Amana AGR5835QDS Manuel utilisateur

Important Safety Instructions ......................... 1-4

Surface Cooking ................................................ 5-7

Controls

Sealed Gas Burners

Oven Cooking .................................................. 8-17

Baking

Cook & Hold

Delay

Keep Warm

Broiling

Oven Racks

Care & Cleaning ............................................ 18-21

Self-Clean Oven

Cleaning Procedures

Maintenance .................................................. 22-23

Oven Window & Light

Removal of Gas Appliance

Troubleshooting ............................................ 24-25

Warranty & Service..............................................27

Guide d’utilisation et d’entretien ......................28

Guía de Uso y Cuidado .......................................56

Gas - Easy Touch Control 800

Use & Care Guide

Range

Form No. A/01/08 Part No. 8113P712-60

1

Installer: Please leave this manual with this appliance.

Consumer: Please read and keep this manual for future

reference. Keep sales receipt and/or canceled check as proof

of purchase.

Model Number __________________________________

Serial Number __________________________________

Date of Purchase ________________________________

If you have questions, call:

Customer Assistance

1-800-688-9900 USA

1-800-688-2002 Canada

Internet: http://www.amana.com

In our continuing effort to improve the quality and performance

of our cooking products, it may be necessary to make changes

to the appliance without revising this guide.

For service information, see page 27.

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible conditions

and situations that may occur. Common sense, caution,

and care must be exercised when installing, maintaining,

or operating the appliance.

Always contact your dealer, distributor, service agent, or

manufacturer about problems or conditions you do not

understand.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which

COULD result in severe personal injury or death.

CAUTION – Hazards or unsafe practices which

COULD result in minor personal injury.

WARNING

CAUTION

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance must

be properly installed and grounded by a qualified techni-

cian. Do not attempt to adjust, repair, service, or replace

any part of your appliance unless it is specifically recom-

mended in this guide. All other servicing should be

referred to a qualified servicer. Have the installer show

you the location of the gas shut off valve and how to

shut it off in an emergency.

Always disconnect power to appliance before servicing.

If the information in this manual is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or death.

– Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any appliance.

– IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

– Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING

General Instructions

WARNING: To reduce risk of

tipping of the appliance from

abnormal usage or by excessive loading of the

oven door, the appliance must be secured by a

properly installed anti-tip device.

WARNING

• ALL RANGES CAN TIP AND

CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE

• FOLLOW ALL INSTALLATION

INSTRUCTIONS

Gas leaks may occur in your system and result in a

dangerous situation. Gas leaks may not be detected

by smell alone. Gas suppliers recommend you pur-

chase and install an UL approved gas detector. Install

and use in accordance with the manufacturer’s

instructions.

WARNING

Important Safety

Instructions

2

Do not use water on grease fires. Use baking soda, a

dry chemical or foam-type extinguisher to smother fire

or flame.

Child Safety

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear

leveling legs is properly engaged in the bracket slot. The

anti-tip device secures the rear leveling leg to the floor

when properly engaged. You should check this anytime

the range has been moved.

To Prevent Fire or Smoke

Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from com-

bustible materials, gasoline, and other flammable vapors

and materials.

If appliance is installed near a window, proper precau-

tions should be taken to prevent curtains from blowing

over burners.

NEVER leave any items on the cooktop. The hot air from

the vent may ignite flammable items and may increase

pressure in closed containers which may cause them to

burst.

Many aerosol-type spray cans are EXPLOSIVE when

exposed to heat and may be highly flammable. Avoid

their use or storage near an appliance.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or

hot. Do not leave plastic items on the cooktop as they

may melt or soften if left too close to the vent or a

lighted surface burner.

To eliminate the hazard of reaching over hot surface

burners, cabinet storage should not be provided directly

above a unit. If storage is provided, it should be limited

to items which are used infrequently and which are

safely stored in an area subjected to heat from an

appliance. Temperatures may be unsafe for some items,

such as volatile liquids, cleaners or aerosol sprays.

In Case of Fire

Turn off appliance and ventilating hood to avoid spread-

ing the flame. Extinguish flame then turn on hood to

remove smoke and odor.

• Cooktop: Smother fire or flame in a pan with a lid or

cookie sheet.

NEVER pick up or move a flaming pan.

• Oven: Smother fire or flame by closing the oven door.

CAUTION

NEVER store items of interest to children in cabinets

above an appliance or on backguard of a range.

Children climbing on the appliance door to reach

items could be seriously injured.

NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot.

NEVER allow children to sit or stand on any part of the

appliance as they could be injured or burned.

Children must be taught that the appliance and utensils

in it can be hot. Let hot utensils cool in a safe place, out

of reach of small children. Children should be taught

that an appliance is not a toy. Children should not be

allowed to play with controls or other parts of the unit.

About Your Appliance

Important Safety Instructions

WARNING

NEVER use appliance door as a step stool or seat as this

may result in possible tipping of the appliance and serious

injuries.

NEVER use this appliance as a space heater to heat or

warm a room. Doing so may result in carbon monox-

ide poisoning and overheating of the oven.

NEVER cover any slots, holes or passages in the oven

bottom or cover the entire rack with materials such as

aluminum foil. Doing so blocks air flow through the

oven and may cause carbon monoxide poisoning.

