gas or plumbing codes.

KENMORE LIMITED WARRANTY

SAFETY INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address listed in the warranty.

2. Before servicing or cleaning unit, switch power oﬀ at

service panel and lock the service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

3. Installation work and electrical wiring must be done by a

qualiﬁ ed person(s) in accordance with all applicable codes

and standards, including ﬁ re-rated codes and standards.

4. Sufficient air is needed for proper combustion and

exhausting of gases through the ﬂ ue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. To reduce the risk of ﬁ re or electric shock, do not use this

range hood with an additional speed control device.

7. Ducted fans must always be vented to the outdoors.

8. To reduce the risk of ﬁ re, use only metal ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

cooking ﬂ aming foods.

3. Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or ﬁ lter.

4. Use proper pan size. Always use cookware appropriate

for the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-ﬁ tting lid, cookie sheet,

or metal tray, then turn oﬀ the burner. BE CAREFUL TO

PREVENT BURNS. If the ﬂ ames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels

- a violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The ﬁ re is small and contained in the area where it

started.

C. The ﬁ re department is being called.

D. You can ﬁ ght the ﬁ re with your back to an exit.

* Based on “Kitchen Fire safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, construction

dust, etc. oﬀ power unit.

3. For best capture of cooking impurities, your range hood

should be mounted so that the top of the hood is 18-24”

above the cooking surface.

4. Use only with range hood cord-connection kits that have

been investigated and found acceptable for use with this

model range hood.

5. Please read speciﬁ cation label on product for further

information and requirements.

NOTE

If hood is to be installed Non-Ducted:

Purchase non-ducted ﬁ lters and attach them to the

aluminum mesh ﬁ lters

“Non-ducted Filters” available by calling

1-844-553-6667

WARNING: To reduce the risk of electric shock,

disconnect from power supply before cleaning.

Micromesh ﬁ lters

Clean frequently using hot water and a mild detergent or

in your dishwasher. The micromesh ﬁ lters should be washed

approximately every month depending on the amount of

usage. Wash more often if your cooking style generates

greater grease - like frying foods or wok cooking.

Non-ducted recirculation ﬁ lters

(available separately - see page 5)

The non-ducted recirculation ﬁ lters should be changed

every 3 to 6 months. Replace more often if your cooking style

generates extra grease, such as frying and wok cooking.

Refer to installation instructions included with non-ducted

recirculation ﬁ lters.

Painted hood surfaces

Clean with warm water and mild detergent only. If

discoloration occurs, use a ﬁ nish polish such as automotive

polish. (DO NOT use rough abrasive cleaner or porcelain

cleaner.)

Stainless steel hood surfaces

Do:

• Regularly wash with clean cloth or rag soaked with

warm water and mild soap or liquid dish detergent.

• Always clean in the direction of original polish lines.

• Always rinse well with clear water (2 or 3 times) after

cleaning. Wipe dry completely.

• You may also use a specialized household stainless

steel cleaner.

Don’t:

• Use any steel or stainless steel wool or any other

scrapers to remove stubborn dirt.

• Use any harsh or abrasive cleansers.

• Allow dirt to accumulate.

• Let plaster dust or any other construction residues

reach the hood. During construction/renovation, cover

the range hood to make sure no dust sticks to the

stainless steel surface.

Avoid when choosing a detergent:

• Any cleaners that contain bleach will attack stainless steel.

• Any products containing: chloride, ﬂ uoride, iodide,

bromide will deteriorate surfaces rapidly.

• Any combustible products used for cleaning such as

acetone, alcohol, ether, benzol, etc., are highly explosive

and should never be used close to a range.

Fan assembly

The fan blade should be cleaned frequently. Use a clean

cloth soaked with warm detergent solution.

The motor is permanently lubricated and never needs

oiling. If the motor bearings make excessive or unusual

noise, replace the motor with the exact service motor. The

fan blade should also be replaced.

CLEANINGOPERATION

ON/OFF BLOWER

PUSH BUTTON

ON/OFF BLOWER PUSH BUTTON

When blower is OFF, push on this button to turn ON the

blower at the last selected speed. Push on this button again

to turn OFF the blower.

NOTE: If there is no speed selected (all blower speed

push buttons up), the blower will not turn ON. In

that case, press on the desired speed level push

button to activate the blower.

BLOWER SPEED LEVEL PUSH BUTTONS

When blower is ON, change the blower speed by pressing

on the push button corresponding to the desired speed:

one line for LOW, two lines for MEDIUM and three lines for

HIGH speed.

ON/OFF LIGHT PUSH BUTTON

When lights are OFF, push once on this button to turn ON

the lights at the last selected setting. Push on this button

again to turn OFF the lights.

LIGHT INTENSITY LEVELS PUSH BUTTON

Push on this button to change the light intensity (HIGH or

LOW).

BLOWER SPEED LEVEL

PUSH BUTTONS

ON/OFF LIGHT

PUSH BUTTON

LIGHT INTENSITY

LEVELS PUSH BUTTON

PARTS INCLUDED WITH HOOD

TOOLS NEEDED FOR HOOD INSTALLATION

Micromesh Grease Filters

(2 per hood)

Parts Bag

(4 no. 8-18 x 1/2" metal screws,

6 no. 8 x 5/8" round head wood screws,

6 no. 8 x 1/2" countersunk wood screws,

1 suction cup tool)

Screwdriver

(Flat & Phillips no. 2)

Pencil

Tape

Measure

Drill

(with 1/8" and

7/64" drill bits,

and 1½" hole saw)

Sabre Saw

Keyhole

Saw

-or-

Metal Foil

Duct Tape

Wire

Stripper

PARTS NOT INCLUDED WITH HOOD

OPTIONAL PARTS (purchase separately)

Non-Ducted Recirculation Filters

(Non-ducted hoods only)

(2 per hood)

Part Nos.:

S97020466 (30-in. width hoods)

S97020467 (36-in. width hoods)

7-inch Round Damper

(For use with 7-inch Round Duct)

Part No. 59183

3¼” x 10”

Damper / Duct

Connector

Apoyar este borde contra la pared de atrásPlace this edge against back wall

VERTICAL EXHAUST

RTICAL EX

= 3¼” x 10”

= 3¼” x 14”

RECTANGULAR DUCTING7” ROUND DUCTING

Use this template for marking; do not attempt to cut out the ducting hole through it.

NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.

= 3¼ po x 10 po

= 3¼ po x 14 po

CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO

= 3¼ pulg. x 10 pulg.

= 3¼ pulg. x 14 pulg.

CONDUCTO RECTANGULARCONDUCTO REDONDO

7 PULG.

Appuyer ce bord au mur arrière

Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper

le trou pour le conduit à travers le gabarit.

NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas

être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el

agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

TITLE TO BE TRANSLATED IN SPANIS H

Electrical access hole center

A = single blower hood

B = double blower hood

Centre du trou pour fil

d’alimentation électrique

A = hotte ventilateur simple

B = hotte ventilateur double

To be translated in Spanish

Electrical access hole center

A = single blower hood

B = double blower hood

4¼”

10½”

14½”

8”

7½”

Bend template along graduated

scale when installing to framed

cabinet.

Pour une installation sous une

armoire à fond en retrait, utiliser les

lignes pour mesurer l’épaisseur du

décalage causé par le mur de

l’armoire et plier le gabarit en

conséquence.

To be translated in Spanish.

EZ-1 One person Installation Kit

(including template for

ducting, printed both sides,

and installation brackets)

7” Round

Duct Connector

Long Nose

Pliers

HR0064

Sheet Metal

Shears

Shielded Halogen Bulbs

(120 V, 50 W max., MR16 or

PAR16 with GU10 base)

(2 per hood)

“Parts Not Included With Hood” available by calling

1-844-553-6667

EQUIVALENT DUCT LENGTH CHART

Straight Duct

3¼-in. x 10-in. x 2-ft. long

Equivalent length

2 ft.

7-in. Round Elbow

Equivalent length

8 ft.

3¼-in. x 10-in.

Right-angle Elbow

Equivalent length

8.5 ft.

3¼-in. x 10-in.

Right-angle Flat Elbow

Equivalent length

24 ft.

3¼-in. x 10-in.

Right-angle

Short Eave

Elbow

Equivalent length

15 ft.

3¼-in. x 10-in.

Right-angle

Long Eave

Elbow

Equivalent length

15 ft.

3¼-in. x 10-in.

Wall Cap

Equivalent

length

45 ft.

(7-ft. w/o

damper)

Roof Cap

(accepts 7-in. round

or 3¼-in. x 10-in. duct)

Equivalent length

30 ft. (7-ft. w/o damper)

Kenmore range hoods are designed to perform eﬃ ciently when attached to long runs of duct. As a point of reference, this

hood will function at approximately 80% of its rated air ﬂ ow when 25 equivalent feet of 7" round ductwork is attached.

Use this chart to calculate the equivalent duct length of your system.

Straight Duct

7-in. round x 2-ft. long

Equivalent length

2 ft.

3¼-in. x 10-in. to

7-in. Round

Transition

Equivalent length

5.5 ft.

B7-in. Round

Wall Cap

Equivalent length

34 ft.

(6-ft. w/o damper)

“Ducting Accessories” available by calling

1-844-553-6667

SOFFIT

18" MIN - 24" MAX

ABOVE

COOKING SURFACE

CABINET

3¼" X 10" DUCT

(FOR HORIZONTAL DISCHARGE)

WALL CAP

ROOF CAP

3¼" X 10" OR

7" ROUND DUCT

(FOR VERTICAL

DISCHARGE

)

HOUSE WIRING

(TOP OR BACK OF HOOD)

HOOD

1. Determine whether hood will discharge vertically (3¼” x 10”

or 7” Round) or horizontally (3¼” x 10” only).

2. Run ductwork between the hood location and a roof cap

or wall cap.

3. Choose a straight, short duct run to allow the hood to

perform most eﬃ ciently. Long duct runs, elbows and

transitions will reduce the performance of the hood. Use

as few of them as possible. When possible, use at least

2 foot straight runs before any turns. Larger ductwork may

be required for best performance with longer duct runs.

4. Install wall cap or roof cap (sold separately); ensure there

is no leak in hoiouse insulation. Connect metal ductwork

to cap and work back towards the hood location. Use 2”

metal foil duct tape to seal the joints between ductwork

sections.

INSTALL DUCTWORK (DUCTED INSTALLATION ONLY)

NOTE: Distances over 24” are at the installer and user

discretion.

1. If present, remove all protective polyﬁ lm from the hood

and/or parts. Using the ﬁ nger cup, remove the

Micromesh Filters from the hood by pushing down and

tilting ﬁ lters out.

PREPARE THE HOOD

DAMPER

ASSEMBLY

SCREWS

EZ1

BRACKETS

2. Remove the EZ1 brackets from inside the hood by

cutting oﬀ the tie wrap. Remove both screws holding

damper assembly to hood. Remove parts bag

(captured behind the damper assembly). Remove

damper assembly from inside the hood and keep the

screws for further use.

4. Remove 7” Round Duct Plate from top/back of hood (see

illustration beside).

RECIRCULATION

COVER PLATE

SCREWS

ELECTRICAL

POWER CABLE

KNOCKOUT

7” ROUND

DUCT PLATE

2 SCREWS

5. Remove Electrical Power Cable Knockout from top

(vertical exhaust) or back (horizontal exhaust) of

hood. Install an appropriate strain relief, 1/2” diameter

(not included).

NON-DUCTED INSTALLATIONS ONLY

6. Remove 3 screws retaining the recirculation cover plate

(shaded part in illustration beside) to the hood. Discard

this plate with its screws.

3. Remove the wiring cover (shaded part on illustration

beside) by sliding it out from the hood and set it aside.

DUCTED INSTALLATIONS ONLY

7. Remove 3¼” x 10” vertical, 3¼” x 10” horizontal, or 7-inch round knockout plate as appropriate for your ducting

method (see FIGURES 1 A and 1 B).

NOTE: To accommodate oﬀ -center ductwork, the 7” round duct plate can be installed up to 1/2” on either side of

the hood center.

