Whirlpool CED9150GW Guide d'installation

INSTALLATION INSTRUCTIONS

Commercial Dryer Gas or Electric

www.whirlpoolcommerciallaundry.com

W10919522A

W10919523A—SP

INSTRUCTIONS D’INSTALLATION

Sécheuse à usage commercial

à gaz ou électrique

2

DRYER SAFETY

■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer

smells gas. This information should be obtained from your gas supplier.

■ Post the following warning in a prominent location.

TABLE OF CONTENTS

Page

DRYER SAFETY ....................................................................... 2

INSTALLATION REQUIREMENTS ........................................... 5

Tools and Parts .................................................................... 5

Dimensions/Clearances ...................................................... 6

Venting Requirements ........................................................ 7

Gas Dryer Installation Requirements ................................ 10

Electric Dryer Installation Requirements ........................... 14

INSTALLING LEVELING LEGS, COIN SLIDE,

AND COIN BOX ..................................................................... 17

INSTALLATION INSTRUCTIONS – GAS DRYER .................. 18

Make Gas Connection ...................................................... 18

INSTALLATION INSTRUCTIONS – ELECTRIC DRYER ....... 19

Electric Dryer Electrical Connections ............................... 19

LEVELING .............................................................................. 24

COMPLETE INSTALLATION ................................................. 24

REVERSING DRYER DOOR SWING .................................... 25

MAINTENANCE INSTRUCTIONS ......................................... 27

IF YOU NEED ASSISTANCE ................................................. 27

ELECTRONIC CONTROL SETUP INSTRUCTIONS ........... 28

WARRANTY .......................................................................... 34

TABLE DES MATIÈRES

Page

SÉCURITÉ DE LA SÉCHEUSE .............................................. 35

EXIGENCES D’INSTALLATION ............................................. 38

Outils et pièces .................................................................. 38

Dimensions/Distances de dégagement ............................. 39

Exigences concernant l’évacuation ................................... 40

Exigences d’installation pour la sécheuse à gaz ................ 43

Exigences d’installation pour la sécheuse électrique ........ 47

INSTALLATION DES PIEDS DE NIVELLEMENT,

DE LA GLISSIÈRE À MONNAIE ET DE LA CAISSE

À MONNAIE ........................................................................... 49

INSTRUCTIONS D’INSTALLATION

POUR LA SÉCHEUSE À GAZ ................................................ 50

Raccordement à la canalisation de gaz ............................. 50

NIVELLEMENT .......................................................................51

ACHEVER L’INSTALLATION ................................................. 52

INVERSION DU SENS D’OUVERTURE

DE LA PORTE DE LA SÉCHEUSE ........................................53

INSTRUCTIONS D’ENTRETIEN ............................................55

SI VOUS AVEZ BESOIN D’ASSISTANCE .............................. 55

INSTRUCTIONS DE RÉGLAGE DU TABLEAU

DE COMMANDE ÉLECTRONIQUE ...................................... 56

GARANTIE ............................................................................. 63

3

DRYER SAFETY

4

DRYER SAFETY

5

Tools Needed:

8" (200 mm) 8" (200 mm) or 10" (250 mm) Flat-Blade Screwdriver Phillips Screwdriver

or 10" (250 mm) Adjustable Wrench

Pipe Wrench that opens to 1" (25 mm)

TORX

®

T-20

®†

Security 1" (25 mm) Hex-Head 1⁄4" Socket Wrench Pliers (that open to

Screwdriver or Bit Socket Wrench 1

9

/

16

" [39 mm])

Level Utility Knife 1/4" (6 mm) Nut Driver 27" (686 mm)

Wood Block

Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound Putty Knife

(for installing new exhaust vent) suitable for gas type

Flashlight (optional) 1" (25 mm) Ruler or Measuring Tape

Open-End Wrenches

INSTALLATION REQUIREMENTS

†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

Parts Supplied:

Foot Boots (4) Leveling Legs (4)

Tools and Parts

6

INSTALLATION REQUIREMENTS

Front View Side View Back View

Dimensions

Clearances

Recessed Front View Closet Side View

Bottom Exhaust

Dimensions/Clearances

7

INSTALLATION REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible metal vent shall be used for

exhausting.