Aluminum foil may also trap heat causing a fire

hazard.

NEVER obstruct the flow of combustion and ventilation

air by blocking the oven vent or air intakes. Doing so

restricts air to the burners and may result in carbon

monoxide poisoning.

The oven vent is located at the base of the backguard.

Avoid touching oven vent area while oven is on and for

several minutes after oven is turned off. Some parts of

3

Cooking Safety

Always place a pan on a surface burner before turning it

on. Be sure you know which knob controls which

surface burner. Make sure the correct burner is turned

on and that the burner has ignited. When cooking is

completed, turn burner off before removing pan to

prevent exposure to burner flame.

Always adjust surface burner flame so that it does not

extend beyond the bottom edge of the pan. An exces-

sive flame is hazardous, wastes energy and may damage

the appliance, pan or cabinets above the appliance.

NEVER leave a surface cooking operation unattended

especially when using a high heat setting or when deep

fat frying. Boilovers cause smoking and greasy spillovers

may ignite. Clean up greasy spills as soon as possible.

Do not use high heat for extended cooking operations.

NEVER heat an unopened container on the surface

burner or in the oven. Pressure build-up may cause

container to burst resulting in serious personal injury or

damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause

burns from steam. Dish towels or other substitutes

should never be used as potholders because they can

trail across hot surface burners and ignite or get caught

on appliance parts.

Always let quantities of hot fat used for deep fat frying

cool before attempting to move or handle.

Do not let cooking grease or other flammable materials

accumulate in or near the appliance, hood or vent fan.

Clean hood frequently to prevent grease from accumu-

lating on hood or filter. When flaming foods under the

hood turn the fan on.

NEVER wear garments made of flammable material or

loose fitting or long-sleeved apparel while cooking.

Clothing may ignite or catch utensil handles.

Always place oven racks in the desired positions while

oven is cool. Slide oven rack out to add or remove food,

using dry, sturdy potholders. Always avoid reaching into

the oven to add or remove food. If a rack must be moved

while hot, use a dry potholder. Always turn the oven off at

the end of cooking.

Use care when opening the oven door. Let hot air or

steam escape before moving or replacing food.

PREPARED FOOD WARNING: Follow food

manufacturer’s instructions. If a plastic frozen food con-

tainer and/or its cover distorts, warps, or is otherwise

damaged during cooking, immediately discard the food

and its container. The food could be contaminated.

NEVER use aluminum foil to cover oven racks or oven

bottom. This could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

Utensil Safety

Use pans with flat bottoms and handles that are easily

grasped and stay cool. Avoid using unstable, warped,

easily tipped or loose-handled pans. Also avoid using

pans, especially small pans, with heavy handles as they

could be unstable and easily tip. Pans that are heavy to

move when filled with food may also be hazardous.

Be sure utensil is large enough to properly contain food

and avoid boilovers. Pan size is particularly important in

deep fat frying. Be sure pan will accommodate the volume

of food that is to be added as well as the bubble action of

fat.

To minimize burns, ignition of flammable materials and

spillage due to unintentional contact with the utensil, do

not extend handles over adjacent surface burners. Always

turn pan handles toward the side or back of the appliance,

not out into the room where they are easily hit or reached

by small children.

Never let a pan boil dry as this could damage the utensil

and the appliance.

Follow the manufacturer’s directions when using oven

cooking bags.

Only certain types of glass, glass/ceramic, ceramic or

glazed utensils are suitable for cooktop or oven usage

without breaking due to the sudden change in tempera-

ture. Follow manufacturer’s instructions when using glass.

Important Safety Instructions

the vent and surrounding area become hot enough to

cause burns. After oven is turned off, do not touch the

oven vent or surrounding areas until they have had

sufficient time to cool.

Other potentially hot surfaces include cooktop, areas

facing the cooktop, oven vent, surface near the vent

opening, oven door, area around the oven door and

oven window.

Do not touch a hot oven light bulb with a damp cloth as

the bulb could break. Should the bulb break, disconnect

power to the appliance before removing bulb to avoid

electrical shock.

4

This appliance has been tested for safe performance

using conventional cookware. Do not use any devices or

accessories that are not specifically recommended in

this guide. Do not use eyelid covers for the surface

units, stovetop grills, or add-on oven convection sys-

tems. The use of devices or accessories that are not

expressly recommended in this manual can create

serious safety hazards, result in performance problems,

and reduce the life of the components of the appliance.

Cleaning Safety

Turn off all controls and wait for appliance parts to cool

before touching or cleaning them. Do not touch the

burner grates or surrounding areas until they have had

sufficient time to cool.

Clean appliance with caution. Use care to avoid steam

burns if a wet sponge or cloth is used to wipe spills on a

hot surface. Some cleaners can produce noxious fumes

if applied to a hot surface.

Self-Clean Oven

Important Safety Notice and

Warning

The California Safe Drinking Water and Toxic Enforce-

ment Act of 1986 (Proposition 65) requires the Governor

of California to publish a list of substances known to the

State of California to cause cancer or reproductive harm,

and requires businesses to warn customers of potential

exposures to such substances.