7” ROUND

DUCT

PLATE

SCREWS

FIGURE 3

3¼” X 10”

DAMPER

ASSEMBLY

SCREWS

FIGURE 2 A

TOP/BACK

EDGE OF

HOOD

DAMPER

FLAP

PIVOT

FIGURE 2 B

3¼” X 10”

DAMPER

ASSEMBLY

BACK OF

HOOD

DAMPER

FLAP

PIVOT

SCREWS

7” ROUND

KNOCKOUT PLATE

(ALSO REMOVE VERTICAL

KNOCKOUT PLATE)

3¼” X 10”

VERTICAL

KNOCKOUT

PLATE

3¼” X 10”

HORIZONTAL

KNOCKOUT

PLATE

FIGURE 1 A FIGURE 1 B

8. Attach 3¼” x 10” Damper Assembly on top OR back of hood (if using 3¼” x 10” duct; shaded part in F

IGURE 2 A)

or 7” Round Duct Plate (if using 7-inch round duct, FIGURE 3) over the knockout opening. When installed, the 3¼” x 10”

damper assembly must open as shown in F

IGURE 2 B.

TIP: Insert a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting) or 7” round (for round

ducting) and seal the joint using aluminum foil duct tape to ease connection with the house ductwork.

PREPARE THE HOOD LOCATION

NOTE: Before starting installation, read all the steps

of these instructions.

Use the illustration beside to identify your kitchen cabinet

type.

EZ1 One-person installation system

This manual covers 2 kinds of installation: the standard

(without EZ1 brackets) and the EZ1 one-person installation

system (using included template and brackets). For the

standard installation, go to page 13.

FRAMED CABINET FRAMELESS CABINET

CABINET FRONT

Apoyar este borde contra la pared de atrásPlace this edge against back wall

VERTICAL EXHAUST

RTICAL EX

= 3¼” x 10”

= 3¼” x 14”

RECTANGULAR DUCTING7” ROUND DUCTING

Use this template for marking; do not attempt to cut out the ducting hole through it.

NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.

= 3¼ po x 10 po

= 3¼ po x 14 po

CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO

= 3¼ pulg. x 10 pulg.

= 3¼ pulg. x 14 pulg.

CONDUCTO RECTANGULARCONDUCTO REDONDO

7 PULG.

Appuyer ce bord au mur arrière

Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper

le trou pour le conduit à travers le gabarit.

NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas

être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el

agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

TITLE TO BE TRANSLATED IN SPANISH

Electrical access hole center

A = single blower hood

B = double blower hood

Centre du trou pour fil

d’alimentation électrique

A = hotte ventilateur simple

B = hotte ventilateur double

To be translated in Spanish

Electrical access hole center

A = single blower hood

B = double blower hood

4¼”

10½”

14½”

8”

7½”

Bend template along graduated

scale when installing to framed

cabinet.

Pour une installation sous une

armoire à fond en retrait, utiliser les

lignes pour mesurer l’épaisseur du

décalage causé par le mur de

l’armoire et plier le gabarit en

conséquence.

To be translated in Spanish.

CABINET FRONT

VERTICAL EXHAUST

RTICAL EX

= 3¼” x 10”

= 3¼” x 14”

RECTANGULAR DUCTING7” ROUND DUCTING

Use this template for marking; do not attempt to cut out the ducting hole through it.

NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.

= 3¼ po x 10 po

= 3¼ po x 14 po

CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO

= 3¼ pulg. x 10 pulg.

= 3¼ pulg. x 14 pulg.

CONDUCTO RECTANGULARCONDUCTO REDONDO

7 PULG.

Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper

le trou pour le conduit à travers le gabarit.

NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas

être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el

agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

TITLE TO BE TRANSLATED IN SPANISH

Electrical access hole center

A = single blower hood

B = double blower hood

Centre du trou pour fil

d’alimentation électrique

A = hotte ventilateur simple

B = hotte ventilateur double

To be translated in Spanish

Electrical access hole center

A = single blower hood

B = double blower hood

4¼”

10½”

14½”

8”

7½”

Bend template along graduated

scale when installing to framed

cabinet.

Pour une installation sous une

armoire à fond en retrait, utiliser les

lignes pour mesurer l’épaisseur du

décalage causé par le mur de

l’armoire et plier le gabarit en

conséquence.

To be translated in Spanish.

ELECTRICAL

ACCESS HOLE

LOCATION (A)

(

IN CABINET BOTTOM)

CENTER LINE

FOLD TEMPLATE ALONG GRADUATED

SCALE

WHEN INSTALLING TO FRAMED

CABINET

VERTICAL

EXHAUST DUCTING

EZ1 installation is designed for use with kitchen cabinets that have the same width designation as the range hood

width. If the cabinet is greater than 1/2” wider than the range hood width, please use the standard installation method.

1. Use the proper template for vertical OR horizontal

disharge (included) for placement of ductwork and electrical

cutout in cabinet or wall. For a non-ducted installation, DO

NOT cut a duct access hole, only cut the hole for electrical

wiring. If replacing a hood and plan to use the existing

duct and electrical, steps 2 to 5 may not be necessary. If

so, skip to step 6.

2. Measure and mark the hood center line on cabinet bottom.

3. Align the center line on template with the hood center

line marked on the bottom of the cabinet, placing the

edge (where indicated) of the template against back

wall. When using with framed cabinet for vertical exhaust

installation, fold over rear edge of template equal to the

depth of the cabinet frame at the wall (use graduations

on template, C locations on template). Tape the template

in place.

NOTE: When facing the installation, A and B (on

template) must be at right.

Electrical access hol

A = single blower ho

B = double blower

Centre du tr

d’alim

ELECTRICAL

ACCESS HOLE

LOCATION (A)

(

IN WALL)

CENTER LINE

Place this edge against

cabinet bottom.

Appuyer ce bord contre le bas

de l’armoire.

Apoyar este borde contra

la base del armario.

HORIZONTAL EXHAUST

= 3¼ pulg. x 10 pulg.

= 3¼ pulg. x 14 pulg.

CONDUCTO RECTANGULAR

= 3¼” x 10”

= 3¼” x 14”

RECTANGULAR DUCTING

= 3¼ po x 10 po

= 3¼ po x 14 po

CONDUIT RECTANGULAIRE

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

TITLE TO BE TRANSLATED IN SPANISH

Use this template for marking; do not attempt to cut out the ducting hole through it.

NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.

Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper

le trou pour le conduit à travers le gabarit.

NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas

être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el

agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

Electrical access hole center

A = single blower hood

B = double blower hood

Centre du trou pour fil

d’alimentation électrique

A = hotte ventilateur simple

B = hotte ventilateur double

To be translated in Spanish

Electrical access hole center

A = single blower hood

B = double blower hood

HORIZONTAL

EXHAUST DUCTING

4. Drill a 1/8” dia. pilot hole for house wiring, at A location

on template.

5. Use a sharp pencil or 1/8” drill bit to mark the locations

for the appropriate duct access holes (16 locations for 7”

round duct, or 4 corner locations for rectangular duct).

Remove the template.

6. Draw the border for the exhaust ducting by linking its

marks (16 for round duct and 4 for rectangular duct), then

cut the opening in the cabinet bottom (vertical exhaust)

or in the wall (horizontal exhaust). Drill the house wiring

hole by using a 1½” hole saw centered with the pilot hole

previously made in 4.

FRAMED CABINET

7/64”

Refer to the marking on the brackets to determine

the correct installation side and orientation.

Mate the corresponding bracket to the cabinet side

frame, while placing rear end of bracket against the

wall. Use a pencil to mark 3 holes (there are 6 holes

but only 3 are necessary).

Remove the bracket. Using a 7/64” drill bit, drill 3 holes

where marked.

7. Install the proper installation brackets according to the

type of cabinet (framed or frameless). See below.

Assemble the bracket to the side frame using a Phillips

screwdriver and 3 provided no. 8 x 5/8” wood screws.

Repeat for the other side frame.

FRAMELESS CABINET

Refer to the marking on the brackets to determine

the correct installation side and orientation.

[ \

7/64”

3 X

Align the corresponding bracket to the cabinet side,

while placing rear end of bracket against the wall.

Draw a line on the outer edge of the bracket (as shown).

Slide the bracket towards the center of cabinet and

align the outside edge of the bracket with the marked

line, keeping the rear end edge leaning on the wall.

 Use a pencil to mark 3 holes.

Remove the bracket. Using a 7/64” drill bit, drill 3 holes

where marked.

Assemble the bracket to the cabinet bottom using a

Phillips screwdriver and 3 provided countersunk wood

screws. Repeat for the other cabinet side

HORIZONTAL EXHAUST INSTALLATION ONLY

Install the hood (EZ1 brackets)

NOTE: The following procedure applies to both

framed or frameless cabinet installations.

1. Run house power cable between service panel and

hood location.

2. There are 2 pairs of recessed holes on each side of the

top of the hood (on rear: A and B, on front C and D on

illustration below); these holes allow the range hood to

hang on the brackets (previously installed).

3. Temporarily hang the hood on the brackets using its

2 recessed REAR HOLES (A and B). While holding the

hood, run the house power cable into the hood through

the strain relief previously installed i

n step 5 on page 8.

4. Unhook the rear holes from the brackets and hang the

hood using its 2 recessed FRONT HOLES (C and D).

While holding the hood, attach the power cable to the

hood using the strain relief.

VERTICAL EXHAUST INSTALLATION ONLY

5. Hang the hood on the brackets using the 2 recessed

FRONT HOLES (C and D). While holding the hood, run

the house power cable into the hood through the strain

relief previously installed in step 5 on page 8. Attach

power cable to the hood.

DUCTED INSTALLATIONS ONLY

6. Connect the ductwork to the hood and use metal foil duct tape to make joints secure and air-tight. Make sure the

damper assembly (or round duct plate) enters the ductwork and that the damper opens and closes freely.

FRAMED CABINET FRAMELESS CABINET

OOD

SCREWS

METAL

SCREWS

7. For framed cabinet, secure the hood to the EZ1 brackets

using 4 no. 8-18 x 1/2” metal screws (screws included in

parts bag).

Insert 2 screws per side, in the slots

(as shown in inset on illustration beside).

8. For frameless cabinet, secure the hood to the cabinet

using 4 no. 8 x 5/8” round head wood screws (screws

included in parts bag). Insert 2 screws per side, in the

slots (as shown in inset on illustration beside).

3¼” x 10”

VERTICAL DUCTING

3¼” x 10”

HORIZONTAL DUCTING

7” ROUND

VERTICAL DUCTING

1. Use these diagrams for proper placement of ductwork

and electrical cutout in cabinet or wall.

For a non-ducted installation, DO NOT cut a duct

access hole, only cut the hole for electrical wiring

Standard Installation (without EZ1 brackets)

VERTICAL DUCT

ACCESS HOLE

/16"

5¼"

CENTER

LINE

HOOD MOUNTING SCREWS (4)

ELECTRICAL

ACCESS HOLE

(

IN CABINET BOTTOM)

WOOD SHIMS

(

RECESSED-BOTTOM

CABINETS

ONLY)

CABINET FRONT

3/4"

1⅜"

1½"

7³/16"

12⅞" (30" HOOD)

15⅞" (36"

HOOD)

/16"

CABINET

BOTTOM

12⅞" (30"

HOOD)

15⅞" (36"

HOOD)

CABINET

BOTTOM

CABINET FRONT

HORIZONTAL DUCT

ACCESS HOLE

HOOD

MOUNTING

SCREWS (4)

ELECTRICAL

ACCESS HOLE

(

IN WALL)

3⅞"

CENTER

LINE

WOOD SHIMS

(

RECESSED-BOTTOM

CABINETS

ONLY)

13/16"

3/16"

5¼"

12⅞" (30" HOOD)

15⅞" (36"

HOOD)

12⅞" (30"

HOOD)

15⅞" (36"

HOOD)

7³/

16"

ELECTRICAL

ACCESS HOLE

(

IN CABINET BOTTOM)

HOOD MOUNTING SCREWS (4)

4¹¹/16"

8" DIA.

HOLE

7-IN. ROUND

DUCT

ACCESS

HOLE

7-IN. ROUND

DUCT

ACCESS

HOLE

WOOD SHIMS

(

RECESSED-BOTTOM

CABINETS

ONLY)

12⅞" (30"

HOOD)

15⅞" (36"

HOOD)

12⅞" (30"

HOOD)

15⅞" (36"

HOOD)

/16"

1½"

1⅜"

7³/

16"

2. Install part-way four (4) ROUND HEAD no. 8 x 5/8”

mounting screws into shims/cabinet, according to

the proper diagram above. (Mounting screws are

included in parts bag, but wood shims and shim

mounting screws are not included)

Install the Hood (Standard Installation)

1. Run house power cable between service panel and hood

location. Run the house power cable into the hood through

the strain relief previously installed in step 5 on page 8.