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may result

in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 7

3

⁄

4

ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or exible metal vents. Review “Vent System Chart” and

if necessary, modify existing vent system to achieve best drying

performance.

NOTE: Although each single-load dryer should typically have

an unobstructed outdoor air opening of 24" (154 cm) (based

on 1" [6.5 cm] per 1,000 Btu [252 kcal]), common make-up air

openings are also acceptable.

Set up common openings so the make-up air is distributed

equally to all dryers. Coverage area must be increased by 33%

to account for the use of registers or louvers.

Make-up air openings should not be installed near the building

exits for exhaust vents.

4"

(102 mm)

4" (102 mm) heavy, metal exhaust vent

Elbows:

■ 45° elbows provide better airow than 90° elbows.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Improper venting can cause moisture and lint to collect

indoors, which may result in:

Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

Housecleaning problems and health problems.

Better

Good

Venting Requirements

8

4" (102 mm) Diameter Exhaust Hoods

Box Hood Louvered Hood Angled Hood

Vent Hoods

INSTALLATION REQUIREMENTS

Exhaust hood must be at least 12" (305 mm) from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

For vent systems not covered by the vent specication chart,

see your parts distributor.

Provision must be made for enough air for combustion

and ventilation. (Check governing codes and ordinances.)

See “Recessed Area and Closet Installation Instructions”

in the “Location Requirements” sections.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄

2

"

(64 mm) outlet exhaust hood may be used. A 2

1

⁄

2

" (64 mm)

outlet creates greater back pressure than other hood types.

For permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 4" (102 mm) clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

12" min.

(305 mm)

Vent collar

Vent System Chart (Rigid Metal Vent)

No. of

90˚ Turns

Box and

Louvered Hood

Angled Hood

0 130 ft. (39.6 m) 129 ft. (39.3 m)

1 125 ft. (38.1 m) 119 ft. (36.3 m)

2 115 ft. (35.1 m) 109 ft. (33.2 m)

3 106 ft. (32.3 m) 100 ft. (30.5 m)

4 98 ft. (29.9 m) 92 ft. (28.0 m)

9

The outside end of main vent should have a sweep elbow

directed downward.

If main vent travels vertically through the roof, rather than

through wall, install a 180° sweep elbow on end of vent at least

2 ft. (610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1/2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

12" min.

(305 mm)*

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 5663 l/min. (200 CFM)

of air per dryer. Large-capacity lint screens of proper design

may be used in main vent if checked and cleaned frequently.

The room where the dryers are located should have make-up

air equal to or greater than CFM of all the dryers in the room.

Back-draft Damper Kit is available from your distributor and

should be installed in the vent of each dryer to keep exhausted

air from returning into dryers and to keep exhaust in balance

within main vent. Unobstructed return air openings are required.

Each vent should enter the main vent at an angle pointing in

the direction of the airow. Vents entering from the opposite

side should be staggered to reduce the exhausted air from

interfering with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

Keep air openings free of dry cleaning uid fumes. Fumes

create acids which, when drawn through the dryer heating

units, can damage dryers and items being dried.

A clean-out cover should be located on the main vent

for periodic cleaning of the vent system.

If an Exhaust Hood Cannot be Used Multiple Dryer Venting

INSTALLATION REQUIREMENTS

24" min.

(610 mm)

* Minimum clearance above

any accumulation of snow,

ice, or debris such as leaves

30˚ max.

Air ow

Air Flow

10

Your dryer can be installed in a basement, laundry room,

or recessed area.

This dryer is not intended for installation in a mobile home.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to water and/or the weather. Proper installation is your

responsibility.

You will need:

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■ A level oor with a maximum slope of 1" (25 mm) under

entire dryer. Installing the dryer on soft oor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

Gas dryer installation clearances

■ The location must be large enough to allow the dryer door

to be fully opened.

■ Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

■ Additional clearances might be required for wall, door,

and oor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

■ Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

■ Make sure that lower edges of the cabinet, plus the back

and bottom sides of the dryer, are free of obstructions to

permit adequate clearance of air openings for combustion

air. See “Recessed Area and Closet Installation Instructions”

below for minimum spacing requirements.