Users of this appliance are hereby warned that the

burning of gas can result in low-level exposure to some

of the listed substances, including benzene, formalde-

hyde and soot, due primarily to the incomplete combus-

tion of natural gas or liquid petroleum (LP) fuels. Prop-

erly adjusted burners will minimize incomplete combus-

tion. Exposure to these substances can also be mini-

mized by properly venting the burners to the outdoors.

Users of this appliance are hereby warned that when

the oven is engaged in the self-clean cycle, there may

be some low-level exposure to some of the listed

substances, including carbon monoxide. Exposure to

these substances can be minimized by properly venting

the oven to the outdoors by opening the windows and/

or door in the room where the appliance is located

during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS:

Never keep pet birds in the kitchen or in rooms where

the fumes from the kitchen could reach. Birds have a

very sensitive respiratory system. Fumes released during

an oven self-cleaning cycle may be harmful or fatal to

birds. Fumes released due to overheated cooking oil, fat,

margarine and overheated non-stick cookware may be

equally harmful.

Save These Instructions for Future Reference

Important Safety Instructions

CAUTION

Before self-cleaning the oven, remove the oven racks,

broiler pan, food and any other utensils. Wipe

spillovers to prevent excessive smoke and flare-ups.

Clean only parts listed in this guide. Do not clean door

gasket. The door gasket is essential for a good seal.

Care should be taken not to rub, damage, or move the

gasket. Do not use oven cleaners of any kind in or

around any part of the self-clean oven.

It is normal for the cooktop of the range to become hot

during a self-clean cycle. Therefore, touching the

cooktop during a clean cycle should be avoided.

5

Surface Cooking

Surface Controls

Pilotless Ignition

Pilotless ignition eliminates the

need for a constant standing

pilot light. Each surface burner

has a spark ignitor. Use care

when cleaning around the

surface burner.

If the surface burner does

not light, check if ignitor is

broken, soiled or wet.

Setting the controls:

The size and type of cookware will affect the heat setting.

1. Place a pan on the burner grate.

• The burner flame may lift off or appear separated from

the port if a pan is not placed on the grate.

2. Push in and turn the knob counterclockwise to the Light

setting.

• A clicking (spark) sound will be heard and the burner

will light. (All four ignitors will spark when any surface

burner knob is turned to the Light position.)

3. After the burner lights, turn knob to desired flame size.

• The ignitor will continue to spark until the knob is

turned past the Light position.

Operating During a

Power Failure

Surface Control Knobs

Use to turn on the surface burners. An infinite choice of heat

settings is available from Low to High. At the High setting a

detent or notch may be felt. The knobs can be set on or

between any of the settings.

Graphics next to the knob identify which burner the

knob controls. For example, the graphic at left shows

the left front burner location.

CAUTION

• If flame should go out during a cooking operation, turn

the burner off. If a strong gas odor is detected, open a

window and wait five minutes before relighting the

burner.

• Be sure all surface controls are set in the OFF position

prior to supplying gas to the range.

• NEVER touch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the burners, to

become warm or hot during cooking. Use potholders to

protect hands.

CAUTION

When lighting the surface burners, be sure all of the

controls are in the OFF position. Strike the match first and

hold it in position before turning the knob to Light.

High: Use to bring liquid to a boil, or reach

pressure in a pressure cooker. Always

reduce setting to a lower heat when liquids

begin to boil or foods begin to cook.

An intermediate flame size is used to

continue cooking. Food will not cook any

faster when a higher flame setting is used

than needed to maintain a gentle boil.

Water boils at the same temperature

whether boiling gently or vigorously.

Low: Use to simmer foods, keep foods

warm and melt chocolate or butter. Some

cooking may take place on the Low

setting if the pan is covered. It is possible

to reduce the heat by rotating the knob

toward OFF. Be sure flame is stable.

1. Hold a lighted match to the desired surface burner head.

2. Push in and turn the control knob slowly to Light.

3. Adjust the flame to the desired level.

6

Cooktop

Notes:

• A properly adjusted burner with clean ports will light

within a few seconds. If using natural gas, the flame

will be blue with a deeper blue inner cone.

If the burner flame is yellow or is noisy, the air/gas

mixture may be incorrect. Contact a service technician

to adjust. (Adjustments are not covered by the war-

ranty.)

With LP gas, slight yellow tips on the flames are

acceptable. This is normal and adjustment is not

necessary.

• With some types of gas, you may hear a “popping”

sound when the surface burner is turned off. This is a

normal operating sound of the burner.

• If the control knob is turned very quickly from High to

Low, the flame may go out, particularly if the burner is

cold. If this occurs, turn the knob to the OFF position,

wait several seconds and relight the burner.

• The flame should be adjusted so it does not extend

beyond the edge of the pan.

To prevent the cooktop from discoloring or

staining:

• Clean cooktop after each use.

• Wipe acidic or sugary spills as soon as the cooktop has

cooled as these spills may discolor the

porcelain.

Unlike a range with standard gas burners,

this cooktop does not lift-up nor is it

removable. Do not attempt to lift the

cooktop for any reason.

Sealed Burners

The sealed burners of your range are secured to the cooktop

and are not designed to be removed. Since the burners are

sealed into the cooktop, boilovers or spills will not seep

underneath the cooktop.