2. Hang hood from (4) mounting screws previously installed.

Slide hood back towards wall until mounting screw heads

are engaged in narrow end of keyhole slots in top of hood.

Tighten screws securely. Attach power cable to the hood

using the strain relief.

DUCTED INSTALLATIONS ONLY

3. Connect the ductwork to the hood and use metal foil duct tape to make joints secure and air-tight. Make sure

the damper assembly (or round duct plate) enters the ductwork and that the damper opens and closes freely.

NOTE: Two installers are recommended because of the weight of this hood.

WARNING: Risk of electric shock. Electrical wiring

must be done by qualiﬁ ed personnel in accordance

with all applicable codes and standards.

Before connecting wires, switch power oﬀ at

service panel and lock service disconnecting

means to prevent power from being switched on

accidentally.

1. Connect House Power Cable to range hood wiring: BLACK

to BLACK, WHITE to WHITE and GREEN or bare wire

under GREEN ground screw.

2. Reinstall wiring cover and attach it to the hood using its

retaining screw.

CONNECT THE WIRING

MOTOR

GROUND

WIRE

HOUSE

POWER

CABLE

GROUND

SCREW

TABS ON

INNER TOP

OF HOOD

ENGAGED IN

WIRING

COVER SLOTS.

CAUTION: Ensure both tabs on inner top of hood are

engaged in their corresponding slots in wiring cover.

Also, take care not to pinch wires while reinstalling

wiring cover.

INSTALL THE FILTERS

1. Align the bulb leads with the small indentations located on

the border of the lamp location on hood (see inset above),

then install the bulbs by placing the bulb leads into their

grooves in the socket.

CAUTION: Most GU10 LED replacement bulbs

commonly found in the market are not designed

for use in a cooking environment and might not

perform as advertised. Their usage with this

product is not recommended.

INSTALL THE LIGHT BULBS

This range hood requires two shielded Halogen Bulbs (120 V, 50 W max., MR16 or PAR16 with GU10 base).

NOTE: The Suction Cup Tool (included with hood) can be used to install and remove light bulbs. Press suction cup tool on

bulb and rotate counterclockwise to remove bulb or clockwise to install bulb.

SUCTION

CUP TOOL

BULB

LEADS

BULB LEAD

GROOVES

(IN SOCKET)

WARNING: Do not touch lamps during or soon

after operation. Burns may occur. In order to

prevent the risk of personal injury, only install

shielded halogen lamps. Also, never install a cool

beam, a dichroic lamp, a lamp not suitable for

use in recessed luminaires or identiﬁ ed for use in

enclosed ﬁ xtures.

INDENT

2. Gently push upwards and turn clockwise until secure.

Ducted Installation Only:

Re-install grease ﬁ lters removed in step 1 on page 7, under

“Prepare the Hood”.

Non-ducted Installation Only:

Purchase two non-ducted ﬁ lters (see part number in Service

parts list). Attach the non-ducted ﬁ lters following instructions

packed with the non-ducted ﬁ lters.

“Non-ducted Filters” available by calling

1-844-553-6667

SERVICE PARTS

KEY NO. PART NO. DESCRIPTION

QUANTITY

51282 51283 51289 51292 51293 51299

S97020030 R

ECIRCULATION COVER PLATE, WHITE (INCL. SCREWS)1 1

S97020031 R

ECIRCULATION COVER PLATE, STAINLESS STEEL (INCL. SCREWS)1 1

S97020029 R

ECIRCULATION COVER PLATE, BLACK (INCL. SCREWS)11

2 SR680508 7'' R

OUND DUCT PLATE (INCLUDING SCREWS) 111111

3 S97020534 3¼”

X 10” DAMPER ASSEMBLY (INCLUDING SCREWS)111111

4 S97020409 B

LOWER MOTOR (INCL. 4 SCREWS AND 1 CAPACITOR)111111

5 S97020407 F

ANPELLER (INCLUDING ITEM 6) 111111

6 SR99420635 C

LIP FOR FANPELLER 111111

S99010434-002 G

REASE FILTER - MICRO MESH - TYPE C1 (SET OF 2) 1 1 1

S99010434-003 G

REASE FILTER - MICRO MESH - TYPE D1 (SET OF 2) 1 1 1

8 S97020427 M

ECHANICAL PUSH-BUTTON CONTROL (6 BUTTONS) 111111

9 SV05921 S

HIELDED HALOGEN BULB 50 W, GU10 222222

* S97020450 W

IRE HARNESS 111111

* S98011637 W

IRING COVER 111111

* S97020292

ARTS BAG INCLUDING: 1 SUCTION CUP TOOL,

4 METAL SCREWS NO. 8-18 X 1/2”,

6 ROUND HEAD NO. 8 X 5/8” WOOD SCREWS,

6 NO. 8 X 1/2” COUNTERSUNK WOOD SCREWS

111111

* S97020466

ON-DUCTED FILTER - TYPE XC (SET OF 2)

(NON-DUCTED INSTALLATION ONLY)

111

* S97020467

ON-DUCTED FILTER - TYPE XD (SET OF 2)

(NON-DUCTED INSTALLATION ONLY)

111

* S99527587 N

ON-DUCTED FILTER CLIP KIT (INCLUDES 4 CLIPS) 111111

* S97020470 E

ASY INSTALL KIT (INCLUDING HARDWARE) 111111

Order replacement parts by PART NO. - not by KEY NO.

* Not illustrated

REPLACEMENT PARTS

In order to ensure your unit remains in good working condition, you must use the manufacturer genuine replacement parts only. The

manufacturer genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable

certiﬁ cation standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage and

drastically reduce the performance level of your unit, which will result in premature failing. To purchase the genuine replacement parts

listed above, call 1-844-553-6667.