Location Requirements

INSTALLATION REQUIREMENTS

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in “Dimensions/Clearances.”

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes

and ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors

with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same

closet as the dryer.

24 in.

2

(155 cm

2

)

48 in.

2

(310 cm

2

)

3"

(76 mm)

3"

(76 mm)

Closet

door

Front

View

Closet

Door

Front

View

Gas Dryer Installation Requirements

11

Gas Dryer Grounding

IMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA

70, latest edition, or Canadian Electrical Code, CSA C22.1.

If codes permit and a separate ground wire is used, it is

recommended that a qualied electrical installer determine

that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■ Do not ground to a gas pipe.

■ Do not have a fuse in the neutral or ground circuit.

■ A 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

■ This dryer is equipped with a power supply cord having

a 3-prong grounding plug.

■ To minimize the possibility of shock, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualied electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

■ Check with a qualied electrician if you are not sure

the dryer is properly grounded.

INSTALLATION REQUIREMENTS

Electrical Requirements

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

12

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and

ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certied by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level

at the B.T.U. rating indicated on the model/serial plate. Burner

input adjustments are not required when the dryer is operated

up to this elevation.

Gas Supply

INSTALLATION REQUIREMENTS

When installed above 10,000 feet (3048 m), a four percent

(4%) reduction of the burner B.T.U. rating shown on the model/

serial plate is required for each 1,000 foot (305 m) increase in

elevation. For assistance when converting to other gas types

and/or installing above 10,000 feet (3048 m) elevation, contact

your local service company.

Gas supply pressure required to operate this dryer is

a minimum of 5.2" wc (1.30 kPa) and a maximum of

10.5" wc (2.62 kPa).

13

This dryer is equipped for use with natural gas. It is design-

certied by CSA International for LP (propane and butane)

gases with appropriate conversion. No attempt shall be made

to convert dryer from gas specied on serial/rating plate for use

with a different gas without consulting the serving gas supplier.

Conversion must be done by a qualied service technician.

Gas conversion kit part number is W10402145. This number

can also be found on a label on the gas valve burner base.

Type of Gas

INSTALLATION REQUIREMENTS

Recommended Method

Provide a gas supply line of 1⁄2" (13 mm) rigid (IPS) pipe to

dryer location. Pipe joint compounds that resist action of LP

gas must be used. Do not use TEFLON

®†

tape. With LP gas,

piping or tubing size can be 1⁄2" (13 mm) minimum. Usually, LP

gas suppliers determine size and materials used in the system.

Gas Supply Pressure Testing

A 1/8" NPT minimum plugged tapping, accessible for gauge

testing, must be installed immediately downstream of the

installed shut-off valve to the dryer (as shown above). The

dryer must be disconnected from the gas supply piping system

during any pressure testing of the system at test pressures in

excess of 1/2" psig (352 kg/m

2

).

Expected Pressures For Gas Supply

Minimum

Inches of Water

Maximum

Inches of Water

Natural Gas 5.2 10.5

LP Gas 8.0 13.0

Alternate Method

The gas supply may also be connected using 3⁄8" (10 mm)

approved copper or aluminum tubing. If the total length of

the supply line is more than 20 ft. (6.1 m), larger tubing will

be required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off

valve installed within 6 ft. (1.8 m) of dryer in accordance

with National Fuel Gas Code, ANSI Z223.1. This valve should

be located in same room as dryer. It should be in a location

that allows ease of opening and closing. Do not block access

to shut-off valve. In Canada, an individual manual shut-off

valve must be installed in accordance with the B149 installation

codes CAN/CGA B149.1 and CAN/CGA B149.2.

Gas Supply Line

Flexible Metal Appliance Connector

It is recommended that a new exible stainless steel gas line,

design-certied by CSA International, be used for connecting

the dryer to the gas supply line. (The gas pipe which extends

through the lower rear of the dryer is provided with 3⁄8"

male pipe thread.)

NOTE: Do not kink or damage the exible stainless steel gas

line when moving the dryer.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe ttings

to obtain an in-line connection to the dryer.