However, the burner should be cleaned after each use. The

head portion of the burner is easily removed for cleaning.

(See page 20 for cleaning directions.)

The burner heads must be correctly placed on the burner

base for proper operation of the burner.

High Performance Burner

(16,000 BTU*)

There is one high speed burner on your range, located in the

right front position. This burner offers higher speed cooking

that can be used to quickly bring water to a boil and for large-

quantity cooking.

Simmer Burner

This burner is located in the right rear position. The simmer

burner offers a lower BTU flame for delicate sauces or melting

chocolate.

* BTU ratings will vary when using LP gas.

Surface Cooking

Burner Grates

The grates must be properly positioned before cooking.

When installing the grates, place the tab ends toward the

center, matching the straight bars.

Improper installation of the grates may result in chipping of

the cooktop.

Do not operate the burners without a pan on the grate.

The grate’s porcelain finish may chip without a pan to

absorb the heat from the burner flame.

Use care when stirring food in a pot/pan sitting on the burner

grate. The grates have a smooth finish for ease of cleaning.

The pot/pan will slide if the handle is not held. This may result

in spilling of hot food items and may be a burn hazard.

Although the burner grates are durable, they will gradually

lose their shine and/or discolor, due to the high temperatures

of the gas flame.

7

Surface Cooking

Control Panel

The control panel is designed for ease in programming. The display window on the control shows time of day, timer and oven functions.

Control panel shown includes model specific features. (Styling may vary depending on model.)

Using the Touchpads

• Press the desired pad.

• Press the number pads to enter time or temperature.

• Press the Autoset 0 pad to enter temperature.

• A beep will sound when any pad is touched.

• A double beep will sound if a programming error occurs.

A Convect Use for convection baking and

roasting.

B Bake Use for baking and roasting.

C Broil Use for broiling and top browning.

D Cancel Cancels all operations except Timer

and Clock.

E Clock Use to set time-of-day clock.

F Oven Light Use to turn the oven light on or off.

G Favorite Use to set and save a specific Cook &

Hold procedure.

H Clean Use to set self-clean cycle.

I Cook & Hold Bakes for a preset time, then holds

food warm for 1 hour.

J Keep Warm Use to keep cooked food warm in oven.

K Delay Programs the oven to start baking at

a later time.

L Number Pads Use to set time and temperature.

M Autoset Use to quickly set temperatures.

N Timer Sets Timer.

A B C D E F G H

I J K L M N

Note: Four seconds after pressing the number pads or

the Autoset 0 pad, the time or temperature will automati-

cally be entered. If more than 30 seconds elapse between

touching a function pad and the number pads or the

Autoset 0 pad, the function will be canceled and the

display will return to the previous display.

8

Oven Cooking

cont.

Clock

The clock can be set to display time in a 12-hour or 24-hour

format. The clock is set at the factory for the 12-hour format.

To change the clock to

24-hour format:

1. Press and hold the Cancel and Favorite

pads for three seconds.

• 12 Hr flashes in the display.

2. Press the Autoset 0 pad to select 24 Hr;

press again to select 12 Hr.

3. Set the time of day following the directions

in the To set the Clock section.

To set the Clock:

1. Press the Clock pad.

• The time of day flashes in the display.

2. Press the appropriate number pads to set the time of day.

• Colon flashes in the display.

3. Press the Clock pad again or wait four seconds.

• The colon will remain on.

When electrical power is supplied or after a power interrup-

tion, the last clock time before power was interrupted will

flash.

9

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for Delay cook or clean or Cook & Hold.

To cancel the Clock display:

If you do not want the time of day to display:

Press and hold the Cancel and Clock pads

for three seconds. The time of day will

disappear from the display.

When the clock display is canceled, press

the Clock pad to briefly display the time of

day.

When the clock display is canceled, after 15 minutes, the oven

control will go into Standby Mode to save energy. The display

will be blank and the oven light will not operate. To “wake up”

the control from Standby Mode, press any touchpad. A double

beep will sound.

To restore the Clock display:

Press and hold the Cancel and Clock pads for three seconds.

The time of day will reappear in the display.

Timer

The timer can be set from one minute (0:01) up to 99 hours

and 59 minutes (99:59).

The timer can be used independently of any other oven

activity. It can also be set while another oven function is

operating.

The Timer does not control the oven. It only controls a

beeper.

To set the Timer:

1. Press the Timer pad.

• 0:00 and TIMER flash in the display.

2. Press the appropriate number pads until the correct time

appears in the display.

• The colon and TIMER will continue to flash.

3. Press Timer pad again or wait four seconds.

• The colon stops flashing and the time begins counting

down.

• The last minute of the timer countdown will be displayed

in seconds.

4. At the end of the set time, one long beep will sound and

“End” will be displayed.

5. Press the Timer pad to clear the display.

To cancel the Timer:

1. Press and hold the Timer pad for three

seconds.

OR

2. Press the Timer pad and press ‘0’ using the

number pads.

Locking the Control

and Oven Door

The touchpad and oven door can be locked for safety,

cleaning, or to prevent unwanted use. The touchpads will not

function when locked.

If the oven is currently in use, the touchpads and door cannot

be locked.