LEA Y CONSERVE ESTAS INSTRUCCIONES

TABLA DE CONTENIDO

SECCIÓN ............................................................... PÁGINA

Garantía ..................................................................................... 17

Instrucciones de seguridad ...................................................... 18

Operación ................................................................................... 19

Limpieza ...................................................................................... 19

Piezas incluidas con la campana .......................................... 20

Piezas no incluidas con la campana .................................... 20

Herramientas necesarias ......................................................... 20

Cuadro de largo equivalentes de conducto ......................... 21

Instale los conductos ................................................................ 22

Prepare la campana ........................................................ 22-24

Prepare la ubicación para la campana ......................... 25-28

Instalación EZ1 por una persona .............................. 25-26

Instale la campana (Soportes EZ1) ............................... 27

Instalación normal (Sin soportes EZ1) .......................... 28

Instale la campana (Instalación normal) ..................... 28

Conecte el cableado ............................................................... 29

Instale las bombillas................................................................. 30

Instale los ﬁ ltros ........................................................................ 30

Piezas de servicio ...................................................................... 31

GARANTÍA LIMITADA DE KENMORE

4. Daños en el aparato o fallos causados en él debidos

a una instalación no realizada por técnicos de servicio

autorizados de Sears, incluyendo en ello los casos de

instalación no conformes con los códigos de electricidad,

gas y plomería.

5. Daños en el aparato o fallos causados en él — entre

ellos la descoloración o la oxidación superﬁ cial— si no

se usa correctamente o no se le da mantenimiento de

acuerdo con todas las instrucciones dadas.

6. Daños en el aparato o fallos causados en él — entre el-

los la descoloración o la oxidación superﬁ cial— debidos

a un accidente, alteración, abuso, mal uso o uso distinto

al previsto.

7. Daños en el aparato o fallos causados en él — entre el-

los la descoloración o la oxidación superﬁ cial— debidos

al uso de detergentes, limpiadores, productos químicos

o utensilios distintos a los recomendados en todas las

instrucciones dadas con el producto.

8. Daños en piezas o sistemas del aparato o fallos causados

en ellos debidos a modiﬁ caciones no autorizadas hechas

en el aparato.

9. Gastos de servicio en un aparato cuya placa con el

modelo y número de serie ha desaparecido, ha sido

alterada o no pueda comprobarse fácilmente que lleva

el logo de certiﬁ cación apropiado.

Denegación de garantías implícitas; limitación de los

recursos

El único recurso de que dispone el cliente conforme a

esta garantía limitada será la reparación o la sustitución

del producto, tal y como aquí se indica. Las garantías

implícitas, tales como las garantías de comerciabilidad o

de idoneidad para un determinado propósito, se limitan

a un año para la campana de cocina y a treinta días

para las piezas pintadas o metálicas brillantes, o al peri-

odo más corto que permita la ley. El vendedor no será re-

sponsable de los daños incidentales o derivados. Algunos

estados y provincias no permiten que se excluyan o lim-

iten los daños incidentales o derivados o que se limite la

duración de las garantías implícitas de comerciabilidad o

idoneidad; en tales casos, estas exclusiones o limitaciones

no se aplican a usted.

Esta garantía sólo se aplica cuando el aparato se usa en

Estados Unidos.

Esta garantía le concede derechos legales especíﬁ cos,

y usted puede tener también otros derechos que varían

de un estado a otro.

Sears Brands Management Corporation,

Hoﬀ man Estates, Illinois 60179

GARANTÍA LIMITADA DE KENMORE

La garantía siguiente se aplica, CON UN COMPROBANTE

DE VENTA, cuando este aparato se instala, se utiliza y se

mantiene de acuerdo con todas las instrucciones dadas.

Este aparato está garantizado DURANTE UN AÑO, a partir

de la fecha de venta, contra los defectos de material

y de mano de obra. Un aparato defectuoso será reparado

o sustituido, se gún decida el vendedor. El periodo de garantía

de UN AÑO no se aplica al acabado de las piezas

pintadas o de las piezas metálicas brillantes.

Durante un plazo de TREINTA DÍAS a partir de la fecha

de compra, las piezas pintadas o metálicas brillantes de

este producto serán sustituidas sin gastos si su acabado

tiene defectos de material o de mano de obra.

Para mayor información sobre la forma de obtener una

reparación o una sustitución gratuita, sírvase consultar la

página web www.kenmore.com/warranty

La garantía queda anulada si este producto se utiliza

alguna vez con ﬁ nes distintos al uso doméstico privado.

Esta garantía cubre ÚNICAMENTE los defectos de material

y mano de obra y NO los siguientes casos:

1. Artículos fungibles que pueden desgastarse con el uso

normal, tales como ﬁ ltros, correas, bolsas o bombillas.

2. Gastos generados por un técnico de servicio para

limpiar o dar mantenimiento a este aparato o para dar

instrucciones al usuario sobre la instalación, funcionamiento

y mantenimiento correctos del aparato.

3. Solicitudes de servicio para corregir una instalación

del aparato no realizada por técnicos de servicio

autorizados de Sears o para reparar problemas de los fusibles,

disyuntores y cableado domésticos y de los sistemas de

plomería o de alimentación de gas causados por dicha

instalación.

INSTRUCCIONES DE SEGURIDAD

PREVISTO PARA COCINAR DOMÉSTICO SOLAMENTE.

ADVERTENCIA

PARA REDUCIR EL RIESGO DE INCENDIO, CHOQUE

ELÉCTRICO, O LESIÓN A PERSONAS, OBSERVE LO

1. Utilice esta unidad sólo en la manera prescrita por el

fabricante. Si tiene usted alguna pregunta, comuniqúese

con el fabricante a la dirección o al télefono indicados

en la garantía.

2. Antes de efectuar algún servicio o limpieza, se debe

desconectar la corriente eléctrica en el armario de

circuitos y asegurarlo con llave para evitar que la corriente

sea conectada accidentalmente. Cuando el medio de

desconexión del servicio no puede ser trabado, sujete un

dispositivo de advertencia evidente, tal como una etiqueta,

al panel de servicio.

3. Todo trabajo do instalación y cableado eléctrico debe ser

realizado por personal caliﬁ cado y de acuerdo con todos

los códigos y normas pertinentes, incluyendo los códigos

y normas relacionados con construcción clasiﬁ cada para

incendio.

4. Aire suﬁ ciente es necesario para facilitar la combustión

adecuada y la salida apropiada de gases por la chimenea

de la unidad y para evitar corrientes de aire invertidas.

Siga las instrucciones y medidas de seguridad del

fabricante del equipo y de las sociedades profesionales de

equipos do calentadores y los reglamentos de seguridad

locales.

5. Al cortar o perforar la pared o el techo, no dañe el

cableado eléctrico y otros servicios públicos ocultos.

6. Para reducir el riesgo de incendio o de descarga eléctrica,

no utilice esta campana con un dispositivo de control de

velocidad adicional.

7. Los ventiladores con conducto deberán siempre tener una

salida hacia el exterior.

8. Para reducir el riesgo de incendio, use sólo conductos de

metal.

9. Esta unidad se debe instalar con conexión a tierra.

PARA REDUCIR EL RIESGO DE UN INCENDIO POR GRASA

EN LA ESTUFA:

1. Nunca deje las unidades de superﬁ cie sin supervisión

cuando tengan ajustes altos. Los reboses pueden provocar

humo y derrames grasosos que se pueden incendiar.

Caliente lentamente el aceite en un ajuste bajo o medio.

2. Siempre ENCIENDA la campana cuando cocine con alta

temperatura o cuando cocine alimentos que se puedan

incendiar.

3. Limpie con frecuencia los ventiladores. No debe permitir

que la grasa se acumule en el ventilador ni en el ﬁ ltro.

4. Utilice un sartén de tamaño adecuado. Siempre utilice el

utensilio adecuado al tamaño del elemento do superﬁ cie.

ADVERTENCIA

PARA REDUCIR EL RIESGO DE LESIONES A PERSONAS EN

CASO DE INCENDIO DE GRASA EN LA ESTUFA, OBSERVE

LO SIGUIENTE:*

1. APAGUE LAS LLAMAS con una tapa ajustada, plancha

para galletitas o charola decorativa, y luego apague la

hornilla. TENGA CUIDADO DE EVITAR QUEMADURAS. Si

las llamas no se apagan de inmediato, EVACÚE EL LUGAR

Y LLAME AL DEPARTAMENTO DE BOMBEROS.

2. NUNCA LEVANTE UNA SARTEN QUE ESTÉ EN LLAMAS

- Usted se podrá quemar.

3. NO UTILICE AGUA, incluyendo toallas de cocina mojadas

- puede resultar una explosión de vapor violenta.

4. Utilice un extintor SOLAMENTE si:

A. Usted sabe que tiene un extintor de clase ABC y ya

sabe utilizarlo.

B. El incendio es pequeño y contenido dentro del área

donde se inició.

C. Los bomberos han sido avisados.

D. Usted puede combatir el incendio con una salida a su

espalda.

* Basado en las recomendaciones para “Seguridad en la

Cocina” publicadas por NFPA de los EE.UU.

PRECAUCIÓN

1. Solamente para uso general de ventilación. No utilice para

descargar materiales peligrosos o materiales y vapores

explosivos.

2. Para evitar daños al cojinete del motor y evitar que las

paletas del ventilador emitan mucho ruido o estén fuera

de equilibrio, mantenga el motor libre de pelusa, polvo,

etc.

3. Para obtener mejores resultados en la captura de

impurezas, la parte superior de la campana debe estar

montada de forma tal que la campana quede de 18-24”

de distancia de la superﬁ cie de la estufa.

4. Use sólo kits de cable de conexión para campana de

cocina cuyo uso ya se haya estudiado y aprobado para

este modelo de campana.

5. Por favor, lea la etiqueta de especiﬁ caciones del producto

para mayores informaciones y requerimientos.

NOTA

Si se instalará la campana en un sistema sin conductos:

• Compre dos ﬁ ltros de recirculación y Instale los ﬁ ltros

de recirculación siguiendo las instrucciones que vienen

con los ﬁ ltros.

“Filtros de recirculación”

disponibles llamando al

1-844-553-6667

LIMPIEZAOPERACIÓN

ADVERTENCIA: Para reducir el riesgo de una

descarga eléctrica, desconecte el suministro

eléctrico antes de limpiar la unidad.

Filtros de microﬁ ltración

Limpie frecuentemente los ﬁ ltros con agua caliente y un

detergente suave. Los ﬁ ltros se pueden lavar en lavaplatos. Se

debe lavar los ﬁ ltros de malla de aluminio aproximadamente

cada mes, dependiendo de su uso. Lávelos con mayor

frecuencia si su forma de cocinar genera más grasa - como,

por ejemplo, frituras o ‘wok’.

Filtros de recirculación

(disponibles por separado – ver página 20)

Los ﬁ ltros de recirculación deberían cambiarse cada 3 a

6 meses. Sustitúyalo con mayor frecuencia si su tipo de

cocina genera más grasa, por ejemplo si fríe o cocina con

wok. Consulte las instrucciones de instalación que vienen

con el ﬁ ltro de recirculación.

Superﬁ cies pintadas de la campana

Limpie con agua tibia y un detergente suave únicamente.

Si la superﬁ cie se descolora, use una cera para acabados,

como una cera para automóviles. (NO use productos

limpiadores duros o abrasivos ni limpiadores para porcelana.)

Superﬁ cies de acero inoxidable de la campana

A hacer:

• Lávelo regularmente con un trapo limpio empapado con

una disolución de agua tibia y jabón suave o detergente

para lavar vajillas.

• Limpie siempre en la dirección de las líneas de pulido.

• Enjuague siempre bien con agua limpia (2 o 3 veces)

después de limpiar. Séquelo completamente.

• También puede usar un producto limpiador doméstico

para acero inoxidable.

A no hacer:

• Usar lana de acero o de acero inoxidable o un rascador

para quitar la suciedad más incrustada.

• Usar productos limpiadores agresivos o abrasivos.

• Dejar que se acumule la suciedad.

• Permitir que el polvo de yeso u otros residuos de

construcción entren en contacto con la campana.

Durante los trabajos de construcción o renovación,

cubra la campana para evitar que el polvo se adhiera

a las superﬁ cies de acero inoxidable.

Al elegir un detergente, evite:

• Los productos limpiadores que contengan blanqueador

(lejía) ya que dañarán el acero inoxidable.

• Los productos que contengan: cloruro,

ﬂ uoruro,

yoduro, bromuro, ya que deteriorarán las superﬁ cies

rápidamente.