†®TEFLON is a registered trademark of Chemours.

14

Your dryer can be installed in a basement, laundry room,

or recessed area.

This dryer is not intended for installation in a mobile home.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to water and/or the weather. Proper installation is your

responsibility.

You will need:

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■ A level oor with a maximum slope of 1" (25 mm) under

entire dryer. Installing the dryer on soft oor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

Electric dryer installation clearances

■ The location must be large enough to allow the dryer door

to be fully opened.

■ Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

■ Additional clearances might be required for wall, door,

and oor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in “Dimensions/Clearances.”

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes

and ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors

with equivalent air openings are acceptable.

Location Requirements

The dryer must be exhausted outdoors.

24 in.

2

(155 cm

2

)

48 in.

2

(310 cm

2

)

3"

(76 mm)

3"

(76 mm

)

Closet

door

Front

View

INSTALLATION REQUIREMENTS

Closet

Door

Front

View

Electrical Requirements – U.S.A. only

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

■ The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

■ A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch

Park, Quincy, MA 02269.

■ To supply the required 3- or 4-wire, single-phase, 120/240

volt, 60 Hz., AC-only electrical supply (or 3- or 4-wire,

120/208 volt electrical supply, if specied on the serial/

rating plate) on a separate 30-amp circuit, fused on both

sides of the line. A time delay fuse or circuit breaker is

recommended. Connect to an individual branch circuit.

Do not have a fuse in the neutral or grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

Electric Dryer Installation Requirements

15

Electrical Requirements – U.S.A. only (cont.)

Electrical Connection

To properly install your dryer, you must determine the type

of electrical connection you will be using and follow the

instructions provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor

is permanently connected to the neutral conductor (white

wire) within the dryer. If the dryer is installed with a 4-wire

electrical supply connection, the neutral ground conductor

must be removed from the external ground connector

(green screw), and secured under the neutral terminal

(center or white wire) of the terminal block. When the neutral

ground conductor is secured under the neutral terminal

(center or white wire) of the terminal block, the dryer cabinet

is isolated from the neutral conductor.

■ If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-wire

connection” section.

■ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

and (2) areas where local codes prohibit grounding through

the neutral conductor.

Electric Dryer Power Supply Cord

If using a power supply cord:

Use a UL-listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

■ A UL-listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or “U”-shaped spade terminals

with upturned ends.

■ A UL-listed strain relief.

If your outlet looks like this:

4-wire

receptacle

(14-30R)

3-wire

receptacle

(10-30R)

Then choose a 4-wire power supply cord with ring

or spade terminals and UL-listed strain relief. The

4-wire power supply cord, at least 4 ft. (1.22 m)

long, must have four 10-gauge copper wires and

match a 4-wire receptacle of NEMA Type 14-30R.

The ground wire (ground conductor) may be either

green or bare. The neutral conductor must be

identied by a white cover.

Then choose a 3-wire power supply cord with ring

or spade terminals and UL-listed strain relief. The

3-wire power supply cord, at least 4 ft. (1.22 m)

long, must have three 10-gauge copper wires and

match a 3-wire receptacle of NEMA Type 10-30R.

If your outlet looks like this:

INSTALLATION REQUIREMENTS

Electric Dryer Grounding

16

Direct Wire

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper

cable (with ground wire), covered with exible metallic

conduit. All current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

INSTALLATION REQUIREMENTS

Electrical Requirements – Canada only

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code,

C22.1 – latest edition and all local codes. A copy of the

above codes standard may be obtained from: Canadian

Standards Association, 178 Rexdale Blvd., Toronto, ON

M9W 1R3 CANADA.

■ To supply the required 4 wire, single phase, 120/240 volt,

60 Hz., AC-only electrical supply on a separate 30-amp

circuit, fused on both sides of the line. A time-delay fuse

or circuit breaker is recommended. Connect to an individual

branch circuit.

■ This dryer is equipped with a CSA International

Certied Power Cord intended to be plugged into

a standard 14-30R wall receptacle. The cord is

5 ft (1.52 m) in length. Be sure wall receptacle is

within reach of dryer’s nal location.