The current time of day will remain in the display when the

touchpads and door are locked.

To lock:

Press and hold the Cancel and Cook &

Hold pads for three seconds. (Press the

Cancel pad first.)

• OFF appears in the display

• LOCK flashes while the door

is locking.

To unlock:

Press and hold the Cancel and Cook & Hold pads for three

seconds. (Press the Cancel pad first.) OFF disappears from the

display.

Note: The touchpads and oven door cannot be locked if

the oven temperature is 400° F or above.

Fault Codes

BAKE or LOCK may flash rapidly in the display to alert you if

there is an error or a problem. If BAKE or LOCK flash in the

display, press Cancel pad. If BAKE or LOCK continue to flash,

disconnect power to the appliance. Wait a few minutes, and

then reconnect power. If the flashing still continues, discon-

nect power to the appliance and call an authorized servicer.

Oven Cooking

10

Baking Notes:

• To change the oven temperature during cooking, press

Bake pad, then press the Autoset 0 pad or appropriate

number pads until the desired temperature is displayed.

• To change the oven temperature during preheat, press

the Bake pad twice, then press the Autoset 0 pad or

appropriate number pads until the desired temperature is

displayed.

• If you forget to turn off the oven, it will automatically turn

off at the end of 12 hours. If you wish to deactivate this

feature, see page 14.

Baking

To set Bake:

1. Press the Bake pad.

• BAKE will flash.

• 000 will flash in the display.

2. Select the oven temperature. Press

the Autoset 0 pad for 350° F or the

appropriate number pads.

• Each additional press of the Autoset 0 pad will increase

the temperature by 25°.

• The oven temperature can be set from 170° to 550°.

3. Press Bake pad again or wait four seconds.

• BAKE will stop flashing and light in the display.

Baking Differences Between Your Old

and New Oven

It is normal to notice some baking time differences between a

new oven and an old one. See “Adjusting the Oven Temperature”

on page 15.

Baking and Roasting with

Convection

When using convection, enter your normal baking

temperature. The control will automatically reduce the set

oven temperature by 25°. The entered temperature will be

displayed. The convection fan will start after the oven has

been on for five minutes.

To set Convect:

1. Press the Convect pad.

• BAKE and the FAN icon will flash.

• 000 will flash in the display.

2. Select the oven temperature. Press the

Autoset 0 pad for 350° F or the appropriate

number pads.

• Each additional press of the Autoset 0 pad will increase

the temperature by 25 degrees. The oven temperature

can be set from 170° to 550°.

• 100° or the actual oven temperature if over 100° F will

display. It will rise in 5° increments until the preset

temperature is reached.

4. Allow the oven to preheat for 8-15 minutes.

• When the set oven temperature is reached, one long

beep will sound.

• The set temperature will display.

• To recall set temperature during preheat, press Bake pad.

5. Place food in the oven.

6. Check cooking progress at the minimum cooking time.

Cook longer if needed.

7. When cooking is finished, press Cancel pad.

8. Remove food from the oven.

cont.

Oven Cooking

11

3. Press Convect pad again or wait four seconds.

• BAKE will stop flashing.

• 100° or the actual oven temperature if over 100° F will

display. It will rise in 5° increments until the preset

temperature is reached.

• The FAN icon will start to rotate.

4. Allow the oven to preheat for 8-15 minutes.

• When the set oven temperature is reached, one long

beep will sound.

• The set temperature will display.

• To recall the set temperature during preheat, press the

Convect pad.

5. Place food in the oven.

6. Check cooking progress at the minimum cooking time.

Cook longer if needed.

7. When cooking is finished, press Cancel pad.

8. Remove food from the oven.

Cook & Hold

When using the Cook & Hold option, the oven begins to heat

immediately after the control has been set. Then, the oven

cooks for a specified length of time. When that time has

elapsed, the oven will keep the food warm for up to an hour

then automatically turn off.

To set Cook & Hold:

1. Press the Cook & Hold pad.

• HOLD will flash to indicate that you are in Cook &

Hold programming.

• 00:00 will flash in the display.

2. Select the amount of time you want to cook by using the

number pads.

• HOLD continues to flash.

• The time will light in the display.

• Time can be set from ten minutes (00:10) to 11 hours, 59

minutes (11:59).

3. While HOLD is still flashing, press Bake or

Convect and select the oven temperature.

Press the Autoset 0 pad for 350° F or the

appropriate number pads.

• BAKE will flash.

• The oven temperature can be set from 170° F to 550° F.

4. Press Bake or Convect again OR wait four seconds.

• BAKE will remain lit.

• The cooking time will show in the display.

• The actual oven temperature will be displayed

during preheat.

• The set temperature will display when the oven is

preheated.

When the cooking time has elapsed:

• Four beeps will sound.

• HOLD and WARM will light.

• 170° will display.

• Time of day will display.

After one hour in HOLD WARM:

• The oven turns off automatically.

• HOLD and WARM go off.

• Remove food from oven.

To cancel Cook & Hold at any time:

Press the Cancel pad. Remove food from oven.

Convect Notes:

• Roasting times can vary with different cuts of meat.

• It is not necessary to preheat when convect roasting

large cuts of meat.

Oven Cooking

12

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry, or seafood.

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time.

Delay time can be set from 10 minutes (00:10) to 11 hours, 59

minutes (11:59).

To set a Delayed Cook & Hold cycle:

1. Press the Delay 1 pad.

• DELAY flashes in the display.

• 00:00 flashes in the display.

2. Using the appropriate number pads, enter the amount of

time you want to delay the start of the Cook & Hold cycle.

3. Press the Cook & Hold pad.

• HOLD and DELAY flash in the display.

• 00:00 flashes in the display.

4. Enter the amount of time you want to cook using the

number pads.

5. Press Bake or Convect.

6. Set the oven temperature desired by

pressing the Autoset 0 pad or the

appropriate number pads.

• 350° will light when Autoset 0 pad is

pressed.

• After four seconds, the entered delay time

will appear in the display.

• HOLD turns off.

• BAKE and DELAY remain lit to remind you that a delayed

Cook & Hold cycle has been programmed.

Delay Cook & Hold

CAUTION

Note:

• Do not use Delayed Cook & Hold for items that require a

preheated oven, such as cakes, cookies, and breads.

• Do not use Delayed Cook & Hold if oven is already hot.

Keep Warm

For safely keeping hot foods warm in the oven or for warming

breads and plates.

To set Keep Warm:

1. Press the Keep Warm pad.

• WARM flashes.

• 000 flashes in the display.

2. Select the Keep Warm temperature by pressing the

Autoset 0 pad or the appropriate number pads.

• 170° will light when the Autoset 0 pad is pressed.

• Each press of the Autoset 0 pad will increase the

temperature by 5°.

The Keep Warm temperature can be set from 145° to 190°.

WARM and the temperature will be displayed while the

function is active.

Keep Warm Notes:

• For optimal food quality, oven cooked foods should be

kept warm for no longer than 1 to 2 hours.

• To keep foods from drying, cover loosely with foil or a lid.

• To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and Autoset 0 pads.

- warm for 12-15 minutes.

• To warm plates:

- place 2 stacks of up to four plates each in the oven.

- press Keep Warm and Autoset 0 pads.

- warm for five minutes, turn off the oven and leave

plates in the oven for 15 minutes more.

- use only oven-safe plates, check with the

manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or

breakage.

To cancel Keep Warm:

1. Press the Cancel pad.

2. Remove food from the oven.

Oven Cooking

13

Broiling

To set Broil:

1. Press the Broil pad.

• BROIL flashes.

• SET flashes.

2. Press the Autoset 0 pad once to set HI

broil or twice to set LO broil.

• HI or LO will be displayed.

• Select HI broil (550° F) for normal broiling. Select

LO broil (450° F) for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

• BROIL will remain lit.

• HI or LO will remain lit.

Broil Notes:

• For best results when broiling, use a pan designed for

broiling.

• HI is used for most broiling. Use LO broil when broiling

longer cooking foods. The lower temperature allows

food to cook to the well done stage without excessive

browning.

• Broil times may be longer when the lower broiling

temperature is selected.

• Most foods should be turned halfway through broiling

time.

4. For optimum browning, preheat for 2-3 minutes before

adding food.

5. Place food in the oven. Close oven door.

6. Turn meat once about halfway through cooking.

7. When food is cooked, press the Cancel pad.

Remove food and broiler pan from the oven.

• The time of day will reappear in the display.

RACK TOTAL

FOOD POSITION DONENESS COOK TIME

Beef Steaks, 1” thick 5 Medium 15-20 min.

5 Well Done 18-24 min.

Hamburger Patties, 3/4” thick 5 or 6 Well Done 13-18 min.

Pork Bacon 5 Well Done 6-10 min.

Ham, precooked 1/2” slice 5 Warm 8-12 min.

Chops, 1” thick 5 Well Done 22-26 min.

Poultry Chicken Breast, bone-in 4 Well Done 30-45 min. (LO broil)

Seafood Fish filets 5 Flaky 8-12 min.

Fish steaks, 1” thick 5 Flaky 10-15 min.

Lobster tails, 3-4 oz. each 5 Done 7-10 min.

Broiling Chart

Preheat oven for 2-3 minutes.

For a browned/seared exterior and rare interior, it may be necessary to decrease cook time on side one and decrease the distance

between the meat and heat source.

Note: This chart is a suggested guide. The times may vary with the food being cooked.

Oven Cooking

14

Sabbath Mode Notes:

• Sabbath Mode can be turned on at any time with or

without the oven on.

• Sabbath Mode cannot be turned on if the touchpads are

locked out or when the door is locked.

• Most prompts and messages and all beeps are

deactivated when Sabbath Mode is active.

• If the oven is baking when Sabbath Mode is set, BAKE

will go out when bake is canceled. There will be no

audible beeps.

• The oven light will not automatically come on when the

oven door is opened while the oven is in Sabbath Mode.

If the oven light is desired while in Sabbath Mode, it

must be turned on before the Sabbath Mode is started.

• When the Sabbath Mode is started, the temperature

display will immediately show the set temperature, rather

than the actual oven cavity temperature. No preheat

beep will sound.

• The self-clean cycle and automatic door lock do not

operate during the Sabbath Mode.

• Pressing Cancel pad will cancel a Bake cycle, however

the control will stay in the Sabbath Mode.

• If power fails, the oven will power up in Sabbath Mode

with 72 hours remaining and no cycle active.

Automatic Shut-Off/Sabbath

Mode

The oven will automatically turn off after 12 hours if you

accidentally leave it on. This safety feature can be turned off.

To cancel the 12-hour shut-off and run the

oven continuously for 72 hours:

1. Press and hold the Clock pad for five

seconds.

• SAb will be displayed and flash for five seconds.

• SAb will then be displayed continuously until turned

off or until the 72-hour time limit is reached.

• BAKE will also be displayed if a bake cycle is in use

while the oven is in Sabbath Mode.

• All other functions EXCEPT BAKE (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

• A Cook & Hold can be programmed during the Sabbath

Mode, however a Delay Cook & Hold is not allowed.

To cancel the Sabbath Mode:

1. Press the CLOCK pad for five seconds.

• SAb will flash for five seconds.

• The time of day will return to the display.

OR

2. After 72 hours, the Sabbath Mode will end.

• SAb will flash for five seconds.

• The time of day will return to the display.

Oven Cooking

15

Favorite

The Favorite pad allows you to save the time and temperature

from a Cook & Hold function.

To set a Favorite cycle, a Cook & Hold function must be either

active or just programmed.

To set a new Favorite cycle or to save a cur-

rently running Cook & Hold as a Favorite:

1. Program a Cook & Hold cycle as described in the Cook &

Hold section on page 11.

2. Press and hold the Favorite pad for three

seconds.

• The newly set or currently running Cook & Hold cycle

will be saved.

• A beep will sound to indicate that the control has

accepted the Favorite setting.

To start a cycle programmed into Favorite:

1. Press the Favorite pad.

• Time and temperature for the set Cook & Hold cycle will

be displayed. (If no Cook & Hold cycle has been pro-

grammed, “nonE” is displayed.)

2. Press the Bake or Convect pad.

• The Favorite cycle will begin immediately.

• BAKE will light in the display.

• The cooking time will light in the display.

When the cooking time has elapsed:

• BAKE will turn off.

• HOLD and WARM will light.

• 170° will display.

To cancel a Favorite cycle in progress:

1. Press the Cancel pad.

• The stored Favorite cycle will not

be affected.

2. Remove food from the oven.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ovens

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or

lower than your recipe recommends, then bake. The results

of the “test” should give you an idea of how much to adjust

the temperature.

To adjust the oven temperature:

1. Press the Bake pad.

2. Enter 550° by pressing the appropriate number pads.

3. Press and hold the Bake pad for several seconds or until 0°

appears in the display.

If the oven temperature was previously adjusted, the

change will be displayed. For example, if the oven tem-

perature was reduced by 15° the display will show “-15°”.

4. Press the Autoset 0 pad to adjust the temperature.

Each time the Autoset 0 pad is pressed, the temperature

changes by 5°. The oven temperature can be increased or

decreased by 5° to 35°.

Pressing the Autoset 0 pad will first cycle through increas-

ing the oven temperature (5, 10, . . . 35). Continuing to

press the Autoset 0 pad will then cycle through decreasing

the oven temperature (-35, -30, . . . -5).

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there is a

power failure or interruption. Temperature adjustment applies

to Bake and Convect only. Broiling and cleaning temperatures

cannot be adjusted.

Oven Cooking

Changing Temp °F/°C

1. The factory default setting for temperature is Fahrenheit.

2. To change the setting, press and hold the CANCEL and Bake

pads at the same time for three seconds.

3. A single beep will sound and the current setting will be

displayed (°F or °C). (If no change is made, the range will

return to the existing setting after 30 seconds.)

4. To change the setting, press the Autoset 0 pad. Press again

to return to existing setting. Wait five seconds and the setting

will be complete.

16

Do not place

plastics near the

vent opening as

heat from the vent

could distort or

melt the plastic.

OVEN VENT

LOCATION

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located below the backguard vent

shield on your range.

Oven Light

The oven light automatically comes on when the

door is opened. When the door is closed, press

the oven light pad to turn the oven light on and

off. A beep will sound every time the oven light

pad is pressed.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven

bottom.

Oven Fan

A convection fan is used to circulate hot air in the oven when

the convection feature is selected. It automatically turns on 5

minutes after the Convect pad is pressed and will turn off

when Convect is canceled.

Note: The convection fan will automatically stop when the

oven door is opened.

CAUTION

Oven Racks

• Do not attempt to change the rack position when the oven

is hot.

• Do not use the oven for storing food or cookware.

The oven has three racks. All racks are designed with a lock-

stop edge.

To remove:

1. Pull rack straight out until it

stops at the lock-stop

position.

2. Lift up on the front of the

rack and pull out.

To replace:

1. Place rack on the rack support in the oven.

2. Tilt the front end up slightly. Slide rack back until it clears

the lock-stop position.

3. Lower front and slide back into the oven.

Do not cover an entire rack with aluminum foil or place

foil on the oven bottom. Baking results will be affected

and damage may occur to the oven bottom.

Rack Positions

RACK 7 (highest

position): For single rack

baking on cookie sheets

and broiling.

RACK 6: Used for single

rack baking on cookie

sheets and broiling. Used

for multiple rack baking.

RACK 5: For single rack

baking on cookie sheets and broiling.

RACK 4: Used for single rack baking on cookie sheets, sheet

cakes, casseroles and broiling. Used for multiple rack baking.

RACK 3: For single rack baking on cookie sheets, casseroles,

layer cakes, loaves of bread and sheet cakes. Used for

multiple rack baking.

RACK 2: Used for single rack baking on cookie sheets and

roasting small cuts of meat. Used for multiple rack baking.

Pilotless Ignition

Your range is equipped with pilotless ignition. With this type of

ignition system, the gas automatically shuts off and the oven

will not operate during a power failure.

A lighted match will not light the oven burner. No attempt

should be made to operate the oven during a power failure.

Oven Cooking

Three Rack

Convection Baking

7

6

5

4

3

2

1

Oven

Bottom

17

EasyRack

TM

The EasyRack

TM

offers a convenient place to grasp bakeware

when taking it out of the oven.

Note:

• Use the EasyRack

TM

only in the oven in which it was

purchased.

RACK 1: Use for roasting large cuts of meat and poultry.

Oven Bottom: Place oven rack on

raised sides of oven bottom. Use

for additional space when cooking

large oven meals.

MULTIPLE RACK COOKING:

Two rack: Use rack positions 3

and 6, or 2 and 4.

Three rack: (convection only) Use rack positions 1, 3 and 6.

Note: When convect baking on two or three racks, check

foods at the minimum suggested time to avoid over-

browning or over-cooking.

Baking Layer Cakes on Two Racks

For best results when baking cakes on two racks, use racks 2 and

4 for regular baking and racks 3 and 6 for convection baking

(select models).

Place the cakes on the rack as shown.

Oven Cooking

18

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

Self-Clean Oven

CAUTION

• It is normal for parts of the range to become hot during a

self-clean cycle.

• To prevent damage to oven door, do not attempt to open

the door when LOCK is displayed.

• Avoid touching cooktop, door, window or oven vent area

during a clean cycle.

• Do not use commercial oven cleaners on the oven finish

or around any part of the oven. They will damage the

finish or parts.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1. Turn off the oven light before cleaning. The light may burn

out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide easily

after a self-clean cycle if they are not removed.

3. Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking

on during the clean cycle. (The gasket is the seal around

the oven door and window.)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic spills are not wiped up before a self-clean

cycle.

Note: Oven temperature must be below 400° F to program

a clean cycle.

Care & Cleaning

1. Close the oven door.

2. Press the Clean pad.

• CLEAN flashes in the display.

• SET flashes in the display.

3. Press the Autoset 0 pad.

• MEd (Medium Soil, 3 hours) is displayed.

4. Press the Autoset 0 pad to scroll through the self-cleaning

settings.

HVy (Heavy Soil, 4 hours)

MEd (Medium soil, 3 hours)

LITE ( Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

5. After four seconds, the oven will start cleaning.

• If the door is not closed, beeps will sound and “door” will

display. If the door is not closed within 30 seconds, the

self-cleaning operation will be canceled and the display

will return to the time of day.

• CLEAN will appear in the display.

• LOCK will flash in the display. Once the door locks, the

word will remain steady.

• The cleaning time will start counting down in the display.

To Delay a Self-Clean Cycle:

1. Press the Delay 1 pad.

• DELAY flashes.

• 00:00 will flash in the display.

2. Enter the amount of time you want to delay the cycle using

the appropriate number pads.

3. Press the Clean pad.

• SET flashes in the display.

4. Press the Autoset 0 pad.

• LITE (Light soil level) is displayed.

cont.

To set Self-Clean:

19

Care & Cleaning

5. Press the Autoset 0 pad to scroll through

the self-cleaning settings.

HVy (Heavy Soil, 4 hours)

MEd (Medium Soil, 3 hours)

LITE (Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, CLEAN and DELAY will light and LOCK

will flash in the display. When the oven door latches,

LOCK will stop flashing and light continuously to show that

the oven is set for a delayed clean operation. The delay

time will display.

Notes:

• If the oven door is left open, “door” will flash in the

display and a signal will beep until the door is closed

and the Clean pad is pressed again.

• If more than five seconds elapse between pressing the

Clean pad and the Autoset 0 pad, the program will

automatically return to the previous display.

• The oven door will be damaged if the oven door is

forced to open when LOCK is still displayed.

After Self-Cleaning

About one hour after the end of the self-clean cycle, LOCK

will turn off. The door can then be opened.

Some soil may leave a light gray, powdery ash. Remove

it with a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be re-

moved during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This is normal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self-clean

cycle. This discoloration is normal and will not affect perfor-

mance.

During the Self-Clean Cycle

When LOCK shows in the display, the door cannot be opened.

To prevent damage to the door, do not force the door open

when LOCK is displayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven is cleaned. This is normal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts

expanding and contracting. This is normal and will not

damage the oven.

La page est en cours de chargement...

Amana AGR5835QDS Manuel utilisateur

Ce manuel convient également à

Amana AGR5835QDS Manuel utilisateur

dans d''autres langues

Autres documents