• Los productos combustibles que se usan para limpiar,

tales como: acetona, alcohol, éter, benzol, etc., ya que

son muy explosivos y no deberían usarse nunca cerca

de una cocina.

Montaje del ventilador

El motor está lubricado permanentemente y no necesita

engrase nunca. Si los rodamientos del motor hacen un ruido

excesivo o no habitual, sustituya el motor por otro idéntico.

También se debería sustituir la hélice.

BOTÓN PULSADOR

ENCENDIDO/

APAGADO DEL

VENTILADOR

BOTÓN PULSADOR ENCENDIDO/APAGADO DEL

VENTILADOR

Cuando el ventilador impelente esté APAGADO, pulse este

botón pulsador para ENCENDER el ventilador impelente en

la última velocidad seleccionada. Pulsa de nuevo este botón

pulsador para apagar el ventilador.

NOTA: Si no hay una velocidad seleccionada (todos los

botónes pulsadores de las velocidades del

ventilador hacia arriba), el ventilador no se

encenderá. En este caso, pulsa el botón pulsador de

la velocidad deseada para encender el ventilador.

BOTONES PULSADORES DE LAS VELOCIDADES

DEL VENTILADOR

Cuando el ventilador impelente esté ENCENDIDO, cambia

la velocidad del ventilador al pulsar el botón pulsador

correspondiente a la velocidad deseada: una lìnea para

BAJA, dos lìneas para MEDIA y tres lìneas para ALTA.

BOTÓN PULSADOR ENCENDIDO/APAGADO DE LA LUZ

Cuando las luces estén apagadas, pulsa este botón

pulsador para ENCENDER las luces en la última intencidad

seleccionada. Pulsa de nuevo este botón para APAGAR las

luces.

BOTÓN PULSADOR DE LA INTENSIDAD DE LA LUZ

Pulsa este botón para cambiar la intensidad de la luz (ALTA

o BAJA).

BOTONES PULSADORES

DE LAS VELOCIDADES

DEL VENTILADOR

BOTÓN PULSADOR

ENCENDIDO/

APAGADO

DE LA LUZ

BOTÓN PULSADOR

DE LA INTENSIDAD

DE LA LUZ

PIEZAS INCLUIDAS CON LA CAMPANA

HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN DE LA CAMPANA

PIEZAS NO INCLUIDAS CON LA CAMPANA

Filtros de grasa

de microﬁ ltración

(2 por campana)

Bolsa de piezas

(4 tornillos para metal n.° 8-18 x 1/2",

6 tornillos de cabeza redonda

para madera n.° 8 x 5/8", 6 tornillos

embuditos para madera n.° 8 x 1/2",

1 ventosa para bombillas)

PIEZAS OPTATIVAS (compra separada)

Filtros de recirculación

(Campana sin conducto

unicamente)

(2 por campana)

Pieza:

N.° S97020466 (anchura de 30'')

N.° S97020467 (anchura de 36'')

Regulador de tiro

redondo de 7"

(Para uso con conducto

redondo de 7"

Pieza N.° 59183

Conjunto de la

clapeta de retención

3¼” x 10”

Apoyar este borde contra la pared de atrásPlace this edge against back wall

VERTICAL EXHAUST

RTICAL EX

= 3¼” x 10”

= 3¼” x 14”

RECTANGULAR DUCTING7” ROUND DUCTING

Use this template for marking; do not attempt to cut out the ducting hole through it.

NOTE: These cutouts are clearance holes; they do not need to be the exact size of ducting.

= 3¼ po x 10 po

= 3¼ po x 14 po

CONDUIT RECTANGULAIRECONDUIT ROND DE 7 PO

= 3¼ pulg. x 10 pulg.

= 3¼ pulg. x 14 pulg.

CONDUCTO RECTANGULARCONDUCTO REDONDO

7 PULG.

Appuyer ce bord au mur arrière

Utiliser ce gabarit pour marquer vos repères; ne pas tenter de découper

le trou pour le conduit à travers le gabarit.

NOTE : Les découpes incluent le jeu nécessaire à l’installation; elles ne doivent pas

être du format exact des conduits.

Use esta plantilla para crear marcados; no trate de cortar el

agujero del conducto a través de la plantilla.

NOTA: To be translated in Spanish.

MARK WHERE INDICATED

FOR THE APPROPRIATE SIZE DUCT OPENING

MARQUER LES REPÈRES AUX ENDROITS INDIQUÉS SELON

LE FORMAT DE CONDUIT UTILISÉ

TITLE TO BE TRANSLATED IN SPANIS H

Electrical access hole center

A = single blower hood

B = double blower hood

Centre du trou pour fil

d’alimentation électrique

A = hotte ventilateur simple

B = hotte ventilateur double

To be translated in Spanish

Electrical access hole center

A = single blower hood

B = double blower hood

4¼”

10½”

14½”

8”

7½”

Bend template along graduated

scale when installing to framed

cabinet.

Pour une installation sous une

armoire à fond en retrait, utiliser les

lignes pour mesurer l’épaisseur du

décalage causé par le mur de

l’armoire et plier le gabarit en

conséquence.

To be translated in Spanish.

Sistema de instalación EZ1

por una persona

(incluso plantilla para

instalación de conductos,

impresa por ambos lados,

y soportes de instalación)

Conector de

conducto

redondo de 7”

Destornillador

(chato y Phillips)

Lápiz

Cinta métrica

Perforadora

(con broca de 1/8",

broca de 7/64", y

serrucho de calar

de 1½")

Cinta adhesiva

metálica

para conductos

Pelador de

cable

Pinzas de

punta

HR0064

Tijera para

hojalatero

Sierra

de punta

Serrucho

de punta

-o-

Bombillas halógenas

con pantalla

(120 V, 50 W max.,

MR16 o PAR16 con base GU10)

(2 por campana)

Las “Piezas no incluidas con la campana” están

disponibles llamando al 1-844-553-6667

La page charge ...

Kenmore 51299 Le manuel du propriétaire

Marque: Kenmore

Modèle: 51299

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 51299 Owner's manual
español: Kenmore 51299 El manual del propietario

Kenmore 51299 Le manuel du propriétaire

Ce manuel convient également à

Kenmore 51299 Le manuel du propriétaire

dans d''autres langues

Autres documents