■ Do not use an extension cord.

If you are using a replacement power supply cord,

it is recommended that you use Power Supply Cord

Replacement Part Number 8579325. For further information,

please reference the service numbers located in the

“Assistance or Service” section.

4-wire

receptacle

(14-30R)

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualied electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not t the outlet, have a proper outlet

installed by a qualied electrician.

17

INSTALLING LEVELING LEGS, COIN SLIDE, AND COIN BOX

The coin slide mechanism, control panel lock and key, and

coin box lock and key are not included and are available from

usual industry sources. A special coin slide extension must be

used on this model and can be purchased from the coin slide

distributor.

1. Prepare dryer for leveling legs

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging oor covering.

Using two or more people, move dryer to desired installation

location.

Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe drum interior with damp

cloth to remove any dust.

Take two cardboard corners from the dryer carton and place

them on the oor in back of the dryer. Firmly grasp body of

the dryer and gently lay it on its back on the cardboard corners.

2. Screw in leveling legs

Examine leveling legs and nd diamond

marking. Screw legs into leg holes by

hand. Use an adjustable wrench or 1"

(25 mm) hex-head socket wrench to

nish turning legs until diamond marking

is no longer visible. Then t a covered foot

boot over each leg foot. For oors with

greater slopes, a longer leveling foot

(part no. 279810) is available.

To protect the oor, use a large piece of cardboard from the

dryer carton. Stand dryer up on the cardboard. Slide the dryer

until it is close to its nal location. Leave enough room for

electrical connection and to connect the exhaust vent.

On some models: The meter case houses the factory-installed

coin slide mechanism, service lock and key, and coin box lock

and key.

3. Install coin slide and coin box

Remove the service door of the meter case by lifting

it up at the back. Install the money-accepting device.

(Refer to manufacturer’s instructions for proper installation.)

Replace the meter case service door. Put the coin vault with

lock and key in the meter case opening.

Remove cardboard or hardboard from under dryer. Adjust

the legs of the dryer up or down until the dryer is level.

Foot

Diamond

Marking

18

1. Remove red cap from gas pipe on back of dryer.

2. Connect gas supply to dryer. Use a pipe thread compound

approved for the type of gas supplied. If exible metal

tubing is used, be certain there are no kinks.

If necessary for service, open the front lower service panel

by using a 1/4" nutdriver to remove the 2 hex-head screws

from the bottom of the panel. Then lift up on the panel while

pulling the bottom of the panel away from the dryer.

3. Open the shut-off valve in the gas supply line and make sure

the dryer has its own gas supply opened.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show

a leak. Correct any leaks found.

Make Gas Connection

INSTALLATION INSTRUCTIONS – GAS DRYER

19

Power Supply Cord Strain Relief

1. Insert strain relief.

2. Insert power cord into strain relief.

Remove Terminal Block Cover

Strain Relief

INSTALLATION INSTRUCTIONS – ELECTRIC DRYER

Direct Wire Strain Relief

1. Insert strain relief.

2. Insert conduit into strain relief and tighten clamp.

Electric Dryer Electrical Connections

20

INSTALLATION INSTRUCTIONS – ELECTRIC DRYER

Power Cord

4-wire receptacle (NEMA Type 14-30R)

3-wire receptacle (NEMA Type 10-30R)

Standard Power Supply Cord Connectors

Flanged Spade Connector Ring Connector

Connecting Ground and Neutral Wires

1. Remove center terminal block screw and the ground wire

by removing the external ground connector screw.

2. Connect ground and neutral wire to center terminal block.

Connection Options

Connecting 4-Wire Connection: Power Supply Cord

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire

connections.

Direct Wire

4-wire direct

3-wire direct

1"

(25 mm)

5"

(127 mm)

Connecting Power Cord Ground Wire

3. Connect ground wire (green or bare) with external ground

connector screw.

Connecting Remaining Wires

4. Connect remaining wires with outer terminal block screws.

La page charge ...

Whirlpool CED9150GW Guide d'installation

Ce manuel convient également à

Whirlpool CED9150GW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents